FCS-1141

H.264 1.3-Megapixel PoE Network Camera

User Manual

Ver1.3

Table of Contents

1.

Overview ................................................................................................................................ 3

1.1

Features ...................................................................................................................... 3

1.2

Package Contents ....................................................................................................... 4

2.

Introduction of IP Camera .................................................................................................... 5

2.1

Camera Dimensions .................................................................................................... 5

2.2

Connectors on the Rear Board .................................................................................... 6

3.

Preparations for IP Camera Setup ....................................................................................... 8

3.1

System Requirements ................................................................................................. 8

3.2

Installation ................................................................................................................... 8

3.3

Accessing IP Camera ................................................................................................ 10

Using recording software....................................................................................................... 14

Installing DC Viewer Software Online.................................................................................... 15

4.

Configuration & Operation ................................................................................................. 17

4.1

Browser-based Viewer Introduction ........................................................................... 17

4.2

Home Page................................................................................................................ 18

4.3

System Related Settings............................................................................................ 20

4.3.1

Host Name and System Time Setting......................................................... 21

4.3.2

Security ...................................................................................................... 22

4.3.3

Network...................................................................................................... 25

4.3.4

DDNS......................................................................................................... 30

4.3.5

Mail ............................................................................................................ 31

4.3.6

FTP ............................................................................................................ 32

4.3.7

Application (Excluding Compact IP Dome) ................................................. 33

4.3.8

Motion Detection ........................................................................................ 39

4.3.9

Storage Management................................................................................. 43

4.3.10 Recording................................................................................................... 45

4.3.11 File Location............................................................................................... 46

4.3.12 Iris Adjustment (Excluding Compact IP Dome) ........................................... 47

4.3.13

View Log File.............................................................................................. 48

4.3.14

View User Information ................................................................................ 49

4.3.15

View Parameters ........................................................................................ 51

4.3.16

Factory Default........................................................................................... 52

4.3.17

Software Version ........................................................................................ 53

4.3.18

Software Upgrade ...................................................................................... 54

4.3.19 Maintenance............................................................................................... 57

4.4

Video and Audio Streaming Settings ......................................................................... 58

4.4.1

Video Resolution and Rotate Type ............................................................. 58

4.4.2

Video Compression .................................................................................... 61

1

4.4.3

Video OCX Protocol ................................................................................... 63

4.4.4

Video Frame Skip....................................................................................... 64

4.4.5

Video Mask ................................................................................................ 65

4.4.6

Audio Mode and Bit Rate Settings.............................................................. 66

4.5

Camera Settings........................................................................................................ 68

4.5.1

Exposure Setting ........................................................................................ 69

4.5.2

White Balance Setting ................................................................................ 70

4.5.3

Backlight Setting ........................................................................................ 71

4.5.4

Brightness Setting ...................................................................................... 71

4.5.5

Sharpness Setting ...................................................................................... 72

4.5.6

Contrast Setting ......................................................................................... 72

4.5.7 Saturation Setting....................................................................................... 72

4.5.8

Digital Zoom Setting ................................................................................... 72

4.5.9

IR Function................................................................................................. 72

4.5.10

WDR Function............................................................................................ 73

4.5.11

3DNR Function........................................................................................... 73

4.5.12

TV System Setup ....................................................................................... 73

4.6

Logout ....................................................................................................................... 74

Appendix A: Technical Specifications ...................................................................................... 75

Appendix B: Internet Security Settings ..................................................................................... 77

Appendix C: DC Viewer Download Procedure .......................................................................... 80

Appendix D: Install UPnP Components..................................................................................... 82

2

1. Overview

Following high standard of Megapixel IP Camera, the HD WDR IP Camera holds pioneer image setting functions to provide the best image quality.

Adopting superior Sony image sensor, the IP Camera is highly sensitive and has good low-light performance.

In addition to MPEG-4 and MJPEG real time streaming, the HD WDR IP

Camera develops superior H.264 codec to smoothly transfer High Definition surveillance data through Internet without distortion. The built-in Wide Dynamic

Range (WDR) function allows getting crystal images even in extreme condition; this feature enhances the camera’s performance in installations include shops, banks, parking lots, factories and building surveillance.

1.1 Features

•

Sony Progressive Scan CCD sensor

•

HD 720p real-time at dual streaming

•

H.264, MJPEG and MPEG-4 compression

•

Integrated real-time WDR

•

2D / 3D Noise Reduction

•

Motion Detection

•

Privacy Masks

•

Day/Night (ICR)

•

Micro SD support

•

BNC analog output

3

1.2 Package Contents

The HD WDR IP Camera’s standard package contains the items as shown below. Contents will vary among different models. Please check the list as follows for details.

HD WDR IP Camera Back focus adjuster

Quick Guide

Power terminal block

CD

(bundled software and documentation)

4

2. Introduction of IP Camera

This chapter will provide the camera dimensions for reference before installation.

Definition of each connector on the camera’s rear board will also be specified.

2.1 Camera Dimensions

The IP Camera’s dimensions are as shown below:

5

2.2 Connectors on the Rear Board

The diagram below shows the IP Camera’s rear board. Definition for each connector will be given as follows.

Network LEDs

NETWORK VIDEO

LINE

OUT

LINE IN

MIC IN

Reset Button

Power Connector

Power LED

AUTO

IRIS

PoE

I/O 1 2 3 4

SD

DC 12V/AC 24V

6

Line Out & Line In / Mic In ports

For two-way audio transmission

Power LED

Green light indicates good power connection.

Reset Button

Press and hold the button for 5 seconds, and then the camera will reset to factory defaults. After around 30 seconds, reconnect the camera by entering its default IP address: 192.168.0.250, in the URL bar.

Auto Iris Lens Connector

For use with auto iris lens

Network (with PoE) Connector

RJ45 connector for LAN connection

Network LEDs

Green Link Light indicates good network connection.

Orange Activity Light flashes for network activity indication.

