INSTALLATION
INSTRUCTIONS
PARTS LIST
Rear Camera Attachment Kit
P/N 08B77-TA0-100
Rear camera bracket
Accessory
REAR CAMERA
ATTACHMENT KIT
Application
2010 ACCORD
4-DOOR
2 Well-nuts
2 Wire ties with clip A
Publications No.
AII 42270
Issue Date
AUG 2009
Rear camera trim
6-Pin connector
7 Wire ties with clip B
Rear camera harness
37 Wire ties
Template
4 Clips A
EPT sealer
Clip B
2 Washer-screws, 4 x 14 mm
Grommet
4 Nuts
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
AII 42270 (0908) 08B77-TA0-1000-91
1 of 16
2 Clips C
2 Tapes
Accessory User’s Information Manual
Rear Camera
P/N 08A77-6K1-370
Rear camera
2 Screws, 3 x 6 mm
TOOLS AND SUPPLIES REQUIRED
Phillips screwdriver
Flat-tip screwdriver
Ratchet
8 mm and 10 mm Socket
Pushpin
Felt-tip pen
Drill
3 mm, 5 mm, 6 mm, 8 mm, and 10 mm Drill bit
Ruler
Eye protection (safety goggles, face shield, etc.)
10 mm Combination wrench
File
Diagonal cutters
Utility knife
Scissors
Center punch
Hacksaw blade
Touch-up paint
Electrical tape
Illustration of the Rear Camera Attachment Kit
Installed on the Vehicle
2 of 16
REAR CAMERA
REAR CAMERA
HARNESS
7201010Y
AII 42270 (0908) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
INSTALLATION
Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by
“do-it-yourselfers.”
Install the backup camera first if both the backup camera and a trailer hitch are to be mounted on the vehicle.
1.
Make sure you have the anti-theft codes for the radio and navigation system (if equipped), then write down the radio presets.
2.
Disconnect the negative cable from the battery.
3.
V6 MODEL only: Remove the passenger’s dashboard under cover (three clips and two pins).
4.
Release the glove box (damper and two stops).
2 STOPS
PIN
GLOVE BOX
5.
Remove the glove box (two screws).
DAMPER
7112020Y
CLIPS
PIN
PASSENGER’S DASHBOARD
UNDER COVER
730101AY
GLOVE BOX
SCREWS 7112030Y
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
AII 42270 (0908)
3 of 16
6.
Remove the right front side step trim (four clips).
RIGHT FRONT SIDE
STEP TRIM
4 CLIPS
9.
Remove the rear seat cushion (one bolt and release the two hooks).
REAR SEAT
CUSHION
7125030E
7.
Pull away the front door opening seal in the area shown.
2 CLIPS
FRONT DOOR
OPENING SEAL
10. Remove the right seat side bolster (one bolt and release the one hook).
REAR SEAT
SIDE BOLSTER
HOOK
RIGHT KICK PANEL
8.
Remove the right kick panel (two clips).
7115010E
BOLT
7111030E
4 of 16
AII 42270 (0908) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
11. Remove the right rear side step trim (four clips).
RIGHT REAR SIDE
STEP TRIM
14. Fold down the rear seat back by pulling the lever under the rear parcel shelf inside the trunk.
REAR SEAT BACK
REAR PARCEL
SHELF
Down.
FRONT
4 CLIPS
711601AE
12. Pull away the door opening seal in the area shown.
RETAINING
TAB
DOOR OPENING SEAL
(Remove.)
FRONT
LEVER
(Pull.)
15. Remove the trunk floor mat (one clip).
CLIP
7220190E
TRUNK
FLOOR MAT
CENTER LOWER
COVER
CLIP
7112050E
13. Remove the right center lower cover (one clip and four retaining tabs).
7109070E
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
AII 42270 (0908)
5 of 16
16. Remove the rear trim panel (four clips and three hooks).
REAR TRIM PANEL
4 CLIPS
18. V6 MODEL only: Remove the trunk lid lining (12 clips).
CLIP
3 HOOKS
17. Remove the right trunk side lining (five clips).
710906AE
TRUNK LID
LINING
11 CLIPS
711502AE
19. Remove four bolts and two clips from the license plate trim. Remove the license plate.
3 CLIPS
RIGHT TRUNK
SIDE LINING
4 BOLTS
LICENSE
PLATE TRIM
2 CLIPS
722018AE
CLIPS
(Reuse.)
751805AE
6 of 16
AII 42270 (0908) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
20. Insert the KTC trim tool (AP201-W) between the license plate trim and the trunk lid. Move the tool left and right to peel off the double-sided tape in between.
