Bosch | F220-B6 | User's Manual | Bosch F220-B6 User's Manual

4998138694Er7.book Page 1 Thursday, March 1, 2007 8:42 AM
F220 Series Detectors with
F220-B6/C/E/R Bases
Installation Manual
en
English manual
4998138694Er7.book Page 2 Thursday, March 1, 2007 8:42 AM
2
en | Legal
F220 Series Detectors with F220-B6/C/E/R Bases
1
Legal
1.1
Trademarks
CleanMe® is a registered trademark of GE Interlogix in the
United States and/or other countries.
Chamber Check® is a registered trademark of Bosch Security
Systems, Inc. in the United States.
Chambermaid™ is a trademark of Bosch Security Systems, Inc.
in the United States.
ENVI-RO-TECH™ is a trademark of Tech Spray L.P.
TECHSPRAY® is a registered trademark of Tech Spray L.P.
1.2
Required Maintenance and Testing
Keep the detector calibrated for proper operation. NFPA 72,
The National Fire Alarm Code, recommends performing
calibration tests at installation, then every other year.
Depending on local regulations, calibration testing might be
required more than once a year.
Perform functional testing yearly.
i
NOTE! Notify all concerned parties before any
maintenance or testing of the fire alarm system and upon
completion of these activities.
Test the calibration (to meet NFPA 72) using either the magnet
test or measuring the calibration with a calibrated product from
No Climb Products Ltd. Quickly determine the calibration by a
visual inspection of the detector’s LED (refer to Section 4.4
Flash Rate and Trouble Indication on page 22). These tests
confirm whether or not the detector is within its factory marked
calibration range.
At least once a year vacuum or wipe the external part of the
detector clean. Pay particular attention to the detector screens
in areas of heavy insect activity or dust. To clean the chamber,
4998138694 -04 | 2007.01
Installation Manual
Bosch Security Systems, Inc.
4998138694Er7.book Page 3 Thursday, March 1, 2007 8:42 AM
F220 Series Detectors with F220-B6/C/E/R Bases
General Information | en
3
use a can of clean, dry compressed air (such as TECHSPRAY
ENVI-RO-TECH Duster) which is available at office and alarm
supply stores. Shorten the plastic tube that comes with the
compressed air to about 2 in. (5 cm). Place the tube or needle
valve through the Chambermaid valve in the bottom of the
detector (refer to Figure 2.2 on page 7).
i
2
NOTE! Do not paint the detectors. Paint or other foreign
matter covering the detector can prevent smoke
detection.
General Information
This document covers mounting, wiring, power requirements,
testing, and maintenance for the F220-B6, F220-B6C, F220-B6E,
and F220-B6R Detector Bases and the F220 Series Heat and
Photoelectric Smoke Detectors. Install them according to
NFPA 72.
i
NOTE! For proper system installation, read and
understand NFPA-72 before installation.
For installation guidelines, refer to Installation Considerations
for Smoke and Fire Detectors (P/N: 26715).
2.1
F220-B6 Series Detector Bases
2.1.1
Compatible Control Panels
Two-wire:
NOTE! Bosch Security Systems, Inc. makes no claim
i
written, oral, or implied that the F220 Series Detectors
work with any two-wire control panels except those
specified in the Base Compatibility chart in Technical
Service Note (P/N: 4998148185).
Bosch Security Systems, Inc.
Installation Manual
4998138694 -04 | 2007.01
4998138694Er7.book Page 4 Thursday, March 1, 2007 8:42 AM
4
en | General Information
F220 Series Detectors with F220-B6/C/E/R Bases
Four-wire: Compatible with all UL Listed four-wire control
panels. Refer to the control panel manufacturer’s installation
instructions for proper end-of-line (EOL) resistor selection.
2.1.2
Base Comparisons
The F220-B6 is a two-wire base, while the F220-B6C, F220-B6E,
and F220-B6R are four-wire bases. All three of the four-wire
bases have a Form A alarm relay. In addition to the alarm relay,
the:
–
F220-B6C has a Form C auxiliary alarm relay
–
F220-B6E has a power supervision (EOL) relay
NOTE! Use the F220-B6RS when a built-in sounder is
needed. The F220-B6RS also has a Form A alarm relay.
Refer to the F220 Series Detectors with the F220-B6RS
i
Installation Manual (P/N: F01U029847).