K OR TW NE

I/O Terminal Connector

For alarm connection (see section 3.2 Installation

—

Alarm Application )

BNC Connector

For video output

Micro SD Card Slot

For video and snapshots storage

AC 24V/DC 12V Connector

Please refer to the table below for wiring of AC 24V and DC 12V camera with the supplied power cable.

＋

AC 24V: Power-1 DC 12V: Power

AC 24V: Earth GND DC 12V: Reserved

－

AC 24V: Power-2 DC 12V: GND

7

3. Preparations for IP Camera Setup

This chapter outlines information about system requirements for IP Camera operation, procedures of camera connection, and login to the camera.

3.1 System Requirements

To perform the IP Camera via web browser, please ensure your PC is in good network connection, and meet system requirement as described below.

Items System Requirement

Personal Computer

1. Intel Pentium M, 2.16 GHz or Intel Core

TM

2 Duo,

2.0 GHz

2. 2 GB RAM or more

Operating System

Web Browser

Network Card

Viewer

Windows VISTA or Windows XP

Microsoft Internet Explorer 6.0 or later

10Base-T (10 Mbps) or 100Base-TX (100 Mbps) operation

ActiveX control plug-in for Microsoft IE

3.2 Installation

Please follow the instructions below to complete IP Camera installation.

Lens Mounting: CS Mount Lens

Power Connection

Please refer to section 2.2 Connectors on the Rear Board for power wiring.

Additionally, if using PoE, make sure Power Sourcing Equipment (PSE) is in use in the network.

Ethernet Cable Connection

Use of Category 5 Ethernet cable is recommended for network connection; to have best transmission quality, cable length shall not exceed 100 meters.

Connect one end of the Ethernet cable to the RJ-45 connector of the IP Camera, and the other end of the cable to the network switch or PC.

NOTE: In some cases, you may need use an Ethernet crossover cable when connecting the IP Camera directly to the PC.

8

Check the status of the link indicator and activity indicator LEDs; if the LEDs are unlit, please check LAN connection.

Green Link Light indicates good network connection.

Orange Activity Light flashes for network activity indication.

K OR TW NE

Alarm Application

The camera equips one alarm input and one relay output for alarm application.

Refer to alarm pin definition below to connect alarm devices to the IP Camera if needed.

1. Output+

2. Output-

3. Input+

4. Input-

9

3.3 Accessing IP Camera

For initial access to the IP Camera, users can search the camera through the installer program: DeviceSearch.exe, which can be found in “DeviceSearch” folder in the supplied CD.

Device Search Software Setup

Step 1: Double click on the program Device Search.exe (see the icon below); its window will appear as shown below. Then click the “Device Search” button.

Step 2: The security alert window will pop up. Click “Unblock” to continue.

10

Device Search

Step 3: Click “Device Search” again, and all the finding IP devices will be listed in the page, as shown in the figure below. The IP Camera’s default IP address is: 192.168.0.250.

Step 4: Double click or right click and select “Browse” to access the camera directly via web browser.

Step 5: Then the prompt window of request for entering default username and password (as shown below) will appear for login to the IP Camera.

The default login ID and password for the Administrator are:

11

Login ID

root

Password

NOTE: ID and password are case sensitive.

NOTE: It is strongly advised that administrator’s password be altered for the security concerns. Refer to section 4.3.2

Security for further details.

Additionally, users can change the IP Camera’s network property, either DHCP or Static IP directly in the device finding list. Refer to the following section for changing the IP Camera’s network property.

Example of Changing IP Camera’s Network Property

Users can directly change an IP Camera’s network property, ex. from static IP to DHCP, in the finding device list. The way to change the IP Camera’s network property is specified below:

Step 1: In the finding device list, click on the IP Camera that you would like to change its network property. On the selected item, right click and select

“Network Setup.” Meanwhile, record the IP Camera’s MAC address, for future identification.

Step 2: The “Network Setup” page will come out. Select “DHCP,” and press

“Apply” button down the page.

12

Step 3: Click “OK” on the Note of setting change. Wait for one minute to re-search the IP Camera.

Step 4: Click the “Device Search” button to re-search all the devices. Then select the IP Camera with the correct MAC address. Double click on the

IP Camera, and the login window will come out.

Step 5: Enter User name and Password to access the IP Camera

13

Using recording software

The product software CD also contains recording software-IP CamSecure, allowing simultaneous monitoring and video recording for multiple Network Cameras .

Please install the recording software; then launch the program to add the Network Camera to the

Channel list .

For detailed information about how to use IP CamSecure, please refer to the user’s manual of the software or download it at http://global.level1.com.

14

Installing DC Viewer Software Online

For the initial access to the IP Camera, a client program, DC Viewer, will be automatically installed to your PC when connecting to the IP Camera.

If the Web browser doesn’t allow DC Viewer installation, please check the

Internet security settings or ActiveX controls and plug-ins settings (see

15

16

Appendix B: Internet Security Settings ) to continue the process.

The Information Bar (just below the URL bar) may come out and ask for permission to install the ActiveX Control for displaying video in browser (see the figure below). Right click on the Information Bar and select “Install ActiveX

Control…” to allow the installation.

Then the security warning window will pop up. Click “Install” to carry on software installation.

Click “Finish” to close the DC Viewer window when download is finished. For the detailed software download procedure, please refer to Appendix C: DC

Viewer Download Procedure .

Once login to the IP Camera, users will see the Home page as shown below:

NOTE: Please note that the function buttons will vary depending on the camera model.

Administrator/User Privileges

“Administrator” represents the person who can configure the IP Camera and authorize users access to the camera; “User” refers to whoever has access to the camera with limited authority, i.e. entering Home and Camera setting pages.

Image and Focus Adjustment

The image displays on the Home page when successfully accessing to the IP

Camera. Adjust zoom and focus as necessary to produce a clear image.

17

4. Configuration & Operation

The IP Camera is provided with a user-friendly browser-based configuration interface, and a free bundled IP CamSecure Lite for record and playback video.

In this chapter, information about main page introduction, system related settings and camera settings will be described in detail.

For further information about IP CamSecure, please refer to IP CamSecure user manual.