22. Slide the license plate trim down, and disengage the top two clips to remove the license plate trim.
Pull down and disengage the top two clips from the top of the license plate trim
TOP
CLIPS
(Discard.)
DOUBLE-SIDED
TAPE
LICENSE
PLATE TRIM
TRUNK LID KTC TRIM TOOL
(AP201-W)
751806BE
21. Pull out on the license plate trim and disengage the lower three clips. Do not remove the license plate trim yet.
TRUNK LID
5 CLIPS
(Discard.) LICENSE
PLATE TRIM 711505BE
23. Remove and discard the top two clips from the trunk lid.
24. Using scissors, cut out the marked area for template A along the dotted lines.
SCISSORS
TEMPLATE A
3 CLIPS
LICENSE
PLATE TRIM
762101AE
TEMPLATE
7307120B
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
AII 42270 (0908)
7 of 16
25. Tape template A on the trunk lid as shown.
Lightly center punch the trunk lid at each of the three marks indicated on template A. Remove template A.
TEMPLATE A
MARK
TAPE
MARK
TRUNK LID
27. Install two well-nuts into the 8 mm holes.
8 mm HOLE
TRUNK LID
VEHICLE
HOLE
VEHICLE
HOLE
TAPE
CENTER
PUNCH MARK
26. While wearing eye protection, drill the trunk lid at each center-punched mark:
• Wrap each drill bit with electrical tape 15 mm from the tip, or use a drill stop.
• Drill all three center-punched marks to 8 mm.
First drill with a 3 mm drill bit, then with a 6 mm drill, and finish with an 8 mm drill bit.
• Enlarge the bottom hole in the trunk lid to 10 mm using a 10 mm drill bit.
• Remove any burrs, and apply touch-up paint to each drilled hole. Allow the touch-up paint to dry before proceeding to the next step.
WELL-NUTS
7201051Y
28. Route the rear camera cord through the rear camera bracket, and install the rear camera to the rear camera bracket using the 3 x 6 mm screws.
REAR CAMERA
REAR CAMERA
BRACKET
3 x 6 mm
SCREW
LABEL
MARK
TRUNK LID
REAR CAMERA
CORD
3 x 6 mm
SCREW
7201081Y
15 mm
DRILL
(3 mm bit
6 mm bit
8 mm bit) DRILL
(3 mm bit
6 mm bit
8 mm bit
10 mm bit)
ELECTRICAL TAPE
(Wrap electrical tape around the drill bit.)
7201041Y
8 of 16
AII 42270 (0908) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
29. Wrap the terminals of the rear camera cord with electrical tape.
REAR CAMERA
BRACKET
CAMERA
CONNECTOR
END
ELECTRICAL TAPE
(Wrap around the terminals of the rear camera.)
GROMMET
TERMINAL
33. Route the rear camera cord along the right side of the trunk lid, and remove the electrical tape from the terminals.
VEHICLE PANEL
VEHICLE
HARNESS
TRUNK LID
OPENER CABLE
REAR CAMERA
CORD
TRUNK LID REAR CAMERA
CORD
REAR
CAMERA
Align the grommet end with rear camera connector end.
ELECTRICAL TAPE
(Wrap around the end of the grommet.)
REAR CAMERA
CORD
7201091Y
30. Route the rear camera cord through the grommet.
Secure the cord to the grommet with electrical tape at the indicated position. Note the direction of the grommet.
31. Route the rear camera cord through the 10 mm hole in the trunk lid and seat the grommet in the
10 mm hole.
8 mm HOLE
10 mm HOLE
TRUNK
LID
SECTIONAL VIEW
4 x 14 mm
WASHER-
SCREW
REAR
CAMERA
REAR CAMERA
CORD
TRUNK LID
GROMMET
720110AY
32. Install the rear camera assembly to the trunk lid using the two 4 x 14 mm washer-screws.
ELECTRICAL
TAPE
34. Remove the terminal lock from the 6-pin connector.
Insert the rear camera terminals into the 6-pin connector. Verify each terminal position, and then reinstall the terminal lock.
NOTE: Make sure to install the wires as shown in the illustration (The black and brown wires do not match up.)
YELLOW
WHITE
BLUE/BLACK
BLACK
BROWN
RED
YELLOW
WHITE
BLUE/BLACK
BROWN
BLACK
RED
LOCK
Viewed from harness side
6-PIN
CONNECTOR RED
BLACK
6-PIN
CONNECTOR
6 TERMINALS YELLOW
WHITE
BROWN
BLUE/
BLACK
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
AII 42270 (0908)
9 of 16
35. Route the rear camera harness through the trunk lid hole, and plug the rear camera cord 6-pin connector into the rear camera harness 6-pin connector.
