Bosch | D9412GV2 | User's Manual | Bosch D9412GV2 User's Manual

D9412GV2/D7412GV2
Operation and Installation Guide
EN
Control Panels
D9412GV2/D7412GV2 | Operation and Installation Guide | Trademarks
Trademarks
®
CoBox is a registered trademark of Lantronix .
Windows® is a registered trademark of Microsoft
Corporation in the United States or in other countries.
®
Molex is a registered trademark of Molex
Incorporated.
Certifications and Approvals
The D9412GV2/D7412GV2 Literature Pack includes
the D9412GV2/D7412GV2 Approved Applications
Compliance Guide (P/N: F01U003639). Refer to this
guide for additional guidelines on installing the control
panels in Underwriters Laboratories Inc. (UL) and firespecific applications.
Federal Communications
Commission (FCC) Rules
Part 15
This equipment was tested and found to comply with
the limits for a Class A digital device, pursuant to Part
15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful
interference when the equipment is operated in a
commercial environment.
This equipment generates, uses, and can radiate radio
frequency energy; and if not installed and used
according to the instructions, can cause harmful
interference to radio communications.
Listings and Approvals
Operation of this equipment in a residential area is
likely to cause harmful interference, in which case the
user is required to correct the interference at his or her
own expense.
Fire
Part 68
UL
This equipment complies with Part 68 of FCC rules. A
label contains, among other information, the FCC
registration number and ringer equivalence number
(REN). If requested, this information must be provided
to the telephone company.
Underwriters Laboratories Inc. (UL) lists the
D9412GV2/D7412GV2 Control Panels as Signal
System Control Units for: Central Station, Local,
Auxiliary, Remote Station, Proprietary, and Household
Fire Warning.
Burglary
UL
UL lists the D9412GV2/D7412GV2 Control Panels
for: Central Station, Local, Police Connect, Bank Safe
and Vault, Mercantile Safe and Vault, and Grade A
Household Systems.
Department of Defense (DOD)
The D9412GV2/D7412GV2 was granted approval for
Department of Defense (DoD) installations in Sensitive
Compartmented Information Facilities (SCIF).
2
The D9412GV2 and D7412GV2 Control Panels are
registered for connection to the public telephone
network using an RJ38X or RJ31X jack.
The REN is used to determine the number of devices
that can be connected to the telephone line. Excessive
RENs on the telephone line may result in the devices
not ringing in response to an incoming call. In most,
but not all areas, the sum of the RENs should not
exceed five. To be certain of the number of devices
that may be connected to the line, as determined by
the RENs, contact the telephone company to determine
the maximum REN for the calling area.
If you experience trouble with the D9412GV2 or
D7412GV2 Control Panel, please contact Bosch
Security Systems Customer Service for repair and
warranty information. If the trouble is causing harm to
the telephone network, the telephone company may
request that the equipment be removed from the
network until the problem is resolved. User repairs
must not be made, and doing so will void the user’s
warranty.
Bosch Security Systems, Inc. | 5/05 | F01U003641B
D9412GV2/D7412GV2 | Operation and Installation Guide | Federal Communications Commission (FCC) Rules
.
If the D9412GV2 or D7412GV2 Control Panel causes
harm to the telephone network, the telephone
company attempts to notify you in advance. If advance
notice is not practical, the telephone company notifies
you as soon as possible. Also, you will be advised of
your right to file a complaint with the FCC if you
believe it is necessary.
The telephone company may make changes in its
facilities, equipment, operations, or procedures that
could affect the operation of the equipment. If this
happens, the telephone company provides advance
notice in order for the necessary modifications to be
made in order to maintain uninterrupted service.
This equipment cannot be used on public coin service
provided by the telephone company. Connection to
Party Line service is subject to state tariffs. (Contact
your state public utilities commission for information.)
FCC Registration Number: AJ9MUL-46532-AL-E
Service Center in USA: National Repair Center
130 Perinton Parkway
Fairport, NY 14450
(800) 289-0096
Ringer Equivalence: 0.4B
Bosch Security Systems, Inc. | 5/05 | F01U003641B
3
D9412GV2/D7412GV2 | Operation and Installation Guide | Contents
Contents
1.0
2.0
2.1
2.2
3.0
3.1
3.1.1
3.1.2
3.2
3.3
3.3.1
3.3.2
3.3.3
3.3.4
3.3.5
3.3.6
3.3.7
3.3.8
3.3.9
3.3.10
3.3.11
3.3.12
3.3.13
3.3.14
3.3.15
3.3.16
3.3.17
4.0
4.1
4.2
4.3
4.4
4.5
4.5.1
4.5.2
4.5.3
4.5.4
4.5.5
4.6
4.6.1
4.6.2
4.6.3
4.6.4
4
Introduction....................................................... 7
Lightning Strikes .............................................. 8
Effects................................................................... 8
Precautions during Installation.......................... 8
Overview ........................................................... 9
Configuration and Parts ..................................... 9
Parts List ............................................................10
Parts Available by Separate Order .................10
Accessories ........................................................11
Features in the D9412GV2 and
D7412GV2 ........................................................12
SDI Molex Connector .....................................12
Tip and Ring Posts ...........................................12
Super Capacitor ................................................12
Telephone Line Sniff........................................12
Points..................................................................12
Areas and Accounts..........................................12
Digital Communicator .....................................12
Keypads .............................................................13
Keyswitch ..........................................................13
Access Control ..................................................13
Event Memory ..................................................13
Event Log ..........................................................13
Ground Fault Detection ...................................13
Ground Fault Detection Added Feature ........13
NetCom Functions ...........................................14
Programming ....................................................14
Other Features ..................................................14
Installation .......................................................15
Installation Preparation....................................15
Enclosure Options ............................................15
Mounting Enclosure .........................................15
Installing the Control Panel.............................16
Connecting Earth Ground...............................16
Terminal 10.......................................................16
Ground Fault Detect Enable ...........................16
Enabling Ground Fault Detection ..................17
D9412GV2 and D7412GV2 Ground Fault
Specifications.....................................................17
Locking the Reset Pin ......................................17
Completing the Installation .............................18
Charging the Battery ........................................18
Installing and Wiring Detection Devices.......18
Installing Modules and Relays ........................18
Connecting the On-board Points
and Keypads......................................................18
4.6.5
4.7
4.8
4.9
5.0
5.1
5.1.1
5.1.2
5.2
5.2.1
5.2.2
5.2.3
5.2.4
5.2.5
5.2.6
6.0
6.1
6.2
6.3
6.4
6.4.1
6.4.2
6.4.3
6.4.4
7.0
7.1
7.2
7.3
7.4
7.5
7.6
7.7
7.8
7.9
7.10
7.11
7.11.1
7.11.2
7.11.3
7.11.4
8.0
8.1
8.2
8.3
8.4
Poweringing Up................................................ 18
Programming the Control Panel .................... 19
Installing the Point Chart Label ..................... 19
Testing the System ........................................... 19
Power Supply.................................................. 20
Primary Power Terminals 1 and 2 ................. 20
Primary (AC) Power Circuit ........................... 20
Installing the Transformer............................... 20
Secondary Power Terminals ........................... 20
Secondary (DC) Power .................................... 20
Installing the Battery........................................ 21
Replacing the Battery ...................................... 22
Battery Supervision .......................................... 23
Battery Charging Circuit ................................. 23
Battery Discharge and Recharge Schedule ... 23
Power Outputs................................................ 25
Circuit Protection ............................................. 25
Total Available Power ..................................... 25
Continuous Power Output
Terminals 3, 8, 24, and 32............................... 25
Programmable Power Output
Terminals 6, 7, and 8 ....................................... 25
Programming .................................................... 25
Terminals 6 and 7 ............................................ 26
Fire System Power Formula............................ 26
Terminal 8......................................................... 26
Telephone Connections ............................... 27
Registration ....................................................... 27
Notification ....................................................... 27
Location............................................................. 27
Telephone Cord Connection .......................... 27
Phone LED (Red)............................................. 28
Operation Monitor LED (Green) ................... 28
Dialing Format.................................................. 28
Telephone Line Monitor ................................. 28
Called Party Disconnect .................................. 28
Communication Failure................................... 28
D928 Dual Phone Line Switcher.................... 29
Description........................................................ 29
Operation .......................................................... 29
Installing the D928........................................... 30
D928 Status LEDs ............................................ 30
On-Board Points............................................. 31
Terminals 11 to 22 Description ...................... 31
Point Sensor Loops .......................................... 31
Point Parameters............................................... 31
Point Response Time ....................................... 32
Bosch Security Systems, Inc. | 5/05 | F01U003641B
D9412GV2/D7412GV2 | Operation and Installation Guide |
.
8.5
9.0
9.1
9.1.1
9.1.2
9.1.3
9.1.4
9.1.5
9.2
9.3
9.3.1
9.3.2
9.3.3
9.3.4
9.3.5
9.3.6
9.3.7
9.3.8
9.4
9.4.1
9.4.2
9.4.3
9.4.4
9.4.5
9.4.6
9.4.7
9.5
10.0
10.1
10.1.1
10.1.2
10.1.3
10.1.4
10.2
10.2.1
10.2.2
10.2.3
11.0
11.1
11.2
11.2.1
Wiring Information for Installations
Using the Ademco AB-12 Bell/Housing........32
Off-Board Points .............................................34
Point (Zonex) Bus: D9412GV2 Terminals
and D7412GV2 Terminals ..............................34
POPIT Modules................................................34
POPEX Modules ..............................................34
Missing Conditions...........................................34
Extra Point Events............................................34
D7212GV2 Responses to
Missing Point Conditons..................................35
D8125, D8127 and D9127 POPIT Modules .35
Installing the D8125 POPEX Module ...........38
Mounting ...........................................................38
Wiring the D8125 to the Control Panel.........38
Wiring POPITs to the
Data Expansion Loop ......................................38
Wiring Data Expansion Loops to
POPEX Modules ..............................................39
POPIT Sensor Loops .......................................39
POPIT Module Point Assignments ................39
Program Record Sheet.....................................39
POPIT Labels ...................................................40
D8128D OctoPOPIT Module.........................40
Description ........................................................40
Listings ...............................................................40
Installation .........................................................41
Setting the OctoPOPIT Switches....................41
Mounting OctoPOPITs....................................42
Wiring OctoPOPITs.........................................42
OctoPOPIT Sensor Loops...............................46
Testing Off-Board Points .................................47
Off-Board Relays ............................................48
D8129 OctoRelay.............................................48
Configuring the D8129 OctoRelay ................49
Relay Outputs ...................................................49
Installation .........................................................49
Wiring Connections .........................................50
D811 Arm Status Relay Module.....................50
Relay Output.....................................................50
Installation .........................................................51
Wiring Connections .........................................51
Arming Devices..............................................53
Description ........................................................53
Keypad Terminals 29 to 32 .............................53
Assigning an Address for the Keypad............53
Bosch Security Systems, Inc. | 5/05 | F01U003641B
11.2.2
11.3
Installation......................................................... 53
D268/D269 Independent Zone Control,
D279A Independent Zone Control................ 55
11.4
Keyswitch .......................................................... 55
11.4.1 Description........................................................ 55
11.4.2 Programming .................................................... 55
11.4.3 Installation......................................................... 55
12.0
SDI Devices ..................................................... 57
12.1
Description........................................................ 57
12.2
Installation......................................................... 57
12.3
D9131A Parallel Printer
Interface Module .............................................. 57
12.3.1 Switch Settings .................................................. 57
12.3.2 Supervision........................................................ 57
12.4
D9210B Wiegand Control
Interface Module .............................................. 57
12.4.1 Access ................................................................ 58
12.4.2 Switch Settings .................................................. 58
12.5
SDI Address 80................................................. 58
12.5.1 Serial Interface Modules (SIMs) ..................... 58
12.5.2 Address Settings ............................................... 58
12.5.3 Supervision........................................................ 59
12.6
SDI Address 88................................................. 59
12.6.1 D9133DC Direct Connect Programming
Module .............................................................. 59
12.6.2 Network Interface Modules ............................ 59
12.6.3 Address Settings ............................................... 60
12.6.4 Supervision........................................................ 60
13.0
Programmer and Accessory
Connections..................................................... 61
13.1
Programmer Connector................................... 61
13.2
Programmer Access Reports........................... 61
13.3
Accessory Connector ....................................... 61
14.0
Faceplates ........................................................ 62
14.1
D9412GV2 Faceplate ...................................... 62
14.2
D7412GV2 Faceplate ...................................... 63
Appendix A: System Wiring Diagrams,
Issue A .............................................................. 64
A.1
D9412GV2 Control Panel............................... 64
A.2
D7412GV2 Control Panel............................... 67
Appendix B: Point Address Charts .......................... 70
B.1
Zonex 1, Points 9 to 127 (D9412GV2);
Zonex 1, Points 9 to 75 (D7412GV2) ............ 70
B.2
Zonex 2, Points 129 to 247
(D9412GV2 Only) ........................................... 71
Specifications................................................................. 72
5
D9412GV2/D7412GV2 | Operation and Installation Guide | 1.0 Introduction
Figure 35:
Figures
Figure 1:
Figure 2:
Figure 3:
Figure 4:
Figure 5:
Figure 6:
Figure 7:
Figure 8:
Figure 9:
Figure 10:
Figure 11:
Figure 12:
Figure 13:
Figure 14:
Figure 15:
Figure 16:
Figure 17:
Figure 18:
Figure 19:
Figure 20:
Figure 21:
Figure 22:
Figure 23:
Figure 24:
Figure 25:
Figure 26:
Figure 27:
Figure 28:
Figure 29:
Figure 30:
Figure 31:
Figure 32:
Figure 33:
Figure 34:
6
System Configuration ................................. 9
Enclosure Mounting..................................15
Ground Fault Detection............................16
Reset Pin.....................................................17
Non-Power-Limited Wiring .....................22
Charging and Battery LEDs.....................23
RJ31X Wiring ............................................27
Phone Connector, Phone LED, and
Operation Monitor LED Locations.........27
D928 Dual Phone Line Switcher.............29
On-board Point Sensor Loop Wiring......31
Wiring for Installation Using the
Ademco AB-12 Bell/Housing ..................33
Connecting the D8125 POPEX to the
D9412GV2 Control Panel........................36
Connecting the D8125 POPEX to the
D7412GV2 Panel ......................................37
Program Record Sheet..............................40
D8128D OctoPOPIT Layout ...................41
Connecting D8128D OctoPOPITs
to the D9412GV2......................................44
Connecting D8128D OctoPOPITs
to the D7412GV2......................................45
Wiring Multiple D8128Ds Using
Molex® Connectors ...................................46
D8128D OctoPOPIT Sensor Loops........47
D8129 Connections to the
D9412GV2.................................................48
D8129 Connections to the
D7412GV2.................................................49
D811 Module Wiring to the
D9412GV2.................................................51
D811 Module Wiring to the
D7412GV2.................................................52
Power at Keypads......................................54
Keyswitch Wiring ......................................55
D9133 Jumper Setting for Address 80 ....58
DX4020i DIP Switch Settings ..................59
DX4020 DIP Switch Settings ...................60
D9133TTL-E Jumper Setting for
Address 88..................................................60
Reset Pin.....................................................61
Programmer and Accessory
Connections ...............................................61
D9412GV2 Faceplate ...............................62
D7412GV2.................................................63
D9412GV2, Power Supply Side ..............64
Figure 36:
Figure 37:
Figure 38:
Figure 39:
D9412GV2, Input Points and
Peripheral Devices .................................... 65
D9412GV2, SDI Devices......................... 66
D7412GV2, Power Supply Side.............. 67
D7412GV2, Input Points and
Peripheral Devices .................................... 68
D7412GV2, SDI Devices......................... 69
Tables
Table 1:
Table 2:
Table 3:
Table 4:
Table 5:
Table 6:
Table 7:
Table 8:
Table 9:
Table 10:
Table 11:
Table 12:
Table 13:
Table 14:
Table 15:
Table 16:
Table 17:
Table 18:
Table 19:
Table 20:
Table 21:
Table 22:
Table 23:
Table 24:
Table 25:
Table 26:
Table 27:
Related Documentation.............................. 7
9000GV2 Series Control Panel
Differences ................................................... 9
Compatible Accessories ........................... 11
Compatible Keypads ................................ 13
Ground Fault Detection Status ................ 17
Ground Fault Impedance Specifications 17
Battery Discharge and Recharge
Schedule ..................................................... 23
Charging Status and Low Battery LEDs 24
Phone Cord Lengths................................. 30
Point Parameters ....................................... 31
POPEX Modules....................................... 34
Extra Point Events .................................... 34
Off-Board Point Errors ............................. 35
Data Expansion Loop Wire
Specifications ............................................. 38
D8128D OctoPOPIT Switch Settings
for D9412GV2 and D7412GV2.............. 42
Switch 5 Settings for Line Termination.. 42
Terminal Strip Connections..................... 43
D8129 OctoRelay Switch Settings .......... 49
Number of D8128Ds Used with
D8129s........................................................ 50
Keypad Address Settings.......................... 53
Keypad Connections ................................ 53
SDI Device Connections.......................... 57
Printer Address Switch Settings............... 57
Address Switch Settings for Access
Control Module......................................... 58
Zonex 1 Point Address Chart .................. 70
Zonex 2 Point Address Chart .................. 71
Specifications ............................................. 72
Bosch Security Systems, Inc. | 5/05 | F01U003641B
D9412GV2/D7412GV2 | Operation and Installation Guide | Tables
.
1.0 Introduction
This manual addresses the operation and installation of the D9412GV2 and D7412GV2 Control Panels.
Throughout this guide, the words “control panel” refer to both control panels (D9412GV2 and D7412GV2).
Table 2 on page 9 provides an overview of the differences between the D9412GV2 and D7412GV2 control panels.
Table 1:
Related Documentation
Name of Documentation∗
Part Number
D1255 Installation Instructions
D1256/D1257 Installation Instructions
D1260 Installation Guide
D1260 Owner’s Manual
74-06819-000
74-06925-000
48101
50410
D5200 Operation Manual
D720 Installation Instructions
74-06176-000
74-06918-000
D7412GV2 Release Notes
D8125MUX Operation & Installation Guide
D9210B Operation and Installation Guide
D9412GV2 Release Notes
D9412V2G/D7412V2G Approved Applications Compliance Guide
43856
36796
32206
F01U003637
F01U003639
D9412GV2/D7412GV2 Installation and Troubleshooting Quick Reference Guide
D9412GV2/D7412GV2 New Features
D9412GV2/D7412GV2 Operation and Installation Guide (this document)
F01U003638
43746
F01U003641
D9412G/D7412G Program Entry Guide
D9412GV2/D7412V2G Program Record Sheet
RPS Operations Manual
Security System Owner's Manual
Security System Owner's Manual Supplement
UL Certificated Bank Safe and Vault Applications Technogram
9000/G/GV2 Series Technical Service Note: UL Smoke Detector Compatibility
F01U003636
F01U003635
38849
71-06633-000
33267
73-07302-000
33284
D8128D Installation Guide
D268/D269 Operation and Installation Instructions
41323
74-004758-000
D279A Operation and Installation Instructions
46458
∗
To obtain any of these documents, please contact Bosch Security Systems Technical Support and request the documentation by its
corresponding part number.
Bosch Security Systems, Inc. | 5/05 | F01U003641B
7
D9412GV2/D7412GV2 | Operation and Installation Guide | 2.0 Lightning Strikes
2.0 Lightning Strikes
The control panels are designed to significantly reduce
electromagnetic interference and malfunction generally
caused by lightning.
2.1
Effects
Any electronic system can be struck directly by
lightning or be adversely affected by a lightning strike
near the system. When lightning strikes, several things
happen:
• An electromagnetic wave spreads from the point of
the strike inducing high voltages in nearby
conductors.
• The voltage changes substantially on electrical
grounds near the lightning strike.
• High voltages are induced upon anything directly
struck by lightning.
Symptoms of installations that lightning might strike or
affect are Missing Trouble, Missing Alarm, or Point
Bus Trouble events. Occasionally, Reboot and
Watchdog events might be sent because the control
panel tried to reset itself.
Electronic systems, including control panels, cannot be
completely immune to direct or indirect lightning
strikes; however, some proven installation practices
might greatly reduce the risk of undesirable affects.
2.2
Precautions during Installation
To minimize the risk of undesirable effects from
lightning strikes on high risk installations that use a
point-bus technology:
• Do not run wiring outside the building.
• If you must install the unit in a metal building,
keep the wiring at least 0.61 m (2 ft) away from
external metal surfaces.
• Earth ground the unit correctly. Do not use an
electrical ground or telephone ground.
• Avoid running wires near telephone, data, or
power lines inside a building. Historical evidence
shows that locating control panel wiring at least
0.61 m (2 ft) away from telephone, data, or power
lines is successful at minimizing lightning damage.
When your data lines must cross the path of AC or
other wiring, cross the lines perpendicularly.
8
Bosch Security Systems, Inc. | 5/05 | F01U003641B
D9412GV2/D7412GV2 | Operation and Installation Guide | 3.0 Overview
.
3.0 Overview
3.1
Configuration and Parts
Figure 1:
System Configuration
D8129 OctoRelay provides alarm
and auxiliary relay output.
(Other functions available.)
D9210B Modules can be
used for access control.
Each D8128D OctoPOPIT combines
eight POPIT points in one module.
DX4020 allows communciation
over a Local or Wide Area Network
(LAN/WAN).
Control
Panel
D8125, D8125INV, or
D8125MUX Interface
used for point expansion.
D928 Module allows the control
panel to monitor two phone lines.
On-Board Points
1 to 8
Use keypads or keyswitches to arm the control
panel by area. Each control panel can have up to eight
areas. Each area can have its own account number or
areas can be grouped together with a common account
number. Points of protection are assigned to areas.
D8132 Modules (two 12 VDC, 7Ah batteries)
provide additional power for keypads and
other powered devices.
D9131A Module connects
to a parallel printer to print
the event log.
Table 2:
GV2 Series Control Panel Differences
Features
D9412GV2
D7412GV2
D7212GV2
Access Control
Yes - 8 doors
Yes - 2 doors
No
Arm/Disarm Passcodes
249
99
99
Cards/Tokens
996
396
N/A
16
4
4
3
1
1
Number of Points
246
75
40
Number of Relays
128
64
24
Number of Areas
8
8
4
Passcode-Protected
Custom Functions
Number of Printers
Bosch Security Systems, Inc. | 5/05 | F01U003641B
9
D9412GV2/D7412GV2 | Operation and Installation Guide | 3.0 Overview
3.1.1
Parts List
The D9412GV2 andD7412GV2 Control Panels are
shipped assembled from the factory with the following
parts:
Literature Pack
• D9412GV2/D7412GV2/D7212GV2 Installation and
Troubleshooting Quick Reference Guide
(P/N: F01U003638)
• D9412GV2/D7412GV2 Program Record Sheet
(P/N: F01U003635)
• 9000/G/GV2 Series Technical Service Note: UL Smoke
Detector Compatibility (P/N: 33284)
• 7000/9000 Series Point Chart Label
(P/N: 79-06660-000)
Assembly
• PC board
• Faceplate shield
• Mounting skirt
• One #6 x 1/4-in. screw
10
3.1.2
Parts Available by Separate Order
Order the following components separately to
complete a basic eight-point installation.