For addressable systems, use the F220-B6PM
Addressable POPIT Master Base or F220-B6PS
Addressable POPIT Base. Refer to the F220-B6PS/M
Installation Manual (P/N: 4998149982).
4998138694 -04 | 2007.01
Installation Manual
Bosch Security Systems, Inc.
4998138694Er7.book Page 5 Thursday, March 1, 2007 8:42 AM
F220 Series Detectors with F220-B6/C/E/R Bases
2.1.3
General Information | en
5
Base Features
12
11
10
9
11
13
7
12
8
6
12
3
4
2
5
1
11
11
12
1.
Terminal 1
8.
Remote Terminal (c)
2.
Terminal 2
9.
Tamper Tab (Locking Bar)
3.
Terminal 3
10. Tamper Tab (Locking Bar
4.
Terminal 4
5.
Terminal 5
6.
Mount)
11. Alignment Key (4 places)
Resettable Auxiliary Power 12. Snap Lock (4 places)
Positive (+) In and Out
13. Earth Shield Terminal
Terminals (b1 and b2)
7.
(optional)
Resettable Auxiliary Power
Negative (-) In and Out
Terminal (a1/a2)
Fig. 2.1
Base Features
Bosch Security Systems, Inc.
Installation Manual
4998138694 -04 | 2007.01
4998138694Er7.book Page 6 Thursday, March 1, 2007 8:42 AM
6
en | General Information
2.2
F220 Series Detectors with F220-B6/C/E/R Bases
F220 Series Detectors
2.2.1
About F220 Series Detector Heads
The F220 Series Detector Heads listed inTable 2.1 each require
an F220-B6 Series Base.
!
WARNING! The F220-PTHC detects carbon monoxide
(CO) as a component of a fire. Do not use the F220-PTHC
as a stand-alone CO detector.
Electronic heat detector 135°F (57°C), fixed
F220-135
F220-135F
F220-190F
F220-P
F220-PTH
temperature and rate-of-rise
Electronic heat detector 135°F (57°C), fixed
temperature only
Electronic heat detector 190°F (88°C), fixed
temperature only
Photoelectric smoke detector
Photoelectric smoke detector with integral 135°F
(57°C) heat sensor
Photoelectric smoke detector with integral 135°F
F220-PTHC (57°C) heat sensor and CO enhanced smoke
detection
Table 2.1
4998138694 -04 | 2007.01
F220 Series Detector Heads
Installation Manual
Bosch Security Systems, Inc.
4998138694Er7.book Page 7 Thursday, March 1, 2007 8:42 AM
F220 Series Detectors with F220-B6/C/E/R Bases
2.2.2
General Information | en
7
F220 Series Detector Features
1
5
2
6
4
3
1.
Front of detector
2.
Light-emitting diode (LED) 5.
Back of detector
Thermistor
Chambermaid location
3.
4.
6.
Unlocking port
(heat detectors only)
Fig. 2.2
2.2.3
Detector Features
F220 Series Heat Detector Heads
The F220 Heat Detector Heads can be identified by color coding
(refer to Table 2.2).
F220-135
No circle around the thermistor
F220-135F A gray circle around the thermistor
F220-190F A black circle around the thermistor
Table 2.2 Distinguishing Heat Detectors
!
WARNING! The F220-135, F220-135F and F220-190F are
not life safety devices. Use them with F220-B6 Series
bases to provide general property protection.
Bosch Security Systems, Inc.
Installation Manual
4998138694 -04 | 2007.01
4998138694Er7.book Page 8 Thursday, March 1, 2007 8:42 AM
8
en | General Information
2.2.4
F220 Series Detectors with F220-B6/C/E/R Bases
F220 Series Smoke Detector Heads
The F220 Series Smoke Detector Heads are UL Listed, openarea photoelectric smoke detectors that work with commercial
fire protective signaling systems and household fire warning
systems. Select the appropriate mounting base to configure the
detectors for two-wire or four-wire versions (refer to
Section 2.1.2 Base Comparisons on page 4).
To verify power to the detector and a functioning smoke
sampling circuitry, a dual color LED indicator flashes green
every eight seconds when operating normally. It flashes once
every four seconds when a trouble condition exists. If the
detector determines an alarm condition exists, the LED
changes from flashing green to steady red. The detector returns
to normal when power is interrupted and the alarm condition
clears.
