Rite-Hite SPLT Side Rolling Door Installation/Owner's Manual

SplitSecond™
Side Rolling Door
Installation/Owner's Manual
This manual covers units: shipped after 6/20/12
For units shipped prior to 6/20/12 use Publication No. 'SplitSecondB'
Language: English (Hazards are in English and French)
The English version of this manual shall prevail over any
error in, or conflicting interpretation of, any translations.
Model: SPLT
Publication: AMEN00047 2017-03-06
SplitSecond™ Side Rolling Door Installation/Owner's ManualRite-Hite®
NOTICE TO USER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
INSTALLATION
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Mounting Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Floor Assembly (OPTIONAL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Sideframes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Header . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Leading Edge Arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Curtain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Sideframe Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Encoder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Brake Release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Thru Wall Brake Release (OPTIONAL) . . . . . . . . . . . . . . . . . . . . 17
Shroud . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Belt or Chain Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Label(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
i-COMM ii / Encoder Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Open and Close Position Adjustment . . . . . . . . . . . . . . . . . . . . 24
i-COMM ii Display Set-Up Descriptions . . . . . . . . . . . . . . . . . . . 25
Inverter (VFD) Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
575V Allen Bradley . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
OPERATION
Verify Operation of Controls Monthly . . . . . . . . . . . . . . . . . . . . .
Photoeye . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Final Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
36
36
37
37
MAINTENANCE
Rite-Hite Planned Maintenance . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wireless Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Motor Voltage Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Compact User Interface (OPTIONAL) . . . . . . . . . . . . . . . . . . . .
Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
38
39
41
42
42
45
47
PARTS
Control Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sideframe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Trolley . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Drive System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Drive Chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Drive Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parts Box – Steel Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parts Box – Fabric Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parts Box – Pharma Covers . . . . . . . . . . . . . . . . . . . . . . . . . . .
Shroud . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Curtain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Miscellaneous . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
50
52
54
55
55
56
57
57
58
58
58
59
59
60
ARCHITECTURAL DRAWINGS
Mounting Tab Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Steel Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pharma . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fabric Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
62
63
64
65
ABBREVIATION LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
2Publication: AMEN00047 2017-03-06
Rite-Hite®
Installation/Owner's Manual SplitSecond™
Side Rolling Door
NOTICE TO USER
Thank you for purchasing the SplitSecond™ door. This
reliable split-center design has a small footprint while
helping to maintain and separate different atmospheres.
• Read and understand manual before beginning
the installation, operation or servicing of this door.
• Before work begins, verify space clearance
requirements from Architectural Drawings.
• Complete "Final Checklist" on page 37
prior to leaving site.
• Store manual near door.
Rite-Hite reserves the right to substitute and/or modify
parts and drawings (electrical & architectural) from those
contained in this manual. Separate prints may be included
with the unit.
Your local Rite‑Hite Representative provides the Planned
Maintenance Program (P.M.P.) which can be fitted to
your specific operation. Contact your local Rite‑Hite
representative or Technical Support at:
(U.S.) 1‑563‑589‑2722
(S.A.) +55 21 99616 4421
NOTICE
Store dry between 40° and 80° F, [4° and 27° C].
The Rite-Hite products in this manual are covered by one or more of the
following U.S. patents: 5887385, 6145571, 6148897, 6192960, 6212826,
6321822, 6325195, 6330763, 6360487, 6481487, 6560927, 6598648,
6615898, 6688374, 6698490, 6837296, 6901703, 6942000, 6964289,
7034682, 7045764, 7111661, 7114753, 7151450, 7578097, 7699089,
7748431, 7757437, 8037921, 8167020, 8113265, 8863815, 8857498,
9222304 and may be covered by additional pending U.S. and foreign
patent applications.
Rite-Hite®, FasTrax®, FasTrax® FR, FasTrax® FR LD, FasTrax® CL,
FasTrax® XL, FasTrax® LD, LiteSpeed™, SplitSecond™, TrakLine™,
Bug-Shield™, Iso Tek®, Barrier® Glider, Dok-Dor™ are trademarks of
Rite-Hite®.
FCC Compliance
NOTE: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Recommended Parts
QTY
DESCRIPTION
PART #
1
Kit,SplitSecond Spare Parts Kit
53700722
1
Encoder
53700793
4
Fuse, .5 Amp, 600V, Time Delay (400-575V)
51000001
2
Fuse, 1 Amp, 250V, Time Delay
51000002
2
Fuse, 2 Amp, 250V, Time Delay
51000005
4
Fuse,1 Amp,600V,CC,Time Delay (208-230V)
51000023
6
Fuse, 10 Amp, 600V, CC, KLDR (400-575V)
51000033
6
Fuse, 15 Amp, 600V, KLDR (208-230V)
51000051
6
Fuse, 6 Amp, 600V, CC, KLDR (400-575V)
51000055
6
Fuse, 20 Amp, 600V, KLDR (220V)
51000077
1
Sideframe Latch
54150023
1
Photoeye Emitter (Non-Drive Interior)
63900051
1
Photoeye Receiver (Drive Interior)
63900052
1
Photoeye Emitter (Non-Drive Exterior)
63900053
1
Photoeye Receiver (Drive Exterior)
63900054
10
Sheer Pin
67850161
Special Features
i-COMM™ ii Universal Controller
Adjustable Speeds
Heavy-Duty Industrial Materials
Replaceable Seals
Obstruction Sensing System
Large Vision Area
Immediate Full Height Viewing
Powder Coated Materials
Pharmaceutical Applications
Touch-Pad Controls
Optional Stainless Steel Components
FDA and cGMP compliant
Required Tools
Fork and scissors lift
Hammer drill (cordless or electric)
Level (laser or hydro)
25ft [8m] Tape measure
Ladder 6ft - 8ft [2m - 2.5m]
Wire strippers
(Small-22 AWG [.64mm])
Utility knife
6ft [2m] Carpenter's level
Electrical Tape
Square / Straight Edge
Hammer
5/16in [10mm] Nut Driver
Plumb Bob
"C" Clamps
7/16in, 1/2in, 9/16in, 3/4in, 15/16in open end and/or socket wrench
11/16in x 12in [17mm x 305mm] drill bit for thru bolting
Straight/Philips Screwdrivers (small 1/8in [3mm] spade)
Phillips Bit and Drill Bits for Drill
1/2in [13mm] Masonry and/or drill bit for thru bolting
Allen Wrench Set (1/8in, 3/16in, 5/32in, 1/4in, 2mm)
Stainless steel mounting hardware (not provided).
NOTE: Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
• This device may not cause harmful interference.
• This device must accept any interference received, including
interference that may cause undesirable operation.
Publication: AMEN00047 2017-03-06
3
SplitSecond™ Side Rolling Door Installation/Owner's ManualRite-Hite®
SAFETY
Safety Identifications
DANGER
Indicates a hazardous situation which, if not
avoided, will result in death or serious injury.
Indique une situation dangereuse qui, si elle n’est
pas évitée, peut entraîner la mort ou de graves
blessures.
WARNING / AVERTISSEMENT
Indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
Indique une situation dangereuse qui, si elle n’est
pas évitée, peut entraîner la mort ou des
blessures graves.
Lockout Procedure
In addition to barricading the work area
and posting safety warnings, the power
supply/control must:
• Be disconnected or locked in the
OFF position using a lockout device
approved by your local codes.
• Clearly state that repairs
are being made.
• List who is responsible for the
lockout condition.
NOTE: This should be the only person who has the
ability to remove the warnings and lockout device.
• Have signage that withstand environmental conditions
(weather, wet and damp etc) and will not deteriorate or
become unreadable.
CAUTION / ATTENTION
Indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
Indique une situation dangereuse qui, si elle n’est
pas évitée, peut entraîner des blessures légères à
modérées.
NOTICE
Indicates a situation which can cause damage to the
equipment, personal property and/or the environment,
or cause the equipment to operate improperly.
NOTE: A note is used to inform you of important
installation, operation, or maintenance information.
4Publication: AMEN00047 2017-03-06
Rite-Hite®
Installation/Owner's Manual SplitSecond™
Side Rolling Door
SAFETY
General
DANGER
A qualified electrician should install the wiring in
accordance with local electrical codes.
Use lockout procedures to prevent death or severe
personal injury.
L'installation du câblage doit être effectuée par un
électricien qualifié, conformément aux normes
électriques nationales et locales.
Afin de réduire le risque de blessures graves ou
mortelles, utilisez des procédures de verrouillage.
DANGER
To reduce risk of injury or death, an earth ground
connection must be made to the green/yellow
control box ground terminal.
If metal conduit is used as the ground connector,
a ground bushing and green/yellow wire must be
properly attached to the conduit for connection to
the ground terminal, per local electrical codes.
Pour réduire le risque de blessures ou de
décès,un raccordement de terre doit être fait à la
boite de contrôle verte/jaune de la borne de terre.
Si le connecteur de terre utilisé est un conduit
métallique, un manchon de mise à la terre et un
câble vert/jaune doivent être correctement fixés
au conduit un raccordement à la borne de terre,
par codes électriques locales.
CAUTION / ATTENTION
To prevent unauthorized use, barricade the door
opening on both sides until the door has been
completely installed.
Pour empêcher toute utilisation non autorisée,
barricade l'ouverture des portes des deux côtés
jusqu'à ce que la porte a été complètement installé.
NOTICE
Failure to install conduit at the bottom of the control
box may void the warranty. The safest location for
conduit is at the bottom of the control box.
Be extremely careful when drilling conduit holes into
the control box. Drilling too deeply or allowing debris
to fall into electrical components may cause severe
equipment damage or component failure.
DO NOT turn control box upside down when drilling
holes. Holes on top of control box may allow dust
and moisture to enter the control box.
NOTICE
In freezer and cooler applications where a conduit
passes from a warm to cold temperature zone, the
conduit must be sealed with an approved material
per local electrical codes.
WARNING / AVERTISSEMENT
Failure to restrict the curtain speed can result in
damage to product or injury to personnel. The
curtain may close very quickly if the brake is
fully released.
Releasing the brake partially will allow the door to
close smoothly.
Le non-respect de restreindre le rideau vitesse
peut entraîner des dommages au produit ou
blesser le personnel. Le rideau peut fermer très
rapidement si le frein est complètement desserré.
Relâchant le frein partiellement permettra à la
porte pour la fermer sans heurts.
Publication: AMEN00047 2017-03-06
5
SplitSecond™ Side Rolling Door Installation/Owner's ManualRite-Hite®
INSTALLATION
General
Door Jamb
NOTE: Check for electrical prints included in the parts or
control box. They supersede any prints in this manual.
A
1. Alternate dimensions in brackets are in [metric].
E
F
2. Match control box serial number with sideframe
serial number.
3. Make sure you are working at the correct location and
have any required work permits.
4. Inspect the installation site to make sure that there
are no overhead obstructions (sprinkler pipes, HVAC
systems, electrical supply lines, etc.) that might
interfere with the lifting of the header assembly
during installation.
D
C
B
G
5. Detour material handling equipment (fork lift trucks,
etc.) during the installation of the door.
H
6. Make sure that the electrician is ready to bring the
correct electrical power supply to the door control box.
7. Make sure that the electrical power can be shut off
without interfering with other plant operations.
Figure 1
1. Measure Door Opening Width at the top (A)
and floor (B).
2. Measure Door Opening Height at left side (C)
and right side (D).
8. Move the entire crate of the door components as
close to the door opening as possible.
9. If multiple doors are being installed, it is imperative to
install the proper control box with the matching door
unit. The serial # for your door is on a label located on
the side of the control box and sideframe, page 22.
10. To verify proper installation, use "Final Checklist" on
page 37.
3. Dimensions from Steps 1-2 should be ± 1/2in [13mm]
of the dimensions listed on the serial number label.
If the measurements DO NOT agree, STOP! Contact
your Rite‑Hite representative.
4. Surface MUST be flat, smooth and collinear with
opposite side (E).
5. Using a 6ft [2m] carpenter's level (F), verify that the
door jambs and header are plumb and perpendicular.
11. Install Activation & Optional equipment after verifying
door operation.
6. Using a laser level (G), place a mark where the laser
is sighted on each side of the jamb to determine if
the floor is level. Measure both sides from floor to
the mark and if the floor is not level to ± 1/8in [3mm],
shim under the lower track that will be located on
the "Low Side" (H) (greatest measurement) of the
door opening.
7. 1/2 Ordered door width plus 6in [152mm] ±1/8in
[3mm] or O.D.W. plus 12in [304mm] ±1/4in [6mm]
overall (J). For space clearance requirements, see
Architectural Drawings on page 62 - 65.
B
12in
[305mm]
J
90°
Figure 2
6Publication: AMEN00047 2017-03-06
Rite-Hite®
Installation/Owner's Manual SplitSecond™
Side Rolling Door
INSTALLATION
Mounting Methods
Unacceptable Anchor Types
Acceptable Anchor Types
These anchor types provide the necessary strength for
secure attachment of the unit to the building wall.
Sleeve Anchor
Hammer Anchor
Removable Zinc Alloy
F
F
F
Stud Anchor
These anchor types are not strong enough for this
application and DO NOT provide the ability to tightly
secure the unit to the building wall.
inc Alloy & Aluminum
Z
w/Wide Head
Wedge Anchor
F
F
F
F = Length
F
Hollow Wall Anchor
(Molly Bolt)
F
Toggle Bolt
Expansion Anchor
Split Drive Anchor
Nylon w/Round Head
F
F
F
Figure 3
Length of anchor should be long enough to engage
concrete structure by a minimum of 2in [51mm]. Length
should be increased to allow anchor to extend through
any brick or aggregate fascia on exterior into concrete
structure a min. of 2in [51mm].
Conical Polyethylene
Threaded Toggle Anchor
F
Acceptable Fasteners
Threaded rod can be used and cut to length in the field to
suit the application.
Hex head bolts can be used, but length must be
determined ahead of time to ensure fasteners will work
with application.
F = Length
Figure 6
Figure 4
Wall Sleeve
3/8in [10mm] ID Ø
Back Plate
1/8in [3mm] x 6in [152mm] Ø
Figure 5
Publication: AMEN00047 2017-03-06
7
SplitSecond™ Side Rolling Door Installation/Owner's ManualRite-Hite®
INSTALLATION
Mounting Methods Continued
Concrete Wall
Block Wall
B
A
Figure 11
Steel Member
E
B
B
Figure 12
Figure 7
A. Minimum 1/8in x 6inø [6mm x 152mm] Backer Plate
(supplied by others)
Ribbed Metal Wall
J
B. Minimum Fasteners Required (supplied by others)
I
C. 3/8in [M10] for Header Bracket
D. 1/4in [M6] for Sideframe
E. Filler Board
(Ordered through Rite-Hite or supplied by others)
H
C
F. Insulation
B
Figure 8
Drywall
G. 5/16in [8mm] Minimum Steel Member
H. Drywall
I. Wall Sleeve
A
J. Corrugated Metal Siding
F
K. 2in x 6in [51mm x 152mm] or Structural Steel
Channel Backer (supplied by others)
L. Building Structural Member Angle Bracket
(supplied by others)
G
C
B
Figure 9
Insulated Panel Wall
A
G
D
B
C
Figure 10
8Publication: AMEN00047 2017-03-06
Rite-Hite®
Installation/Owner's Manual SplitSecond™
Side Rolling Door
INSTALLATION
Floor Assembly
(OPTIONAL)
You can assemble the door unit on the floor and then
attach it to the wall. To install the door directly to the wall,
see "Sideframes" instructions.
Sideframes
CAUTION / ATTENTION
Stand to the side only, when lifting the sideframe,
header or door assembly. DO NOT stand beneath,
in front, or behind the unit.
A
Se tenir sur le côté pour soulever le montant, la
traverse ou la porte. NE PAS se tenir debout sous,
devant, ou derrière l'unité.
C
B
Figure 14
Figure 13
1. Assemble unit on the floor.
C
2. Place a 10in [254mm] mark (A) at the top, center of
the opening that will be used to align the center header
tab with center of opening.
3. Stack two 2in x 4in [51mm x 102mm] boards (B)
across the ends of the fork lift, clamp header to forklift
and place header in front of the opening. Appropriate
weight limit straps may also be used to lift. Header
will be heavier on motor side, so slightly offset forklift
toward the motor side.
4. Lift unit into position:
• Plumb to within 1/4in [6mm]
• 90° to the wall
5. Secure header to wall
(see "Header" on page 10)
Figure 15
1. Place a 10in [254mm] mark (A) at the top, center of
the opening that will be used to align the center header
tab with center of opening.
2. Lift sideframes into position:
• Plumb to within 1/4in [6mm]
• 90° to the wall
3. DO NOT anchor to floor (C) until header is installed
6. Anchor sideframes to the floor.
Publication: AMEN00047 2017-03-06
9
SplitSecond™ Side Rolling Door Installation/Owner's ManualRite-Hite®
INSTALLATION
Header
A
C
J
D
Figure 16
J
1. DO NOT pinch cable (A) when installing. It may be
required to fish cable out of tubing.
2. Locate the proper mounting hardware: (4) 3/8in
[M10] bolts, nuts and lock washers (B).
NOTE: Keep header level to within 1/4in [6mm] when
placed and fastened to the wall.
3. Fasten header to the wall using the tabs (C) provided.
A minimum of three tabs need to be used (two end
tabs and the center tab).
Figure 17
NOTICE
Header MUST be installed so it does not bow.
Shim as required so as not to bend.
4. Header mounting brackets (D) are pre-installed, but
can be moved where best suited for installing to a
solid structure. The location chosen matches up with
the center shroud, if moved, the shroud may need to
be modified.
5. Before winding the curtain, connect:
a. Non-drive photoeye wires (E).
b. Drive photoeye wires and control box motor/brake
cables. Ground to sideframe.
10Publication: AMEN00047 2017-03-06
Rite-Hite®
Installation/Owner's Manual SplitSecond™
Side Rolling Door
INSTALLATION
Leading Edge Arm
D
C
B
E
F
A
G
G
Figure 19
Figure 18
1. Locate the leading edge arms (A), pivot pins (B) and
1/2in x 2 1/4in [M13 x 57mm] hex head bolts and
jam nuts (C). Install leading edge tubes into header
trolleys (D) with tension arm bracket (E) to the back of
the door.
2. Flat side of pin will face down (F). Use to adjust
leading edges side to side. (Installed at factory).
3. Adjust bolt, such that when leading edge is pulled it is
plumb (G).
4. Manually release the brake and position leading edge
arms so they are about 4ft [1.2m] apart.
Publication: AMEN00047 2017-03-06
11
SplitSecond™ Side Rolling Door Installation/Owner's ManualRite-Hite®
INSTALLATION
Curtain
D
1. Wind curtain (A) roll tube (B) (6x) per side:
B
• Right Side
Clockwise (Shown)
• Left Side
Counter-Clockwise
G
F
E
A
2. After six winds have been added, remove the strap
securing the curtain to the roll tube.
3. Pull the curtain out of the sideframe and past the
leading edge arm to remove wrinkles from the curtain.
C
Clamp the aluminum angle (C) at the end of the
curtain to the leading edge tube and fasten with the
1/4-20 BHCS [M6] (E) using the tapped holes. Top of
aluminum angle should be flush (D) with top of leading
edge tube.
4. Attach nose seal cap with longer leg (F) toward front.
Line up the pre-punched slots in the leading edge
with the tapped holes in the tube. Adjustment can be
achieved by loosening the fasteners and moving in
the slots.
E
Figure 20
5. At the top and bottom of the nose seal are two
screws (G) holding the rubber seal in place. To make
adjustments, remove screws and either raise or
stretch to lower and replace screws
6. To prevent top of curtain from being loose, an extra
strip of curtain is installed at the top. Adjustment may
be required after operation.
J
7. Fasten the tension arm to the leading edge. Door's
< 8ft [2.5M] tall, require tension arm covers (H).
8. DO NOT rotate adjustment arm past where there will
be less than 1/2in [13mm] of thread engagement (J).
K
H
9. Tighten jam nuts to prevent loosening (K).
10. Tension arm cable (L) prevents parts from falling
should an impact occur.
M
11. Sheer pin (M) may break should an impact occur.
12. Set screw (N) holds shear pin from falling out.
L
N
Figure 21
12Publication: AMEN00047 2017-03-06
Rite-Hite®
Installation/Owner's Manual SplitSecond™
Side Rolling Door
INSTALLATION
Seals
E
A
Figure 22
B
C
F
D
Figure 24
Figure 23
1. Attach right and left lintel seals (A) to header
brackets. Feed curtain into brush seal groove.
2. Ultra Seal (B): S
tandard on Pharma
Optional on non Pharma.
3. Pre-installed curtain back seal (C).
G
4. Pre-installed curtain front seal (D).
5. If optional removable seal was ordered: Unwind
curtain from the tube far enough to expose the
aluminum tube at the bottom with the hole in it
Figure 24.
H
6. Once exposed, place a bar (E) in the hole and rest up
against the corner of the sideframe.
7. Zipper (F) start point is the back of the sweep.
Figure 25
8. Using the zipper, attach (G) bottom seal.
9. If seal is too long, trim below sew line (H).
Publication: AMEN00047 2017-03-06
13
SplitSecond™ Side Rolling Door Installation/Owner's ManualRite-Hite®
INSTALLATION
Sideframe Covers
B
A
Figure 28
Figure 26
C
C
F
E
E
D
D
Figure 29
Figure 27
14Publication: AMEN00047 2017-03-06
Rite-Hite®
Installation/Owner's Manual SplitSecond™
Side Rolling Door
INSTALLATION
Sideframe Covers Continued
1. Pharma door or with Ultra seal option:
Drive sideframe seal (A).
Non-drive sideframe seal (B).
J
2. Slide top of the front cover pipe (C) over the pin on
the header.
3. Slide bottom of the front cover pipe (D) over the pin
on the sideframe bottom plate.
K
4. Install photoeye (E) in the pre-drilled hole on the front
cover, route wire and fasten with ties and clamps
provided.
G
H
L
Figure 30
5. Membrane Switch (F).
6. Locate the center pipe, place top end around pin, lift
and place over pin at the bottom (G).
7. Slide pre-installed pipe on fabric cover (H) over pins
at the front edge.
8. Stretch fabric cover around center pipe, around to the
back and attach fabric cover to sideframe using hook
and loop fastener (J).
9. Rear sideframe seal (K) is factory installed.
10. Front seal (L) is attached to the fabric sideframe.
Publication: AMEN00047 2017-03-06
15
SplitSecond™ Side Rolling Door Installation/Owner's ManualRite-Hite®
INSTALLATION
Encoder
B
A
Figure 31
1. Locate encoder cable (A) at the top of the drive
sideframe and route to encoder.
2. Place encoder onto drive shaft with connector toward
bottom and center of door. Tighten lock collar set
screw (B) [2mm] to 14in/lbs [1.5N-m].
Brake Release
D
C
Figure 32
1. Steel Sideframes (C): Uncoil steel cable that is
pre-attached to the brake handle.
Route cable down inside sideframe and attach to the
brake release handle.
Figure 33
2. Attach cable end to brake release arm (D).
To release brake, lift up on brake release handle.
If handle does not release brake, adjust cable at the
top, by loosening bolts and adjusting cable.
Fabric Sideframe (C): Uncoil cord and let hang.
16Publication: AMEN00047 2017-03-06
Rite-Hite®
Installation/Owner's Manual SplitSecond™
Side Rolling Door
INSTALLATION
Thru Wall Brake Release
(OPTIONAL)
Shown without wall or door in place.
A
D
B
C
A. Handle Bracket
B. Conduit
C. Door Mounted Side
Brake Release Cable
D. Release Pulley
E. Release Handle
E
Figure 34
1. To release the brake, rotate the handle.
2. As curtain nears the top, allow to slow down so it
does not overtravel.
Publication: AMEN00047 2017-03-06
17
SplitSecond™ Side Rolling Door Installation/Owner's ManualRite-Hite®
INSTALLATION
COMPLETE 'Shroud' AND 'Adjustments' AFTER DOOR IS OPERATIONAL
Shroud
Belt or Chain Adjustments
Painted Flat Shroud
Painted Doors only
B
G
F
C
D
A
Figure 37
Stainless Steel Doors only
Figure 35
Stainless Steel Sloped Shroud
H
E
Figure 38
Figure 36
1. Header mounting brackets (A) are pre-installed, but
can be moved where best suited for installing to a
solid structure.
2. Notches (B) only on painted shrouds.
3. Install center shroud (C) using self/tap and drill
screws in pre-drilled holes provided.
J
Figure 39
4. Install drive shroud (D).
5. Install drive and center shroud using 1/4in -20 [M6]
fasteners in holes provided (E).
So there is no more than 1/4in [6mm] sag, adjust:
–– Chain (F) with turnbuckle chain tensioner (G), or
–– Belt (H) with belt tensioner (J)