4.1 Browser-based Viewer Introduction

The figure below shows the main page of the IP Camera user interface.

Time Display

Live Video Panel

Video Format Selection

Display Mode

Recording Button

Video Compression Info

Video Stream Pause Button

Snapshot Button

Speaker Button

Talk Button

NOTE: Please note that the function buttons will vary depending on the camera model.

There are five tabs: Home, System, Streaming, Camera and Logout on the top of the viewer.

Home

Users can monitor live video of the targeted area.

18

System setting

Administrator can set host name, system time, root password, network related settings, etc. Further details will be interpreted in section 4.3 System Related

Settings .

Streaming setting

Administrator can modify video resolution and rotate type and select audio compression mode in this page.

Camera setting

Users can adjust various camera parameters, including <Exposure>, <White

Balance>, <Brightness>, <Sharpness>, <Contrast> and <Digital Zoom>.

Logout

Click on the tab to re-login the IP Camera with another username and password.

4.2 Home Page

In the Home page, there are several function buttons right down the displayed image.

19

20

NOTE

:

Please note that the function buttons will vary depending on the camera model.

Screen Size Adjustment

Image display size can be adjusted to x1/2 and full screen.

Digital Zoom Control

In the full screen mode, users can implement digital zoom by rotating the mouse wheel (for zoom in/out) and dragging the mouse into any direction.

Talk button

(on/off)

Talk function allows the local site to talk to the remote site. Click on the button to switch it to on/off. Please refer to section 4.3.2 Security : Add user >>

Talk/Listen for f ur ther details. This function is only open to “User” who has been granted this privilege by the Administrator.

NOTE: This function is only available for the Box Camera and Vandal

Proof IP Dome.

Speaker button

(on/off)

Press the Speaker button to mute/activate the audio.

NOTE: This function is only available for the Box Camera and Vandal

Proof IP Dome.

Snapshot button

Press the button, and the JPEG snapshots will automatically be saved in the appointed place. The default place of saving snapshots is: C:\. To change the storage location, please refer to section 4.3.11 File Location for further details.

Video Streaming Pause/Restart button

(pause/restart)

Press the pause button to disable video streaming, the live video will be displayed as black. Press the restart button to show the live video again.

Recording button

(on/off)

Press the button and the recordings from the Live View will be saved to the location specified in the “File Location” (snapshot) page; see section 4.3.11

File Location for further details.

4.3 System Related Settings

The figure below shows all categories under the “System” tab. Each category in the left column will be explained in the following sections.

NOTE

:

The “System” configuration page is only accessible by

Administrator

.

21

4.3.1 Host Name and System Time Setting

Press the first category: <System> in the left column; the page is shown as below.

22

Host Name

The name is for camera identification. If alarm function (see section 4.3.7

Application ) is enabled and is set to send alarm message by Mail/FTP, the host name entered here will display in the alarm message.

Time Zone

Select the time zone you are in from the drop-down menu.

Enable Daylight Saving Time (DST)

To enable DST, please check the item and then specify time offset and DST duration. The format for time offset is [hh:mm:ss]; for instance, if the amount of time offset is one hour, please enter “01:00:00” into the field.

Sync With Computer Time

Select the item, and video date and time display will synchronize with the PC’s.

Manual

The Administrator can set video date, time and day manually. Entry format should be identical with that shown next to the enter field.

Sync with NTP Server

Network Time Protocol (NTP) is an alternate way to synchronize your camera’s clock with a NTP server. Please specify the server you wish to synchronize in the enter field. Then select an update interval from the drop-down menu. For further information about NTP, please see the web site: www.ntp.org

.

4.3.2 Security

Click the category: <Security>, and the page is shown as the figure below.

Root password

Change the administrator’s password by inputting the new password in both text boxes. The input characters/numbers will be displayed as dots for security purposes. After clicking <Save>, the web browser will ask the Administrator for the new password for access. The maximum length of the password is 14 digits.

23

NOTE: The following characters are valid: A-Z, a-z, 0-9, !#$%&’-.@^_~.

Add user

Type the new user's name and password and click <Add> to add the new user.

Both user name and password can be up to 16 characters. The new user will be displayed in the user name list. There is a maximum of twenty user accounts.

Each user can be assigned the privileges of “Camera control”, “Talk” and

“Listen”.

•

I/O access

This item supports fundamental functions that enable users to view video when accessing to the camera.

•

Camera control

This item allows the appointed User to change camera parameters on the Camera Setting page.

•

Talk/Listen

Talk and Listen functions allow the appointed user in the local site (PC site) communicating with, for instance, the administrator in the remote site.

NOTE: The Compact IP Dome does not have Talk function.

Manage User

Delete user

To delete a user, pull down the user list, and select the user name you wish to delete. Then click <Delete> to remove it.

Edit user

Pull down the user list and select a user name. Click <Edit> to edit the user’s password and privilege.

NOTE: It is required to enter the User password as well as select the function open to the user. When finished, click <Save> to modify the account authority.

24

25

4.3.3 Network

Click <Network> in the left column, and the page will display as shown below.

26

Users can choose to connect to the IP Camera with fixed or dynamic (DHCP) IP address. The IP Camera also provides PPPoE support for users who connect to the network via PPP over Ethernet (PPPoE).

Get IP address automatically (DHCP)

The camera’s default setting is “Use fixed IP address”. Please refer to the previous section

3.3 Accessing IP Camera for login with the default IP address.

If select “Get IP address automatically”, after the IP Camera restarts, users can search it through the installer program: DeviceSearch.exe, which can be found in “DeviceSearch” folder in the supplied CD.

NOTE: Please make the record of the IP Camera’s MAC address, which can be found in the label of the camera, for identification in the future.

Use fixed IP address

To setup static IP address, select “Use fixed IP address” and move the cursor to the IP address blank (as indicated below) and insert the new IP address, ex.

192.168.7.123; then go to the Default gateway (explained latter) blank and change the setting, ex. 192.168.7.254. Press “Save” to confirm the new setting.