Throughout its normal life cycle, the smoke detector monitors
and periodically adjusts itself to keep the sensitivity at its
factory calibrated level. When excessively dirty, the detector’s
LED flash rate changes from an eight second flash rate to a four
second rate. If CleanMe is selected, the detector sends a
CleanMe signal to the compatible control panel to indicate a
dirty smoke detector.
Refer to Section 4.3 Set CleanMe Feature on page 22.
2.3
Technical Specifications
2.3.1
General Specifications
Air Velocity
Operating
4000 ft/min (1200 m/min) maximum
+32°F to 100°F (0°C to 38°C)
Temperature
Relative
0% to 95% (non-condensing)
Humidity
Table 2.3
4998138694 -04 | 2007.01
Specifications - Detectors and Bases
Installation Manual
Bosch Security Systems, Inc.
4998138694Er7.book Page 9 Thursday, March 1, 2007 8:42 AM
F220 Series Detectors with F220-B6/C/E/R Bases
2.3.2
General Information | en
9
Base Specifications
Alarm Current (only base current, detector current excluded)
F220-B6:
Two-wire base; no base current
F220-B6C:
31 mA at 12 VDC
35 mA at 24 VDC
40 mA maximum at 30 VDC
25 mA at 12 VDC
F220-B6E:
30 mA at 24 VDC
34 mA maximum at 30 VDC
13.5 mA at 12 VDC
F220-B6R:
16.5 mA at 24 VDC
19 mA maximum at 30 VDC
Standby Current
F220-B6/C/R:
No current draw in standby
F220-B6E:
16 mA maximum at 30 VDC
Voltage
F220-B6 (two-wire):
8.5 VDC to 32.0 VDC
F220-B6C/E/R (four-wire): 10.0 VDC to 30.0 VDC
Table 2.4 F220-B6 Series Base Specifications
2.3.3
Detector Specifications
Current
Alarm:
Standby:
Startup:
Powerup Time
Rate of Rise
F220-135:
Voltage
Operating:
RMS Ripple:
20 mA minimum at 8.5 VDC
35 mA maximum at 32 VDC
0.12 mA maximum
0.12 mA maximum
22 second maximum
15°F/min (9°C/min) or greater
8.5 VDC to 32.0 VDC
25% of DC input
Table 2.5 F220 Series Detector Heads Specifications
2.4
Electrical Supervision
When the F220-B6 Series Bases are wired according to the
instructions in this document, the control panel initiates a
trouble signal when a detector is removed from its base,
Bosch Security Systems, Inc.
Installation Manual
4998138694 -04 | 2007.01
4998138694Er7.book Page 10 Thursday, March 1, 2007 8:42 AM
10 en | Install the Bases
F220 Series Detectors with F220-B6/C/E/R Bases
providing tamper protection. An EOL power supervision
module, such as a D275 or an F220-B6E Power Supervision
Base and an EOL resistor as specified by the control panel
manufacturer, supervises power.
3
Install the Bases
3.1
Mount the Bases
With the exception of the F220-B6E base, all four-wire bases
can be used in any combination within a loop. One F220-B6E
Power Supervision Base can be used as the last base on a loop
in four-wire systems to provide power supervision.
i
NOTE! Follow NFPA 72 guidelines for mounting locations.
For commercial and industrial installations, 30 ft (9 m)
spacing between smoke detectors is recommended.
1.
Release the mounting skirt from the mounting base. Use a
screwdriver at the location of the snap locks (refer to
Figure 2.1, item 12, page 5) to release the mounting skirt.
2.
3.
Run all system wiring (refer to Section 3.2 Wire the Bases).
Mount the base using the two oblong mounting holes. Fits
4 in. square, octagon, AB, and single-gang back boxes.
i
NOTE! Depending on local regulations, you can surface
mount the bases using anchors, mollies, or wing nuts, or
you can mount directly on back boxes.
NOTE! The electrical box must be large enough to
i
accommodate the number and size of conductors
specified by the National Electrical Code or any local
authorities having jurisdiction (AHJ).
4.
Tighten the base to the mounting surface. Tighten until
snug, but not distorted.
4998138694 -04 | 2007.01
Installation Manual
Bosch Security Systems, Inc.
4998138694Er7.book Page 11 Thursday, March 1, 2007 8:42 AM
F220 Series Detectors with F220-B6/C/E/R Bases
3.2
Install the Bases | en 11
Wire the Bases
CAUTION! When wiring bases, all terminal screws
!