18Publication: AMEN00047 2017-03-06
Rite-Hite®
Installation/Owner's Manual SplitSecond™
Side Rolling Door
INSTALLATION
Label(s)
12in
[305mm]
A
5ft
[1524mm]
A
Figure 40
1. Clean surface where label (A) is to be placed.
2. Peel off backing on label and apply in position.
Publication: AMEN00047 2017-03-06
19
SplitSecond™ Side Rolling Door Installation/Owner's ManualRite-Hite®
INSTALLATION
Electrical
! DANGER
A qualified electrician should install the wiring in
accordance with local and national electrical codes.
Use lockout and tagout procedures to prevent
death or severe personal injury.
Un électricien qualifié doit installer le câblage
conformément aux codes électriques locaux et
nationaux.
Utilisez procédures de cadenassage et d'étiquetage
d'interdiction pour éviter des blessures graves
ou la mort.
! DANGER
To reduce risk of injury or death, an earth ground
connection MUST BE made to the green/yellow
control box ground terminal.
If metal conduit is used as the ground connector,
an N.E.C. approved ground bushing and green/
yellow wire MUST BE properly attached to the
conduit for connection to the ground terminal.
Pour réduire le risque de blessure ou de décès, une
connexion de mise à la terre doit être faite au vert/
jaune borne de masse du boîtier de commande.
NOTICE
Failure to install conduit at the bottom of the control
box may void the warranty. The safest location for
conduit is at the bottom of the control box.
Be extremely careful when drilling conduit holes into
the control box. Drilling too deeply or allowing debris
to fall into electrical components may cause severe
equipment damage or component failure.
DO NOT turn control box upside down when drilling
holes. Holes on top of control box may allow dust
and moisture to enter the control box.
NOTICE
In freezer and cooler applications where a conduit
passes from a warm to cold temperature zone, the
conduit must be sealed with an approved material per
300.7(a) of the National Electric Code (NFPA 70).
NOTICE
The first time that the door system is operated, it may
move in the wrong direction if the incoming power
phase is reversed. Be prepared to turn the disconnect
switch off if the door begins closing instead of opening.
Si conduit métallique est utilisé comme le
connecteur de mise à la terre, un N. E. C. sol
approuvé la bague et fil vert/jaune doit être
correctement relié à la conduite à la borne de
connexion de terre.
20Publication: AMEN00047 2017-03-06
Rite-Hite®
Installation/Owner's Manual SplitSecond™
Side Rolling Door
INSTALLATION
Electrical
1. It is the responsibility of the end user to provide
electrical service up to the control box with proper
branch service protection and an approved means of
disconnect.
Continued
2. All control boxes should be mounted on the warm
side regardless of door mount side.
3. Mount the control box on a wall adjacent to the door
at approximately 54in [1.3m] above the floor level.
54in [1.3m]
4. The incoming power terminals in the control box will
not accommodate wires larger than 12AWG. 20 or 30
Amp service may be required for cable runs longer
than 300ft [91,000M].
5. The control box is provided with class CC protective
fusing for the incoming power.
Figure 41
NOTE: Local electrical codes may require the use of
rigid conduit, rather than flexible conduit. If required,
remove the control cables from the furnished flexible
conduit, install the rigid conduit in its place and
rewire. Make sure to remove and replace the conduit
connector in the bottom of the control box.
6. DO NOT splice wires.
7. Drill a hole for the power supply cable (by others)
in the bottom of the control box using the proper
connection to maintain the NEMA rating on the
enclosure. Incoming 3-phase power must connect into
fuse holder terminals F1, F2, and F3. Ground must
attach to the green/yellow terminal. All holes drilled
through the control box must be through the bottom
of the box.
B
A
C
8. Route all field installed wires so that separation is
maintained between line voltage wires and low voltage
class II wiring. Electrical prints included in the control
box supersede any prints included in this owners
manual. Always check parts or control box for prints.
A. Membrane
B. Photoeye Connections
C. Conductive Tape
Publication: AMEN00047 2017-03-06
Figure 42
21
SplitSecond™ Side Rolling Door Installation/Owner's ManualRite-Hite®
INSTALLATION
Electrical
D8
FINAL ASSEMBLY
7802E009/11
-
3
4
Continued
B
NEXT ASSEMBLY
5
6
7
A
7
5
6
C
E
4
3
R
D
R
G
G
CR1 CR3
CR1 CR3
X1
X2
N.O.
3
(OPEN BUTTON)
4
X1
N.O. 3
X2
4
OV A1 10V A2
(OPEN BUTTON)
OV A1 10V A2
6mm
!
CLASS II LOW VOLTAGE ONLYCLASS
II LOW VOLTAGE ONLY !
6mm
B1
10mm
Loop sens. Adj.
Freq. Adjust
8
1 min to
Act / Pass
Relay A,B
ASB
Relay A Pres. / pulse
Relay A Entry / Exit
Relay B Pres. / pulse
Relay B Entry / Exit
Pulse 100ms / 500ms
Not Used
10
APEMs
ON
1 2 3 4 5 6 7 8 9 10
L1 L2 L3
Detect
Loop sens. Adj. Pres. Time Adj.
B5 B3B6 B4B7 B5 B6 B7
B4
B1 B2
10
RE BKWY
Power
9
9
8
Freq. Adjust
8
8
Act / Pass
Relay A,B
ASB
Pres. / pulse
Relay A
Entry / Exit
Relay A
Pres. / pulse
Relay B
Entry / Exit
Relay B
Pulse 100ms / 500ms
Not Used
7
SAFETY
7
CLSG
0V
10
BKWY
10
Pres. Time Adj.
1 min to
T4 T2 T5T3 T6T4 T5 T6
T3 T1
B3
Detect
3 208-240V, 460-480V, 575V
3 208-240V, 460-480V, 575V
NO
DELAY
DELAY
COM NO NC
F2
F1
F3
F4
ON
F4
H2
PE
H3
H4
F7
F5
H3
H2
H1
H4
T1
F7
F5
1 2
12-24VAC/DC
POWER
USE CLASS CC
FUSES ONLY
RATED 600V, 30A
F3
PE
H1
T1
HIGH VOLTAGE ONLY !
COM NO NC
X3
X2
X1
12-24VAC/DC
ON
1 2
LEARN
LEARN
ACT
10RD433
HOLD
TIME
NO
DELAY
DELAY
LEARN
ACT
LEARN
10RD433
HOLD
TIME
T3
POWER
T2
12-24V
AC/DC
COM
NO
NC
T1
USE CLASS CC
FUSES ONLY
RATED 600V, 30A
F2
+
PE
GND
GND
GND
U
V
W
STB
N
N
BRK
B
T3
T2
T1
PUL | TOG
0.5s | 10s
L3
12-24V
AC/DC
COM
NO
NC
L2
F1
-
USE CLASS CC
FUSES ONLY
RATED 600V, 30A
GND
GND
GND
U
V
W
STB
N
N
BRK
L1
PUL | TOG
0.5s | 10s
L3
L2
L1
USE CLASS CC
FUSES ONLY
RATED 600V, 30A
PE
+
-
(DISCONNECT SWITCH)
W
W
V
U
L1 L2 L3
1 2 3 4 5 6 7 8 9 10
(DISCONNECT SWITCH)
V
U
APEMs
ON
Power
T2
B2
RS 485
RS 485
6
5
COM
Remote
Pairing
9
RE
9
5
WIRELESS HOST
4
6
3
RF Com
Fault
24V
2
8
8
4
CLSG
3
7
7
0V
ACTIVATOR
POWER
1
2
OPEN CLS STOP O/C
6
5
6
COM
24V
5
1
4
SAFETY
4
O/C
WIRELESS HOST
3
POWER
3
STOP
Fault
2
Remote
Pairing
2
CLS
RF Com
1
C
ACTIVATOR
1
- PLC LOGIC INPUTS & OUTPUTS ON PLC
OPEN
- PLC LOGIC INPUTS & OUTPUTS ON PLC
T1
10mm
HIGH VOLTAGE ONLY !
X2
X3
575V CONFIGURATION
220V 1 CONFIGURATION
H
USE CLASS CC
USE CLASS CC
FUSES ONLY
RATED 600V, 30A
FUSES ONLY
RATED 600V, 30A
F3
F
F7
F4
USE CLASS CC
USE CLASS CC
FUSES ONLY
RATED 600V, 30A
FUSES ONLY
RATED 600V, 30A
575V CONFIGURATION
F1
208/230/460V
F2
F3
J
E
F7
F4
Remove labels after installation is complete
U
V
W
STB
N
N
BRK
XX4
XX1
XH2
XH1
CONFIGURATION
F2
GND
GND
GND
U
V
W
STB
N
N
BRK
0V 1
F1
X1
DO NOT DRILL!
INCH TOLERANCES
+
UP TO
OVER
A
220V
USE CLASS CC
FUSES ONLY
RATED 600V, 30A
USE CLASS CC
FUSES ONLY
RATED 600V, 30A
F7
USE CLASS CC
FUSES ONLY
RATED 600V, 30A
F1
F2
F3
VERIFY THAT THIS DRAWING HAS NOT BEEN SUPERCEDED BY NEWER REVISION. ABOVE APPLIES
ONLY WHEN DRAWING IS CURRENT.
F4
2. The red Disconnect Switch (B) stops door operation.
The control is rotated to the "ON" position for normal
door operation. To stop door operation rotate the
control to the "OFF" position. Whenever the door
6 disconnect switch,
7
operation
is stopped by using the
you must do the following to resume operation.
a. Rotate the red disconnect switch to the "ON" position.
b. Press the "OPEN/RESET" button to reset and open
the door.
3. The i-COMM (C) is used to control all door functions.
PRIOR
0.0
0.0
0.0
0.0
0.0
0.0
0.1
0.1
0
0.125
0.25
1.25
5
15
40
80
0.125
0.25
1.25
5
15
40
80
-
ANGLES
FINISH
+/- 1 DEG
THIS DRAWING COVERS DOORS
CONFIGURED AFTER 06/18/2012
F7
1. The green button (A) opens and resets the door after
a
6 The
7 and release the button.
8 fault. To "OPEN", press
i-COMM will automatically close the door after the
preset time has expired.
F4
U
V
W
STB
N
N
BRK
XX4
XX1
XH2
XH1
F3
GND
GND
GND
U
V
W
STB
N
N
BRK
F2
DO NOT DRILL TOP OR SIDES OF ENCLOSURE,
ALL FITTINGS TO BE INSTALLED ON THE
SCOPE
BOTTOM OF ENCLOSURE.
N/A
C 2012
RITE-HITE
R
DOORS INC.
(D)5 inside
4. Label
control box that4 is a ready reference 3
to the i-COMM inputs and outputs, page 23
COVERS DOORS
THIS DRAWING
5. Red Bold solid line (E) indicates un-safe
area
for
CONFIGURED AFTER 06/18/2012
drilling holes
SCOPE
NEWER REVISION. ABOVE APPLIES
VERIFY THAT THIS DRAWING HAS NOT BEEN SUPERCEDED BY
ONLY WHEN DRAWING IS CURRENT.
6. Green Bold dashed line (F) indicates
N/Asafe area for
drilling holes
4
7. 5Serial # label (G).
OVER
INCH TOLERANC
UP TO
0
0.125
0.25
1.25
5
15
40
80
0.125
0.25
1.25
5
15
40
80
-
ANGLES
FINISH
+/- 1 DEG
PRIOR
C
2012
RITE-HITE
R
DOORS INC.
3
8. F1, F2, F3 incoming power terminals for
230/460/400/575V 3Ø Configuration (H).
9. DO NOT wire incoming power into these terminals (J).
22Publication: AMEN00047 2017-03-06
Rite-Hite®
Installation/Owner's Manual SplitSecond™
Side Rolling Door
INSTALLATION
i-COMM ii / Encoder Setup
Logic Chart
Publication: AMEN00047 2017-03-06
23
SplitSecond™ Side Rolling Door Installation/Owner's ManualRite-Hite®
INSTALLATION
i-COMM ii / Encoder Set-Up Continued
MUST complete before operating door.
Encoder Set-Up Instructions
Before beginning the encoder adjustments, manually
move the door to either the open or close position. Verify
all wiring to the encoder is terminated as shown on the
electrical drawings included in the control box. If motor
rotation (phase sequence) is changed during this setup,
restart this procedure from the beginning.
1. Power up the door, and press the enter button to
enter the "MAIN MENU".
2. Using the down button, scroll to the parameter named
"Open Distance".
3. Press the enter button to view the value of this
parameter. The unit of measure on this parameter
is feet.
The optimum value for this parameter is door opening
width minus 1ft [305mm]. Change the value using the
up and down buttons, round down if required. When
parameter is changed press enter to return to the
"MAIN MENU".
If door is in OPEN position use steps 4 -7.
If door is in CLOSE position use steps 8-11.
4. Scroll using the down button to the item named "Set
Open Pos.".
5. Press the enter button to view this parameter. The
controller will display the following message "RESET
ALL LIMITS" … "Press Up to Start". Pressing the
up button will reset all of the limits, and reboot the
controller.
NOTE: DO NOT use this menu item to make
adjustment to the limits; this is only for initial setup.
6. Press the Open/Reset button on the control box. The
door should begin to time out and then close. Since
motor rotation may need to be changed, be ready to
shutdown the door if it begins to move in the wrong
direction.
If motor rotation is changed, begin again at step #1.
7. If rotation is correct proceed to the instructions for
adjusting the open and close positions.
STOP! Steps 8-11 for CLOSE position ONLY.
8. Scroll using the down button to the item named "Set
Close Pos.".
9. Press the enter button to view this parameter. The
controller will display the following message "RESET
ALL LIMITS" … "Press Up to Start". Pressing the
up button will reset all of the limits, and reboot the
controller. NOTE: DO NOT use this menu item to
make adjustment to the limits; this is only for initial
setup.
10. Press the Open/Reset button on the control box. The
door should begin to open. Since motor rotation may
need to be changed, be ready to shutdown the door
if it begins to move in the wrong direction. If motor
rotation is changed, begin again at step #1.
11. If rotation is correct proceed to the instructions for
adjusting the open and close positions.
Open and Close Position Adjustment
To adjust the OPEN position:
1. Power up the door, and press the enter button to
enter the "MAIN MENU".
2. Using the down button, scroll to the item named
"Open Pos. Adjust".
3. Press the enter button to view the value of this
parameter. This parameter will show a coded value
on the left and the opening width in inches on the
right. This value will always be less than the door
opening width.
To open the door more, adjust this value to be less
than the current value. To open the door less, adjust
this value to be more than the current value. (i.e. If
the current value is 72.0in [1.8M], to open the door
4in [102mm] more, change the value for "Open Pos.
Adjust" to be 76in [1.9M]).
Changing this value will not affect the close position.
Change the value using the up and down buttons.
4. When parameter is changed press enter to return to
the "MAIN MENU".
5. Scroll using the down button to the item named "Exit
[Enter]".
6. Test door operation and continue adjusting as
required.
To adjust the CLOSE position:
1. Power up the door, and press the enter button to
enter the "MAIN MENU".
2. Using the down button, scroll to the item named
"Close Pos. Adjust".
3. Press the enter button to view the value of this
parameter. This parameter will show a coded value
on the left and relative change in inches on the right.
When entering this parameter the value will always
start at 0.0.
To bring the curtain leading edges closer together,
adjust this value so that it is less than zero (i.e. To
close the door 4in [102mm] more, the value for
"Close Pos. Adjust" will be - 4in [102mm]). Moving
this parameter in the positive direction separates the
leading edges. Changing this value will not affect the
open position.
Change the value using the up and down buttons.
NOTE: If you leave this parameter and return to
it, its value will again be zero. Any changes made
before leaving the parameter will still be effective.
For example: If you lowered the door 4in [102mm],
leave the parameter and return, the parameter will
display 0.0 Even though the display shows 0.0 the -4in
[102mm] change has been recorded.
24Publication: AMEN00047 2017-03-06
Rite-Hite®
Installation/Owner's Manual SplitSecond™
Side Rolling Door
INSTALLATION
i-COMM ii Encoder Set-Up
Continued
4. When parameter is changed press enter to return to
the "MAIN MENU".
5. Scroll using the down button to the item named
"Exit [Enter]".
TIP: At any point in the menu mode, Pressing and
holding the enter button for at least 2 seconds will
cause the controller to automatically accept all the
changes made and exit the menu system.
6. Test operation of the door, and continue adjustment
as required.
i-COMM ii Display Set-Up Descriptions
Option
Description
Open Distance
Use this option to set the overall opening distance of the door (in feet). For example, for an 8ft [2438mm]
wide SplitSecond. This option should be set to 7ft [2133mm]. This measurement is used for initial position
setup only. For small adjustments of the open and close position, use "Close Position Adjust"
or "Open Position Adjust".
Set Close Pos
Use this option for initial position setup. Manually place door in the close position and select this option.
Alternatively "Set Open Pos." can be used if it is more convenient to place the door in the open position.
NOTE: This option approximately sets the open and close positions. For additional adjustment of the
open and close position, use "Close Position Adjust" or "Open Position Adjust".
Set Open Pos
Use this option for initial position setup. Manually place door in the open position and select this option.
Alternatively "Set Close Pos." can be used if it is more convenient to place the door in the closed position.
NOTE: This option approximately sets the open and close positions. For additional adjustment of the
open and close position, use "Close Position Adjust" or "Open Position Adjust".
Open Pos Adjust
Use this option to make small adjustment to the open position. The number displayed is the
measurement between the open and closed position. For example if this option was set to 100in
[2540mm] the door would open 100 in [2540 mm] from the closed position. It is recommended to adjust
the closed position of the door first, before adjusting the open position.
Close Pos Adjust
Use this option to make small adjustment to the closed position. The number displayed is the relative
displacement of the closed position. For example, if this option was set to -1.0in [-25mm] the door would
close approximately 1.0in [25mm] more. If this option was set to 2.0in [51mm] the door would close
2.0in [51mm] less.
Apr Open Pos
Use this option to adjust the approach open position. This option is a measurement in inches from the
open position. For example, if this option was set to 24.0in [610mm] the door would slow down 24.0in
[610mm] from the open position.
Encoder Startup
The controller is waiting for valid data from the encoder. It the controller does not receive a response at
startup, this will remain on the screen indefinitely. If this does not clear with 5 seconds, please check all
encoder wiring.
Encoder Read
The controller is unable to read valid data from the encoder. Check all wiring and M12 cable connections.
Ensure that the shield on the encoder cable is connected to ground, and that the control box is grounded.
The error requires the power to be cycled to reset.
Encoder Velocity
The controller has received a signal from the encoder that the door is moving faster than allowed. This
can occur if the encoder is not properly attached to the shaft (check set screw on encoder collar), bad
electrical connection to the i-COMM, or improper grounding. The error requires the power to be cycled to
reset.
Open Time Limit
Door tried to run, but did not reach the open or close position within 8 seconds.
Photoeye (PE) Failure
Non-Drive PE's must have green light on, drive PE's must have orange & yellow lights on. Check for
alignment & power to each.
SPLT120515
Publication: AMEN00047 2017-03-06
25
Open Time Limit
Menu Interrupt
Limit Failure
Emergency Stop
Close Time Limit
Limit Pulse Time
Obstruction
System Clk Read
3
4
5
6
7
8
9
10
Photoeye Failure
Encoder Read
Encoder Velocity
Encoder Connection
VFD Trip # xxx
VFD Comm. Loss
Program Inverter
Check Reversing Edge
Refeed Curtain
Encoder-No Power
14
15
16
17
18
19
20
21
22
PRO System
13
12
Unknown State
Breakaway
2
Door
Faulted
Normal Power Up
11
Indicates the board watchdog timer has reset
Watchdog Timer
0
1
i-COMM ii has detected no power to encoder error
i-COMM ii has detected a curtain refeed error
i-COMM ii has detected a reversing edge continuity
error
Inverter is not programmed for proper door operation
i-COMM ii has lost communication with inverter
Inverter is in fault. xxx Indicates the active inverter
fault
i-COMM ii has detected a connection error
i-COMM ii has detected a velocity error
i-COMM ii has detected a bad encoder read
Indicates problem with reversing photoeye's
(FSTX Series, LTSPD or SPLT)
Pro inverter fault (8000, 8000XL)
State unknown
System clock failed
Door has detected obstruction and reversed 3 times
Trakline limit problem. Second close limit pulse not
detected.
Run close time limit exceeded
E-Stop button pushed or overload relay tripped
(8900) or Inverter relay failure (8600) or chain hoist
switch open (FasTrax)
Limit switch has failed
i-COMM menu interrupted
Run open time limit exceeded
Door is in breakaway mode: FasTrax - chain hoist;
8000CL/XL - lower track or sideframe door; 8000/CL/
XL overload relay
Indicates loss of power
REASON / FAULT MESSAGES
TOP
DISPLAY
I-COMM BOTTOM DISPLAY
FAULT ERROR DESCRIPTION
FAULT
CODE
Service Required
Jog to Close
Jog to Close
Service Required
Check Connection
Push Open/Reset
Service Required
Service Required
Service Required
Jog to Close
Check Inverter
Service Required
Service Required
Inspect & Reset
Service Required
Service Required
Push Open/Reset
Service Required
Push Open/Reset
Service Required
Reset/Jog Door
Push Open/Reset
Service Required
ACTION REQUIRED
LCD Display Messages
i-COMM board has detected no power to the encoder.
Check wiring connections
LiteSpeed header Slack Sensor photoeye has tripped curtain has reversed 5 times
Check reversing edge wires for continuity or if shorted.
Indicates inverter (VFD) is not properly programmed. Reprogram inverter.
i-COMM board has lost communication with inverter
(VFD). Check wiring connections
i-COMM board displaying inverter (VFD) fault. Check
manual for inverter faults
i-COMM board did not read connection to encoder. Check
wiring connections
i-COMM board detected improper speed or wrong
direction. Check wiring connections
i-COMM board did not read encoder status. Check wiring
connections.
Reversing photoeye's did not pass test
Check inverter for fault codes
Cycle power and reset
Clock has elapsed, check and/or replace battery
Door tried to close 3 times but sensed friction or an
obstruction, reversed, stayed open and faulted.
Check limit switch
Door didn't reach close limit before 8 seconds
E-Stop button was activated or is defective. Check 8900
overload relay, check chain hoist switch on FasTrax series
model doors. Press Open/Reset button to operate door.
Door did not read limit switch or two switches activated
simultaneously
The i-COMM menu was accessed. Press Open/Reset
button to operate door.
Door did not reach open limit before 8 seconds
If need be - press Open/Reset to "Jog" door. Reset
breakaway mechanism. Press Open/Reset button to
operate door.
Power to the door was lost, press Open/Reset button to
operate door
i-COMM board requires replacement
ACTION REQUIRED:
REASON / TASK
SplitSecond™ Side Rolling Door Installation/Owner's ManualRite-Hite®
INSTALLATION
i-COMM ii / Encoder Set-Up Continued
26Publication: AMEN00047 2017-03-06
Publication: AMEN00047 2017-03-06
Curtain Jam
Counterweight
27
28
I-Zone active (overrides timer display)
Photoeye is blocked (overrides timer display)
Indicates door is waiting for normal close command
Door is closing
Displays cycle count
Door is interlocked and cannot be opened
I-Zone Detection
Photoeye Blocked
Waiting for CMD
Door Closing
Cycles: xxxxxx
Interlock Active
Door
Stopped
Door
Closed
Door is stopped
Displays closing time in seconds
Closing in xx secs
Push Open / Close
Indicates activation on (overrides timer display)
Activation On
Stand
Clear
When in preannounce to close
None
Door is opening
No Fault
When not in preannouce to close
Blank
255
i-COMM ii has detected a door overtravel error
None
Door Overtravel
33
Curtain is moving slower than expected while opening
Door is
Open
Curtain Jam
32
i-COMM ii has detected a low velocity open error
None
Low Velocity
31
i-COMM ii has detected a low velocity close error
i-COMM ii has detected a counterweight opening
error
i-COMM ii has detected a counterweight closing error
Curtain is moving slower than expected while closing
i-COMM has detected that the door CUI is locked
i-COMM has detected reversing edge was activated
(CE only)
VFD Relay failed to change state
i-COMM ii has detected an LZR test error
REASON / FAULT MESSAGES
Door is
Opening
Low Velocity
30
Counterweight
Door Locked
26
29
Reversing Edge Count
25
Door
Faulted
VFD Torque Relay
24
I-COMM BOTTOM DISPLAY
FAULT ERROR DESCRIPTION
LZR Test Failed
TOP
DISPLAY
23
FAULT
CODE
Open/Close door
Service Required
None
None
Action Required
Service Required
Service Required
None
Action Required
None
None
None
None
Service Required
Service Required
Service Required
Service Required
Service Required
Service Required
Service Required
Door Locked
Jog to Close
Service Required
Jog to Close
ACTION REQUIRED
LCD Display Messages
Give command to close or open door
Verify interlocked door is closed
None
Door is in process of closing
Give command to close door
Inspect reversing photoeyes on the door
Inspect I-Zone sensors
160227
Reclose timer is counting down and will close the door
A activation device is holding the door open
Door is open and getting ready to close
Door is open, waiting to close
An activation command to open door was given
None
FSTX XL curtain has traveled past the curtain sensing
photoeyes
Check for drive system obstruction or high wind load
Wind or pressure on curtain has caused FSTX XL door to
open slower than normal
Wind or pressure on curtain has caused FSTX XL door to
close slower than normal
Check counterweight photoeyes and verify counterweight
travels freely in the tube
Check counterweight photoeyes and verify counterweight
travels freely in the tube
Check for drive system obstruction or high wind load
Press and hold the Red button on CUI for 15 seconds to
unlock
Cycle power and reset
Check torque setting and check VFD relay
Check wiring of LZR or perform "Teach In" per BEA User's
Guide
ACTION REQUIRED:
REASON / TASK
Rite-Hite®
Installation/Owner's Manual SplitSecond™
Side Rolling Door
INSTALLATION
i-COMM ii / Encoder Set-Up Continued
27
M
C
Component Key:
A
Power LED
D
B
Contrast Button
C
Up Button
E
D
Enter Button
E
Back Button
F
Down Button
G
LED Input's X0 - X15
H
Encoder Terminals
I
Input Terminals
J
DC Terminals
K
OV Terminals
L
J4 Connector
M
Output LED's K0-K2
& Y0-Y5
N
Display
O
Battery (CR2032 3V)
P
SD Card
F
G
H
I
J
K
Installation/Owner's ManualRite-Hite®
B
SplitSecond™ Side Rolling Door A
INSTALLATION
L
i-COMM ii / Encoder Set-Up Continued
Layout
P
N
Rev. 090814
28Publication: AMEN00047 2017-03-06
O
Rite-Hite®
Installation/Owner's Manual SplitSecond™
Side Rolling Door
INSTALLATION
i-COMM ii / Encoder Set-Up Continued
Procedures
Programming Folders
Adjusting Reclose Timer:
Use the Enter, Up, Down, Back buttons on the i-COMM ii
to navigate through the folders. To exit system, use back
button until “Door Faulted” appears.
