advertisement
2 / 4 / 8 / 16 /24 port VoIP Gateway
User’s Manual
Table of Contents
1.4.3
R
EAR
P
ANEL
D
ESCRIPTIONS
¡E
RROR
!
M
ARCADOR NO DEFINIDO
.
2
ERIES MODULE EXTENSION INSTALL
3
PREFACES
0.1 About This Manual
This manual is designed to assist users in using VoIP Gateway. Information in this document has been carefully checked for accuracy; however, no guarantee is given as to the correctness of the contents. The information contained in this document is subject to change without notice.
0.2 Copyright Declarations
Copyright 2008 IP-Telephony Network Inc. All rights reserved. This publication contains information that is protected by copyright. No part may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language without written permission from the copyright holders.
0.3 Trademarks
Products and Corporate names appearing in this manual may or not be registered trade marks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without to infringe.
0.4 Safety Instructions
The most careful attention has been devoted to quality standards in the manufacture of the
Gateway. Safety is a major factor in the design of every set. But, safety is your responsibility too.
Use only the required power voltage. Power Input: AC 100-240V, 50-60Hz
To reduce the risk of electric shock, do not disassemble this product. Opening
or removing covers may expose the Gateway to hazardous voltages. Incorrect reassembly can cause electric shock when this product is subsequently used.
Never push objects of any kind into the equipment through housing slots since
they may touch hazardous voltage points or short out parts those could result in a risk of electric shock. Never spill liquid of any kind on the product. If liquid is spilled, please refer to the proper service personnel.
Use only Unshielded Twisted Pair (UTP) Category 5 Ethernet cable to RJ-45
port of the Gateway.
0.5 Warranty
We warrant to the original end user (purchaser) that the S series gateways will be free from any defects in workmanship or materials for a period of one (1) years from the date of purchase from the dealer. Please keep your purchase receipt in a safe place as it serves as proof of date of purchase. During the warranty period, and upon proof of purchase, should the product have indications of failure due to faulty workmanship and/or materials, we will, at our discretion, repair or replace the defective products or components, without charge for either parts or labor, to whatever extent we deem necessary to re-store the product to proper operating condition. Any replacement will consist of a new or re-manufactured functionally equivalent product of equal value, and will be offered solely at our discretion. This warranty will not apply if the product is modified, misused, tampered with, damaged by an act of God, or subjected to abnormal working conditions. The warranty does not cover the bundled or licensed software of other vendors.
Defects which do not significantly affect the usability of the product will not be covered by the warranty. We reserve the right to revise the manual and online documentation and to make
4
changes from time to time in the contents hereof without obligation to notify any person of such revision or changes.
Note
Repair or replacement, as provided under this warranty, is the exclusive remedy of the purchaser. This warranty is in lieu of all other warranties, express or implied, including any implied warranty of merchantability or fitness for a particular use or purpose. We shall in no event be held liable for indirect or consequential damages of any kind of character to the purchaser.
To obtain the services of this warranty, contact us for your Return Material Authorization number (RMA). Products must be returned Postage Prepaid. It is recommended that the unit be insured when shipped. Any returned products without proof of purchase or those with an out-dated warranty will be repaired or replaced and the customer will be billed for parts and labor. All repaired or replaced products will be shipped by us to the corresponding return address, Postage Paid. This warranty gives you specific legal rights, and you may also have other rights that vary from country to country.
Introduce
2 port / 4 port / 8 port / 16 port / 24 port
series VoIP Gateway provides the lower to higher
VoIP ports total Solutions. This document describes the usage of Voice gateway.
1.1 Overview
VoIP Gateway which is a device that allows one to connect a normal PSTN telephone to the
Internet in order to make or place telephone calls.
VoIP Gateway device may work in conjunction with a computer, such as an IP-sharing /
Router, or it may be a stand-alone device that communicates with a service provider over the
Internet.
VoIP Gateway provides a direct analog interface for computer modems, fax machines, analog telephones, and other devices that require an analog port.
2/4/8 port Series VoIP Gateway can build in a simple H.323 Gatekeeper or SIP Proxy Server.
VoIP Gateway also support standard Internet services, such as IP-Sharing, NAT, Virtual
Server, DDNS, QOS, Port Filter, IP Filter function.
1.2 Acronyms Table
Acronym: Full Name:
ADC
DAC
DSP
Analog to Digital Converter
Digital to Analog Converter
Digital Signal Processor
FXS
DDNS
DMZ
DTMF
IP
GMT
MII
NTP
Foreign Exchange Subscribe
Dynamic Domain Name System
Demilitarized Zone
Dual Tone Multi Frequency
Internet Protocol
Greenwich Mean Time
Network Time Protocol
Media Independent Interface
Acronym: Full Name:
CODEC Coder / Decoder
DC
PSTN
FXO
DHCP
Direct Current
Public Switch Telephone Network
DNS Domain Name System
PPPOE Point-to-Point Protocol over
ToS
LAN
MAC
NAT
DAA
Foreign Exchange Office
Dynamic Host Configuration
Protocol
Ethernet
Type of Service
Local Area Network
Media Access Control
Network Address Translation
Direct Access Arrangement
5
RTP Real-Time Transport Protocol
SIP
STUN
TCP
Session Initiation Protocol
Simple Traversal of UDP through
NATs
Transmission Control Protocol
MWI Message Waiting Indicator
1.3 Introduction
RTCP
SLIC
URI
UDP
VoIP
Real-Time Transport Control
Protocol (also known as RTP control protocol)
Subscriber Line Interface Circuit
Uniform Resource Identifier
User Datagram Protocol
Voice Over Internet Protocol
This VoIP Gateway provides a total solution for integrating voice-data network and PSTN.
The 2 port / 4 port / 8 port / 16 port / 24 port series
gateway is low to high density port gateways which both support SIP / H.323 VoIP Protocol. The 2 port / 4 port / 8 port / 16 port /
24 port Gateway series
gateway allows 2 ~ 24 lines (model option) analog voice and fax communication over a traditional data communications/data networking digital Internet. Here are all models Gateway compare table follow.
Model Compare Table
Model
FXO Port FXS Port LAN Port WAN Port
LCD
Display
RS-232 port
SIP H.323
24 port Series ( 24 analog lines)
24 FXS
0 24
12 FXS+
12FXO
24 FXO
12
24
12
0
1
1
1
1
1
1
√
√
√
√
√
√
√
√
√
√
√
√
1U/19 inch Chassis
16 port Series ( 16 analog lines )
16 FXS
0 16
8 FXS
+8FXO
16 FXO
8
16
8
0
8 port Series ( 8 analog lines )
0 8
8 FXS
4 FXS + 4
FXO
4 4
8 FXO
8 0
0
1
4
3
1
1
1
8 port Series( 8 analog lines Gateways)
8 FXS
0 8 1
6 FXS + 2
FXO
4 FXS +4
FXO
8 FXO
2
4
8
6
4
0
1
1
1
4 port Series ( 4 analog lines Gateways)
4 FXS
3 FXS + 1
FXO
2 FXS + 2
FXO
4 FXO
2
4
2
0
4
4
4
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
1U/19 inch Chassis
1U/19 inch Chassis
6
2 port Series ( 2 analog lines gateways)
2 FXS
1 FXS + 1
FXO
2 FXO
0
1
2
1
4
4
1
1
2 0 4 1
1.4 Front Panel LED Indicators & Rear Panels
1.4.1 Gateway Outlook
√
√
√
2 port / 4 port gateway Series:
√
√
√
8 port gateway Series
16 port / 24 port gateway Series
(1U/19 inch Chassis)
1.4.2 Front Panel LED and Container Descriptions
2 port / 4 port Gateway Series
------------------------------------------------------------------------------------
LED State Description
------------------------------------------------------------------------------------
1. POWER On
Off
GW is power ON
GW is power Off
-------------------------------------------------------------------------------------
7
2. WAN port On GW network connection established
Flashing Data traffic on cable network
Off Waiting for network connection
-------------------------------------------------------------------------------------
3. LAN port On LAN is connected successfully
Flashing Data is transmitting
Off Ethernet not connected to PC
-------------------------------------------------------------------------------------
4. FXS(Port) Off Telephone Set is On-Hook
Flashing Ring Indication
On
5. FXO(Port) Off is
Line is On-Hook
Off-Hook
-------------------------------------------------------------------------------------
On Line is Off-Hook
NOTE
: System initialization will turn some LEDs ON for a few sec.
When System is Boot/Reboot, the Port LEDs will flash in turn for a few sec.
8 port gateway Series
------------------------------------------------------------------------------------------
LED State Description
------------------------------------------------------------------------------------------
1. POWER On
Off
GW is power ON
GW is power Off
------------------------------------------------------------------------------------------
2. RUN port On GW connection established
Flashing Data traffic on cable network
Off
3. WAN port 100M
Waiting for GW connection
------------------------------------------------------------------------------------------
On GW network connection 100MB network
Off GW network connection 10MB network
ACT
ON GW network connection established
Flashing Data traffic on cable network
Off
4. LAN port
100M
Waiting for network connection
------------------------------------------------------------------------------------------
On GW LAN connection 100MB network
Off GW LAN connection 10MB network
ACT
On LAN is connected successfully
Flashing Data is transmitting
Off
-------------------------------------------------------------------------------------
5. FXS(Port) Off
Ethernet not connected to PC
Telephone Set is On-Hook
Flashing Ring Indication
8
Telephone Off-Hook
-------------------------------------------------------------------------------------
6. FXO(Port) Off
On
-------------------------------------------------------------------------------------
7. RES Button Push
Line is On-hook
Line is Off-hook
Push Button until 5 second
Set
-------------------------------------------------------------------------------------
8. RS-232 Console port connect to PC
NOTE
: System initialization will turn some LEDs ON for a few sec.
When System is Boot/Reboot, the Port LEDs will flash in turn for a few sec.
8 port / 16 port / 24 port gateway Series Gateway
(1U/19 inch Chassis)
------------------------------------------------------------------------------------------
LED State Description
------------------------------------------------------------------------------------------
1. POWER On
Off
GW is power ON
GW is power Off
------------------------------------------------------------------------------------------
2. RUN port On GW connection established
Flashing Data traffic on cable network
Off
3. WAN port 100M
Waiting for GW connection
------------------------------------------------------------------------------------------
On GW network connection 100MB network
Off GW network connection 10MB network
ACT
ON GW network connection established
Flashing Data traffic on cable network
Off
4. LAN port
100M
Waiting for network connection
------------------------------------------------------------------------------------------
On GW LAN connection 100MB network
Off GW LAN connection 10MB network
ACT
On LAN is connected successfully
Flashing Data is transmitting
Off
-------------------------------------------------------------------------------------
5. FXS(Port) Off
Ethernet not connected to PC
Telephone Set is On-Hook
Flashing Ring Indication
On
6. FXO(Port) Off is
Line is On-hook
Off-Hook
-------------------------------------------------------------------------------------
On Line is Off-hook
-------------------------------------------------------------------------------------
6. LCD Panel Off System is Shutdown
9
On System is Up
NOTE
: System initialization will turn some LEDs ON for a few sec.
When System is Boot/Reboot, the Port LEDs will flash in turn for a few sec.
2 port / 4 port VoIP Gatway Series
Item Port
1
Description
FXS(Foreign Exchange Station) Connect to Phone with RJ-11 (Black) analog line.
FXS port was connected to your telephone sets, FAX, or Trunk Line of PBX.
2
3
FXO(Foreign Exchange Office) Connect to PBX or CO line with RJ-11(Gray) analog line. FXO port was connected to the extension port of a PBX or directly connected to a PSTN line of carrier.
WAN(Wide Area Network) Connect to the network with an Ethernet cable. This
4 LAN(Local Area Network) port allows your GW to be connected to an Internet
Access device, e.g. router, cable modem, ADSL modem, through a networking cable with RJ-45 connectors used on 10BaseT and 100BaseTX networks.
Connect to PC with Ethernet cable. 4 ports allow your
PC or Switch/Hub to be connected to the GW through a networking cable with RJ-45 connectors used on
10BaseT and 100BaseTX networks.
