Canon imageFORMULA DR-3080CII, DR-3080CII Owner's manual
Document Scanner DR-3080CII 3. Peel off the orange tape from all the places marked ▼ below. 3. Easy Start Guide Click [Typical Installation]. [Typical Installation] installs all of the software. If you want to select which parts of the software to install, click [Custom Installation]. Thank you for purchasing the Canon DR-3080CII Document Scanner. This Easy Start Guide describes the procedure for setting up the scanner for use. Follow the procedures outlined in this Easy Start Guide to set up the scanner. Details on using the scanner are described in the User’s Guide packaged with the scanner. Before you start using the scanner, make sure to thoroughly read the User’s Guide. 4. 4. Checking the Package Contents Click [Install]. All of the currently displayed software is installed. To install only selected software, click [Back] and select [Custom Installation]. Peel off the orange tape indicated by the ▼ mark, and carefully open the upper unit. Upper Unit When you unpack your scanner, make sure all of the following accessories are included. If any of the items listed below are missing or damaged, contact your local authorized Canon dealer or service representative. 5. Click [Next]. 6. Read the software license agreement, and click [Yes] if you consent to its conditions. Remove the protective sheet. USB Cable Power Cord DR-3080CII Scanner 5. Doc um en tS ca nn er Installation of the scanner driver starts. Document Eject Guide Easy Start Guide (This Manual) Auxiliary Paper Support Plate User’s Guide 6. Gently close the upper unit. Make sure the upper unit is closed securely by pressing down on it until you hear it click into place. The DR-3080CII Setup Disc is inserted in the User's Guide. Quick Reference Guide DR-3080CII Setup Disc 7. Click [Finish] to complete the installation. Next, the installation wizard for CapturePerfect 3.0 appears. Adobe Acrobat Setup Disc 0880281099-L5T1P7-BR01 CANON CANADA INC. 6390 DIXIE RD MISSISSAUGA ON L5T Warranty Card (U.S.A and Canada only) 9Z9 Registration Card (U.S.A and Canada only) Shading Sheet 8. Click [Next]. 9. Read the software license agreement, and click [Yes] if you consent to its conditions. 10. Check the destination folder for the installation, and click [Next]. The scanner is now ready for use. Next, you need to install the scanner software. (☞STEP3) Note ● The DR-3080CII Setup Disc contains the Softwares (DR-3080CII Scanner Driver and CapturePerfect3.0) and PDF manuals. For details, refer to “About the Setup Disc” on page 16 of the User’s Guide. ● Items included in this package are subject to change without notice. ● Keep the package and packing materials for storing or transporting the scanner. Installing the Software Install the software before connecting the scanner to the computer. After checking the package contents, you need to remove all the packing materials protecting the scanner. (☞STEP2) Warning ❏ Do not connect the scanner to the computer before installing the software. In a Windows 98SE/Me/2000/XP environment, if you connect the scanner and turn it ON before you install the software, a wizard screen will appear. If this wizard appears, click [Cancel] to exit the wizard, and then turn the scanner OFF. Removing the Packing Materials After unpacking the scanner, perform the following steps to remove all the orange tape and protective materials from it. 1. Installation of CapturePerfect 3.0 starts. Peel off all the orange tape from the outer casing. Wizard Screen (Windows 2000) 11. Click [Finish] to complete the installation of CapturePerfect 3.0. 12. When all installations are complete, the installation completed screen appears. ❏ Close all other applications before installing the software. 2. Carefully open the document feed tray. 1. Log on to Windows. Be sure to log on with Administrator privileges when logging on to Windows NT/2000/XP. Document Feed Tray 2. Insert the DR-3080CII Setup Disc into the computer’s CD-ROM drive. The setup wizard automatically starts up when you insert the CD-ROM into the CD-ROM drive. If the setup wizard does not start up, run the setup.exe application on the CD-ROM. Click [Exit] to exit the installer. Click [Back] to return to the menu screen. ■ Trademarks • Canon and the Canon logo are registered trademarks of Canon Inc. in the United States and may also be trademarks or registered trademarks in other countries. • Microsoft Windows® is a registered trademark of Microsoft USA in the United States and other countries. • Other brands and product names used in this manual may be trademarks or registered trademarks of their respective companies. This completes the software installation. Next, you need to connect the scanner to your computer. (☞STEP4) PUB. CE-IE-519 ©2006 CANON ELECTRONICS INC. ☞Continued on back side ☞Continued from front side Connecting the Scanner to Your PC 6-2 Connect the scanner to your computer with the SCSI cable. SCSI cable is not supplied. Acquire a SCSI cable beforehand that matches the shape of the connectors on your SCSI card and the scanner. The scanner can be connected to a computer