1. Press ENTER button.
2. Use UP button to scroll to "TIMER FOLDER", press
ENTER, should display “Set Close Timer”.
Encoder Folder
3. Press ENTER button.
See Folder Layout Chart to change / view settings.
MUST perform encoder setup for door operation.
4. To increase reclose time, press UP button.
I/O Setup Folder
6. Press BACK button when complete.
See I/O Setup Layout Chart to change / view settings.
Use to setup Input and Output functions
Setting Clock:
Timer Folder
See Timer Layout Chart to change / view settings.
Use to change reclose or preannounce timer.
General Folder
5. To decrease reclose time, press DOWN button.
1. Press ENTER button.
2. Use UP button to scroll to "GENERAL FOLDER",
press ENTER, should display “Clock”.
3. Press ENTER button, should display M/D/Y and time.
See General Layout Chart to change / view settings.
Use to setup Clock, Maintenance cycles
4. Press UP, set year - press ENTER, set month - press
ENTER, set day - press ENTER, set hour - press
ENTER, set minute - press ENTER.
View Folder
5. Press BACK when complete.
See View Layout Chart to change / view settings.
Use to view cycle count, fault history, door information.
Setting Maintenance:
Load / Save Folder
See Load / Save Layout Chart to change / view settings.
See Legal information.
Use for programming.
Inverter Folder
See Inverter Layout Chart to change / view settings.
Use to change door speeds, torque settings.
1. Press ENTER button.
2. Use UP button to scroll to "GENERAL FOLDER", press
enter, press UP to scroll to "Maint. Months" or "Cycles".
3. Press ENTER button, should display number of
months or number of cycles.
4. Press BACK when complete.
hen setting Maintenance timer:
W
Open / Reset button will flash slow when set time / cycles
have expired and display Maintenance Required.
o reset Maintenance light (flashing Open / Reset button):
T
Press ENTER button, scroll to "GENERAL FOLDER",
press ENTER button, scroll to "Reset Maintenance", press
ENTER, then UP to start, then green Open Button.
Checking Fault History:
1. Press ENTER button.
2. Use UP button to scroll to "VIEW FOLDER", press
ENTER, should display “Fault History”.
3. Press ENTER button, should display the last fault /
flash the date / time it occurred.
4. This displays the last 20 faults with date and time.
5. Press BACK when complete.
Publication: AMEN00047 2017-03-06
29
SplitSecond™ Side Rolling Door Installation/Owner's ManualRite-Hite®
INSTALLATION
Inverter (VFD) Programming Continued
ENCODER FOLDER
TIMER FOLDER
I/O SETUP FOLDER
Folders
230/460V – Error Codes
#*
NAME
VALID VALUES
DESCRIPTION
VALUE
0
Open Distance
3-24
Used to Set Opening distance for door
8
1
Motor Drive Side
Right Drive/Left Drive
Used to select motor drive side.
-
2
Set Close Pos.
Press UP to Start
Use for initial setup of close position
-
3
Set Open Pos.
Press UP to Start
Use for initial setup of open position
-
4
Close Pos. Adjust
±100.0
Use to adjust close position. Relative to current close position
0.0
5
Open Pos. Adjust
0 - 999.00
Use to adjust door open position
-
6
Partial Open Pos.
0 - Open Pos. Height
Use to adjust door partial open position
-
7
Encoder Position
0-01FFFF
Current encoder position
-
8
Encoder Baud
125,220,433-A,433-B kbps
Used to select encoder data rate
433-A kbps
9
Appr. Open Pos
0.0 - 100.0
Approach Open Position
28.0
10
Appr.Close Pos.
0.0 - 100.0
Approach Close Position
-
11
Set Open PB Func.
Auto Close Mode, Tog & Auto Close,
Reset/Jog Only, Toggle Mode
Use to select the function of the Open/Reset Button.
Auto Close Mode
12
Set Loop Func.
Auto Close Mode, Reversing/Hold
Open
Use to select the function of the induction loop input
Auto Close Mode
13
I-Zone System
Enabled/Disabled
Use to Enable/Disable the I-Zone detection system
Disabled
14
Output Def. YK0
0-35 (See Table)
User configurable relay
0
15
Output Def. YK1
0-35 (See Table)
User configurable relay
20
16
Output Def. YK2
0-35 (See Table)
User configurable relay
20
17
Output Def. YDC0
0-35 (See Table)
User configurable DC Output
3
18
Output Def. YDC1
0-35 (See Table)
User configurable DC Output
29
19
Output Def. YDC2
0-35 (See Table)
User configurable DC Output
29
20
Output Def. YDC3
0-35 (See Table)
User configurable DC Output
20
21
Output Def. YDC4
0-35 (See Table)
User configurable DC Output
20
22
Output Def. YDC5
0-35 (See Table)
User configurable DC Output
2
23
Output Def. YDC6
0-35 (See Table)
User configurable DC Output
20
24
Output Def. YDC7
0-35 (See Table)
User configurable DC Output
20
25
Input Define X0
0-21 (See Table)
User configurable Input
8
26
Input Define X1
0-21 (See Table)
User configurable Input
7
27
Input Define X2
0-21 (See Table)
User configurable Input
2
28
Input Define X3
0-21 (See Table)
User configurable Input
2
29
Input Define X4
0-21 (See Table)
User configurable Input
4
30
Input Define X5
0-21 (See Table)
User configurable Input
3
31
Input Define X6
0-21 (See Table)
User configurable Input
2
32
Input Define X7
0-21 (See Table)
User configurable Input
2
33
Open Alrm Time
0-255
Open Alarm Time in minutes. Requires at least one output to be
configured to function 25. Menu will be hidden if no outputs are
configured to function 25.
0
34
X10 PE Cut-Out
0 - 30
X10 Photoeye cut-out height (Passcode required)
24
35
X11 PE Cut-Out
0 - 66
X11 Photoeye cut-out height (Passcode required)
60
36
I-Zone Cut-Out
0 - 48
I-Zone cut-out height
42
37
Set Close Timer**
Preann. to Close**
0 - 255/Toggle Mode
Close Timer in seconds. Set to Toggle Mode to disable automatic
closing.
6
38
Preann. to Close
0 - 255
Preannounce to close timer in seconds
2
39
Preann. to Open
0 - 255
Preannounce to open timer in seconds
Disabled
40
Autocycle Time
0 - 254/Disabled
Autocycle Time in minutes
Disabled
*# (number) is not shown in i-COMM ii Menu
** The shortest reclose time available is 2 seconds. Set Preann. to Close at 1 and Set Close Timer to 1. If less than 2 seconds is needed,
consult Aftermarket for special program.
160401
30Publication: AMEN00047 2017-03-06
Rite-Hite®
Installation/Owner's Manual SplitSecond™
Side Rolling Door
INSTALLATION
GENERAL FOLDER
INVERTER FOLDER
LOAD / SAVE FOLDER
VIEW FOLDER
Folders Continued
i-COMM ii / Encoder Set-Up Continued
#*
NAME
41
Clock
42
Language
43
PassCode
44
Reversing Edge
Option
45
46
VALID VALUES
DESCRIPTION
VALUE
Displays Current Time and Date. To Set: Press UP; Scroll to
correct year; Press Enter; Scroll to correct Month; Press Enter;
Scroll to correct Day; Press Enter; Scroll to correct Hour; Press
Enter; Scroll to correct Minute; Press Enter
-
Set LCD Display Language
English
Use to change access mode.
-
Enabled/Disabled
Used to enable reversing edge
Disabled
Spec. Package
Disabled, CE Option, Canada Option
Used to enable specification packages
Disabled
Compact User Int
Enabled/Disabled
Used to enable remote LCD
Disabled
47
Partial Open
Disabled, Standard, Custom 1
Used to enable partial open operation.
-
48
Reverse Delay
xx
Reversing Delay
0
49
AB Inverter Delay
-
Consult Engineering, Special Applications Only
-
50
Voltage
208/220/230/400/460/575
Voltage of door
460
51
Square Feet
0-999
Square footage of door. Width x Height
0
52
Non-Powered Open
Enabled/Disabled
Enables non-powered open for LiteSpeed
53
Maint. Months
xx
Number of Months before Maintenance Indicator goes off.
If maintenance criteria has been met and light is flashing
initiate “Reset Maintenance” Procedure.
6
54
Maint. Cycles
0-100000
Number of Cycles before Maintenance Indicator goes off.
If maintenance criteria has been met and light is flashing
initiate “Reset Maintenance” Procedure.
100000
55
Reset Maint.
-
Resets Maintenance Counters and Timers. Press Up to initiate the
reset.
-
56
Speed Threshold
0-100%
Used to adjust the speed threshold for the counterweight sensor.
-
57
Reset to Default
-
Resets all settings back to factory defaults
-
58
Disp. Cycle Count
0 - 99999999
Displays current Cycle Count
-
59
Fault History
-
Displays fault log. Use UP and Down to Scroll
-
60
Display Model #
-
Displays door model
-
61
Display RHC#
-
Displays RHC number
-
62
Display Serial#
-
Display door serial number
-
English,Español, Portuguese
63
Firmware Reversing
-
Displays current program revisions
-
64
Copy from SD
Press UP to Start Copy
Use to upgrade i-COMM ii program. Correct .BIN file must be
saved to SD Card. Note: SD Card must be 2GB micro SD.
-
65
Copy to SD card
Press UP to Start Copy
Use to copy i-COMM ii program to SD Card in .BIN format.
-
66
Legal info to SD
Press UP to Start Copy
Use to display legal information about program. Legal.txt will be
saved to SD card.
-
67
Bootloader Upd.
Press UP to Start Copy
Used to upgrade bootloader.
CAUTION: DO NOT INTERRUPT THIS PROCESS.
-
68
Export Settings
Press UP to Start Copy
Use to save i-COMM ii settings to SD Card in .BIN format.
-
69
Import Settings
Press UP to Start Copy
Use to copy i-COMM ii settings to SD Card in .BIN format.
-
70
Inverter Type
CT SK MODBUS, AB PF40
MODBUS, CT SK NO MODBUS,
AP PF NO MODBUS, No inverter
Used to set inverter type
CT SK MODBUS
71
Program Inverter
Press UP to Start Copy
Use to program inverter. (Passcode required)
-
72
Open Speed
0 - 90 Hz
Open Speed
80.0
73
Close Speed
0 - 90 Hz
Close Speed
24
74
Approach Speed
0 - 90 Hz
Approach Open Speed
40.0
75
Accel Time
0 - 10.0 s
Acceleration Rate
1.0
76
Accel Time 2
0 - 10.0 s
Acceleration Rate 2
-
77
Decel Time
0 - 10.0 s
Deceleration Rate
0.5
78
Torque Reversing
Level
0-100%
Torqure Reversing Level
50.0%
79
DC Brake Time
0 - 10.0 s
Injection Braking Time
0.8
80
DC Brake Level
0-100%
DC Injection Braking Level
120.0%
*# (number) is not shown in i-COMM ii Menu
Publication: AMEN00047 2017-03-06
160401
31
SplitSecond™ Side Rolling Door Installation/Owner's ManualRite-Hite®
INSTALLATION
i-COMM ii / Encoder Set-Up Continued
Input / Output Values
Output
Input
TYPE
#
FUNCTION
DESCRIPTION
0
Interlock In
Interlock Input - When Input is set to this function door will not open until input is ON. Valid only for inputs X3, X4, and X5.
1
Stop N.C.
Stops the door when input is OFF.
2
Activation
Opens the door when input is ON, w/ Auto close.
3
Toggle
Open and Closes the door when ON. Door will not automatically close when opened by a toggle input.
4
Close
Closes the door when input is ON.
5
Sequential Activation
Activates door and blocks sequential activation output from triggering opposite door. Use only for sequential interlocks.
6
Reverse
Reverses the door when input is ON.
7
Stop N.O.
Stops the door when input is ON.
8
Manual Open
Opens the door when input is ON. This input will open from a stop condition, unlike activation. Do not connect motion
sensors or other automatic devices to a manual open input.
9
Auto / Manual
When input is ON reclose timer is disabled.
10
Partial Open Activation
Opens the door to the partial open position when ON
11
Partial Open Toggle
Toggle open/close door to and from partial open position. See function #3 above.
12
Toggle w/ Auto Close
Open and Closes the door when ON. Door will automatically close when opened by this type of toggle input.
13
Hand / Auto Mode
When input is ON reclose timer is disabled and hold-to-run close is enabled.
14
Disabled
Input disabled.
15
Reverse N.C.
Reverses the door when input is OFF.
16
Clean
Opens door to "Cleaning" position when on.
17
E-Stop
Places door in fault when OFF.
18
Seq. Activation 2
Consult Engineering
19
LZR in N.C.
Reverses the door when off and monitors the input for fault
20
Pre-announce to Open
Opens the door after the set amount of time in the Preann. to Open timer. Immediate reversal/activation if the door
is not closed.
21
Interlock Override
Opens the door and overrides any standard interlock configuration
0
Interlock
ON when door is closed.
1
Interlock N.C.
OFF when door is closed.
2
Pre-announce
ON during pre-announce to close, and stays on until the door is closed.
ON when door is open.
3
Open
4
Open N.C.
OFF when door is open.
5
Fault
ON during fault.
6
Ready
ON when not in fault.
7
Activation
ON during activation.
8
Run Open
ON during run open.
9
Run Close
ON during run close.
10
Run
ON during run open or close.
11
At Limits
ON when door is open or closed.
12
I-Zone Alarm
ON during I-Zone alarm.
13
Door Open 30 sec.
ON when door is open for more than 30 seconds.
14
Door Open 60 sec.
ON when door is open for more than 60 seconds.
15
Door Open 120 sec.
ON when door is open for more than 120 seconds.
16
Sequential Activation
ON to activate opposite door. Use for sequential interlock.
17
Run Open N.C.
OFF during run open.
18
Run Close N.C.
OFF during run close.
19
Run Close N.C.
OFF during run open or close.
20
Disabled
Always OFF.
21
Flash 3.1 Hz
Flashes at 3.125 Hz.
22
Flash 1.6 Hz
Flashes at 1.5625 Hz.
23
Partial Timer
Consult Engineering
32Publication: AMEN00047 2017-03-06
Rite-Hite®
Installation/Owner's Manual SplitSecond™
Side Rolling Door
INSTALLATION
i-COMM ii / Encoder Set-Up Continued
Input / Output Values Continued
Output
TYPE
#
FUNCTION
DESCRIPTION
24
Reverse / Activation
ON when any reverse command or activation signal is on.
25
Door Open Alarm
ON when door has been opened for time set in "Open Alrm Time"
26
Interlock Pass-Thru
ON when door is able to be opened (Interlock Input is not preventing door from opening)
27
Interlock Pass-Thru N.C.
OFF when door is able to be opened (Interlock Input is not preventing door from opening)
28
Preannounce & Close
ON during preannounce to close, and while closing. Note: this output will turn on while door is closed from Toggle or Close
command or re-close timer.
29
Photoeye Test
ON when emitters are on, OFF to test photoeyes
30
Encoder Bit 9
Consult Engineering
31
Encoder Bit 10
Consult Engineering
32
Encoder Bit 11
Consult Engineering
33
Encoder Bit 12
Consult Engineering
34
Preannounce to Open
ON during the set preannounce to open time.
35
Preannounce to Close
ON only during preannounce to close. OFF during run close
36
Preannounce & Flash
Flashes at 3.1 Hz during preannounce to close. OFF during run close.
Rev112414
Inverter (VFD) Programming
230/460V – Emerson
These instructions are only to change parameters when not using the i-COMM ii.
When in Status mode, pressing and holding the "M" MODE
key for 2 seconds will change the display from displaying a
speed indication to displaying load indication and visa versa.
Pressing and releasing the "M" MODE key will change
the display from status mode to parameter view mode. In
parameter view mode, the left hand display flashes the
parameter number and the right hand display shows the value
of that parameter.
Pressing and releasing the "M" MODE key again will change
the display from parameter view mode to parameter edit mode.
In parameter edit mode, the right hand display flashes the
WARNING:
value in the parameter being shown in the left hand display.
Pressing the "M" MODE key in parameter edit mode will return
the drive to the parameter view mode. If the "M" MODE key
is pressed again then the drive will return to status mode, but
if either of the "UP" or "DOWN" keys are pressed to change
the parameter being viewed before the "M" MODE key is
pressed, pressing the "M" MODE key will change the display
to the parameter edit mode again. This allows the user to very
easily change between parameter view and edit modes whilst
commissioning the drive.
Consult factory before changing any parameters not listed in this table.
AVERTISSEMENT: Contactez l'usine avant de modifier les paramètres non répertoriés dans ce tableau.
Parameter Number
Name
Default Value
Value
Units
00.03
Acceleration Rate 1
5.0
0.5
s/100 Hz
00.04
Deceleration Rate 1
10.0
0.5
s/100 Hz
A
00.06
Motor Rated Current
2.93
2.93
00.10
Security Status
L1
L2
00.19
Close Speed
17.00
25.00
Hz
00.20
Open Speed
70.00
60.00
Hz
00.21
Approach Open Speed
40.00
25.00
Hz
00.61
Torque Detection Level
0
60
%
00.66
Injection Braking Level
50
70
%
00.67
Injection Braking Time
.4
.7
seconds
Publication: AMEN00047 2017-03-06
33
SplitSecond™ Side Rolling Door Installation/Owner's ManualRite-Hite®
INSTALLATION
Inverter (VFD) Programming Continued
230/460V – Error Codes
#
TRIP CODE
CONDITION
POSSIBLE CAUSE
1
tr UU
DC bus under voltage
Low AC supply voltage, check power source.
Low DC voltage when supplied by an external DC power supply
2
tr OU
DC bus over voltage
The DC bus (Pr. 84) has exceeded 800V-460V or 400V-230VAC. Check the following:
-If DC bus climbs while door is not running, disconnect CE filter with power off.
-If fault is intermittent when door is not running try to set Automatic reset of faults.
(PR. 73 = 10.34, PR. 74=10.36, PR. 63 = 3, PR 64 = on)
-If fault is while door is closing add braking resistor, see Control Box Explosion for a list of parts.
Deceleration rate set too fast for the inertia of the machine. Mechanical load driving the motor
19
tr It.br
I2C on braking resistor
Check door closing speed. If fault is while door is closing, add breaking resistor.
See Emerson Advanced User Guide for "tr OV" troubleshooting.
20
tr It. AC
I2C on drive output
Check that radial spacing and that they are square, or lower track spacing.
Motor wiring: check for loose connections or shorts.
Make sure door cannot move if brake is engaged.
3
tr OI.AC
Drive output instantaneous over
current
Door is mechanical binding or jammed.
Check radial spacing and that they are square, or lower track spacing.
Motor wiring, check for loose connections or shorts.
Make sure door cannot move if brake is engaged. Disconnect CE filter with power off.
Insufficient ramp times. Phase to phase or phase to ground short circuit on the drives output. Drive requires
auto-tuning to the motor.
Motor or motor connections changed, re-auto tune drive to motor
MUST wait 10 seconds to reset after trip occurs
4
Ol.br
Braking resistor instantaneous
over current
Excessive braking current in braking resistor
Braking resistor value too small. MUST wait 10 seconds to reset after trip occurs
7
O.SPd
Over speed
Excessive motor speed (typically caused by mechanical load driving the motor)
18
tunE
Auto tune stopped before
complete
Run command removed before auto-tune complete
19
lt.br
I2-t on braking resistor
Excessive braking resistor energy
20
lt.AC
I2-t on drive output current
Excessive mechanical load. Drive requires re-auto tuning to motor.
High impedance phase to phase or phase to ground short circuit at drive output.
21
O.ht1
IGBT over heat based on
Overheat software thermal model drives thermal model
22
O.ht2
Over heat based on drives heatsink
Heat-sink temperature exceeds allowable maximum
24
th
Motor thermistor trip
Excessive motor temperature
26
O.Ld1
User +24V or digital output
overload
Excessive load or short circuit on +24V output
The Enable/Reset terminal will not reset an O.Ld1 trip. Use the Stop/Reset key.
OUL.d
I x t overload
Reduce motor current
hot
Heat-sink/IGBT temp is high
Reduce ambient temperature or reduce motor current
br.rS
Braking resistor overload
See Advanced user guide
31
EEF
Internal drive EEPROM failure
Possible loss of parameter values
32
PH
Input phase imbalance or input
phase loss
One of the input phases has become disconnected from the drive.
33
rS
Failure to measure motors
Motor too small for drive stator resistance.
Motor cable disconnected during measurement.
189
O.cL
Overload on current loop input
Input current exceeds 25mA
tr HF ##
Hardware Fault
The drive has detected a hardware problem; verify wiring is correct.
This cannot be fixed in the field. Replace the drive.
HF 05 trip
No signal from DSP at start up
HF 06 trip
Unexpected Interrupt
HF 07 trip
Watchdog failure
HF 08 trip
Interrupt crash (code overrun)
HF 11 trip
Access to the EEPROM failed
HF 20 trip
Power stage—code error
HF 21 trip
Power stage—unrecognized frame size
HF 22 trip
OI failure at power up
HF 25 trip
DSP Communications failure
HF 26 trip
Soft start relay failed to close, or soft start motor failed, or braking IGBT short circuit at power up
HF 27 trip
Power stage thermistor fault
HF28 trip
DSp software overrun
HF xx trip
HF 1-4, 9-10,12-19,23,24,29,30 Are not used
160401
34Publication: AMEN00047 2017-03-06
Rite-Hite®
Installation/Owner's Manual SplitSecond™
Side Rolling Door
INSTALLATION
Inverter (VFD) Programming Continued
230/460V – Status Modes
LEFT DISPLAY
STATUS
EXPLANATION
rd
Drive ready
The drive is enabled and ready for a start command. The output bridge is inactive.
ih
Drive inhibited
The drive is inhibited because there is no enable command, or a coast to stop is in progress or the drive is inhibited
during a trip reset.
Er
Drive has tripped
The drive has tripped. The trip code will display in the right hand display.
dC
Injection braking
DC injection braking current is being applied to the motor.
Fr
Drive output frequency in Hz
SP
Motor speed in RPM
Ld
Load current as a % of motor rated load current
A
Drive output current per phase in A
575V Allen Bradley
! WARNING / AVERTISSEMENT
Consult factory before changing any parameters not
listed in this table.
Contactez l'usine avant de modifier les paramètres
non répertoriés dans ce tableau.
Parameter
Number
Name
Default
Value
New
Value
039
Accel Time
0.5
a/r
040
Decel Time
0.3
a/r
056
Torque Detection Level
70.0
a/r
072
Open Speed
70.0
a/r
073
Approach Open Speed
40.0
a/r
075
Close Speed
17.0
a/r
080
DC Brake Injection Time
0.5
a/r
081
DC Brake Injection Level
1.50
a/r
101
Program Lock
1
0
Press "ESC" once to display the Display Group
parameter.
Press "ESC" again to enter the group menu, the group
letter will flash. Press "UP" or "DOWN" arrow to scroll
through the group menu.
Press "Enter" or "Sel" to enter a group. Press "UP" or
"DOWN" arrow to scroll through the group menu.
Press "Enter" or "Sel" to view the value of the parameter.
Press "ESC" to exit without making any changes. Press
"Enter" or "Sel" to edit parameter, when # is flashing
(Program LED will illuminate if parameter can be edited),
press "UP" or "DOWN" arrow to change value.
Press "Enter" when completed to save changes.
Press "ESC" to exit and return to program list
Publication: AMEN00047 2017-03-06
Figure 43
35
SplitSecond™ Side Rolling Door Installation/Owner's ManualRite-Hite®
OPERATION
Verify Operation of Controls Monthly
1. The door operations are controlled by a Universal
Controller (i-COMM ii). The controller is set-up and
programmed during testing at the factory. Only
Rite‑Hite authorized service technicians should
change the programming.
Photoeye
D
B
C
They MUST be at:
18in [457mm]
36in [914mm]
54in [1.3m]
2. To quickly determine if the door is ready to operate:
a. Open the control box
b. Look at the row of (X) green Input LED's on the
i-COMM ii and the label to verify proper state
("Logic Chart" on page 23.)
3. All wires connected for the photoeyes?
DO NOT change the
location of photoeyes.
A
4. Are loose wires secured away from moving parts?
5. With the power on, press the "OPEN" button, the door
should open and close automatically after a short
delay. To adjust the amount of door open time, the
setting must be changed in the i-COMM ii controller.
6. Operate and observe the door opening to make sure
that it fully opens. Observe the closing action to make
sure that the door operates smoothly, and fully closes
without excessive curtain ripple.
7. If it is necessary to adjust either position, refer to
Encoder adjustment section.
8. While the door is closing, block the reversing
photoeyes. The door should reverse direction,
move to the open position, and continue to operate.
9. Using end user material handling equipment,
approach door slowly and verify that all the activation
devices that are being used are operating properly.
DO NOT attempt to drive through a door in which the
green button is flashing.
Figure 44
Locate the receiver photoeye (A) on the drive side sideframe.
Located on the top of the photoeye are 3 LEDs.
• The yellow LED (B) will be ON when the output is
energized.
• The orange LED (C) will be on when the margin is > 2.5.
• If the yellow and green LED's are OFF, either the beam
is blocked or the photoeye is out of alignment.
• The green LED (D) should be ON when the photoeye
is powered and blocked causing the yellow and orange
light to go OFF.
The source photoeye on the non-drive sideframe will only
have the green LED for power.
10. Use caution (honk horn) and look in all directions
when approaching a door that is closing and ensure
that the door will reverse before proceeding.
11. Advise pedestrians to use man doors if present and
not to lean into the door way.
12. While the door is closing, impact the leading edge
(3) times to make sure that the door reverses and
goes open and faults out. Press the green flashing
"OPEN/RESET" button to return to normal operation.
13. Cover(s) installed.
14. Remove stainless steel sheet metal protective
covering.
15. After installation, it may be required to caulk the
perimeter of the door sideframes and header,
consult end user.
36Publication: AMEN00047 2017-03-06
Rite-Hite®
Installation/Owner's Manual SplitSecond™
Side Rolling Door
OPERATION
Brake Release
Door Mounted Side Brake Release
1. To manually release the brake on a SplitSecond Steel
Sideframe door on the mounted side, slowly pull up
on the handle (A). DO NOT keep pulling up on handle
or curtain will slam open.
A
2. To manually release the brake on a SplitSecond
Fabric Sideframe door on the mounted side, open the
sideframe and pull on the brake cable. DO NOT keep
pulling on the cable or curtain will slam open.
Figure 45
Final Checklist
Description