• D1255, D1256, D1257, D1260, or D720 Command
Center (or keypad)
• D1640 Transformer
• D126 or D1218 Battery
• D161 or D162 Phone Cord (order two cords if
using the D928 Dual Phone Switcher)
• D8103, D8108A, or D8109 Enclosure
Configured packages are also available. Please consult
the Bosch Security Systems product catalog.
The following literature is available in a separate
literature package for dealers.
• D9412GV2/D7412GV2 Operation and Installation
Guide (P/N: F01U003641)
• D9412GV2/D7412GV2 Approved Applications
Compliance Guide (P/N: F01U003639)
• D9412GV2/D7412GV2 Program Entry Guide
(P/N: F01U003636)
• D9412GV2/D7412GV2 Program Record Sheet
(P/N: F01U003635)
Bosch Security Systems, Inc. | 5/05 | F01U003641B
D9412GV2/D7412GV2 | Operation and Installation Guide | 3.0 Overview
.
3.2
Accessories
Refer to the Bosch Security Systems product catalog for additional information.
Table 3:
Compatible Accessories
Model
Title
Model
Title
D122/D122L
D125B
D127
D129
D1260
D1640
D5200
D5500
Alpha V Command Center
16.5 VAC 40 VA Transformer
Programmer
Remote Programming Software (RPS)
D8004
D8121A, D8122
D8125
D8125MUX
D8125INV*
D8128D
D8129
Transformer Enclosure
Derived Channel STU
POPEX Module
Multiplex Bus Interface
Wireless Interface Module
OctoPOPIT Module
OctoRelay Module
D442
D448/D449
Dual Battery Harness
Powered Loop Interface Module
Reversing Relay
Dual Class A Initiation Circuit
Module
Relay Module
Plug-In Relay
Phone Cord [2.4 m (8 ft)]
Phone Cord [0.6 m (2 ft)]
Reverse Polarity Module
Bell Circuit Supervision Module
Independent Zone Control
(On-Board and OctoPOPIT Points)
Bells [4 cm (10 in.)]
Mini-horns
D8130
D8132
Release Module
Battery Charger Module
D720
D720R
Command Center (Area LED)
LED Command Center (red)
D9002-5
D9127U/T
Accessory Module Mounting Skirt
POPIT Module
D720W
D928
LED Command Center (white)
Dual Phone Line Switcher
D9131A
D9210B
Parallel Printer Interface Module
Access Control Interface Module
D1218
ZX776Z
D1255R
12 V, 17.2 Ah Rechargeable
Battery
Command Center (General
Purpose)
Text Command Center (red)
ZX865
PIR Motion Sensor [15 m (50 ft)] with
POPIT
PIR Motion Sensor [24 m (80 ft)] with
POPIT
PIR/Microwave Motion Sensor
[+1.7°C (+35°F)] with POPIT
D1255W
Text Command Center (white)
ZX938Z
D1256
Fire Command Center
ZX970
D1257
Fire Annunciator
D130
D136
D161
D162
D185
D192C/D192G
D279A
D1255
ZX794Z
PIR Motion Sensor [18 m (60 ft)] with
POPIT
PIR/Microwave Motion Sensor
[+1.7°C (+35°F)] with POPIT
* The D8125INV was not investigated by UL. Do not use D8125INV in UL Listed installations.
Bosch Security Systems, Inc. | 5/05 | F01U003641B
11
D9412GV2/D7412GV2 | Operation and Installation Guide | 3.0 Overview
3.3
3.3.1
Features in the D9412GV2 and
D7412GV2
SDI Molex Connector
Use the SDI Molex Connector to connect easily an
SDI device with the SDI bus, without needing to
disconnect wires connected to the SDI terminals.
Possible applications include:
• Connecting a DX4010i to program the control
panel with Remote Programming Software (RPS) at
the premises
• Connecting a keypad to test the control panel.
For a D1260ATM keypad, set the address
of the DIP switch to 7. The default for
Address 7 has the Area Scope and
Enhanced CMD Ctr parameters set to Yes.
3.3.5
The Bosch Security Systems D9412GV2 Control Panel
provides up to 246 points of protection. The
D7412GV2 Control Panel provides up to 75 points of
protection. Point programming parameters determine
the control panel response to open and shorted
conditions on the sensor loop for the point. Several
options allow individual point programming to customfit the protection to the installation.
Points 1 to 8 are located on the circuit board (on-board
points). They are standard sensor loops. The remaining
off-board points are POPIT points using D8128D
OctoPOPITs, D8125 POPEX Modules and D9127 or
D8127 POPITs. MUX devices can also be used with
D8125MUX or wireless transmitters with the
D8125INV.
3.3.6
Do not connect the D5200 Programmer to
the SDI Molex connector.
3.3.2
Tip and Ring Posts
The tip and ring posts allow connecting a phone or
buttset for the purpose of troubleshooting
communications between the control panel and the
central station. With this connection, the dial tone,
ACK tone handshake, and ACK and NACK signals
can be monitored.
3.3.3
Super Capacitor
The D9412GV2 and D7412GV2 have a capacitor
called Super Cap. This component preserves the
parameters stored in the control panel’s RAM chip
when the lithium battery is replaced. The Super Cap
can retain voltage for up to 30 minutes after the lithium
battery is removed.
Plan to replace the lithium battery after 3 to 5 years of
continual service.
When replacing the lithium battery, ensure
that you disconnect the primary AC power
and secondary battery power from the
control panel before you remove the old
battery. Then install the new battery and
connect the primary AC and secondary
battery power to the control panel.
3.3.4
Telephone Line Sniff
The D9412GV2 and D7412GV2 control panels
monitor the phone line for the programmed
supervision interval before indicating a phone line
trouble. Phone line trouble occurs when the phone line
voltage drops to 6 V or below, without a corresponding
8 mA to 13 mA increase in current.
12
Points
Areas and Accounts
The system supports up to eight separate areas. You
can assign all points to a single area or distribute them
over as many as eight areas.
The control panel is armed and disarmed by area, and
several areas can be armed and disarmed with one
menu function. A passcode can also be assigned an
authority level that allows a user to arm an area from a
remote keypad in another area. Assigning each area its
own account number creates eight separate accounts in
one control panel. Assigning the same account number
to different areas groups them together in a single
account.
Area options include exit tone and delay, separate fire
and burglary outputs, and multiple opening and closing
windows. Area type can be used to create area
interdependencies for arming purposes.
3.3.7
Digital Communicator
The control panel uses a built-in digital communicator
to send reports to the receiver. The control panel sends
reports in either the Modem IIIa2 or BFSK format. The
MPU and line cards for the D6500 or D6600 receiver
must have software revision 8.00 (or greater) installed
to accept Modem IIIa2 reports from the control panel.
Refer to the D6500 or D6600 literature to determine
the MPU software version.
The control panel connects to an RJ31X or RJ38X jack
for telephone line seizure. Connecting to the RJ31X
complies with FCC regulations for using the public
telephone network. The control panel can be
programmed to direct reports to four separate
telephone numbers. Adding the D928 Dual Phone Line
Switcher Module allows connecting and supervising a
second telephone line.
Bosch Security Systems, Inc. | 5/05 | F01U003641B
D9412GV2/D7412GV2 | Operation and Installation Guide | 3.0 Overview
.
The system can route groups of Event Reports to four
different destinations. Each report group can be
programmed to send reports to one or more
destinations. Primary and backup reporting paths can
be programmed for each destination and each report
group. A custom option allows specification of
individual Event Reports to be sent.
3.3.8
Keypads
Up to 32 unsupervised keypads can be connected to
the system. The available power, number of supervised
keypads, and number of areas covered affect the total
number of keypads that can be connected.
The system can supervise up to eight keypads. The
control panel sends a Serial Device Trouble Report,
SDI FAILURE in the Modem IIIa2 format or
TROUBLE ZN D in the BFSK format, if it loses
communication with a supervised keypad.
More than eight keypads can be added, but supervision
of only eight is possible. Table 4 on page 13 shows the
compatible keypads with the D9412GV2 and
D7412GV2 Control Panels. Refer to Keypad in the
D9412GV2/D7412GV2 Program Entry Guide
(P/N: F01U003639) for complete details on
programming keypad options.
Table 4:
Compatible Keypads
Model
Display
Application
D1255
16-character
alphanumeric
16-character
alphanumeric
16-character
alphanumeric
4-line by 20-character
8 LED
Fire/Burglary/Access
D1256
D1257
D1260
D720
3.3.9
Fire
Fire
Fire/Burglary
Fire/Burglary
Keyswitch
Maintained or momentary closure devices such as
keyswitches allow any of the four available areas to be
armed or disarmed. Point programming determines the
loop responses and which area a keyswitch controls.
3.3.10 Access Control
The D9412GV2 can control eight access doors (each
requiring the optional D9210B Wiegand Control
Interface Module) with up to 996 uniquely identified
cards or tokens. The D7412GV2 can control two access
doors with up to 396 uniquely identified cards or
tokens. Any of the following can grant access:
• Wiegand-style access control device (card reader)
connected to the D9210B Access Control Interface
Module
Bosch Security Systems, Inc. | 5/05 | F01U003641B
•
Request to enter (RTE) or request to exit (REX)
input
• Keypad
The access control features of the D9412GV2 and
D7412GV2 can deny access during armed periods. The
control panel can also grant access only to certain
authorized users depending on whether the area is
master armed, perimeter armed, or disarmed.
Programming for automatic disarming when designated
authorized users are granted access is also possible.
3.3.11 Event Memory
The system uses event memory to store events for each
area. A D1255 Keypad or D1260 Keypad assigned to
an area allows viewing of the events for the area. The
control panel clears the events for an area from event
memory and starts storing new events when the area is
master armed.
3.3.12 Event Log
The system stores 500 to 1000 events and event
modifiers from all areas in its event log. Event
modifiers add information about an event to the log.
Some events are always followed by a modifier. For
example, the system adds at least two items to the log
each time an area is armed or disarmed, the open (or
close) event and an event modifier showing the
previous arming state.
All events and their modifiers can be stored even if the
control panel does not send a report for them. The log
can be viewed at a keypad, printed locally using the
D9131A Parallel Printer Interface Module and a
parallel printer, or uploaded using Remote
Programming Software (RPS).
For a list of the log events and event modifiers, refer to
the appendix in the user’s guide for the keypad.
3.3.13 Ground Fault Detection
The Earth Ground Terminal on the control panels is
electrically isolated from all other terminals to allow
the D9412GV2 and the D7412GV2 to detect ground
fault conditions. A Ground Fault Detect Enable switch
(S4) is located just under Terminal 10, Earth Ground,
on the control panel. Refer to Section 4.5.2 Ground Fault
Detect Enable on page 16 for information on operating
this function.
3.3.14 Ground Fault Detection Added Feature
When Ground Fault Detect is enabled (S4 closed),
Points 1 to 8 can be used for non-powered fireinitiating devices such as heat detectors, four-wire
smoke detectors, and pull stations. A D125B Powered
Loop Interface or a D129 Dual Class A Interface
Module is not required when connecting the nonpowered fire-initiating devices to Points 1 to 8.
13
D9412GV2/D7412GV2 | Operation and Installation Guide | 3.0 Overview
3.3.15 NetCom Functions
3.3.17 Other Features
The D6600 NetCom System supports data network
communications. NetCom allows the D6600 receiver to
connect to various network topologies, specifically
Ethernet and token-ring. NetCom also allows this
receiver to process messages to and from most
networks using TCP/IP protocols. Connecting to a data
network is possible using the COM4 or COM1
connection from the D6600 receiver to the D6680
Network Adapter. Alarm control panels can send
reports through telephone lines or Ethernet and tokenring data networks to the D6600 receiver and then to
the central station automation software or the network
printer through a local area network (LAN) or wide
area network (WAN). The network can monitor the
status of alarm control panels.
D9412GV2 and D7412GV2 Control Panels have many
programmable features. Some of the features are listed
below. Complete details on all features are in the
D9412GV2/D7412GV2 Program Entry Guide
(P/N: F01U003636).
• Supervision of AC (primary power), battery
(secondary power), Zonex and SDI buses, central
processing unit (CPU), up to three printers, and
two telephone lines
• Automatic System Test Reports
• Remote access for programming, diagnostics, and
log uploads using the remote programming
software (RPS)
• Fire alarm verification
• Programmable alarm output
• Programmable relay output using the D8129
OctoRelay Module
• Opening and closing windows
• Skeds (scheduled events)
3.3.16 Programming
Use the Bosch Security Systems D5200 Programmer or
the Remote Programming Software (RPS) to program
the D9412GV2 and D7412GV2 Control Panels. Refer
to the D9412GV2/D7412GV2 Program Entry Guide
(P/N: F01U003636) for programming options.
14
Bosch Security Systems, Inc. | 5/05 | F01U003641B
D9412GV2/D7412GV2 | Operation and Installation Guide | 4.0 Installation
.
4.2
4.0 Installation
4.1
Mount the control panel assembly in any of the Bosch
Security Systems enclosures listed:
• D8103 Universal Enclosure (tan)
• D8109 Fire Enclosure (red)
• D8108A Attack Resistant Enclosure (tan)
Refer to the D9412GV2/D7412GV2 Approved
Applications Compliance Guide (P/N: F01U003639)to
determine if the application requires a specific
enclosure.
Installation Preparation
This section contains a general installation procedure
and refers to other sections of the document for
detailed instructions.
Review this document and the D9412GV2/D7412GV2
Program Entry Guide (P/N: F01U003636) before
beginning the installation to determine the hardware
and wiring requirements for the features used.
Have the following documentation available when
reading through this guide:
• D9412GV2/D7412GV2 Program Record Sheet
(P/N: F01U003635)
• Security System Owner’s Manual
(P/N: 71-06633-000) and Security System Owner’s
Manual Supplement (P/N: 33267)
• Command center (keypad) installation manual
(D1255, D1256, D1257, D1260, or D720)
Before installation, become familiar with the operation
of the D5200 Programmer or the RPS.
Figure 2:
Enclosure Options
4.3
1.
2.
Mounting Enclosure
Run the necessary wiring throughout the premises.
Mount the enclosure in the desired location. Use
all five enclosure mounting holes. Refer to Figure 2.
Pull the wires into the enclosure.
3.
Electro-Magnetic Interference (EMI) can cause
problems on long wire runs. Refer to EMI on Long Wire
Runs in the D9412GV2/D7412GV2/D7212GV2
Installation and Troubleshooting Quick Reference Guide
(P/N: F01U003638).
Enclosure Mounting
3
1
2
2
4
7
8
3
5
9
6
12345-
Point chart label
Mounting skirt hooks (2)
Module mounting holes (12)
Tamper switch mounting holes (5)
Skirt mounting hole (1)
Bosch Security Systems, Inc. | 5/05 | F01U003641B
6789-
Enclosure mounting holes (5)
Mounting skirt hook holes (2)
Back of D9412GV2/D7412GV2 Control Panel
Lock down tab
15
D9412GV2/D7412GV2 | Operation and Installation Guide | 4.0 Installation
4.4
1.
2.
3.
4.5
Installing the Control Panel
Place the control panel over the inside back of the
enclosure, aligning the large rectangular openings
of the mounting skirt with the mounting hooks of
the enclosure. Slide the control panel down so that
it hangs on the hooks. Refer to Figure 2, Item 2 on
page 15.
Remove the tape from the #6 x 1/4-in. screw in
the mounting tab on the control panel. The screw
passes through the mounting tab and into the skirt
mounting hole in the enclosure. Tighten the screw
to secure the control panel in the enclosure.
Connect earth ground to the control panel before
making any other connections. Refer to Section 4.5
Connecting Earth Ground.
Connecting Earth Ground
•
If a ground fault condition occurs, the keypads
display SERVC GND FAULT and the control panel
transmits a GROUND FAULT TROUBLE, AREA 1
(Modem IIIa2 format only).
When the control panel recognizes that the ground
fault condition is corrected, and remains corrected
for between 5 to 45 consecutive seconds, a Restoral
Report is sent.
The D9412GV2 and D7412GV2 Control
Panels log and print a Ground Fault event
as a Trouble Point 256 if communicating in
Modem IIIa2 format. If communicating in
BFSK format, the control panels generate
an Alarm Zone 5 event.
Figure 3:
4.5.1
Terminal 10
To help prevent damage from electrostatic charges or
other transient electrical surges, connect the system to
earth ground at Terminal 10 before making other
connections. Recommended earth ground references
are a grounding rod or a cold water pipe.
Ground Fault Detection
1
Warning:
2
Do not use telephone or electrical ground
for the earth ground connection. Use
1.8 mm (14 AWG) to 1.5 mm (16 AWG)
wire when making the connection.
Do not connect other control panel
terminals to earth ground.
3
GROUND FAULT DETECT
Enabled
Disabled
RED
4.5.2
Ground Fault Detect Enable
• A ground fault is a circuit impedance to earth
ground. The control panel has a ground fault
detection circuit that, when enabled, detects
ground faults on Terminals 1 to 9 and 11 to 32.
The control panel also detects and annunciates
ground faults on any device connected to it.
• To enable ground fault detection, the Ground Fault
Detect Enable jumper (S4) (Figure 3) must be
locked (closed) and a non-zero value must be
entered in the Area 5 Silent Alarm Relay. When
jumper S4 is in the unlocked (open) position, the
control panel does not detect ground fault
conditions.
16
PHONE
LED
S4
ON when
communicating
OFF when idle
PHONE LINE SEIZED
TIP
TELCO CORD
MODEL D161
RING
1 - With S4 closed, control panel detects ground
faults.
2 - With S4 open, control panel does not detect
ground faults.
3 - S4, Ground fault detect enable.
Bosch Security Systems, Inc. | 5/05 | F01U003641B
D9412GV2/D7412GV2 | Operation and Installation Guide | 4.0 Installation
.
4.5.3
Enabling Ground Fault Detection
To configure the D9412GV2 and D7412GV2 Control
Panels to enable ground fault detection:
1.
Set the silent relay in Area 5 to any value from 1
to 128. Do not use a zero (0) value.
The default value for the Area 5 silent relay
is 0 (zero). The 0 value disables the ground
fault detection function.
Close Switch S4 (Figure 3 on page 16). Refer to
Table 5 for information about the conditions for
enabling and disabling the Ground Fault
Detection Circuit.
2.
Table 5:
Disabled
4.5.4
Switch S4
Value of Area 5
Silent Relay Alarm
Closed
Closed
Open
1 to 128
0
0 to 128
D9412GV2 and D7412GV2 Ground Fault
Specifications
Table 6 provides the impedance specifications for
detecting ground faults when any terminal or field
wiring is shorted to ground.
Table 6:
Impedance
Ground Fault Impedance
Specifications
Locking the pin in the disable position applies power to
the control panel and charges the battery while the
detection devices and keypads are installed.
Figure 4:
Reset Pin
1
Reset Pin
Disable All Except Battery
Charging And Programming
PERIPHERAL DEVICE CONNECTIONS
POWER +
32
YELLOW
DATA BUS A
31
GREEN
DATA BUS B
30
BLACK
COMMON
29
RED
2
Control Panel Detects Ground Fault
≤ 300 Ω
Yes
300 Ω to
200 kΩ
No
≥ 200 kΩ
Detection depends upon the terminal
4.5.5
If the reset pin is placed in the disable position when
all areas are armed, there must be an entry in the
Answer Armed program item. Refer to RPS Parameters
in the D9412GV2/D7412GV2 Program Entry Guide
(P/N: F01U003636).
Ground Fault Detection Status
Ground Fault
Detection Circuit
Enabled
Releasing the reset pin from the closed position resets
the control panel. The control panel resets all its timers,
counters, indexes, and buffers. Any points that restore
after a reset do not generate Restoral Reports.
1 - Reset pin locked (closed).
2 - Reset pin normal (open).
Locking the Reset Pin
Locking the reset pin disables the control panel
(Figure 4). When the control panel is disabled, the
system ignores the keypads and points. CALL FOR
SERVICE appears in keypad displays when the pin is
locked down.
On-board relays (Terminals 6 and 7) and off-board
relays deactivate when the control panel is reset.
Terminal 8 has power when the relay is deactivated.
Activation interrupts power at that terminal. The onboard relay (Terminal 8) remains deactivated when the
reset pin is locked in the disable position.
Bosch Security Systems, Inc. | 5/05 | F01U003641B
17
D9412GV2/D7412GV2 | Operation and Installation Guide | 4.0 Installation
4.6
Completing the Installation
If not already complete, make the earth ground
connection to Terminal 10 and lock the reset pin in the
closed position.
4.6.1
4.6.3
Installing Modules and Relays
1. Power down the unit by unplugging the
transformer and disconnecting the battery.
Always power down the unit when installing
modules or relays, or when making wiring
connections to the control panel.
Charging the Battery
Connect the battery, then the transformer to allow the
control panel to charge the battery while you complete
the installation. Refer to Section 5.0 Power Supply on
page 20 for instructions.
2.
On-board Buzzer Sounds at Power Up and Reset:
The system performs a series of self-diagnostic tests of
hardware, software, and programming at power up and
at reset. The buzzer on the control panel sounds during
the tests. The self-diagnostics tests complete in
approximately 1 to 3 seconds.
If the control panel fails any test, the buzzer continues
sounding and a System Trouble message appears at the
keypads. Refer to Problems Found during Self Diagnostics
in the D9412GV2/D7412GV2/D7212GV2 Installation and
Troubleshooting Quick Reference Guide (P/N: F01U003638)
for a description of each system trouble message.
Instructions for the D8125 POPEX Module,
D8128D OctoPOPIT Module, D8129 OctoRelay
Module, D811 Arm Status Relay Module, and
D928 Dual Phone Line Switcher appear in this
guide.
3.
Touch Terminal 10 First: If the on-board buzzer
sounds briefly when the control panel is touched, any
static charge you carry discharges to the control panel.
Avoid electrostatic discharge. Always touch
Terminal 10, the earth ground connection,
before beginning work on the control panel.
If the control panel receives an electrostatic discharge,
it might generate Watchdog Reset and Param
Fail events. Refer to Watchdog Reset Reports in the
D9412GV2/7412G/D7212GV2 Installation and
Troubleshooting Quick Reference Guide
P/N: F01U003638) for a description of these events.
4.6.2
Installing and Wiring Detection Devices
Install and wire detection devices and keypads at their
locations throughout the premises. Do not connect the
control panel yet.
Section 8.0 On-Board Points on page 31 contains
instructions for wiring the on-board points to detection
devices. Section 11.0 Arming Devices on page 53 contains
instructions for wiring the keypads.
Instructions for wiring the off-board point POPIT
sensor loops are found in the instructions packaged
with the POPIT modules.
18
Install and wire any modules required for the
installation as described in the module’s
installation instructions.
Refer to Section 9.0 Off-Board Points on page 34 for
D8125 and D8128D instructions. Refer to Section
10.0 Off-Board Relays on page 48 for D8129 and
D811 instructions. Refer to Section 7.11 D928 Dual
Phone Line Switcher on page 29 for D928
instructions.
If using the power outputs at Terminals 7 or 8,
install a D136 relay in the appropriate sockets.
Refer to Section Programmable Power Output
Terminals 6, 7, and 8 on page 25 for instructions.