5
6
RES(Reset button)
AC power(DC in 12V)
The reset button, when pressed, resets the cable voice gateway without the need to unplug the power cord.
Push this button until 5 seconds, and GW will be set to factory default.
A power supply cable is inserted.
The supplied power adapter converts
110V or 220V AC to DC as required for this device.
10
8 port gateway Series
Item Port
1 FXS(Foreign Exchange Station)
(Black Color)
2
3
4
5.
6
7
FXO(Foreign Exchange Office)
(Gray Color)
WAN(Wide Area Network)
LAN(Local Area Network)
Switch power
AC power(DC in 12V)
RS-232
Description
Connect to Phone with RJ-11 analog line. FXS port was connected to your telephone sets, FAX, or Trunk
Line of PBX.
Connect to PBX or CO line with RJ-11 analog line.
FXO port was connected to the extension port of a
PBX or directly connected to a PSTN line of carrier.
Connect to the network with an Ethernet cable. This port allows your GW to be connected to an Internet
Access device, e.g. router, cable modem, ADSL modem, through a networking cable with RJ-45 connectors used on 10BaseT and 100BaseTX networks.
Connect to PC with Ethernet cable. 1 port allow your
PC or Switch/Hub to be connected to the GW through a networking cable with RJ-45 connectors used on
10BaseT and 100BaseTX networks.
Power Switch, turn on/off the GW power supplied. [I] is turn on the power, and [o] is turn off the power.
A power supply cable is inserted.
The supplied power adapter converts
110V or 220V AC to DC as required for this device.
RS-232 console port connect to PC, Use Pc com port to connect RS-232 console , setting GW configure.
11
8 RES(Reset button)
*there is no FXO port in Call Manager
The reset button, when pressed, resets the cable voice gateway without the need to unplug the power cord.
Push this button until 5 seconds, and GW will be set to factory default.
16 port / 24 port Series Gateway
(1U/19 inch Chassis)
Item Port
1 Standard Telco 50 PIN
Connector (RJ-21)
2 RES(Reset button)
3 RS-232
4 WAN(Wide Area Network)
5. LAN(Local Area Network)
6 Switch power
Description
It is a 50 pins RJ-21 connector for connecting to telephone patch pane
The reset button, when pressed, resets the cable voice gateway without the need to unplug the power cord.
Push this button until 5 seconds, and GW will be set to factory default.
RS-232 console port connect to PC, Use Pc com port to connect RS-232 console , setting GW configure.
Connect to the network with an Ethernet cable. This port allows your GW to be connected to an Internet
Access device, e.g. router, cable modem, ADSL modem, through a networking cable with RJ-45 connectors used on 10BaseT and 100BaseTX networks.
Connect to PC with Ethernet cable. 1 port allow your
PC or Switch/Hub to be connected to the GW through a networking cable with RJ-45 connectors used on
10BaseT and 100BaseTX networks.
Power Switch, turn on/off the GW power supplied. [I]
12
7
8
AC power(DC in 12V)
LCD Panel is turn on the power, and [o] is turn off the power.
A power supply cable is inserted.
The supplied power adapter converts
110V or 220V AC to DC as required for this device.
Setting GW and view GW status, use [up/down] button to select Menu, and [menu] button return to main and click select.
1.5 Features and Specifications
The 2 port / 4 port / 8 port / 16 port / 24 port Series Gateways provide software features to provide a convenient comprehensive solution for your VoIP network
1.5.1 Gateway Features
VoIP Key Features
Both support SIP and H.323 protocols: SIP Registration and Digest Authentication and
H.323 Gatekeeper Registration.
Single Number / Account for multiple ports.
Caller ID Delivery: FXS support DTMF Caller ID generation.
Smart VoIP call Dialing Book: VoIP call Book could provide any application VoIP call to any type destination (Domain name / IP address, PSTN or PBX) or hunting number setting.
AC termination Impedance : 600/900 OHM and complex impedance
Answer Supervision for Polarity Reversal Detection and Voice detection
NAT traversal: This feature allow gateway to operate behind any NAT/Firewall device. There is no need to change any configuration of NAT/Firewall like setting virtual server.
Smart-QoS: This feature provides good voice quality when user place a VoIP call and access internet at the same time. The gateway will automatically start to reserve bandwidth for voice traffic when VoIP call proceeds.
Call Hunting Facility: This function helps gateway to use the lines effectively. This facility automatically transfers your incoming call to a free line. Subscribers need not indicate numerous numbers of each port of gateway.
Voice channels status display: This function display each port status like as on-hook, off-hook, calling number callee’s number, talk duration, codec.
Pulse Dial support: Support pulse dialing generation and detection. (Optional)
Flash Detection and Generation Program: FXO support Flash Generation and FXS support
Flash Detection.
CDR: Use Syslog Server to receive CDR information that gateway send by UDP.
FXO answer Mode: FXO provides Ringing Answer, Connection Answer and Non Answer for configuration.
FXO anti-seized mechanism : FXO provides busy tone auto-learning and manually configuration busy tone learning
Modules Card Extension: Extension FXO/FXO Modules card upgrade gateway port max to 24 port.( 16 port / 24 port gateway series
[1U/19 inch Chassis]
)
Call Features
Voice channels status display
Direct Dialing Mode : peer to peer call (support IP Address Call or Domain Name Call)
Register Call Mode : register to SIP Proxy Server or H.323 Gatekeeper
Adjustable volume : - 9 db ~ 9 db
Compression(VAD)
Auto Dial for speed
Dynamic Jitter Buffer
13
Configuration & Management
Web-based Graphical User Interface
RS232 for configuration(8 port / 16 port / 24 port series only)
Remote management over the IP Network
FTP firmware upgrade
Backup and Restore Configuration file
Front LCD Panel for System Status and Management(16 port / 24 port series only) support
Auto-provision by FTP method (Optional)
1.5.4 Gateway Specifications
2 port / 4 port / 8 port gateway Series Gateway
Telephony Specification:
Voice Codec:
FAX support :
Echo Cancellation:
G.711(A-law /
μ -
law), G.729 AB,
G.723 (6.3 Kbps / 5.3Kbps).
T.30 / T.38.
G.165/G168(Version:2000).
FXO Caller ID detection :
FXO hang up detection / anti-seized :
Answer supervision:
FXO answer delay time:
DTMF and FSK
(need optional Caller ID module only).
Tone Learning Automatically / Manual Tone
Learning
Support Battery Reverse Detection and Voice
Detection.
Support delay 0 – 8000 ms to answer.
Adjustable AC Termination Impedance : 600 / 900 OHM and complex Impedance.
Failsafe Mechanism (FXS relay to FXO) : Power failed by pass support / Internet Failed by pass (Optional)).
Pulse Metering: 12K Hz and 16K Hz Metering (Customized)
IP Specification:
Protocol:
LAN :
WAN:
Network Address Translation:
Smart QoS:
TOS:
General Specification
AC power :
Temperature:
Humidity:
Emission:
H.323 v2/v3/v4 and SIP (RFC 3261) ,
SDP (RFC 2327), Symmetric RTP,
STUN (RFC3489), ENUM (RFC 2916),
RTP Payload for DTMF Digits (RFC2833),
Outbound Proxy Support.
Support Virtual Server, DHCP Server.
Support PPPoE client, DHCP client, Fix IP Address,
DDNS client.
Providing build-in NAT router function.
Guarantee the voice bandwidth
IP TOS (IP Precedence) / DiffServ
AC100V-240V, DC12V/1.5A,50/60 Hz
0°C ~ 40°C (Operation) up to 90% non-condensing
FCC Part 15 Class B, CE Mark
14
Dimension :
Weight:
Others:
IU-440 x 250 x 45 mm(16 port / 24 port)
260 x 130 x 35 mm(8 port)
260 x 130 x 35 mm(2 port / 4 port)
5200 g(16 port / 24 port)
1500g (Aluminum)(8 port)
1100g (Aluminum )(2 port / 4 port)
Standard 50 pin RJ-21 Telco connectors
(16 port / 24 port)
16 port / 24 port Series
gateway can be extension. Combination different modules card, you can change/upgrade your gateway FXS/FXO ports. Max Up to 24 ports.
Modules Card Table [16 port / 24 port (
1U/19 inch Chassis
) Only]
Mother Board Description and Function
8 FXS motherboard
Mother Board with 8 FXS Interface
4 FXS + 4 FXO
Mother Board with 4 FXS + 4 FXO Interface
motherboard
8 FXO motherboard
Mother Board with 8 FXO Interface
Modules Card
8 FXS module
4 FXS + 4 FXO module
8 FXO module
Description and Function
8 FXS Interface Module
4 FXS + 4 FXO Interface Module
8 FXO Interface Module
Installation and Setup
2.1 Package Content
Please check enclosed product and its accessories before installation. (Refer to the item number). These contents are from pre-released product. The contents for the final product might change a little bit.
Appurtenances:
15
5
6
3
4
Item Appurtenances
1
2
CD-ROM
RJ-45 cable
7
Description
CD Include in all product user manual and datasheet.
Internet cable RJ-45 connect to NIC/Gateway/Router
RS-232 cable
Power supply & cable(8)
RS - 232 Console port connect to PC COM port.
Power Supply,input:100-240V output:+12V
(Europe/UK/US)
Power Supply cable. Power cable(16/24)
Power supply & cable(2/4) Power Supply,input:100-240V output:+12V
(Europe/UK/US)
25 port Telephone For 16/24 port telephone interface Patch Panel .
Patch Panel and Cable
(Optional).
2.1.1 2 port /4 port Series Gateway
16
The 2 port / 4 port Series packet contents:
2 port / 4 port gateway Series
RJ-45
AC Power Adapter
CD-Rom(User manual)
2.1.2 8 port Series Gateway
X1
X1
X1
X1
The 8 Port packet contents:
8 port Series
RJ-45
RS-232
AC Power Adapter
CD-Rom(User manual)
X1
X1
X1
X1
X1
17
2.1.3 16 port / 24 port Series High Density Gateway
Patch Panel:
The 16 port / 24 port Series Port packet contents: (
Note : 1U/19 inch Chassis
)
Gateway (16 port /24 port
Series)
RJ-45
RS-232
AC Power Cable
CD-Rom(User manual)
Patch Panel(Option)
X1
X1
X1
X1
X1
X1
2.2 Installation
Install Gateway
1 Connect the 12V DC IN to the power outlet with power adaptor.
2 Connect FXO to PSTN / PBX Extension Line.
3 Connect FXS to a telephone jack with the RJ-11 analog cable (Phone / PBX Trunk Line.)
Connecting to a PC:
1 Connect the Ethernet cable (with RJ-45 connector) to any LAN port.
2 Connect the other end of the Ethernet cable to your PC’s installed network interface card (NIC).
3 The LED indicators at both the Ethernet port and the NIC should be ON.
Connecting to an External Ethernet Hub or Switch:
1 Connect the Ethernet cable (with RJ-45 connector) to WAN port.
2 Connect the other end of the Ethernet cable to DSL/Cable modem or the external Ethernet hub or switch.
3 The LED indicators on both the LAN port and the external Switch.
18
Port Description
FXS(Foreign Exchange Station) FXS port can be connected to analog telephone sets or Trunk
Line of PBX.
FXO(Foreign Exchange Office) Can be Connected to PBX or CO line with RJ-11 analog line.
FXO port can be connected to the extension port of a PBX or directly connected to a PSTN line of carrier.
WAN(Wide Area Network) Connect to the network with an Ethernet cable. This port allows your GW to be connected to an Internet Access
LAN(Local Area Network)
RES(Reset button)
AC power(DC in 12V) device, e.g. router, cable modem, ADSL modem, through a networking cable with RJ-45 connectors used on 10BaseT and 100BaseTX networks.
Connect to PC with Ethernet cable. 1 port allows your PC or
Switch/Hub to be connected to the GW through a networking cable with RJ-45 connectors used on 10BaseT and
100BaseTX networks.
Push this button until 3 seconds, and GW will be set to factory default configuration.