3.2.1
including those not wired must be tightened to prevent
loose screw heads from making intermitent electrical
contact with the detector head.
Terminal Connections
WARNING! Do not twist or loop the wires around the
terminals. In and out wires for terminal connection must
!
be cut, stripped, and inserted as individual ends.
NOTE! Bring the positive (+) wires in on terminal b2 and
i
3.2.2
out from terminal b1. Use a consistent pattern, inputting
on b2 and outputting from b1. The negative (-) wires
input and output from the same terminal (a1/a2).
EOL Resistors
Use the EOL resistors supplied or specified by the control panel
manufacturer. This applies to all loop terminations including the
D275 Module and the F220-B6E Power Supervision Base.
3.2.3
Loop Wiring Specifications
In a two-wire system, the maximum loop length depends on the
number of F220-B6 bases on the loop, the wire size, and the
control panel specifications. Refer to the control panel's
installation instructions for specific wiring information.
In a four-wire system, the maximum loop length and number of
bases that can be placed on a loop depend on the voltage drop
on the power circuit. Use standard voltage drop calculations to
ensure that the last detector on the loop meets the minimum
voltage requirement of at least 10 V.
Bosch Security Systems, Inc.
Installation Manual
4998138694 -04 | 2007.01
4998138694Er7.book Page 12 Thursday, March 1, 2007 8:42 AM
12 en | Install the Bases
3.2.4
F220 Series Detectors with F220-B6/C/E/R Bases
Four-wire Loop Termination
One D275 End-of-Line Module (refer to Figure 3.6 on page 17)
or F220-B6E Power Supervision Base (refer to Figure 3.4 on
page 15) is required for each loop when using four-wire bases.
3.3
Wire Optional Remote Annunciators
If using the optional DRA-5 Remote Alarm Indicator, connect the
positive (red) wire to terminal b1 and the negative wire (white)
to terminal c (refer to Figure 3.1).
1
DRA-5
b2 b1
4 3
5
1.
2
a1/a2 c
2
1
Red wire to Terminal b1
2.
on base
Fig. 3.1
White wire to Terminal c
on base
Optional DRA-5 Remote Annunciator Wiring
4998138694 -04 | 2007.01
Installation Manual
Bosch Security Systems, Inc.
4998138694Er7.book Page 13 Thursday, March 1, 2007 8:42 AM
Install the Bases | en 13
F220 Series Detectors with F220-B6/C/E/R Bases
3.4
Wire F220-B6 Two-wire Bases
The F220-B6 is a 12 VDC or 24 VDC base for two-wire
conventional loops. Refer to Figure 3.2 for wiring details.
1
-
-
+
+
2
F220-B6
b2 b1
4 3
5
1.
1
Initiating device circuit
2.
a1/a2 c
2
1
Place the EOL resistor
(IDC) input (positive [+] in
across base’s power
on terminal b2, out from
terminals (b2 and a1/a2)
terminal b1; negative [-] in
of the last base on the
and out from terminal
loop. Refer to the control
a1/a2) from the control
panel installation
panel or from a previous
instructions for resistor
two-wire base and output
specifications.
to the next two-wire base.
Fig. 3.2
3.5
Wiring F220-B6 Two-wire Bases
Wire F220-B6C/E/R Four-wire Bases
!
CAUTION! Do not connect relays to inductive or
capacitive loads. Use with resistive loads only.
Bosch Security Systems, Inc.
Installation Manual
4998138694 -04 | 2007.01
4998138694Er7.book Page 14 Thursday, March 1, 2007 8:42 AM
14 en | Install the Bases
3.5.1
F220 Series Detectors with F220-B6/C/E/R Bases
F220-B6C:
The F220-B6C base has a normally open alarm loop relay and
auxiliary Form C (NC/C/NO) contacts. The contacts are rated
for 0.5 A at 120 VAC/DC for resistive loads. Refer to Figure 3.3
for wiring details.
_
1
1
+
b2 b1
F220-B6C
3
2
1.
2.
NO
5
3
2
+
+
_
_
4
C
a1/a2 c
NC
1
2
Power input (positive [+]
from terminal 4) from the
in on terminal b2, out from
control panel or from a
terminal b1; negative [-] in
previous four-wire base
and out from terminal
and output to the next
a1/a2) from the control
four-wire base or to loop
panel or from a previous
termination (refer to
four-wire base and output
Figure 3.4 on page 15
to the next four-wire base.
