Op er ating In struc tions User Guide

Op er ating In struc tions User Guide
Operating Instructions
RE-1
User Guide
Table of Contents
Quick Set-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Quick Set-up: Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Quick Set-up: Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Quick Set-up: System Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
System Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Detailed Component Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
CSR-1000 Receiver Controls, Connectors and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
CSR-1000 Receiver Setup and Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
CSH-1000 Handheld Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
CSH-1000 Handheld Transmitter Setup and Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
CSB-1000 Bodypack Transmitter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
CSB-1000 Bodypack Transmitter Setup and Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
Transmitter Display Screens and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Receiver Display Screens and Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Main Operating Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Group / Channel Edit Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Frequency Edit (User Groups Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Functions Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
ClearScanTM All . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
ClearScanTM Current Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
ClearScanTM Band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Edit Microphone Label / Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Sound Check Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Set Squelch Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Copy Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Screen Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Clear Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Lockout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Master Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Transmitter On/Off Lockout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Guidelines and Recommendations for Best Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Using Multiple Wireless Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Multiple Systems and Advanced ClearScanTM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Battery Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Receiver and Antenna Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Trouble Shooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
CSR-1000 Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
CSB-1000 Beltpack Transmitter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
CSH-1000 Handheld Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
Certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
Accessories and Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
Customer Service Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
-i-
Section
1
Quick Set-Up
Quick Set-up: Receiver
5. Use the up and down arrows to change the Group number
to match the channel number displayed on the receiver.
Press SET and the Channel Number will flash.
1. Do not connect the receiver to any other equipment yet!
2. Connect the two antennas to the receiver.
3. Plug the power supply into the back of the receiver and
into an outlet
6. Use the up and down arrow buttons to change the Channel
to match the receiver. Press Set and flashing stops. The
channel is now set.
4. Press the POWER switch. Display will light up, show
information and software revision numbers for about 3
seconds and then display the main operating screen.
7. If you are using a bodypack transmitter, plug the microphone into the transmitter connector. If using a guitar,
place the Instrument/Mic switch under the battery door in
the Instrument position and plug the cord into the transmitter and guitar.
5. Press the MENU button twice to display the ClearScanTM
option screen.
6. With the CLEARSCAN ALL line indicated press SET.
7. ClearScanTM returns the clearest group. Press SET again.
Transmitter “Quick Set-up” is complete.
8. ClearScan returns the clearest channel in that group.
Press SET again.
TM
Quick set-up: System Operation
9. The display will return to the main operating screen with
the clearest channel in the clearest group assigned.
11. Set the audio mixer or other system input level to minimum.
1. With the transmitter and re ceiver on, monitor the
CSR-1000 Receiver main display screen. Note that the RF
(1-100) Bar graph should indicate near the 100 mark. The
AF Bar should show very little, if any, indication until you
talk or sing into the microphone. Adjust the transmitter
gain control if necessary to cause the AF Bar Graph to
peak near -6 to -3 but not over +3 for best performance.
12. Press the Power switch button in again.
2. Set the mixer or other system gain.
10. Turn the receiver off and connect the mixer or other audio
system to the receiver XLR Mic Level Connector or the ¼
inch Line Level Jack.
Receiver “Quick Set-up” is complete.
3. Talk or sing into the microphone or play the instrument at
a normal volume. You should hear audio coming out of the
system.
Quick set-up: Transmitter
4. If using the unbalanced 1/4" output, you may have to adjust the gain (via the control next to the connector on the
back panel) to match the level found when singing or playing with a wired connection.
1. With the Power Switch on the transmitter OFF, install a
fresh alkaline battery into the transmitter.
2. Place the transmitter Power Switch to the ON position.
"Quick Set-up" is now complete.
3. The Red Low Battery Light near the display will flash on
and then off. The display will also come on briefly, displaying battery level.
Please enjoy your RE-1 system.
4. The screen will stop at the GP (Group) and CH (Channel)
screen. Press the SET button once and the Group number
will flash.
1-1
1-2/Blank
Section
2
System Description
The CSR-1000 Wireless Microphone system combines frequency agility and ease of use like no other. The CSR-1000
transmitters and receivers operate over a 24 MHz bandwidth
in the UHF portion of the spectrum.
The high quality audio circuitry and advanced Radio Frequency (RF) signal processing offer broadcast quality signal-to-noise and audio clarity.
System Features Include:
• Advanced ClearScanTM technology for selecting clear channels and compatible groups
• 960 Radio Channels, user programmable or factory installed
• LCD Displays for ease of viewing
• Patented DSP Phase Diversity System
• USB Port for downloading software enhancements in the receiver
• Adjustable Unbalanced Line Level 1/4 inch output jack
• Fixed balanced Microphone Level XLR output jack
• Front Panel Power ON/OFF Switch
• Quadruple Tuned Ceramic Resonator front end for superior interference rejection
• SAW Filter 1st
I.F for out of band rejection
• Triple ceramic filters in 2nd
I.F for adjacent channel rejection
• Double Tuned Quadrature circuit for low audio distortion
• Permanent Flash Memory for frequency/system storage.
• Front Panel Software Control of Squelch settings
• Double Squelch (Amplitude and Tone) system prevents false squelch
• Lockout feature to prevent accidental channel changes
• Sound Check mode to speed walk testing and provide tangible results
• "Smart" battery feature in the transmitter means there is no wrong orientation
• Interchangeable heads on the handheld transmitter
• Over-molded Warmgrip™
handle on the handheld transmitter
• Cast magnesium case on the bodypack transmitter
2-1
2-2/Blank
Section
3
Detailed Component Descriptions
CSR-1000 Receiver
CSR-1000 Receiver Controls, Connectors
and Indicators
CSR-1000 UHF Receiver
menu
R
set
power
Figure 1
CSR-1000 Front Panel
7
5
Antenna
7
6
Balanced
Mic Level
Output
Antenna
R
Made in U.S.A.
FCC
CSR-1000
Tested to Comply
with FCC Standards
Unbalanced
Line Level
Output
Program
MIN
A 0001000
Patent No. 6256484
12 - 15V
AC/DC
MAX
+
-
FMR
4
8
Figure 2
CSR-1000 Back Panel
1. Power ON/OFF
5. Balanced Mic Level Audio Output
2. Graphical Display
a. Channel Display
b. Battery Strength Indicator
c. Diversity Indicator
d. RF Strength of Signal Indicator
e. Audio Level Indicator
6. Unbalanced Line Level Audio Output Connector with
Level Adjustment
7. TNC Antenna Input Connectors
8. USB Program Connector
3. Display Control Buttons (Menu/Set/Up/Down)
4. Power Connector
3-1
Receiver Setup and Operation
1. Place the receiver and antennas where there is a clear line
of sight to the area where the transmitter will be used. Rotate the antennas to separate them by 90 degrees.
a. ClearScanTM All. This program scans all of the groups
(factory and user) and returns a list of groups ranked by
the number of free channels. Once ClearScanTM All has
run, the screen will display the clearest group with the
open channels in that group. You can scroll through the
other ranked groups using UP/DOWN. When you have the
group you want, press SET to run ClearScanTM on that
group. The display will now show the group with the
Channels ranked by clearness. You can scroll through the
channels with UP/DOWN, once the desired channel is
flashing, press SET to select and the display will go to the
main display.
