Fire Alarm Systems | D9124 Addressable Fire Alarm Control Panel (FACP)
D9124 Addressable Fire Alarm Control
Panel (FACP)
▶ 24 VDC, 4 A power for initiation circuits and NACs;
12 VDC, 1.4 A power for system accessories
▶ Up to eight supervised or 32 unsupervised remote
annunciators
▶ One-man Fire Test Mode
▶ Schedules (Skeds function) service reminder for local
systems
▶ Low battery, AC power supply, and battery lead
supervision
▶ Dual phone line monitor
The D9124 FACP controls complex alarm systems used in
schools, universities, manufacturing plants, and health care
facilities. Program it for fire, fire supervisory, intrusion, or
access control applications. Program it locally using the
D5200CE hand-held programmer or remotely using RPS
over telephone lines or local-area or wide-area networks
(LAN or WAN).
The D9124 FACP is a modular assembly, installed in a red
steel enclosure, which can be surface- or flush-mounted.
The enclosure has keyed controller access making it
suitable for installation in public access areas.
Functions
Alarm Verification
The alarm verification feature reduces potential false alarms
by requiring a reset and a second alarm signal from the
device before the control panel raises an alarm condition.
Auxiliary and Standby Power
The 4 A, 24 VDC power supply charges the standby batteries
and powers auxiliary devices. The power supply responds
to low battery or battery disconnect conditions with a
Trouble LED and a Trouble Relay for sounders or lights.
Five system power trouble conditions are selected by DIP
switches. They can be individually linked to a central
station, or grouped to activate a trouble relay, allowing a
single supervised address to monitor the power supply.
A pair of 12 V batteries provides standby power. Two
additional batteries provide standby power for initiating
devices and notification appliances. All four batteries are
housed within the panel enclosure.
Note
Batteries are not included in the D9124 and
must be purchased separately.
Central Station Communication
Events can be communicated to a central station by the
digital communicator or by adding an optional Ethernet
interface module. The optional Bosch D6500 or D6600
NetCom Receiver and Modem IIIa2 reporting format provide
individual point reporting to monitoring facilities.
The D5500 Remote Programming Software (RPS) allows
the following to be controlled from a central station:
•
•
•
•
•
•
•
Resetting notification appliances
Activating or deactivating remote annunciation
Activating or deactivating relays
Supervising battery condition
Setting point status and armed status
Enabling or disabling reporting functions
Shunting reporting points during servicing
www.boschsecurity.com
2 | D9124 Addressable Fire Alarm Control Panel (FACP)
Event Log Storage, Viewing, and Printing
The D9124's memory log stores time, date, point, and user
ID for up to 1000 events. Programming options allow
restricting specific event reports to the central station
receiver. A programming option allows the log to record
certain functions entered at command centers.
Certifications and Approvals
Region
Certification
USA
UL
AMCX: Central Station Alarm Units
(UL1610, UL1635), APAW: Police Station
Alarm Units (UL365, UL464), UOJZ:
Control Units, System (UL864)
Display the 1000 events in memory at the fire system
controller(s) or retrieve them with a single phone call by a
central station using Bosch RPS version 3.7.025 or higher.
FM
The D9131A Parallel Printer Interface Module allows an onsite parallel printer to print events as they are stored in the
log: recording time, date, account number, event, point ID,
point text, and if the message was transmitted to a receiver.
CSFM
7165-1615: 113 and 7170-1615:
144 July 2008
NYC-MEA
12-92-E, Vol. IV 12-92-E, Vol. IV
Inputs
The D9124 Control Panel is a 127-point addressable system
that is expandable to 246 addressable points. The control
panel receives information from alarm initiating points
through integrated devices over a two-wire multiplex zone
expansion system. Each addressable point accommodates
both normally-open and normally-closed devices with endof-line (EOL) resistor supervision. Each point is
programmable for fire, fire supervisory, intrusion, or access
control applications.
Outputs
System notification appliance capacity can be extended
beyond the two supervised circuits by adding D8129 Octorelay Modules. Up to 128 relay outputs can be operated
through the controller or the central station, or they can be
programmed for automatic operations.
Notification appliances can be programmed for steady,
pulsed, California March Time, or Temporal Code 3
patterns. Temporal Code 3 patterns can be synchronized
using the appropriate synchronization modules.
12-92-E, Vol. X11 12-92-E, Vol. 12
Hong Kong
HKFSD
Installation/Configuration Notes
Compatible Products
The following products are compatible with the D9124
FACP:
Category
Product ID
Product Description
Batteries and
Power Supply
Products
BATB-40
Battery box
BATB-80
Battery box
D126
12 V, 7 Ah standby battery
D1218
12 V, 18 Ah standby battery
D7038
Power supply address circuit module
D285
Photoelectric smoke head
D285TH
Photoelectric smoke head with heat
D298M
Zonex smoke master base
Detectors
D298S
Zonex smoke single base
Notification Appliance Circuits (NACs)
FMM-462
Manual station
The D9124 FACP has two supervised, on-board NACs with
individual circuit silencing.
D603
Rate-of-rise heat detector head
D604
Fixed (135°F) heat detector head
User Interface
D605
Fixed (190°F) heat detector head
D720B/R
Security and fire keypads
D1255B/R
Security and fire keypads
D1256
Fire command center
D1257
Remote fire alarm annunciator
D1260
ATM keypad
D125B
Powered loop interface module
(Dual, Class B)
D129
Initiation circuit module
(Dual, Class A)
D130
Relay module
D136
Plug-in relay
D192C
Bell supervision module
D192E
Bell supervision module
A D1256 Fire Alarm keypad is visible and accessible behind
a locked, clear sliding panel located on the enclosure door.