N/A
Control box conduit mounting location (must be on the bottom)
Ground wires properly terminated to ground terminal
Shield wires properly terminated to ground terminal
Motor ground wire terminated to Sideframe ground screw
Encoder - set screws properly & tighten
Encoder cable tightened properly
Sideframes properly spaced
Sideframes caulked
Sideframes square to wall
Sideframes shimmed properly if jamb cap present
Photoeye wires properly secured to Sideframe
Proper mounting fasteners used
Drive shroud installed
Verify lintel seal is sealing
Open and closed position adjusted appropriately
Area clean of debris from installation
Notes:
Rev. SPLT121115
Publication: AMEN00047 2017-03-06
37
SplitSecond™ Side Rolling Door Installation/Owner's ManualRite-Hite®
MAINTENANCE
Rite-Hite Planned Maintenance
Customer:
Job #
Planned Maintenance
Task
Recommended P.M. in months
1
6
12 18 24 30
Activation
Belting/Sprockets
Serial #
x
x
Bottom Seal
x
x
x
x
Date:
x
36
Inspect and Perform the Following:
x
Operate all devices to verify proper operation.
Verify belt is tensioned properly. Check belt and sprockets for wear.
See page 18 for details.
x
x
x
x
x
x
Verify bottom seal is sealing and properly attached.
Brake/Non-Powered Opening
x
x
x
Verify that brake stops the door at open and closed positions as well as when
stopped in the middle of travel. To move the curtain manually, release the
break by pulling the rope. The curtain should roll open automatically. If brake
is making noise, adjust.
Chain/Sprockets
x
x
x
Verify chain is tensioned properly. Check chain and sprockets for wear and
lubricate as required.
Controls / Wiring
x
x
x
Clean and check all connections with disconnect off. Make sure all wires are
free from moving parts.
Curtain
x
x
x
Inspect for wear or damage; patch immediately. Clean with warm soapy water.
Door Assembly
x
x
x
Perform visual inspection for damage. Tighten all hardware. Replace any
worn labels. Use air hose to remove dust and debris.
Door Operation
x
x
x
Operate door and make sure all operations are functioning properly.
x
x
x
Verify encoder set screws are tight. Verify lock collar on encoder is tight.
Check open and close positions; adjust as required.
Gearbox
x
x
x
Check gearbox fluid level; fill with Mobil - SHC 624 or Phillips 66 - Syncon 32
if low. Check lock collar set screws.
Header Seal
x
x
x
Verify header seal is sealing curtain to header
Leading Edge
x
x
x
Verify leading edges are sealing properly, adjust tension arm as required.
Motor
x
x
x
Check junction box and plug connections.
x
Verify all three photoeyes are aligned and reverse the curtain. LEDs on
receiver should go ON/OFF. Clean emitter and receiver lens.
x
Encoder
Photoeyes
x
x
x
x
x
x
Pillow Block Bearings
x
x
x
Lubricate as required
Shrouds and Covers
x
x
x
Make sure all shrouds and protective covers are in place and securely
fastened.
x
Perform visual inspection. Verify proper sideframe width and tighten all
hardware. If sideframe latch is present, verify it works properly. Make sure
sideframe covers open and close properly. Verify all seals are sealing
properly.
Sideframe/Covers/Seals
x
x
x
x
Tension Arm
Torque Setting
x
x
x
x
x
x
x
x
x
Verify tension arms are adjusted properly and sheer pin is in place.
x
Test the leading edge torque and adjust
Trolleys
x
x
x
Verify Trolley Rollers are functioning properly.
Vision
x
x
x
Inspect vision for tears or separation. Clean with warm soapy water.
38Publication: AMEN00047 2017-03-06
Rite-Hite®
Installation/Owner's Manual SplitSecond™
Side Rolling Door
MAINTENANCE
Troubleshooting
DEFINITION
FUNCTION
Activation
It is preferred not to wire activation devices until after the door is functioning properly.
Brake/Bridge
Rectifier
If the brake is not functioning properly, check:
a. F7 fuse (replace)
b. Rectifier, must have 120VAC incoming and 105VDC outgoing
c. Brake wiring at terminals BRK & N and junction box connections
d. Brake will have 335 ohms on normal readings (must be checked after the rectifier)
Control Box Cable
DO NOT DRILL HOLES ON TOP OF THE CONTROL BOX TO RUN CONDUIT, AS DUST PARTICLES AND MOISTURE MAY CAUSE
DAMAGE TO ELECTRICAL COMPONENTS. THE SAFEST LOCATION IS AT THE BOTTOM.
Failure to do so, voids warranty. Supplied conduit cable is pre-wired. If it is too short, DO NOT splice wires, as the cable is shielded to prevent
electrical noise. Make sure the motor is grounded and the braided (drain) wire is properly grounded to prevent electrical noise. Contact local
Representative for replacement.
Curtain
If both or only one side of the curtain does not roll onto the tube, or it rolls crooked, check:
a. Curtain dragging and catching on the floor, sideframe or seals.
b. Spring is broken, replace as required. If the curtain does not fully open or close, adjust the open or closed positions as needed.
c. Adjust the noses to maintain a tight seal by adjusting the leading edge arm bolt.
d. Adjust the lower base plate to align noses.
e. Make sure top of curtain is not loose, if it is, verify that additional piece of curtain is installed at the top.
Disconnect Switch
The disconnect switch is in line with fuse holder terminals F1, F2, F3, and removes power from the entire control box, except for incoming wires
to bottom of disconnect.
Drive Belt
(Pharma Door)
a. The drive belt tension is pre-determined at the factory. Check:
b. If the drive belt is walking across the pulleys, loosen the belting from the pressure plates and re-position belting on the pressure plate.
c. If door is slamming open or closed, this causes premature wear on the belting. Adjust the open and close positions so the door will not slam
open or close.
d. If the door open and close position keeps changing, check belt tension, as it may be loose.
Drive Chain
(Non-Pharma Door)
The drive chain tension is pre-determined at the factory. Check:
a. If the drive chain has excessive sag, tighten so there is a maximum of 1/4" sag in the middle.
b. If door is slamming open or closed, this causes premature wear on the chain. Adjust the open and close positions so the door will not slam
open or close.
Drive Side Switch
In order to switch from a right to left hand drive or vise versa, a new door would need to be ordered.
Encoder
See Encoder Section. THE ENCODER CABLE SHOULD NEVER BE SPLICED OR EXTENDED.
a. If curtain is not stopping at the same position, make sure encoder cable is grounded.
b. Verify encoder chain is operating properly and sprocket set screws are tight to shafts.
c. See page 26 for i-COMM ii Encoder errors.
Fuses
F1, F2, F3: Incoming power fuses, must have line voltage across all 3 legs. (Transformer, Inverter, motor)
F4, F5: Primary side transformer fuses, must have line voltage across both legs.
F6, F7: S
econdary side transformer fuses, F6 is 24VAC (FR only - heated pull cord) and F7 is 120V (power supply & brake).
i-COMM™ ii
Controller
The i-COMM ii controller is a circuit board that controls the actions of the door. There is a digital display that shows the cycles, status and position
of the door at any time during its travel. For input and output function signals, refer to chart on page 32-33. Settings can be changed for
re-close or pre-announce timers, interlocks, special activation commands, among others. Refer to instructional manual included.
a. Verify i-COMM ii is receiving 24VDC from power supply.
b. If i-COMM ii display is blank or hard to see, adjust contrast.
c. Input X10 - Lower photoeye will be on unless photoeye is blocked, not aligned or mis-wired.
d. Input X11 - Upper photoeye will be on unless photoeye is blocked, not aligned or mis-wired.
e. Input X14 - Fault needs to be on for the door to operate (chain hoist).
f. The door can be set to close from 2 to 255 seconds. Follow i-COMM ii adjustment instructions.
Inverter
See page 33-35 for proper parameter settings.
K8 Relay
K8 Relay is for energizing the brake, check the following:
a. Terminals 1 & 5 on the relay are wired to B3 & T1 on Inverter.
b. Terminal 7 is wired to F7 fuse and terminal 4 is wired to BRK (120VAC).
Leading Edge
The leading edge when impacted will reverse the door to the open position, time out then close. If the edge is impacted 3 consecutive times
without reaching the close position, the door will reverse, stay open and the green open/reset button will flash until the button is reset. Adjust
Torque if required, consult factory.
Membrane Switch
For steel sideframe covers only, utilizes a Open, Stop and Close buttons.
a. With Open button pushed, check between Brown and White wires.
b. With Stop button pushed, check between Brown and Red wires.
c. With Close button pushed, check between Brown and Green wires.
Motor
If door will not run when given an activation, check the following:
a. Check voltage to inverter.
b. Check voltage and for loose wires at terminals, U, V, and W.
c. 208V-240V motor will have 6 ohms on normal readings.
d. 400V-480V motor will have 20-23 ohms on normal readings.
e. 575V motor will have 34 ohms on normal readings.
Motor Phasing
If "Open/Reset" button is pressed and the door closes, phasing is reversed; switch wires in terminals, V and W.
Make sure the motor is properly grounded to prevent electrical noise.
Publication: AMEN00047 2017-03-06
39
SplitSecond™ Side Rolling Door Installation/Owner's ManualRite-Hite®
MAINTENANCE
Troubleshooting Continued
Definition
Function
Non-Powered
Opening (NPO)
The door can be opened manually in cases of electrical power outage. Pull and hold the manual brake release cord hanging from the drive motor,
no more than 1'-2' at a time or serious damage may occur. This cord releases the brake and allows the torsion springs to open the door. Release
the brake cord to stop the door movement before it fully opens to prevent the trolleys from hitting the header assembly.
Open/Reset Push
Button
The following are functions of the open/reset push button. The first function is when pressed, is to open the door. The second function is to reset
the door when in a fault mode. When pressed the door will open (after 5 seconds door will automatically run) and automatically close and after
the preset time has expired, unless the door is in a true toggle operation. When the door reversing edge has been impacted three times the light
will flash and the door will not operate from an activation command. The light will continue to flash until the open/reset button is pushed.
The green light will flash due to:
a. Power outage or startup
b. Reversing edge impacted three times.
Photoeyes
Power Supply will have green light on if powered.
a. Powered by 120VAC from F7 fuse.
b. Supplies i-Comm ii 24VDC.
c. If i-Comm ii is not powered and amber light is on, unplug 8 pin (J4 connector) and power up, if green light is on, check each DC wire for short.
Power Supply
Power Supply will have green light on if powered.
a. Powered by 120VAC from F7 fuse.
b. Supplies i-Comm 24VDC.
c. If i-Comm is not powered and amber light is on, unplug 8 pin (J4 connector) and power up, if green light is on, check each DC wire for short.
Pressure
Tension arm holds the curtain in position to maintain a tight seal at the nose. If the sheer pin breaks due to negative pressure, wind or an impact,
you will need to replace the sheer pin.
Re-close Timer
The door can be set to close from 2 to 255 seconds, follow i-COMM adjustment instructions.
Transformer
The standard transformer is a tri-volt transformer that takes an incoming voltage of 208V, 230V, 460V and converts it to 110VAC and 24VAC.
An optional transformer is available for 380V, 415V and 575V doors.
a. 208V
b. 230V
c. 380V
d. 460V
(Taps
(Taps
(Taps
(Taps
H1-H2)
H1-H3)
H1-H2)
H1-H4)
13
15
40
28
Ohms
Ohms
Ohms
Ohms
e. 415V (Taps H1-H3) 43 Ohms
f. 575V (Taps H1-H4) 58 Ohms
g. 120V (Taps X1-X3) 4.4-4.8 Ohms
h. 24V (Taps X1-X2) .4 to .6 Ohms (230-460V)
Voltage Change
To change the voltage:
a. Change transformer taps and fuses per electrical diagram.
b. Change motor wiring per junction box diagram.
c. Replace Inverter with proper voltage.
d. Brake resistor
e. Change voltage selection on i-COMM ii
X0
Input programmed for a device to open the door.
X1
Input programmed for a device to stop the door.
X2, X3, X6, X7
Activation Inputs - If on and door is not closing, verify activation device is not faulty.
X4
Input programmed for a device to close the door.
X5
Input programmed for a device to toggle open / close the door.
X9
36in [914mm] Photoeye Input - MUST be on; if off, verify aligned and powered
X10
18in [457mm] Photoeye Input - MUST be on; If off, verify aligned and powered.
X11
54in [1372mm] Photoeye Input - MUST be on; if off, verify aligned and powered
X12
Open / Reset Button - X12 will illuminate when button is pressed
X13
Induction loop Input - if on door will stay open - verify object is not present on the floor loop
X14
Fault Input - Verify chain hoist chain has not been pulled.
X15
Power Input - Indicates unit is powered
YK0
Interlock output
YK1
Programmable output
YK2
Programmable output
YDC0
Output programmed to be on when door open.
YDC5
Output programmed for Pre-announce to close.
i. 120V (Taps X1-X3) 5.2 Ohms (380/415V)
j. 24V (Taps X1-X2) 5.7 Ohms (380/415V)
k. 120V (Taps X2-X3) 4.5 Ohms (230-460V)
l. 24V (Taps X2-X3) 5.0 Ohms (380/415V)
40Publication: AMEN00047 2017-03-06
Rite-Hite®
Installation/Owner's Manual SplitSecond™
Side Rolling Door
ELECTRICAL
Wireless Activation
A
C
B
D
Figure 46
Pair the unit(s) at the control box prior to mounting.
Figure 47
To pair the host with a wireless device:
Resetting Communication Parameters
1. Apply power to the control box and wireless host unit.
If the batteries are not lasting as long as they should, reset
the communication parameters.
2. Open the cover and remove the plastic strip (A) under
the batteries in the remote unit to energize the device.
3. Press the "Pair button" (B) on the desired remote unit.
An AMBER LED will begin to flash to indicate it is in
the pairing mode.
4. On the wireless host, use a 1/8in [3mm] diameter
rod made from a non-ferous* material and insert into
the "Remote Pairing" (C) hole approximately 1 1/2in
[38mm] in depth until you feel a button depress and
then release it. The "RF Com" LED (D) will begin to
flash green once per second to indicate it is in pairing
mode.
! WARNING / AVERTISSEMENT
Performing this operation will cause the Host
to clear all paired remotes. Remotes must be
re-paired in order to re-establish communication.
Une fois cette opération effectuée, l'hôte efface
toutes les télécommandes appariées. Apparier
à nouveau les télécommandes pour rétablir la
communication.
5. Once paired, the RED and GREEN LED'S will briefly
turn on and then off. If the units are unable to pair up,
the GREEN light will continue to flash for 20 seconds
and then time out.
1. With power applied to the Host, insert a thin
screwdriver into the “Remote Pairing” slot. With the tip
of the screwdriver pointing straight into the slot locate
the “Remote Pairing” button.
6. To test, activate the remote unit. The GREEN LED on
the host and the AMBER LED on the remote should
turn on and operate the door. If not, reattempt pairing
process.
2. Using the screwdriver, apply pressure to the “Remote
Pairing” button. The GREEN LED will illuminate once
the button has been pressed.
7. Mount the remote unit at it's operating position.
8. Wiring for host unit to Control Box i-COMM ii:
4 - X6 5 - DC 6 - DC 7 - OV
3. Keep pressure applied to the button for at least 5
seconds. The GREEN LED will turn OFF to signify the
correct amount of time has elapsed.
4. Once the GREEN LED has turned OFF remove
pressure from the button.
5. The GREEN LED will turn ON for 1 second to signify
that the operation was performed successfully.
6. The Host will now RESET, causing both the RED and
the GREEN LED to briefly turn ON and then turn OFF.
7. The communication parameters have now been
successfully RESET.
* If a metal object is used, caution should be taken to not contact the circuit board inside.
Publication: AMEN00047 2017-03-06
41
SplitSecond™ Side Rolling Door Installation/Owner's ManualRite-Hite®
ELECTRICAL
Motor Voltage Wiring
208/230V & 575V
460V
400V
Compact User Interface (OPTIONAL)
A
B
C
D
Figure 48
A Compact User Interface is mounted on a stainless steel
or fiberglass 2-gang wall faceplate and compatible with
standard 2-gang electrical box (provided by end user). The
controls are also available on the provided junction box.
On the face of the assembly, there is a 4-button
membrane switch:
A. Green: Open/Reset "UP"
B. Red: Stop "EXIT"
C. Yellow: Close "DOWN"
D. Gray: Left Arrow "ENTER"
Press and hold "ENTER" button for 5 seconds to enter the