4.6.4
Connecting the On-board Points and
Keypads
Connect the on-board points and keypad wiring to the
system. Refer to Section 8.0 On-Board Points on page 31
and Section 11.0 Arming Devices on page 53 for
instructions.
4.6.5
Powering Up
Reconnect the battery, then plug in the transformer.
The buzzer sounds for 2 seconds when the control
panel is powered up. Leave the reset pin in the locked
position.
Yellow Charging Status LED Remains Lit: If the
yellow charging status LED remains lit after five
minutes of powering up the control panel, either the
battery is deeply discharged or too many powered
devices were connected to the control panel.
Combined continuous current draw for Terminals 3, 8,
24, and 32, and the accessory connector cannot exceed
1.4 A. Refer to Section 6.0 Power Outputs on page 25 for
help.
Bosch Security Systems, Inc. | 5/05 | F01U003641B
D9412GV2/D7412GV2 | Operation and Installation Guide | 4.0 Installation
.
4.7
Programming the Control Panel
If the control panel is not already programmed, review
the D9412GV2/D7412GV2 Program Entry Guide
(P/N: F01U003636). Ensure that all accessory modules
for desired features are available for installation. Place
the reset pin in the locked position to copy or send
information to and from the control panel.
Use the D5200 Programmer or the RPS to load a
custom program into the control panel.
Move the reset pin to the normal position refer to
(Figure 4 on page 17). The control panel sends Reboot
and Battery Reports to the receiver if programmed for
reporting
4.8
Installing the Point Chart Label
The point chart label is required for fire
systems with verifications points.
A point chart label comes in the literature pack. Install
the point chart label for fire or combined fire-andburglary systems that use verification points.
Use the D9412GV2/D7412GV2 Program Record Sheet
(P/N: F01U003635) to gather the necessary information
for completing the point chart. Fill out the label and
install it on the inside of the enclosure door (refer to
Figure 2 on page 15).
Avoid smearing the entries on the chart.
Use the peel-off backing to press the label
in place.
4.9
Testing the System
After installing and programming the control panel,
test the system completely. Test the control panel and
all devices for proper operation. Test after initially
programming the control panel and after subsequent
programming sessions.
Refer to the D9412GV2/D7412GV2/D7212GV2
Installation and Troubleshooting Quick Reference Guide
(P/N: F01U003638) for complete Service Walk Test
instructions.
Clear after Test: To clear the event memory and
report buffer, momentarily close the reset pin. Events
stored in the control panel’s event log are not cleared.
Bosch Security Systems, Inc. | 5/05 | F01U003641B
19
D9412GV2/D7412GV2 | Operation and Installation Guide | 5.0 Power Supply
5.
5.0 Power Supply
5.1
Primary Power Terminals 1 and 2
5.1.1
Primary (AC) Power Circuit
The primary source is a 16.5 VAC, 40 VA, internallyfused transformer (Bosch Security Systems Model
D1640). The control panel draws 200 mA when idle
and 500 mA when in an alarm state. The total available
auxiliary current is 1.4 A.
Transient suppressors and spark gaps protect the circuit
from power surges. This protection relies on the
ground connection at Terminal 10. Ensure that you
connect Terminal 10 to a proper ground. Refer to
Section 4.5 Connecting Earth Ground on page 16.
AC Power Failure
The system indicates an AC power failure when
Terminals 1 and 2 do not have power. The AC Fail
Time program item sets the number of minutes or
seconds without AC power before the control panel
acknowledges the failure and the number of minutes or
seconds after the power returns before the control
panel acknowledges restored power. Refer to the
D9412GV2/D7412GV2 Program Entry Guide
(P/N: F01U003636) for additional information about
AC Fail Time.
5.1.2
Installing the Transformer
Do not short the terminals of the
transformer: Shorting the terminals opens
the internal fuse, causing permanent failure.
Connect the transformer to Terminals 1 and
2 of the control panel before plugging it into
the power source.
1.
2.
Secure the transformer to the outlet with the screw
provided.
D8004 Transformer Enclosure Required for Fire
Systems: Use the D8004 Transformer Enclosure for
the D1640 Transformer in fire and combined fire and
burglary applications.
Check with the Authority Having Jurisdiction (AHJ)
about mounting transformers on specific circuits.
5.2
Secondary Power Terminals
5.2.1
Secondary (DC) Power
A 12 V, 7 Ah (up to 14 Ah) sealed lead-acid
rechargeable battery (D126) supplies secondary power
for auxiliary and alarm outputs, and powers the system
during interruptions in primary (AC) power.
Warning - Use Lead Acid Batteries Only:
The charging circuit is calibrated for leadacid batteries. Do not use gel-cell or nicad
batteries.
Extra Batteries Increase Back-up Time: To increase
battery back-up time, connect a second 12 V, 7 Ah
battery in parallel to the first battery to form a 12 V, 14
Ah battery. Use a D122 Dual Battery Harness to ensure
proper and safe connection.
Caution: When connecting two D1218
Batteries to the control panel, both must have
the same capacity (use two 17.2 Ah batteries
or two 18 Ah batteries).
D1218 Battery
The D1218 is a 12 V, 17.2 or 18 Ah battery for use in
applications requiring extended battery standby time.
Up to two D1218 batteries can be connected when
used with a D122 Dual Battery Harness.
Use 1.22 mm (18 AWG) wire (minimum) to
connect the transformer to the control panel.
The wire length should be as short as possible. The
maximum length is 15 m (50 ft.). Connect the
battery and plug in the transformer.
Route telephone and sensor loop wiring away from
any AC conductors, including the transformer
wire.
AC wiring can induce noise and low level voltage
into adjacent wiring. Route data wiring away from
AC and telephone wiring.
Always connect the battery first and then
plug in the transformer.
3.
4.
20
Connect the battery. Refer to Section 5.2.2 Installing
the Battery on page 21.
Plug the transformer into an unswitched, 120 VAC,
60 Hz power outlet only.
Bosch Security Systems, Inc. | 5/05 | F01U003641B
D9412GV2/D7412GV2 | Operation and Installation Guide | 5.0 Power Supply
.
5.2.2
Installing the Battery
1. Place the battery upright in the base of the
enclosure.
2. Locate the red and black leads supplied in the
literature pack.
3. Connect the black battery lead to Terminal 4, and
then to the negative (-) side of the battery.
4. Connect the red battery lead to Terminal 5, and
then to the positive (+) side of the battery.
Warning: High current arcs are possible. The
positive (red) battery lead and Terminal 5 can
create high current arcs if shorted to other
terminals or the enclosure. Use caution when
working with the positive lead and Terminal 5.
Always disconnect the positive (red) lead
from the battery before removing it from
Terminal 5.
Caution: The battery terminals and wire are
not power limited. A 6.4 mm (0.250 in.)
space must be maintained between the
battery terminals, battery wiring, and all other
wiring. Battery wiring cannot share the same
conduit, conduit fittings, or conduit knockouts with other wiring. Refer to Figure 5 on
page 22.
Bosch Security Systems, Inc. | 5/05 | F01U003641B
21
D9412GV2/D7412GV2 | Operation and Installation Guide | 5.0 Power Supply
Figure 5:
Non-Power-Limited Wiring
2
1
1
2
+ AUX
4
BATTERY NEGATI
5
3
4
D
3
Maximum Charging
Current 1.4 Amps.
BATTERY POSITIVE ONLY
6
RELAY A
7
RELAY B
8
RELAY C
9
10
PROGRAMMABLE
ALARM OUTPUTS
Terminals
7 & 8
Requires Optional
D136 Relay
In ALT ALARM
& SW AUX
COMMON
EARTH GROUND
GROUND FAULT DETECT
Enabled
Disabled
RED
RED
Point 1 Point 2
ON when
communicating
OFF when idle
PHONE LINE
PHONE
LINE SEIZED
SEIZED
PHONE
PHONE
LED
LED
TIP
TIP
11
RING
RING
12
13
TELCO
TELCO
RED
ON when
PHONE communicating
LED
OFF when idle
PHONE LINE SEIZED
TIP
RING
TELCO
5
6
1 - Conduit, required only if external batteries are
used.
2 - Battery wires
3 - 6.4 mm (0.25 in.) minimum. To ensure proper
spacing, use tie-wraps or similar devices to secure
wires.
5.2.3
Replacing the Battery
Replace batteries every 3 to 5 years under normal use.
Record the date of installation directly on the battery.
Caution: Exceeding the maximum output
ratings or installing the transformer in an
outlet that is routinely switched off causes
heavy discharges. Routine heavy discharges
can lead to premature battery failure.
D8132 Boost Battery Backup: Adding a D8132
Battery Charger Module supports additional batteries
of up to 27 Ah capacity, if required. The D8132 Battery
Charger Module can be used to connect two additional
batteries for a total of four.
22
456-
Option wires
Output or zone wires
Standby battery
The control panel plus any connected D8132 Modules
and auxiliary power supplies must be on the same AC
circuit to discharge evenly if AC power fails. The
number of D8132 Modules is determined by the
number of available outlets on the same circuit. Refer
to the Standby Battery and Current Rating Chart in the
D9412GV2/D7412GV2 Approved Applications Compliance
Guide (P/N: F01U003639) for battery standby time
calculations.
In applications where the supervision of two
batteries is required by the AHJ, use a D113
Battery Supervision Module.
Bosch Security Systems, Inc. | 5/05 | F01U003641B
D9412GV2/D7412GV2 | Operation and Installation Guide | 5.0 Power Supply
.
5.2.4
Battery Supervision
When battery voltage drops to 13.8 VDC, the yellow
Charging Status LED illuminates. When the battery
voltage drops to 12 VDC to 11.8 VDC, the red Low
Battery LED lights, and the keypad or keypads display
SERVC LOW BATT. The control panel (if programmed
for power supervision) sends a BATTERY LOW report
in the Modem IIIa2 communication format. It sends a
TROUBLE ZN 9 report in the BFSK format.
If the battery is missing or shorted, the red Low Battery
LED flashes at the same rate as the green Operation
Monitor LED. If the control panel is programmed for
power supervision, it sends a BATTERY MISSING
report in the Modem IIIa2 communication format, or
TROUBLE ZN 9 report in the BFSK format.
When battery voltage returns to 13.7 VDC, the Low
Battery LED turns off and the keypad or keypads clear
the SERVC LOW BATT message. If the control panel is
programmed for power supervision, it sends a
BATTERY RESTORAL report in the Modem IIIa2
communication format or a RESTORAL ZN 9 report in
the BFSK format. At 13.9 VDC, the yellow Charging
Status LED stops lighting.
Figure 6:
Charging and Battery LEDs
LEDs Off When Normal
YEL
Charging Status
RED
Low Battery
Investigate Low Battery reports immediately: If
primary (AC) power is off and the discharge continues,
the control panel becomes inoperative when the
battery voltage drops below 10.2 VDC.
5.2.5
Battery Charging Circuit
Float Charge
The float voltage for the battery charging circuit is
13.9 VDC at a maximum current of 1.4 A, less any
devices connected to the control panel. If the float
voltage drops below 13.8 VDC due to overload or
battery discharge, the yellow Charging Status LED
lights.
Loss of AC Load Shed Relay protects battery:
During an AC power loss, the battery supplies all
power to the security system. If the battery voltage falls
below 10.0 V during an AC power loss, a load shed
relay isolates the battery from the control panel and
disables the control panel. Load shed protects the
battery from being damaged by deep discharge. When
AC power restores, the load shed relay reconnects the
charging circuit on the control panel to the battery and
the battery begins to recharge.
Overcharge Load Shed With AC Present: If more
than 1.4 A of auxiliary current draw from the control
panel occurs, the battery supplies the current and
begins to discharge. If this situation is not corrected, the
battery continues to discharge and at 11.8 VDC to
12.0 VDC, the keypads display Serv Low Batt.
When the battery voltage drops below 10.0 VDC, the
control panel shuts down. Remove all loads to the
control panel and disconnect AC power. Add a new
battery and reconnect AC power.
Reset the control panel by momentarily placing the
reset pin in the disable position. Refer to Figure 4 on
page 17. The red Low Battery LED continues flashing
until the control panel resets.
A shorted battery condition is created either by a
shorted cell inside the battery or by a short on
Terminals 4 and 5. A shorted battery might cause the
control panel to operate in an unsafe way. This
condition generates WATCHDOG RESET reports.
5.2.6
Battery Discharge and Recharge Schedule
Table 7:
Battery Discharge and Recharge
Schedule
Discharge Cycle
AC Off:
13.9 VDC:
13.8 VDC:
12.0 VDC:
< 10.0 VDC:
Recharge Cycle
AC On:
13.7 VDC:
13.9 VDC:
Bosch Security Systems, Inc. | 5/05 | F01U003641B
AC Fail Report when AC fails, if
control panel is programmed to report
AC failure at occurrence.
Charging float level.
Charging status LED on.
Low Battery and AC Fail Reports if
programmed. Low battery LED on.
Battery load shed (processing
functions continue if AC is present).
Load shed relay reset; battery
charging begins; Battery Trouble and
AC Restoral Reports sent.
Battery Restoral Reports sent. Low
battery LED off.
Changing status LED off; battery float
charged.
23
D9412GV2/D7412GV2 | Operation and Installation Guide | 5.0 Power Supply
Table 8:
Charging Status and Low Battery LEDs
LED
Type
Color
Charging Status LED
Yellow
Low Battery LED
24
State
Yellow
Off
Yellow
On
Yellow
Flash once per
minute
Red
Action
Shows the changing status of the battery. Refer to Figure 6 on
page 23 for location.
Battery is fully charged.
If the battery is missing, shorted, or reversed, the Charging Status
LED is off, but the red Low Battery LED is flashing.
Battery float charge is below 13.8 VDC. If AC is present, the battery
is charging.
Indicates the combined current draw from all outputs exceeds 1.4 A.
This is normal under alarm conditions for non-fire systems with sirens
or bells drawing more than 1.4 A. If the LED lights regularly for
extended periods or does not go out, check the current draw for
devices connected to the power outputs. Refer to Section 6.0
Power Outputs on page 25 for instructions.
System is checking the battery.
Shows the condition of the battery. Refer to Figure 6 on page 23 for
location.
Battery is fully charged.
Red
Off
Red
On
Battery voltage dropped to between 12.0 VDC and 11.8 VDC.
LED turns off when voltage reaches 13.7 VDC.
Red
Flash
(same as green
LED)
Green LED is Operation Monitor LED.
Battery is missing or shorted.
Bosch Security Systems, Inc. | 5/05 | F01U003641B
D9412GV2/D7412GV2 | Operation and Installation Guide | 6.0 Power Outputs
.
6.0 Power Outputs
6.1
Circuit Protection
Three Positive Temperature Coefficients (PTCs) protect
the control panel from short circuits on the continuous
and programmable power outputs. If the control panel
is programmed for power supervision and a short
circuit occurs on one of the power outputs, the control
panel sends a BATTERY LOW or BATTERY MISSING
for Bosch Security Systems Modem IIIa2
Communication Format, or TROUBLE ZN 9 for BFSK.
One PTC protects :
• Terminal 3: Auxiliary Power
• Terminal 24: Zonex Power.
A short-circuit on one terminal disrupts
power to the other terminal.
Another PTC protects:
• Terminal 6: Alarm Power Output
• Terminal 7: Alternate Alarm Power Output
• Terminal 8: Switched Auxiliary Power.
A short-circuit on one of the terminals
disrupts power to the other two terminals.
The third PTC protects Terminal 32: Power +.
6.2
Total Available Power
The system produces up to 1.4 A of combined power at
10.2 VDC to 13.9 VDC for all powered devices. The
outputs listed below share the available power. These
outputs are shown as red circles on the faceplate.
Terminal 3 - Auxiliary Power: Use this terminal to
power devices requiring continuous power.
Terminal 6 (Relay A) - Alarm Power Output:
Normally open, power on alarm.
Terminal 7 (Relay B) - Alternate Alarm Power
Output: Normally open, power on alarm.
Terminal 8 (Relay C) - Switched Auxiliary Power:
Normally closed, switches power off when the Sensor
Reset command is executed.
Terminal 24 - Zonex Power: Use this terminal to
power Zonex modules such as the D8125, D8128D,
and D8129 Modules.
Terminal 32 - Power +: Use this terminal to power
serial device interface (SDI) devices such as keypads,
the D9131A Parallel Printer Interface Module, and the
D9210B Wiegand Control Interface Module.
Bosch Security Systems, Inc. | 5/05 | F01U003641B
Accessory Connector: The D928 Dual Phone Line
Switcher connects to the accessory connector.
6.3
Continuous Power Output Terminals
3, 8, 24, and 32
The continuous current draw for powered devices
connected to Terminals 3, 8, 24, and 32, and the
accessory connector must not exceed 1.4 A. Devices
powered from these outputs must operate over a range
of 10.2 VDC to 13.9 VDC.
Power Restricted for Fire and Combined Fire and
Burglary Systems: Use the Fire System Power
Formula to calculate the current available for fire and
combined fire and burglary systems (refer to Section 6.4
Programmable Power Output Terminals 6, 7, and 8 on page
25).
6.4
Programmable Power Output
Terminals 6, 7, and 8
6.4.1
Programming
The power outputs at Terminals 6, 7, and 8 are
programmed as Relays A, B, and C. All relays are
programmed in the Relays section.
Relays are assigned a relay type, (Fire Bell, for
example) when they are assigned to an area. Relays
can be assigned to one or more areas.
The Bosch Security Systems defaults set Relay A
(Terminal 6) as a Steady Alarm Bell output, Relay B
(Terminal 7) as a Pulsed Fire Bell output, and Relay C
(Terminal 8) as a Verification or Reset output for
smoke detectors. The D9412GV2/D7412GV2 Program
Entry Guide (P/N: F01U003636) contains complete
instructions for programming relays. Refer to Sections
6.4.2 Terminals 6 and 7, 6.4.3 Fire System Power Formula,
and 6.4.4 Terminal 8 on page 26 for descriptions of the
functions of each terminal.
Refer to the Bell Parameters section of the program to
set the Fire Bell, Alarm Bell output responses for relays.
Four annunciation patterns are available: Steady,
Pulsed, California Standard, and Temporal Code 3.
Voltage Output at Terminals 6, 7, and 8
If Terminals 6, 7, and 8 do not provide the expected
output, check:
• Programming for Relays A, B, and C in the relays
section of the program.
• Bell Parameters section of the program to confirm
that the Alarm and Fire Bell responses are
programmed for the expected duration and
pattern.
• Point Assignments section to confirm that each
point is programmed for the expected local
response.
25
D9412GV2/D7412GV2 | Operation and Installation Guide | 6.0 Power Outputs
6.4.2
Terminals 6 and 7
6.4.4
When activated, Terminals 6 (Relay A) and 7 (Relay
B), provide positive (+) 10.2 VDC to 13.9 VDC power
output. Use the power at Terminals 6 and 7 to power
bells, siren drivers, piezoelectric fire sounders,
electronic horns, or other devices.
Programming determines the format of the output and
the conditions that activate it. One PTC protects
Terminals 6, 7, and 8 against shorts.
Available Power
The system combines the 1.4 A of primary power
produced by the power supply with the secondary
power source (the battery) to produce a total of 2.0 A
of alarm power at 10.2 VDC to 13.9 VDC. Terminals 6
and 7 share the available alarm power.
Power Restricted for Fire and Combined Fire and
Burglary Systems: Fire systems are prohibited from
using the battery for determining alarm power. Use the
fire system power formula that follows to calculate the
current available for fire and combined fire and
burglary systems.
6.4.3
Fire System Power Formula
To calculate the current available at Terminals 6 and 7
for fire and combined fire and burglary systems:
1. Add together the current draws for all devices
connected to Terminals 3, 8, 24, and 32, and the
accessory connector. This is the total current
required for the normal standby condition (NSC).
2. The current available for NSC is 1.4 A. Subtract
the NSC current required calculated in Step 1 from
the NSC current available, 1.4 A. The difference is
the alarm current available for Terminals 6 and 7.
In formula format:
1.4 A − NSC current required
(Step 1)
=
Terminal 8
Terminal 8 provides continuous positive (+) 10.2 VDC
to 13.9 VDC power. Relay C interrupts the power at
Terminal 8 when activated. Use Terminal 8 to power
smoke detectors or other devices that are reset by
interrupting power. One self-resetting circuit breaker
protects Terminals 6, 7, and 8 against shorts.
Verification/Reset Relay
The default program sets Relay C (Terminal 8) as a
verification and reset relay. Refer to Relay Parameters
and Point Assignments in the D9412GV2/D7412GV2
Program Entry Guide (P/N: F01U003636) for instructions
on programming verification and reset relays and
points.
Performing a sensor reset at a keypad produces a fivesecond relay activation of verification/reset relays. The
control panel ignores verification/reset points during
the five seconds.
Alarm current
available
Refer to the D9412GV2/D7412GV2 Approved
Applications Compliance Guide (P/N: F01U003639) for
module or accessory current requirements.
26
Bosch Security Systems, Inc. | 5/05 | F01U003641B
D9412GV2/D7412GV2 | Operation and Installation Guide | 7.0 Telephone Connections
.
7.0
Telephone Connections
7.1
Registration
Figure 7:
RJ31X Wiring
RING (red)
R1
R
The Bosch Security Systems D9412GV2/D7412GV2
Control Panels are registered with the Federal
Communication Commission (FCC) under Part 68, for
connection to the public telephone system using an
RJ31X or RJ38X jack installed by the local telephone
company.
2
RJ31X
TIP (green)
T
T1
1 2
4
5
7 8
1
4
5
8
1
4
5
8
1
4
3
An RJ31X jack can be modified by placing a
jumper wire between Terminals 2 and 7 to
become an RJ38X jack.
5
7.2
Notification
Do not connect registered equipment to party lines or
coin-operated telephones. Notify the local telephone
company and provide the following information before
connecting the control panel to the telephone network:
• The particular line to which the control panel will
be connected
• Make (Bosch Security Systems), model
(D9412GV2 or D7412GV2), and serial number of
the control panel
• FCC registration number: AJ9MUL-46532-AL-E
• Ringer equivalence for the control panel: 0.4B
7.3
Location
To prevent jamming of signals, wire the RJ31X or
RJ38X jack before the in-house telephone system to
support line seizure (Figure 7). Install the jack on the
street side of the telephone switch, wired ahead of any
PBX equipment. Line seizure temporarily interrupts
normal telephone usage while the control panel sends
data. After installation, confirm that the control panel
seizes the line, acquires dial tone, reports correctly to
the receiver, and releases the telephone line to the inhouse telephone system.
Figure 8:
6
123456-
7.4
RJ31X Jack
(TIP)
(RING)
Telco connector block
Outside telco
Premises telephone
Telephone Cord Connection
Connect one end of a D161 (2.1 m [7 ft.]) or a D162
[61 cm (2 ft.)] Telephone Cord to the telco cord
connector located on the bottom left corner of the
control panel. Refer to Figure 8. Connect the other end
to the RJ31X or RJ38X jack.
To supervise the phone cord, use an RJ38X
jack.