6-PIN
CONNECTOR
6-PIN
CONNECTOR
WIRE TIE
37. Secure the rear camera cord to the vehicle harness with one wire tie.
VEHICLE
HARNESS
WIRE TIE
REAR CAMERA
CORD
TRUNK SPOILER
HARNESS
WIRE TIE
WITH CLIP B
Insert into round hole.
WIRE TIE
WITH
CLIP B
VEHICLE
FRAME
WIRE TIE
WITH CLIP B
Insert into round hole.
WIRE TIE
REAR CAMERA
HARNESS
TRUNK SPOILER
HARNESS
REAR CAMERA
HARNESS
720112CY
36. Secure the rear camera cord and the rear camera harness to the vehicle panel with three wire ties with clip B.
NOTE: If a trunk spoiler is installed, secure the rear camera cord to the trunk spoiler harness with two wire ties.
TRUNK LID
REAR
CAMERA
CORD
EPT SEALER
(Cut in half.)
720113DY
38. Bundle up the excess rear camera cord, and secure it to the vehicle harness with one wire tie.
39. Using scissors, cut one EPT sealer in half. Attach half of the EPT sealer to the vehicle frame.
10 of 16
AII 42270 (0908) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
40. Route the rear camera harness along the trunk lid hinge, and secure it to the holes in the hinge using four wire ties with clip B.
NOTE: If a trunk spoiler is installed, secure the rear camera harness to the trunk spoiler harness using four wire ties.
TRUNK SPOILER
HARNESS
4 WIRE TIES
REAR CAMERA
HARNESS
42. Route the rear camera harness towards the rear of the vehicle, and secure it to the vehicle panel hole with one wire tie with clip A.
NOTE: If a trunk spoiler is installed, secure the rear camera harness to the trunk spoiler harness with one wire tie.
TRUNK LID
HINGE
VEHICLE
PANEL
WIRE TIE
WITH CLIP A
FRONT
TRUNK LID
HINGE
WIRE TIES
WITH CLIP B
FRONT
WIRE
TIE
TRUNK SPOILER
HARNESS
REAR CAMERA
HARNESS
REAR
CAMERA
HARNESS
730713BB
GREEN
TAPE
REAR CAMERA
HARNESS
720114BY
41. Route the rear camera harness towards the rear of the vehicle, and secure it to the vehicle panel hole with one wire tie with clip A.
NOTE: If a trunk spoiler is installed, secure the rear camera harness to the trunk spoiler harness with one wire tie.
TRUNK LID
HINGE
GREEN TAPE
TRUNK SPOILER
HARNESS
WIRE TIE
REAR
CAMERA
HARNESS
FRONT
VEHICLE
PANEL
GREEN
TAPE
WIRE TIE
WITH CLIP A
REAR CAMERA
HARNESS
7201151Y
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
AII 42270 (0908)
11 of 16
43. Route the rear camera harness along the vehicle harness, and secure it to the vehicle harness with six wire ties.
WIRE TIES
VEHICLE
HARNESS
WIRE TIES
45. Route the rear camera harness forward along the vehicle harness, and secure it to the vehicle harness with four wire ties.
WIRE TIES
VEHICLE
HARNESS
WIRE TIES
VEHICLE
HARNESS
REAR
SEAT
FRONT
WIRE TIES
REAR CAMERA
HARNESS
FRONT
TRUNK 720116BY
44. Route the rear camera harness forward along the vehicle harness towards the front of the vehicle, and secure it to the vehicle harness with one wire tie.
REAR CAMERA
HARNESS
7201181Y
46. Route the rear camera harness forward past the “B” pillar, and secure it to the vehicle harness with three wire ties.
“B”
PILLAR
VEHICLE
HARNESS
WIRE TIES
FRONT
FRONT
WIRE TIE
REAR CAMERA
HARNESS
GREEN
TAPE
REAR
CAMERA
HARNESS
VEHICLE
HARNESS
VEHICLE
HARNESS
WIRE
TIE
REAR
CAMERA
HARNESS
7201191Y
REAR CAMERA
HARNESS
12 of 16
TRUNK
7201170Y
AII 42270 (0908) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
47. Route the rear camera harness through the passenger’s door opening, and secure it to the vehicle harness with five wire ties.