[F220-B6E] or Figure 3.6
Initiating device circuit
on page 17 [D275]).
(IDC) input (positive [+]
3.
Alarm Loop Relay
inand out from terminal 5 4.
Auxiliary Form C Alarm
and negative [-] in and out
Relay
Fig. 3.3
3.5.2
4
C NO
Wiring F220-B6C Four-wire Bases
F220-B6E:
The F220-B6E Power Supervision Base has a normally-open
alarm loop relay that activates when the unit is in alarm and a
power supervision relay that activates when power is supplied.
Separate power supervision devices, such as the D275, are
4998138694 -04 | 2007.01
Installation Manual
Bosch Security Systems, Inc.
4998138694Er7.book Page 15 Thursday, March 1, 2007 8:42 AM
Install the Bases | en 15
F220 Series Detectors with F220-B6/C/E/R Bases
unnecessary. Use only one F220-B6E per zone run. It must be
the last base on the run. Refer to Figure 3.4 for wiring details.
_
1
+
4
b2 b1
F220-B6E*
5
2
1.
2.
C
4
NO 3
5
a1/a2 c
C
2 NO
1
6
3
+
_
Power input (positive [+]
previous four-wire base.
in on terminal b2; negative 3.
Jumper connecting
[-] in on terminal a1/a2)
terminals 2 and 3.
from the control panel or 4.
Place an appropriate EOL
from a previous four-wire
resistor (refer to the
base.
control panel’s installation
Initiating device circuit
instructions for resistor
(IDC) input (positive [+] to
specifications) across
terminal 2 and negative [-]
Terminals 1 and 4.
to terminal 1) from the
5.
Power Supervision Relay
control panel or from a
6.
Alarm Loop Relay
Fig. 3.4
Wiring F220-B6E Four-wire Power Supervision Bases
* F220-B6E Bases can only be used at the end of a loop.
The alarm loop relay (Form A, Terminals 1 and 2) and the power
supervision relay (Terminal 3 and 4) are rated for 0.5 A at
120 VAC/DC for resistive loads.
Bosch Security Systems, Inc.
Installation Manual
4998138694 -04 | 2007.01
4998138694Er7.book Page 16 Thursday, March 1, 2007 8:42 AM
16 en | Install the Bases
3.5.3
F220 Series Detectors with F220-B6/C/E/R Bases
F220-B6R:
The F220-B6R is the standard base for four-wire configurations.
The Alarm Loop Relay (Terminals 1 and 2) is a normally-open
relay rated for 0.5 A at 120 VAC/DC. The relay closes on alarm.
Refer to Figure 3.5 for wiring details.
1
_
_
+
+
F220-B6R
b2 b1
a1/a2 c
C
4 3
5
+
2
.
1.
2.
1
2
NO
3
1
+
_
_
2
Resettable auxiliary power
and negative [-] in and out
input (positive [+] in on
from terminal 1) from the
terminal b2, out from ter-
control panel or from a
minal b1; negative [-] in
previous four-wire base
and out from terminal
and output to the next
a1/a2) from the control
four-wire base or to loop
panel or from a previous
termination (refer to
four-wire base and output
Figure 3.4 on page 15
to the next four-wire base.
[F220-B6E] or Figure 3.6
Initiating device circuit
on page 17 [D275]).
(IDC) input (positive [+] in 3.
Alarm Loop Relay
and out from terminal 2
Fig. 3.5
Wiring F220-B6R Standard Four-wire Bases
4998138694 -04 | 2007.01
Installation Manual
Bosch Security Systems, Inc.
4998138694Er7.book Page 17 Thursday, March 1, 2007 8:42 AM
Install the Bases | en 17
F220 Series Detectors with F220-B6/C/E/R Bases
3.6
3.6.1
Wire Power Supervision Modules
Wire F220-B6E Power Supervision Base
Refer to Section 3.5.2 F220-B6E: for F220-B6E wiring
instructions.
3.6.2
Wire D275 Power Supervision Module
When a D275 Module (refer to Figure 3.6) is used with 12 VDC
systems, connect the red wire to the output terminal (b1) on
the last base in the run. The yellow wire remains unconnected.
For 24 VDC systems, connect the yellow wire to the output
terminal (b1). The red wire remains unconnected.
1
2
3
D275
2
4
7
5
+24 VDC
6
1.
2.
3.