Phone Connector, Phone LED, and Operation Monitor LED Locations
D5200/D5360
PROG CONN
Point 8
S3 Option
RED
1
PHONE
LED
Closed = 1KΩ EOL
Normal Operation
ON when
communicating
OFF when idle
PHONE LINE SEIZED
TIP
TELCO CORD
MODEL D161
RING
11
12
13
14
15
16
17
18
19
20
21
22
Open =AB-12 UL
Bell Box 220 KΩ
GRN
PHONE LINE
SEIZED
2
TIP
RING
TELCO
1 - Phone LED (red)
2 - Telephone cord connector
Bosch Security Systems, Inc. | 5/05 | F01U003641B
3
3 - Operation Monitor LED (green)
27
D9412GV2/D7412GV2 | Operation and Installation Guide | 7.0 Telephone Connections
The red Phone LED illuminates when the control panel
seizes the telephone line and remains illuminated until
the control panel returns the telephone line. Refer to
Figure 8 on page 27 for the location of the red LED.
Bad Line Might Test OK: The telephone line monitor
uses voltage levels to test the status of the telephone
line. In some instances, a given telephone line might be
out of service without affecting the voltage on the line.
The telephone line monitor cannot recognize this
trouble condition.
7.6
7.9
7.5
Phone LED (Red)
Operation Monitor LED (Green)
The green Operation Monitor LED indicates the
operation of the central processing unit (CPU). When
the CPU is operating normally, the LED flashes 0.5 sec
on, 0.5 sec off.
This green LED also serves as a ring indicator. The
LED is located on the lower right side (Figure 8 on page
27). When there is ring voltage on the telephone line
(the telephone is ringing), the green LED flashes at a
faster rate for the duration of each ring. Ring voltage
must reach a minimum of 45 VAC before the system
detects it.
7.7
Dialing Format
The system can be programmed to use DTMF or pulse
dialing. Refer to Phone Parameters in the
D9412GV2/D7412GV2 Program Entry Guide
(P/N: F01U003636).
7.8
Telephone Line Monitor
Called Party Disconnect
Telephone companies provide “called party
disconnect” to allow the called party to terminate a call.
The called party must go on hook (hang up) for a fixed
interval before a dial tone is available for a new call.
This interval varies with telephone company
equipment. Control panel firmware allows for “called
party disconnect” by adding a 35-second, “on hook”
interval to the dial tone detect function. If the control
panel does not detect a dial tone in 7 seconds, it puts
the telephone line on hook for 35 seconds to activate
“called party disconnect,” goes off hook, and begins a
seven-second dial tone detect. If no dial tone is
detected, the control panel dials the number anyway.
Each time the number is dialed, the control panel
records this as an attempt.
7.10
Communication Failure
After two attempts to reach the receiver, the control
panel generates and sends a COMM FAIL PH # event.
The event that triggered the telephone call to the
central station follows the COMM FAIL PH # event.
The control panel has a built-in telephone line monitor
that tests the telephone line for voltage and current. If
the D928 Dual Phone Line Switcher is used to connect
two telephone lines to the control panel, the control
panel monitors both lines. The normal voltage on a
telephone line is approximately 48 VDC (24 VDC for
some telephone systems). The telephone line monitor
senses trouble if voltage on the line falls to
5.0 to 7.0 VDC without a corresponding 13 mA of
current.
After ten attempts to reach the receiver, the control
panel enters communication failure. The control panel
clears any reports in its telephone buffer and COMM
FAIL RTE # event is generated, which appears in the
display at keypads. A trouble sounder can be
programmed to annunciate at the keypads.
If the monitor senses trouble, it starts a programmable
telephone line trouble timer, which continues to run as
long as the monitor senses trouble. It resets to zero
when the control panel senses a normal line. If the
timer reaches the delay time in the Phone Supervision
program item, it begins a telephone line trouble
response. Programming determines what the response
is. Refer to Phone Parameters in the
D9412GV2/D7412GV2 Program Entry Guide
(P/N: F01U003636).
If the D928 Dual Phone Line Switcher is used, the
control panel makes a total of ten attempts before
entering communication failure.
Any time the control panel uses the telephone line to
make a call or is on-line with the remote programming
software (RPS), it stops monitoring the telephone line
during this process. When the telephone line on the
control panel is no longer in use, it begins to monitor
the telephone line again.
28
One hour after the COMM FAIL RTE # is generated,
the control panel attempts to send this event. If the
COMM FAIL RTE # event is the only event in the
queue and cannot reach the central station, the keypads
do not turn on the trouble sounder again.
Enhanced Communication
The D9412GV2 and D7412GV2 Control Panels can
send events over the SDI Bus to a DX4020 or
D9133TTL-E Network Interface Module (NIM). For
more information on the enhanced communications
capabilities, refer to GV2AUX in the
D9412GV2/D7412GV2 Program Entry Guide
(P/N: F01U003636).
Bosch Security Systems, Inc. | 5/05 | F01U003641B
D9412GV2/D7412GV2 | Operation and Installation Guide | 7.0 Telephone Connections
.
7.11
D928 Dual Phone Line Switcher
Figure 9:
D928 Dual Phone Line Switcher
7.11.1 Description
The optional D928 Dual Phone Line Switcher allows
the control panel to send reports over two separate
telephone lines. The control panel monitors both lines.
If a line generates a signal and the control panel senses
that a line is bad, the control panel attempts to use the
other telephone line to send the message. If trouble is
detected, the control panel keeps the faulty telephone
line in memory.
1
+
+
2
3
4
Set the Ring Count above 2 on Answering
Machines: The control panel’s RPS line monitor
feature might not operate correctly if an answering
machine with a ring count of less than two rings is
connected to a telephone line used by the D928
Module.
5
6
7
7.11.2 Operation
8
Refer to Phone in the D9412GV2/D7412GV2 Program
Entry Guide (P/N: F01U003636) for telephone
supervision and reporting options. To use the D928, set
the Two Phone Lines prompt to Yes.
When the D928 is installed, the control panel alternates
between Phone Line 1 and Phone Line 2 to send its
first report. For example, on day one, the control panel
first attempts to communicate on Phone Line 1. On
day two, the control panel switches and attempts to
communicate on Phone Line 2.
Any time the control panel resets or is
powered down or up, the next reported event
always attempts to call out on Phone Line 1
first.
If Phone Line 2 is not in service on “Day 2”,
the control panel switches to the primary
phone line to send the report.
With the D928 Dual Phone Line Switcher installed, the
control panel uses two telephone lines (primary and
secondary) to dial up to four telephone numbers.
When using a primary and a backup device within a
Route Group #, the control panel makes two attempts
on the primary telephone line using the Primary
Device # as programmed. If these two attempts fail,
the control panel switches to the secondary telephone
line using the Backup Device # as programmed. This
pattern continues for a total of ten attempts. After ten
unsuccessful attempts, the control panel generates a
Comm Fail event for the given Route Group #.
Bosch Security Systems, Inc. | 5/05 | F01U003641B
9
10
11
1 - Connect to ACCESSORY CONNECTOR with
ribbon cable.
2 - Green to Terminal 1
3 - Black to Terminal 9
4 - AC Power LED (green)
5 - Phone jack to primary phone line
6 - Primary Fail LED (yellow)
7 - Phone jack to secondary phone line
8 - Secondary Fail LED (yellow)
9 - Phone jack to telco connector
10 - Communications Fail LED (yellow)
11 - Buzzer
29
D9412GV2/D7412GV2 | Operation and Installation Guide | 7.0 Telephone Connections
7.11.3 Installing the D928
7.11.4 D928 Status LEDs
Mounting
Four LEDs mounted on the front edge of the D928
Module show the status of AC power for the control
panel, the status of the two telephone lines, and
communication failure (Figure 11 on page 33). When
programmed and operating normally, only the green
AC power status LED is lit.
Mount the D928 on the lower right side of the
enclosure using the screws provided with the switcher.
Wiring
The D928 has two flying leads. The green lead
monitors AC power. The black lead is the ground
reference for the AC Power LED.
1. Connect the green lead from the D928 to
Terminal 1.
2. Connect the black lead from the D928 to
Terminal 9.
Telephone Connections
1. Plug one end of the ribbon cable provided into J4
on the control panel. Plug the other end of the
ribbon cable into the ACCESSORY connector on
the control panel.
2. Plug one end of the D162 phone cord provided
into the telco jack. Plug the other end of the phone
cord into the telco jack on the control panel. Refer
to Error! Reference source not found. for phone
cord lengths.
Table 9:
3.
4.
Phone Cord Lengths
Phone Cord
Length
D161
2.4 m (8 ft)
D162
61 cm (2 ft)
AC Power LED
The green AC Power Status LED lights when AC
power is applied to Terminals 1 and 2 on the control
panel.
Phone Line Fail LEDs
Two yellow Phone Line Status LEDs (one for the
primary telephone line, one for the secondary
telephone line) light if the voltage on the telephone line
falls to between 5.0 and 7.0 VDC, without the
corresponding current of 13 mA. The control panel
monitors the faulty telephone line for the programmed
interval before indicating a trouble condition. Refer to
Section 7.8 Telephone Line Monitor on page 28 for a
description of phone line monitor operation.
Communication Failure LED
The yellow Communication Failure LED lights when
the system is in communication failure. The LED turns
off when communication restores. Refer to Section 7.10
Communication Failure on page 28.
Plug one end of a D161 or D162 phone cord into
J1 on the control panel. Plug the other end of the
phone cord into the RJ31X or RJ138X for the
primary telephone line.
Plug one end of a D161 or D162 phone cord into
J2 on the control panel. Plug the other end of the
phone cord into the RJ31X or RJ138X for the
secondary telephone line. Refer to Error!
Reference source not found. for phone cord
lengths.
If you installed a D928 before November 19,
2001 on a D9412GV2 or D7412GV2,
disconnect AC power from the control panel
(battery must remain connected) and observe
the green LED.
If this LED glows dimly, contact Customer
Service at (800)289-0096 for a replacement
module at no charge.
30
Bosch Security Systems, Inc. | 5/05 | F01U003641B
D9412GV2/D7412GV2 | Operation and Installation Guide | 8.0 On-Board Points
.
8.0 On-Board Points
8.1
Terminals 11 to 22 Description
The control panel provides eight on-board points. Each
point functions independently and does not interfere
with the operation of the others. The control panel
monitors the sensor loops for normal, shorted, or open
conditions between an input terminal (11, 13, 14, 16,
17, 19, 20, or 22) and any of the point common
terminals (12, 15, 18, and 21). Programming for the
point determines how the control panel responds to
those conditions. Refer to the D9412GV2/D7412GV2
Program Entry Guide (P/N: F01U003636) for point
programming options. The control panel also monitors
the sensor loops for ground fault conditions if S4 is
latched (ground fault detect enabled).
8.2
Point Sensor Loops
When wiring the on-board points (Figure 10), install
a 1 kΩ resistor at the far end of the sensor loop to
provide a reference for supervision. Dry-contact
sensing devices can be connected in series (normallyclosed) or in parallel (normally-open) to any of these
loops.
The number of normally-open and normally-closed
detection devices each sensor loop can supervise is
limited only by the resistance on the loop. The total
resistance for the wire length and contacts, minus the
end-of-line (EOL) resistor, must not exceed 100 Ω.
8.3
Point Parameters
The condition of on-board Points 1 to 8 is determined
by measuring the voltage across the point input
terminal and one of the common terminals. The sensor
loops must be connected and the 1 kΩ EOL resistor in
place.
Table 10:
Point Parameters
Loop
Voltage Range
Open
Normal
Greater than 3.7 VDC, but less than 5.0 VDC.
Greater than 2.0 VDC, but less than 3.0 VDC.
Shorted
Greater than 0.0 VDC, but less than 1.3 VDC.
Figure 10: On-board Point Sensor Loop Wiring
1
2
3
4
7
1 kΩ
2
3
5
8
9
10
2
6
123456-
100 Ω maximum
Point input terminal
Common
Normally-closed contacts (NC)
Normally-open contacts (NO)
Combination: Normally-open contacts and
normally-closed contacts (NO/NC)
Bosch Security Systems, Inc. | 5/05 | F01U003641B
7 - P105F (Package of 8 EOL resistors) or
P105BL (Package of 8 UL Listed EOL
resistors) (P/N: 15093130-004)
8 - Brown
9 - Black
10 - Red
31
D9412GV2/D7412GV2 | Operation and Installation Guide | 8.0 On-Board Points
8.4
Point Response Time
The control panel scans both on-board and off-board
point sensor loops every 300 ms. The Debounce
program item in the Point Assignment section of the
software determines point response time by setting the
number of times the control panel scans a point before
generating an alarm.
The debounce count can range from 2 to 15; therefore,
point response time ranges from 600 ms to 4.5 sec. The
Bosch Security Systems default for debounce count is 2.
Increasing debounce might cause missed
alarms. If you increase the debounce count,
detection devices can enter alarm and reset
without exceeding the point response time.
Use a debounce count of 2 for all points except for
Interior Follower points. Program Interior Follower
points as 3. Program door points connected to a
D9210B Access Control Interface Module with a
debounce of 4.
32
8.5
Wiring Information for Installations
Using the Ademco AB-12
Bell/Housing
1.
Disconnect the wire jumper from Terminal 4 to the
inner housing of the Bell Box to prevent a ground
fault condition.
2.
Connect wiring between the control and Bell Box
(Figure 11 on page 33).
To use the AB-12 Bell/Housing, place the S3
switch in the disabled (open) position. The EOL
used in the AB-12 Bell/Housing must be a 220 kΩ,
0.5 W resistor.
3.
Program Point 8 as 24-hour, alarm on, open, and
short. (PT TYPE 0, PT RESPONSE 0).
Bosch Security Systems, Inc. | 5/05 | F01U003641B
D9412GV2/D7412GV2 | Operation and Installation Guide | 8.0 On-Board Points
.
Figure 11: Wiring for Installation Using the Ademco AB-12 Bell/Housing
1
2
CLASS 2 TRANSFORMER
16.5 VAC 40 VA 60 Hz
Model D1640
Internally Fused - Do Not short
Requires Unswitched Outlet
Do Not Share With Other Equipment
3
+ AUX POWER
4
BATTERY NEGATIVE ONLY
5
Maximum Charging
Current 1.4 Amps.
BATTERY POSITIVE ONLY
6
RELAY A
7
RELAY B
8
RELAY C
9
10
D9412GV2
PROGRAMMABLE
ALARM OUTPUTS
Terminals
7 & 8
Requires Optional
Model D136 Relay
In ALT ALARM
& SW AUX
COMMON
VOLTAGE RANGES
Open
3.7 - 5.0 VDC
Normal
2.0 - 3.0 VDC
Short
0.0 - 1.3 VDC
EARTH GROUND
GROUND FAULT DETECT
Enabled
Disabled
RED
PHONE
LED
Point 1 Point 2
Point 3 Point 4
Point 5 Point 6
Point 7 Point 8
ON when
communicating
OFF when idle
PHONE LINE SEIZED
TIP
TELCO CORD
MODEL D161
11
RING
12
13
14
15
16
17
18
19
20
21
22
PHONE LINE
SEIZED
TIP
RING
TELCO
1 2 3 4 5 6
1
5
2
3
4
1 - Bell
2 - Inner bell box lining
3 - Outer bell box
Bosch Security Systems, Inc. | 5/05 | F01U003641B
4 - Bell tampers
5 - 220 kΩ 0.5 W EOL resistor (provided with the
Ademco AB-12 Bell/Housing)
33
D9412GV2/D7412GV2 | Operation and Installation Guide | 9.0 Off-Board Points
9.0 Off-Board Points
9.1
Point (Zonex) Bus: D9412GV2 Terminals and D7412GV2 Terminals
9.1.1
POPIT Modules
The D9412GV2 can use point of protection input transponder (POPIT) modules to provide a maximum of 238
off-board points, bringing the total number of points the D9412GV2 can monitor to 246. The D7412GV2
provides up to 67 off-board points, bringing the total number of points the D7412GV2 monitors to 75. Each offboard point requires a POPIT Module.
9.1.2
POPEX Modules
POPITs connect to supervised two-wire data expansion loops run from POPIT to POPIT throughout the
premises. Data expansion loops connect to a D8125 Point of Protection Expander (POPEX) Module. POPEX
Modules have power and data connections to the point bus on the control panel (Table 11).
Table 11:
POPEX Modules
Model
Power
D9412G
Terminals 23 and 24
D7412G
Terminals 3 and 9
9.1.3
Data
Terminals 25 and 26
or
Terminals 27 and 28
Terminals 22 and 28
Missing Conditions
If a programmed POPIT is disconnected from the expansion loop, a missing condition appears immediately and
the event is logged. The missing condition might also be sent to a central station or printed to an on-site printer, if
programmed to do so. Refer to the D9412GV2/D7412GV2 Program Entry Guide (P/N: F01U003636) for
programming options.
9.1.4
Extra Point Events
Extra Point events are generated when a POPIT connected to the data expansion bus does not have an assigned
Point Index. Table 12 shows when an Extra Point event is or is not generated. Table 13 on page 35 shows
additional error conditions that can occur for the off-board points.
Table 12:
Extra Point Events
A POPIT connected to the data
expansion bus does not have an
assigned Point Index and:
Extra Point event?
Data expansion bus is disconnected
Data expansion bus restores to normal
condition after an open condition
No
Yes
Point input changes status from normal
to open or shorted
During a Service Walk Test, the point
input changes status from normal to
open or shorted
No
∗
34
∗
Yes
Additional Information
Keypad does not annunciate or display a trouble condition.
•
Keypad annunciates and displays a trouble condition
•
Extra Point is logged and might be programmed to
send reports to the central station or to an on-site
printer.
Keypad does not annunciate or display a trouble condition.
•
•
Keypad annunciates and displays a trouble condition
Extra Point is logged and might be programmed to
send reports to the central station or to an on-site
printer.
The Service Walk Test never shows the electrical state of a point as “Extra.”
Bosch Security Systems, Inc. | 5/05 | F01U003641B
D9412GV2/D7412GV2 | Operation and Installation Guide | 9.0 Off-Board Points
.
Table 13:
Off-Board Point Errors
Error Condition
Result
+/- leg of the data expansion bus has a
short-circuit to earth ground, with Ground
Fault Detect enabled
+/- leg of the data expansion bus is
disconnected
Ground Fault event
Data expansion bus has a short-circuit
+/- leg of the data expansion bus has a
short-circuit to the Common terminal on
the D7212G
Terminal 28 has a short-circuit to a
Common terminal
Terminal 27 has a short-circuit to a
Common terminal
Terminals 27 and 28 have a short-circuit
together
9.1.5
All POPITs beyond the
disconnection send Missing
report
•
All POPITs send Missing
report
•
Pt Bus Trouble event
•
•
When the data expansion bus restores, Pt
Bus Restore event occurs. If any POPIT is
connected to the data expansion bus
without an assigned Point Index, an Extra
Point event occurs.
All POPITs send Missing
report
Pt Bus Trouble event
No Pt Bus Trouble event occurs
•
•
•
•
Pt Bus Trouble event
Keypad displays:
SERVC ZONEX 1
Pt Bus Trouble event
Keypad displays:
SERVC ZONEX 1
D9412GV2/D7412GV2 Responses to
Missing Point Conditions
The D9412GV2 and D7412GV2 respond to missing
point conditions based on the point’s programming and
the armed state of the point’s area. For example, if an
interior motion detector point is missing during a
disarmed state, a Missing Trouble event is generated;
however, if the point is missing while the area is Master
Armed, a Missing Alarm event is generated. Non-fire,
24-hour points always generate a Missing Alarm event
whereas Fire points always generate a Missing Fire
Trouble event.
9.2
Additional Information
D8125, D8127 and D9127 POPIT
Modules
D8127 and D9127 POPITs use the D8125 POPEX
Module to report to the control panel. Each D8125
supports up to 119 POPIT points. Connect two D8125
Modules to the D9412GV2 to bring the combined total
number of POPIT and on-board points to 246. Points 9
to 127 connect to the first POPEX Module. Points 129
to 247 connect to the second POPEX Module. The
D9412GV2 reserves Points 128 and 248 for internal
use. The control panel annunciates activity only for
each POPIT, not for each detection device connected
to the sensor loop.
Bosch Security Systems, Inc. | 5/05 | F01U003641B
There are two versions of the D8127 and D9127
Modules. Both module enclosures are made of UL
Listed fire resistant material. D8127T and D9127T
Modules contain tamper switches. D8127U and
D9127U Modules include untampered covers. Unless
the module is mounted in a tampered enclosure, UL
requires D8127T and D9127T Modules for certificated
accounts.
Listings
The D8125 POPEX and the D8127 and D9127 POPIT
Modules are UL Listed for Local or Police Connected
Burglar Alarm, Central Station Burglar Alarm,
Household Burglar Alarm, Central Station Fire, Local
Fire, Remote Station Fire, Household Fire, and
Electrically Actuated Transmitter Applications.
Refer to the D9412GV2/D7412GV2 Approved
Applications Compliance Guide (P/N: F01U003639) to
determine the required equipment and enclosures for
the application.
35
D9412GV2/D7412GV2 | Operation and Installation Guide | 9.0 Off-Board Points
Figure 12: Connecting the D8125 POPEX to the D9412GV2 Control Panel
1
2
Reset Pin
Disable All Except Battery
Charging And Programming
(-)
(-)
(+)
(+)
PERIPHERAL DEVICE CONNECTIONS
POWER +
32
YELLOW
DATA BUS A
31
GREEN
DATA BUS B
30
BLACK
COMMON
29
ZONEX OUT 1
28
ZONEX IN 1
27
ZONEX OUT 2
26
ZONEX IN 2
25
ZONEX POWER +
24
ZONEX COMMON
23
RED
N.F.P.A.
Style 3.5
Signaling
Line
Circuits
1
4
D9127U/T
GND
OUT
IN
AUX
3
(+)
2
4
D9127U/T
D9127U/T
3
3
4
(-)
6
5
2
(-)
(-)
(+)
(+)
D5200/D5360
PROG CONN
Point 8
S3 Option
2
2
2
D9127U/T
3
4
D9127U/T
3
4
D9127U/T
3
4
Closed = 1KΩ EOL
Normal Operation
Open =AB-12 UL
Bell Box 220 KΩ
21
22
GND
OUT
IN
AUX
GRN
(+)
(-)
6
5
7
8
1234-
36
D8125 POPEX Module
Switch block
D9127 Sensor Loop
33 kΩ EOL resistor (P/N: P106F, package of eight)
5678-
Zone expansion loop
Up to 119 POPITs
On-board points
Expansion zones
Bosch Security Systems, Inc. | 5/05 | F01U003641B
D9412GV2/D7412GV2 | Operation and Installation Guide | 9.0 Off-Board Points
.
Figure 13: Connecting the D8125 POPEX to the D7412GV2 Panel
2
RED
Pin
Battery
amming
Low Battery
4
D9127U/T
3
E CONNECTIONS
1
2
CLASS 2 TRANS
16.5 VAC 40 VAC
Model D1640
Internally Fuse
Requires Unsw
Do Not Share
3
+ AUX PO
4
BATTERY N
5
Maximum Charging
Current 1.4 Amps.