menu. The" OPEN" button on the interface will reset the
door after a fault. The screen flashes when in a fault.
NOTE: Verify Compact User Interface is Enabled in the
i-COMM menu.
42Publication: AMEN00047 2017-03-06
1
Fiberglass (OPTIONAL)
FINAL ASSEMBLY
REVISION HISTORY
CONTROL BOX CONNECTIONS
1
LOCK IN J46
D
OV
DT+
DTDC
LCD INTERFACE CONNECTIONS
DRAIN
BU/WH
BN
BN/WH
BU
BU
BU/WH
BN
BN/WH
J46
GN
GN/WH
1
LOCK IN J48
B8
B9
B10
B11
GN
GN/WH
ORG
ORG/WH
ORG
50' CABLE - PN 15650305
75' CABLE - PN 15650317
ORG/WH
REV.
DATE
NOTE
ECN
BY
B
1/4/2016
ADDED #52000071 FOR LED COUNTDOWN
7070
CDH
D
9/22/2016
CHANGED QTY (2) FOR #45550004
7272
CDH
E
2/21/2017
BOLD ALL WIRES & ADD SPLITTER VIEW
7253
CDH
+24V
0V
A
TERMINALS LOCATED
ON INTERFACE MODULE
B
B8
B9
B10
B11
IMPORTANT!
J48
THE PLUGS MUST BE CONNECTED TO THE CORRECT HEADERS.
IF NOT CONNECTED PROPERLY, THE REMOTE LCD WILL NOT
FUNCTION.
HEADERS LOCATED ON LEFT
SIDE OF i-COMM II CONTROLLER
.18
(4 PLCS.)
MOUNTING HOLES
4
CONNECT TO LED COUNTDOWN
1
1
C
CONNECT TO J46
2
1
4.53
4.06
D
Rite-Hite®
2
INSTALLATION
NEXT ASSEMBLY
3
Compact User Interface (OPTIONAL) Continued
Publication: AMEN00047 2017-03-06
4
C
CONTRAST ADJUSTMENT
CONNECT TO COMPACT USER INT
NOTE: FEMALE SPLITTER USED
WITH LED COUNTDOWN
3.55 2.37
8
5
BOM TABLE
B
ITEM
QTY
DRAWING
PART NUMBER
8
1
9999M101
52000071
HARN,SPLITTER,ICOMMII
7
2
-
45550004
FTG,STRT,L/T,PG11
INSIDE COVER VIEW
6
KIT PART NUMBERS:
53700925 - 50' CABLE
53700926 - 75' CABLE
6
1
9999M037
72700271
SW,MEMBRANE,4BTN,ICOMMII
5
4
9999M299
67850216
SCR,FHMS,PHLP,#2‑56X1‑1/4,STNL
4
4
9999M300
55600023
NUT,HEX,#2‑56,NYLON
3
4
9999M301
70450180
SPACER,NYLON,#4,3/16"ODX7/16"L
2
1
9999M286
65100029
DCC,INTERFACE MODULE2,ICOMMII
1
1
9998M024
43750168
ENCL,ABS,RMT MNT CTRL,NEMA4X
FINISH
1
TO ENABLE THE COMPACT USER INTERFACE:
MAIN MENU
---------> GENERAL FOLDER
----------------> Compact User Int - Set to "Enabled"
43
3
THIS DOCUMENT IS THE PROPERTY
OF RITE‑HITE® DOORS INC. SUBJECT
MATTER HEREIN IS CONFIDENTIAL.
DO NOT USE, REPRODUCE, COPY OR
DISCLOSE EXCEPT WITH WRITTEN
CONSENT OF RITE‑HITE® DOORS INC.
UNLESS OTHERWISE SPECIFIED DRAWN BY
DIMENSIONS ARE IN INCHES.
DRAWN DATE
TOLERANCES:
INITIAL ECN
.X
=
.050
=
.010
.XX
DATE ISSUED
=
.005
.XXX
1.0
ANGLE =
THIRD ANGLE PROJECTION
TAH
RITE-HITE ®
11/5/2014
DOORS INC.
6949 TITLE
2/21/2017 INTERFACE,CUI,NEMA4X,ICOMMII
REFERENCE
ALL SHEETS ARE THE SAME
REVISION STATUS
© 2014 RITE-HITE®
DOORS INC.
DO NOT SCALE DRAWING
2
SIZE MODEL
C
SCALE
1:1
DWG NO
PART#
9999M050
55150345
1
A
SHEET
REV
E
1 OF 1
Side Rolling Door
A
4
MATERIAL
CONFIDENTIAL
OUTSIDE VIEW
B
DESCRIPTION
Installation/Owner's Manual SplitSecond™
3
OV
DT+
DTDC
DRAIN
BU/WH
BN
BN/WH
BU
LCD INTERFACE CONNECTIONS
BU
BU/WH
BN
BN/WH
GN
GN/WH
ORG
ORG/WH
J46
1
LOCK IN J48
J48
B
NOTE
1/4/2016
ADDED #52000071 FOR LED COUNTDOWN
D
9/22/2016
Added #45550004 & CHG Remote Display text
7222
CDH
E
2/22/2017
BOLD ALL WIRES & ADD SPLITTER VIEW
7253
CDH
+24V
0V
A
B
B8
B9
B10
B11
TERMINALS LOCATED
ON INTERFACE MODULE
ECN
BY
7070 CDHTAH
B
1
CONNECT
TO J46
1
IMPORTANT!
THE PLUGS MUST BE CONNECTED TO THE CORRECT HEADERS.
IF NOT CONNECTED PROPERLY, THE REMOTE LCD WILL NOT
FUNCTION.
NOTE: FEMALE SPLITTER USED
WITH LED COUNTDOWN
1.50
1
3
TO ENABLE THE COMPACT USER INTERFACE:
MAIN MENU
---------> GENERAL FOLDER
----------------> Compact User Int - Set to "Enabled"
2
4.50
BOM Table
ITEM QTY. PART NUMBER
1
4
A
.16
4.56
NOT SHOWN
NOT SHOWN
FINISH
THIS DOCUMENT IS THE PROPERTY
OF RITE‑HITE® DOORS INC. SUBJECT
MATTER HEREIN IS CONFIDENTIAL.
DO NOT USE, REPRODUCE, COPY OR
DISCLOSE EXCEPT WITH WRITTEN
CONSENT OF OF RITE-HITE®
DOORS INC.
© 2013 RITE-HITE®
DOORS INC.
4
65000818
9999M261
DESCRIPTION
PLATE,MNT,LCD INTERFACE,STNLS
2
1
72700271
9999M037
SW,MEMBRANE,4BTN,ICOMMII
3
1
65100029
9999M286
DCC,INTERFACE MODULE2,ICOMMII
SPACER,AL,#2‑56,3/16"ODX5/16"L
4
4
70450181
9999M305
5
1
43750171
-
6
1
52000071
9999M101
7
1
44450004
-
ENCL,PLSTC,RMT MNT CNTRL
A
HARN,SPLITTER,ICOMMII
FTG,STRT,L/T,PG11
MATERIAL
CONFIDENTIAL
KIT PART NUMBERS:
53700923 - 50' CABLE
53700924 - 75' CABLE
1
DRAWING
3
UNLESS OTHERWISE SPECIFIED DRAWN BY
DIMENSIONS ARE IN INCHES.
DRAWN DATE
TOLERANCES:
INITIAL ECN
.050
=
.X
.010
=
.XX
DATE ISSUED
.005
=
.XXX
1.0
ANGLE =
THIRD ANGLE PROJECTION
CDH
RITE-HITE ®
8/27/2013
DOORS INC.
6786 TITLE
2/21/2017 INTERFACE,CUI,STNLS,ICOMMII
REFERENCE
ALL SHEETS ARE THE SAME
REVISION STATUS
DO NOT SCALE DRAWING
2
SIZE MODEL
B
SCALE
1:1
DWG NO
9999M039
PART# 55150279
SHEET
1
REV
E
1 OF 1
Installation/Owner's ManualRite-Hite®
6
CONNECT TO
COMPACT USER INT
GN
GN/WH
ORG
ORG/WH
DATE
C
HEADERS LOCATED ON LEFT
SIDE OF i-COMM II CONTROLLER
1
CONNECT TO
LED COUNTDOWN
B8
B9
B10
B11
REV.
SplitSecond™ Side Rolling Door 1
INSTALLATION
REVISION HISTORY
CONTROL BOX CONNECTIONS
LOCK IN J46
Stainless Steel (OPTIONAL)
1
2
Compact User Interface (OPTIONAL) Continued
44Publication: AMEN00047 2017-03-06
3
4
Rite-Hite®
INSTALLATION
Electrical
Publication: AMEN00047 2017-03-06
Mandatory Field Wiring Diagram – Steel Sideframes
Installation/Owner's Manual SplitSecond™
Side Rolling Door
45
SplitSecond™ Side Rolling Door INSTALLATION
Electrical Continued
Installation/Owner's ManualRite-Hite®
46Publication: AMEN00047 2017-03-06
Mandatory Field Wiring Diagram – Fabric S/F Covers
4
3
DWG NO
E
REVISION HISTORY
H1-H2
H1-H3
H1-H4
H4-H3
H4-H2
H4-H1
GN
DESCRIPTION
ECN
ADD VFD COM WIRE
7076
1/6/2016
MAS
E
CORRECTING TRANSFORMER TAP CHART
7171
6/23/2016
MDM
C
CHANGE MODBUS CABLE
6994
5/27/2015
TAH
GROUNDED TO
MOUNTING PLATE
3
5
7
2
4
6
8 10 12 14 16 18 20
D
OPTIONAL WIRELESS ACTIVATION HOST WIRING
K2N-K2 COMMON
WH/ORG
DC
ORG
K1N-K1 COMMON
0V
6
J4-1
7
8
9
6
7
8
24V
0V
CLSG
POWER
10
9
10
RE BKWY
SAFETY
SEE 7802E012
FOR PAIRING
INSTRUCTIONS
WIRELESS HOST
K0-RELAY K0 OUT
Fault
YDC2 - PHOTOEYE TEST
10A
10A
3
X1
ENCODER TERMINALS
SEE FIELD DIAGRAM
OPTIONAL PREANNOUNCE RELAY WIRING
10 AMP
575 3
6 AMP
208, 220, 230
1 AMP
0V-0V DC
DC-24V DC
X9
X11
1
J4-7
3
STB
CR3
400 - 575
-
2 AMP
-
1 AMP
X6
N
J4-10
BU
PS1
V-
N
POWER SUPPLY
V+
WHT 18 GA
BLK 18 GA
J4-12
BRAKE RELAY
1
5
CR1
J4-3
L
4
REFER TO TABLE FOR
SECONDARY SIDE
TRANSFORMER TAPS
CR1
BRK
3
F7
4
BLK 18 GA
H4 460V
AC NEUTRAL
THIS TABLE SHOWS THE FUNCTION OF EACH OF THE
CONNECTORS ON THE UNIVERSAL CONTROLLER. THE
VOLTAGES LISTED FOR EACH PIN ASSUME THAT EITHER THE
INPUT OR OUTPUT IS ACTIVATED.
CONN.
FUNCTION
VOLTAGE
1
PB POWER OUTPUT
24 VDC
2
RESET INPUT (X12)
24 VDC
3
POWER SUPPLY INPUT
24 VDC
4
LOOP INPUT (X13)
24 VDC
CHAINFALL POWER OUTPUT
24 VDC
6
FAULT INPUT (X14)
24 VDC
7
WARN. DEV. POWER OUTPUT
24 VDC
8
PB LIGHT OUT (YDC3)
0 VDC
9
IND. LOOP POWER OUTPUT
24 VDC
5
10
0 VDC
INVERTER OUTPUT (B5)
24 VDC
WARN. DEVICE OUTPUT (YDC5)
0 VDC
INVERTER COMMON (B2)
24 VDC
CHAINFALL OUTPUT (YDC6)
0 VDC
15
POWER SUPPLY INPUT
0 VDC
16
SPARE OUTPUT (YDC7)
0 VDC
17
IND. LOOP POWER OUTPUT
0 VDC
18
RS485 + COMMUNICATIONS
1 VDC
19
EARTH GROUND
0 VDC
20
RS485 - COMMUNICATIONS
-1 VDC
MOTOR
MOTOR
EARTH GROUND
EARTH GROUND
NOTES:
ALL WIRES ARE 18 AWG BLUE, UNLESS
OTHERWISE MARKED.
ALL 24VDC CONTROL WIRES ARE BLUE.
EARTH GROUND
GND
GN/YE
F1
F2
F3
BLK 14 GA
W
V
U
L1
T1
T2
L2
L3
T3
SW0 DISCONNECT
BLK 14 GA
BLK 14 GA
WIRE NOT USED ON 220V 1
L1
L2
L3
MOTOR
MOTOR
BLK 14 GA
MOTOR
W
V
U
GND
5 TWISTS/FT. MIN
GND
GND
GN/YE
INDUCTION
LOOP B
LPB
TERMINALS GROUNDED
TO BACKPANEL
INDUCTION
LOOP A
LPA
RELAY 1
RELAY 1
- INDICATES OPPOSITE END OF WIRE
0VDC IN
24VDC IN
ITEM
DESCRIPTION
PART NO.
0
0.125
0.25
1.25
5
15
40
80
0.125
0.25
1.25
5
15
40
80
-
ANGLES
FINISH
+/- 1 DEG
0.005
0.010
0.020
0.030
0.040
0.060
0.100
0.125
4
RITE-HITE
R
RITE-HITE
DO NOT SCALE DRAWING
DRAWN BY
CHECKED BY
APPROVED BY
TAH
DATE
3
A
TITLE
6/11/2012
WIRING DIAGRAM
DATE
SPLIT SECOND, i-COMM II
DATE
INITIAL ECN
6522
6/10/2012
SIZE
D
REF
DOORS INC.
R
DOORS INC.
MM-DD-YY
DATE ISSUED
5
QTY
PARTS LIST / MATERIAL
INCH TOLERANCES
OVER
UP TO
+/-
1
TO J4-17
TO J4-9
6
B
FOR SINGLE
PHASE
APPLICATIONS
SUPPLY
POWER TO L1
& L3 ON
INVERTER
PE
L1
L2
L3
BLK 14 GA
WARNING:
ALL BLACK WIRES ARE AT POTENTIALLY
LETHAL VOLTAGES.
7
DO NOT WIRE TO (-)
TERMINAL. RESISTOR IS
WIRED TO 2ND AND 3RD
TERMINAL FROM LEFT
ON BOTTOM ROW
PE
GND
GND
BLK 14 GA
C 2012
8
+
N
STB
TO J4-4
J4-x
RJ45 PORT
BRAKING RESISTOR R1
INDUCTION LOOP
CONTROLLER
13
14
MOTOR
TORQUE REVERSE
RESISTOR
11 10 9 8 7 6 5 4 3 2
A
IZONE ALARM OUTPUT (YDC4)
11
12
F5
H1
LINE VOLTAGE
LINE VOLTAGE
LINE VOLTAGE
FUSE F3 NOT PRESENT
ON 220V SINGLE PHASE
CONTROLS
DIGITAL OUT
T5
T6
INVERTER
RESISTOR
X1
WHT 18 GA
N
B3
T1
MODBUS CABLE
F4
EARTH GROUND
INCOMING POWER
FROM END USER
SUPPLIED
DISCONNECT
C
SCALE
2
MODEL NUMBER
SplitSecond
9"=1'
DWG NO
REV
E
7802E009
PART #
1755.xxxx
SHEET
1
Installation/Owner's Manual SplitSecond™
J4
PIN #
PREANNOUNCE OPTION
BIT 0
H3 230V
BLK 18 GA
CONNECTOR TABLE
COMMON
B5
REFER TO TABLE FOR
PRIMARY SIDE
TRANSFORMER TAPS
TRANSFORMER
100 VA
120V X3
H2 208V
AC NEUTRAL
B2
B7
PE
24V X2
B
INV COM
J4-15
GN/YE
5
BRAKE OUTPUT
5
J4-16
1/2 AMP
F6
5
COM
J4-11
F4/5
F7
4
4
J4-8
J4-13
PREANNOUNCE RELAY
F1/2/3
460 3
X7
3
3
X2
La
X11-PHOTOEYE TOP
15 AMP
X10
X9-IZONE (OPTIONAL)
X10-PHOTOEYE LOW
20 AMP
208, 230 3
X5
3.7A
CONTROL BOX FUSING
CURRENT RATING
VOLTAGE
220, 1
X8
X7-ACTIVATION
X8-IZONE (OPTIONAL)
5.4A
X6
X5-TOGGLE INPUT
X6-ACTIVATION
5.4A
X3
X3-ACTIVATION
X4-CLOSE PB
9.2A
X1-STOP PB
X2
17.8A
X4
BOTTOM ROW
220, 1 208-230 400, 3 460, 3 575, 3
3
SPLITSECOND
DEVICE
X1
LINE VOLTAGES
DOOR
STYLE
X2
TOP ROW
X0-OPEN PB
C
4
2
I-ZONE ALARM
(OPTIONAL)
INPUTS LAYOUT
X0
2
OPEN CLS STOP O/C
1
PB FAULT LAMP
10A
TABLE OF CONTROL BOX
FULL LOAD AMP REQUIREMENTS
ACTIVATOR
1
J4-2
YDC0 - DC OUTPUT
Remote
Pairing
RF Com
OPEN/RESET SWITCH
YDC1 - DC OUTPUT
220, 1 208-230 400, 3 460, 3 575, 3
3
15A
APPROVED
9 11 13 15 17 19
1
K2-RELAY K2 OUT
TABLE OF RECOMMENDED
FEEDER SERVICE AMPERAGES
LINE VOLTAGES
30A
BY
D
K0N-K0 COMMON
SPLITSECOND
DATE
J4
SECONDARY SIDE TRANSFORMER TAPS
OUTPUT VOLTAGE 100 KVA 150 KVA
GND
X1
X3
24V
X2
X2
120V
X1
X3
K1-RELAY K1 OUT
DOOR
STYLE
1
230/460V
REV
SHEET
7802E009
REV
PRIMARY SIDE TRANSFORMER SETTINGS
TAPS
LINE VOLTAGE
100 VA
150 VA
H1-H2
H4-H3
208
H4-H2
220-240
H1-H3
H1-H4
440-480
H4-H1
380
415
575
5
6
Rite-Hite®
-
MAINTENANCE
D
FINAL ASSEMBLY
-
Wiring Diagrams
Publication: AMEN00047 2017-03-06
7
8
NEXT ASSEMBLY
Side Rolling Door
47
4
3
DWG NO
575V
1
REV
SHEET
7802E011
F
REVISION HISTORY
REV
GN
DATE
11/17/2015
CORRECT XFMR VOLTAGES
7063
E
ADD VFD COM WIRE
7076
1/6/2016
MAS
F
CORRECTING TRANSFORMER TAP CHART
7171
6/23/2016
MDM
3
5
7
2
4
6
8 10 12 14 16 18 20
LPB
INDUCTION
LOOP A
LPA
RELAY 1
RELAY 1
TO J4-4
K2N-K2 COMMON
WH/ORG
K2-RELAY K2 OUT
K1-RELAY K1 OUT
0VDC IN
24VDC IN
D
1
TO J4-17
TO J4-9
ORG
K1N-K1 COMMON
CLS
INDUCTION LOOP
CONTROLLER
9 11 13 15 17 19
1
APPROVED
GN/YE
INDUCTION
LOOP B
J4
SECONDARY SIDE TRANSFORMER TAPS
OUTPUT VOLTAGE 100 KVA 150 KVA
GND
X1
X3
24V
X2
X2
120V
X3
X1
BY
D
5 TWISTS/FT. MIN
GROUNDED TO
MOUNTING PLATE
ECN
11 10 9 8 7 6 5 4 3 2
PRIMARY SIDE TRANSFORMER SETTINGS
TAPS
LINE VOLTAGE
100 VA
150 VA
H1-H2
H4-H3
208
H4-H2
220-240
H1-H3
H1-H4
440-480
H4-H1
H1-H2
H4-H3
380
H4-H2
415
H1-H3
575
H1-H4
H4-H1
DESCRIPTION
J4-1
K0N-K0 COMMON
DOOR
STYLE
TABLE OF RECOMMENDED
FEEDER SERVICE AMPERAGES
LINE VOLTAGES
F6
-
2 AMP
-
1 AMP
1
J4-7
3
STB
CR3
0V-0V DC
DC-24V DC
N
J4-10
BU
J4-13
PE
PS1
V-
N
POWER SUPPLY
V+
WHT 18 GA
BLK 18 GA
BRAKE RELAY
1
5
CR1
J4-3
L
4
REFER TO TABLE FOR
SECONDARY SIDE
TRANSFORMER TAPS
CR1
3
F7
4
BLK 18 GA
H4 575V
AC NEUTRAL
THIS TABLE SHOWS THE FUNCTION OF EACH OF THE
CONNECTORS ON THE UNIVERSAL CONTROLLER. THE
VOLTAGES LISTED FOR EACH PIN ASSUME THAT EITHER THE
INPUT OR OUTPUT IS ACTIVATED.
CONN.
J4
PIN #
FUNCTION
VOLTAGE
1
PB POWER OUTPUT
24 VDC
2
RESET INPUT (X12)
3
POWER SUPPLY INPUT
24 VDC
4
LOOP INPUT (X13)
24 VDC
CHAINFALL POWER OUTPUT
24 VDC
6
FAULT INPUT (X14)
24 VDC
WARN. DEV. POWER OUTPUT
24 VDC
8
PB LIGHT OUT (YDC3)
0 VDC
9
IND. LOOP POWER OUTPUT
24 VDC
10
IZONE ALARM OUTPUT (YDC4)
0 VDC
11
INVERTER OUTPUT (B5)
24 VDC
12
WARN. DEVICE OUTPUT (YDC5)
0 VDC
13
INVERTER COMMON (B2)
24 VDC
14
CHAINFALL OUTPUT (YDC6)
0 VDC
15
POWER SUPPLY INPUT
0 VDC
16
SPARE OUTPUT (YDC7)
0 VDC
17
IND. LOOP POWER OUTPUT
0 VDC
18
RS485 + COMMUNICATIONS
INVERTER
19
EARTH GROUND
0 VDC
20
RS485 - COMMUNICATIONS
-1 VDC
X1
RESISTOR
GN/YE
DO NOT WIRE TO (-)
TERMINAL. RESISTOR IS
WIRED TO 2ND AND 3RD
TERMINAL FROM LEFT
ON BOTTOM ROW
B
N
TRANSFORMER
2000 VA
STB
GND
FILED INSTALLED
14 AWG MIN, 90 DEG C
COPPER, 600V
X1 230V
EARTH GROUND
PE
GND
GND
PE
X2
MOTOR
MOTOR
EARTH GROUND
EARTH GROUND
EARTH GROUND
NOTES:
ALL WIRES ARE 18 AWG BLUE, UNLESS
OTHERWISE MARKED.
ALL 24VDC CONTROL WIRES ARE BLUE.
ALL 24VAC WIRES ARE RED.
ALL AC NEUTRAL WIRES ARE WHITE.
F1
F2
BLK 14 GA
W
V
U
BLK 14 GA
L1
T1
T2
L2
L3
T3
SW0 DISCONNECT
XH2
XX1
X4 230V
575V H2
L1
L1
L2
L3
L3
XX4
MOTOR
BLK 14 GA
MOTOR
BLK 14 GA
MOTOR
W
V
U
GND
FIELD INSTALLED BONDING JUMPER (14 GA MIN, 600V, 90 DEG C, COPPER)
GROUND AND BOND ACCORDIN TO LOCAL AND NATIONAL CODES
GND
GND
ITEM
FILED INSTALLED
14 AWG MIN, 90 DEG C
COPPER, 600V
TERMINALS GROUNDED
TO BACKPANEL
SCOPE
0
0.125
0.25
1.25
5
15
40
80
THIS DRAWING COVERS DOORS
CONFIGURED AFTER 6/18/2012
VERIFY THAT THIS DRAWING HAS NOT BEEN SUPERCEDED BY NEWER REVISION. ABOVE APPLIES
ONLY WHEN DRAWING IS CURRENT.
5
QTY
DESCRIPTION
PART NO.
PARTS LIST / MATERIAL
INCH TOLERANCES
+/OVER
UP TO
4
ANGLES
FINISH
0.125
0.25
1.25
5
15
40
80
+/- 1 DEG
0.005
0.010
0.020
0.030
0.040
0.060
0.100
0.125
N/A
RITE-HITE
R
RITE-HITE
DO NOT SCALE DRAWING
TAH
DATE
3
A
TITLE
6/11/2012
CHECKED BY
DATE
APPROVED BY
DATE
WIRING DIAGRAM - 575V
SPLIT SECOND, i-COMM II
INITIAL ECN
6522
6/10/2012
SIZE
D
REF
DOORS INC.
R
DOORS INC.
MM-DD-YY
DRAWN BY
DATE ISSUED
C 2012
6
X3
XH1
BLK 14 GA
WARNING:
ALL BLACK WIRES ARE AT POTENTIALLY
LETHAL VOLTAGES.
7
+
BRAKING RESISTOR R1
PRIOR
8
RJ45 PORT
RESISTOR
F5
H1
LINE VOLTAGE
LINE VOLTAGE
MOTOR
1 VDC
TORQUE REVERSE
MODBUS CABLE
F4
575V H1
INCOMING POWER
FROM END USER
SUPPLIED
DISCONNECT
24 VDC
7
5
PREANNOUNCE OPTION
WHT 18 GA
N
DIGITAL OUT
T5
T6
H3 415V
BLK 18 GA
CONNECTOR TABLE
C
B3
T1
REFER TO TABLE FOR
PRIMARY SIDE
TRANSFORMER TAPS
TRANSFORMER
100 VA
120V X3
H2 380V
AC NEUTRAL
BIT 0
B7
J4-12
BRK
COMMON
B5
J4-15
GN/YE
5
BRAKE OUTPUT
B2
J4-16
24V X2
B
INV COM
J4-11
X11-PHOTOEYE TOP
X9-IZONE (OPTIONAL)
X10-PHOTOEYE LOW
X7-ACTIVATION
X8-IZONE (OPTIONAL)
La
PREANNOUNCE RELAY
F4/5
F7
X5-TOGGLE INPUT
X6-ACTIVATION
1/2 AMP
X3-ACTIVATION
X4-CLOSE PB
1 AMP
400 - 575
X1-STOP PB
X2
208, 220, 230
X0-OPEN PB
6 AMP
SEE 7802E012 FOR PAIRING INSTRUCTIONS
X2
SCALE
2
MODEL NUMBER
SplitSecond
9"=1'
DWG NO
REV
F
7802E011
PART #
1755....
SHEET
1
Installation/Owner's ManualRite-Hite®
575 3
OPTIONAL PREANNOUNCE RELAY WIRING
10
10 AMP
BKWY
15 AMP
9
208, 230 3
460 3
F1/2/3
RE
X11
3.7A
20 AMP
SAFETY
5.4A
8
X9
CLSG
X10
BOTTOM ROW
CONTROL BOX FUSING
CURRENT RATING
VOLTAGE
220, 1
X7
7
5.4A
X5
0V
9.2A
X3
6 7 8 9 10
17.8A
X1
575, 3
6
SPLITSECOND
460, 3
24V
220, 1 208-230 400, 3
3
POWER
X8
5
X6
COM
X4
TOP ROW
LINE VOLTAGES
DOOR
STYLE
DEVICE
X2
DC
0V
J4-8
I-ZONE ALARM
(OPTIONAL)
INPUTS LAYOUT
X0
Remote
Pairing
ENCODER TERMINALS
SEE FIELD DIAGRAM
4
X1
3
PB FAULT LAMP
TABLE OF CONTROL BOX
FULL LOAD AMP REQUIREMENTS
X6
Fault
YDC0 - DC OUTPUT
10A
RF Com
10A
4
2
10A
J4-2
3
ACTIVATOR
15A
OPTIONAL WIRELESS ACTIVATION
OPEN/RESET SWITCH
YDC1 - DC OUTPUT
WIRELESS HOST
30A
K0-RELAY K0 OUT
YDC2 - PHOTOEYE TEST
575, 3
1 2 3 4 5
SPLITSECOND
460, 3
1
220, 1 208-230 400, 3
3
SplitSecond™ Side Rolling Door 5
MAINTENANCE
6
Wiring Diagrams Continued
-
C
A
7
FINAL ASSEMBLY
7802E001
OPEN CLS STOP O/C
48Publication: AMEN00047 2017-03-06
D
8
NEXT ASSEMBLY
DWG NO
7802E012
F
REVISION HISTORY
NEXT ASSEMBLY
REV
BEA - Falcon, Eagle,
MS08
Control Box
D
DC
0V
DC
X6***
Sensor
1-RD
2-BK
3-WH
4-GN
not used 5-YE
BEA - IRIS
Sensor
Control Box
DC
0V
DC
X3***
RD
BK
BN
BU
DC
0V
DC
X3***
Presence Sensor
Set X3 to a value of 6-Reverse
See X7 note
X6***
DC
0V
DC
Sensor
Control Box
RD
BK
WH
GN
not used BN
not used BU
Sensor
not used NC
NO
COM
POWER*
POWER*
PHOTOEYES
RADIO CONTROL
PUSHBUTTONS
& PULL-CORDS
Control Box
Photoeye
DC
0V
DC
X6***
BN
Control Box
Receiver
Control Box
Switch
BU
DC
0V
DC
X6**
RD
BK
WH
GN
DC
X6**
SW
SW
BK
OG
Retroreflective or Thru Beam Receiver
1. SET SWITCH TO:
DARK = ACTIVATION
OR
LIGHT = REVERSE
PHOTOEYES
Control Box
Photoeye
DC
0V
Wire Each device as shown.
BN
BU
Sensor Monitoring
MISCELLANEOUS
ACTIVATION
Thru Beam Emitter
Control Box
Door1
not used
not used
not used
not used
YDC2
DC
Standard configuration is combined mode with DIP switches
#1-9 in the OFF position and DIP switch #10 in the ON position.
For independent mode and other DIP switch settings, consult the