2. Connect the power supply cord to the receiver. Plug the
power supply into an AC outlet. Turn the receiver on and
confirm that it is ON by checking the main display screen.
The display will show the company logo, software and
channel map revision levels and then display the main
screen with the last channel set.
Caution: Please make sure the AC power supply is the correct voltage for your lo cal requirements before it is
plugged into the wall.
NOTE: Groups 7, 8, 9, and 10 have 16 channels and are
marked with an N (7N). These groups require the transmitters
to be in the NORMAL transmit power setting to work together. The N groups will always be displayed after groups
1-6 and any user defined groups no matter how many channels
are free. If you need to use more than 12 systems at one time,
scroll down to the N groups and use the clearest group with
Normal transmit power.
3. Manual Channel Change. From the main display screen
press the MENU button once. The Channel Change screen
is now displayed. Press SET: the group number should be
flashing. The Up and DOWN buttons allow you to scroll
through the 10 factory groups and 10 user definable
groups. When the group you desire is displayed, press SET
to select that group and the Channel Number will start
flashing. Scroll to the desired channel, press SET to select.
Pressing MENU anytime before pressing SET negates any
changes made since the last SET. Once the desired group
and channel are displayed (but not flashing) press MENU
twice to return to the main display screen.
b. ClearScanTM Group XX. This program will scan the
group currently selected, which is useful for multi-system
setup. With ClearScanTM All run for the first unit of a
multi-system installation, the clearest group has been selected. For each system added, leave all previously selected channel transmitters on, using Step 3 select the
current group, select ClearScanTM Group and press SET.
The display will show the group and ranked remaining
clear channels. Select the desired channel with UP/DOWN
or simply press SET for the first channel. The channel will
be selected and return to the main display. Repeat until all
systems are set up or all clear channels are full.
4. Frequency Assignment (User Defined Groups Only).
With a User Group* selected in step three, press MENU
once and the frequency assignment screen is displayed.
Press SET and the Frequency Number will flash. Use
UP/DOWN to scroll in 25 kHz steps to the desired frequency. With the desired frequency displayed press SET.
The Channel Number will be gin to flash. use the
UP/DOWN keys to select another Channel in this group
you want to assign a frequency, press SET to select and the
Frequency Number will flash. Repeat until all desired
Channels are assigned a frequency. Press MENU to stop editing. Press MENU twice to return to the main display
screen.
c. ClearScanTM Band. This program selects and ranks the
clearest 16 frequencies in the 24 MHz bandwidth regardless of groups, channels or previous coordination. This
feature is useful for selecting one clear channel in a very
dirty RF environment. From the Options screen, select
ClearScanTM Band and press SET, this scan will run until
SET is pressed again so it can be used to evaluate a site
over an hour, day or even a week. The program displays
Group 21S with the clearest open frequencies in the band
assigned channels (up to 16). These frequencies will remain assigned to this group until ClearScanTM Band is run
again.
HINT: Holding in the arrow key will increase the speed of
the scroll. Just release and press again for fine control.
* User Defined Groups start at Group #11 and display a "u"
after the group number.
Caution: Unlike the factory assigned groups, the channels
in 21S are not coordinated. If more than one channel from
group 21S is used, the combination must be walk tested
with all transmitters on before use.
5. Advanced ClearScanTM : This feature automates the process of finding a clear group of inter-modulation free
channels and the clearest channels within those groups. To
use ClearScanTM, from the main display screen push Menu
twice (or 3 times if a user defined group is being used) to
go to the Options Screen. Use the UP/DOWN keys and
SET to select the version of ClearScanTM, you wish to run.
3-2
10. Walk Test the expected area of use to check for coverage.
The SOUND CHECK screen is designed to aid this test.
From the main display screen, press MENU twice (3 times
in user groups) to display the options screen. Scroll down
to Sound Check and press set. This Sound Check Screen
will be displayed:
6. Change Lock-Out. By pressing and holding the UP and
DOWN arrow keys together for 3 seconds, the SET key is
disabled. The MENU button still allows different screens
to be displayed but no settings can be changed and
ClearScanTM will not run. To reactivate the SET key simply press and hold the UP and DOWN keys again for 3
seconds. This feature can be useful when the receiver is in
a location where unauthorized personnel have access to
the receiver.
a.
The peak hold audio meter allows you to set the
transmitter gain as high as possible for the application which maximizes the signal to noise ratio.
Sing, yell or play the instrument at the loudest desired volume and adjust the gain on the meter.
b.
The squelch break counter will tell you if you
are pushing the range or may have some interference problems to contend with. Ideally this count
would be zero for the desired performance area.
If there are several squelch breaks while walking
the area, adjust antenna placement or squelch as
in step 11 and retest. Pressing [UP] will turn on
an audible tone that will sound each time the
count is incremented. This tone can be sent to the
monitors or PA so the tester can hear when a drop
occurs and mark the lo cation on the stage.
Pressing [DOWN] turns the tone off.
c.
The high/low RF meter will tell you if you have
adequate coverage in the performance area. If the
RF level drops significantly during a walk of the
desired area, reposition the antennas, adjust the
squelch or change the channel and retest.
7. For set up, make sure the mixer or other system input used
for the CSR-1000 is muted or turned down to a minimum
level.
8. Plug an audio cable (not supplied) into the 3 pin XLR or
1/4 inch output of the CSR-1000.
a.
NOTE: The XLR connector is the preferred connection since the output is balanced and will be
more immune to noise for longer runs of cable although either can be used with good results. If the
1/4 inch connector is used, adjust the output level
on the back panel to 12 o'clock (midway in the
range) to start and adjust later if necessary.
Now refer ahead to transmitter setup and return to step 9
when that is completed.
9. With the transmitter on, speak into the microphone or play
the instrument. Turn up the level on the mixer or amplifier
until you are able to hear the desired signal. If no audio is
present, repeat setup and refer to the troubleshooting section.
CAUTION: MUTE OR TURN DOWN THE MIXER OR
AUDIO AMPLIFIERS ETC. BEFORE ADJUSTING THE
SQUELCH. OPEN (MINIMUM) SQUELCH CAN RESULT IN LOUD WHITE NOISE OVER THE AUDIO
SYSTEM.
NOTE: If the 1/4 inch output is used, it may be necessary
to adjust the receiver output until the volume level from
the wireless system approximates the level of an equivalent wired microphone/instrument.