BATTERY POSITIVE ONLY
6
RELAY A
7
RELAY B
8
RELAY C
9
10
PR
AL
POWER +
COMMON
EARTH GRO
D9127U/T
4
4
D9127U/T
3
3
32
DATA BUS A
31
DATA BUS B
30
COMMON
29
ZONEX OUT 1
28
ZONEX IN 1
27
NOT USED
26
NOT USED
25
NEX POWER +
24
COMMON
23
Re
2
2
GROUND FAUL
D5200/D5360
PROG CONN
(+)
(-)
5
1
6
7
(-)
(-)
(+)
(+)
GND
OUT
IN
AUX
1234-
D8125 POPEX Module
Switch block
D9127 Sensor Loop
33 kΩ EOL resistor (P/N: P106F, package of eight)
Bosch Security Systems, Inc. | 5/05 | F01U003641B
5 - Zone expansion loop
6 - Up to 67 POPITs
7 - Expansion zones
37
D9412GV2/D7412GV2 | Operation and Installation Guide | 9.0 Off-Board Points
9.3
Installing the D8125 POPEX Module
For information on the Multiplex Bus
Interface, refer to the D8125 Multiplex Bus
Interface Operation and Installation Guide
(P/N: 36796).
Save the POPIT Label Sheets: The D8125 is
packaged with two sets of POPIT label sheets. One set
is marked “Bank 1” for use with the D7412GV2 and
D7212GV2. The other set is marked “Bank 2” for use
with the D9412GV2 and D9112. Use the sheets later to
label the POPITs. Refer to Section 9.3.6 POPIT Module
Point Assignments on page 40.
9.3.1
Wiring the D8125 to the Control Panel
To wire one or two D8125 Modules to the control
panel (Figure 12 on page 36 and Figure 13 on page 37):
Power Down the Control Panel: Disconnect the
positive (red) battery lead at the battery and unplug the
transformer.
For Points 9 to 127 (9 to 75 on D7412GV2):
1. Connect the GND terminal of the D8125 to
Terminal 23 on the D9412GV2 or to Terminal 9
on the D7412GV2.
2.
Connect the OUT terminal of the D8125 POPEX
Module to ZONEX IN 1, Terminal 27.
3.
Connect the IN terminal of the D8125 POPEX
Module to ZONEX OUT 1, Terminal 28.
4.
Connect the AUX terminal of the D8125 to
Terminal 24 on the D9412GV2 or to Terminal 3
on the D7412GV2.
For Points 129 to 247 (D9412GV2 only):
1.
Wiring POPITs to the Data Expansion Loop
Use one two-wire data expansion loop or distribute the
POPITs on up to three loops. Setting DIP switches on
the POPIT Modules assigns them to point numbers.
Refer to Section 9.3.6 POPIT Module Point Assignments on
page 39.
Review Section 4.6.2 Installing and Wiring Detection
Devices on page 18 to determine if shielded wire is
required. Determine the wire gauge for the length of
each data expansion loop using Table 14
Table 14:
Data Expansion Loop Wire
Specifications
Mounting
To install the D8125 in the enclosure with the control
panel:
1. Align the D8125 POPEX Module with any of the
four mounting locations in the enclosure
(Figure 2 on page 15).
2. Using the screws provided with the module, secure
it in the enclosure.
9.3.2
9.3.3
Connect the GND terminal of the D8125 to
Terminal 23.
2.
Connect the OUT terminal of the D8125 POPEX
Module to ZONEX IN 2, Terminal 25.
3.
Connect the IN terminal of the D8125 POPEX
Module to ZONEX OUT 2, Terminal 26.
4.
Connect the AUX terminal of the D8125 to
Terminal 24.
Maximum Length of All Data Expansion Loops
Combined
AWG
Length in Meters (Feet)
22
548 (1800)
20
881 (2890)
18
1402 (4600)
16
2231 (7320)
14
3551 (11,650)
Combine Data Expansion Loops: The maximum
lengths shown in Table 14 are for all data expansion
loops connected to the same POPEX Module
combined.
Wiring POPITs Together: Do not connect POPITs to
each other in series or with a T-tap. Doing so might
cause random missing POPIT conditions.
To connect POPITs to one another in parallel:
1.
Connect the positive (+) data terminal from one
POPIT to the positive (+) data terminal on the next
POPIT.
2.
Connect the negative (-) data terminal from one
POPIT to the negative (-) data terminal on the next
POPIT.
3.
Repeat Steps 1 and 2 to connect all POPITs to the
expansion loop. It is not necessary to wire the
POPITs in any particular order on the loop. The
switch setting on each POPIT assigns it a point
number, regardless of its physical location.
Before installing the POPITs, make sure the
resistance on the data expansion loop is no
more than 40 Ω.
Three-inch Clearance for Tampered POPITs:
Mount tampered POPIT modules at least 7.6 cm (3 in.)
apart to prevent the tamper magnets from interfering
with each other.
Refer to Section 9.3.4 Wiring Data Expansion Loops to
POPEX Modules on page 39 for instructions on
connecting POPITs to the D8125 POPEX Module.
38
Bosch Security Systems, Inc. | 5/05 | F01U003641B
D9412GV2/D7412GV2 | Operation and Installation Guide | 9.0 Off-Board Points
.
9.3.4
Wiring Data Expansion Loops to POPEX
Modules
For the D9412GV2, Points 73 to 127 and
193 to 247 must use the D9127 POPITs.
Points 9 to 72 and 129 to 192 can use
either D8127 or D9127 POPITs.
Each POPEX Module has two positive (+) and two
negative (-) data expansion loop terminals. Up to 119
POPITs can be connected to one D8125 on the
D9412GV2; 67 for the D7412GV2 (Figure 12 on page
36 and Figure 13 on page 37.
For the D7412GV2, Points 9 to 72 can use
either D8127 or D9127 POPITs; however,
D9127 POPITs must be used for Points 73
to 75.
To connect the data expansion loops to the D8125
POPEX Module:
1.
2.
Connect the positive (+) data terminal from the
first POPIT on the data expansion loop to one of
the D8125’s positive (+) terminals.
Connect the negative (-) data terminal from the first
POPIT on the data expansion loop to one of the
D8125’s negative (-) terminals.
9.3.5
POPIT Sensor Loops
The number of normally-open and normally-closed
detection devices each sensor loop can supervise is
limited only by the resistance on the loop. Resistance
on each sensor loop must be less than 100 Ω not
including the EOL resistor.
Certain UL and NFPA applications can limit the
number of detection devices. Consult the appropriate
UL or NFPA standards.
POPITs detect open, shorted, normal, and grounded
circuit conditions on their sensor loops. They send the
condition of their loops to the control panel. A ground
on the sensor loop sends a general system ground-fault
condition report. Refer to Ground Fault in the
D9412GV2/D7412GV2/D7212GV2 Installation and
Troubleshooting Quick Reference Guide
(P/N: F01U003638). Each POPIT is programmed and
sends signals to the control panel separately.
Terminate each POPIT sensor loop with the 33 kΩ
EOL resistor (D106F) included with each POPIT.
Use a twisted-pair wire (six twists per foot) in all
POPEX and POPIT installations for both the data
expansion loop wiring and the POPIT sensor loops.
Run wires away from AC sources to prevent AC
induction. If a noisy environment is suspected, use
shielded cable. Refer to Section 9.3 Installing the D8125
POPEX Module on page 38.
9.3.6
9.3.7
Program Record Sheet
The first column of the table in Figure 14 on page 40
contains the POPIT Switch Settings for the D8127
POPITs. On the D8127 POPITs, the switches are
numbered 1 to 6, from left to right. On the D9127
POPIT, switches are numbered 0 to 6, from left to
right. Set the indicated switches to the ON position. If a
dash (−) appears in the switch position, set the switch to
the OFF position.
The second column contains the Translation of the
point number into the Zonex format. Refer to Point
User Flag in the D9412GV2/D7412GV2 Program Entry
Guide (P/N: F01U003636) for an explanation of this
feature.
The third column contains the Point Number as
shown at keypads.
The fourth column contains the Point Index. Refer to
Point Index Parameters in the D9412GV2/D7412GV2
Program Entry Guide (P/N: F01U003636)for an
explanation of the point index.
The fifth column, Area Assign, shows the area to
which the point is assigned.
The sixth column shows the Debounce Count for the
point. Refer to Debounce Count in the
D9412GV2/D7412GV2 Program Entry Guide
(P/N: F01U003636).
The seventh column shows the BFSK/Relay report
code, which is the point number reported for this point
when the control panel is using the BFSK format.
The eighth column contains the Custom Point Text
displayed at keypads for the point. The text is sent to
the receiver when the control panel uses the Modem
IIIa2 format.
POPIT Module Point Assignments
Six switches on each POPIT assign the module to a
point number. For POPIT switch settings, refer to Point
Assignment in the D9412GV2/D7412GV2 Program Record
Sheet (P/N: F01U003635). The program record sheet
provides information about the Point Assignments
tables. Figure 14 on page 40 is an example of the tables.
Bosch Security Systems, Inc. | 5/05 | F01U003641B
39
D9412GV2/D7412GV2 | Operation and Installation Guide | 9.0 Off-Board Points
Figure 14: Program Record Sheet
EN | 25
D9412GV2/D7412GV2 | Program Record Sheet | RADXPNTS Handler
bold
Default values are shown in ( ) or in bold
Point Assignments (001 through 040)
POPIT Switch
Setting
0 1 2 3 4 5 6
9.3.8
Trans- Point
lation
#
Point
Index
Area
Assign
Custom Point Text
100
001
(3)
__
(1)
___
(2)
_____
(1)
____
P1 FIRE
___________________
200
002
(1)
__
(1)
___
(2)
_____
(2)
____
P2 PANIC
___________________
300
003
(25) _ _
(1)
___
(2)
_____
(3)
____
P3 DELAY
___________________
400
004
(13) _ _
(1)
___
(2)
_____
(4)
____
P4 FOLLOW ___________________
500
005
(7)
__
(1)
___
(2)
_____
(5)
____
P5 INSTANT ___________________
600
006
(7)
__
(1)
___
(2)
_____
(6)
____
P6 INSTANT ___________________
700
007
(7)
__
(1)
___
(2)
_____
(7)
____
P7 INSTANT ___________________
800
008
(7)
__
(1)
___
(2)
_____
(8)
____
P8 INSTANT ___________________
101
009
(1)
___
(2)
_____
(1)
____
P9
__ __
POPIT Labels
9.4
D9412GV2 off-board points are numbered 9 to 127
and 129 to 247. The D7412GV2 uses Points 9 to 75
only. The D9412GV2 reserves Points 128 and 248 for
internal use. POPITs must be connected for Points 129
to 247 to expansion loops connected to POPEX #2.
Two sheets of peel-off POPIT labels are supplied with
the D8125 POPEX Module. Use the sheet marked
“Bank1” for Points 9 to 127. Use the sheet marked
“Bank2” for Points 129 to 247.
Each label has two parts. Place the smaller part (with
only the point number) on the chip. Place the larger
part (with the switch settings) on the base of the
POPIT. Set the switches and cover the POPIT.
Do not program two POPITs for the same point
number. After programming all the points, perform a
Service Walk Test. The D9412GV2/D7412GV2/
D7212GV2 Installation and Troubleshooting Quick Reference
Guide (P/N: F01U003638) contains instructions for
performing a Service Walk Test. If a point does not
test, check the programming for a duplicated address.
Walk Test and Service Walk Test Do Not Show
Extra Points: If the point assignment switches on a
POPIT or OctoPOPIT are set incorrectly, it can create
both missing and extra points. If the same point
number is assigned to two or more POPITs or
OctoPOPITs, none of the points with that number test
correctly. Refer to Section 9.1 Point (Zonex) Bus:
D9412GV2 Terminals and D7412GV2 Terminals on page
34.
40
BFSK/
Relay
Debounce
___________________
D8128D OctoPOPIT Module
Modules D8128, D8128A, or D8128B are
incompatible with the D9412GV2 or
D7412GV2. Use only the D8128D
OctoPOPIT Module. Using Modules D8128,
D8128A, or D8128B can cause intermittent
Missing and Restoral Reports.
9.4.1
Description
The D8128D OctoPOPIT Module combines the
functions of the D8125 POPEX Module and the
D8127/D9127 POPIT Modules to provide eight offboard points in a single module. You can wire both
D8128D OctoPOPIT and D8125 POPEX Modules in
parallel to the Zonex Bus terminals on the same control
panel.
Review Section 6.0 Power Outputs on page 25 to ensure
there is enough power for the OctoPOPITs and other
powered devices that will be connected to the system.
Up to thirty D8128D Modules can be connected to the
D9412GV2 Control Panel. A maximum of nine
D8128Ds can be connected to the D7412GV2 Control
Panel (three points can be used on the last
OctoPOPIT).
9.4.2
Listings
The D8128D OctoPOPIT Module is UL Listed for
Local or Police Connected Burglary Alarm, Central
Station Burglary Alarm, Household Burglary Alarm
applications, and commercial fire applications (UL 864
and NFPA 72).
Bosch Security Systems, Inc. | 5/05 | F01U003641B
D9412GV2/D7412GV2 | Operation and Installation Guide | 9.0 Off-Board Points
.
The D8128D is also suitable for fire supervisory
applications, such as indicating circuit supervision
(using the D192C/D192G Bell Circuit Supervision
Module), sprinkler supervision, and valve tamper
protection.
9.4.3
For the most effective installation, use the following
four-step process:
1.
Set the OctoPOPIT switches. Refer to Section 9.4.4
Setting the OctoPOPIT Switches.
2.
Physically mount the OctoPOPIT in the enclosure.
Refer to Section 9.4.5 Mounting OctoPOPITs, page 42.
3.
Wire the OctoPOPIT. Refer to Section 9.4.6 Wiring
OctoPOPITs on page 42.
4.
Wire the OctoPOPIT sensor loops. Refer to Section
9.4.7 OctoPOPIT Sensor Loops on page 46.
Requirements for Fire Initiation Applications
Non-powered, fire initiating devices such as
pull-stations, heat detectors, and UL Listed
four-wire smoke detectors can be connected
directly to the point inputs on the D8128D.
The D125B Dual Powered Loop Interface Module or
the D129 Dual Class “A” Module zone outputs can be
connected directly to the point inputs on the D8128D.
Use the D125B to connect two-wire smoke detectors.
Typically, the D129 is used for connecting waterflow
switches.
The D125B or D129 and the OctoPOPIT can be
mounted in the same enclosure with the control panel
or in a separate enclosure connected to the control
panel’s enclosure by a conduit not more than 6 m
(20 ft.) in length.
Figure 15: D8128D OctoPOPIT Layout
1
Installation
9.4.4
Setting the OctoPOPIT Switches
The D8128D OctoPOPIT has two sets of DIP switches
(Figure 15). Use the DIP switches on the top of the unit
(with the terminal strip along the left edge) to set the
address for the OctoPOPIT. Use the DIP switches at
the bottom of the unit to enable or disable individual
points connected to the OctoPOPIT.
Address Switches
The switches on the D8128D OctoPOPIT set point
assignments and line termination. These switches are
easier to set before mounting the D8128D in the
enclosure.
Switches 1, 2, 3, and 4 assign the OctoPOPIT sensor
loops to point numbers on the control panel. Table 15
on page 42 shows the OctoPOPIT switch settings for
point assignments.
Switch 5 sets line termination. Refer to Table 16 on
page 42.
2
3
4
1 2 3 4 5 6 7 8
POINTS
1234-
Molex® connectors
Address DIP switches
Terminal strip
Point DIP switches
Bosch Security Systems, Inc. | 5/05 | F01U003641B
41
D9412GV2/D7412GV2 | Operation and Installation Guide | 9.0 Off-Board Points
Table 15:
D8128D OctoPOPIT Switch Settings
for D9412GV2 and D7412GV2
ZONEX 1
D8128D Address Switches
Points 9 to
127
3
4
ZONEX 2
5
Points 129
to 247
1
2
9 to 16
ON
ON
ON
ON
*
129 to 136
17 to 24
ON
ON
ON
OFF
*
137 to 144
25 to 32
ON
ON
OFF
ON
*
145 to 152
33 to 40
ON
ON
OFF
OFF
*
153 to 160
41 to 48
ON
OFF
ON
ON
*
161 to 168
49 to 56
ON
OFF
ON
OFF
*
169 to 176
57 to 64
ON
OFF
OFF
ON
*
177 to 184
65 to 72
ON
OFF
OFF
OFF
*
185 to 192
73 to 80
OFF
ON
ON
ON
*
193 to 200
81 to 88
OFF
ON
ON
OFF
*
201 to 208
89 to 96
OFF
ON
OFF
ON
*
209 to 216
97 to 104
OFF
ON
OFF
OFF
*
217 to 224
105 to 112
OFF
OFF
ON
ON
*
225 to 232
113 to 120
OFF
OFF
ON
OFF
*
233 to 240
121 to 127
OFF
OFF
OFF
ON
*
241 to 247
* Line Termination Switch
For the D8128D OctoPOPITs assigned to
Points 121 to 127, 241, and 247, set Point
Input Switch 8 to the OPEN position.
D9412GV2 uses Points 9 to 127 on Zonex
1 and Points 129 to 247 on Zonex 2.
D7412GV2 uses Points 9 to 75 on Zonex 1
only.
Table 16:
Switch 5 Settings for Line Termination
Is a D8125
POPEX Module
connected?
Zonex No.
No
NA
Yes
1
No
NA
Yes
2
Switch 5 Setting(s) on
D8128D OctoPOPIT(s)
Set Switch 5 of only
one D8128D to ON
Set Switch 5 of all
D8128Ds to OFF
Set Switch 5 of only
one D8128D to ON
Set Switch 5 of all
D8128Ds to OFF
Use the point DIP switches to disable conflicting
points, such as when a D9210B Access Control Module
must be assigned to a point that falls within the range
of the D8128D OctoPOPIT. In this example, a
D9210B is assigned to Point 20. On the same system, a
D8128D OctoPOPIT is assigned to Points 17 through
24. Moving the DIP switch for Point 4 to the OFF
position would effectively disable Point 20, allowing
normal operation of the D9210B and the OctoPOPIT.
Terminate each OctoPOPIT sensor loop with a 1 kΩ
EOL resistor. Attach a resistor even if you do not
enable the loop.
9.4.5
Mounting OctoPOPITs
The D8128D OctoPOPIT Module can be installed in
the enclosure with the control panel using standard
four-conductor 0.8 mm (22 AWG) wire, or in a
separate enclosure (Model D8103, D8103A, or D8109)
up to 61 m (200 ft.) from the control panel using
shielded (recommended) standard four-conductor
0.8 mm (22 AWG) wire. If using the D125B or D129,
refer to the Specifications section of the D8128D
Installation Guide (P/N: 41323) for cabling
requirements.
For UL Listed systems, mount the D8128D in a
tamper-proof enclosure. To install OctoPOPITs in the
control panel’s enclosure, complete the following
procedure. Use the D137 Mounting Bracket to install
OctoPOPITs in enclosures with no module-mounting
locations available.
1.
Align the OctoPOPIT module using any of the
four mounting locations in the enclosure. Refer to
Figure 2 on page 15.
2.
Use the screws provided with the module to secure
it in the enclosure.
9.4.6
Wiring OctoPOPITs
Warning: Disconnect all power to the
control panel before beginning any work
with the internal components. Serious injury
could result from electrical shock.
1.
Power down the control panel:
a. Disconnect the positive (red) battery lead at
the battery.
b. Unplug the transformer.
Point DIP Switches
Each point connected to the D8128D is enabled by
closing the respective DIP switch, or disabled by
opening the DIP switch. For example, to disable a
device connected to the P3 Terminal (Point 3), move
DIP switch number 3 to the OPEN position.
42
Bosch Security Systems, Inc. | 5/05 | F01U003641B
D9412GV2/D7412GV2 | Operation and Installation Guide | 9.0 Off-Board Points
.
A D8128D OctoPOPIT can be installed up
to 61 m (200 ft.) from the control panel.
2.
Connect the D8128D to the control panel:
• Wire the D8128D to the terminal strip on the
side of the POPEX Module (), or
®
• Connect the D8128D using the Molex
connectors (P1 and P2). Refer to Using Molex®
Connectors on page 46.
Caution - AC induction: Avoid installing
Zonex data wires and Zonex input (sensor
loop) wires around any AC conduit, wiring,
or electrical devices that emit fields of
electromagnetic interference (EMI).
Using the Terminal Strip
Refer to Table 17, Figure 16 on page 44, and Figure 17
on page 45 when using the terminal strip to connect the
D8128D OctoPOPIT to the control panel.
Table 17:
Terminal Strip Connections
D8128D
D9412GV2
D7412GV2
Common
Terminal 23
Terminal 23
Out
Zonex 1 = Terminal 27
Zonex 2 = Terminal 25
Zonex 1 = Terminal 28
Zonex 2 = Terminal 26
Terminal 24
Terminal 27
In
+12 V
Terminal 28
Terminal 24
Bosch Security Systems, Inc. | 5/05 | F01U003641B
43
D9412GV2/D7412GV2 | Operation and Installation Guide | 9.0 Off-Board Points
Figure 16: Connecting D8128D OctoPOPITs to the D9412GV2
5
1
Reset Pin
Disable All Except Battery
Charging And Programming
3
2
4
2
PERIPHERAL DEVICE CONNECTIONS
RED
POWER +
32
YELLOW
DATA BUS A
31
GREEN
DATA BUS B
30
COMMON
29
ZONEX OUT 1
28
ZONEX IN 1
27
ZONEX OUT 2
26
ZONEX IN 2
25
ZONEX POWER +
24
ZONEX COMMON
23
BLACK
N.F.P.A.
Style 3.5
Signaling
Line
Circuits
6
6
D5200/D5360
PROG CONN
Point 8
S3 Option
7
Closed = 1KΩ EOL
Normal Operation
11
Open =AB-12 UL
Bell Box 220 KΩ
21
22
GRN
9
8
8
10
12
6
1234567-
Zonex Bus 1, Switch 1 ON (Points 9 to 72)
Bus 1
First address on Zonex Bus 1
Last address on Zonex Bus 1
Zonex Bus 1, Switch 1 OFF (Points 73 to 127)
Sensor loops
Zonex Bus 2, Switch 1 ON (Points 129 to 192)
6
8910 11 -
Bus 2
First address on Zonex Bus 2
Last address on Zonex Bus 2
Zonex Bus 2, Switch 1 OFF (Points 193 to
240)
12 - On-board points
Refer to Address Switches in Section 9.4.4 Setting the OctoPOPIT Switches on page 41 for
information about making these switch settings.
44
Bosch Security Systems, Inc. | 5/05 | F01U003641B
D9412GV2/D7412GV2 | Operation and Installation Guide | 9.0 Off-Board Points
.
Figure 17: Connecting D8128D OctoPOPITs to the D7412GV2
1
2
1
2
Pin
Battery
amming
E CONNECTIONS
POWER +
1
32
DATA BUS A
31
DATA BUS B
30
COMMON
29
ZONEX OUT 1
28
ZONEX IN 1
27
NOT USED
26
2
NOT USED
25
NEX POWER +
24
COMMON
23
D5200/D5360
PROG CONN
1
2
1 - First address on Zonex Bus 1
2 - Sensor loops
Refer to Address Switches in Section 9.4.4 Setting the OctoPOPIT Switches on page 41 for
information about making these switch settings.