When using static IP address to login to the IP Camera, users can access it either through “DeviceSearch” software (see 3.3 Accessing IP Camera ) or input the IP address in the URL bar and press “Enter”.

27

28

•

IP address

This is necessary for network identification.

•

Subnet mask

It is used to determine if the destination is in the same subnet. The default value is “255.255.255.0”.

•

Default gateway

This is the gateway used to forward frames to destinations in different subnet. Invalid gateway setting will fail the transmission to destinations in different subnet.

•

Primary DNS

Primary DNS is the primary domain name server that translates hostnames into IP addresses.

•

Secondary DNS

Secondary DNS is a secondary domain name server that backups the primary DNS.

Use PPPoE

For the PPPoE users, please enter the PPPoE Username and Password into the fields, and click on the “Save” button to complete the setting.

Advanced

•

Web Server port

The default web server port is 80. Once the port is changed, the user must be notified the change for the connection to be successful. For instance, when the Administrator changes the HTTP port of the IP

Camera whose IP address is 192.168.0.100 from 80 to 8080, the user must type in the web browser “http://192.168.0.100:8080” instead of

“http://192.168.0.100”.

•

RTSP port

RTSP port could be set from 1 to 65535. (Normal Setting Port: 554,

1024 ~65535)

•

MJPEG over HTTP port

The default setting of HTTP Port is 8008; setting range: 1024 ~65535.

NOTE: Be aware to choose the different port from the one set for the web server port.

UPnP Setting

•

Enable UPnP

When the UPnP is enabled, whenever the IP Camera is presented to the LAN, the icon of the connected IP Camera will appear in My

Network Places to allow for direct access as shown below.

29

FCS-1131

FCS-1131

FCS-1141

FCS-3071

30

NOTE: To enable this function, please make sure the UPnP component is installed on your computer. Please refer to

Appendix E: Install UPnP Components for UPnP component installation procedure.

•

Enable UPnP port forwarding

When the UPnP port forwarding is enabled, the IP Camera is allowed to open the web server port on the router automatically.

NOTE: To enable this function, please make sure that your router supports UPnP and it is activated.

•

Friendly name

Set the name for the IP Camera for identity.

4.3.4 DDNS

Dynamic Domain Name System (DDNS) allows a host name to be constantly synchronized with a dynamic IP address. In other words, it allows those using a dynamic IP address to be associated to a static domain name so others can connect to it by name.

31

Enable DDNS

Check the item to enable DDNS.

Provider

Select one DDNS host from the provider list.

Host name

Enter the registered domain name in the field.

Username/E-mail

Enter the username or e-mail required by the DDNS provider for authentication.

Password/Key

Enter the password or key required by the DDNS provider for authentication.

4.3.5 Mail

The Administrator can send an e-mail via Simple Mail Transfer Protocol (SMTP) when an alarm is triggered. SMTP is a protocol for sending e-mail messages

32

between servers. SMTP is a relatively simple, text-based protocol, where one or more recipients of a message are specified and the message text is transferred.

The configuration page is shown as follows:

Two sets of SMTP can be configured. Each set includes SMTP Server, Account

Name, Password and E-mail Address settings. For SMTP server, contact your network service provider for more specific information.

4.3.6 FTP

The Administrator can set as sending alarm message to a specific File Transfer

Protocol (FTP) site when an alarm is triggered. Users can assign alarm message to up to two FTP sites. The FTP setting page is shown below. Enter the FTP details, which include server, server port, user name, password and remote folder, in the fields. Press “Save” when finished.

33

4.3.7 Application (Excluding Compact IP Dome)

The IP Camera (Box Camera and Vandal Proof Dome) equips one alarm input and one relay output for cooperating with alarm system to catch events’ images.

Refer to alarm pin definition below to connect alarm devices to the IP Camera if needed. The alarm configuration page is also shown below.

Alarm Pin Definition

34

1. Output+

2. Output-

3. Input+

4. Input-

Alarm Switch

The Administrator can enable or disable the alarm function.

Alarm Type

Select an alarm type, “Normal close” or “Normal open,” that corresponds with the alarm application.

Alarm Output

Define alarm output signal “high” or “low” as the normal alarm output status according to the current alarm application.

Triggered Action (Multi-option)

The Administrator can specify alarm actions that will take when the alarm is triggered. All options are listed as follows:

35

•

Enable Alarm Output

Select the item to enable alarm relay output.

•

Send Alarm Message by FTP/E-Mail

The Administrator can select whether to send an alarm message by FTP and/or E-Mail when an alarm is triggered.

•

Upload Image by FTP

Select this item, and the Administrator can assign a FTP site and configure various parameters as shown in the figure below. When the alarm is triggered, event images will be uploaded to the appointed FTP site.

36

•

Record Stream to SD Card

Select the item, and the alarm-triggered recording will be saved into your

Micro SD card.

NOTE: Please make sure the local recording (with Micro SD/

SDHC card) is activated so that this function can be implemented.

See section 4.3.10 Recording for further details.

•

Upload Image by E-Mail

Select this item, and the Administrator can assign an e-mail address and configure various parameters as shown in the figure below. When the

37

alarm is triggered, event images will be sent to the appointed e-mail address.

38

NOTE: Make sure SMTP or FTP configuration has been completed. See section 4.3.5 Mail and 4.3.6 FTP for further details.

File Name

Enter a file name in the blank, ex. image.jpg. The uploaded image’s file name format can be set in this section. Please select the one that meets your requirements.

•

Add date/time suffix

File name: imageYYMMDD_HHNNSS_XX.jpg

Y: Year, M: Month, D: Day

H: Hour, N: Minute, S: Second

X: Sequence Number

•

Add sequence number suffix (no maximum value)

File name: imageXXXXXXX.jpg

X: Sequence Number

•

Add sequence number suffix (limited value)

File Name: imageXX.jpg

X: Sequence Number

The file name suffix will end at the number being set. For example, if the setting is up to “10,” the file name will start from 00, end at 10, and then start all over again.