REAR
CAMERA
HARNESS
GREEN
TAPE
VEHICLE
HARNESS
PASSENGER’S
SEAT
REAR
CAMERA
HARNESS
49. At the glove box opening, locate and remove the tape securing the 6-pin vehicle connector.
50. Plug the 6-pin vehicle connector into the rear camera harness 6-pin connector. Secure the 6-pin connector to the vehicle harness with one wire tie.
VEHICLE
HARNESS
WIRE
TIE
6-PIN
CONNECTOR
REAR CAMERA
HARNESS
WIRE
TIE
WIRE
TIE
VEHICLE
HARNESS
FRONT
WIRE TIES 72
48. Route the rear camera harness up through the glove box opening, and secure it to the vehicle harness with five wire ties.
VEHICLE
HARNESS
WIRE TIES VEHICLE
HARNESS
VEHICLE
HARNESS
6-PIN
CONNECTOR
TAPE
GLOVE BOX
OPENING
720122AY
51. Using scissors, cut out the marked area for template B along the dotted lines.
SCISSORS
TEMPLATE
VEHICLE
CLIP
GLOVE BOX
OPENING
VEHICLE
HARNESS
WIRE TIES
REAR CAMERA
HARNESS
7201211Y
TEMPLATE B
7307120B
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
AII 42270 (0908)
13 of 16
52. Attach template B to the license plate trim using tape.
TEMPLATE B
TAPE LICENSE
PLATE TRIM
55. While wearing eye protection, drill the license plate trim at each mark.
• First drill all five holes with a 3 mm drill bit, and then with a 6 mm drill bit.
• Enlarge just the bottom holes to 10 mm using a
10 mm drill bit.
LICENSE
PLATE TRIM
DRILL
(3 mm bit
6 mm bit)
MARK
RIB
TAPE
RIB
730801AB
53. Using a pushpin, mark the license plate trim at the five locations.
54. Using a utility knife, scribe along the inner line of template B, and peel off the template.
INNER LINE
4 mm
4 mm
LICENSE
PLATE TRIM
PUSHPIN
TEMPLATE B
MARK
DRILL
(3 mm bit 6 mm
10 mm bit)
730803AB
56. Using a hacksaw blade, cut away the license plate trim along the scribe mark made in step 54.
LICENSE
PLATE TRIM
Cut out the marked area.
MARK
MARK
UTILITY
KNIFE
PUSHPIN
MARK
14 of 16
730802BB
HACKSAW
BLADE
Cut out.
UTILITY
KNIFE
RIB
730804BB
57. Using a utility knife, cut out the rib from the license plate trim as shown.
AII 42270 (0908) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
58. Install the rear camera trim in the cutout made in the license plate trim.
61. Install four clips A, one clip B, and four nuts to the license plate trim.
DOUBLE-SIDED
TAPES
REAR CAMERA
TRIM
MARK
DOUBLE-
SIDED
TAPE
ADHESIVE
BACKING
(Remove.)
ADHESIVE
BACKING
(Remove.)
4 NUTS
LICENSE
PLATE TRIM
HOLE
730805AB
59. Using a felt-tip pen, mark the license plate trim at the ends of each double-sided tape.
DOUBLE-SIDED TAPE
(Remove.)
CLIP B
LICENSE
PLATE TRIM
4 CLIPS A
720128AY
62. Using isopropyl alcohol on a shop towel, clean the license plate trim between the marks you made.
Remove the adhesive backing from the double-sided tape, and attach the tape between the marks in the scribe line areas.
63. Fit the rear camera into the rear camera trim, and reinstall the license plate trim. Reinstall the two clips and four bolts.
REAR CAMERA
FELT-TIP
PEN
SCRIBE
LINES
LICENSE
PLATE TRIM
DOUBLE-SIDED
TAPE
MARK
751401AE
60. Remove the double-sided tape from the license plate trim. (Use 3M General Purpose Adhesive
Cleaner, 3M #08984.)
LICENSE
PLATE TRIM
HOLE
CLIPS 720129AY
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
AII 42270 (0908)
15 of 16
64. Check that all wire harnesses and cables are routed properly and that all connectors are plugged in.
65. Reinstall all removed parts.
66. Reconnect the negative cable to the battery.
67. Enter the anti-theft codes for the radio and navigation systems (if equipped), then enter the customer’s radio presets.
68. Reset the clock.
69. Check operation of the rear camera system according to the Accessory User’s Information
Manual provided with the rear camera.
16 of 16
AII 42270 (0908) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