11. Squelch Adjustment - The squelch setting can be used to
maximize range or immunity to noise. Turn the transmitter
off and from the receiver Options screen select Squelch
Adjustment and press SET. The current squelch setting
will be displayed, the setting bar will flash and "Tones
Off" will be displayed (the tone coded portion of the
squelch must be off in order to notice any changes in the
amplitude squelch setting). Adjust the squelch using the
UP/DOWN keys and walk test the unit. Maximum squelch
(all the way right) maximizes noise immunity but limits
the range. Minimum squelch (all the way left) will maximize the range but allow more noise to break through the
squelch.
3-3
Handheld Transmitter CSH-1000
1
2
3
755050
9
(ON OPPOSITE SIDE)
N
O
R
M
TRANSMIT
POWER
H
I
G
H
11
R
4
5
M
E
N
U
6
S
E
T
7
8
B
MADE IN U.S.A.
10
Figure 4
Transmitter Controls
Figure 3
Handheld Transmitter
CSH-1000 Controls, Connectors and Indicators
1.
Microphone Head - Interchangeable
2.
Main Display - LCD (Channel, Frequency or Battery Level Indication)
3.
Low Battery LED - Lights when battery is low
4.
Power On/Off Switch
5.
Menu Switch
6.
Set Switch
7.
Channel/Frequency Up Switch
8.
Channel/Frequency Down Switch
9.
Microphone Gain
10. Battery Cover - Screw type
11. Transmit RF Power Switch
3-4
Handheld Transmitter Setup
and Operation
1. Insert Battery. Remove the battery compartment cover by
unscrewing it completely. Insert a 9V battery, terminal end
first into the battery compartment.
NOTE: Operating with the transmitter audio gain set as high
as possible (without distortion or peaks all the way to the right
end of the meter) will result in the best performance and highest signal to noise ratio.
NOTE: The CSH-1000 unique design allows the battery to be
inserted and used regardless of the positive and negative terminal position.
7. Transmitting Power Adjustment (if necessary). The
CSH-1000 transmitter has two radio transmit power settings. It is factory set in the NORM position, which will
maximize the number of simultaneous users and limit interference with other wireless devices. Switching to HIGH
power will maximize range for outdoor and single user applications.
2. With battery compartment still open, turn the unit so you
can see the display and the control panel. Turn the unit on
by sliding the power switch forward to the on position.
The low battery LED will light for a second and the display will show the battery level, then the Group and Channel numbers.
8. Interchangeable Microphone Head. To remove the head,
grasp the handheld transmitter body in one hand and the
ballscreen assembly in the other. Turn the ballscreen counter clockwise and unscrew until the head is detached. See
specifications and accessories for more information on
available heads.
3. Change the group and channel numbers to match those
displayed on the receiver by pressing SET. The Group
number will flash and can be changed with the UP/DOWN
keys. Once the desired group number is showing, press
SET to select and the Channel number will flash. Select
the Channel and press SET again, the flashing will stop
and the channel is now set.
9. Test Performance. Go back to Section 3. Receiver Setup
and Operation - Step 9 to complete system set up and test.
4. Change Lock-Out. By pressing and holding the UP and
DOWN arrow keys together for 5 seconds, the SET key is
disabled. The MENU button still allows different screens to
be displayed. To reactivate the SET key, simply press and
hold the UP and DOWN keys again for 5 seconds.
5. Verify reception With the transmitter and receiver on and
matching Group and Channel, the main receiver display
should be indicating a RF signal on the bar graph. Speak
into the microphone and the Audio Meter bar graph should
indicate audio signal presence. If the level meters do not
show reception, make sure the channels are matching and
refer to the trouble shooting section.
6. Adjustment of the transmitter audio gain - If necessary
The transmitter audio gain is factory set at 1/3 of maximum range, which should be suitable for most applications. For loud or soft speakers/singers a gain adjustment
may be necessary. Have the speaker or singer use the microphone in a normal performance level voice. The Audio
Meter in the main receiver display screen should show
peaks around the -3dB level. If the meter peaks all the way
to the right or well below the -3dB level, adjust the transmitter audio gain.
To adjust the transmitter gain, gently insert the provided
screwdriver (or other 3/32 in. screwdriver) into the adjustment hole opposite the display screen. Turn lightly until
the screwdriver tip goes into the adjustment level control.
Gently turn counterclockwise until the control stops (the
microphone output is at minimum but not off). Slowly turn
the gain control up (clockwise) while speaking/singing
into the microphone and the audio meter shows peaks
around -3 dB.
3-5
5
Bodypack Transmitter
755.050
GP
CH
Voice
1
High
Menu
Inst
Tx
Normal
10
Set
Gain
9
6
Figure 6
Control View
R
4
755050
GP
CH
2
3
CSB-1000
POWER
8
OFF - ON
LOW
BATTERY
Figure 7
Top View
Figure 5
Bodypack Transmitter
CSH-1000 Controls, Connectors, and Indicators
1.
Antenna - flexible 1/4 wave antenna removable (replacement part see Section 8)
2.
Power On/Off Switch
3.
Low Battery LED Indicator
4.
TA4 Audio Connector
5.
LCD Display (Channel, Frequency or Battery Level Indication)
6.
Display Control Buttons (Menu/Set/Up/Down)
7.
Belt Clip (Removable and Detachable) not shown
8.
9V Battery Compartment
9.
Audio Gain Adjustment
10. Transmitting RF Power Switch
11. Instrument/Voice Switch
3-6
11
Bodypack Transmitter Setup
and Operation
1. Install Antenna. The CSB-1000 is equipped with a detachable antenna. Screw in the antenna included with the
system. See the accessories section at the end of this manual for in formation on op tional antennas for the
CSB-1000.
8. Adjustment of the Transmitter Audio Gain - (if necessary). The transmitter audio gain is factory set at 1/3 of
maximum range, which should be suitable for most applications. For loud or soft speakers/singers a gain adjustment may be necessary. Have the speaker or singer use the
microphone in a normal performance level voice. The Audio Meter in the main receiver display screen should show
peaks around the -3 dB level. If the meter peaks all the
way to the right or well below the -3 dB level, adjust the
transmitter audio gain.
2. Insert Battery. Pinch the battery door tabs inward and
pull the door open. Insert a 9V battery as indicated by the
+/- in the holder. (NOTE: The CSB-1000 unique design
allows the battery to be inserted and used regardless of the
positive and negative terminal position, the indicators are
there for reference only).
To adjust the transmitter gain, gently insert the provided
screwdriver (or other screwdriver) into the adjustment potentiometer. Gently turn counterclockwise until the control
stops (the microphone output is at minimum but not off).
Slowly turn the gain control up (clockwise) while speaking/singing into the microphone or playing the instrument
and the audio meter shows peaks around -3 dB.