BEA Matrix D12-24 User Manual.
OPEN
STOP
Door2
X0
DC
X?
DC
X4
DC
Note: Consult i-COMM manual to see
which inputs can be assinged STOP
function. Connect STOP to whichever
input is selected to become STOP. No
other devices should be connected to
this input. Terminal Must be assigned
to STOP through i-COMM menu on
both doors. (i.e. If X3 is to be assigned
a function of STOP, the menu ("Input
Func X3") should be set to a value of
"1").
Control Box
Host (Receiver)
DC
DC
0V
X6**
5
6
7
4
6
7
6
7
24V
0V
8
9
8
9
LZR-i30 Presence Sensor
BEA - LZR-i30
No Sensor Monitoring
Control Box
10
SAFETY
Fault
not used
not used
not used
not used
Remote
Pairing
RF Com
Pairing:
1
2
3
4
5
OPEN CLS STOP O/C COM
1
2
3
4
Sensor
DC
0V
DC
X3
10
ACTIVATOR
2.4GHz Wireless Activation
RD
BK
GRN/WH
BLK/WH
GRN
WH
ORG
ORG/BLK
WH/BU
BU
For sensor monitoring connect WH/BU
wire to YDC2. The input must be
changed to 19 - LZR In N/C.
Set LZR relay 2 to NC.
CLSG RE BKWY
POWER
Sensor
DC
0V
DC
X3
OPEN/CLOSE/STOP
WIRELESS
PUSHBUTTON STATION PUSHBUTTONS & PULL-CORDS
CLOSE
433MHz Radio Control
1. SET DIP SWITCHES 1&2 TO OFF.
2. PRESS AND HOLD LEARN W/NO DELAY
WHILE REPEATEDLY PRESSING
TRANSMITTER BUTTON UNTIL BLUE
LED ON RECEIVER ILLUMINATES.
BEA IS40 Motion/Presence Sensor
IS-40 Hold Open
Set X3 to a value of (6-Reverse)
See X7 note
B
Beacon/Strobe
120VAC ALARM
Control Box
Alarm
STB
N
Wire
Wire
PREANNOUNCE RELAY
STB
N
Wire
Wire
Warning Device Strobe
Additonal Relay Required
120VAC U.L. Listed .30 Amp Max
Warning Device Strobe
Additonal Relay Required
120VAC U.L. Listed .30 Amp Max
J4-7
or DC
J4-12
or YDC_
STB
F7 or L
7147
6/1/2016
MDM
RADIO CONTROL CLARIFICATION
7191
7/19/2016
MDM
f
ADD MS09 AND PHOTOEYE SWITCH INF
7197
8/24/2016
MDM
5
To pair with a wireless device, first remove the
plastic strip under the batteries in the remote unit
to energize the device. On the Host (Receiver)
press "Remote Pairing". The "RF Com" LED will
begin to flash. Next press the pair button on the
remote unit. The units will then pair. Activate the
door to test. Repeat procedure if necessary.
0V
DC
Door2
Door1
YK0
YK0N
X3
DC
X3
DC
YK0
YK0N
DC
X3
YK0
YK0N
YK1
YK1N
2 Door Non-Sequential Interlock
RD
BK
GRN/WH
BLK/WH
GRN
WH
ORG
ORG/BLK
WH/BU
BU
PREANNOUNCE
DEVICES
YK1 YK1N
Door2
Door3
DC
YK1 YK1N
DC
YK2 YK2N
YK2 YK2N
REQUIRED I/O SETTINGS:
X3 = 0 Interlock In (Must be on to open)
YK0 = 0 Interlock Out (On when door closed)
YK1 = 0 Interlock Out (On when door closed)
YK2 = 0 Interlock Out (On when door closed)
Air Curtain
YK0
YK0N
Ouput
Output Com
X3
4 Door Non-Sequential Interlock
Only 1 door may be open at a time.
AIR CURTAIN
INTERLOCK (120V)
Relay
14(3)
11(4)
Note: Consult i-COMM manual for
available output functions. Connect
YK0 & YK0N to Air Curtain control.
Change YK0 to 1 (on when door not
closed).
SEQUENTIAL
INTERLOCK
Air Curtain
Door1
Door2
Ouput
Output Com
YK0
YK0N
X3
DC
DC
X5
YK1
YK1N
X3
DC
YK0
YK0N
YK1
YK1N
DC
X5
i-COMM
A1(5)
A2(1)
DC
YDC_
A1(5)
A2(1)
14(3)
11(4)
Note: Consult i-COMM manual for
available output functions. Connect
relay contact to Air Curtain control.
Change YDC_ to 1 (on when door
not closed). Separate relay must be
used for isolation with 120VAC.
INTERLOCKS
Terminals "X6", "X7" are automatic reclose.
Terminal X7 on the motor terminal strip can be used for activation devices such as motion sensors and pull cords.
Terminals "DC" are DC common for inputs.
ITEM
INCH TOLERANCES
OVER
UP TO
+/-
Note: Activation of Door 1 will
automatically activate Door 2 (and
vice versa) after the first door has
closed. Sequence resets after
both doors have cycled once.
DESCRIPTION
PART NO.
0
0.125
0.25
1.25
5
15
40
80
0.125
0.25
1.25
5
15
40
80
-
ANGLES
FINISH
+/- 1 DEG
0.005
0.010
0.020
0.030
0.040
0.060
0.100
0.125
C 2012
4
RITE-HITE
R
RITE-HITE
DO NOT SCALE DRAWING
DRAWN BY
TAH
DATE
3
A
TITLE
6/11/2012
CHECKED BY
DATE
APPROVED BY
DATE
SPLITSECOND SERIES
ACTIVATION WIRING
i-COMM II
INITIAL ECN
6522
6/11/2012
SIZE
D
REF
DOORS INC.
R
DOORS INC.
MM-DD-YY
DATE ISSUED
5
2 Door Sequential Interlock
REQUIRED I/O SETTINGS:
X3 = 0 Interlock In
X5 = 5 Sequential Activation In
YK0 = 0 Interlock Out
YK1 = 16 Sequential Act. Out
SCALE
2
MODEL NUMBER
SplitSecond
9"=1'
DWG NO
REV
F
7802E012
PART #
SHEET
1
49
Side Rolling Door
Consult i-COMM manual and/or Door manual for additional instructions.
6
QTY
B
PARTS LIST / MATERIAL
**For true toggle operation use terminal "X5".
(Pull cords, push button or radio controls only.)
***For Reverse hold open connect sensors to UNUSED input.
(i.e. X3, X6, or X7 and assign that input a function of "6" in the i-COMM menu. Multiple sensors can be connected in parallel.
7
YK0
YK0N
YK1
YK1N
YK2
YK2N
DC
X3
YK1 YK1N
X3
C
Door4
YK0 YK0N
YK0 YK0N
Control Box
X3
DC
NON-SEQUENTIAL 4 DOOR INTERLOCK
DC
X3
YK0
YK0N
YK1
YK1N
YK2
YK2N
LZR-i30 Presence Sensor
YK0
YK0N
YK1
YK1N
DC
X3
YK0 YK0N
REQUIRED I/O SETTINGS:
X3 = 0 Interlock In (Must be on to open)
YK0 = 0 Interlock Out (On when door closed)
YK1 = 0 Interlock Out (On when door closed)
Door1
Set X3 to 15 - Reverse NC. Set LZR
relay 2 to NC.
Door3
3 Door Non-Sequential Interlock
Only 1 door may be open at a time.
NOTES
This drawing assumes input functions are set to factory defaults. WARNING - never connect motion sensors to a toggle input.
8
APPROVED
D
Door2
INSTALL SPDT RELAY IN CBOX
DC COIL
A
BY
BEA LZR CLARIFICATION
E
NON-SEQUENTIAL
3 DOOR INTERLOCK
Door1
Note: Consult i-COMM manual to
see which inputs can be assigned
interlock in function. Connect YK0
to whichever input is selected to
become interlock in. No other
devices should be connected to
this input. Terminal must be
assigned to Interlock through
i-COMM menu on both doors. (i.e.
If X3 is to be assigned a function of
Interlock Input, the menu ("Input
Func X3") should be set to a value
of "0")
Output YK0 (K0 relay) should
remain at the default setting of "0"
on both doors.
WARNING DEVICE RELAY
CONTROL BOX WIRING
DATE
Installation/Owner's Manual SplitSecond™
120V STROBE
ECN
D
NON-SEQUENTIAL
2 DOOR INTERLOCK
AIR CURTAIN
INTERLOCK (24V)
Control Box
DESCRIPTION
BEA - LZR-i30
RD
BK
WH
GN
not used YE
DC
WH/BLK
GRN/BLK
X3***
not used YE/BLK
BEA ACTIVATION
BEA Motion Sensors
*Power slots are interchangable
See X7 note
BEA MATRIX
INDUCTION LOOP
Sensor
DC
0V
DC
X6***
Presence Sensor
Set X3 to a value of 6-Reverse
See X7 note
MS09
Control Box
BEA - IS-40
BEA - DK-12
Control Box
BEA Motion Sensors
See X7 note
C
1
REV
SHEET
Rite-Hite®
3
4
MAINTENANCE
5
6
Wiring Diagrams Continued
7
INDUCTION LOOP
CONTROLLER
Publication: AMEN00047 2017-03-06
Activation
8
SplitSecond™ Side Rolling Door PARTS
8 8
7
Control Box
7 7
6
6 6
5
5 5
4
4 4
3
FINAL ASSEMBLY
FINAL ASSEMBLY
NEXT ASSEMBLY
NEXT ASSEMBLY
BLY
Installation/Owner's ManualRite-Hite®
7802E009/11
7802E009/11
-
-
17
22
20
2
13 18 21
D D
R
R
R
CR1 CR3
X1
N.O. 3
X2
4
N.O. 3X1
X1
(OPEN BUTTON)
15
N.O. 3
BUTTON)
(OPEN(OPEN
BUTTON)
16
OV A1 10V A2
CLASS
II VOLTAGE
LOW 6mm
VOLTAGE
CLASS
II LOW
ONLYONLY
! T1 T2 T3!
CLASS
II
X2
4X2LOW4 VOLTAGE ONLY !
B1
B2
B3
B4
T4
T5
T6
B5
B6
B7
CR1 CR1
CR3 CR3
6mm
1
10mm
Loop sens. Adj.
Detect
Pres. Time Adj.
1 min to
NO
DELAY
Detect
F2
F2
F3
F3
F4
F2
F3F1
F3
F4F2
F7
F4
F7
F7
F3
F4
1 2
COM NO NC
12-24VAC/DC
F4
F5
H4
F7
F7
F5
HIGH VOLTAGE ONLY !
HIGH VOLTAGE ONLY !
X2
26 24
27 29
X1
31 32
CONFIGURATION
575V575V
CONFIGURATION
USE CLASS CC
FUSES ONLY
USE CLASS CC
FUSES ONLY RATED 600V, 30A
RATED 600V, 30A
F1
H3
T1
COM NO NC
ON
HOLD
TIME
1 2
ON
POWER
F1
H2
PE
12-24VAC/DC
DELAY
LEARN
NO
DELAY
LEARN
DELAY
LEARN
POWER
ACT
10RD433
LEARN
ACT
1 2
HOLD
TIME
10RD433
NO
DELAY
DELAY
ON
ACT
LEARN
LEARN
10RD433
HOLD
TIME
PUL | TOG
0.5s | 10s
12-24V
AC/DC
COM
NO
NC
COM NO NC
12-24V
AC/DC
COM
NO
NC
12-24VAC/DC
12-24V
AC/DC
COM
NO
NC
POWER
PUL | TOG
PUL | TOG 0.5s | 10s
0.5s | 10s
F1
5 14
A A
F1
F2
USE CLASS CC
FUSES ONLY
RATED 600V, 30A
Loop sens. Adj.
Pres.Adjust
Time Adj.
Freq.
1 min to
Relay A,B
Act / Pass
ASB
Relay A Pres. / pulse
Relay A Entry / Exit
Freq. Adjust
Relay B Pres. / pulse
/ Exit
Relay
B A,BEntry Act
Relay
/ Pass
Pulse
ASB 100ms / 500ms
NotRelay
UsedA Pres. / pulse
Relay A Entry / Exit
Relay B Pres. / pulse
Relay B Entry / Exit
Pulse 100ms / 500ms
Not Used
Power
Detect
Power
8
Freq. Adjust
Loop sens. Adj.
Pres. Time Adj.
1 min to
Relay A,B
Act / Pass
ASB
Relay A Pres. / pulse
Relay A Entry / Exit
Relay B Pres. / pulse
Relay B Entry / Exit
Pulse 100ms / 500ms
Not Used
8
Power
8
F1
PE
F1
F2
USE CLASS CC
FUSES ONLY
USE CLASS CC
RATED 600V, 30A
FUSES ONLY
RATED 600V, 30A
F2
F3
F3
F4
F7
F4
F7
INCH TOLERANCE
OVER
UP TO
220V
9
5
575V
5 12
SCOPE
THIS DRAWING COVERS DOORS
CONFIGURED AFTER 06/18/2012
VERIFY THAT THIS DRAWING HAS NOT BEEN SUPERCEDED BY NEWER REVISION. ABOVE APPLIES
ONLY WHEN DRAWING IS CURRENT.
PRIOR
8 8
6
7 7
5
6 6
4
0
0.125
0.25
1.25
5
15
40
80
0.125
0.25
1.25
5
15
40
80
-
ANGLES
FINISH
+/- 1 DEG
N/A
C 2012
7
GND
GND
9
W
GND
GND
U
GND
V
GND
WU
STBV
N
W
N
STB
BRK
N
N
BRK
F4
6
V
U
V
W
STBU
NV
NW
STB
BRK
XX4N
XX1N
BRK
XH2
XX4
XH1
XX1
XH2
XH1
F3
USE CLASS CC
FUSES ONLY
USE CLASS CC
USE CLASS CC
FUSES ONLY
RATED 600V, 30A
FUSES ONLY
RATED 600V, 30A
RATED 600V, 30A
U
V
W
STB
N
N
GND
BRK
GND
XX4
GND
XX1
GND
UXH2
GND
VXH1
WGND
STBU
NV
NW
STB
BRK
N
N
BRK
F2
USE CLASS CC
FUSES ONLY
USE CLASS CC
FUSES ONLY RATED 600V, 30A
RATED 600V, 30A
F7
GND
GND
GND
U
V
W
STB
N
N
BRK
F1
5
1 CONFIGURATION
575V CONFIGURATION
220V220V
1 CONFIGURATION
220V 1 CONFIGURATION
USE CLASS CC
FUSES ONLY
RATED 600V, 30A
10 11 12
4
10
8
3
9
10
23
10
+
X3
19
U
USE CLASS CC
USE CLASS CCFUSES ONLY
FUSES ONLYRATED 600V, 30A
RATED 600V, 30A
B B
USE CLASS CC
FUSES ONLY
RATED 600V, 30A
10
USE CLASS CC
USE CLASS CCFUSES ONLY
FUSES ONLY RATED 600V, 30A
RATED 600V, 30A
HIGH VOLTAGE
ONLY
!
HIGH
VOLTAGE
ONLY
1
8
9
T3
9
T2
T3
9
T1
T2
RE BKWY
T1
7
8
-
F7
F5
8
SAFETY
F4
8
F3
CLSG
USE CLASS CC
FUSES ONLY
RATED 600V, 30A
L3
F2
7
7
T3
F1
7
T2
L1
RATED 600V, 30AL2
L2
L3
0V
L1 L2 L3
3 208-240V,
460-480V,
575V
3 208-240V,
460-480V,
575V
GND
GND
GND
U
V
W
STB
N
N
BRK
T1
USE CLASS CC
FUSES ONLY
L1
6
L3
6
6
L2
6
Remote
SAFETY
5
APEMs
APEMs
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
H1
L1
24V
RS 485
25
(DISCONNECT
SWITCH)
(DISCONNECT
SWITCH)
POWER
Fault
ACTIVATOR
Pairing
RF Com
WIRELESS
HOST
5
COM
24V
0V CLSG RE BKWY
WIRELESS
HOST
4
28
POWER
3
ON
ON
23
3 208-240V, 460-480V, 575V
(DISCONNECT SWITCH)
Fault
1
2
3
4
5
Remote
OPEN CLS STOP O/C COM
Pairing
RF Com
2
10
10
APEMs
1 2 3 4 5 6 7 8 9 10
ACTIVATOR
22 3 3 4 4 5
9
9
1
8
7
1
1
8
ON
OPEN CLS STOP O/C
7
CLSG
RE BKWY
7
6
0V
5
COM
Remote
Pairing
5
SAFETY
6
4
4
WIRELESS HOST
Fault
RF Com
3
3
24V
2
2
ACTIVATOR
C C
POWER
1
- PLC LOGIC INPUTS & OUTPUTS ON PLC
1
OPEN CLS STOP O/C
- PLC LOGIC - PLC LOGIC INPUTS & OUTPUTS ON PLC
INPUTS & OUTPUTS ON PLC
5 5
RITE-HITE
R
DOORS INC.
3
4 4
50Publication: AMEN00047 2017-03-06
Rite-Hite®
Installation/Owner's Manual SplitSecond™
Side Rolling Door
PARTS
Control Box Continued
#
QTY
DESCRIPTION
PART #
1
1
Ass'y (C-Box, BackPanel, Enclosure w/labels)
1753
2
2
Bracket, Mount, Enclosure, Stainless
14501154
3
2
Fuse, .5 amp, 600V Time Delay (400-575V)
51000001
4
1
Fuse, 2 amp, 250V Time Delay
51000002
5
1/2
Fuse Holder, 2 Pole, 600V, 30A (3Ø-1; 1Ø-2)
51000003
6
1
Fuse Holder, 1 Pole, 300V, 12A
51000004
7
1
Controller, Ind Loop, Dual
17500010
8
1
Fuse Holder, 3 Pole, 600V, 30A (not 220V or 575V)
51000013
9
2
Fuse, 1 amp, 600V, CC, Time Delay (208-230V)
51000023
10
3
Fuse, 10 amp, 600V, CC, KLDR (400-460V)
51000033
11
3
Fuse, 15 amp, 600V, KLDR (208-230V)
51000051
12
3
Fuse, 6A, 600V, CC, KLDR (575V)
51000055
13
1
Kit, Warning Device Relay, i-COMM ii
53700862
14
2
Fuse, 20 amp, 600V, KLDR (220V 1Ø)
51950077
15
1
Kit, Inv, 2HP, 460V, 3PH, CNT TCH
53700990
16
1
Kit, Inv, 2HP, 230V, 1-3PH, CNT TCH
53700989
17
1
Kit, i-COMM ii, Replacement
53700860
18
1/1
Relay, SPDT,24VDC,10AMP (warn device & brake)
66450014
19
1
Kit, Disconnect Switch, w/ Handle
53700567
20
1
Kit,Resistor,Inverter,230V,2HP
66550004
1
Kit,Resistor,Inverter,460V,2HP
66550005
21
1/1
Socket, Relay,1Pole,250VAC,10AMP (W.D. & Brake)
70350002
22
1
Switch, Push Button, Ext, Green, Illum, 22MM
72700258
23
1
Terminal, End Barrier, Fuse Holder
73100019
24
4/6
Terminal, End Stop, Screwless
73100024
25
1
Terminal, WA, Cage, 20A, Jump, 2P
73100081
26
1
Power Supply, DIN, 24VDC, 30W, CG
65700007
27
7
Terminal, WA, Cage, 20A, 3 Hole
73100085
28
1
Terminal, WA, Cage, 20A, 3 Hole, Barrier
73100086
29
3
Terminal, WA, Cage, 20A, 3 Hole, GND
73100087
30*
1
Transformer, 2.0KVA, 600V: 240/120
73550017
31
1
Transformer, 150VA, 208/230/460V:24/115
73550029
32
1
Transformer, 150VA, 380/415/575V:24/115
73550030
See Activation Page for activation devices
*Not Shown
Publication: AMEN00047 2017-03-06
DWG# 7802E008L
51
SplitSecond™ Side Rolling Door Installation/Owner's ManualRite-Hite®
PARTS
Sideframe
23
29
9
28
13
1
26
11
7
3
14
27
5
22
10
20
16
17
6
25
15
2
12
8
18
24
4
19
21
52Publication: AMEN00047 2017-03-06
Rite-Hite®
Installation/Owner's Manual SplitSecond™
Side Rolling Door
PARTS
Sideframe Continued
#
QTY
1
2
DESCRIPTION
PART #
1
Sideframe, Top Shaft Support Bracket, Splt
14501142
1
Sideframe, Top Shaft Support Bracket, Spltph
14501143
2
Sideframe, Btm Shaft Support Bracket,Splt
14501148
2
Sideframe, Btm Shaft Support Bracket, Spltph
14501149
3
3
Header, Upper Wall Mount Bracket
14501167
4
1
Cable Assembly, Control Box,Splt/ph
1552
5
1
Motor Cable
15650156
6
1
Cable Assembly, Cover, Drive,Splt/ph
15650246
7
2
Cable, Cover, Non-Drive,Splt/ph
15650247
8
2
Sideframe Front Cover, Fabric/stnls
1933
9
a/r
Wire Nut, Lever, 2 Pole,28-12awg
51950079
a/r
Wire Nut, Lever, 5 Pole,28-12awg
51950081
10
1
Curtain Roller Tube Spring, Hub, Upper, Right
52940004
11
1
Curtain Roller Tube Spring, Hub, Upper, Left
52940005
12
2
Curtain Roller Tube Spring, Hub, Bottom
52940001
2
Screw, Bearing Hub, SplitSecond
67920009
2
Screw, Bearing Hub, SplitSecond Pharma
67920010
1
Header Assembly, Painted
5225
1
Header Assembly, Stainless
5226
2
Kit, Tension Arm, Splt
53700732
2
Kit, Tension Arm, Spltph
53700733
2
Cable, Tension Arm, Splt
15700018
2
Cable, Tension Arm, Spltph
15700019
1
Kit, Spring Ass'y, Left, Splt
53700718
1
Kit, Spring Ass'y, Left, Spltph
53700719
16
2
Label, Warning, Stand Clear 2 x 9
53850516
17
2
Sideframe Latch
54150023
18
2
Photoeye Receiver (Drive, Int)
63900052
19
1
Photoeye Receiver (Drive, Ext)
63900054
20
2
Photoeye Source (Non-Drive, Int)
63900057
21
1/1
Curtain Roller Tube Spring Assembly
6752
1
Curtain Roller Tube Spring, Hub, Center
52940008
1
Kit, Spring Ass'y, Right, Splt
53700720
1
13
14
15
22
23
24
Kit, Spring Ass'y, Right, Spltph
53700721
1/1
Sideframe, Set/RH/LH (Powered Coat, Fabric)
6823
1/1
Sideframe, Set/RH/LH (S.S.)
6824
1/1
Sideframe, Shell, Set/RH/LH
6825
1
Sprocket, Idler, 1/2" Bore, w/Bearing (Painted)
70800028
1
Pulley, Plastic, Flat belt, 4.5OD x 1" Crn (S.S.)
65750027
1
Kit, SPLT, Membrane Switch
53700731
a/r
Tie, Cable Mount, 1 x 1, PSA
55290009
1
Clamp, Ribbon Cable, 1"
16700045
25
1
Photoeye Source (Non Drive, Ext)
63900053
26
1/1
Sideframe Seal, Curtain Back
6831
Sideframe Fabric Cover Support Tube
7240
Velcro, PSA, Hook, Blk, 2"
74000020
Header Photoeye Cable (d.o.w.+5')
1565022
27
2
28
a/r
29
1
Publication: AMEN00047 2017-03-06
53
SplitSecond™ Side Rolling Door Installation/Owner's ManualRite-Hite®
PARTS
Trolley
LH
1
2
4
7
5
3
#
QTY
DESCRIPTION
PART #
*
1
KIT,SPLT,TRLY,ASSY,RGT
53700707
*
1
KIT,SPLTPH,TRLY,ASSY,RGT
53700708
*
1
Kit, SPLT, TRLY, Assy, LFT
53700706
*
1
Kit, SPLTPH, TRLY, Assy, LFT, R-DRV
53700709
*
1
Kit, SPLTPH, TRLY, Assy, LFT, L-DRV
53700710
1
5
Nut, Hex, 3/8 -16, znc
55630003
4
Screw, HHMS, 3/8-16 x 1 1/4”, GR5, znc
67880004
6
8
5
4
or
7
9 10
RH
4
5
4
6
5
2
7
3
2
3
7
or
8
9 10
4
Washer, Lock, Split, 3/8, znc
74130002
6
Nut, Hex, 3/8-16, ss
55630006
4
Screw, HHMS, 3/8-16 x 1 1/4”, GR5, stnls
67880032
4
Washer, Lock, Split, 3/8, ss
74130009
2
4
Urethane Roller, 2.50” OD
75550006
3
4
Retaining Ring, Ext, .669 Shaft x .035
67020006
3
5
Urethane Roller, 1.125” OD
67200033
5
Spacer, Roller
70450068
1
Screw, SHCS, 5/16-18 x 1”, znc
67870028
4
5
Urethane Roller, 1.125” OD
67200033
5
5
Spacer, Roller
70450068
6
4
Screw, SHCS, 5/16-18 x 3/4”, znc
67870090
7
3
Screw, SHCS, 5/16-18 x 3/4”, znc
67870090
8
a/r
Washer, Lock, Split, 5/16, znc
74120002
9
a/r
Washer, Lock, Split, 5/16, ss
74120006
10
a/r
Screw, SHCS, 5/16-18 x 1”, ss
67870062
*Not Shown
1
54Publication: AMEN00047 2017-03-06
Rite-Hite®
Installation/Owner's Manual SplitSecond™
Side Rolling Door
PARTS
Drive System
10
DESCRIPTION
PART #
1
Header, Pillow Block Bearing, SC, 1" Bore
12500018
1
Bushing, Taper Lock, Int Key, 1x1" Bore
15550057
3
1
Kit, Splt/ph, Brake Release Latch w/cable
53700742
9
4
1