Common (-)
EOL resistor (refer to the
control panel’s
+12 VDC
base on the loop.
4.
Red wire to Terminal b1
installation instructions
on last base on loop for
for specifications).
12 VDC systems.
The positive (+) and
5.
Yellow wire to Terminal b1
negative (-) IDC wires
on last base on loop for
(blue) from the D275.
24 VDC systems.
Connect the positive (+)
6.
IDC wire through the EOL
resistor to Terminal 2 and
the negative (-) IDC wire
base on loop.
7.
to Terminal 1 on the last
Fig. 3.6
Black wire (common) to
Terminal a1/a2 on last
Power loop: Use either red
or yellow wire; not both.
Wiring a D275 Power Supervision Module as a Loop Terminator
Bosch Security Systems, Inc.
Installation Manual
4998138694 -04 | 2007.01
4998138694Er7.book Page 18 Thursday, March 1, 2007 8:42 AM
18 en | Install the Detector Heads
F220 Series Detectors with F220-B6/C/E/R Bases
4
Install the Detector Heads
4.1
Mount the Detector Heads
CAUTION! Before mounting detector heads, all terminal
!
4.1.1
screws in the bases including those not wired must be
tightened to prevent loose screw heads from making
intermitent electrical contact with the detector head.
Optional Locking Bar
Each base has a snap-off locking bar as part of the base
molding. Engage the locking bar to prohibit unauthorized
detector removal. To engage the locking bar, move it to the
position shown in Figure 4.1. (See also Figure 4.2, Items 4 and 9
on page 19.)
1
2
X
X
1.
Snap locking bar (X) off
2.
base molding
Insert locking bar (X) into
locking bar mount until
fully engaged
Fig. 4.1
Engaging the Locking Bar
CAUTION! When using the locking bar, before installing
!
the detector head, open the unlocking port (refer to
Figure 4.2, Item 4) by poking through the plastic with a
screwdriver.
4998138694 -04 | 2007.01
Installation Manual
Bosch Security Systems, Inc.
4998138694Er7.book Page 19 Thursday, March 1, 2007 8:42 AM
Install the Detector Heads | en 19
F220 Series Detectors with F220-B6/C/E/R Bases
4.1.2
Mounting Skirt
Align the four alignment keys (refer to Figure 2.1, Item 11 on
page 5 and to Figure 4.2, Item 5) and press the skirt firmly
down onto the mounting base (refer to Figure 4.2, Item 3) to
engage the snap locks.
6
1
7
8
5
2
4
5
5
3
5
9
1.
Detector head (heat
the mounting skirt and
detector shown in exam-
four corresponding places
ple)
on the base)
2.
Mounting skirt
6.
LED
3.
Mounting base
7.
Bar on mounting skirt
4.
Locking port
8.
T mark on mounting skirt
5.
Alignment keys (four
9.
Locking bar in locked
places on the bottom of
Fig. 4.2
position
Part Orientation for Mounting
Bosch Security Systems, Inc.
Installation Manual
4998138694 -04 | 2007.01
4998138694Er7.book Page 20 Thursday, March 1, 2007 8:42 AM
20 en | Install the Detector Heads
4.1.3
!
F220 Series Detectors with F220-B6/C/E/R Bases
Detector Head
CAUTION! The mounting skirts and detector heads are
keyed. Do not force them onto the mounting bases.
Install:
Install the detector head by lining up the LED on the detector
head (refer to Figure 4.2, Item 6 on page 19) with the bar on the
mounting skirt (refer to Figure 4.2, Item 7). Turn the detector
head clockwise until the LED aligns with the T mark on the
mounting skirt (refer to Figure 4.2, Item 8).
Remove:
Remove the detector head by turning it counter-clockwise. If
the optional locking bar is used, refer to Figure 4.3.
2
1
1.
Insert screwdriver through the 2.
Hold the locking bar down
locking port and depress the
while turning the head
locking bar.
counter-clockwise until
disengaged.
Fig. 4.3
Unlocking the Locking Bar
4998138694 -04 | 2007.01
Installation Manual
Bosch Security Systems, Inc.
4998138694Er7.book Page 21 Thursday, March 1, 2007 8:42 AM
F220 Series Detectors with F220-B6/C/E/R Bases
4.2
Install the Detector Heads | en 21
Set Detector Modes
The F220 Series Smoke Detectors feature a unique
magnet-operated sensitivity mode and detector test mode.