3. With battery compartment still open, turn the unit on with
Power switch on the top panel. The low battery LED will
light for a second and the display will show the battery
level, then the Group and Channel numbers.
4. Change the group and channel numbers to match those
displayed on the receiver by pressing SET. The Group
number will flash and can be changed with the UP/DOWN
keys. Once the desired Group number is showing, press
SET to select and the Channel number will flash. Select
the Channel and press SET again, the flashing will stop
and the channel is now set.
9. Instrument Gain Adjustment. Play the instrument as
normal. Adjust the transmitter audio gain if needed. If the
audio is distorted, insure that the voice/instrument switch
is in the instrument position. Very high output instruments
may need additional cord attenuation.
NOTE: Operating with the transmitter audio gain set as
high as possible (without distortion or peaks all the way to
the right end of the meter) will result in the best performance and highest signal to noise ratio.
5. Change Lock-Out. By pressing and holding the UP and
DOWN arrow keys together for 5 seconds, the SET key is
disabled. The MENU button still allows different screens
to be displayed. To reactivate the SET key, simply press
and hold the UP and DOWN keys again for 5 seconds.
10. Trans mitting Power Ad just ment if nec es sary. The
CSB-1000 transmitter has two radio transmit power settings. It is factory set in the NORM position, which will
maximize the number of simultaneous users and limit interference with other wireless devices. Switching to HIGH
power will maximize range for outdoor and single user applications.
6. Verify reception. With the transmitter and receiver on and
matching Group and Channel, the main receiver display
should be indicating a RF signal on the bar graph. If the
level meter does not show reception, make sure the channels are matching and refer to the trouble shooting section.
7. Attach the Microphone or Instrument.
11. Test Performance. Go back to Section 3 - Receiver Setup
and Operation step 9 to complete system set up and test.
Microphone: Plug the TA4 end of the microphone cable
into the top panel of the CSB-1000. Speak into the microphone and the Audio Meter bar graph should indicate audio signal presence.
Instrument Switch the Voice/Instrument Switch to instrument. Plug in the instrument TA4 ca ble. Play the
instrument and the Audio Meter bar graph on the receiver
should indicate audio signal presence.
3-7
Displaying and Setting Transmitter Frequency:
Transmitter Display Squence:
To see the current operating frequency, press MENU at the
Group/Channel Screen.
Setting Custom Frequencies: Select a Group between 11u
and 20u and a Channel between 1 and 16 (see Group and
Channel Setting above). Press MENU to display the transmitter frequency. If this Group/Channel is blank you will see
'---.---' on the frequency display. (Blank channels also display
a '-' after the channel number on the Group/Channel screen).
Press SET and use the UP or DOWN buttons to change the
frequency. Press SET to save the new frequency, or MENU to
quit without saving changes since SET was last pressed.
Battery Gauge:
Display 3 seconds
Group Channel
Press MENU
Power Switch Disable:
When the Power Switch is disabled, you must move the power
switch to the OFF position and then press a control key
(MENU, SET, UP or DOWN) to power the unit off.
To engage a one-time power switch lock: Turn the unit on. After the display shows Group & Channel, quickly turn the
power off and on three times. "On-Loc" will show on the display. A One-time lock disables itself the next time the unit is
turned on.
Frequency Display
Press MENU
To always lock the power switch ON, press and hold SET,
then press UP. "On-Loc" will show on the display.
Battery Gauge
Press MENU
To disable Power Lock, press and hold SET, then press
DOWN. "On-Off" will show on the display. The unit can now
be turned off with just the power switch.
Firmware Revision Level:
Hold down MENU for 5 seconds. The program firmware revision number will display, followed by the factory preset frequency group revision number.
Battery Indicator:
Battery condition is displayed on power up. The low battery
LED should flash once to indicate an acceptable battery. If the
battery is nearly depleated, the low battery LED will come on
and stay on. When battery voltage is too low for proper microphone operation, the low battery LED will flash continuously
and the unit will not transmit. You can check battery condition
at any time by pressing the MENU button twice from the
Group/Channel display screen. Battery condition is also displayed at the receiver.
Quick Setup:
Press and hold the MENU button. Turn on the power switch.
Wait until Group and Channel are displayed. Release the
MENU button. Unit is now set to Group 1/Channel 1 with
Group or Channel Flashing.
Factory Reset:
WARNING: This will erase any user frequencies stored in
Groups 11u to 20u. From the Group/Channel screen, press
and hold MENU, SET, UP and DOWN until "Clr.All" is displayed on the LCD screen. Unit will restart in Quick Setup
mode.
Group and Channel Setting:
Transmitter frequencies are divided into 20 Groups of 16 frequencies (or Channels). Frequency Groups 1 through 10 are
predefined and cannot be changed. Frequency Groups 11u
through 20u can be set by the user.
To set the Group and Chan nel: Press SET at the
Group/Channel display screen. When the Group number begins to flash, use UP or DOWN to change the Group number.
Press SET to save the new Group setting. When the Channel
number begins to flash, use UP or DOWN to change the
Channel number. Press SET to save the new Channel setting.
Press MENU if you wish to stop without saving.
3-8
Section
4
Receiver Display Screens and Functions
Main Operating Screen
8
1
3
2
4
-20 -10 -6 - 3 0 +3
GP
CH
12u 05
EV
ON E
5
1 3 10 30 100
7
6
Figure 8
Main Operating Screen
Display:
1. Group Number · · · · · · · · · · · · · · · · · · · 10 factory + 10 user defined
2. Channel Number · · · · · · · · · · · · · · · · 01 to 16
3. Microphone Label or Name · · · · · · · 2 lines x 9 characters - all capitals
4. Battery Status· · · · · · · · · · · · · · · · · · · 100 to 0 Pct in 20 Pct steps / Flash if low
5. Audio Meter · · · · · · · · · · · · · · · · · · · · -30 to +3
6. RF Signal Strength· · · · · · · · · · · · · · · 0 to 300
7. Antenna Diversity Status · · · · · · · · · left or right antenna combinations
8. Edit Lockout Status · · · · · · · · · · · · · · Padlock next to GP indicates Locked
Controls:
1. [MENU] goes to next screen
2. [UP] + [DOWN] for 3 seconds Sets / Resets Edit Lockout
4-1
Group / Channel Edit Screen
E di t
MH z
B an d
B
722. 250
Ch a n n e l
16
t v
56
ch an
Gr o u p
12u
Figure 9
Group / Channel Edit Screen
Display:
1. Frequency Band Designation · · · · · · A or B
2. Group Number· · · · · · · · · · · · · · · · · · 10 factory + 10 user defined
3. Channel Number · · · · · · · · · · · · · · · · 01 - 16
4. TV Channel · · · · · · · · · · · · · · · · · · · · US TV channel the frequency is in
5. Transmit / Receive Frequency · · · · · 680.100 - 703.900 MHz A Band (US)
722.100 - 745.900 MHz B Band (US)
798.100 - 821.900 MHz D Band
841.100 - 864.900 MHz E Band
Controls:
1. [MENU] goes to next screen
2. [UP] + [DOWN] for 3 seconds Sets / Resets Edit Lockout
If Edit Mode is not locked out:
3. [SET]
A.