A power supply cable is inserted
The hardware installation is now complete. The following sections will guide you through setting up your management PC and connecting to the Web User Interface.
2.3 Setup
There are 3 way to setting gateway - [Web User Interface] [Telnet] [Console] (8 port /16 port
/ 24 port Series modules Gateway have RS-232 console port).
2.3.1 Factory Default setting
WAN Port IP address : 192.168.1.1
LAN Port IP address : 222.222.222.1
LAN DHCP Server enable IP range: 222.222.222.51 ~ 222.222.222.100
19
VoIP Number(2 port Series) Port_1~Port_2 number:100,200
VoIP Number(4 port Series) Port_1~Port_4 number:100,200,300,400
VoIP Number(8 port Series) Port_1~Port_8 number:100,200,300,400,500,600,700,800
VoIP Number(8 port Series
1U/19 inch Chassis
) Port_1 ~ Port 8 number : 101~ 108
VoIP Number(16 port Series
1U/19 inch Chassis
) Port_1 ~ Port 16 number: 101~ 116
VoIP Number24 port Series
1U/19 inch Chassis
) Port_1 ~ Port 24 number: 101~ 124
VoIP default setting was H.323 signal protocol, Direct Mode, Fast-Start and G.723 codec.
Default login authentication username : admin, password : admin
2.3.2 Console
RS-232 port (DB-9pin male connector), Configure the COM Port Properties as following:
1. Connect Gateway RS-232 port to PC COM Port.
2. Power on gateway.
3. Open Terminal Program (ie. Windows XP Hyper Terminal)
[Start] → [Program file] → [Accessories] → [communications] → [Hyper Terminal]
4. Create New connection. Select “Com” port that connect PC to gateway
20
Set "Bits per second" to 38400.
Set "Data Bits" to 8.
Set "Stop Bits" to 1.
Set "Flow control" to None.
6. Input “Enter” and Show Welcome display.
7. Login, input the Password to login.(Password as the same as Access, default is admin)
8. Setting Gateway Configure like telnet mode
(Setting Table following as Telnet Setting table)
2.3.3 Telnet
Connect WAN/LAN port to Internet or PC and gateway at the same subnet. you can use telnet remote to configure your gateway.
1. Connect Gateway online (Wan/Lan)
2. Remote Gateway by Telnet. If telnet successful, you will see Login display.
(For Example Telnet from LAN port: telnet 222.222.222.1)
3. Input Password (Gateway Access password, Default: admin), If login successful, you will enter the welcome display.
(1:Gateway Model 2:Firmware Version 3:Wan/Lan Status 4.DDNS Status 5:VoIP Status)
21
4. Gateway Telnet Setting Table, Use 1~9 a~z select setting, “ESC” is back setting.
Item Setting Option
Main
[1]Advanced Setup
[1]Advanced Setup
……1.WAN Setting
[1]Advanced Setup
……2.LAN Setting
[1]Advanced Setup
……3.Virtual Server
[1]Advanced Setup
……4.Dynamic DNS
[1] Advanced Setup.
[2] System Administration.
[3] Save Current Configurations.
[4] Upgrade Software.
[5] Ping.
[6] Logout.
[7] Restart.
1.WAN Setting
2.LAN Setting
3.Virtual Server
4.Dynamic DNS
5.Network Management
6.VoIP Basic
7.Dialing Plan
8.VoIP Advance Setting
9.Hot Line Setting a.Port Status
1.Change WAN Type to DHCP
2.Change WAN Type to Fixed IP
3.Change PPPoE Username
4.Change PPPoE Password
1.Change to Bridge Mode
2.Change LAN IP Address
3.Disable DHCP Server
4.Change Start IP Address
5.Change End IP Address
6.Change DNS Server IP
7.Change Lease Time
1.Add Virtual Server
2.Delete Virtual Server
1.Change DDNS username
2.Change DDNS password
22
[1]Advanced Setup
……5.Network Management
[1]Advanced Setup
……6.VoIP Basic
[1]Advanced Setup
……7.Dialing Plan
[1]Advanced Setup
……8.VoIP Advance Setting
3.Change DDNS domain name
4.Change DNS server IP
1.Change web server port
2.Change telnet server port
1.Change VoIP Protocol to H.323
2.Change Port Number/Account/Password
3.Enable/Disable Public account
4.SIP hunting setting
5.Change SIP Proxy Server IP Address/DNS
6.Use net2phone
7.Change Register Interval(seconds)
8.Enable/Disable SIP authentication
9.NAT Pass Method a.STUN Server address b.SIP realm c.Outbound Proxy Server address d.Change SIP Local Port
1.Add Outbound Direct Call
2.Delete Outbound Direct Call
3.Add Inbound Direct Call
4.Delete Inbound Direct Call
(1)Sip Advance
1.Set DTMF Relay Mode
2.Change FAX Mode
3.Change RFC2833 Payload(96-127)
(2)Telephone Advance
1.VAD(Silence Compression)On/Off
2.Change Codec
3.Enable/Disable UK PSTN Tone Detection?
4.Enable/Disable Dial Complete Tone
5.Dial Termination Key Setting
6.FXS Parameters Setting
1.Change FXS Impedance
2.Change Phone In Volume
3.Change Phone Out Volume
4.Flash Detection
5.Ring Frequency
6.FXS Battery reversal generation
7.FXO Parameters Setting
1.Change FXO Impedance
2.Change Line In Volume
3.Change Line Out Volume
4.Change FXO Tx Gain
5.Change FXO Rx Gain
6.Flash Duration
7 DTMF Tone Power
8.FXO Transmit Hybrid
9.
Answer Supervision Setting
a.
Change Ringer Voltage Threshold
b.
Enable Line Silence Disconnect
c.
Change FXO Answer delay time
d.
FXO Ringer Voltage Filter Setting
(3)Network Advance
1.Disable Smart QOS
2.Bandwidth Control
3.G.723 Bandwidth
23
[1]Advanced Setup
……9.Hot Line Setting
[2] System Administration.
4.G.729 Bandwidth
5.Set IP TOS
1.Change Port1 Hot Line Number
2.Change Port2 Hot Line Number…….(To your own port)
1.Save Configuration
2.Access Control
3.Set to Default
4.System Information
5.NTP Setting
6.Syslog Setting
2.3.4 Web User Interface
The gateway has a built-in HTTP(Web) server for configuration. Before you use the gateway to access the Internet, you should set up a management PC to log into the router for further configuration. The management PC may be configured with a fixed or dynamically assigned IP address. For a fixed IP address, use an IP address from a 192.168.1.0/24 network, such as
192.168.1.10.
For a dynamic IP address, you need to set the PC as a DHCP client, and then restart or renew the network settings. The DHCP server of router is enabled by default so the PC will then be assigned an IP address and related settings by the router. The following examples are for a
MicrosoftTM Windows 2000/XP machine set to use a dynamic IP address.
Checking the Network IP Configuration
The following explains how to setup the Transmission Control Protocol/Internet Protocol
(TCP/IP) in Windows 2000/XP. For more detailed information on TCP/IP setup, refer to the
Windows 2000/XP help files. For other operating systems refer to the user manuals.
1. On the desktop, Please enter start -> control panel -> network setting.” Click Properties. The
Network screen will open.
(Your particular system will be different from the screen shown here.)
Check that you have an Ethernet network card installed. If not, refer to the card manufacturer’s
24
documentation and install the card and drivers.
If your card is installed,
1. Click the Add button. The Select Network Component Type dialog box will open. The box will show four options: Client, Adapter, Protocol, and Service.
2. Select Protocol and click the Add button. The Select Network Protocol dialog box will open.
3. Select Microsoft in the left scrolling window then selects TCP/IP in the right, and click OK.”.
You will be returned to the Network dialog box.
Configuring the TCP/IP Protocol
1. On the Network dialog box Configuration card, select TCP/IP and then click Properties.” The
TCP/IP Properties dialog box will open.
2. On the IP Address tab, click Obtain an IP address automatically. As the DHCP (Dynamic Host
25
Configuration Protocol) server built into the router is enabled by default, your computer will get an
IP address, subnet mask, and other related IP network settings from the router.
3. On the DNS Configuration tab, click Disable DNS”.
4. Click the Gateway tab.
5. Make the New gateway and Installed gateways fields blank and click OK. A dialog box will pop up asking you to restart the PC. Click Yes”.
Checking TCP/IP settings
1. After completing the previous steps, click Start -> Run -> and type ipconfig /all. The IP
Configuration window will open. If the PC does not show an IP address in the 222.222.222.51 to
222.222.222.100 range, click the ipconfig /release button to release the current configuration.
Wait a few seconds and click “ipconfig/renew” to get a new IP configuration from the router.
2. If the IP configuration is correct, you will be able to use the PING diagnostic utility built into
Microsoft Windows to ping the router. Click Start -> Programs -> MS-DOS Prompt. A command mode window will open.Type “ping 222.222.222.1” (default IP of the router) to check the network connectivity. If both hardware and software are correct, your computer will receive a response from the router as shown on the next page. If not, verify that the Ethernet cable is connected to the router properly and the Ethernet port LED on the front panel is lit.
Connecting to the Web Configuration via a Web Browser
1. Launch the Web browser(IE or Firefox). Enter http://222.222.222.1 into the browser Address window and press the Enter Key
26
2. An authentication dialog box will open.
3. If this is a first time setup of the router, type “admin” as the User Name and the Password field as “admin”. Click OK.(Default username/Password is “admin”)
4. The Web Configuration Setup Main Menu will open. On the main page [Setup Wizard],
[Advanced Setup] and [System Information] were displayed.
Wizard for Quick Setup
Wizard for Quick Setup gateway, After finishing the authentication, the Main menu will display 3 parts of configuration, please click “Wizard Setup” to enter quick start:
3.1 WAN Port Type Setup
27
For most users, Internet access is the primary application. The Gateway series support the
WAN interface for Internet access and remote access. The following sections will explain more details of WAN Port Internet access and broadband access setup. When you click “WAN Port
Type Setup
” from within the Wizard Setup, the following setup page will be show.
Three methods are available for Internet Access:
Fixed IP User:
If you are a leased line user with a fixed IP address, fill out the following items with the information provided by your ISP.
IP Address: check with your ISP provider
Netmask: check with your ISP provider
Default Gateway: check with your ISP provider
ADSL Dial-Up User (PPPoE Enable)
Some ISPs provide DSL-based service and use PPPoE to establish communication link with end-users. If you are connected to the Internet through a DSL line, check with your ISP to see if they use PPPoE. If they do, you need to select this item.
28
User Name: Enter User Name provided by your ISP
Password: Enter Password provided by your ISP.
Retype Password: Enter Password to confirm again.
DHCP Client (Dynamic IP):
Get WAN IP Address automatically
IP Address: If you are connected to the Internet through a Cable modem line then a dynamic
IP address will be assigned.
3.2 Configuring NAT or Bridge setting:
29
Bridge Mode: Select S series Gateway as bridge.
NAT mode: LAN IP Network Configuration
IP Address: Private IP address for connecting to a local private network
(Default: 222.222.222.51).
Subnet Mask: Subnet mask for the local private network (Default: 255.255.255.0).
3.3 VoIP Call Protocol Setup
Step1 :
Configure VoIP Call Signal Protocols :
User could select H.323 or SIP Protocol, and click “select”
30
Step2 :
configure the numbering with phone/line ports.
Phone Number (FXS): The representation number is the phone number of the telephone that is connected to Phone port.
Line Number (FXO): Line ports are connected to the extension ports of the PBX system or the PSTN line. They have a common Line Hunting Group Number. When this number is dialed, the Gateway system will find a free FXO line connected to PBX. This hunting will skip all busy lines and absent lines and find only the idle line to the PBX. After the available line is found, you can hear the dial tone from PBX. After that, you can dial the needed phone number out through PBX.
Step3: Let GW Register to H.323 Gatekeeper(GK)/SIP Proxy Server
(If user does not have H.323 GK/SIP Proxy Server, Please go to Step 4: Outgoing Dialing
Plan)
H.323 Gatekeeper IP address:
There is a gatekeeper address fields. If this gateway does not want to register to any gatekeeper, just set value 0.0.0.0 to the primary gatekeeper address.