4.2.1
Test Mode
Test the detector by placing the magnet next to the T mark on
the mounting skirt (refer to Figure 4.2, Item 8 on page 19) for
three consecutive flashes to cause an alarm.
4.2.2
Sensitivity Mode
If the magnet is next to the T mark for less than three flashes
but more than one flash, the detector enters Sensitivity Mode.
1.
Place the detector into Sensitivity Mode.
2.
Wait for the first single green LED flash.
3.
Count the number of red LED flashes that follow and refer
to Table 4.1 for sensitivity definitions.
Number of
Sensitivity Definition (% Obscuration)
Red Flashes
1
Malfunctioning smoke or heat detector
3
Normally operating smoke or heat detector with
4 to 6
7 to 10
little or no dirt contamination
Progressively more contamination
Trouble condition, very dirty but still
compensated to 3%/ft (3%/ft = 0.433 db/m);
11
12
Sensitivity < 3%/ft at 10 flashes.
Sensitivity < 2.5%/ft (2.5%/ft = 0.36 db/m)
Sensitivity < 2.0%/ft (2.0%/ft = 0.287 db/m),
13
14
chance of false alarm increases
Sensitivity < 1.5%/ft (1.5%/ft = 0.214 db/m)
Sensitivity < 1.0%/ft (1.0%/ft = 0.143 db/m),
15
chance of false alarm greatly increases
Sensitivity < 0.5%/ft (0.5%/ft = 0.071 db/m),
false alarm likely
Table 4.1 Red LED Flash Definition
4.
The detector exits sensitivity mode and returns to one
green LED flash every eight seconds.
Bosch Security Systems, Inc.
Installation Manual
4998138694 -04 | 2007.01
4998138694Er7.book Page 22 Thursday, March 1, 2007 8:42 AM
22 en | Install the Detector Heads
4.3
F220 Series Detectors with F220-B6/C/E/R Bases
Set CleanMe Feature
The Clean Me feature monitors the smoke chamber’s sensitivity
and sends a trouble signal to the control panel when the
sensitivity degrades to a preset level.
i
NOTE! When a CleanMe signal is sent to a control panel
that is not CleanMe compatible, the signal may be
misinterpreted as an alarm.
To activate the CleanMe feature:
1.
Put the detector into sensitivity mode by placing a magnet
next to the T mark on the mounting skirt (refer to
Figure 4.2, Item 8 on page 19). Remove the magnet after
the first red LED flash and before the third red LED flash.
2.
When the magnet is removed, the LED flashes green once
and shows the first of two sensitivity displays.
3.
When the LED next flashes red, replace the magnet near
the T mark(refer to Figure 4.2, Item 8 on page 19).
4.
Hold the magnet against the T mark on the mounting skirt
(refer to Figure 4.2, Item 8 on page 19) until the green LED
flashes twice and the red LED repeats the sensitivity
indication.
5.
The detector exits sensitivity mode. If CleanMe has been
successfully enabled, the green LED flashes twice in rapid
succession every eight seconds indicating that CleanMe is
activated.
To disable CleanMe, repeat this process and verify the double
flash returns to a single flash.
4.4
Flash Rate and Trouble Indication
These detectors include the Chamber Check Automatic Trouble
Indicator that verifies the detector’s calibration is within the
factory listed range. NFPA guidelines for sensitivity testing can
be met by visually inspecting the detector and checking the
flash rate of the LED.
4998138694 -04 | 2007.01
Installation Manual
Bosch Security Systems, Inc.
4998138694Er7.book Page 23 Thursday, March 1, 2007 8:42 AM
F220 Series Detectors with F220-B6/C/E/R Bases
Test the Installation | en 23
NOTE! Perform the visual check before resetting power.
i
After a reset the trouble indicators clear for 70 seconds.
After 70 seconds, if the detector is in a trouble condition,
trouble indications begin again.
A unit with CleanMe activated double flashes (two flashes
within a half second of each other) every eight seconds. A
normally operating unit flashes once every eight seconds. If a
detector is in a trouble condition due to a dirty lens or a sensor
malfunction, it single or double flashes every four seconds. If
enabled, the CleanMe trouble signal is sent.
5
Test the Installation
5.1
Inspect the Installation
1.
Check the wiring from the control panel to the last head on
each run for proper polarity and continuity.
2.
Terminate each run with an EOL resistor as specified by
the control panel manufacturer.