Starts Edit mode; Group Number begins flashing
B.
Steps between Group Number and Channel Number. Selected field flashes
to indicate it can be changed.
C.
Effects change after [UP] or [DOWN] have been pressed, then returns you
to Display Mode
4. [MENU] stops Edit mode without effecting changes since [SET] was last pressed
5. [UP] or [DOWN] (in Edit Mode)
A.
Increments or decrements Group Number when flashing
B.
Increments or decrements Channel Number when flashing
C.
[UP] and [DOWN] auto-repeat when the button is held. Auto-repeat starts
after the button has been held for 1 second. Group and Channel have a slow
auto-repeat.
4-2
Frequency Edit (User Groups Only)
E di t
B an d
MH z
B
722. 250
Ch a n n e l
16
t v
56
ch an
Gr o u p
12u
Figure 10
Frequency Edit (User Groups Only)
Display:
1. Frequency Band Designation · · · · · · A or B
2. Group Number· · · · · · · · · · · · · · · · · · 10 factory + 10 user defined
3. Channel Number · · · · · · · · · · · · · · · · 01 - 16
4. TV Channel · · · · · · · · · · · · · · · · · · · · US TV channel the frequency is in
5. Transmit / Receive Frequency · · · · · 680.100 - 703.900 MHz A Band (US)
722.100 - 745.900 MHz B Band (US)
798.100 - 821.900 MHz D Band
841.100 - 864.900 MHz E Band
Controls:
1. [MENU] goes to next screen
2. [UP] + [DOWN] for 3 seconds Sets / Resets Edit Lockout
If Edit Mode is not locked out:
3. [SET]
A.
Starts Edit mode; Frequency begins flashing
B.
Steps between frequency and channel number, selected field flashes to indicate change
C.
Effects change after [UP] or [DOWN] have been pressed, then returns you to Display Mode
4. [MENU] stops Edit mode without effecting changes since [SET] was last pressed
5. [UP] or [DOWN] (in Edit Mode)
A.
In User Defined groups, [UP] or [DOWN] increments or decrements the frequency
in 25 kHz increments
B.
Increment or decrements channel number when flashing
C.
Undefined frequencies are displayed as '---.---'.
D.
[UP] and [DOWN] auto-repeat when the button is held. Slow Auto-repeat starts after the button
has been held for 1 second. If the button is held for 16 slow steps, Auto-repeat shifts to fast
Auto-repeat.
4-3
Functions Screen
Cl e a r S c a n
Controls:
Use [UP] [DOWN] to select
and view other functions
Al l
Cl e a r S c a n
12u
Cl e a r S c a n
B an d
[ NE X T ]
Use [SET] to start the function
N a me
Ent r y
S ound
Se t
Ch e c k
Sq uel ch
[ NE X T ]
Co p y
Gr o u p
Sc r een
Cl e a r
12u
T i me r
Gr o u p
ON
12u
[ P R E V I OU S ]
Figure 11
Functions Screen
ClearScanTM All
ClearScanTM All searches all defined frequency groups for the
ones with the greatest number of receiver channels clear of interference. Once a group is selected an additional scan is made
to determine the best frequencies in the group:
Press [SET] to initiate
CL E A R S CA N
T M
Press [MENU] to abort
After scanning, ClearScanTM will display the group that has
the most interference free receive channels. These clear channels are displayed on the right half of the screen. Busy channels are represented by an X. Press [SET] to place the receiver
on this group. ClearScanTM then scans to select the clearest
channels within the group (see ClearScanTM Current Group).
Press [SET] to accept this channel and return to the operating
screen.
Gr o u p
01
05
OK ? =[ S E T ]
01
02
X
P r ev
03
X
15
NE X T
04
08
16
The [UP] and [DOWN] buttons may be used to select the next
best group/channel and so forth.
Figure 12
ClearScanTMAll
Press [MENU] to return to the Operating Screen with the receiver set to the Group, Channel and Frequency it was on
prior to executing ClearScanTM.
4-4
09
ClearScanTM Current Group
ClearScanTM Current Group scans channels within the currently selected frequency group and displays the channels that
are clear of interference.
CL E A R S CA N
T M
Press [SET] to initiate
Press [MENU] to abort
Gr o u p
After scanning the currently selected group, ClearScanTM will
display the channels that are free of interference. These clear
channels are displayed on the right half of the screen. The
channels are ranked according to noise; the channel with the
least amount of interference is presented first.
The [UP] and [DOWN] buttons may be used to select a different clear channel within the currently selected group.
12u
04
03
OK ? =[ S E T ]
15
01
P r ev
05
08
NE X T
02
16
09
Figure 13
ClearScanTM Current Group
Press [SET] to place the receiver on the currently selected
channel and return to the Operating Screen.
Press [MENU] to return to the Operating Screen with the receiver set to the Group, Channel and Frequency it was on
prior to executing ClearScanTM.
ClearScanTM Band
ClearScanTM band continuously scans all frequencies within
the bandwidth of the receiver. The scan is started at the frequency the receiver is on and proceeds in 200 kHz increments
on either side until the whole band is scanned. The scan is repeated until ended by the user.
CL E A R S CA N
S can n i n g
Press [SET] to initiate
Each frequency is scanned continuously within the band; the
highest read ing on each fre quency is stored to give a
worse-case reading as long as the scan is being done.
Ch a n .
01
Gr o u p
21s
T M
B an d
728. 475
MH z
P r ev
Pressing [SET] ends the scan. After scanning, ClearScanTM
places the 16 best frequencies in the band into 'scanned' group
21s. This group is stored to prevent accidental erasure. The
best frequency is placed at channel one and displayed.
OK ? =[ S E T ]
The [UP] and [DOWN] buttons may be used to select the next
clear channel at least 200 kHz above or below the currently
displayed frequency.
Figure 14
ClearScanTM Band
Press [SET] to accept currently selected frequency and return
to the Operating Screen.
Press [MENU] to return to the Operating Screen with the receiver set to the Group, Channel and Frequency it was on
prior to executing ClearScanTM.
4-5
Ne x t
Edit Microphone Label/Name
Display:
1. Microphone Label/Name
2. Character Set
Controls:
E nt er
A B CD E F GH I
N a me
J K L MN OP QR S
- - - - - - - - - -
T U V WX Y Z - . !
- - - - - - - - - -
0123456789
1. [MENU] goes to next screen.