•

Overwrite

The original image in the FTP site will be overwritten by the new uploaded file with a static filename.

Save

After complete all the settings mentions above, please click on the Save button to save all the settings in this page.

39

4.3.8 Motion Detection

Motion Detection function allows detecting suspicious motion and triggering alarms when motion volume in the detected area reaches/exceeds the determined sensitivity threshold value.

40

In the Motion Detection setting page, there is a frame (Motion Detection

Window) displayed on the Live Video Pane. The Motion Detection Window is for defining the motion detection area. To change the size of the Motion

Detection Window, move the mouse cursor to the edge of the frame and draw it outward/inward. Moving the mouse to the center of the frame can shift the frame to the intended location.

Up 10 Motion Detection Windows can be set. Press the “add” button under the

Live Video Pane to add a Motion Detection Window. To cancel a Motion

Detection Window, move the mouse cursor to the selected Window, and click on the “delete” button.

If Motion Detection function is activated, the pop-off window (Motion) with indication of motion will be shown.

When motion is detected, the signals will be displayed on the Motion window as shown below.

Detailed settings of Motion Detection are described as follows:

Motion Detection

You will be able to turn on/off Motion Detection in System section. Default setting is Off.

Motion Detection Setting

Users could adjust various parameters of Motion Detection in this section.

•

Sampling pixel interval [1-100]:

The default value is 10, which means system will take one sampling pixel for every 10 pixel.

•

Detection level [1-100]:

The default level is 10. The item is to set detection level for each sampling pixel; the smaller the value, the more sensitive it is.

41

42

•

Sensitivity level [1-100]:

The default level is 80, which means if 20% or more sampling pixels are detected differently, system will detect motion. The bigger the value, the more sensitive it is. Meanwhile, when the value is bigger, the red horizontal line in the motion indication window will be lower accordingly.

•

Time interval (sec) [0-7200]:

The default interval is 10. The value is the interval between each detected motion.

Triggered Action (Multi-option)

The Administrator can specify alarm actions that will take when motion is detected. All options are listed as follows:

•

Enable Alarm Output

Check the item and select the predefined type of alarm output to enable alarm relay output when motion is detected.

NOTE: This option is excluded in the Compact IP Dome

Camera.

•

Record stream to SD Card

Select this item, and the Motion Detection recording will be stored in

Micro SD/ SDHC card when motion is detected.

NOTE: Please make sure the local recording (with Micro SD/

SDHC card) is activated so that this function can be implemp-

lemented. See section 4.3.10 Recording for further details.

•

Send Alarm Message by FTP/E-Mail

The Administrator can select whether to send an alarm message by

FTP and/or E-Mail when motion is detected.

•

Upload Image by FTP

Select this item, and the Administrator can assign a FTP site and configure various parameters as shown in the figure below. When motion is detected, event images will be uploaded to the appointed FTP site.

•

Upload Image by E-Mail

Select this item, and the Administrator can assign an e-mail address and configure various parameters as shown in the figure below. When motion is detected, event images will be sent to the appointed e-mail address.

NOTE: Make sure SMTP or FTP configuration has been completed. See section 4.3.5 Mail and 4.3.6 FTP for further details.

File Name

The uploaded image’s filename format can be set in this section. Please select the one that meets your requirements.

Save

Click the Save button to save all the Motion Detection settings mentioned above.

43

4.3.9 Storage Management

Users can implement local recording to the Micro SD/SDHC card.

NOTE: Please format the Micro SD/SDHC card first before recording starts.

44

Device information

If a Micro SD/SDHC card is installed, the card information such as the memory capacity and status will be shown at Device Information section.

Device setting

Press the “Format” button to format the memory card.

Disk cleanup setting

Users can enable automatic recordings cleanup by specifying the time and storage limits

Recording List

Each video file on the Micro SD/SDHC card will be listed in the Recording list as shown below.

•

Remove

To remove a file, select the file first, and then press the “Remove” button.

•

Sort:

Press the “Sort” button, and the files in the Recording list will be listed in name and date order.

NOTE: The capital letter A/M/R appears in the very beginning of a file name denotes the sort of the recording: A stands for Alarm,

M stands for Motion, and R stands for regular recording.

•

Download:

To open/download a video clip, select the file first, and then press the

“download” button below the Recording list field. The selected file window will pop up as shown below. Click on the AVI file to directly play the video in the player or download it to a specified location.

45

4.3.10 Recording

In the Recording setting page, users can specify the recording schedule that fits the present surveillance requirement.

46

Activating Micro SD/SDHC Card Recording

Two types of schedule mode are offered: Always and Time Frame setting.

Users can setup the time frame to fit the recording schedule or choose “Always” to activate Micro SD/SDHC Card Recording all the time.

Please click on the “Save” button for confirming the schedule mode.

Terminating Micro SD/SDHC Card Recording

Select “Disable” to terminate the recording function.

4.3.11 File Location

Users can specify a storage location for the snapshots and recording. The default setting is: C:\. Once confirm the setting, press “Save,” and all the snapshots and recording will be saved in the designate location.

NOTE: Please make sure the selected file path contains valid characters such as letters and numbers.

47

48

4.3.12 Iris Adjustment (Excluding Compact IP Dome)

For users who use Auto-iris lens, when it is required to implement iris adjustment, please refer to the Iris adjustment procedure in the setting page to adjust iris.

4.3.13 View Log File

Click on the link to view the system log file. The content of the file provides useful information about configuration and connections after system boot-up.

49

4.3.14 View User Information

The Administrator can view each added user’s login information and privileges

(see 4.3.2 Security ).

View User Login Information

All the users in the network will be listed in the “User information” zone, as shown below. As the figure below shows:

root:

It indicates that one user’s login username is: root, and password is blank .

50

View User Privilege

Press “get user privacy” down the page, and the Administrator can view each user’s privileges.

As the figure above shows:

User: 1:1:0:1

1:1:0:1= I/O access: Camera control: Talk: Listen (see 4.3.2 Security )

Therefore, it denotes the user is granted privileges of I/O access, Camera control and Listen.