3.
Terminate four-wire runs with EOL power supervision
modules or F220-B6E bases.
4.
Apply power to the system. Check for alarms and troubles.
5.
Note which detectors alarmed (if any), shut down the
system, remove alarmed detectors from their bases, and
recheck the bases for proper wiring.
6.
If the problem persists, determine if the problem is caused
by the detector or the base. Replace the affected detectors
or bases with known good units.
7.
If a system alarm occurs with no detector alarms present,
remove all detectors and check the wiring at each base.
8.
9.
Check the wiring of each EOL resistor and EOL module.
When the system is alarm free, check each detector to
ensure that the green LED indicator flashes approximately
Bosch Security Systems, Inc.
Installation Manual
4998138694 -04 | 2007.01
4998138694Er7.book Page 24 Thursday, March 1, 2007 8:42 AM
24 en | Test the Installation
F220 Series Detectors with F220-B6/C/E/R Bases
every eight seconds. This verifies the detector is receiving
power and operating properly.
NOTE! If a heat detector LED flashes at a rate of
i
4 flashes/sec, the detector is either cold (below +32°F
[0°C]), out of sensitivity range, or defective. If a smoke
detector flashes at a rate of 4 flashes/sec, it is either out
of sensitivity range or defective.
5.2
Test Each Detector
Test each detector to ensure it causes a control panel alarm.
Reset the control panel after each test.
5.2.1
Activate an Alarm at Each Detector
To cause heat detectors to alarm either:
–
Activate the internal reed switch by placing a magnet
horizontally against the T mark on the mounting skirt (refer
to Figure 4.2, Item 8 on page 19) and holding it there for
three consecutive LED flashes, or
–
Expose the thermistor (refer to Figure 2.2, Item 3 on
page 7)to a heat source such as a hair dryer or a shielded
heat lamp until the detector alarms and the alarm LED
lights .
To cause smoke detectors to alarm either:
–
Activate the internal reed switch by placing a magnet
horizontally against the T mark on the mounting skirt (refer
to Figure 4.2, Item 8 on page 19) and holding it there for
three consecutive LED flashes, or
–
Use a UL Listed aerosol smoke detector tester to simulate
an alarm. Follow the instructions provided with the aerosol
smoke detector tester.
5.2.2
Reset the Control Panel
When a detector alarms, the red LED indicator activates and
latches into the ON position. Clear the alarm by momentarily
removing power before proceeding to the next detector.
4998138694 -04 | 2007.01
Installation Manual
Bosch Security Systems, Inc.
4998138694Er7.book Page 25 Thursday, March 1, 2007 8:42 AM
F220 Series Detectors with F220-B6/C/E/R Bases
5.3
Test the Installation | en 25
Test the Alarm Loop
Checkthe voltage across the EOL resistor of each alarm loop to
verify wiring losses do not exceed control panel manufacturer’s
specifications.
5.4
Test CO Sensors
Removing the detector head or resetting the detector’s power
places the detector in a special test mode for 15 minutes. If
over 35 ppm of CO is applied to the detector within this
15-minute period, the detector must alarm or it is defective.
!
5.5
WARNING! The F220-PTHC detects carbon monoxide
(CO) as a component of a fire. Do not use the F220-PTHC
as a stand-alone CO detector.
Perform NFPA 72 Required Testing
Refer to Section 1.2 Required Maintenance and Testing on
page 2.
Bosch Security Systems, Inc.
Installation Manual
4998138694 -04 | 2007.01
4998138694Er7.book Page 26 Thursday, March 1, 2007 8:42 AM
26 en | Test the Installation
4998138694 -04 | 2007.01
F220 Series Detectors with F220-B6/C/E/R Bases
Installation Manual
Bosch Security Systems, Inc.
4998138694Er7.book Page 27 Thursday, March 1, 2007 8:42 AM
F220 Series Detectors with F220-B6/C/E/R Bases
Bosch Security Systems, Inc.
Installation Manual
Test the Installation | en 27
4998138694 -04 | 2007.01
4998138694Er7.book Page 28 Thursday, March 1, 2007 8:42 AM
Bosch Security Systems, Inc.
130 Perinton Parkway
Fairport, NY 14450-9199
USA
Customer Service: (800) 289-0096
Technical Support: (888) 886-6189
www.boschsecurity.us
© Bosch Security Systems, Inc., 2007
Download PDF

advertising