2. [SET] (First time) enters Edit Mode:
A.
Figure 15
Edit Microphone Label/Name
Starts flashing first character in Name/Label
Flashes first character of the Name/Label in the
Character Set
3. [UP] flashes the next character in the Character Set and
displays the selected character at the current cursor position in the Name field.
B.
4. [DOWN] flashes the previous character in the Character
Set and displays the selected character at the current cursor
position in the Name field.
5. [SET] saves the currently selected character into the current
character position of the Name/Label field and advances to
the next character position of the Name/Label field.
6. [MENU] saves the Name/Label as displayed on the screen
and goes back to Display Mode on this screen.
Sound Check Screen
Display:
Controls:
1. Battery Status
1. [MENU] goes to next screen
2. Peak Audio level held while
screen is displayed
2. [SET] clears screen display variables
and restarts Sound Check
3. Range of RF Signal Strength
3. [UP] turns on the Count Beep (
[DOWN] turns the beep off ( ).
4. Squelch Break Counter
-20 -10 -6 - 3 0 +3
Sound
Ch e c k
),
Co u n t
00
1 3 10 30 100
Figure 16
Sound Check Screen
Set Squelch Threshold:
CAUTION: SEE PAGE 3-3 STEP 11A.
Display:
1. Press[SET]
T ON E S
Controls:
S QU E L CH
1. [SET] disables tone squelch and enables edit mode (allows
squelch level adjustment). Squelch bar will flash in edit
mode. Tone Squelch is disabled.
Figure 17
Squelch Threshold
2. [UP] raises the squelch threshold
3. [DOWN] lowers the squelch threshold
4. [SET] saves the new threshold
5. [MENU] (From edit mode) restores threshold to the setting
just after the last time [SET] was pressed
4-6
OF F
Copy Group
Selecting the Copy Group will copy the currently selected
group to the first unused User Group.
Co p y
t o
Press [SET] to accept the group and place the unit into the
Frequency Edit Screen (User Defined groups only) for editing.
Ch
Gr o u p
Gr o u p
01
12u
14u
MH z
723. 400
Press [UP/DOWN} to select a different user group.
Press [MENU] to return radio to its previous state.
Figure 18
Copy Group
Screen Timer
Selecting the Screen Timer allows enabling/disabling of
screen timer. With timer enabled the screen will return to Operating screen if no key is pressed within five minutes.
NOTE: Timer is not active in the sound check screen.
Press [UP/DOWN] to turn timer ON/OFF.
Sc r een
T i me r
ON
Press [SET] to setting.
Press [MENU] to return radio to its previous state.
Figure 19
Screen Timer
Clear Group
Clear Group will delete all channels within the selected group.
Press [SET] to clear the group, and place the unit in the
Group/Channel edit screen with Group=1, Channel=1. Group
will be flashing to enable the selection of a new group.
Press [MENU] to return radio to the operating screen.
Cl e a r
Lockout
U s e r Gr o u p ?
12u
Press and hold [UP] + [DOWN] for 3 seconds. The unit will
not allow editing of any of the user variables: Group, Channel,
Frequencies, Squelch, Name, and ClearScanTM.
Figure 20
Clear Group
Master Reset
Press and hold [Menu + Set + Up + Down] to place the unit
into its factory configuration: Group 1, channel 1, user groups
cleared, default squelch setting.
Transmitter On/Off Lock Out
There are two On/Off lock out modes available, One Time and
Everytime.
Everytime Use: With the unit on and operating in the normal
mode, press and hold [Set] and press [Up]. On-Loc will be
displayed and the power switch alone will no longer turn the
unit off. To turn the unit off, put the power switch in the off
position (On-Loc will be displayed) open the battery door and
press [Menu], [Set], [Up] or [Down] and the unit will power
down. The next time the unit is powered on the On-Loc function will still be on. To enable the power switch, press and
hold [Set] and press [Down] (On-Off will be displayed).
One Time: Cycling the power switch 3 times in under 3 seconds and On-Loc will be displayed for a second and then return to normal operation. The power switch alone will no
longer turn the unit off. To turn the unit off, put the power
switch in the off position (On-Loc will be displayed) open the
battery door and press [Menu], [Set], [Up] or [Down] and the
unit will power down. The next time the unit is powered on
the power switch will operate normally.
4-7
4-8/Blank
Section
5
Guidelines and Recommendations
for Best Performance
Compatibility
Potential Sources of Interference
The transmitter and receiver must be of the same frequency
band and set to the same group and channel in order to work
together. The CSR-1000 is available in two frequency bands,
A and B. The band in formation is available in the
Group/Channel edit screen on the receiver, the bottom label on
the handheld transmitter, and on the back panel label on the
bodypack.
There are many potential sources of interference for your
wireless system. Any electronic product that contains digital
c i r c u i tr y i n c lu d i n g d i g i t a l s i g n al p r o c e s s o r s ( r everb/multi-effects units), electronic keyboards, digital lighting
controllers, CD and DVD players, and computers, all emit RF
energy that can adversely affect the performance of your wireless system. It is always best to place the receiver as far away
as possible from these devices to minimize potential problems.
Using Multiple Wireless Systems
If two or more CSR-1000 systems and/or other UHF/VHF
wireless systems are being used in the same location, proper
frequency coordination is necessary to avoid interference. All
channels in the CSR-1000 factory set groups are designed to
work together, so if channels from just one group are used no
further coordination is required. Contact your dealer or Telex
for assistance if you are planning more systems or using the
CSR-1000 with other wireless equipment.
Analog and Digital Television stations can also interfere with
your wireless system. The CSR-1000 is designed to operate
over 24 MHz of RF bandwidth, which covers four TV channels. The factory presets on the CSR-1000 are optimized for
conditions where one or possibly two of the four stations are
covered in your area. If three of the four stations are used in
your area, it will severely limit the number of systems that will
operate together and you should be using a different band.
IMPORTANT NOTE; For 12 or less frequencies to be used
together, select all frequencies from only one of group 1-6.
Normal power will sometimes work more effectively than
high power when using larger numbers of frequencies.
Battery Recommendations
Fresh 9-volt alkaline batteries from a quality manufacturer
will yield the best performance from your CSR-1000 transmitters. Rechargeable 8.4-volt Ni-Cad batteries can be used but
will result in much shorter operation time.
IMPORTANT NOTE: Groups 7, 8, 9, and 10 have 16 channels and are marked with an N (7N). These groups require the
transmitters to be in the NORMAL transmit power setting to
work together. The N groups will always be displayed after
groups 1-6 and any user defined groups no matter how many
channels are free. If you need to use more than 12 systems at
one time, scroll down to the N groups and use the clearest
group with Normal transmit power.