51

4.3.15 View Parameters

Click on this item to view the entire system’s parameter setting.

52

4.3.16 Factory Default

The factory default setting page is as shown below. Follow the instructions to reset the IP camera to factory default setting if needed.

Set Default

Click on the “Set Default” button to recall the factory default settings. Then the system will restart in 30 seconds.

NOTE: The IP address will be restored to default.

Reboot

Click on the “Reboot” button, and the system will restart without changing the current settings.

53

54

4.3.17 Software Version

The software version of the IP Camera is displayed in the software version page, which is shown below.

4.3.18 Software Upgrade

Software upgrade can be carried out in the “Software Upgrade” page as shown below.

NOTE: Make sure the upgrade software file is available before carrying out software upgrade.

The procedure of software upgrade is like the following:

55

Step 1: Click “Browse” and select the binary file to be uploaded, ex.

Userland.jffs2.

56

NOTE: Do not change the upgrade file name, or the system will fail to find the file.

Step 2: Pull down the upgrade binary file list and select the file you want to upgrade; in this case, select “userland.jffs2.”

Step 3: Press “Upgrade”. The system will first check whether the upgrade file exists or not, and then begin to upload the upgrade file. Subsequently, the upgrade status bar will display on the page. When it runs to 100%, the upgrade process is finished.

After the upgrade process is finished, the viewer will return to Home page.

Step 4: Close the video browser.

Step 5: Click “Control Panel”, and then double click “Add or Remove

Programs.” In the “Currently install programs” list, select “DCViewer” and click the button “Remove” to uninstall the existing DC Viewer.

Step 6: Open a new web browser, re-login the IP Camera, and then allow the automatic download of DC Viewer.

57

4.3.19 Maintenance

Users can export configuration files to a specified location and retrieve data by uploading an existing configuration file to the IP Camera.

58

Export

Users can save the system settings by exporting the configuration file (.bin) to a specified location for future use. Press the “Export” button, and the popup File

Download window will come out as shown below. Click “Save” and specify a desired location for saving the configuration file.

Upload

To copy an existing configuration file to the IP Camera, please first click on

“Browse” to select the configuration file, and then press the “Upload” button for uploading.

4.4 Video and Audio Streaming Settings

Press the tab ”Streaming” in the top of the page, and the configurable video and audio items will display in the left column. In Streaming, the Administrator can configure specific video resolution, video compression mode, video protocol, audio transmission mode, etc. Further details of these settings will be specified in the following sections.

4.4.1 Video Resolution and Rotate Type

The video setting page is shown below:

59

60

Video Format

The IP Camera provides various video dual streaming formats like the following:

•

MJPEG + H.264

•

MJPEG + MPEG-4

•

MJPEG + BNC

•

H.264 + H.264

•

H264 + BNC

Resolution for MJPEG & H.264 format includes:

•

1280 x 960 (CCD)

•

HD 720p: 1280

×

720 (25/30fps)

•

D1: 720

×

480 (25/30fps)

•

VGA: 640

×

480 (25/30fps)

•

QVGA: 320

×

240 (25/30fps)

•

CIF: 352

×

240 (25/30fps)

•

QCIF: 176

×

144 (25/30fps)

Click “Save” to confirm the Video Format setting.

Text Overlay Settings

Users can select the items to display data including date/time/text on the live video pane. The maximum length of the string is 20 alphanumeric characters

Click “Save” to confirm the Text Overlay setting.

Video Rotate Type

Users can change video display type if necessary. Selectable video rotate types include Normal, Flip, Mirror and 180 degree. Differences among these types are illustrated as below.

Suppose the displayed image of IP camera is shown as the figure below.

To rotate the image, users can select “Flip”, for instance. Then the displayed image will be reversed as shown below.

The following is descriptions for different video rotate type.

•

Flip

If select <Flip>, the image will be rotated vertically.

•

Mirror

If select <Mirror>, the image will be rotated horizontally.

•

180 Degree

Selecting <180 Degree> will make the image 180

°

counter-/clockwise inversed.

Click “Save” to confirm the setting.

GOV Settings

Users can set the GOV length to determine the frame contracture (I-frames and

P-frames) in a video stream for saving bandwidth. Longer GOV means decreasing the frequency of I-frames.

Click “Save” to confirm the GOV setting.

61

4.4.2 Video Compression

Users can select a proper MJPEG/H.264/MPEG-4 compression mode in the video compression page (see the figure below), depending on the surveillance applications.

62

Users can also decide whether to display compression information on the Home page.

Click “Save” to confirm the video compression settings.

CBR Mode Setting

The CBR (Constant Bit Rate) mode could be the preferred bit rate mode if the bandwidth available is limited. It is important to take account of image quality while choosing to use the CBR mode.

63

4.4.3 Video OCX Protocol

In the Video OCX protocol setting page, users can select RTP over UDP, RTP over TCP, RTSP over HTTP or MJPEG over HTTP, for streaming media over the network. In the case of multicast networking, users can select the Multicast mode. The page is shown as follows.

64

Video OCX protocol setting options include:

•

RTP over UDP / RTP over RTSP(TCP) / RTSP over HTTP / MJPEG over HTTP

Select a mode according to your data delivery requirements.

•

Multicast Mode

Enter all required data, including multicast IP address, MPEG-4 video port, H.264 video port, MJPEG video port, audio port and TTL into each blank.

Click “Save” to confirm the setting.

4.4.4 Video Frame Skip

Video frame skipping is for saving bandwidth, if necessary. The setting page is shown below.

MJPEG/H.264/MPEG-4 Frame Skip options include:

•

No skipping, default

•

Frame skipping at 2 frame internal

•

Frame skipping at 5 frame internal

•

Frame skipping to 1 frame (highest frame loss rate)

NOTE: Higher frame skipping rate will decrease video smoothness.

65

4.4.5 Video Mask

There are up to five video masks can be set by users.

66

Active Mask Function

•

Add A Mask

Check a Video Mask checkbox, and a red frame will come out in the Live

Video pane at the right side. Use the mouse to drag and drop to adjust the mask’s size and place it on the target zone.