Bosch Security Systems, Inc. | 5/05 | F01U003641B
45
D9412GV2/D7412GV2 | Operation and Installation Guide | 9.0 Off-Board Points
®
Using Molex Connectors
Each D8128D Module is supplied with a 30 cm (12 in.) female-to-female Molex cable assembly.
P1 and P2 are Molex connectors that parallel the COM, IN, OUT, and +12 VDC terminals on the terminal strip.
In installations with multiple D8128Ds, use these connectors (as opposed to terminals) with the supplied cable;
however, when connecting D8128D Modules directly to the control panel, the terminal strip is easier to use.
The Molex connectors provided are "keyed" (Molex plug can only fit in one direction). Ensure the connector is
attached correctly: the red wire is on the bottom of P1 (or P2) and the black wire is on the top.
When connecting multiple D8128Ds to a control panel, you can connect the control panel terminals to P1 or the
COM, IN, OUT, and +12V terminals on the first D8128D. Then connect P2 of the first D8128D to P1 of the
second D8128D and so on (Figure 18).
®
Figure 18: Wiring Multiple D8128Ds Using Molex Connectors
3
P2
P2
P2
P1
P1
P1
1
2
9
28
27
26
COM IN OUT+12V
COM IN OUT+12V
COM IN OUT+12V
25
24
7
6
23
8
5
4
123459.4.7
D9412GV2 Control Panel
Yellow
Green
Black
Red
OctoPOPIT Sensor Loops
Only the resistance on the loop limits the number of
normally-open or normally-closed detection devices
each sensor loop can supervise. Resistance on each
sensor loop must be less than 100 Ω with the detection
devices connected.
Certain UL and NFPA applications can limit the
number of detection devices. Consult the appropriate
UL or NFPA standards.
The OctoPOPIT detects open, short, closed, normal,
and grounded circuit conditions on its sensor loops and
sends the conditions to the control panel. Each sensor
loop has an assigned point number and sends signals to
the control panel separately.
Use twisted-pair wire for the OctoPOPIT sensor loops
to avoid EMI problems. Run wires away from the
premises telephone and AC wiring. If you suspect a
noisy environment, use shielded cable.
46
6789-
First D8128D
Second D8128D
Third 8128D
Up to 15 per Zonex Bus
The OctoPOPIT has two rows of terminal numbers. In
the row nearest to the terminal blocks, the positive
outputs for the sensor loops are labeled P1 to P8.
Sensor loop outputs P1 and P2, P3 and P4, P5 and P6,
and P7 and P8 share common terminals. The common
terminals for each pair are labeled COM.
Terminate each OctoPOPIT sensor loop with a 1 kΩ
EOL resistor. Attach a resistor even if you do not
enable the loop. The OctoPOPIT includes a D105BL
resistor for each sensor loop. Refer to Figure 19 on page
47.
Do not duplicate point assignments. Points do not
function properly if assigned to an OctoPOPIT sensor
loop and a POPIT, to two OctoPOPIT sensor loops, or
to two POPITs.
Bosch Security Systems, Inc. | 5/05 | F01U003641B
D9412GV2/D7412GV2 | Operation and Installation Guide | 9.0 Off-Board Points
.
Figure 19: D8128D OctoPOPIT Sensor Loops
1
COM IN OUT+12V P1 COM P2
P3 COM P4 P5 COM P6
2
P7 COM P8
3
4
5
12345-
9.5
D8128D OctoPOPIT
To control panel
To additional OctoPOPIT sensor loops
OctoPOPIT sensor loops
1 kΩ EOL resistor (P/N: P105BL, package of
eight)
Testing Off-Board Points
Use the Service Walk Test to test off-board points.
Refer to the D9412GV2/D7412GV2/D7212GV2
Installation and Troubleshooting Quick Reference Guide
(P/N: F01U003638) for instructions. Test to ensure that
all off-board points operate properly.
Walk Test and Service Walk Test Do Not Show
Extra Points: If the point assignment switches on a
POPIT or OctoPOPIT are set incorrectly, missing and
extra points can occur. If the same point number is
assigned to two or more POPITs or OctoPOPITs, none
of the points with that number test correctly. Refer to
Section 9.1 Point (Zonex) Bus: D9412GV2 Terminals and
D7412GV2 Terminals on page 34.
Bosch Security Systems, Inc. | 5/05 | F01U003641B
47
D9412GV2/D7412GV2 | Operation and Installation Guide | 10.0 Off-Board Relays
10.0 Off-Board Relays
10.1
D8129 OctoRelay
Use the D8129 OctoRelay to add relay outputs to the
system in groups of eight. On the D9412GV2, up to
128 OctoRelay outputs (relay numbers 1 to 128) can be
added to the system using 16 OctoRelays. D7412GV2
allows up to 64 relay outputs. Review Section 6.0 Power
Outputs on page 25 to ensure that enough power is
provided for the OctoRelays and other powered
devices that are connected to the system.
Alarm output, auxiliary relay, sensor reset, arming
status, point status, alarm memory, or remote functions
can be assigned to the OctoRelay outputs individually.
Refer to Relay Parameters in the D9412GV2/D7412GV2
Program Entry Guide (P/N: F01U003635) for
programming details.
D8129 Restricted for Fire Systems: D8129 relay
outputs are not supervised and cannot be used in fire
or combined fire and burglary installations for primary
indicating devices.
OctoRelays for relay numbers 1 to 64 connect to
Zonex 1, Terminal 28. OctoRelays for relay numbers
65 to 128 connect to Zonex 2 (D9412GV2 only),
Terminal 26 on the D9412GV2. Refer to Figure 20 on
this page and Figure 21 on page 49.
Figure 20: D8129 Connections to the D9412GV2
Reset Pin
Disable All Except Battery
Charging And Programming
PERIPHERAL DEVICE CONNECTIONS
POWER +
32
YELLOW
DATA BUS A
31
GREEN
DATA BUS B
30
COMMON
29
ZONEX OUT 1
28
RED
BLACK
N.F.P.A.
Style 3.5
Signaling
Line
Circuits
ZONEX IN 1
27
ZONEX OUT 2
26
ZONEX IN 2
25
ZONEX POWER +
24
ZONEX COMMON
23
4
GND
AUX
DATA
3
1
4
5
6
7 8
5
6
7 8
4
Closed = 1KΩ EOL
Normal Operation
3
GND
AUX
DATA
Open =AB-12 UL
Bell Box 220 KΩ
22
3
D5200/D5360
PROG CONN
Point 8
S3 Option
21
2
1
GRN
1
2
2
3
4
5
1 - D8129 OctoRelays for relay numbers 1 to 64.
Connect OctoRelays in parallel.
2 - D8129 OctoRelays for relay numbers 65 to 128.
Connect OctoRelays in parallel.
48
3 - Power limited
4 - Supervised, power limited
5 - On-board points
Bosch Security Systems, Inc. | 5/05 | F01U003641B
D9412GV2/D7412GV2 | Operation and Installation Guide | 10.0
Off-Board Relays
.
Figure 21: D8129 Connections to the D7412GV2
Pin
Battery
amming
E CONNECTIONS
POWER +
32
DATA BUS A
31
DATA BUS B
30
COMMON
29
ZONEX OUT 1
28
ZONEX IN 1
27
NOT USED
26
NOT USED
25
EX POWER +
24
X COMMON
23
D5200/D5360
PROG CONN
2
3
1 - D8129 OctoRelays for relay numbers 1 to 64.
Connect OctoRelays in parallel.
10.1.1 Configuring the D8129 OctoRelay
Five switches on the OctoRelay determine the relay
numbers for the eight relay outputs (Error! Reference
source not found.).
Table 18:
GND
AUX
DATA
3
D8129 OctoRelay Switch Settings
Panel Relay
Number
D8129 OctoRelay
Switch Setting
On Panel, Connect
D8129 to:
1 to 8
Off-On-On-On-On
Zonex 1 Terminal 28
9 to 16
On-Off-On-On-On
Zonex 1 Terminal 28
17 to 24
Off-Off-On-On-On
Zonex 1 Terminal 28
25 to 32
On-On-Off-On-On
Zonex 1 Terminal 28
33 to 40
Off-On-Off-On-On
Zonex 1 Terminal 28
41 to 48
On-Off-Off-On-On
Zonex 1 Terminal 28
49 to 56
Off-Off-Off-On-On
Zonex 1 Terminal 28
57 to 64
On-On-On-Off-On
Zonex 1 Terminal 28
D7412G Maximum
65 to 72
Off-On-On-On-On
Zonex 2 Terminal 26
73 to 80
On-Off-On-On-On
Zonex 2 Terminal 26
81 to 88
Off-Off-On-On-On
Zonex 2 Terminal 26
89 to 96
On-On-Off-On-On
Zonex 2 Terminal 26
97 to 104
Off-On-Off-On-On
Zonex 2 Terminal 26
105 to 112
On-Off-Off-On-On
Zonex 2 Terminal 26
113 to 120
Off-Off-Off-On-On
Zonex 2 Terminal 26
121 to 128
On-On-On-Off-On
Zonex 2 Terminal 26
Bosch Security Systems, Inc. | 5/05 | F01U003641B
1
2
1
3
4
5
6
7 8
2 - Power limited
3 - Supervised, power limited
10.1.2 Relay Outputs
Relay outputs can activate when you are
setting the OctoRelay switches or
programming the control panel.
Disconnect equipment connected to relay
outputs when you perform these functions.
Each OctoRelay output provides a Form C dry contact
rated for 1.0 A at 12 VDC. Normally-open, common,
and normally-closed terminals are available for each
relay output. When an individual output is activated,
there is continuity between the normally-open and
common terminals. When the output is not activated,
there is continuity between the normally-closed and
common terminals.
10.1.3 Installation
Set the switches on the OctoRelay before installing it in
the enclosure. Refer to Section 10.1.1 Configuring the
D8129 OctoRelay on this page.
Install the OctoRelay in the enclosure with the control
panel (Figure 2 on page 9) or in an adjacent enclosure
that is no more than 1.5 m (5 ft.) from the control
panel. Use 1.5 mm (16 AWG) to 0.8 mm (22 AWG)
wire.
49
D9412GV2/D7412GV2 | Operation and Installation Guide | 10.0 Off-Board Relays
To install OctoRelays in the enclosure with the control
panel:
1. Align the module with one of the mounting
locations in the enclosure (refer to Figure 2 on
page 9).
2.
Using the screws provided with the module, secure
the module in the enclosure.
Table 19: Number of D8128Ds Used with
D8129s
If the number of
D8128Ds connected to a
single Zonex bus is:
Do not connect more than
this number of D8129s:
Use the D137 Mounting Bracket or D9002
Mounting Skirt to install OctoRelays in enclosures
with no available module mounting locations.
10.1.4 Wiring Connections
Power down the control panel to connect OctoRelays.
Refer to Figure 20 on page 48 and Figure 21 on page 49.
OctoRelays for Relays 1 to 64 connect to
Zonex 1, Terminal 28.
OctoRelays for Relays 65 to 128 connect
to Zonex 2, Terminal 26 on the D9412GV2
only.
Only one OctoRelay is shown wired to each Zonex bus
in Figure 20 on page 48and Figure 21 on page 49. Wire
additional OctoRelays in parallel. Review Section 6.0
Power Outputs on page 25 for information about
providing enough power for the relays.
The number of D8129 OctoRelays that can be
connected to each Zonex terminal on the D9412GV2
control panels is limited by the number of D8128D
OctoPOPITs connected.
Using D8129 OctoRelays and D8128D
OctoPOPITs together on the same Zonex
terminals is limited and depends on the
number of D8128 OctoPOPITs and D8129
OctoRelays connected to a single Zonex
Bus.
Refer to Table 19 for information about the
maximum number of D8128Ds and
D8129s you can connect to a single Zonex
bus.
10.2
9
6
10
11
12
13
5
4
3
1
14
1
D811 Arm Status Relay Module
The D811 Arm Status Relay Module allows the
addition of a single off-board relay output to the
system. Alarm output, auxiliary relay, sensor reset,
arming status, point status, alarm memory, or remote
functions can be assigned to the D811 relay output. It is
not restricted to the Arming Status Mode only.
Relay Numbers for D811 Not Programmable: If the
D811 is connected to Zonex 1, Terminal 28, use relay
number 53 for the relay output. If the D811 is
connected to Zonex 2, Terminal 26 on the D9412GV2,
use relay number 117 for the relay output.
D811 Modules connect as shown in Figure 22 on page
51and Figure 23 on page 52. Review Section 6.0 Power
Outputs on page 25 to ensure that enough power is
provided for the powered devices that connect to the
system. Refer to Relay Parameters in the
D9412GV2/D7412GV2 Program Entry Guide
(P/N: F01U003636) for programming details.
D811 Restricted for Fire Systems: The D811 relay
output is not supervised and cannot be used in fire or
combined fire and burglary installations for primary
indication devices.
10.2.1 Relay Output
Relay outputs can activate when you are
programming the control panel.
Disconnect equipment connected to relay
outputs when you perform this function.
Each D811 relay output provides a Form C dry contact
rated for 1.0 A at 12 VDC. Normally-open, common,
and normally-closed terminals are available. When an
individual output is activated, continuity exists between
the normally-open and common terminals. When the
output is not activated, continuity exists between the
normally-closed and common terminals.
50
Bosch Security Systems, Inc. | 5/05 | F01U003641B
D9412GV2/D7412GV2 | Operation and Installation Guide | 10.0
.
10.2.2 Installation
Install the D811 in the enclosure with the control panel
(Figure 22) or in an adjacent enclosure no more than
1.5 m (5 ft.) from the control panel. Use 1.5 mm
(16 AWG) to 0.8 mm (22 AWG) wire.
To install D811 Modules in the enclosure with the
control panel:
1.
2.
Align the D811 Module with any of the four
mounting locations in the enclosure (Figure 2 on
page 15).
Off-Board Relays
Use the D137 Mounting Bracket or D9002
Mounting Skirt to install D811 Modules in
enclosures with no available module mounting
locations.
10.2.3 Wiring Connections
Power down the control panel to connect D811
Modules as shown in Figure 22 on this page and
Figure 23 on page 52.
The D811 for Relay 53 connects to
Zonex 1.
Using the screws provided with the module, secure
it in the enclosure.
The D811 for Relay 117 connects to
Zonex 2 on the D9412GV2.
Figure 22: D811 Module Wiring to the D9412GV2
Reset Pin
Disable All Except Battery
Charging And Programming
PERIPHERAL DEVICE CONNECTIONS
RED
POWER +
32
YELLOW
DATA BUS A
31
GREEN
DATA BUS B
30
COMMON
29
ZONEX OUT 1
28
ZONEX IN 1
27
ZONEX OUT 2
26
BLACK
N.F.P.A.
Style 3.5
Signaling
Line
Circuits
ZONEX IN 2
25
ZONEX POWER +
24
ZONEX COMMON
23
5
DATA
AUX
GND
5
D5200/D5360
PROG CONN
Point 8
S3 Option
Closed = 1KΩ EOL
Normal Operation
DATA
AUX
GND
Open =AB-12 UL
Bell Box 220 KΩ
21
22
1
GRN
2
3
1 - D811 for Relay 53
2- D811 for Relay 117
Bosch Security Systems, Inc. | 5/05 | F01U003641B
3-
On-board points
51
D9412GV2/D7412GV2 | Operation and Installation Guide | 10.0 Off-Board Relays
Figure 23: D811 Module Wiring to the D7412GV2
Pin
Battery
amming
E CONNECTIONS
POWER +
32
DATA BUS A
31
DATA BUS B
30
COMMON
29
ZONEX OUT 1
28
ZONEX IN 1
27
5
NOT USED
26
NOT USED
25
EX POWER +
24
AUX
X COMMON
23
GND
DATA
1
D5200/D5360
PROG CONN
1 - D811 for Relay 53
52
Bosch Security Systems, Inc. | 5/05 | F01U003641B
D9412GV2/D7412GV2 | Operation and Installation Guide | 11.0
Arming Devices
.
11.2.1 Assigning an Address for the Keypad
11.0 Arming Devices
11.1
Description
Keypads, maintained or momentary contact
keyswitches, or a combination of the two are used to
arm and disarm areas. The control panel can contain
up to eight areas. Refer to 3.3.6 Areas and Accounts on
page 12 for a description of areas.
11.2
Keypad Terminals 29 to 32
The Bosch Security Systems keypad is a four-wire
powered device used to arm and disarm areas,
annunciate complete system status, initiate system tests,
and control many functions of the security system.
A total of 32 unsupervised keypads can be connected
to the system. The number of supervised keypads,
number of areas, and the available power affect the
total number of keypads that can be connected to the
system. Refer to Keypad in the D9412GV2/D7412GV2
Program Entry Guide (P/N: F01U003636) for complete
programming details on keypad options.
Five types of keypads are available for use with the
system.
•
•
•
•
•
D1255 − 16-character alphanumeric display for
general use.
D1256 − text display keypad with keys designated
for local fire alarm control.
D1257 − text display keypad for fire annunciation.
D1260 − easy-to-read, 4-line by 20-character LCD
display with eight “soft” keys to display simple
selections.
D720 − LED display keypad appropriate for use as
a single area keypad with up to eight points.
D1255 and D720 are available in white
(D1255W and D720W) or red (D1255R
and D720R).
Table 20 shows the correct switch setting for each
address.
Table 20:
Address
Keypad Address Settings
Switch
1
2
3
4
Address #1
Address #2
Address #3
ON
OFF
ON
ON
ON
OFF
ON
ON
ON
ON
ON
ON
Address #4
Address #5
OFF
ON
OFF
ON
ON
OFF
ON
ON
Address #6
Address #7
OFF
ON
ON
OFF
OFF
OFF
ON
ON
Address #8
OFF
OFF
OFF
ON
5
Encoding
Tone ON/OFF
The system can supervise up to eight keypads. The
control panel sends a Serial Device Trouble Report,
SDI FAILURE, in the Modem IIIa2 format or
TROUBLE ZN D in the BFSK format, if it loses
communication with a supervised keypad. CALL FOR
SERVICE appears in any keypad that loses
communication with the control panel, if the keypad
has text display capability. SERVC KEYPAD appears at
all other keypads connected to the system.
Switches on the keypad assign an address (1 to 8). The
address determines if the keypad is supervised, the
scope of the keypad, and to what area the keypad is
assigned. Refer to Keypad Assignment in the
D9412GV2/D7412GV2 Program Entry Guide
(P/N: F01U003636) for a complete description of
addresses.
6
ON
ON
ON
ON
ON
ON
ON
ON
11.2.2 Installation
Refer to the keypad installation manuals for installation
and mounting instructions. Keypads connect to the
control panel in parallel (Table 21).
Table 21:
Keypad Connections
D7212GV2
Terminal
Function
Keypad
Wire Color
Function
32*
31
30
29
POWER +
DATA BUS A
DATA BUS B
COMMON
Red
Yellow
Green
Black
12 VDC
Data – In
Data – Out
Common
* Connect with at least 1.5 m (5 ft.) or 0.8 mm (22 AWG) wire
(4.3 m [14 ft.] of 1.2 mm [18 AWG] wire).
Switching the Green and Yellow Wires Affects
Other Keypads: Connecting the green wire
incorrectly from the keypad to Terminal 31 and the
yellow wire to Terminal 30 causes other keypads
connected to the control panel to go blank or to sound
random beep tones.
For operational information, refer to the user’s guide
for the specific keypad.
Bosch Security Systems, Inc. | 5/05 | F01U003641B
53
D9412GV2/D7412GV2 | Operation and Installation Guide | 11.0 Arming Devices
You can connect devices to the data bus (Terminals 30
and 31) by parallel wire run from the control panel to
each device, wire from device to device, or a
combination of the two using a maximum of 4572 m
(15000 ft) of 0.8 mm (22 AWG) wire for all devices
connected to the SDI Bus combined.
Wire Limits for Individual Keypads
• Limit most keypads to 610 m (2000 ft) per run.
• Limit D9210B Modules to 457 m (1500 ft) per run
(762 m [2,500 ft] if using an external power
supply).
• Limit D9131A Modules to 305 m (1000 ft) per run.
Extra Power for More Keypads
The D1255 Command Center draws 104 mA when
idle. It draws 206 mA with the keys lit and the sounder
activated. Review Section 6.0 Power Outputs on page 25
to determine the total power output requirements for
the system.
One or more D8132 Battery Charger/Power Supply
Modules can be added for the number of keypads
used. Figure 24 shows the D8132 powering keypads in a
stand-alone configuration.
The control panel and the D8132 (or
other power supply) must share
COMMON.
Figure 24 shows the common form of the
D8132 Module connected to the common
on the keypad and the common on the
control panel. Any stand-alone power
supply, powering any device connected to
the control panel, must also be connected
to a common terminal on the control panel.
If using the ground fault detection capability
on the D9412GV2 and D7412GV2
Control Panels with an external power
supply, ensure that the external selected
power supply isolates its earth ground
connection from the negative side of the
auxiliary power output. External power
supplies that do not isolate earth ground
can cause ground fault conditions on the
control panel.
For UL Certificated accounts, use a UL Listed auxiliary
12 VDC or 24 VDC regulated, power-limited power
supply for Fire Protective Signaling Units and
Commercial or Residential Burglar Units. The D8132
is not UL Listed as a stand-alone power supply.
Figure 24: Power at Keypads
5
1
2
3
2
4
3
4
1 - To control panel
2 - +12 VDC
3 - Data
54
4 - Common
5 - D8132 or external power supply
Bosch Security Systems, Inc. | 5/05 | F01U003641B
D9412GV2/D7412GV2 | Operation and Installation Guide | 11.0
Arming Devices
.
11.3
D268/D269 Independent Zone
Control, D279A Independent Zone
Control
Any on-board or OctoPOPIT point can be
programmed so that the D268/D269 or D279A
Independent Zone Control operates as independent
point control (arming and disarming the point).
Refer to Point Assignments in the D7212GV2 Program
Entry Guide (P/N: F01U003636) for programming
information. Refer to the D268/D269 Operation and
Installation Instructions (P/N: 74-004758-000) or the
D279A Operation and Installation Instructions (P/N:
46458) for wiring and operation instructions.
11.4
Keyswitch
11.4.2 Programming
Refer to Point Assignments in the D9412GV2/D7412GV2
Program Entry Guide (P/N: F01U003636) for the correct
programming for points used for keyswitches.
11.4.3 Installation
For maintained switches, connect the EOL resistor for
the point at the keyswitch so that the switch opens the
circuit when it operates. A short on the circuit produces
an alarm if the area is armed and a trouble if it is
disarmed. Refer to Figure 25.
For momentary keyswitches, connect the EOL resistor
at the keyswitch point so that when the keyswitch
operates, it shorts the resistor. An open on the circuit
causes an alarm if the area is armed and a trouble if it
is disarmed. Refer to Figure 25.
11.4.1 Description
A maintained or momentary contact arming station
(keyswitch) can be connected to master arm or disarm
any of the areas in the system. The keyswitch is
connected to an on-board or off-board point’s sensor
loop. Relays can be programmed to activate arming
status LEDs for keyswitch arming stations. Refer to
Relays in the D9412GV2/D7412GV2 Program Entry Guide
(P/N: F01U003636)
Figure 25: Keyswitch Wiring
2
1
6
7
3
3
5
4
1234∗
Maintained keyswitch
Momentary keyswitch
Common
Point input
5
4
5 - 1 kΩ or 33 kΩ resistor ∗
6- Open on a circuit arms the area
7 - Short on a circuit toggles the arming state
Use 1 kΩ EOL resistors if using one of the zones on the control panel or an OctoPOPIT. Use a 33 kΩ resistor if using a POPIT.