Kit, Splt/ph, Brake Rls Cable
53700772
1
Kit, Splt/ph, Bake Rls Rope
53700773
1
Cable Clamp, 2 Bolt, 3/32
16700044
5
5
1
Kit,Splt,Encoder
(units <= 11/15/2010 require one of the
encoder cables)
53700793
1
Encoder Cable 4M
15650256
1
Encoder Cable 8M
15650257
1
Encoder Cable 17M
15650258
1
Motor Assembly
5537
1
Motor/Brake/Gearbox, 230/460V, 7.5:1
55250157
1
Motor/Brake/Gearbox, 400V, 7.5:1
55250158
1
Motor/Brake/Gearbox, 575V, 7.5:1
(<9/27/10)
55250159
1
Plate, Motor, Spacer, Splt
65000706
1
Plate, Motor, Spacer, Spltph
65000707
1
Encoder, Mounting Plate
65000708
1
Encoder, Mounting Plate, Spltph
65000709
11
1
7
2
12
8
6
4
#
QTY
1
2
6
7
8
3
9
2
Retaining Ring, Ext, 1.0 Shaft, x .042
67020016
10
1
Motor Drive Shaft
68950171
11
2
Header, Pillow Block, Spacer, SPLT
70450135
2
Header, Pillow Block, Spacer, SPLTPH
70450136
1
Sprocket, #40, 24T, Taper Lock (Painted)
70800049
1
Sprocket, Polychain, GT, 8MX-21, 34T
70800050
12
Drive Chain
1
#
QTY
1
2
3
2
DESCRIPTION
PART #
1
Header Chain Turnbuckle (Painted)
73950010
1
Header Chain (Painted)
16600033
1
Clamp, Chain, Top, Splt
16700046
1
Clamp, Chain, Bottom, Splt
65000668
Publication: AMEN00047 2017-03-06
3
55
SplitSecond™ Side Rolling Door Installation/Owner's ManualRite-Hite®
PARTS
Drive Belt
2
4
3
5
6
2
4
3
8
9
4
1
7
#
QTY
DESCRIPTION
PART #
1
4
Screw, HHMS, 5/16-18 x 1 1/2”, ss
67870060
2
4
Screw, HHMS, 5/16-18 x 3/4, ss
67870085
3
4
Clamp, Belt, Flat, (Pharma)
16700047
4
1
Header Belting (Specify Timing or Flat) S.S.
1264
5
1
Plate, Clamp, Belting (Pharma)
65000250
6
1
Plate, Clamp, Belting (Pharma)
65000679
7
4
Clamp, Belt, Top, (Pharma)
16700048
8
1
Tensioner, Belt, SpltPH
73000033
9
2
Nut, Hex, 1/2-13, S.S.
55650008
56Publication: AMEN00047 2017-03-06
Rite-Hite®
Installation/Owner's Manual SplitSecond™
Side Rolling Door
PARTS
Parts Box – Steel Covers
4
14
3
2
Parts Box – Fabric Covers
8
1
1
3
16
8
2
13 14
4
6
17
15
13
5
10
5
18
6
11
17
9
QTY
1
DESCRIPTION
PART #
4
Screw,HHMS,3/8-16X1-1/4,Gr5,znc
67880004
2
4
Washer,Lock,Split,3/8,znc
74130002
3
4
Nut,Hex,3/8-16
55630003
4
8
Screw,BHMS,Sckt,Flg,1/4-20X.5,ss
67860127
5
20
Screw,Shcs,#8-32X1-1/4
67850161
6
6
Screw,Set,Sckt,Cup,#10-24X1/4
67850163
7
15
Tie,Cable,Nylon,4",18#
73250004
8
8
Screw,Fhms,Sckt,1/4-20X3/8
67860126
9
2
Washer,Lock,Split,#6, znc
74100013
10
2
Screw,Rhms,Philip,#6-32 X 3/8,znc
67850022
11
1
Pe,Assy,Rcvr,Splt/Ph
63900054
12
1
Pe,Assy,Src,Splt/Ph
63900053
13
3
Screw,HHMS,1/4-20X1/2,Gr5,znc
67860002
14
3
Screw,HWH,Slf Dr/Tp,#12-14X3/4
67850004
15*
2
Cover,Tension Arm
17900166
16
3
Washer,Flat,1/4X3/4X1/16,znc
74110001
17
1
1 Kit, Splt, Encoder
53700793
18
1
Wrench,Hex,L-Key,2mm,Long Arm
*Not Shown
Publication: AMEN00047 2017-03-06
12
18
12
#
11
7
#
QTY
1
2
9
3
2
1
7
10
DESCRIPTION
PART #
8
Screw,Hhms,3/8-16X1-1/4,Gr5,znc
67880004
8
Washer,Lock,Split,3/8,Znc
74130002
3
8
Nut,Hex,3/8-16
55630003
4
8
Screw,Bhms,Sckt,Flg,1/4-20X.5,ss
67860127
5
20
Screw,Shcs,#8-32X1-1/4
67850161
6
6
Screw,Set,Sckt,Cup,#10-24X1/4
67850163
7
15
Tie,Cable,Nylon,4",18#
73250004
8
8
Screw,Fhms,Sckt,1/4-20X3/8
67860126
9
2
Washer,Lock,Split,#6, znc
74100013
10
2
Screw,Rhms,Phlp,#6-32 X 3/8 znc
67850022
11
1
Pe,Thrbm,Rcvr,Rs,11-30 Vdc
63900052
12
1
Pe,Thrbm,Src,Rs,11-30 Vdc
63900051
13
3
Screw,Hhms,1/4-20X1/2,Gr5,znc
67860002
14
3
Washer,Flat,1/4X3/4X1/16,znc
74110001
15
2
Brkt,Mnt,Pe,Fabric,Splt
14501168
16*
2
Cover,Tension Arm
17900166
17
1
Kit, Splt, Encoder
53700793
18
1
Wrench,Hex,L-Key,2mm,Long Arm
*Not Shown
55150247
DWG7802M292D
55150247
DWG7802M291E
57
SplitSecond™ Side Rolling Door Installation/Owner's ManualRite-Hite®
PARTS
Parts Box – Pharma Covers
1
3
Shroud
8
2
13
14
1
4
5
16
17
12
#
QTY
1
11
6
9
7
19
10
#
QTY
1
2
DESCRIPTION
PART #
4
Screw,Hhms,3/8-16X1-1/4,ss
67880032
2
4
Washer,Lock,Split,3/8,ss
74130009
3
4
Nut,Hex,3/8-16,ss
55630006
4
8
Screw,Bhms,Sckt,Flg,1/4-20X.5,ss
67860127
5
20
Screw,Shcs,#8-32X1-1/4,Ss
67850162
6
6
Screw,Set,Sckt,Cup,#10-24X1/4,ss
67850164
7
15
Tie,Cable,Nylon,4",18#
73250004
8
8
Screw,Fhms,Sckt,1/4-20X3/8,stnls
67860125
9
2
Washer,Lock,Split,#6,stnls
74100023
10
2
Screw,Rhms,Phlp,#6-32 X 3/8,ss
67850171
11
1
Pe,Assy,Src,Splt/Ph
63900053
12
1
Pe,Assy,Rcvr,Splt/Ph
63900054
13
5
Screw,Hhms,1/4-20X1/2,ss
67860056
14
5
Washer,Flat,5/16X3/4X0.05,ss
74120005
15*
2
Cover,Tension Arm
17900166
16
1
Kit, Splt, Encoder
53700793
17
1
Wrench,Hex,L-Key,2Mm,Long Arm
55150247
18
1
Screw,Hhms,5/16-18X3/4,stnls
67870085
19
1
Washer,Flat,5/16X3/4X0.05,ss
*Not Shown
2
18
DESCRIPTION
PART #
1
Header Shroud, Fabric
1935
1
Header Shroud, SplitSecond/Pharma
6946
1
Kit,SPLT,Shroud,R-DRV,Flat
53700724
1
Kit,SPLT,Shroud,L-DRV,Flat
53700725
1
Kit,SPLT,Shroud,L-DRV,SLPD,BLK
53700726
1
Kit,SPLT,Shroud,L-DRV,SLPD,stnls
53700727
1
Kit,SPLT,Shroud,R-DRV,SLPD,BLK
53700728
1
Kit,SPLT,Shroud,R-DRV,SLPD,stnls
53700729
Seals
1
2
3
4
5
74120005
DWG7824M246E
#
QTY
DESCRIPTION
PART #
1
4
Bracket, Lintel Seal, SPLT
14501163
4
Bracket, Lintel Seal, SPLTPH
14501164
2
2
Header Lintel Seal
6833
a/r
Brush. Weatherstrip
15000001
3
2
Seal, Ultra, Rear Sideframe corner
6829
4
1
Seal, Sideframe, Non-Drive, SPLT
68350160
5
1
Seal, Sideframe, Drive, Left, SPLT
68350161
1
Seal, Sideframe, Drive, Right, SPLT
68350162
1
Ultra Seal Upgrade
6828
58Publication: AMEN00047 2017-03-06
Rite-Hite®
Installation/Owner's Manual SplitSecond™
Side Rolling Door
PARTS
Curtain
7
1
#
QTY
DESCRIPTION
PART #
1
1
Curtain Hanger Weldment, RH (Painted)
51900073
1
Curtain Hanger Weldment, LH (Painted)
51900074
1
Curtain Hanger Weldment, RH (S.S.)
51900075
1
Curtain Hanger Weldment, LH (S.S.)
51900076
2
Curtain Breakaway Block (Painted)
13000054
2
Curtain Breakaway Block (S.S.)
13000055
2
Kit, SPLTPH, Edge, Ten Arm Block
53700738
2
Kit, SPLT, Edge, Ten Arm Block
53700739
a/r
Screw, SHCS, #8-32x1 1/4,znc
67850161
2
2
9
3
4
Screw, SHCS, #8-32x1 1/4,stnls
67850162
Screw, Set, SCKT, Cup,#10-24x 1/4,znc
67850163
a/r
Screw, Set, SCKT, Cup,#10-24x 1/4,stnls
67850164
a/r
Screw, SHCS, 5/16-18 x 2", znc
67870115
a/r
Screw, SHCS, 5/16-18 x 2", stnls
67870116
3
a/r
Kit, SPLT, Vision Patch
53700736
4
1/1
Curtain Assembly
2887
a/r
Kit,SPLT,Curtain Patch, Blu
53700734
a/r
Kit,SPLT, Curtain Patch, Wht
53700735
5
2
Sideframe Seal, Curtain Front
6832
6
2
Curtain Bottom, Seal
6834
7
2
Curtain, Leading Edge, Pivot Pin
64040028
2
Nut, Hex, Jam, 1/2-13, znc
55650005
2
Nut, Hex, Jam, 1/2-13, stnls, LH
55650018
2
Screw, HHMS, 1/2-13 x 2 1/4", GR5, znc
67900001
2
Screw, HHMS, 1/2-13 x 2 1/4", stnls
67900024
2
Curtain Leading Edge, Ass'y
4370
4
Screw, BHMS, SCKT, FLG, 1/4-20 x 1/2",ss
67860127
Seal, Rubber, Nose
68350067
Curtain Leading Edge, Tube
7241
8
5
a/r
a/r
a/r
9
8
2
6
5
Miscellaneous
Description
PART #
1
Entire Door, SplitSecond*
SPLT
1
Entire Door, SplitSecond Pharma*
SPLTPH
1
Kit, SplitSecond, Service Parts*
53700722
QTY
Kit, Bake Release,
Thru-wall (1)
PART # 53700743
*Not Shown
Bracket, BEA Falcon (a/r)
PART # 14501212
Publication: AMEN00047 2017-03-06
59
SplitSecond™ Side Rolling Door Installation/Owner's ManualRite-Hite®
PARTS
Activation
#
PART #
DESCRIPTION
5700
7100
80/XL
8600
1
11050007
2
11050010
Alarm, Audible, 24AC/DC, 22.5 (I-Zone)
N
Alarm, Audible, 120VAC,10-TONE, AB
N
3
4
17500025
Controller, Wireless, Act, BTR, 12-24V
17500001
Induction Loop Board, 24VDC (<5/28/14)
5
17500010
6
8900
FSTX
/LD
FSTX
CL
FSTX
FR
FSTX
FR LD
FSTX
XL
LTSPD
SPLIT
2ND
N
Y
N
Y
Y
Y
Y
Y
Y
Y
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
N
N
Y
N
N
Y
Y
Y
Y
Y
Y
Y
Y
N
Y
Y
Y
Y
Y
Y
Y
N
N
N
N
Induction Loop Board, 12/24VDC
(=>6/20/12)
N
Y
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
52000037
Induction Loop Board Harness (<5/28/14)
N
Y
Y
Y
Y
Y
Y
Y
N
N
N
N
7
52000056
Induction Loop Board Harness (=>6/20/12)
N
Y
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
8
53700552
Induction Loop, Kit, Single (<5/28/14)
N
Y
Y
Y
Y
Y
Y
Y
N
N
N
N
9
53700864
Induction Loop, Kit, Dual
N
Y
Y
N
Y
Y
Y
Y
Y
Y
Y
Y
10
55150279
i-COMM ii LCD Interface
N
Y
N
N
N
Y
Y
Y
Y
Y
Y
Y
11
7622
I-Zone Kit
N
N
Y
N
Y
Y
N
Y
Y
Y
Y
N
12
7637
I-Zone Upgrade Kit, FasTrax
N
N
N
N
N
Y
N
Y
Y
Y
N
N
13
14500774
I-Zone Sensor Bracket Black
N
N
Y
N
Y
Y
N
Y
Y
Y
Y
N
14
14500775
I-Zone Sensor Bracket Gray
N
N
Y
N
Y
Y
N
Y
Y
Y
Y
N
15
14500783
I-Zone Sensor Bracket Stainless
N
N
Y
N
Y
Y
N
Y
Y
Y
Y
N
16
17900110
I-Zone Cover Gray
N
N
Y
N
Y
Y
N
Y
Y
Y
Y
N
17
17900111
I-Zone Cover Black
N
N
Y
N
Y
Y
N
Y
Y
Y
Y
N
18
17900112
I-Zone Cover Stainless
N
N
Y
N
Y
Y
N
Y
Y
Y
Y
N
19
14501212
Motion Sensor, Mounting Bracket
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
20
55200012
Motion Sensor, Remote Programmer
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
21
55200018
Motion Sensor, FalconXL < 11.5'H
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
22
55200019
Motion Sensor, Falcon >= 11.5'H
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
23
55200021
Motion Sensor, IS40, 12-24V
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
24
55200022
Motion Sensor, LZRI30, 12-35VDC
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
25
55200023
Motion Sensor, MS08,Touchless, 12-24V
N
Y
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
26
55200024
Motion Sensor, IS40XL, 12-24V
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
27
55200025
MOTION SENSOR, FALCONW >=16W
N
N
N
N
N
N
N
N
N
Y
N
N
28
14500024
Photoeye Mounting Bracket
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
29
53700053
Photoeye, 24V, Kit, Thru-beam
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
30
53700122
Photoeye, 24V, Kit, Retro-reflective
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
31
66400001
Photoeye, Reflector, 2 3/4" x 2"
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
32
63900002
Photoeye, Retro-Reflective
20-40VAC/10-55VDC
N
Y
Y
Y
N
Y
Y
Y
Y
Y
Y
Y
33
69300004
Photoeye, Thru-beam Source
20-40VAC/10-55VDC
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
34
63900005
Photoeye, Thru-beam Receiver
20-40VAC/10-55VDC
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
35
63900048
Photoeye, Light Curtain, Receiver, (CE)
N
N
N
N
N
Y
N
Y
Y
N
Y
N
36
63900049
Photoeye, Light Curtain, Transmitter, (CE)
N
N
N
N
N
Y
N
Y
Y
N
Y
N
37
72700213
Pull Cord, Assembly, w/Bracket, Standard
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
38
72700214
Pull Cord, Assembly, w/Bracket, Heated
N
Y
Y
Y
N
N
Y
Y
Y
N
Y
N
39
72700270
Pull Cord, Wireless
N
Y
Y
N
N
Y
Y
Y
Y
Y
Y
Y
40
72700030
Push Button Station Single Green
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
41
72700102
Push Button Station, Open/E-Stop/Close,
Nema 4X
N
N
N
N
N
N
N
Y
Y
Y
Y
Y
42
72700269
Push Button, Single, Wireless
N
Y
N
N
N
Y
Y
Y
Y
Y
Y
Y
43
66250020
Radio Control, RCVR, BEA, 433, 12-24V,
1 FN (=>8/26/14)
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
44
73750078
Radio Control, Trans, BEA, 433, 1 BTN
(=>8/26/14)
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
60Publication: AMEN00047 2017-03-06
Rite-Hite®
Installation/Owner's Manual SplitSecond™
Side Rolling Door
PARTS
Activation Continued
#
PART #
DESCRIPTION
5700
7100
80/XL
8600
8900
FSTX
/LD
FSTX
CL
FSTX
FR
45
73750079
Radio Control, Trans, BEA, 433, 2 BTN
(=>8/26/14)
N
Y
Y
Y
Y
Y
Y
Y
46
73750080
Radio Control, Trans, BEA, 433, 3 BTN
(=>8/26/14)
N
Y
Y
Y
Y
Y
Y
47
11280002
Radio Control Ant w/15' Cable, 318 MHZ
(<8/26/14)
N
Y
Y
Y
Y
Y
48
53700068
Radio Control, 24V, Kit, 318 MHZ (<8/26/14)
N
Y
Y
Y
Y
49
66250016
Radio RCVR, 24V 318 MHZ (<8/26/14)
N
Y
Y
Y
50
66250017
Radio RCVR, 24V 300 MHZ (<8/26/14)
N
Y
Y
Y
51
73750002
Radio TRANS, 300 MHZ, BTN, 4 (<8/26/14)
N
Y
Y
52
73750015
Radio TRANS, 318 MHZ, BTN, 1 (<8/26/14)
N
Y
53
73750018
Radio TRANS, 318 MHZ, BTN, 3 (<8/26/14)
N
54
73750019
Radio TRANS, 318 MHZ, BTN, 2 (<8/26/14)
N
55
54270030
Strobe 120VAC Amber
N
FSTX
FR LD
FSTX
XL
LTSPD
SPLIT
2ND
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
N
Y
Y
Y
Y
Y
Y
N
Y
Y
Y
Y
Y
Y
Y
N
Y
Y
Y
Y
Y
Y
Y
N
Y
Y
Y
Y
Y
Y
Y
Y
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
56
54270031
Strobe 120VAC Red
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
xx
54270036
Light,Dok Lok,Assy,12/24 LED
X
X
X
X
X
X
X
X
X
X
X
X
57
53700567
Switch, Disconnect w/Handle
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
58
72700011
Switch, Selector, 2 Pos, Key
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
59
72700072
Switch, Selector, 2 Pos (Socket p/n:
17200012)
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
60
72700144
Switch, Selector, 3 Pos, 3 Pole, 12A
Y
N
N
N
N
N
N
N
N
N
N
N
61
VRTLV
Virtual Vision, Kit, Stand Alone
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
62
7623
Virtual Vision, Kit, FSTX/FR/LTSPD
N
N
N
N
Y
Y
N
Y
Y
N
Y
Y
63
7624
Virtual Vision, Kit, FSTXCL
N
N
N
N
N
N
Y
N
N
N
N
N
64
7638
Virtual Vision, Kit, FSTXXL
N
N
N
N
N
N
N
N
N
Y
N
N
65
53700862
Warning Device Kit, Relay, i-COMM ii
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
66
53700863
Warning Device Kit, Relay, PLC
N
N
Y
Y
N
N
N
N
N
N
N
N
67
53700306
Kit, Activation Service Parts (loop, pe, pull,
push)
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Publication: AMEN00047 2017-03-06
61
3
1
REV.
DATE
DESCRIPTION
ECN
BY
A
6/29/2010
RELEASE
6135
SHC
UPPER MOUTING LOCATIONS
CAN BE RELOCATED
HORIZONTALLY ALONG
TOP OF HEADER
D.O.W. + 23.75 (WIDTH OF HEADER)
D.O.W. + 23.75 (WIDTH OF HEADER)
17.38
1/2 D.O.W. - 2.00
B
1/2 D.O.W. - 2.00
THESE MOUTING LOCATIONS
CAN NOT BE RELOCATED
9.88
9.88
1/2 D.O.W. - 24.00
CL OF DOOR OPENING
D.O.H. + 5.19
CL OF DOOR OPENING
D.O.H. + 12.68
D.O.H.
D.O.W.
D.O.H. + 5.19
D.O.W.
SPLITSECOND PHARMA
SPLITSECOND POWDER COATED/FABRIC COVERS
A
A
FINISH
MATERIAL
CONFIDENTIAL
* DENOTES CENTER LOCATION OF MOUNTING HOLE
THIS DOCUMENT IS THE PROPERTY
OF RITE-HITE® DOORS INC. SUBJECT
MATTER HEREIN IS CONFIDENTIAL.
DO NOT USE, REPRODUCE, COPY OR
DISCLOSE EXCEPT WITH WRITTEN
CONSENT OF OF RITE-HITE®
DOORS INC.
© 2010 RITE-HITE®
DOORS INC.
4
3
UNLESS OTHERWISE SPECIFIED DRAWN BY
DIMENSIONS ARE IN INCHES.
DRAWN DATE
TOLERANCES:
INITIAL ECN
.050
=
.X
=
.010
.XX
DATE ISSUED
=
.005
.XXX
1.0
ANGLE =
THIRD ANGLE PROJECTION
6135 TITLE
SPLITSECOND HEADER MOUTING TAB LOCATIONS
06/29/2010
REFERENCE
ALL SHEETS ARE THE SAME
REVISION STATUS
DO NOT SCALE DRAWING
2
RITE-HITE ®
DOORS INC.
SHC
06/24/2010
SIZE MODEL
B
SCALE
DWG NO
SPLT/PH
1:32
PART#
-
7802M343
SHEET
1
1 OF 1
REV
A
Installation/Owner's ManualRite-Hite®
1/2 D.O.W. - 24.00
1/2 D.O.W. - 24.00
D.O.H.
B
9.88
9.88
1/2 D.O.W. - 24.00
D.O.H. + 12.74
18.00
15.63
19.75
ARCHITECTURAL DRAWINGS
REVISION HISTORY
SplitSecond™ Side Rolling Door 2
FINAL ASSEMBLY
Mounting Tab Location
62Publication: AMEN00047 2017-03-06
4
NEXT ASSEMBLY
3
4
2
1
DESCRIPTION
ECN
BY
11/9/2009
ADD CONTROL CABLE DIMENSIONS
5962
RPB
B
8/20/2010
ADD 575V XFMR NOTE
6132
RPB
C
3/7/2014
MAKE BOTTOM SEAL OPTIONAL
6857
RPB
12"
305
See note 3 & 7
13"
330
22"
559
SECTION B-B
B
3"
76
See note 5
20 1/2"
521
Consult Product Sell/Specification Sheet and
Order Form for additional product specifications
and all available options.
Drive Side
(Left or Right)
Header
B
B
Header Mounting Tabs
See note 6
Motor/Brake/Gearbox
3"
76
See note 4
Curtain
48"
1219
Door
Opening
Height
3" See note 3
76
6" MIN.
152
40"
1016
See note 2
Notes:
1.
Alternate dimensions in brackets are in millimeters.
2.
Vision height is 32" [813] for doors less than 8' [2438].
3.
Motor shroud requires min. 3" [76] of side clearance for access.
4.
Recommended sideframe installation clearance is 3" [76].
5.
Header shroud requires min. 3" [76] of top clearance for access.
6.
Mounting tabs require 3" [76] of clearance above shroud. For sloped
shroud option, tabs are located under shroud. Tabs can be relocated if
required.
7.
Optional sloped shroud increases finished header clearance to 15" [381]
above door opening height, +3" [76] additional required for installation.
8.
Fiberglass Control Box (std.) 14" [356] x 16" [406] x 8" [203] , Stainless
Control Box (opt.) 16" [406] x 19" [482] x 8" [203]. Step down transformer
provided with 575V controls 9" [229] x 10" [254] x 7" [178]
Vision Panel
APPROVED
Control Box
See note 8
54"
1372
Photo eye
41"
36"
1041
914
Photo eye
A
13 1/4"
337
Sideframe
Optional Replaceable
Bottom Seal
(Zipper Attachment)
Floor
A
DRAWN BY
12"
305
DRAWN DATE
22"
559
INITIAL ECN
© 2009 RITE-HITE®
DOORS INC.
Travel arc for
sideframe lid
4
NO
THIRD ANGLE PROJECTION
SECTION A-A
SCALE 1 : 16
DATE ISSUED
5868 TITLE
ARCHITECTURAL APPROVAL
07/23/2009 SPLITSECOND STEEL COVERS
REFERENCE
ALL SHEETS ARE THE SAME
REVISION STATUS
DO NOT SCALE DRAWING
3
2
RITE-HITE ®
DOORS INC.
RPB
03/14/2009
SIZE MODEL
B
SCALE
DWG NO
SplitSecond
1:36
PART#
7802A001
SPLT.XXXX
SHEET
1
1 OF 1
REV
C
Installation/Owner's Manual SplitSecond™
A