NOTE: It is suggested to set the Video Mask twice bigger than the object.

•

Cancel a mask

Uncheck the checkbox of the Video Mask meant to be deleted, and the selected mask will disappear from the Live Video pane instantly.

Mask Setting

•

Mask color

The selections of Mask color include red, black, white, yellow, green, blue, cyan, and magenta.

•

Type

Select to change the mask type as solid or transparent.

4.4.6 Audio Mode and Bit Rate Settings

The audio setting page is shown below. In the Audio page, the Administrator can select one transmission mode and audio bit rate.

Transmission Mode

•

Full-duplex (Talk and Listen simultaneously)

In the Full-duplex mode, the local and remote sites can communicate with each other simultaneously, i.e. both sites can speak and be heard at the same time.

67

68

NOTE: This option is only available in Box Camera and Vandal

Proof Dome.

•

Half-duplex (Talk or Listen, not at the same time)

In the Half-duplex mode, the local/remote site can only talk or listen to the other site at a time.

NOTE: This option is only available in Box Camera and Vandal

Proof Dome.

•

Simplex (Talk only)

In the Talk only Simplex mode, the local/remote site can only talk to the other site.

NOTE: This option is only available in Box Camera and Vandal

Proof Dome.

•

Simplex (Listen only)

In the Listen only Simplex mode, the local/remote site can only listen to the other site.

•

Disable

Select the item to turn off the audio transmission function.

Server Gain Setting

Set the audio input/output gain levels for sound amplification. The audio gain values are adjustable from 1 to 6. The sound will be turned off if the audio gain is set to “Mute”.

Bit Rate

Selectable audio transmission bit rate include 16 kbps (G.726), 24 kbps (G.726),

32 kbps (G.726), 40 kbps (G.726), uLAW (G.711) and ALAW (G.711). Both uLAW and ALAW signify 64 kbps but in different compression formats. Higher bit rate will let higher audio quality and require bigger bandwidth.

Click “Save” to confirm the setting.

4.5 Camera Settings

The figure below is the camera configuration page. Details of each parameter setting are described in the following subsections.

NOTE: Camera settings and function buttons will vary depending on the camera model.

69

4.5.1 Exposure Setting

The Exposure pull-down menu is shown as follows:

70

The exposure is the amount of light received by the image sensor and is determined by the width of lens diaphragm opening (iris adjustment), the amount of exposure by the sensor (shutter speed) and other exposure parameters. With this item, users can define how the Auto Exposure function works.

Each exposure mode is specified as follows:

Full Auto Mode

In this mode, the camera’s Shutter Speed, IRIS and AGC (Auto Gain Control) control circuits work together automatically to get consistent video output level.

The minimum shutter speed range is from 1 to 1/30 sec. (NTSC) and from 1 to

1/25 sec. (PAL) with 6 options. Users could select suitable shutter speed according to the environmental illumination.

NOTE: The minimum shutter speed set in the Full Auto Mode will be applied to Full Auto Flickerless Mode and Auto Iris Mode.

Full Auto Flickerless Mode

Television scanning (PAL & NTSC) and power supply systems (AC 50 & 60 Hz) are not the same in different countries and regions. Users might find flickering situation displayed on the screens because the devices are working under different frequency systems. With Auto Flickerless function, users could reduce the symptom.

NOTE: The minimum shutter speed will vary depending on the setting in

Full Auto Mode.

Auto Iris

In this mode, the exposure gives priority to the auto iris. Shutter speed and AGC circuit will function automatically in cooperating with IRIS to get consistent exposure output.

NOTE: The minimum shutter speed will vary depending on the setting in

Full Auto Mode.

Manual Mode

In this mode, users can select a number between 1 and 15; bigger number means slower shutter. Once change the value, please press <SET> to confirm the new setting.

Fixed Shutter Mode

In this mode, fixed shutter speed could be selected from the dropdown menu.

The shutter speed range is from 1 to 1/10000 sec. with 16 options. Users could select suitable shutter speed according to the environmental illumination.

4.5.2 White Balance Setting

The White Balance pull-down menu is shown as follows:

A camera needs to find reference color temperature, which is a way of measuring the quality of a light source, for calculating all the other colors. The unit for measuring this ratio is in degree Kelvin (K). Users can select one of the

White Balance Control modes according to the operating environment. The following table shows the color temperature of some light sources for reference.

71

Light Sources

Cloudy Sky

Noon Sun and Clear Sky

Household Lighting

75-watt Bulb

Color Temperature in K

6,000 to 8,000

6,500

2,500 to 3,000

2,820

Candle Flame 1,200 to 1,500

Auto Mode

The Auto Balance White mode is suitable for environment with light source having color temperature ranging from 3200 ~ 7600K.

Indoor/outdoor Mode

Select for indoor or outdoor mode.

Manual Mode

In this mode, users can change the White Balance value manually. Users can select a number between 1 ~ 11, and press <SET> to confirm the new setting.

4.5.3 Backlight Setting

Based on various lighting situations, users could select to turn on or off the function of backlight compensation to optimize the video quality. The default value of Backlight is Off.

4.5.4 Brightness Setting

Users can adjust the image’s brightness by adjusting the item. To increase video brightness, select a bigger number. Press <SET> to confirm the new setting.

72

4.5.5 Sharpness Setting

Increasing the sharpness level can make the image looked sharper; especially enhance the object’s edge. Press <SET> to confirm the new setting.

4.5.6 Contrast Setting

Camera image contrast level is adjustable, ranging from 1 to 11.

4.5.7 Saturation Setting

Camera image saturation level is adjustable; please select ranging from 1 to 11.

4.5.8 Digital Zoom Setting

The camera’s digital zoom is adjustable from x1 to x16. Press <SET> to confirm the new setting.

4.5.9 IR Function

With the IR cut filter, the IP Camera can still catch clear image at night time or in low light conditions. Press <SET> to confirm the new setting.