Maintained Contact
If the point to which the keyswitch is connected is programmed for a maintained contact, an open on the arming
circuit arms the area. All faulted points are force armed, regardless of the entry in the FA Bypass Max program
item. Returning the circuit to normal disarms the area. Refer to Area Parameters and Point Assignments in the D7212
Program Entry Guide
(P/N: F01U003804)
Bosch Security Systems, Inc. | 5/05 | F01U003641B
55
D9412GV2/D7412GV2 | Operation and Installation Guide | 11.0 Arming Devices
Momentary Contact
If the point to which the keyswitch is connected is programmed for a momentary contact, shorting the arming
circuit toggles the area’s arming state between armed and disarmed. All faulted points are force armed, regardless
of the entry in the FA Bypass Max program item. Refer to Point Assignments in the D9412GV2/D7412GV2 Program
Entry Guide (P/N: F01U003636).
Silencing the Bell
To silence the bell (stop Alarm Bell output) if the system is armed, position the keyswitch to disarm the area. If the
area is disarmed, turn the keyswitch once to start the arming process. Turning the keyswitch a second time stops
the arming process and silences the bell.
56
Bosch Security Systems, Inc. | 5/05 | F01U003641B
D9412GV2/D7412GV2 | Operation and Installation Guide | 12.0
SDI Devices
.
12.3.1 Switch Settings
12.0 SDI Devices
12.1
Description
D9412GV2 or D7412GV2 Control Panels can support
a number of accessory devices from the SDI Bus using
Terminals 29 through 32. Some devices include the
D1255 Command Center (keypad) (refer to Section 11.0
Arming Devices on page 53), D9131A Parallel Printer
Interface Module, D9210B Wiegand Control Interface
Module, DX4010i RS-232 Serial Interface Module,
D9133 Serial Interface Module, DX4020 Network
Interface Module, and D9133TTL-E Network Interface
Module.
12.2
Switches on the D9131A assign a unique address (17 to
19) for each printer. The address determines if the
printer is supervised, the area scope of the printers, and
the area to which the printer is assigned. Refer to
Printer Parameters in the D9412GV2/D7412GV2 Program
Entry Guide (P/N: F01U003636) for a complete
description of addresses.
Table 23 shows the correct switch setting for each
address.
Table 23:
Printer
Installation
For complete installation instructions, consult the
operation and installation guide for the specific SDI
device. SDI devices connect to the control panel in
parallel (Table 22).
17
18 1
These devices can share power with the control panel
or be powered by a stand-alone power source.
2
Table 22:
1
1
Switch
1
2
3
4
ON
OFF
ON
ON
ON
ON
ON
OFF
ON
2
5
6
ON
ON
ON
ON
ON
ON
ON
ON
ON
D9412GV2 only.
Switch 4:
ON = Header and form feed
OFF = No header and form feed
12.3.2 Supervision
SDI Device Connections
D9412GV2/D7412GV2
SDI Devices
Terminal
Function
Wire Color
Function
32
31
POWER +
DATA BUS 1
Red
Yellow
+12 VDC
Data – In
30
29
DATABUS B
COMMON
Green
Black
Data – Out
Common
A stand-alone power supply powering the
SDI device must also be connected to a
common terminal on the control panel.
Do not connect the earth ground for the
stand-alone power supply to Terminal 10
on the control panel.
12.3
19
Printer Address Switch Settings
D9131A Parallel Printer Interface
Module
The Bosch Security Systems D9131A Parallel Printer
Interface Module is a four-wire powered device used to
connect a standard parallel printer to a control panel.
D9412GV2 can supervise three printers and
D7412GV2 can supervise one printer. A separate
D9131A Parallel Printer Interface Module is necessary
for each printer. The D9131A connects to the printer
using a standard parallel printer cable.
Bosch Security Systems, Inc. | 5/05 | F01U003641B
Supervision includes:
• Proper operation of the SDI bus
• Proper connection of the printer cable between the
printer and the D9131A
• Printer paper supply
• Printer selected (on-line)
• Printer power.
The control panel sends an SDI Failure Report to the
receiver if communication with the printer interface
fails. If an SDI failure occurs, SERVC PRINTER
appears at the keypad. The report to the receiver
includes the address of the troubled D9131A to
indicate which printer needs service.
If an SDI device is supervised and Terminal SDI A
becomes disconnected, the device can continue to
operate normally, depending upon environmental
conditions.
12.4
D9210B Wiegand Control Interface
Module
The Bosch Security Systems D9210B Wiegand Control
Interface Module is a four-wire powered device
providing connections for an access door point and
door strike. The D9412GV2 can supervise eight
Wiegand Control Modules, the D7412GV2 can
supervise two. Each D9210B supports one door to
control access. Programming allows each access door
to be configured independently.
57
D9412GV2/D7412GV2 | Operation and Installation Guide | 12.0 SDI Devices
12.4.1 Access
Using Wiegand style cards or tokens, the D9210B can
allow access for up to 996 cards or tokens on the
D9412GV2, and up to 396 on the D7412GV2. User
access authority can be configured to restrict access to
certain doors or to certain periods of time. The reading
of access cards, in addition to granting access, can
control whether the system disarms. Used with the
D9412GV2, the D9210B recognizes 249 master users
by user name, passcode, and access authority. The
D9210B recognizes 99 master users when used with the
D7412GV2. Each master user supports three sub-users
with unique cards or tokens having the same access
level as the master user.
12.4.2 Switch Settings
Switches on the D9210B assign a unique address (1 to
8) to each module. Table 24 shows the correct switch
setting for each D9210B address.
Table 24:
Address Switch Settings for
Access Control Module
Door Module
Addresses
1
2
DIP Switch Settings
3
1
2
ON
OFF
ON
ON
ON
ON
4
1
52
62
ON
ON
ON
ON
---------------D7412GV2 Maximum---------------
1
3
ON
OFF
ON
ON
ON
4
5
6
7
8
OFF
ON
OFF
ON
OFF
OFF
ON
ON
OFF
OFF
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
Switch 4, Fail Safe Mode:
12.5
SDI Address 80
SDI Address 80, available on the D9412GV2 and
D7412GV2 Control Panels, allows for two-way SDI to
RS-232 information. This address is used with home or
building automation software. A D9133 Serial Interface
Module is required for this application.
12.5.1 Serial Interface Modules (SIMs)
The DX4010i RS-232 Serial Interface Module and the
D9133 Serial Interface Module are four-wire powered
SDI devices that provide connection for RS-232
devices to the D9412GV2 and D7412GV2 Control
Panels. They use a specific communication protocol
that is provided upon request. Contact Bosch Security
Systems Technical Support Monday through Friday
from 5 AM to 5 PM EST at 888-886-6189.
The DX4010i can be installed up to 305 m (1000 ft.)
from the control panel, using 0.8 mm (22 AWG) wire.
The DX4010i was not investigated by UL. Do not use
DX4010i in UL Listed installations.
The D9133 can be installed up to 305 m (1000 ft.) from
the control panel using 1.2 mm (18 AWG) wire. The
D9133 was not investigated by UL. Do not use D9133
in UL Listed installations.
12.5.2 Address Settings
No jumper settings are required for the D9133 (SDI
Address 80) for home or building automation purposes
(Figure 26). Remove the jumper shunts for this purpose.
Figure 26: D9133 Jumper Setting for Address 80
1
2
3
4
80
ON = If SDI bus fails, relay energizes.
OFF = If SDI bus fails, relay de-energizes.
2
Switches 5 and 6 must remain in the ON position.
The DX4010i has specific DIP switch settings for SDI
Address 80 when home or building automation is
desired. Figure 27 on page 59 shows the correct settings
for Address 80.
58
Bosch Security Systems, Inc. | 5/05 | F01U003641B
D9412GV2/D7412GV2 | Operation and Installation Guide | 12.0
SDI Devices
.
2.
Figure 27: DX4020i DIP Switch Settings
LED
ENABLE
Rx Tx
BUS
1
Tx Rx
SER
P2
P6
P1
DB9 GND
ENABLE
P3
3.
Connect D9133DC to Com Port 1 or Com Port 2
on the PC. The D9133DC has a DB-9 female serial
connector. A null-modem cable must be purchased
separately to connect the D9133DC to a PC.
Using 0.8 mm (22 AWG) or 1.2 mm (18 AWG)
wire, connect the D9133DC SDI terminals (SDI
PWR, SDI A, SDI B, and SDI COM) to the
control panel’s SDI terminals (Terminals 29 to 32).
To send or receive the control panel’s program, place
the Reset Pin in the Locked or Unlocked position.
ON
3
2
1
2
3
4
5
6
1
2
4
8
16
32
7
8
64 128
Locking the Reset Pin when programming
the control panel improves the uploading
and downloading times.
4
1234-
Address DIP switches
OFF position
ON position
SDI Address 80 switch settings
12.5.3 Supervision
Supervision of the serial interface module is available
through programming. Supervision is not required to
use a DX4010i or a D9133.
If supervised, and the serial interface module does not
respond to control panel supervision polls, the control
panel sends an SDI Failure Report to the receiver. If it
fails to communicate with the DX4010i or the D9133,
SERVC SDI 80 displays at the keypad. The SDI
Failure Report includes the address of the troubled
module indicating which module needs service.
12.6
SDI Address 88
SDI Address 88 is available with the D9412GV2 and
D7412GV2 Control Panels and is used for several
different applications. When using SDI Address 88,
connect only one listed device at a time.
Used as an External Modem
The D9133DC can operate as an external modem
when using Remote Programming Software (RPS) with
the control panel. Refer to the D9412GV2/D7412GV2
Program Entry Guide (P/N: F01U003636) for
programming details.
12.6.2 Network Interface Modules
The Bosch Security Systems DX4020 Network
Interface Module and D9133TTL-E Network Interface
Module are four-wire powered SDI devices that
provide connection for two-way communication over
Ethernet networks to D9412GV2 and D7412GV2.
For programming information on enhanced
communications, refer to the D9412GV2/D7412GV2
Program Entry Guide (P/N: F01U003636).
The DX4020 can be installed up to 305 m (1000 ft)
from the control panel using 0.8 mm (22 AWG) wire.
The D9133TTL-E can be installed up to 305 m
(1000 ft) from the control panel using 1.2 mm
(18 AWG) wire.
12.6.1 D9133DC Direct Connect Programming
Module
Use the D9133DC Direct Connect Programming
Module to handle local programming of the
D9412GV2 and D7412GV2 Control Panels. In
addition, the D9133DC allows diagnostic and history
retrieval. D9133DC is not UL Listed.
Connecting the D9133DC
1. Configure D9133DC for SDI Address 88. To
program the control panel when the reset pin is in
the unlocked position, program Enable SDI RPS to
Yes in the GV2AUX handler.
Bosch Security Systems, Inc. | 5/05 | F01U003641B
59
D9412GV2/D7412GV2 | Operation and Installation Guide | 12.0 SDI Devices
12.6.3 Address Settings
The DX4020 has specific DIP switch settings for SDI
Address 88 when using the DX4020 for Remote
Programming Software (RPS) or enhanced
communications in a LAN or WAN environment.
Refer to Figure 28 for the correct switch settings.
Figure 28: DX4020 DIP Switch Settings
R
Y
G
B
1
OPEN
=
=
1 2 3 4 5 6 7 8
2
1234-
= Switch is not used
4
3
DIP Switches
ON position
OFF position
SDE Address 88 switch settings
Place a jumper over Pin 8 for the D9133TTL-E (SDI
Address 88) to be used for RPS or enhanced
communications in a LAN or WAN environment.
Figure 29: D9133TTL-E Jumper Setting for
Address 88
1
2
3
4
88
12.6.4 Supervision
Supervision of the D9133DC, D9133TTL-E, and
D9133TTL-TR at SDI Address 88 is available through
programming that ensures operation between the
module and the control panel.
If supervised and the module does not respond to
control panel supervision polls, SERVC SDI 88
appears at the keypad. The report to the receiver
includes the address of the troubled module indicating
which module needs service.
60
Bosch Security Systems, Inc. | 5/05 | F01U003641B
D9412GV2/D7412GV2 | Operation and Installation Guide | 13.0
Programmer and Accessory Connections
.
13.0 Programmer and Accessory
Connections
13.1
Programmer Connector
Refer to the D5200 Operation Manual
(P/N: 74-06176-000) for complete information on using
the D5200 programmer.
To connect and disconnect the programmer:
1. Lock the Reset Pin (Figure 30).
2. Connect the D5200 Data/Power cord to the
programming connector on the control panel
(Figure 31).
3. Perform the desired programming function (send
or receive program).
4. Disconnect the programmer.
13.3
Accessory Connector
Use the accessory connector to connect the control
panel to the D928 Dual Phone Line Switcher. The
accessory connector is on the bottom right corner of
the I/O board (Figure 31). The D928 lets the control
panel use two telephone lines to send reports.
Refer to Section 7.11 D928 Dual Phone Line Switcher on
page 29 for installation and operating instructions.
Figure 31: Programmer and Accessory
Connections
26
Figure 30: Reset Pin
NEX IN 2
25
NEX POWER +
24
ONEX COMMON
23
D5200/D5360
PROG CONN
1
GRN
Reset Pin
Disable All Except Battery
Charging And Programming
PERIPHERAL DEVICE CONNECTIONS
POWER +
32
YELLOW
DATA BUS A
31
GREEN
DATA BUS B
30
BLACK
COMMON
29
RED
2
1
2
1 - Accessory connector
2 - Programming connector
1 - Reset Pin locked (closed)
2 - Reset Pin normal (open) for normal control
panel operation
13.2
Programmer Access Reports
When a program is sent to the control panel, the
control panel sends a Prog Access OK report 10
seconds after the handler exits or when the
programmer disconnects. The prompt in routing must
be programmed Yes to send this report.
Bosch Security Systems, Inc. | 5/05 | F01U003641B
61
D9412GV2/D7412GV2 | Operation and Installation Guide | 14.0 Faceplates
14.0 Faceplates
14.1
D9412GV2 Faceplate
Figure 32: D9412GV2 Faceplate
F01U003643B
LEDs Off When Normal
D9412GV2
YEL
Charging Status
RED
Low Battery - 12.1 VDC
1
2
10.2 VDC - Battery Load Shed
Digital Alarm Communicator Transmitter
Refer to D9412GV2/D7412GV2 Approved Applications Compliance Guide (P/N: F01U003639___)
For System Wiring Diagram, Issue A
Refer to D9412GV2/D7412GV2 Approved Applications Compliance Guide (P/N: F01U003639___)
For Compatible Smoke Detectors
CLASS 2 TRANSFORMER
16.5 VAC 40 VA 60 Hz
Model D1640
Internally Fused - Do not short
Requires Unswitched Outlet
Do not share with other equipment
CAUTION: See D9412GV2/D7412GV2 Operation and Installation Guide
+ AUX POWER
(P/N: F01U003641) for Power Requirements relating to Terminals 6 and 7 .
BATTERY NEGATIVE ONLY
CAUTION: Avoid damage to Panel.
Do not connect 24 V to terminals.
Maximum charging current 1.4 A
BATTERY POSITIVE ONLY
PROGRAMMABLE
ALARM OUTPUTS
Terminals
6 and 7
RELAY A
RELAY B
3
SWITCHED AUX
Terminal
8
RELAY C
POWER SUPPLY REQUIREMENTS
The Power Supply provides a maximum of 1.4 Amps for the Control Panel and all
Accessory Devices. For System Loading, refer to D9412GV2/D7412GV2
Operation and Installation Guide (P/N: F01U003641___).
All external connections except Terminal 5 (battery positive) are inherently power
limited. Requirements for battery standby time might reduce allowable output.
WARNING!
Multi-Battery installation requires
Model D122/D122L Dual Battery
Harness. Improper installation can
be a fire hazard.
Battery: Replace every 3 to
5 years with one or two Model
D126 12V 7Ah or D1218
12V 18Ah Lead Acid Batteries.
This equipment should be installed in accordance with the NFPA 70 (National Electrical Code)
and NFPA 72 (National Fire Alarm Code) for Local, Central Station, Remote Station, Proprietary and
Household Fire Warning Systems and under the limits of the Local Authority Having Jurisdiction
(National Fire Protection Association, Battermarch Park, Quincy, MA 02269). Printed information
describing proper installation, operation, testing, maintenance, evacuation planning and repair
service is to be provided with this equipment.
RED
Point 1 Point 2
Point 3 Point 4
Point 5 Point 6
Point 7 Point 8
DATA BUS A
GREEN
DATA BUS B
BLACK
RING
COMMON
N.F.P.A.
Style 3.5
Signaling
Line
Circuits
ZONEX OUT 1
ZONEX IN 1
ZONEX OUT 2
26
ZONEX IN 2
25
ZONEX POWER +
24
ZONEX COMMON
23
D5200/D5360
PROG CONN
Point 8
S3 Option
10
Closed = 1KΩ EOL
Normal Operation
ON when
communicating
OFF when idle
PHONE LINE SEIZED
PHONE
LED
TIP TELCO CORD
POWER +
YELLOW
D9412GV2 Control/Communicator is UL Listed For Central Station, Local, Remote Station and
Household Fire Alarm, and Central Station, Local, Police Station Connect, Household Burglar Alarm
and Encrypted Line Security when communicating via a network.
EARTH GROUND
11
PERIPHERAL DEVICE CONNECTIONS
VOLTAGE RANGES
Open
3.7 - 5.0 VDC
Normal
2.0 - 3.0 VDC
Short
0.0 - 1.3 VDC
GROUND FAULT DETECT
Enabled
Disabled
RED
Reset Pin
Disable all except Battery
Charging and Programming
System is intended to be checked by a Qualified Technician at least every 3 years.
The types of initiating circuits the panel has been approved for are A, M, W, SS.
COMMON
4
SDI Connector
Open =AB-12 UL
Bell Box 220 KΩ
11
12
13
14
15
16
17
18
19
20
21
22
GRN
MODEL D161
5
PHONE LINE
SEIZED
TIP
RING
TELCO
6
123456-
62
Charging status LED (yellow)
Low battery LED (red)
Color-coded battery leads
Ground fault detect enable
Phone LED (red)
Telephone cord connector
7
7891011-
8
9
Point 8 ground fault detect enable/disable
Operation monitor LED (green)
Accessory connector
Programming connector
Reset pin
Bosch Security Systems, Inc. | 5/05 | F01U003641B
D9412GV2/D7412GV2 | Operation and Installation Guide | 14.0
Faceplates
.
14.2
D7412GV2 Faceplate
Figure 33: D7412GV2
F01U003799B
LEDs Off When Normal
D7412GV2
YEL
Charging Status
RED
Low Battery - 12.1 VDC
1
Digital Alarm Communicator Transmitter
Refer to D9412GV2/D7412GV2 Approved Applications Compliance Guide (P/N: F01U003639___)
For System Wiring Diagram, Issue A
2
10.2 VDC - Battery Load Shed
Refer to D9412GV2/D7412GV2 Approved Applications Compliance Guide (P/N: F01U003639___)
For Compatible Smoke Detectors
CLASS 2 TRANSFORMER
16.5 VAC 40 VA 60 Hz
Model D1640
Internally Fused - Do Not short
Requires Unswitched Outlet
Do Not Share With Other Equipment
CAUTION:
+ AUX POWER
See D9412GV2/D7412GV2 Operation and Installation Guide
(P/N: F01U003641) for Power Requirements relating to Terminals 6 and 7 .
BATTERY NEGATIVE ONLY
CAUTION: Avoid damage to Panel.
WARNING!
Do not connect 24 V to terminals.
Maximum charging current 1.4 A
BATTERY POSITIVE ONLY
RELAY B
PROGRAMMABLE
ALARM OUTPUTS
Terminals
6 and 7
RELAY C
SWITCHED AUX
Terminal
8
RELAY A
3
POWER SUPPLY REQUIREMENTS
The Power Supply provides a maximum of 1.4 Amps for the Control Panel and all
Accessory Devices. For System Loading, refer to D9412GV2/D7412GV2
Operation and Installation Guide (P/N: F01U003641___).
All external connections except Terminal 5 (battery positive) are inherently power
limited. Requirements for battery standby time might reduce allowable output.
Multi-Battery installation requires
Model D122/D122L Dual Battery
Harness. Improper installation can
be a fire hazard.
Battery: Replace every 3 to
5 years with one or two Model
D126 12V 7Ah or D1218
12V 18Ah Lead Acid Batteries.
This equipment should be installed in accordance with the NFPA 70 (National Electrical Code)
and NFPA 72 (National Fire Alarm Code) for Local, Central Station, Remote Station, Proprietary and
Household Fire Warning Systems and under the limits of the Local Authority Having Jurisdiction
(National Fire Protection Association, Battermarch Park, Quincy, MA 02269). Printed information
describing proper installation, operation, testing, maintenance, evacuation planning and repair
service is to be provided with this equipment.
RED
Point 1 Point 2
Point 3 Point 4
Point 5 Point 6
Point 7 Point 8
DATA BUS A
GREEN
DATA BUS B
BLACK
RING
COMMON
N.F.P.A.
Style 3.5
Signaling
Line
Circuits
ZONEX OUT 1
ZONEX IN 1
NOT USED
26
NOT USED
25
ZONEX POWER +
24
ZONEX COMMON
23
D5200/D5360
PROG CONN
Point 8
S3 Option
Closed = 1KΩ EOL
Normal Operation
ON when
communicating
OFF when idle
PHONE LINE SEIZED
PHONE
LED
TIP TELCO CORD
POWER +
YELLOW
D7412GV2 Control/Communicator is UL Listed for Central Station, Local, Remote Station and
Household Fire Alarm, and Central Station, Local, Police Station Connect, Household Burglar Alarm
and Encrypted Line Security when communicating via a network.
EARTH GROUND
11
PERIPHERAL DEVICE CONNECTIONS
VOLTAGE RANGES
Open
3.7 - 5.0 VDC
Normal
2.0 - 3.0 VDC
Short
0.0 - 1.3 VDC
GROUND FAULT DETECT
Enabled
Disabled
RED
Reset Pin
Disable All Except Battery
Charging And Programming
System is intended to be checked by a Qualified Technician at least every 3 years.
The types of initiating circuits for which the control panel has been approved are A, M, W, SS.