37"
940
12"
305
Wall
YES
Approved By:
Date:
A
B
18"
457
Photo eye

Rite-Hite®
DATE
A
ARCHITECTURAL DRAWING
REV.
Door Opening Width
Steel Covers
Publication: AMEN00047 2017-03-06
REVISION HISTORY
Side Rolling Door
63

‘˜
‘
‘˜—‘—

¢Ž˜

‘
  £˜˜—˜—

¤£
…•–…
‹





‘˜™





……
‰—’
…•‹
Œ
„

­ €‚ƒ
‘”
…
…•
„…•‹




‹

‹
 

…“…†
‘
†ƒ


‹

–††
 
…††‡‚†
ˆ†
‰Š…
‡‹ˆ
Œ
Ž†
…’ˆ
–

–˜

˜—‘
§˜™„˜¨
‘
˜†‡’
“…’ˆ†…
˜„€—¤‘˜
‘˜™
‘—
˜¥
 ˜˜—
‘„˜‘˜¥——
—˜‘„
Ž‘
——„˜˜„
˜˜¥
 ­€



 Š —
‘—
–€
†…
‡„


˜¦ —˜„¢¢¢¢ „˜
Ž
Installation/Owner's ManualRite-Hite®



†
…ˆ“…“…‚‡­
“…ˆ…††…ˆ
“

…“…‹…•‹
…“š›’“†““
‹œš›


“‹”ž”…“ˆ…š›’“…‡†‡’‡‡““

‡ˆˆ“…’ˆ…“
††
…‡†‡…“š›

„“‹”ž”…“ˆ…š›’
‡†‡’‡‡““

Ž…‚•†““‘
†ƒ‰“
Œš›ƒš›ƒš›Ÿ
…†““
‘
†ƒ‰
Œš›ƒš›ƒš›
¡
“’ˆ
…¡…
‹‡
†“š›ƒš›ƒš›
SplitSecond™ Side Rolling Door ˜
ARCHITECTURAL DRAWING

Pharma
64Publication: AMEN00047 2017-03-06
„˜

­–š

™
 £‡–

­
  ¤––˜–˜

¥¤

‘ ’‰“


 

­€
‚


‚ƒ‚
„

Œ
­
„“

‚…†
 
 
—„„
‚„„ˆ‰„
†„
Š‹‚
ˆŒ†
Ž

‡„
­€
‚
—
—–
–˜­
 
¨–š”–©
­
–”’˜¥­–
­–š
­˜
–¦
 ––˜
­”–­–¦˜˜
 ˜–­‡­­
‡­
˜˜”––”
––¦



  ­€

„
‚†ƒ‚ƒ‚‰ˆ‘
ƒ‚†‚„„‚†
ƒ

‚ƒ‚Œ‚•Œ
‚ƒ›œ…ƒ„ƒƒ
Œž›œ


ƒŒ€Ÿ€‚ƒ†‚›œ…ƒ‚ˆ„ˆ…ˆˆƒƒ

ˆ††ƒ‚…†‚ƒ
„„
‚ˆ„ˆ‚ƒ›œ

”ƒŒ€Ÿ€‚ƒ†‚›œ…
ˆ„ˆ…
ˆˆƒƒ

€
‚•
‰ƒŸ€‚›œ…ˆ„ˆ‰ƒŒ€‡
ƒ„ƒŒ€
‚¡
‰ƒ„ˆ
€ƒŒ€–‰ƒˆ
‰„ˆ
‚…Ÿ€‚

‡‚‰•„ƒƒ­
„“Šƒ
Ž›œ“›œ“›œ¡
‚„ƒƒ­
„“Š
Ž›œ“›œ“›œ
¢
ƒ…†‚¢‚
Œˆ
„ƒ›œ“
›œ“›œ
‹ ˜
­˜
—’
„‚
ˆ

–§

˜–£££
”–
‡
Installation/Owner's Manual SplitSecond™
”€
‚•–‰ƒ

Œ

”


Œ
­
­–˜­˜
‚‚
Š˜…
‚•Œ
Ž
‚•
”‚•Œ
­–





–
Rite-Hite®



ARCHITECTURAL DRAWING
‚•—‚
Œ
Fabric Covers
Publication: AMEN00047 2017-03-06
”–
Side Rolling Door
65
SplitSecond™ Side Rolling Door Installation/Owner's ManualRite-Hite®
ABBREVIATION LIST
ABBREVIATION
DESCRIPTION
ABBREVIATION
DESCRIPTION
AB
Allen Bradley
H.P.
Horse Power
AC
Alternate Current
Hz
Hertz
ACT
Activation
illum
Illumination
Amp
Amperage
ID
Inside Dimension
A/R
As Required
in
Inches
Ass'y
Assembly
ind
Induction
BL or BLK
Black
Int
Interior
BRD/DRN
Braid or Drain wire
Int/Int
Interior / Interior
BR or BRN
Brown
Int/Ext
Interior / Exterior
BRKT
Bracket
I/O
Input / Output
BRK
Brake
J-Box
Junction Box
BTM
Bottom
KBPS
Kilobytes per second
BU
Blue
KLDR
Time Delay Fuse
CC
Current Limiting
KVA
Kilo-Volt Ampere
CE
CL
European Commission
L
Left
Center Line
lb
Pounds
CL
Clean Door
LCD
Liquid Crystal Display
CLR
Cooler Door
LED
Light-Emitting Diode
CR
Control Relay
LH
Left Hand
CT
Control Techniques
LHD
Left Hand Drive
C.W.
Counter Weight
L1,2,3
Line Voltage 1, 2, 3
CUI
Compact User Interface
LLC
Limited Liability Company
DC
Direct Current
LTSPD
LiteSpeed
D.O.H.
Door Opening Height
L/S
Limit Switch
D.O.W.
Door Opening Width
M/D/Y
Month/Day/Year
DR
Drill
Max
Maximum
E-Stop
Emergency Stop
MCR
Motor Contactor
e.g.
For Example
Mhz
Mega Hertz
etc
Etcetera
Mil /mm
Millimeters
Ext
Exterior
Min
Minimum
Ext/Ext
Exterior / Exterior
Misc
Miscellaneous
FHMS
Flat Head Machine Screw
MPH
Miles per hour
F1,2,3
Fuse 1,2,3
MSDC
Mounted Side DC
FCC
Federal Communications Commission
MSTP
Mounted Side Tie Point
FHWH
Flat Head Washer Head
N
Neutral
FR / FZR
Freezer Door
NMDC
Non-Mounted Side DC
FSTX
FasTrax
NMTP
Non-Mounted Side Tie Point
GBX
Gearbox
N/A
Not Available
GN or GRN
Green
N.C.
Normally Closed
GND
Ground
N.O.
Normally Open
GR
Grade
N.P.O.
Non-Powered Opening
GY
Gray
OB
Obstruction
HDW
Hardware
O.D.H.
Ordered Door Height
HHCS
Hex Head Cap Screw
O.D.W.
Ordered Door Width
HHMS
Hex Head Machine Screw
Opt
Optional
HWHSMS
Hex Washer head Sheet Metal Screw
OR or ORG
Orange
66Publication: AMEN00047 2017-03-06
Rite-Hite®
Installation/Owner's Manual SplitSecond™
Side Rolling Door
ABBREVIATION LIST Continued
ABBREVIATION
DESCRIPTION
ABBREVIATION
DESCRIPTION
Oz
Ounce
ZNC
Zinc
Pharma
Pharmaceutical
0V
Direct Current Common (Zero V)
PB
Push Button
PE
Photoeye
PHLP
Phillips Head
PHSMS
Pan Head Sheet Metal Screw
PK
Pink
P.M.P.
Planned Maintenance Program
Pos
Position
PSA
Pressure Sensitive Adhesive
Pub
Publication
PVC
Polyvinyl Chloride
Qty
Quantity
R
Right
RD
Red
RH
Right Hand
RHD
Right Hand Drive
RHMS
Round Head Machine Screw
R/T
Roller Tube
SD
Secure Digital
SEC
Seconds
SF
Square Foot
S/F
Side Frame
SK
Control Techniques VFD
SPDT
Single Pole Double Throw
SPLT
SplitSecond
S.S. / STNLS
Stainless Steel
STND / STD
Standard
SW
Switch (Disconnect)
Term
Terminal
TIG
Tungsten Insert Gas
UHMW
Ultra High Molecular Weight Polyethylene
UV
Ultra Violet
V
Voltage
VFD
Variable Frequency Drive
VL
Vertical Lift
V.V.
Virtual Vision
W.D.
Warning Device
w/
With
w/o
Without
WH
White
X
Controller Input
XL
Extra Large Door
Y
Controller Output
YE
Yellow
Publication: AMEN00047 2017-03-06
2017-02-17
67
LIMITED PRODUCT WARRANTY SplitSecond™ Side Rolling Door
RITE-HITE Company, LLC and its affiliates (collectively "RITE-HITE") warrant that the Product sold to the Owner will be
free of defects in design, materials and workmanship (ordinary wear and tear excepted) for the periods set forth below
("Limited Warranty").
Two (2) Year on all mechanical and electrical parts.
One (1) Year labor, based on approved travel and labor repair times.
Five (5) Year for motor, brake and gearbox material failure only.
REMEDIES
Parts: RITE‑HITE's obligations under this Limited Warranty are limited to repairing or replacing, at RITE‑HITE's option, any
part which is determined by RITE‑HITE to be defective during the applicable warranty period. Such repair or replacement
shall be RITE‑HITE's sole obligation and the Owner's exclusive remedy under this Limited Warranty.
Labor: RITE‑HITE will provide warranty service without charge for labor per the specified warranty period. Thereafter, a
charge will apply to any repair or replacement under this Limited Warranty.
CLAIMS Claims under this Limited Warranty must be made (i) within 30 (thirty) days after discovery and (ii) prior to
expiration of the applicable warranty period. Warranty period commences on the date of shipment. Claims shall be
made in writing or by contacting the representative from whom the Product was purchased directly. Owner must allow
RITE‑HITE or its agent, a reasonable opportunity to inspect any Product claimed to be defective and shall, at RITE‑HITE's
option, either (x) grant RITE‑HITE or its agent access to Owner's premises for the purpose of repairing or replacing the
Product or (y) return of the Product to the RITE‑HITE, f.o.b. RITE‑HITE's factory.
NOT WARRANTED RITE‑HITE does not warrant against and is not responsible for wear items such as fuses, batteries,
bulbs, vision and seals. No implied warranty shall be deemed to cover damages that result directly or indirectly from: (i) the
unauthorized modification or repair of the Product, (ii) damage due to misuse, neglect, accident, failure to provide necessary
maintenance, or normal wear and tear of the Product, (iii) failure to follow RITE‑HITE's instructions for installation, failure
to operate the Product within the Product's rated capacities and/or specified design parameters, or failure to properly
maintain the Product, (iv) use of the Product in a manner that is inconsistent with RITE‑HITE's guidelines or local building
codes, (v) movement, settling, distortion, or collapse of the ground, or of improvements to which the Products are affixed,
(vi) fire, flood, earthquake, elements of nature or acts of God, riots, civil disorder, war, or any other cause beyond the
reasonable control of RITE‑HITE, (vii) improper handling, storage, abuse, or neglect of the Product by Owner or by any
third party.
LIMITATION OF LIABILITY IN NO EVENT SHALL RITE‑HITE BE RESPONSIBLE FOR, OR LIABLE TO ANYONE
FOR, SPECIAL, INDIRECT, COLLATERAL, PUNITIVE, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF
RITE‑HITE HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Such excluded damages include, but
are not limited to, personal injury, damage to property, loss of goodwill, loss of profits, loss of use, cost of cover with any
substitute product, interruption of business, or other similar indirect financial loss.
GLOBAL SALES & SERVICE Representatives in All Major Cities
RITE-HITE WORLD HEADQUARTERS
8900 N. Arbon Drive
P.O. Box 245020
Milwaukee, Wisconsin 53224
68
414-355-2600
U.S. Only: 1-800-456-0600
RITEHITE.COM
www.ritehite.com
RITE-HITE CHINA
First Floor, Building #3,
558 Tongxie Road,
Changning District
Shanghai 200335, China
+86-21-6237-6333
RITE-HITE LATIN AMERICA
Alameda Lorena, 800 - Conj. 401/402
- Jardim Paulista
São Paulo/SP, CEP 01424- Brazil
011-55-11-3527-9590
RITE-HITE GMBH
Carl-Zeiss-Strasse 3
34471 Volkmarsen, Germany
+49-5693 98700
Publication: AMEN00047 2017-03-06
170303
DISCLAIMERS THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER REPRESENTATIONS AND
WARRANTIES, EXPRESS OR IMPLIED, AND RITE‑HITE EXPRESSLY DISCLAIMS AND EXCLUDES ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR PURPOSE. RITE‑HITE SHALL NOT BE SUBJECT TO ANY
OTHER OBLIGATIONS OR LIABILITIES, WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT
(INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORIES OF LAW, WITH RESPECT TO THE
PRODUCTS SOLD OR SERVICES RENDERED BY RITE‑HITE, OR ANY UNDERTAKINGS, ACTS, OR OMISSIONS
RELATING THERETO.
">