It displays programmable text identifying specific initiating
and supervisory devices. It also provides point
annunciation, signal silence, trouble silence, detector reset,
and annunciator reset. The sliding panel lock is keyed to
match the Bosch manual pull stations for resetting the
system.
Also available as options are:
•
•
•
D1255R Security/Fire Keypad
D1257 Remote Fire Alarm Annunciator
D1260 Keypad
Keypads and
Annunciators
Modules
D9124 Addressable Fire Alarm Control Panel (FACP) | 3
Category
Programming
Products
Product ID
Product Description
Technical Specifications
D192G
Bell supervision module
D8125
POPEX module
Environmental Considerations
D8125MUX
Zonex to dual multiplex interface
D8128D
OctoPOPIT module
D8129
Octo-relay module
Inputs
D8130
Release module
D9127U
POPIT module (no tamper)
Sensor Circuits:
Up to two 8125 POPEX modules,
119 addresses per module
D9127T
POPIT module (tamper)
Sensor Circuit Protection:
D9131A
Parallel printer interface module
DX4020
Ethernet interface module
Power limited to 4 A; short circuit, reverse
polarity, thermal overload and current overload protection on-board
D5200CE
Handheld programmer
Sensor Loop Technology:
Four-wire addressable circuits
RPS
Remote Programming Software
RPS-LITE
Remote Programming Software
RPS-INTL
Remote Programming Software
Relative Humidity:
Up to 85%; non-condensing
Temperature (operating):
+32°F to +122°F (0°C to +50°C)
Mechanical Properties
Parts Included
The D9124 Addressable Control Panel is shipped in three
boxes. One box contains:
Quant.
Component
1
D9412GLTB Control Panel (less terminal blocks)
Another box contains:
Quant.
Component
1
D9101 Enclosure Assembly with Door
The third box contains a D9100 Accessory Module Carrier
that includes the following:
Quant.
Component
2
D192C Indicating Circuit Supervision Modules
1
D928 Dual Phone Line Switcher
1
D8125 POPEX Module (additional optional)
1
D9142LC 24 VDC Power Supply
The third box also contains:
Quant.
Component
1
D1256 Fire Alarm Keypad
1
D1601 Transformer
1
Wiring Harness
1
Wiring Harness for the D8125 POPEX Module
2
560 Ω Resistors (for D192C Modules)
2
D161 Dual Modular Telephone Cords
1
D162 Dual Modular Telephone Cord
1
Literature pack
Color:
Red
Material:
16-gauge (1.5 mm) steel
Dimensions (H x W x D)
Enclosure Box:
36.1 in. x 22.1 in. x 3.2 in.
(92 cm x 56 cm x 8.1 cm)
Removable Door:
37.1 in. x 23.3 in. x 1.1 in.
(94 cm x 59 cm x 2.8 cm)
Outputs
Off-board relays:
Up to 16 optional D8129 Relay Modules (eight relay outputs per module)
On-board NACs:
Two; 1.8 A maximum per circuit
Power Requirements
Current (operating)
Alarm + sensor load:
874 mA
Idle:
412 mA
Power (auxiliary):
24 VDC nominal at 1.8 A
Power (primary):
120 VAC, 60 Hz, 360 VA
Ordering Information
D9124 Addressable Fire Alarm Control
Panel (FACP)
Up to eight supervised or 32 unsupervised remote annunciators
D9124
Accessories
D113 Battery Lead Supervision Module
Supervises wiring connections for two 12 V
batteries connected to the same set of charging
terminals.
D113
D122 Dual Battery Harness
Harness with circuit breaker. Connects two
batteries to a compatible control panel.
D122
D135A Low‑battery Disconnect Module
Disconnects the control panel from the battery
when the battery level drops to 9.5 VDC.
D135A
www.boschsecurity.com
4 | D9124 Addressable Fire Alarm Control Panel (FACP)
Ordering Information
D127 Reversing Relay Module
Reports two separate alarm conditions to the
central station.
D127
D136 Plug‑In Relay
Maximum rating is 1 A at 24 VDC or 2 A at
12 VDC. Available individually (D136) or in a
package of 25 (D136‑25).
D136
D138 Mounting Bracket, Right Angle
Used to mount accessory modules in D8103,
D8108A, and D8109 enclosures.
D138
Americas:
Bosch Security Systems, Inc.
130 Perinton Parkway
Fairport, New York, 14450, USA
Phone: +1 800 289 0096
Fax: +1 585 223 9180
security.sales@us.bosch.com
www.boschsecurity.us
Europe, Middle East, Africa:
Bosch Security Systems B.V.
P.O. Box 80002
5600 JB Eindhoven, The Netherlands
Phone: + 31 40 2577 284
Fax: +31 40 2577 330
emea.securitysystems@bosch.com
www.boschsecurity.com
© Bosch Security Systems Inc. 2010 | Data subject to change without notice
T1113332363 | Cur: en-US, V5, 4 Jul 2010
Asia-Pacific:
Represented by
Robert Bosch (SEA) Pte Ltd, Security Systems
11 Bishan Street 21
Singapore 573943
Phone: +65 6258 5511
Fax: +65 6571 2698
apr.securitysystems@bosch.com
www.boschsecurity.com
Download PDF

advertising