When the transmitters are turned on, the red battery LED will
flash once if the battery is good. If the light does not light or
stays lit continuously, the battery is weak or dead. If the light
comes on during use, the battery is weakening and should be
replaced as soon as possible. If sound quality degrades during
use, it may be the result of a weakening battery.
Multiple Systems and Advanced
ClearScanTM
Caution: The battery level indicators, on the transmitters
and receiver displays, are based on the use of alkaline batteries. Use of other battery types will result in false readings on these indicators although the low battery LED on
the transmitters will operate normally.
Because all of the channels in the factory set groups are compatible Advanced ClearScanTM can be used to set up multiple
systems quickly and with confidence. When setting up more
than one system, set up the first system using the ClearScanTM
All function. Once the working Group has been established,
leave the first transmitter on, set the next receiver Group to the
working Group and run ClearScanTM Group. This will provide
the next clearest channel in that group. Set the transmitter to
match, leave it on and repeat until all the systems are set up. If
you run out of clear channels in one group but need to set up
more systems, contact your dealer or Telex for assistance in
choosing additional frequencies.
Receiver and Antenna Placement
Do not place the receiver near a large metal object or surface.
Locate the receiver as close as possible to the area where the
transmitter will be used. Ideally, position the receiver/antennas
within sight of the transmitter. When using multiple systems,
do not allow antennas to cross or touch each other. For best results with multiple receivers, use an AD-450 antenna splitter
(see Section 8).
5-1
5-2/Blank
Section
6
Trouble Shooting Guide
Problem
Possible Causes
Solutions
No audio and no display on the
receiver
Receiver is off
Make sure that the power supply is
properly connected and the on/off button is in the on position
No audio and no RF signal indicator
on the receiver display
Transmitter is off
Turn on transmitter power switch
Transmitter is on a different channel
Match the transmitter group and channel to the one displayed on the receiver.
No (or dead) battery in transmitter
Insert fresh battery in transmitter
Faulty battery contacts
Clean and or bend contact
Microphone not connected
Check the TA4F con nector on the
bodypack or the detachable microphone el e ment con nec tion on the
handheld
Low gain setting on the transmitter
Increase the transmitter gain
Receiver audio output cable is damaged or disconnected
Connect, repair or replace cable
Gain not sufficient on
mixer/preamp/amp input or it is muted
Increase gain on mixer or un-mute
the input
Receiver output too low (1/4" output)
Increase the audio output setting
Transmitter audio gain too high
Decrease the transmitter gain setting
Receiver output too high (1/4" output)
Decrease the receiver output setting
Loud instrument or audio source
Change the bodypack au dio mode
switch to Instrument setting
Battery level low in transmitter
Insert fresh battery in transmitter
Another CSR-1000 system in the installation is on the same channel or the
signals are mixing
Make sure all the channels in use are
from the same group. Use ClearScanTM
to select the clearest group. If more
channels are needed call Telex at
800-392-3497 for coordination help
Another wireless product in the area is
on the same frequency or the signals
are mixing
Use ClearScanTM to change the operating frequency. If problems persist, call
Telex at 800-392-3497 for coordination
help
No Audio with good RF signal indicator but no (or low) Audio indicator on
the receiver display
No (or low) Audio with good RF signal and Audio indicators on receiver
display
Distorted audio signal
Interference
6-1
Trouble Shooting Guide (continued)
Possible Causes
Solutions
Receiver is too close to digital signal
processor or similar device
Move the receiver to a different
location
Strong elec tro mag netic field from
stage lighting or other source near the
transmitter or receiver, which may be
producing RF noise at or near the operating frequency
Use ClearScanTM to change the operating frequency. Repair or remove the
source of interference. Move the receiver to a different location.
RF reflective metal obstacles between
the transmitter and receiver
Move the obstacles, or reposition the
receiver/antennas
Poorly oriented beltpack antenna
Check the antenna connection and reorient the bodypack so the antenna is
vertical (up and down) and facing the
receiver, if possible.
Faulty receiving antenna system
Check all antenna connections and reposition to be in line-or-sight with the
transmitter
Application requires high transmitter
output
Switch the transmitter to the high
power setting (see page 3-6)
Can't change settings on receiver or
transmitter
Lockout feature is enabled
Disable lockout (see pages 3-3, 3-5,
and 3-7)
Can't change frequency setting for a
channel
Channel not in a user definable group
Change to a user definable group
(see page 3-2)
Bodypack or Handheld transmitter
will not turn off, display says On-Loc
On/Off lockout is engaged
Put the on/off switch in the off position
and press one of the programming buttons (see page 4-7)
Problem
Interference (continued)
Short range or drop-outs
6-2
Section
7
Technical Specifications
CSR-1000 Receiver
Specifications
Overall
Receiver Type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Synthesized PLL
Frequency Range (RF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A Band 680 - 704 MHz
B Band 722 - 746 MHz
D Band 798 - 822 MHz
E Band 841 - 865 MHz
Number of Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >900 possible channels
Programmable in 25 kHz steps
Modulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +/- 40 kHz deviation
Diversity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DSP Posi -PhaseTM True Diversity
RF Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <0.8 μV for 12 dB SINAD
Image Rejection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >60 dB
Squelch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tone plus Amplitude
Ultimate Quieting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . > 100 dB
Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 VAC, 750mA max
Operating Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -7° to 49° C (20° to 120° F)
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.72 in. H x 7.50 in. W x 8.38 in. D
43.69 mm H x 190.50 mm W x 212.85 mm D
7-1
CSR-1000 Receiver
Specifications (continued)
Audio Parameters
Frequency Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 - 15 kHz +/- 2dB
Balanced Output. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -20 dBV (max @ 40 kHz deviation)
Unbalanced Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . adjustable 8 mV to 0.755V RMS
Distortion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <0.5% (ref 1kHz, 40kHz deviation)
Signal-to-Noise Ratio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >110 dB
Dynamic Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >100 dB
Transmitters CSB-1000 and CSH-1000
RF Output. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Normal 5 mW Typical
High 50 mW Typical
Microphone Head RC767A. . . . . . . . . . . . . . ElectroVoice N/D 767a cardioid N/DYM dynamic
Microphone Head RC510 . . . . . . . . . . . . . . . . . . . . . . . ElectroVoice RE 510 cardioid condenser
Standard Lavalier Microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Telex ELM-22 MicroMiniTM
Omni-Directional Condenser
TA4F Connector Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pin 1: Ground; Pin 2 Mic Input;
Pin 3: +5V bias; Pin 4: +5V bias
through a 3kW resistor
Audio Gain Adjustment Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Handheld 26 dB
Bodypack 40 dB
Power Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Volt Alkaline Battery
Battery Life (Typical) . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10 hours with 9-Volt Alkaline Typical
Bodypack Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Detachable 1/4 wave
Handheld Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internal 1/2 wave
Dimensions (Handheld) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.54 in. Long
26.8 cm Long
Dimensions (bodypack) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.8 in. H x 2.38 in. W x 0.92 in. D
96.5 mm H x 60.5 mm W x 23.4 mm D
7-2
FCC INFORMATION
The TELEX Receiver CSR-1000 is authorized under Part 15 of the Federal Communication Commission.