COMMON
4
SDI Connector
10
Open =AB-12 UL
Bell Box 220 KΩ
11
12
13
14
15
16
17
18
19
20
21
22
GRN
MODEL D161
5
PHONE LINE
SEIZED
TIP
RING
TELCO
7
6
123456-
Charging status LED (yellow)
Low battery LED (red)
Color-coded battery leads
Ground fault detect enable
Phone LED (red)
Telephone cord connector
Bosch Security Systems, Inc. | 5/05 | F01U003641B
7891011-
8
9
Point 8 ground fault detect enable/disable
Operation monitor LED (green)
Accessory connector
Programming connector
Reset pin
63
D9412GV2/D7412GV2 | Operation and Installation Guide | Appendix A: System Wiring Diagrams, Issue A
Appendix A: System Wiring Diagrams, Issue A
A.1
D9412GV2 Control Panel
Figure 34: D9412GV2, Power Supply Side
BAT 2-
D113
CHGR-
BAT 2+
-
VAUX+
BAT 1-
SUPV
BAT 1+
CHGR+
+
D126
or
D1218
-
+
D126
or
D1218
D1640
16.5 V, 40 VA
60 Hz
Transformer
-
-
+
D126
or
D1218
+
D126
or
D1218
1
2
D8132
Battery
Charger
D126
Battery
12 V, 7 Ah
or
D1218
12 V, 17.2 Ah
or 18.0 Ah
D126
Battery
12 V, 7 Ah
or
D1218
12 V, 17.2 Ah
or 18.0 Ah
D192C/D/G
CLASS 2 TRANSFORMER
16.5 VAC 40 VA 60 Hz
Model D1640
Internally Fused - Do Not short
Requires Unswitched Outlet
Do Not Share With Other Equipment
3
+ AUX POWER
4
BATTERY NEGATIVE ONLY
5
Maximum Charging
Current 1.4 Amps.
BATTERY POSITIVE ONLY
6
RELAY A
7
RELAY B
8
RELAY C
AUX PWR
ALARM TRIG
COM
D9412GV2
PROGRAMMABLE
ALARM OUTPUTS
Terminals
7 & 8
Requires Optional
Model D136 Relay
In ALT ALARM
& SW AUX
SUPV IN
9
COMMON
ALARM CKT
10
+
-
EARTH GROUND
GROUND FAULT DETECT
Enabled
Disabled
RED
D928
PHONE
LED
Point 1 Point 2
Point 3 Point 4
TIP
RING
Point 8
S3 Option
Enabled:
Closed = 1KΩ EOL
Normal Operation
ON when
communicating
OFF when idle
PROG
CONN
Disabled:
Open =AB-12 UL
Bell Box 220 KΩ
PHONE LINE SEIZED
11
12
13
14
15
16
GRN
TELCO
C900
1 - If required by local AHJ, connect D113 Battery
Lead Supervision Module.
2 - D122 Dual Battery Harness, as required.
3 - D1640 Transformer and D8004 Transformer
Enclosure required for NFPA Applications
4 - D8132 Dual Battery Charger with two batteries
(batteries are not supervised)
5 - Power limited, supervised
6 - Power limited
7 - To Relay A or Relay B
64
891011121314-
Listed Audible Signaling Devices rated at 10.2
to 13.8 VDC (Do not use vibrating type horns.)
Optional
560 Ω, 2 Ω EOL Resistor (P/N: 15-03130-005)
RJ31X, Secondary phone line
RJ31X, Jack
RJ31X, Primary phone line
To earth ground
Bosch Security Systems, Inc. | 5/05 | F01U003641B
D9412GV2/D7412GV2 | Operation and Installation Guide | Appendix A: System Wiring Diagrams, Issue A
.
Figure 35: D9412GV2, Input Points and Peripheral Devices
1
2
3
+ AUX POWER
4
BATTERY NEGATIVE ONLY
5
Maximum Charging
Current 1.4 Amps.
BATTERY POSITIVE ONLY
6
RELAY A
7
RELAY B
8
RELAY C
9
10
D9412GV2
PROGRAMMABLE
ALARM OUTPUTS
Terminals
7 & 8
Requires Optional
Model D136 Relay
In ALT ALARM
& SW AUX
COMMON
VOLTAGE RANGES
Open
3.7 - 5.0 VDC
Normal 2.0 - 3.0 VDC
Short
0.0 - 1.3 VDC
EARTH GROUND
GROUND FAULT DETECT
Enabled
Disabled
-
+
CLASS 2 TRANSFORMER
16.5 VAC 40 VA 60 Hz
Model D1640
Internally Fused - Do Not short
Requires Unswitched Outlet
Do Not Share With Other Equipment
RED
D130
TIP
Point 1 Point 2
Point 3 Point 4
Point 5 Point 6
Point 7 Point 8
ON when
communicating
OFF when idle
PHONE LINE SEIZED
TELCO CORD
MODEL D161
Open =AB-12 UL
Bell Box 220 KΩ
11
RING
D5200/D5360
PROG CONN
Point 8
S3 Option
Closed = 1KΩ EOL
Normal Operation
PHONE
LED
12
13
14
15
16
17
18
19
20
21
22
GRN
PHONE LINE
SEIZED
RING
TIP
TELCO
P105BL
P105F
D125B
Sw. Aux Pwr
Zone B
Zone A
Pnl Common
Pnl Common
1
2
D129
3
4
Loop B-
5
6
Loop A-
7
Loop B+
Loop BLoop BLoop B+
8
9
Earth Ground 10
Loop A+
3
4
Aux Power
5
6
Earth Ground
7
Zone B
Loop B+
1
2
Common
8
Zone A 9
Loop A+ 10
Loop A-
11
12
Loop A+ 13
Loop A-
1 - (Optional): For 24 V applications use a UL Listed
24 VDC power supply with a D130 Relay Module.
Refer to the D130 Installation Instructions
(P/N: 74-06262-00) for correct wiring
requirements.
2 - To UL Listed two-wire smoke detectors. Refer to
the 9000/G/GV2 Series Technical Service Note:
UL Smoke Detector Compatibility (P/N: 33284) for
a listing of compatible two-wire smoke detectors.
3 - P105 1 kΩ EOLR (P/N: 14-03130-004): Suitable
for non-powered initiating and supervisory devices
such as pull stations, heat sensors, and valve
tampers.
P105BL1 1kΩ EOLR (P/N: 14-0130-004): For
typical burglar alarm applications.
5 - D129 provides optional Waterflow Retard
feature. Not suitable for two-wire smoke
detectors. (Note: Use Zero Retard except for
waterflow devices.)
4-
All external connections except Terminal 5 (battery positive) are power limited.
Bosch Security Systems, Inc. | 5/05 | F01U003641B
65
D9412GV2/D7412GV2 | Operation and Installation Guide | Appendix A: System Wiring Diagrams, Issue A
Figure 36: D9412GV2, SDI Devices
D1255
D1256
D1257
D1260
PERIPHERAL DEVICE CONNECTIONS
RED
POWER +
32
YELLOW
DATA BUS A
31
GREEN
DATA BUS B
30
COMMON
29
ZONEX OUT 1
28
ZONEX IN 1
27
ZONEX OUT 2
26
ZONEX IN 2
25
ZONEX POWER +
24
ZONEX COMMON
23
BLACK
N.F.P.A.
Style 3.5
Signaling
Line
Circuits
D9210B
D9131A
D5200/D5360
PROG CONN
Point 8
S3 Option
Closed = 1KΩ EOL
Normal Operation
D9133TTL-E
Open =AB-12 UL
Bell Box 220 KΩ
GRN
D8128D
D8125
+
-
D8125
+
D8128D
D8129
D8129
1234567-
Up to 8 supervised keypads
Up to 8 D9210Bs
Up to 3 supervised 9131As
Power limited, supervised
Power limited
POPEX 1
POPEX 2
8910 11 12 -
Up to 119 D9127U/T POPITs or up to
63 D8127U/T POPITs
Zonex 1: 15 D8128Ds
Zonex 2: 15 D8128s
Zonex 1: Up to 8 maximum
Zonex 2: Up to 8 maximum
All external connections except Terminal 5 (battery position) are power limited.
66
Bosch Security Systems, Inc. | 5/05 | F01U003641B
D9412GV2/D7412GV2 | Operation and Installation Guide | Appendix A: System Wiring Diagrams, Issue A
.
A.2
D7412GV2 Control Panel
Figure 37: D7412GV2, Power Supply Side
D113
BAT 2-
CHGR-
BAT 2+
VAUX+
BAT 1-
SUPV
BAT 1+
CHGR+
D126/
D1218
D126/
D1218
D1640
16.5 V, 40 VA
60 Hz
D126/
D1218
D126/
D1218
CLASS 2 TRANSFORMER
16.5 VAC 40 VA 60 Hz
Model D1640
Internally Fused - Do Not short
Requires Unswitched Outlet
Do Not Share With Other Equipment
D7412GV2
+ AUX POWER
D8132
BATTERY NEGATIVE ONLY
Maximum Charging
Current 1.4 Amps.
BATTERY POSITIVE ONLY
D126
Battery
12 V, 7 Ah/
D1218
12 V, 17.2 Ah
or 18.0 Ah
D192C/G
D126
Battery
12 V, 7 Ah/
D1218
12 V, 17.2 Ah
or 18.0 Ah
PROGRAMMABLE
ALARM OUTPUTS
Terminals
7 & 8
RELAY A
AUX PWR
RELAY B
Requires Optional
Model D136 Relay
In ALT ALARM
& SW AUX
ALARM TRIG
RELAY C
COM
SUPV IN
COMMON
ALARM CKT
EARTH GROUND
+
-
GROUND FAULT DETECT
Enabled
Disabled
RED
D928
Point 1 Point 2
Point 3 Point 4
ON when
communicating
OFF when idle
PHONE LINE SEIZED
PHONE
LED
RING
TIP
TELCO
11
12
13
14
15
16
C900
1 - If required by local AHJ, connect D113 Battery
Lead Supervision Module.
2 - D122 Dual Battery Harness, as required.
3 - D1640 Transformer and D8004 Transformer
Enclosure required for NFPA Applications
4 - D8132 Dual Battery Charger with two batteries
(batteries are not supervised)
5 - Power limited, supervised
6 - Power limited
7 - To Relay A or Relay B
Bosch Security Systems, Inc. | 5/05 | F01U003641B
891011121314-
Listed Audible Signaling Devices rated at 10.2
to 13.8 VDC (Do not use vibrating type horns.)
Optional
560 Ω, 2 Ω EOL Resistor (P/N: 15-03130-005)
RJ31X, Secondary phone line
RJ31X, Jack
RJ31X, Primary phone line
To earth ground
67
D9412GV2/D7412GV2 | Operation and Installation Guide | Appendix A: System Wiring Diagrams, Issue A
Figure 38: D7412GV2, Input Points and Peripheral Devices
CLASS 2 TRANSFORMER
16.5 VAC 40 VA 60 Hz
Model D1640
Internally Fused - Do Not short
Requires Unswitched Outlet
Do Not Share With Other Equipment
D7412GV2
+ AUX POWER
BATTERY NEGATIVE ONLY
Maximum Charging
Current 1.4 Amps.
BATTERY POSITIVE ONLY
PROGRAMMABLE
ALARM OUTPUTS
Terminals
7 & 8
RELAY A
RELAY B
Requires Optional
Model D136 Relay
In ALT ALARM
& SW AUX
RELAY C
COMMON
VOLTAGE RANGES
Open
3.7 - 5.0 VDC
Normal 2.0 - 3.0 VDC
Short
0.0 - 1.3 VDC
EARTH GROUND
GROUND FAULT DETECT
Enabled
Disabled
-
+
RED
PHONE
LED
Point 1 Point 2
Point 3 Point 4
Point 5 Point 6
Point 7 Point 8
ON when
communicating
OFF when idle
PHONE LINE SEIZED
D130
TIP
TELCO CORD
MODEL D161
RING
11
12
13
14
15
16
17
18
19
20
21
22
PHONE LINE
SEIZED
TIP
RING
TELCO
P105BL
P105F
D125B
Sw. Aux Pwr
Zone B
Zone A
Pnl Common
Pnl Common
1
2
3
4
Loop B-
5
6
Loop A-
7
Loop B+
Loop A+
8
9
Earth Ground 10
D129
Loop B+
Loop BLoop BLoop B+
Zone B
Aux Power
1
2
3
4
5
6
Earth Ground
7
Common
8
9
Zone A
Loop A+ 10
Loop A- 11
Loop A- 12
Loop A+ 13
1 - (Optional): For 24 V applications, use a UL Listed
24 VDC power supply with a D130 Relay Module.
Refer to the D130 Installation Instructions
(P/N: 74-06262-000) for correct wiring
requirements.
2 - To UL Listed two-wire smoke detectors. Refer to
the 9000/G/GV2 Series Technical Service Note:
UL Smoke Detector Compatibility (P/N: 33284) for
a listing of compatible two-wire smoke detectors.
3 - P105 1 kΩ EOLR (P/N: 14-03130-004):
Suitable for non-powered initiating and
supervisory devices such as pull stations, heat
sensors, and valve tampers.
4- P105BL1 1kΩ EOLR (P/N: 14-0130-004): For
typical burglar alarm applications.
5 - D129 provides optional Waterflow Retard
feature. Not suitable for two-wire smoke
detectors. (Note: Use Zero Retard except for
waterflow devices.)
All external connections except Terminal 5 (battery positive) are power limited.
68
Bosch Security Systems, Inc. | 5/05 | F01U003641B
D9412GV2/D7412GV2 | Operation and Installation Guide | Appendix A: System Wiring Diagrams, Issue A
.
Figure 39: D7412GV2, SDI Devices
D1255
D1256
D1257
D1260
D7412GV2
CLASS 2 TRANSFORMER
16.5 VAC 40 VA 60 Hz
Model D1640
Internally Fused - Do Not short
Requires Unswitched Outlet
Do Not Share With Other Equipment
+ AUX POWER
BATTERY NEGATIVE ONLY
Maximum Charging
Current 1.4 Amps.
BATTERY POSITIVE ONLY
RELAY A
PROGRAMMABLE
ALARM OUTPUTS
Terminals
7 & 8
PERIPHERAL DEVICE CONNECTIONS
PERIPHERAL DEVICE CONNECTIONS
RED
POWER +
RED
POWER +
YELLOW
YELLOW
DATA BUS A
DATA BUS A
GREEN
GREEN
DATA BUS B
DATA BUS B
BLACK
BLACK
COMMON
COMMON
NFPA
NFPA
Style
3.5
Style 3.5
Signaling
Signaling
Line
Line
Circuits
Circuits
D9210B
ZONEX OUT 1
ZONEX OUT 1
NOT USED
26
NOT USED
25
COMMON
ZONEX POWER +
24
EARTH GROUND
ZONEX COMMON
23
RELAY B
RELAY C
Requires Optional
Model D136 Relay
In ALT ALARM
& SW AUX
GROUND FAULT DETECT
Enabled
Disabled
RED
RING
TELCO
D5200/D5360
PROG CONN
Point 8
S3 Option
ON when
PHONE communicating
LED
OFF when idle
PHONE LINE SEIZED
TIP
D9131A
ZONEX IN 1
ZONEX IN 1
D9133TTL-E
or
DX4020
Closed = 1KΩ EOL
Normal Operation
Open =AB-12 UL
Bell Box 220 KΩ
GRN
D8128D
D8125
+
1234-
-
Up to 8 supervised
Up to 3 supervised
Power limited, supervised
POPEX 1
D8129
5 - Up to 119 D9127U/T POPITs or up to 63
D8127U/T POPITs
6 - Zonex 1: 15 D8128Ds
7- Zonex 1: Up to 8 maximum
All external connections except Terminal 5 (battery positive) are power limited.
Bosch Security Systems, Inc. | 5/05 | F01U003641B
69
D9412GV2/D7412GV2 | Operation and Installation Guide | Appendix B: Point Address Charts
Appendix B: Point Address Charts
B.1
Zonex 1, Points 9 to 127 (D9412GV2);
Zonex 1, Points 9 to 75 (D7412GV2)
Place the labels on the base of the POPIT. Do not attach labels to the POPIT cover.
A bullet (•) in the switch column indicates that the switch is set to ON.
D8127 or D9127 POPITs can be used for Points 9 to 72; however, only D9127 POPITs can be used for Points 73
to 127.
D8127 POPITs have DIP switches 1 to 6; D9127 POPITs have DIP switches 0 to 6.
Table 25:
Zonex 1 Point Address Chart
2
1
Address
Switch
0
1
2
2
3
4
5
6
1
Address
Switch
0
1
009
049
•
•
•
•
•
•
•
•
010
050
•
•
•
•
•
•
•
011
051
•
•
•
•
•
•
•
012
052
•
•
•
•
•
•
013
053
•
•
•
•
•
•
•
014
054
•
•
•
•
•
•
015
055
•
•
•
•
•
•
016
056
•
•
•
•
•
017
057
•
•
•
•
•
•
•
018
058
•
•
•
•
•
•
019
059
•
•
•
•
•
•
020
060
•
•
•
•
•
021
061
•
•
•
•
•
•
022
062
•
•
•
•
•
023
063
•
•
•
•
•
024
064
•
•
•
•
025
065
•
•
•
•
•
•
•
026
066
•
•
•
•
•
•
027
067
•
•
•
•
•
•
028
068
•
•
•
•
•
029
069
•
•
•
•
•
•
030
070
•
•
•
•
•
031
071
•
•
•
•
•
032
072
•
•
•
•
033
073
•
•
•
•
•
•
034
074
•
•
•
•
•
035
075
•
•
•
•
•
036
076
•
•
•
•
037
077
•
•
•
•
•
038
078
•
•
•
•
039
079
•
•
•
•
040
080
•
•
•
041
081
•
•
•
•
•
•
•
042
082
•
•
•
•
•
•
043
083
•
•
•
•
•
•
044
084
•
•
•
•
•
045
085
•
•
•
•
•
•
046
086
•
•
•
•
•
047
087
•
•
•
•
•
048
088
•
•
•
•
1 - Points 9 to127 (D9412GV2); Points 9 to 75 (D7412GV2).
2 - A dot (·) in the Switch column indicates the switch is set to ON.
3 - The control panel reserves Point 128 for internal use.
70
2
2
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
3
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1
4
5
5
Address
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
089
090
091
092
093
094
095
096
097
098
099
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
3
128
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Switch
0
1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
2
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
3
4
5
6
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
6
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Bosch Security Systems, Inc. | 5/05 | F01U003641B
D9412GV2/D7412GV2 | Operation and Installation Guide | Appendix B: Point Address Charts
.
B.2
Zonex 2, Points 129 to 247 (D9412GV2 Only)
Place the labels on the base of the POPIT. Do not attach labels to the POPIT cover.
A number in the switch column indicates that the switch is set to ON.
Table 26:
Zonex 2 Point Address Chart
2
1
Address
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
Switch
0
1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
2
2
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
3
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
4
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
5
•
•
6
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1
Address
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
Switch
0
1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
2
2
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
3
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
4
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
5
•
•
5
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1
Address
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
3
248
Switch
0
1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
2
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
3
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
4
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
5
•
•
6
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1 - Points 129 to 247 (D9412GV2 only).
2 - A dot (·) in the Switch column indicates the switch is set to ON.
3 - The control panel reserves Point 248 for internal use.
Bosch Security Systems, Inc. | 5/05 | F01U003641B
71
D9412GV2/D7412GV2 | Operation and Installation Guide | Specifications
Specifications
Table 27:
Specifications
Voltage Input
(Power Supply)
Primary:
Secondary:
Current
Requirements
Power
Outputs*
All external connections are power-limited except battery terminals.
Continuous
Power Outputs
Switched Aux
Power
Fire and
Fire/Burglary
Systems
Telephone
Connections
Battery
Discharge/
Recharge
Schedule
16.5 VAC 40 VA class 2 plug-in transformer (D1640)
Sealed lead-acid rechargeable battery (12 VDC, 7 Ah or 12 VDC, 17.2 or 18 Ah).
The control panel supports up to two 12 VDC, 7 Ah batteries using the D122 Dual
Battery Harness or two D1218 (12 VDC, 17.2 or 18 Ah) batteries using a D122.
Control Panel: Idle 200mA; Alarm 500 mA
Refer to the Current Rating Chart for Standby Battery Calculations section in the D9412GV2/D7412GV2 Approved
Applications Compliance Guide (P/N: F01U003639) for the current draw requirements of other system components.
Alarm Power
Output
Minimum
Operating
Voltage
SDI Bus
Terminals 1
and 2
Terminals 4
and 5
Terminals 3,
24, and 32
1.4 A maximum at 10.2 VDC to 13.9 VDC (continuous supply) total for all devices
and outputs supplied at Terminals 3, 24, and 32 and at the accessory and
programming connectors.
Terminals 6
2.0 A maximum at 10.2 VDC to 13.9 VDC output. Output can be steady or one of
and 7
three pulsed patterns depending on programming. Refer to Relays in the
D9412GV2/D7412GV2 Program Entry Guide (P/N: F01U003636).
Terminal 8
1.4 A maximum at 10.2 VDC to 13.9 VDC output. Continuous output is interrupted
by Sensor Reset or alarm verification depending on programming. Refer to Relays in
the D9412GV2/D7412GV2 Program Entry Guide (P/N: F01U003636).
To comply with UL 985 and 864 listing standards for fire alarm systems (effective March 1, 1989), the
total combined continuous and alarm current draw for the system during alarm conditions must be
limited to 1.4 A provided by the primary power supply (rectified AC). If current draw for the system
exceeds 1.4 A, remove connected devices until the current draw falls below 1.4 A. Then, connect the
removed devices to a D8132 Battery Charger Module or to an external power supply (refer to
Figure 25 on page 55).
10.2 VDC
SDI Bus A (+):
SDI Bus B (-):
Connection:
Two telco
line
s:
Discharge
Cycle
Recharge
Cycle
9 VDC 4572 m (15000 ft) maximum
9 VDC 4572 m (15000 ft) maximum
RJ31X or RJ38X jack can connect the control panels.
Bosch Security Systems D928 Dual Phone Line Module required for two phone line service.
Supervision supplied by the control panel.
13.9 VDC
13.8 VDC
12.1 VDC
10.2 VDC
10.0 VDC
AC ON
Charging float level.
Charging status LED on.
Low Battery and AC Fail Reports if programmed. Low Battery LED on.
Minimum operational voltage
Battery load shed (processing functions continue if AC is present).
Load shed relay resets, battery charging begins, Battery Trouble and AC Restoral
Reports sent.
13.7 VDC
Battery Restoral Report sent, Low Battery LED off.
13.9 VDC
Charging status LED off, battery float charged.
0°C to +50°C (+32°F to +122°F)
Environmental
Temperature:
Arming
Stations
Point
Thresholds
Relative
Maximum 95% non-condensing
Humidity:
D720 Command Center, D1255 Command Center, D1256 Fire Command Center; D1257 Fire Alarm Annunciator;
D1260 Alpha V Command Center; Keyswitch
Greater than 3.7 VDC, but less than 5.0 VDC.
On-board Points Open
Normal
Greater than 2.0 VDC, but less than 3.0 VDC.
1 to 8
Short
Greater than 0.0 VDC, but less than 1.3 VDC.
D8103 Universal Enclosure, D8109 Fire Enclosure, D8108A Attack Resistant Enclosure, BATB-40 Battery Box
Compatible
Enclosures
72
Bosch Security Systems, Inc. | 5/05 | F01U003641B
D9412GV2/D7412GV2 | Operation and Installation Guide | Specifications
.
Notes
Bosch Security Systems, Inc. | 5/05 | F01U003641B
73
Bosch Security Systems, Inc.
130 Perinton Parkway
Fairport, NY 14450-9199
Customer Service: (800) 289-0096
Technical Support: (888) 886-6189
© 2005 Bosch Security Systems
F01U003641B
Download PDF

advertising