73

4.5.10 WDR Function

The Wide Dynamic Range (WDR) function is for solving high contrast or changing light issues so that enhances better video display. The WDR is adjustable from level 1 to 4. Higher level of WDR represents wider dynamic range, so that he IP Camera can catch a greater scale of brightness.

Press <SET> to confirm the new setting.

4.5.11 3DNR Function

With 3D Noise Reduction (3DNR) function, the IP Camera can deliver more clear images in low-light conditions.

4.5.12 TV System Setup

Select the video format that matches the present TV system.

74

4.6 Logout

Press the tab “Logout” in the top of the page, and the login window will pop up.

This enables login with another user name.

75

Appendix A: Technical Specifications

Camera

Image Sensor

Picture Elements

Minimum Illumination

Color

B/W

Shutter Speed

White Balance

Lens

Lens Mount

Operation

Video Compression

Video Streaming

Resolution

Frame Rate

Image Setting

Audio

Alarm

1/3" Sony Progressive CCD

1280(H) x 960 (V)

0.03 lux @ F1.2

0.001 lux @ F1.2

1~ 1/10000 sec.

Manual / ATW (1500 ~ 15000K)

CS mount Lens

H.264

MJPEG

MPEG-4

Brightness

Exposure

Backlight

Sharpness

Contrast

White Balance

Digital Zoom

Image Rotation

WDR

3D Noise Reduction

Privacy Mask

Privacy Mask Type

ICR (Optional)

Two-way Audio

Compression

Input

H.264 Baseline / MJPEG / MPEG-4

Simultaneously, H.264 + MJPEG

Simultaneously, MPEG-4 + MJPEG

Simultaneously, MJPEG + BNC

Simultaneously, H.264 + H.264

Simultaneously, H.264 + BNC

1280 x 960 / HD 720p / D1 / VGA / QVGA / CIF / QCIF

1280 x 960 / HD 720p / D1 / VGA / QVGA / CIF / QCIF

1280 x 960 / HD 720p / D1 / VGA / QVGA / CIF / QCIF

1280 x 960 @ 12.5/15 fps, 720p @ 25/30 fps

Manual

Auto / Manual / Fixed Shutter

On / Off

Manual

Manual

Auto / Manual / Indoor / Outdoor

1x ~ 16x

Flip, Mirror, and 180

∘

Rotate

Off / 4 Level Adjustment

On / Off

On / Off

Mosaic, Transparent, Color

Auto / On / Off

Line out, Line in / Mic in

G.711 / G.726

5V 10k Ω pull up

76

Output

Network

Interface

Protocol

Password Levels

Internet Browser

User Account

Mechanical

Connectors

LED Indicator

General

Operating Temperature

Power

Ethernet

Micro SD

Audio

Alarm

Auto Iris

Analog Video

Power Source

Power Consumption

Certificate

Dimension

Weight

Photo relay output 300VDC/AC

10/100 Mb Ethernet (RJ-45)

TCP/IP, UDP, RTP, RTSP, HTTP, ICMP, FTP, SMTP, DHCP and IGMP

User and Administrator

Internet Explorer (6.0+)

20

3 pins terminal block

RJ-45

SDHC support

Stereo phone jack,

∅

3.5mm

4 pins terminal block

DC drive

1.0 Vp-p / 75 Ω , BNC

Power, Link, ACT

0°C ~ 50°C

Humidity: 10% to 90%, no condensation

DC12V/AC24V/PoE

6 W

CE, FCC, RoHS Compliant

125 x 82 x 52 mm (L x W x H) (w/o lens)

360 g (0.80 lbs)

77

Appendix B: Internet Security Settings

If ActiveX control installation is blocked, please either set Internet security level to default or change ActiveX controls and plug-ins settings.

Internet Security Level: Default

Step 1: Start the Internet Explorer (IE).

Step 2: Select <Tools> from the main menu of the browser. Then Click <Internet Options>.

Step 3: Click the <Security> tab, and select <Internet>.

78

Step 4: Down the page, press “Default Level” (see the figure above) and click “OK” to confirm the setting. Close the browser window, and open a new one later when accessing the IP Camera.

ActiveX Controls and Plug-ins Settings

Step 1~3: Refer to the previous section above.

Step 4: Down the page, press “Custom Level” (see the figure below) to change ActiveX controls and plug-ins settings.

79

The Security Settings screen is displayed as below:

Step 5: Under “ActiveX controls and plug-ins”, set ALL items (as listed below) to <Enable> or <Prompt>.

ActiveX controls and plug-ins settings:

1. Automatic prompting for ActiveX controls

2. Binary and scrip behaviors

3. Download signed ActiveX controls

4. Download using ActiveX controls

5. Initialize and script ActiveX not marked as safe

6. Run ActiveX controls and plug-ins

7. Script ActiveX controls marked safe for scripting

Step 6: Click <OK> to accept the settings and close the <Security> screen.

Step 7: Click <OK> to close the Internet Options screen.

Step 8: Close the browser window, and restart a new one later for accessing the IP

Camera.

80

Appendix C: DC Viewer Download Procedure

The procedure of DC Viewer software download is specified as follows.

Step 1: In the DC Viewer installation page, click “Next” for starting installing.

Step 2: Setup starts. Please wait for a while until the loading bar runs out.

81

Step 3: Click “Finish” to close the DC Viewer installation page.

Then, the IP Camera’s Home page will display as follows:

82

NOTE: Please note that the function buttons will vary depending on the camera model.

Appendix D: Install UPnP Components

Please follow the instructions below to install UPnP components.

Step 1: Go to “Start”, click on “Control Panel”, and then double click “Add or Remove

Programs”.

Step 2: Click on “Add/Remove Windows Components” in the Add or Remove Programs page.

83

Step 3: Select “Networking Services” from the Components list in the Windows

Components Wizard window, and then click “Details”.

Step 4: Select “UPnP User Interface” in the Networking Services’ subcomponents list and then click “OK”.

84

Step 5: Click “Next” in the Windows Components Wizard page.

Step 6: Click “Finish” to complete installation.

85