in two ways: by USB connection to a standard USB port on the computer, or by SCSI connection to a SCSI card installed in one of the computer’s expansion slots. Select a connection method appropriate to your computing environment. SCSI ID Dip Switches Note ● For Windows XP, a balloon help pop-up appears when installation is finished. ● The installation finished message does not appear in Windows 98SE/Me/2000. ● The scanner is registered on the computer as “CANON DR-3080CII USB” (or “CANON DR-3080CII SCSI”) in the “Imaging Device” directory of the Device Manager. ● When you restart your computer, the scan panel icon remains resident in the task tray. For details, refer to “About the scan panel” on page 35 of the User’s Guide. USB Connector Power Connector Warning ❏ When using the scanner in a daisy chain connection with other SCSI devices, pay attention to the following points: SCSI Connector (Half-pitch 50-pin, pin-type) ● The default setting for the SCSI ID is “SCSI ID=2.” Set the dip switches so that the scanner’s SCSI ID is different from all other SCSI devices on the chain. Warning ❏ Windows NT does not support the USB interface. Use a SCSI connection with Windows NT. Dip Switches ❏ Do not use both a USB connection and a SCSI connection at the same time. ❏ Use only the supplied power cord. Default Position (SCSI ID=2) ❏ Connect the scanner to your computer while the scanner is turned OFF. 1 2 ❏ Before connecting the scanner with a SCSI cable, turn your computer OFF. ON ❏ A SCSI cable is not supplied. Acquire a SCSI cable beforehand that matches the shape of the connectors on your SCSI card and the scanner. OFF SCSI ID 2 3 4 5 SW1 OFF ON OFF ON Scan Panel SW2 OFF OFF ON ON The scanner is now correctly recognized by your computer. 1. When connecting the scanner with a SCSI cable, turn your computer OFF. 2. Make sure the scanner’s power switch is in the OFF position. If the power switch is in the ON position, press the switch to turn it to the OFF position. Power Switch OFF Position ● The scanner has a built-in SCSI terminator that is permanently set to [ON]. When using the scanner in a daisy chain connection, make sure that it is connected as the terminating device and that the terminators of all other SCSI devices in the chain have been set to [OFF]. Selecting the Scanner The scanner is now connected to your computer. Next, you need to turn on the scanner and ensure Windows recognizes it. (☞STEP5) Turning On the Power (Scanner Recognition) ON Position 3. 1). Plug the power cord into the power connector on the rear of the scanner (1 4. 2). Plug the power cord into the power outlet (2 Next, you need to select the scanner with the scanning software. (☞STEP6) When you turn on the DR-3080CII in a Windows 98SE/Me/2000/XP environment, Windows uses the Plug and Play feature to recognize the scanner and automatically installs the necessary driver. (Windows NT does not have a scanner recognition feature.) You must select your scanner before using it with an ISIS- or TWAIN-compatible scanning application. The menus and procedures for selecting the scanner are different for each application. For details, refer to the manual for your scanning application when selecting the scanner. This section explains the procedure for selecting the scanner with “CapturePerfect 3.0”. For details on how to use CapturePerfect 3.0, refer to the “CapturePerfect 3.0 Operation Guide” in the Programs menu of Windows. 1. Launch CapturePerfect 3.0 from the Programs menu in Windows. 2. Select [Select Scanner] from the Scan menu. Warning ❏ When the scanner is connected by a SCSI cable, always turn on the scanner before the computer. Turning on the computer first may prevent it from recognizing the scanner properly. ❏ Be sure to log on with Administrator privileges when logging on to Windows NT/2000/XP. ❏ Wait at least 10 seconds before turning the scanner on again after turning it off. ❏ If the scanner will not be used for an extended period, be sure to unplug it from the power outlet for safety. 5. When connecting the scanner with a USB cable, use the supplied USB cable. Type A 1. Check the connection between the scanner and the computer. 2. Press the power switch to turn the scanner ON (when connecting by SCSI). The power indicator and start key indicator both light green. 3. 6. Power indicator mark facing down. 3. Select [Canon DR-3080CII] and click [OK]. Turn ON your computer. Type B Insert the plug with the The Scanner Selection dialog box appears. Power Switch Follow the steps below when connecting the scanner to your computer with a SCSI cable. On Position 6-1 Turn OFF your computer. Make sure your computer is turned OFF before connecting the SCSI cable. 4. Windows recognizes the DR-3080CII as new hardware and performs installation automatically. (Windows98/Me/2000) (WindowsXP) The setup is now complete This completes the setup of the DR-3080CII. Details on how to use the DR-3080CII are described in the User’s Guide packaged with the scanner. Before you start using the scanner, make sure to thoroughly read the User’s Guide.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project