SIP Proxy Server IP addresses:
There is a SIP Proxy Server address fields. If this gateway does not want to register to any SIP Proxy Server, just set value 0 .0.0.0 to the sip proxy server address.
Step 4: Outgoing Dialing Plan
The purpose of “Outgoing Direct Call” setting is to let user create a proprietary dialing plan when this Gateway is not registered to any H.323 Gatekeeper or any SIP Proxy Server. This setting can also assign some dialing plan to local ports (including prefix strip, prefix addition).Through this setting, user can directly map a number to a specific gateway (IP address).
In the “Outgoing Dial Plan” settings.
31
“Leading Number” is the leading digits of the dialing number.
“Min Length” and “Max Length” is the min/max allowed length you can dial.
“Strip Length” is the number of digits that will be stripped from beginning of the dialed number.
“Prefix Number” is the digits that will be added to the beginning of the dialed number.
“Destination” is the IP address of the destination Gateway that owns this phone number.
Step 5: Finishing the Wizard Setup
After completing the Wizard Setup, please click “Finish” bottom. The VoIP Gateway will save the configuration and rebooting Gateway automatically. After 20 Seconds, you could re-login the
Gateway.
Gateway Setting
Gateway setting include in some of advance setting, SIP Proxy Server (SVR) setting,
Gatekeeper (GK) setting. There are many detail explain follow. Setting in “Advance Setting”.
In Advanced Setup, GW provides user two major parts function to configure: One is “Network
Setup”, the other one is “VoIP Call Setup”
SET Wizard
Advance Setup
System Administrator
32
Advanced Configuration:
Advanced Setting Label
Network Setup Label
WAN Setting
LAN Setting
Virtual Server
Dynamic DNS
Network Parameters
Sets/changes the WAN port Type like “Fixed IP”, “DHCP Client” or ”PPPoE”.
Modifies the IP address of the LAN port and setting DHCP Server parameters.
Remote user can access server such as Web or FTP at you local site via public IP address can be automatically redirected to local servers configured with private IP address.
Dynamitic DNS allows you to provide Internet users with a domain name to access your server.
Network Parameter allows you to modify the access port of gateway.
For example :
Setting HTTP port : 8080
Setting TELNET port is : 8081
(Default HTTP :80, TELNET: 23)
VoIP Setup
VoIP Basic
Dialing Plan
Advanced Setting
The S Series Gateway support 2 / 4 / 8 / 16 / 24 phone/line for SIP and H.323 VoIP call applications. You can configure these ports from this menu.
Users could apply any dial policy by setting Dial Plan including outgoing dial plan and incoming dial plan.
VoIP Gateway support for silence compression, DTMF Relay, Codec
Selection, FAX mode Option,
H323 Register Type and H.323 Fast-Start/Normal-Start function.
FXO AC impedance, Volume Adjustment, RRQ TTL, RFC2833
Payload, IP TOS,..etc
Hot Line Setting Let user can set up “hotline” to dial the phone number automatically.
Port Status Display the telephone interface status
33
Traffic Monitor
System Administration:
Display and Monitor the voice traffic and data traffic.
Management Label
Save Configuration
Access Control
You can save configuration and restart the gateway with the default configuration or with the current running configuration.
Users can Sets/changes the administrator password..
Set to Default
Backup/Restore
Configuration
System Information
SNTP Setting
You can restart the gateway with the default configuration.
User can backup the configuration file of Gateway to PC or Restore the configuration file from PC.
Display Software version, WAN Type, VoIP Status, VoIP Codec, Phone
Interface and System Tim.
SNTP (Simple Network Time Protocol) Configuration for synchronizing gateway clocks in the global Internet.
Gateway can sends log information to Syslog Server by UDP ports 514. Syslog Setting
Capture Packets
The gateway supports packets capture and save the packets to your PC.
User can use Network Protocol Analyzer “Ethereal” to analysis the packets. (Free down load from http://www.ethereal.com/ )
4.1 Network Configuration
4.1.1 WAN Port Type Setup
For most users,Internet access is the primary application. The S Series Gateway support the
WAN interface for Internet access and remote access. The following sections will explain more details of WAN Port Internet access and broadband access setup. When you click “WAN Setting”, the following setup page will be show. Three methods are available for Internet Access.
Static IP
34
PPPoE
DHCP
Static IP:
You are a leased line user with a fixed IP address; fill out the following items with the information provided by your ISP.
IP Address: check with your ISP provider
Subnet mask: check with your ISP provider
Default Gateway: check with your ISP provider
PPPoE for ADSL
Some ISPs provide DSL-based service and use PPPoE to establish communication link with end-users. If you are connected to the Internet through a DSL line, check with your ISP to see if they use PPPoE. If they do, you need to select this item.
User Name: Enter User Name provided by your ISP
Password: Enter Password provided by your ISP.
Retype Password: Enter Password to confirm again.
35
DHCP Client (Dynamic IP):
Get WAN IP Address automatically
IP Address: If you are connected to the Internet through a Cable modem line then a dynamic
IP address will be assigned.
(Note : WAN port display the IP address, Subnet Mask and Default gateway IP address if
DHCP client is successful)
4.1.2 Configuring LAN IP Address and DHCP Server
There are two kinds of network feature to configure: Bridge Mode and NAT Mode
Bridge Mode:
Select this Gateway as Bridge. Let gateway Lan port like Switch/HUB. (WAN Port and LAN
Port use the same IP address)
NAT Mode:
Each of the VoIP Gateway has two Ethernet interfaces, one is for connecting to local network users, and the other is for connecting to an external broadband device (i.e. DSL modem/router or
Cable modem). The LAN port is connected to the local Ethernet network. WAN is connected to the external broadband device. The LAN IP address/subnet mask is for private users or NAT users, and the WAN IP address/subnet mask is for public users.
LAN IP Network Configuration:
IP Address: Private IP address for connecting to a local private network
(Default: 222.222.222.1).
36
Subnet Mask: Subnet mask for the local private network
(Default: 255.255.255.0).
DHCP Server Configuration:
DHCP stands for Dynamic Host Configuration Protocol. It can automatically dispatch related IP settings to any local user configured as a DHCP client. The DHCP server supports up to 253 users (PCs) on
Yes:
Enables the DHCP server. No: Disables the DHCP server.
Start IP Address: Sets the start IP address of the IP address pool.
End IP Address: Sets the end of IP address in the IP address pool.
DNS Server IP Address: DNS stands for Domain Name System. Every Internet host. must have a unique IP address, also they may have a human friendly, easy to remember name such as www.yahoo.com. The DNS server converts the human friendly name into it’s equivalent IP address. (Default: None)
Primary IP Address: Sets the IP address of the primary DNS server.
Secondary IP Address: Sets the IP address of the secondary DNS server.
4.1.3 Virtual Server Setup
“Natural firewall” allows requests for Internet access from the local network. However, any request from the Internet to the local network is blocked. By setting the Virtual Server function, computers outside the Intranet are allowed to access specific ports of local client. The Virtual
Server Port Table may be used to expose internal servers to the public domain or open a specific port number to internal hosts. Internet hosts can use the WAN IP address to access internal network services, such as FTP, WWW, Telnet etc.
How to set a Virtual Server
The following example shows how an internal FTP server is exposed to the public domain. The internal FTP server is running on the local host addressed as 222.222.222.100.
Private IP: Specifies the private IP address of the internal host offering the service
Public Port: Specifies which port should be redirected to the internal host..
Private Port: Specifies the private port number of the service offered by the internal host.
Apply: Click here to add the port-mapping entry and enable the service.
37
4.1.4 Dynamic DNS
DDNS is a service that maps Internet domain names to IP addresses. DDNS serves a similar purpose to DNS: DDNS allows anyone hosting a Web or FTP server to advertise a public name to prospective users. Unlike DNS that only works with static IP addresses, DDNS works with dynamic IP addresses, such as those assigned by an ISP or other DHCP server. DDNS is popular with home network, who typically receive dynamic, frequently-changing IP addresses from their service provider. To use DDNS, one simply signs up with a provider and installs network software on their host to monitor its IP address.
How to use DDNS
First: you should register a new DDNS service account from this web site:
http://www.dyndns.com/newacct
(Attention, if you use static IP address, you can’t set DDNS in gateway. Use DDNS and Static IP at the same time, the dyndns will stop your DDNS service. Dyndns support DDNS service is Free, one account can create 5 different DDNS Domain Name )
User Name: Input your DDNS User Name
Password: Input your DDNS Password
Domain Name: Input you set from your DDNS.(ie.gateway.gotdns.com)
DNS Server IP: Input your DNS Server IP.
4.1.5 Network Management
Network Management,, access port configuration allows you to modify the HTTP port or
TELNET port for accessing VoIP gateway
(Default Parameter : HTTP Port is 80 ; TELNET Port is 23)
38
Http Server Port: Input you want to change Web access port (Default is 80)
Telnet Server Port: Input you want to change telnet access port (Default is 23)
4.2 VoIP Setup
Gateway support 2 VoIP protocol - H.323 / SIP, you can register to H.323 Gatekeeper or SIP proxy server. Gateway is not a softswitch, it only can use 1 VoIP protocol (SIP/H.323) at the same time! If you don’t register GK or Proxy server, you can make Peer to Peer call by IP address or domain name (Setting Dialing plan).
4.2.1 H.323 Setup
Gateway H.323 protocol support H.323 (v2/v3/v4), H.225, Q.931, H.245 and RTP/RTCP. Don’t support H.235 security, can’t use H.235 security Authentication Username / Password. H.323 protocol is not good at pass NAT/Firewall, the best way is installed gateway on Public IP Address when it use H.323.If you want to under NAT, gateway support NAT pass function when you use the same S Series Gateway. Other band gateway doesn’t promise this function can work fine!
1. Select H.323 protocol, if you use 16 port / 24 port Series, you can select different page to setting port number or others.
2. Configure the numbering with FXS / FXO ports.
39
(Depending on model: 16 port have 16 voice channels for setting, 24 port have 24 voice channels for setting)
FXS Number: The representation number is the phone number of the telephone that is connected to FXS port.
FXO Number: FXO ports are connected to the extension ports of the PBX system or the
PSTN line. They have a common Line Hunting Group Number. When this number is dialed, the Gateway system will find a free FXO line connected to PBX. This hunting will skip all busy lines and absent lines and find only the idle line to the PBX. After the available line is found, you can hear the dial tone from PBX. After that, you can dial the needed phone number out through PBX.
(Port number is in comparison with gateway port number. Gray Port socket is “FXO” port, Black
Port socket is “FXS” port.)
3. Configure the ANI (Answer Number Indication) / Caller ID of the FXS/FXO ports.
ITSP needs ANI for authorization when gateway calls Off-Net call to PSTN number or mobile phone number.
4. Register to H.323 Gatekeeper
40
(If user does not have Gatekeeper, Please go to Dialing Plan Policy)
H.323 Parameters Label
H.323 ID
Sets the unique name of this Gateway, that is communicated as part of
H.323 messaging..
Primary Gatekeeper
IP Address
Secondary Gatekeeper
IP Address
There are two gatekeeper address fields, one is primary, the other secondary. If this gateway does not want to register to any gatekeeper, just set value 0 to the primary gatekeeper address. If the primary gatekeeper address is not 0, the gateway will register to the primary gatekeeper. If the second gatekeeper is not 0, the gateway will try to register to the second gatekeeper when failed to register to primary gatekeeper, i.e. if both the primary gatekeeper and second gatekeeper addresses are present, the gateway will try to register to these two gatekeepers respectively. The gateway can have the gatekeeper backup function by this way.
Primary Gatekeeper
Domain Name
Secondary Gatekeeper
Domain Name
Let user use Domain Name of H.323 Gatekeeper.
H.323 Gatekeeper ID
Voice Cap Prefix
RAS Port Adjustment
Q.931 Port Adjustment
The Gatekeeper ID; usually do not need to set this field unless the gatekeeper must need this value.
Let user set prefix number in RRQ nonstandard voice cap entry.
In H.323 standard the RAS default port number is 1719. The VoIP gateway provides user to change RAS port number to meet the network environment.(Some area carrier blocks or forbidden the default port number)
In H.323 standard the default Q.931 port number is 1720. The VoIP gateway provides user to change Q.931 port to meet the network environment. (Some area carrier blocks or forbidden the default port number)
H.323 Call Pass through NAT
41
H.323 Pass Through
NAT method
1. Disable : The Gateway operates in public IP address
2. Auto Detection: When the Gateway register to GNU Gatekeeper /
H.323 Gatekeeper (SK Series), please select this option.
3. Manual Setting: When the Gateway registers to H.323 Gatekeeper and operate under NAT (enable DMZ), please select this option and key in IP address.
H.323 VoIP Advanced Configuration
There are many H.323, VoIP, Codec and other more detail Setting, you can set in “Advance
Setting
”. For SIP and H.323, there are a little different in advance setting. There are 3 different parts to setting about VoIP, Telephone and network.
[Advance Setting]
Item Description
DTMF Relay for H.323:
H.323 Mode:
After the VoIP call is connected, when you dial a digit, this digit is sent to the other side by DTMF tone. There are two methods of sending the DTMF tone. The first is “in band”, that is, sending the
DTMF tone in the voice packet. The other is “out band”, that is, sending the DTMF tone as a signal. Sending DTMF tone as a signal could tolerate more packet loss caused by the network. If this selection is enabled, the DTMF tone will be sent as a signal.
This selection could force the Gateway to use normal start mode
(default mode) or fast start mode when establishing a VoIP call.
Many other gateways only support normal start mode, enable this selection when it is necessary. The default is disabled (using fast start mode).
H.323 H.245 Tunneling:
This selection could force the Gateway to use H.245 Tunneling when establishing a VoIP call The default is disabled (using fast start mode).
FAX Mode Option:
T.30/T.38 real-time FAX compliant Voice/FAX auto-switch. The
T.38 is a “Real Time Group 3 Fax Communication over IP network” format. That’s meaning it’s a protocol for Fax over IP.
You have to enable this function
(T.38 mode isn’t support all gateway, different band use T.38 have a little change, it maybe let T.38 FAX Error)
H.323 Registration type:
There are 2 choices for this setting. “Gateway” means it will act as the VoIP gateway. “Terminal” means it will act as the IP phone terminal.
42
H.323 RRQ TTL:
H.323 Autoanswer:
MAC Authentication:
Watchdog:
[Telephone Advance]
This command configures the number of seconds that the gateway should be considered active by the H.323 gatekeeper.
The gateway transmits this value in the RRQ message to the gatekeeper. The default value is “0”.
When a VoIP call is incoming, the Gateway will ring a specific phone set. The H.323 call signaling part could be connected or alerting during this ringing period. If this selection is enabled, the
H.323 signaling part is connected during the ringing period. The benefit of this situation is that the remote side could hear the status of the specific port. That is, the remote side will hear ring back tone if the Gateway is really ringing the phone set. If the phone set is busy, the remote side will hear busy tone. The disadvantage of this situation is that the H.323 connected time is not the real voice call connected time. So, if billing is recorded for this Gateway, this function should be disabled.
Some Gatekeeper register need UA send MAC address to
Authentication, you need enable this function.(Default is disable).
When your gateway shutdown, or something happen that made gateway can’t work fine. Watchdog will reboot your gateway automatically when it can’t work.
43
Item
Silence Compression:
(VAD)
Voice Codec option:
Dial Complete Tone:
Description
If this function is enabled, when silence is occurred for a period of time, no data will be sent across the network during this period in order to save bandwidth.
(If you use Asterisk, please disable Silence Compression, it maybe make you call disconnect.)
The Codec is used to compress the voice signal into data packets. Each Codec has different bandwidth requirement. There are four kinds of Codec, G.723, G.729AB, G.711_u and G.711_A.
The default value is G.723.
When you use the VoIP call, you will heard “DuDu” voice that is dial complete tone. If you don’t want to heard that tone , you can disable it.(default is enable).
Setting Termination key to speed up VoIP dial. Select “*” or “#” to
Termination key.
The FXS provides 600/900 OHM impedances for selection.
Dial Termination key:
FXS Impedance:
FXO AC Impedance:
Phone (Line) in/out volume:
FXO Tx/Rx Gain:
UK PSTN release tone detection:
FXO/FXS Flash detection and generation duration :
Ring Frequency:
DTMF tone power:
FXO Transmit Hybrid:
The FXO provides wild and complex ac termination impedances for selection.
You can adjust the Phone (Line) in/out volume, range from -9db to
9db
(If you adjust too bigger, maybe generation some ECHO or noise)
You can adjust the FXO Tx/Rx Gain , range from -6db to 6db.
(If you adjust too bigger, maybe generation some ECHO or noise)
When you use the Gateway to UK, you can Enable this selection to detection release tone
Flash Detection: Let you change flash detection (milliseconds) of
Gateway when phone generate flash to FXS.
Flash Generation: Let you change flash generation time
(milliseconds) for PBX detection.
You can configure how long the Ring Frequency do you want to use.
Sometimes you input DTMF, but no request. You can adjust this function, range from -6db to +6db.
ECHO cancellation adjust, 3 mode setting to solve ECHO problem, default is Mode 1. If you have echo problem, try to select
44
FXO Ringer Voltage
Threshold:
FXO Ringer Voltage filter:
FXS Battery Reversal
Generation:
FXO Answer Supervision
Line Silence Disconnect:
FXO Answer Delay Time
FXO Answer Mode
other Option.
Sometime you use FXO connect to PSTN/PBX can’t be pick up the call. PSTN/PBX can’t detection FXO voltage, you can adjust this function. Default is low.( Low : 16.5 Vrms Medium: 24 Vrms
High: 49.5 Vrms)
Some vendor’s PBX generates the leakage voltage from extension port. That will mislead the FXO become Off-hook status. This function was set to avoiding a leakage voltage signal is detected as ring coming.
Some Payphone need Battery Reversal to count call money.
Gateway FXS can generation that Battery Reversal. If you don’t use this function , don’t enable it.
Enable battery reverse to detect polarity from PSTN line. The
PSTN line can send. H.323 case: Sending the Q.931 connect signal to caller when detecting polarity reverse from PSTN Line.
SIP case: Sending the 200 OK connect signal to caller when detecting polarity reverse from PSTN Line.
Voice Detection: when the FXO connect PSTN/PBX, gateway will detection the PSTN/PBX send voice , it will send Q.931 connect or SIP 200 ok.
When FXO call have silence, the call will disconnect automatically. {Default is Disable}
Some PSTN/PBA when call incoming can’t pick up first time. It need delay few second time. You can set FXO pick up call delay time.(default is 0)
FXO Answer Mode Concept:
When user calls the PSTN line which was connected with the
FXO port, there are three answer mode for user to configure.
1. Ringing Answer Mode (Default Setting): FXO answer the call once the ring coming from PSTN line.
Case A:
“Hot Line Number” was NOT assigned in the FXO port. FXO answer the call once the ring come from PSTN line.
Case B:
“Hot Line Number” was assigned and the Hot line number belongs to remote VoIP device.
In this case, FXO port will not answer (off-hook) the PSTN till the user picks up the call.
(Note: This case can avoid charging for the Local PSTN call when the remoting VoIP devic still ring.)
Case C:
“Hot Line Number” was setting and the Hot line number was assigned to another FXS port in same Gateway.
FXO port will not answer (off-hook) till the Phone (connected to the FXS port) was picked up by user.
(Note: This case can avoid the Local PSTN charge when the
FXS port still ring.)
3. Non Answer Mode: FXO will NOT answer the call in any time.
(Note: Some ITSP only let the FXO for termination function, they do not user use the FXO port for origination)
45
[Network Advance]
Item
Smart-QoS:
Description
If this function is enabled, when VoIP call is occurred, the other data will be automatically reduced traffic which across the internet in order to guarantee the voice bandwidth.
Bandwidth control:
G.723/G.729 Bandwidth:
You can configure your bandwidth what the Max byte of download and upload of ADSL modem rate.
Setting G.723 / G.729 voice compression size. Quality and Packet size can adjust by you want.
IP TOS:
Some Router support TOS(Type of Service), when you enable the
TOS function, the router will process those packets firstly.(default is disable)
46
4.2.2 SIP Setup
Gateway SIP support SIP(RFC3261), SDP(RFC2327), RFC2833, STUN(RFC3489), Symmetric
RTP, outbound proxy, ENUM(RFC2916),and RTP/RTCP.SIP NAT pass through Function can support 80% NAT/Firewall that you don’t setting DMZ/Virtual server in router or Firewall.
1. Select “SIP Protocol”
2. SIP number / account (username) and Password Setting: Please fill out the SIP account including username / password from ITSP.
(Note: support digits and character base SIP Account / username, some SIP Server use character username to login, and a number to call number( ie. VoIPBuster) , if your server don’t support this, number/Account are the same, please input the same username )
Number: Input SIP Number(Username), if your server support account and number
(different),input the number, else number/account are the same username.
Reg: let your sip account register SIP Server, click this option.
Account: Input SIP account(Username), if your server support account and number
(different),input the number, else number/account are the same username.
Password: Input Password that ITSP support.
Use Public Account:
This allows gateway can use single SIP account for multiple ports.
User input the only one account in port one field for registering the ITSP.
47
SIP Hunting Table:
This allows gateway can answer SIP call from internet by Hunting. For example: Port 2-7 are hunting for the Port 1 SIP account. When port 1 are on call, the other one SIP call from internet will ring port 2. 2 port / 4 port / 8 port Series hunting table is use click box.
3. SIP Proxy Server setting, setting SIP proxy server register information.
(If user does not need register SIP Proxy Server, Please go to Dialing Plan Policy)
SIP Proxy Server Label
SIP Proxy Server Setting
SIP Domain
Register Interval Setting
SIP Authentication
1. Enter the SIP service IP address or domain name in this field (the domain name that comes after the @ symbol i n a full SIP URI).
2. Use Net2Phone Service Provider
1. Enter the SIP realm in this field
This field sets how long an entry remains registered with the SIP register server. The register server can use a different time period.
The Gateway sends another registration request after half of this configured time period has expired.
Enable or Disable MD5 Authentication with SIP Proxy Server
48
4. If your gateway under the NAT/Firewall, you should setting different NAT Pass function. if you setting STUN/Outbound Proxy, you should have a STUN/Outbound proxy server. If they can’t pass NAT or one way talk happen, try to open “DMZ” and virtual server “5060” port in router.
Symmetric RTP: default use Nat pass function.
STUN Client: setting your STUN server information, default STUN server is FWD STUN server.
Outbound Proxy Support: Setting your Outbound Proxy server information.
Local SIP Port:: setting local use SIP port, default is 5060.
SIP VoIP Advanced Configuration
There are many SIP VoIP, Codec and other more detail Setting, you can set in “Advance
Setting
”. For SIP and H.323, there are a little different in advance setting. There are 3 different parts to setting about VoIP, Telephone and network.
[VoIP Advance]
Item Description
DTMF Relay for SIP:
After the VoIP call is connected, when you dial a digit, this digit is sent to the other side by DTMF tone. There are three methods of sending the DTMF tone. The first one is “in band”, that is, sending the DTMF tone in the voice packet. The second one is “RFC2833”, that is, sending the DTMF tone as a RTP payload signal. The third one is
“SIP Info”, that is, sending the DTMF tone as a SIP signal. Sending
DTMF tone as a signal could tolerate more packet loss caused by the
49
RFC2833 Payload:
FAX Mode Option:
Watchdog:
[Telephone Advance]
network. If this selection is enabled, the DTMF tone will be sent as a signal.
Adjust RFC2833 DTMF payload value, range from 96 to 127, default is 101.
T.30/T.38 real-time FAX compliant Voice/FAX auto-switch. The T.38 is a “Real Time Group 3 Fax Communication over IP network” format.
That’s meaning it’s a protocol for Fax over IP. You have to enable this function
(T.38 mode isn’t support all gateway, different band use T.38 have a little change, it maybe let T.38 FAX Error)
When your gateway shutdown, or something happen that made gateway can’t work fine. Watchdog will reboot your gateway automatically when it can’t work.
50
Item
Silence Compression:
(VAD)
Voice Codec option:
Dial Complete Tone:
Description
If this function is enabled, when silence is occurred for a period of time, no data will be sent across the network during this period in order to save bandwidth. (If you use Asterisk, please disable
Silence Compression, it maybe make you call disconnect.)
The Codec is used to compress the voice signal into data packets. Each Codec has different bandwidth requirement. There are four kinds of Codec, G.723, G.729AB, G.711_u and G.711_A.
The default value is G.723.
When you use the VoIP call, you will heard “DuDu” voice that is dial complete tone. If you don’t want to heard that tone , you can disable it.(default is enable).
Setting Termination key to speed up VoIP dial. Select “*” or “#” to
Termination key.
The FXS provides 600/900 OHM impedances for selection.
Dial Termination key:
FXS Impedance:
FXO AC Impedance:
Phone (Line) in/out volume:
FXO Tx/Rx Gain:
Ring Frequency:
DTMF tone power:
UK PSTN release tone detection:
FXS/FXO Flash detection and generation duration :
The FXO provides wild and complex ac termination impedances for selection.
You can adjust the Phone (Line) in/out volume, range from -9db to
9db.
(If you adjust too bigger, maybe generation some ECHO or noise)
You can adjust the FXO Tx/Rx Gain , range from -6db to 6db.
(If you adjust too bigger, maybe generation some ECHO or noise)
When you use the Gateway to UK, you can Enable this selection to detection release tone
Flash Detection: Let you change flash detection (milliseconds) of
Gateway when phone generate flash to FXS.
Flash Generation: Let you change flash generation time
(milliseconds) for PBX detection.
You can configure how long the Ring Frequency do you want to use.
Sometimes you input DTMF, but no request. You can adjust this function, range from -6db to +6db.
51
FXO Transmit Hybrid:
FXO Ringer Voltage
Threshold:
FXO Ringer Voltage filter:
FXS Battery Reversal
Generation:
FXO Answer
Supervision:
Line Silence Disconnect:
FXO Answer Delay Time
FXO Answer Mode
ECHO cancellation adjust, 3 mode setting to solve ECHO problem, default is Mode 1. If you have echo problem, try to select other Option.
Sometime you use FXO connect to PSTN/PBX can’t be pick up the call. PSTN/PBX can’t detection FXO voltage, you can adjust this function. Default is low.( Low : 16.5 Vrms Medium: 24 Vrms
High: 49.5 Vrms)
Some vendor’s PBX generates the leakage voltage from extension port. That will mislead the FXO become Off-hook status. This function was set to avoiding a leakage voltage signal is detected as ring coming.
Some Payphone need Battery Reversal to count call money.
Gateway FXS can generation that Battery Reversal. If you don’t use this function, don’t enable it.
Enable battery reverse to detect polarity from PSTN line. The
PSTN line can send. H.323 case: Sending the Q.931 connect signal to caller when detecting polarity reverse from PSTN Line.
SIP case: Sending the 200 OK connect signal to caller when detecting polarity reverse from PSTN Line.
Voice Detection: when the FXO connect PSTN/PBX, gateway will detection the PSTN/PBX send voice , it will send Q.931 connect or SIP 200 ok.
When FXO call have silence, the call will disconnect automatically. {Default is Disable}
Some PSTN/PBA when call incoming can’t pick up first time. It need delay few second time. You can set FXO pick up call delay time.(default is 0)
FXO Answer Mode Concept:
When user calls the PSTN line which was connected with the
FXO port, there are three answer mode for user to configure.
4. Ringing Answer Mode (Default Setting): FXO answer the call once the ring coming from PSTN line.
Case A:
“Hot Line Number” was NOT assigned in the FXO port. FXO answer the call once the ring come from PSTN line.
Case B:
“Hot Line Number” was assigned and the Hot line number belongs to remote VoIP device.
In this case, FXO port will not answer (off-hook) the PSTN till the user picks up the call.
(Note: This case can avoid charging for the Local PSTN call when the remoting VoIP devic still ring.)
Case C:
“Hot Line Number” was setting and the Hot line number was assigned to another FXS port in same Gateway.
FXO port will not answer (off-hook) till the Phone (connected to the FXS port) was picked up by user.
(Note: This case can avoid the Local PSTN charge when the
FXS port still ring.)
6. Non Answer Mode: FXO will NOT answer the call in any time.
(Note: Some ITSP only let the FXO for termination function, they do not user use the FXO port for origination)
52
[Network Advance]
Item Description
Smart-QoS:
Bandwidth control:
G.723/G.729 Bandwidth:
IP TOS:
If this function is enabled, when VoIP call is occurred, the other data will be automatically reduced traffic which across the internet in order to guarantee the voice bandwidth.
You can configure your bandwidth what the Max byte of download and upload of ADSL modem rate.
Setting G.723 / G.729 voice compression size. Quality and Packet size can adjust by you want.
Some Router support TOS(Type of Service), when you enable the
TOS function, the router will process those packets firstly.(default is disable)
4.2.3 Direct call (Peer to Peer) setup
If you don’t registered Gatekeeper or SIP proxy server, you can make call by Peer to Peer. For
SIP or H.323, setting the dialing plan, and can make direct call.
Overview of the Dialing Plan
The “Dialing plan” need setting when the user use the method of Peer-to-Peer H.323 (SIP)
VoIP call or registering H.323 Gatekeeper (SIP Proxy Server) Mode. The H.323(SIP) Dialing Plan has two kinds of directions: Outgoing (call out) and Incoming (call in).
Peer-to-Peer Call Mode: Effective
Registering to H.323 Gatekeeper (SIP Proxy Server) Mode: Effective
2. Incoming Dial Plan:
Peer-to-Peer Call Mode: Effective
Registering to H.323 Gatekeeper (SIP Proxy Server) Mode:
The leading number would
register
to H.323 Gatekeeper (SIP Proxy Server)
When you use direct call, you must setting your VoIP protocol firstly. Use direct call, you should setting the same protocol both of UA. Both of UA must support dial plan function. Some ATA don’t support Dialing plan, it maybe let direct call failed.
53
In the “Outgoing Dial Plan Configurations” settings: Maximum Entries : 50
“Outbound number” is the leading digits of the call out dialing number.
“Length of Number” has two text fields need filled: “Min Length” and “Max Length” is the min/max allowed length you can dial.
“Delete Length” is the number of digits that will be stripped from beginning of the dialed number.
“Add Digit Number” is the digits that will be added to the beginning of the dialed number.
“Destination IP Address / Domain Name” is the IP address / Domain Name of the destination
Gateway that owns this phone number.
“Destination Port” is port of the destination gateway use.(Default is 5060)
Example1: Normally Dial
1.001x leading call out, call to Destination IP address: 211.22.3.14
2.002x leading call out, call to Destination Domain Name: h.323.gw.net
Example2: Speed Dial
1. If user dial “401”,
Gateway automatically dial “1334588712” to Destination IP address: 211.22.3.14
2. If user dial “402”,
54
Gateway automatically dial “2212345612” to Destination IP address: 211.21.2.76
In the “Incoming Dial Plan Configurations” settings: Maximum Entries : 50
“Inbound number” is the leading digits of the dialing number.
“Length of Number“ has two text fields need filled: “Min Length” and “Max Length” is the min/max allowed length you can dial.
“Delete Length” is the number of digits that will be stripped from beginning of the dialed number.
“Add Digit Number” is the digits that will be added to the beginning of the dialed number.
“Destination Tele port” is “Tel-port”; this is for local dial plan setting phone number.
Example1: Hunting for FXS Port
Port 1: FXS
Port 2: FXS
Port 3: FXS
Port 4: FXS
H.323 (SIP) number “123”call incoming, Port 1 will be ringing.
If Port 1 is busy, Port will be ringing.
If Port 1 and 2 are busy, Port 3 will be ringing.
If Port 1, Port 2 and Port 3 are busy, Port 4 will be ringing.
Example2: Hunting for FXO Port
Port 1: FXO was connected to PSTN.
Port 2: FXO was connected to PSTN.
Port 3: FXO was connected to PSTN.
Port 4: FXO was connected to PSTN.
H.323 (SIP) number “123”call incoming, Port 1 will be off-hook and hear the Dial Tone from
PSTN.
If Port 1 is busy, Port will be will be off-hook and hear the Dial Tone from PSTN.
If Port 1 and 2 are busy, Port 3 will be off-hook and hear the Dial Tone from PSTN.
If Port 1, Port 2 and Port 3 are busy, Port 4 will be off-hook and hear the Dial Tone from
PSTN.
55
Example3: Termination Call to FXO for One-Shoot Call
Port 1: FXO was connected to PSTN (area code is 81xxxxxxxx).
H.323 (SIP) leading number “081x”incoming, and delete the first one digit “0”, and call to
PSTN number.
Example4: Termination Call to FXO
Port 1: FXS
Port 1: FXO was connected to PSTN (area code is 92xxxxxxxx).
Port 1 FXS call to “092x” to PSTN, FXO port will delete the first one digit “0” and call to
PSTN number.
( [x]: mean wild card, 0~9. Speed dial: When you dial over the number, input “#” key can speed dial call, or you key in number as the length as the “length of number” )
4.2.4 Other VoIP Setting
Hot Line:
You can setting hot line. when the call incoming the hot line port, it will call hot line number automatically. The hot line call the number via VoIP, so you setting the hot line number must VoIP number. Usually, you want to FXO port call transfer to FSX, you only setting the FXO hot line to
FXS number.
Port number: Input FXS/FXO want to call hot line number. The call will via VoIP, so the number must be the VoIP number.
56
Port Status:
Each of port show status table. you can view all port status. like on/off hook , caller/callee IP, duration , and packet loss. (16 port / 24 port Series can change page to view all ports)
Port Status Display : This selection will display concurrent call status of this Gateway. The status information of each voice channel includes codec, dialing number and destination IP address. The status is refreshed every 3 seconds.
Call Priority:
Gateway have a rule for call Priority, up to down is 1)Hot Line 2)Dialing plan 3)Registered server(SIP Proxy / H.323 Gatekeeper).When a VoIP call made, Gateway will process by Hot Line first, then it will check the dialing plan table, the last process is checking register server(SIP Proxy
Server / H.323 Gatekeeper).
For example, if I have a gateway , and It is registered a proxy server, I don’t setting any others
(Hot Line or dialing plan.). when I make a VoIP call, the call will go to Proxy server. If user set 1~2 dialing plan also let gateway registered to proxy server. When user place an call, gateway will check the dialing plan first, then check the proxy server. And so on…..
57
4.6 System Administrator
You can setting other gateway setting, like gateway time, Syslog that send CDR information to
Syslog server, backup and restore configuration.
4.6.1 Save Configuration and Reboot
Save Configuration and Reboot”
to save configuration and begin to restart.
(When you set done, select “Reboot” option will auto save and reboot!)
4.6.2 Access Control
Changing the Administrator Password
For security reasons, we strongly recommend that you set an administrator. password for the
58
router. On first setup the router requires no password. If you don’t set a password the router is open and can be logged into and settings changed by any user from the local network or the
Internet.
Click , the following screen will open.
(Guest account , if you use guest account login , you only can view gateway setting, not change and configure any gateway setting, else you login by Admin account)
4.6.3 Set To Default Configuration
If you want to reboot the router using factory default configuration, click “Apply” then reset the router’ s settings to default values.
4.6.4 Backup/Restore Configuration to a File (Optional firmware)
User can Backup the parts configuration in gateway to a File at Microsoft Operation System.
And also restore the configuration file to the GW from PC.
There are two parts backup/restore configuration for setting.
User can backup Dial Plan list only or backup the voip basic only
4.6.5 System Information Display Function
59
Click System Information Display to open the Online Status page. In the example, on the following page, both PPPoE connection is up on the WAN interface, H323 Status, MAC address, Register Status, etc….
4.6.6 SNTP Setting Function
.
Click SNTP Setting to open the Online Status page. In the example, on the following page,
Use SNTP Setting
—When checked, Gateway uses a Simple Network Time Protocol (SNTP) to set the date and time . The Gateway synchronizes the Gateway’s time after you select the time zone. Use SNTP Setting, Select the time zone which Gateway was at.
60
4.6.7 Syslog Setting Function
Use Syslog server to record your Gateway log file. you can setting you syslog server IP address for this function. Syslog information include the CDR source!
4.6.7 Capture Packets Function
Use “Capturer Packets” to record Gateway packets. You can start and stop the capture then save the file to PC Use the Ethereal Tool ( www.ethereal.com
) to analyze the packets.
(if gateway have interoperability problem, you can capture the packet, send to us . we can refer this packet to bebug.)
61
4.7 Upgrade firmware
Gateway can upgrade Firmware via FTP in “Telnet Mode”, upgrade the firmware can add new function or fix some bug. If your gateway works fine, you don’t need update any new firmware.
The new firmware maybe let your gateway not stable. you can get the last version firmware on our web site or send support mail to us, we will mail firmware to you.
Firmware name is “S400.282”, the first name s400 is mean the gateway module. There are 3 module name use different firmware. 2 port / 4 port gateway are use the Firmware first name
“S400”, 8port gateway use the “S800”, 16port/ 24port series use the “s2400”. The second name is the firmware version. For example, “s400.282” is mean that firmware use 2 port / 4 port module, version is 2.8.2.
(Gateway update firmware only support use telnet mode via FTP, no other else upgrade function.)
FTP upgrade Requirement and Process
1. Environment Requirement
PC with FTP Server (Server-U software, 3CDaemon,..)
PC or Notebook witch connected to LAN port of Gateway.
Put the image (firmware) named “s400.xxx” at the assigned folder in FTP Server.
( for example: “s400.270” is version 2.7.0 )
Note: Our company FTP server, you can use it to upgrade
Free FTP server : 61.218.109.83 username: share , password: 19730809
Environment Architecture (Gateway and FTP server are in Internet):
FTP Server
Notebook
VoIP Gateway
WAN Port
LAN Port
Internet
2. Upgrading Process
Notebook Telnet VoIP GW
[Open DOS mode]
-> C:> telnet 10.10.10.1 (Default LAN port IP address) (before version 2.6.5)
-> C:> telnet 222.222.222.1 (Default LAN port IP address) (after version 2.6.6)
Please select [4] Upgrade Software
62
Please input IP address of FTP server like as : 61.218.109.83
Username : share
Passswd : 19730809
Imagename: s400.271
Upgrade (y/n) : y , then will write the firmware to flash.
(In different module or firmware , maybe have different change)
After writing flash, Please reboot the Gateway.
If the new firmware (image) was most different with the previous version, please
push
the
63
hardware reset bottom to set to default.
If the VoIP Gateway is in remote site, please use WEB configuration to
set to default.
Appendix
A FAQ List
1. What is the default administrator password to login to the gateway?
A:
By default, your default username is “admin”, default password is “admin” to login to the router.
For security, you should modify the password to protect your gateway against hacker attacks.
2. I forgot the administrator password. What should I do?
A:
Press the Reset button on the rear panel for over 5 seconds to reset all settings to default values. Default username / password is admin / admin.
3. What is the default IP address of the router?
A:
The default WAN IP address is 192.168.1.1 with subnet mask 255.255.255.0.
The default LAN IP address is 222.222.222.1 with subnet mask 255.255.255.0.
4. Why is it that I can ping to outside hosts, but not access Internet Web sites?
A:
Check the DNS server settings on your PC. You should get the DNS servers settings from your ISP. If your PC is running a DHCP client, remove any DNS IP address setting. As the router will assign the DNS settings to the DHCP-client-enabled PC.
5. What is the maximum number of IP addresses that the DHCP server of the gateway can assign to local PCs?
A:
The built-in DHCP server can support 253 IP addresses for local network usage.
6. What is different [set to default] in WEB UI and [Factory set to default] of RST bottom?
A:
Factory set to default of RST bottom, you must push RST button until 5 second, gateway will clear all your setting, and let gateway Wan/Lan port become the factory default(192.168.1.1/222.222.222.1). When you use setting to default by Web UI or Telnet mode, it will clear all your setting, but the WAN port IP Address mode setting will be kept. If you remote the gateway, after set to default, you can login gateway again. No reset the gateway wan port again.
7. What is the Flash?
64
1. PSTN Call from PSTN to Office PBX and dial the extension 102 go to Gateway
2. Call to Gateway of Home by Hotline.
3. Home user needs call transfer to extension number 101.
4. Dial Flash and Gateway FXS detect and generate the Flash to PBX in Office.
Flash is mean on-hook and off-hook fast switch, on-hook and off-hook duration. It usually use on PBX system, in place of transfer function key.
8. Why can I call out when the gateway under the NAT?
A:
VoIP product almost have NAT Pass through problem. By SIP, there are many NAT Pass through Function can solve 80% NAT Problem. You can choose STUN/Outbound Proxy/
Symmetric RTP to Pass through NAT, you don’t set any other setting (DMZ/Virtual Server) by router side. If you use STUN/Outbound Proxy, you must have a STUN/Outbound Proxy Server to support. If they can’t pass NAT, please open the DMZ/Virtual Server by Router/NAT/Firewall.
9. Why does the one way talk happen?
A:
Generally, one way talk happen when use the different codec between VoIP device make call.
Please check and setting the same codec, most one way talk will be solved.
10. Why can I call out by Gateway?
A:
Please chick your Gateway is registered SIP Proxy Server (ITSP), and chink your Internet works fine. Gateway can’t make a call without Internet or SIP Account that from ITSP supply. You must have a SIP account or know the other Gateway IP/Domain Name, then you can make a
VoIP call.
11. I can’t use web Interface to setting gateway. How can I do?
A:
Please check you PC connect the Gateway Lan port or PC and ATA with the same Subnet. If you PC aren’t at the same Subnet, you can’t Login the gateway Web interface. Else you let your gateway on Public Internet(Public IP address).when you Lan and Wan can’t login always, try to set factory default. (Push RST button until 5 second), and try again
12. Why I use asterisk by G.729 sometimes disconnect happen?
A:
In asterisk setting VAD must disable, if you open Silence Compression (VAD), it will make call disconnect happen, please disable the option when you use the asterisk.
13. Can I use re-invite function when server is asterisk?
A:
The new firmware will support re-invite. [After version 2.8.2 (included 2.8.2)]
14 Why can’t register and use after setting?
65
A:
After setting, please save configuration and reboot, after reboot you can use new configuration.
15. Why I can’t use FAX?
A:
The VoIP FAX has 2 mode, one is T.30, another is T.38. T.30 use voice date to FAX, so usually T.30 FAX by VoIP is work. There are some problem with T.38. Because T.38 is use protocol and data packet to sand FAX, different platform and device maybe have different change, that made the T.38 filed. If you can use T.38 to FAX, Please try to use T.30.
B SIP Setting VoIPBuster
VoIPBuster Service Using IP-Telephony VoIP Gateway
The IP-Telephony 2 port / 4 port / 8 port / 16 port / 24 port VoIP Gateway can register to
VoIPBuster (http://www.voipbuster.com) VoIP service by SIP protocol and also can call SIP calls by VoIPbuster (http://www.voipbuster.com) service.
Gateway Setting
1. VoIPBuster SIP Proxy Server : sip.voipbuster.com / 5060
2. VoIPBuster STUN Server: stun.voipbuster.com / 5060
3. VoIP Basic -> Setting SIP accounts and Set the Proxy Server and STUN server.
66
How to dial the call?
00 - country code – area code
For example IP-Telephony company phone number is +886-35733113, the dial number is
0088635733113
VoIPBuster Provides Free Land Line (Fixed Line) Calls
67
C Answer supervision
This is designed to help explain and resolve issues of answer supervision from a switch or
PSTN provider that could result in billing for termination calls.
Gateway provides 2 Types of Answer Supervision:
1. Loop-Start Reverse Battery, Reverse battery (also called Polarity Reverse) is when the PSTN provider reverses the polarity of the battery voltage, for both answer supervision and disconnect supervision.
2.
Voice Detection-based answer supervision is a feature where the Gateway can be configured to “listen” on the line for different tones and voice. The Gateway sends a “connect” signals out or
“disconnect” signaling using internet.
68
SIP Application
Case 1: Loop Start Reverse Battery :
PSTN Line was set Polarity Reverse:
The gateway can send the “200 OK” SIP signals to Billing System of ITSP, after the user pick up the Phone and detect the PSTN line answer voltage.
The gateway can send the “200 BYE” SIP signals to Billing System of ITSP, after the user hang up the Phone and detect PSTN line disconnect voltage.
Case 2: Voice Detection based on answer supervision:
PSTN Line was not support Polarity Reverse: The gateway can send the 200 OK SIP signals to
Billing System of ITSP, after the user pick up the Phone and detect the voice.
The gateway can send the 200 BYE SIP signals to Billing System of ITSP, after the user hang up the Phone and detect the hang up voice.
This type of answer supervision is not 100% accurate. Any voice frequency is detected as connect, including any intercept or recorded messages.
H.323 Application
Case 1: Loop Start Reverse Battery
PSTN Line was set Polarity Reverse:
The gateway can send the “Q.931 connect” H.323 signals to Billing System of ITSP, after the user pick up the Phone and detect the PSTN line answer voltage.
69
The gateway can send the “Q.931 Release” H.323 signals to Billing System of ITSP, after the user hang up the Phone and detect PSTN line disconnect voltage.
Case 2: Voice Detection based on answer supervision
PSTN Line was not support Polarity Reverse:
The gateway can send the Q.931 connect H.323 signals to Billing System of ITSP, after the user pick up the Phone and detect the voice.
The gateway can send the Q.931 Release H.323 signals to Billing System of ITSP, after the user hang up the Phone and detect the hang up voice.
This type of answer supervision is not 100% accurate. Any voice frequency is detected as connect, including any intercept or recorded messages.
D Sip Speeds call
Speed Call Concept:
Cut your phone number down to fewer digit dialing!
Life is moving fast - you've got to dial fast. Now you can with Speed Dial. Dial the people you call most with just dialing fewer digits instead of dialing the full phone number.
SIP Register Mode
Example: Gateway registers to sip proxy server: service.sip.com
70
What's even better is that you can customize and manage your speed dial phone numbers in
Dial Plan Setting on your gateway! Dial Plan allows you to set up to speed dial numbers that can be called with the fewer numbers.
Example 1: you want to dial any number instead of 810-any number
The destination IP address is the domain name of sip proxy server
Example 2: you want to dial 86-1111222333 instead of 810-86-1111222333
71
The destination IP address is the domain name of sip proxy server
Example 3: you want to dial 999 instead of 810-86111222333
The destination IP address is the domain name of sip proxy server
72
E Interoperability List
Gatekeeper
GnuGK openH323
Radvision ProLab GateKeeper Simulator, Version 1.0, October 2001
Clarent Gatekeeper
MediaDigm-SureKeepe
Lucent -i Merge GK
SIP Proxy Server
Vovida SIP Proxy Server
SER (SIP Express Router)
Party SIP ServerV0.5.0
Clarent SIP server
Asterisk 1.4
SXi SIP server
Gateway:
Welltek 2~8 port GW
ACCEL 2~8 port GW
Cisco 5300 and Cisco 5350 Trunk GW
Cisco ATA -186
MOSA 4 port
CISCO ATA-186
Quintum Tenor A400/A800, AS/AX Series
Antek 2500 series and vsp5004 series
Audiocodes MP-104 FXS
Clarent CPG-101 , CPG-22102Sc
D-Link 4-port gateway
BOSaNOVA Analog Gateways
Trunk Gateway:
Cisco AS5300, 5350
Clarent BHG2500
AudioCodes IPM-260 Board
IP Phone:
ACT LAN phone
TECOM IP PHONE
BCM IP Phone
Cisco 7900 IP Phone
UMEC video phone
73
F RJ21 (Telco 50) Cable and Patch Panel Install
1. General Description
Depend on customer’s requirement, there are two kinds of accessories of FXS/FXO wiring for 16 port / 24 port [
1U/19 inch Chassis
] series: RJ21 (Telco 50) cable only and RJ21 cable with patch panel. The RJ21 cable only is suitable for customers who have their own MDF (Main Distribution Frame), and the cable length is about 2.7m. The RJ21 cable with patch panel is suitable for customers who need RJ11 wiring to phone or PSTN directly, and the cable length is about 1.6m.
2. RJ21 cable wiring
The RJ21 cable consists of 25 pairs of wires for
FXS/FXO wiring (24 port
1U/19 inch Chassis
series use
24 pairs). Each wire is colored uniquely to be identified easily. Basically, the color codes are composed of 2 group of colors and the color code for each wire and pair is as the following:
Color Group
1
Color Group
2
Pair 1
Blue
White
Pair 2
Orange
Red
Green
Black
Pair 3
Brown
Yellow
Pair 4
Gray
Purple
Pair 5
Wire 1 Wire 2 Wire 3 Wire 4 Wire 5 Wire 6 Wire 7 Wire 8 Wire 9 Wire 10
Blue- White- Orange- White- Green- White- Brown- White- Gray- White-
White
Pair 6
Blue White
Pair 7
Orange White
Pair 8
Green White
Pair 9
Brown White
Pair 10
Gray
Wire 11 Wire 12 Wire 13 Wire 14 Wire 15 Wire 16 Wire 17 Wire 18 Wire 19 Wire 20
Blue- Red- Orange- Red- Green- Red- Brown- Red- Gray- Red-
Red
Pair 11
Blue Red
Pair 12
Orange Red
Pair 13
Green Red
Pair 14
Brown Red
Pair 15
Gray
Wire 21 Wire 22 Wire 23 Wire 24 Wire 25 Wire 26 Wire 27 Wire 28 Wire 29 Wire 30
Blue- Black Orange- Black Green- Black- Brown- Black- Gray- Black-
Black
Pair 16
-Blue Black
Pair 17
-Orange Black
Pair 18
Green Black
Pair 19
Brown Black
Pair 20
Gray
Wire 31 Wire 32 Wire 33 Wire 34 Wire 35 Wire 36 Wire 37 Wire 38 Wire 39 Wire 40
74
Blue- Yellow - Orange- Yellow - Green- Yellow - Brown- Yellow - Gray- Yellow-
Yellow
Pair 21
Blue Yellow
Pair 22
Orange Yellow
Pair 23
Green Yellow
Pair 24
Brown Yellow
Pair 25
Gray
Wire 41 Wire 42 Wire 43 Wire 44 Wire 45 Wire 46 Wire 47 Wire 48 Wire 49 Wire 50
Blue-
Purple
Purple -
Blue
Orange-
Purple
Purple -
Orange
Green-
Purple
The picture below shows the pair 1 to pair 5 wiring:
3. RJ21 cable with Patch Panel wiring
Purple -
Green
Brown-
Purple
Purple -
Brown
Gray-
Purple
Purple-
Gray
There are 25 RJ11 ports on patch panel, and each port is marked from 1 to 25 (24 port series use port 1 to 24).
Each port has a LED indicator on it.
The LED indicator is lighted when this port is for
FXS
functionality after system booting complete. For
FXO
port, the LED indicator is not lighted till PSTN plugged with proper polarity (RJ11 pin 4 is positive polarity).
75
G 16 port / 24 port Series module extension install
Introduce:
16 port / 24 port series, according to different module board and motherboard combine to
8/16/24 port high level gateway. The module board and types are as follows:
Motherboard Module_1 Module_2 Type
8 FXS 8 FXS module -- 16 FXS
8 FXS
4 FXS + 4 FXO
8 FXS module
8 FXS module
8 FXS module
--
24 FXS
8 FXS + 8 FXO
4 FXS + 4 FXO
8 FXO
8 FXO
8 FXS module
8 FXO module
8 FXO module
8 FXS module
--
8 FXS module
12 FXS + 12 FXO
16 FXO
24 FXO
Module group installs:
a.) Open gateway box, let cover on the fixed screws and all take off. Taking down RJ-21 (Telco
50) six angle screws going to, use six angle collets screws.
The screwdriver will be more convenient. b.) Open the top cover, there is expansion of two groups of DIN41612 model that joins the head on the motherboard. Please pay attention to two groups of triangular marks on motherboards,
Position of the mark.
76
c.)
M80x module will enclose 5 regular posts while producing the goods. Please pay attention to the position of the triangular mark on the module d.)Module 1 (the 9~6th port of FXS/ FXO) Must be put in the extension 1 area. Please insert in the extension 1 area of regular posts 5 inside in a regular hole. e.)Put and fix the module board on motherboard. Please notice the triangular mark on module and motherboard is on the same position. Please fix DIN41612 connector is regular and good, at the same time the regular post totally opens and blocks the module too.
77
f.)To the module 2 (17th ~ 24th FXS/FXO port), repeat step d and e are installed by finishing in the expanding area. g.) Open power at this moment, type shown in LCD can know module correct to install.
78
h.)Put back to the top cover, lock all screws of the top cover. Module is installed and finished.
H Gateway value Setting
Phone Volume / Line Volume
Supports user can set DSP volume.
FXO TX /RX Gain
79
Supports multiple levels of gain and attenuation for the transmit and receive paths of DAA.
1. The FXO tx gain enable gain or attenuation in 1 dB increments for the transmit from DAA site outgoing PSTN site.
2. The FXO rx gain enable gain or attenuation in 1 dB increments for the receive from
PSTN site incoming DAA site.
Note: DAA : Direct Access Arrangement.
I Scenario Application Samples
Scenario 1:
The following application was use in Multi-Office as an example
80
Scenario 2:
SVR and Gateway Setting
Part 1: SVR Setting
81
Step_1: Setting SVR Ports Number that is gateway (SVR) port 1~4.If there are other gateway registered on SVR, you can call SVR port number (100~400), or call other gateway registered number. For example, your have a gateway registered SVR number is 1001, you can call 1001 to SVR port 1 (100), or use
SVR port 1(100) to call gateway 1001.
Step_2: Select SIP Proxy Server option to setting SIP Proxy Server function. Our
SVR is a simple SIP Proxy Server, it support registered and Make call each other.
82
Setp_3: In Proxy Parameter setting, You can set SVR Port and registered time.
For example, in this setting Port is 6000 and registered Expired 900 second.
Default Proxy port is 5060.
Step_4: Setting Authentication, add account. For example, in this setting, you can
Enable/Disable authentication, if you don’t use authentication, every gateway can registered SVR. If you use authentication, you must add username/password.
Only in username /password table, you can register in SVR.
83
Part 2: Gateway Setting
Step_1: Setting Gateway Port Number, If your SVR use MD5 authentication, you must input Username/Password that on SVR authentication table to register
SVR.
Step_2: Input Server information. For example, red line cycle is must input field.
Input SVR IP address or domain name, Register Interval time setting as the same as SVR registered Expired time. If you SVR have MD5 Authentication, you must enable SIP Authentication.
84
After Setting Gateway and SVR, If your setting is right, you can call each other. you can see all registered UA and number on SVR.
Scenario 3:
SIP or H.323 Direct call Setting
H.323/SIP How to Setting Peer to Peer mode:
-Environment Setting for Demo-
Two Gateway (2/4/8/16/24 port)
Gateway Setting
Information\device Gateway_1 Gateway_2
IP Address IP:192.168.1.1 IP:192168.1.2
Port Number Port_1~Port_4:100~103
(Phone Number)
Port_1~Port_4:200~203
(Phone Number)
Attentions:
If you want to use P2P (Direct mode), please select the same
85
protocol SIP/H.323 both of the gateway. If you want to use different band gateway, please check the other band gateway have support Dialing Plan, we don’t premise all of other band gateway can complete support P2P mode.,
Setp_1:Select SIP/H.323 and setting Number
1. Choose “VoIP Basic”. Login in web interface, and in ”Advance Setting”.
2. Select you wan to use protocol (SIP/H.323).
3. Input you want to use call number.
Setp_2:Setting Dialing plan
86
For Gateway_1 Setting
1. Choose “Dialing plan” and Setting Outgoing Dial plan.
2. Setting dial plan just like picture for demo.”20x” the “x” mean wild card , it can be one of “0~9” number. And length “3~3”, when you input 3 number and the call will be made.
Destination is the Gateway_2 IP address.
For Gateway_2 Setting
1. choose “Dialing plan” and Setting Outgoing Dial plan.
2. Setting dial plan just like picture for demo.”10x” the “x” mean wild card , it can be one of “0~9” number. And length “3~3”, when you input 3 number and the call will be made.
Destination is the Gateway_1 IP address.
Step_3:make call each other
1.When you setting 2 gateway done, you can make call by each other. On gateway_1, just call “200”,and the gateway_2 Port_1 will ringing, then be made a call. And gateway_2 call
“100” , the gateway_1 will ringing, then be made a call.
87
J FXO Answer Mode
FXO Answer Mode Setting
FXO Answer Mode Concept:
When user calls the PSTN line which was connected with the FXO port, there are three answer mode for user to configure.
7. Ringing Answer Mode (Default Setting): FXO answer the call once the ring coming from
PSTN line.
8. Connecting Mode:
Case A:
“Hot Line Number” was NOT assigned in the FXO port. FXO answer the call once the ring come from PSTN line.
Case B:
“Hot Line Number” was assigned and the Hot line number belongs to remote VoIP device.
In this case, FXO port will not answer (off-hook) the PSTN till the user picks up the call.
(Note: This case can avoid charging for the Local PSTN call when the remoting VoIP devic still ring.)
Case C:
“Hot Line Number” was setting and the Hot line number was assigned to another
FXS port in same Gateway. FXO port will not answer (off-hook) till the Phone (connected to the FXS port) was picked up by user.
(Note: This case can avoid the Local PSTN charge when the FXS port still ring.)
9. Non Answer Mode: FXO will NOT answer the call in any time.
(Note: Some ITSP only let the FXO for termination function, they do not user use the FXO port for origination)
SIP Call Connecting Answer Mode
Case B:
Hot Line Number” was assigned and the Hot line number belongs to SIP device.
88
1. When the call com from PSTN to FXO, FXO start the Hot line dialing to remote SIP gateway
2. The phone of remote SIP gateway start ring.
3. When the phone was picked up, the remote SIP Gateway sends “SIP 200 OK” signal to FXO port.
4. Once FXO port receive the “SIP 200 OK” signal, FXO port would off-hook to answer the
PSTN call.
Case C:
“Hot Line Number” was setting and the Hot line number was assigned to another FXS port in same Gateway.
1. When the call com from PSTN to FXO, FXO start the Hot line dialing to FXS port.
2. The phone start ring.
3. Once the phone was picked up, FXO port would off-hook to answer the PSTN call.
H.323 Call Connecting Answer Mode
Case B:
Hot Line Number” was assigned and the Hot line number belongs to remote H.323 device.(
Note: The remote H.323 device need Disable the “Auto Answer”
)
1. When the call com from PSTN to FXO, FXO start the Hot line dialing to remote H.323 gateway
2. The phone of remote H.323 gateway start ring.
3. When the phone was picked up, the remote H.323 Gateway send “Q.931 connect” signal to
FXO port.
4. Once FXO port receive the “Q.931 connect” signal, FXO port would off-hook to answer the
89
PSTN call.
Case C:
“Hot Line Number” was setting and the Hot line number was assigned to another FXS port in same Gateway.
1. When the call com from PSTN to FXO, FXO start the Hot line dialing to FXS port.
2. The phone start ring.
3. Once the phone was picked up, FXO port would off-hook to answer the PSTN call.
90
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project