The Telex CSB-1000 and CSH-1000 Transmitters are type Accepted under United States
Federal Communications Commission Part 74.
Licensing of Telex equipment is the user’s responsibility and licensability depends
upon the user’s classification, user’s application, and frequency selected. Telex
strongly urges the user to contact the appropriate telecommunications authority for
any desired clarification.
CAUTION: Any changes or modifications made to the above equipment could void the
user’s authority to operate the equipment.
7-3
7-4/Blank
Section
8
Accessories and Parts
1/4 Wave Rx Antenna (A/B)
MODEL No.
Order No.
ANU-14
879010
1/4 Wave Rx Antenna (D/E)
879010-1
1/2 Wave Rx An tenna (A)
CLA-5 (Green)
870658-5
1/2 Wave Rx Antenna (B)
CLA-6 (Orange)
870658-6
1/2 Wave Rx Antenna (D + E)
CLA-8 (Purple)
870658-8
1/2 Wave Antenna Bracket
AB-2
71138000
Antenna/Power Distribution (A, B, D, E)
APD4
APD4 (A + B Band)
APD4-1 UK (E Band)
APD4-1 EUR (D Band)
Termination Plug for APD4
TP-2
650095
LPA-500 (450-900 MHz)
LPA 500
CXU-25
71151025
CXU-50
71151050
CXU-75
71151075
CXU-100
71151100
AN-Flex A (Green)
879220-4
AN-Flex B + D (RED)
879220-5
1/4 Wave Bodypack TX Antenna (E)
AN-Flex E (Blue)
879220-6
1/4 Wave Super-Flex Tx Antenna (A)
AN-Sflex A (Green)
879538-4
AN-Sflex B + D (Red)
879538-5
AN-S flex E Blue
879538-6
WP-1000
879553
SCB-1
640156
Guitar Cord
MAC-G2
879526
767a Dynamic Head for CSH-1000
RC767A
71837000
RC510
71839000
Directional Rx Antenna (A, B, D, E)
Coaxial Antenna Cable
1/4 Wave Bodypack Tx Antenna (A)
1/4 Wave Bodypack Tx Antenna (B + D)
1/4 Wave Super-Flex Tx Antenna (B + D)
1/4 Wave Super-Flex Tx Antenna (E)
Bodypack Pouch
Strip Connector Mating Block
RE510 Condenser Head for CSH-1000
8-1
8-2/Blank
Section
9
Customer Service
CUSTOMER SERVICE INFORMATION
If your receiver or transmitter should need servicing under the warranty, please contact:
North America
Customer Service Department
TELEX COMMUNICATIONS, INC.
8601 East Cornhusker Highway,
Lincoln, Nebraska 68507-9702 U.S.A.
Phone: (402) 467-5321
Technical Assistance: 800-392-3497
(U.S. and Canada only)
Europe
Telex EVI Audio GmBH
Hirschberger Ring 45
D-94315 Straubing
Germany
Tel: +49 (0) 9421 706 0
Fax: +49 (0) 9421 706 350
All claims of defect or shortage should be sent to the above address. When returning
items for service, you must provide date and proof of purchase, such as a copy of the
sales receipt, to establish warranty. A letter should be included outlining all symptoms
and claimed defects. Information on how the equipment was installed and used is very
helpful. Please include your phone number and return address in case our service technicians need to contact you.
Units that have been modified cannot be accepted for repair.
Include all information requested by the Service Department. Then pack the unit as follows:
Check the unit to see that all parts and screws are in place. Then wrap it in heavy paper
or put it in a plastic bag. If the original carton is not available, place the unit in a strong
carton that is at least six inches bigger in all three dimensions than the unit. Fill the
carton equally around the unit with resilient packing material (shredded paper, foam,
etc.). Seal it with gummed paper tape, tie it with a strong cord, and ship it by prepaid
express, United Parcel Service or insured parcel post to the Telex Service Department.
It is very important that the shipment be well-packed and fully insured. Damage claims
must be settled between you and the carrier and this can delay repair and return of the
unit to you.
Telex reserves the right to make changes in design and improvement on its product
without assuming any obligation to install the same on any of its products previously
manufactured. Further Telex reserves the right to ship new and/or improved products
which are similar to the form, fit and function of products originally ordered.
For other office locations see www.electrovoice.com
9-1
9-2/Blank
Section
10
Limited Warranty
Limited Warranty
TELEX Communications, Inc. (”Telex”) warrants to the user, who originally purchased the serialized
product delivered with this card, that the product will be free from defects in material and workmanship for the following periods after such date of purchase. Material 36 months, workmanship 36
months. Microphones, earphones, neckloops, cables & connectors are warranted for ninety days. Telex
will, at its option, repair or replace free of charge such defective products subject to the following conditions:
1. Delivery of the product or parts postage prepaid to the Telex/EV dealer, authorized service facility or factory.
2. Determination by Telex that a defect exists and is covered by limited warranty. Defects due to alteration, repair by unauthorized persons, insertion of non-Telex parts, misuse, accidental damage, use of
the equipment for purposes other than those for which it was designed, and the like, are not covered
by this limited warranty and repairs thereof will be subject to normal service charges.
3. Repairs and replacement parts are covered under this limited warranty only for the unexpired term of
the original limited warranty.
4. Products purchased from unauthorized dealers are not warranted.
5. You must fill out and return the product warranty card to register the purchase date of serialized
items. A copy of the bill of sale showing the date of purchase must accompany all warranty work.
THIS LIMITED WARRANTY IS EXPRESSLY IN LIEU OF ANY EXPRESS OR IMPLIED WARRANTY, INCLUDING ANY IMPLIED WARRANTY OR MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE WHICH EXTENDS BEYOND THE TERM HEREOF. THE
REMEDIES PROVIDED BY THIS LIMITED WARRANTY ARE THE ONLY REMEDIES AVAILABLE TO ANY PERSON. NO PERSON HAS ANY AUTHORITY TO BIND TELEX TO ANY
REPRESENTATION OR WARRANTY OTHER THAN THOSE PROVIDED BY THIS LIMITED
WARRANTY. TELEX SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY FAILURE OR OTHERWISE OF THE PRODUCT.
Some states do not allow exclusions or limitations of incidental or consequential damages or limitations on how long an implied warranty lasts, so the limitations or exclusions herein may not apply to
you. This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state and country to country.
10-1
10-2/Blank
TELEX COMMUNICATIONS, INC. • 12000 Portland Ave. South, Burnsville, MN 55337.
PN 803333 Rev A
June 2004
Made in U.S.A.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement