Canon | iPF750 | Setup guide | Canon iPF750 Setup Guide

Introductory Information
ENG
Setup Guide
Caution
Read this manual before attempting to operate the printer.
Keep this manual in a handy location for future reference.
• Instructions in this Setup Guide show the iPF755 printer. Note that your printer may look different from these illustrations in some cases. However,
basic operations are the same.
Introduction
Overview of Setup
Space Required for Installation
These are the steps in printer installation.
Preparations
+300mm
+10mm =0mm?㧖
(P.2)
+200mm
Install the Ink Tanks
(P.3)
+600mm
Install the Printhead
+200mm
*Values enclosed in [ ] are for when the stand is attached.
(P.4)
Printer
iPF650/iPF655
Load Cut Sheet Paper
(P.5)
Install the Printer Driver and
the User Manual
(P.6)
iPF750/iPF755
Installation space (W x D x H mm)
Printer alone
1397 × 1308 × 807
With stand attached
1397 × 1470 × 1362
Printer and stand
1704 × 1470 × 1362
Package Contents
i
g
Store Accessories in the Pockets (P.15)
j
Details for each step are given in this Setup Guide. Simply follow the instructions
to install the printer.
If an error message is displayed during setup or other problems occur, refer to
"Responding to Messages".
c
k
h
d
e
f
Printer Documentation
a
b
After installing the printer as shown in this Setup Guide, refer to the
documentation for instructions on operation and maintenance.
Daily operation
The Basic Guide includes three booklets containing the following information:
1 Instructions on basic operation
2 Troubleshooting tips and maintenance procedures
3 Preparations for transferring the printer, and instructions for
reinstalling the printer driver
a.
b.
c.
d.
e.
f.
Detailed instructions
The User Manuals CD-ROM (User Manual) includes the following information:
• Printer operating instructions
• Printer driver instructions
• Printing instructions
• Maintenance procedures
• Instructions for network printing
• Troubleshooting tips
• Printer menu descriptions
• Printer driver function details
• Specifications, details on consumables
and optional accessories, and other
information
MEMO
Supported paper
The Paper Reference Guide provides information about paper.
You can access the User Manual and Paper Reference Guide as follows:
g.
h.
i.
j.
k.
Sample paper
Setup Guide (this document)
Set of printer documentation
Set of CD-ROMs
Power cord
• Some items are included with the printer but not described in this manual.
Keep these items in a safe place after setup because they are used in
various printing applications.
• For instructions on using items not described in this manual, refer to the
User Manual.
• A cable to connect the printer to a computer is not provided with the printer.
• Canon, the Canon logo, and imagePROGRAF are trademarks or registered trademarks of CANON
INC.
• Microsoft and Windows are trademarks of Microsoft Corporation, registered in the U.S. and other
countries.
• Macintosh is a trademark of Apple Inc., registered in the U.S. and other countries.
• All other trademarks or registered trademarks described in this Setup Guide are the property of
their respective owners.
• In Windows, double-click the iPFxxxx Support desktop icon.
(iPFxxxx represents the printer model.)
• In Mac OS X, click iPF Support, added to the Dock.
QT5-2309-V1
Printer
Roll holder: Already attached to printer
3-inch paper core attachment R
3-inch paper core attachment L
Printhead
Starter ink tanks:
Bk, MBk (x 2), C, M, Y
1
©CANON INC. 2009
Printed in JAPAN
Preparations
1
Prepare the printer for use by installing the printer and connecting the power cord.
Install the printer. You can use the
following two methods for installing the
printer.
• Stands may be standard or optional
MEMO depending upon your model and location.
iPF750/iPF755: Standard
iPF650/iPF655: Optional (equipped as
standard in some locations)
• Install with a stand
2
Remove the packing materials from the
top of the printer.
4
Remove the orange tape used to secure
the roll holder to the printer.
6
Plug the power cord into the power supply
connector on the right of the printer and
plug the other end into the outlet.
Assemble the stand and install the
printer referring to the Printer Stand
Setup Guide included with the stand.
After installation, proceed to step 4.
• Install without a stand on a table
Proceed to step 2.
3
Three people should hold the printer's carrying handles and place the printer on a table or
other flat location.
Caution
5
• The iPF750/iPF755 weighs approximately
52 kg and the iPF650/iPF655 approximately
43 kg by themselves. Moving the printer
requires at least three people. Be careful
to avoid back strain and other injuries.
• When moving the printer, firmly grasp the
carrying handles. Holding the printer at
other positions is dangerous, and may
cause injury and damage if the printer is
dropped.
Move the printer to the location where you
will use it.
Caution
• When moving the stand, lift the support rod
to the position (a) before closing the output
stacker and unlocking the 4 casters. Failure
to do so may lead to scratched flooring,
damage to the basket cloth, and injury.
• After you have moved the stand, be sure to
lock the 4 casters.
a
OFF
ON
2
Install the Ink Tanks
1
Load all six ink tanks.
2
Press the power button to turn on the
printer.
When the following screen appears, use
the ▲ and ▼ keys to select a language
and press OK.
Language
Data
Message
3
Select your local time zone and press OK.
Time Zone
㪈㪆㪉
English
ᣣᧄ⺆
Français
Italiano
Deutsch
Data
Message
Load
4
Instructions on ink tank installation
are shown on the display screen. As
instructed, grab the handle on the ink tank
cover to open it.
5
While pressing the stopper of the ink tank
lock lever inwards, open the ink tank lock
lever upwards.
6
FEED
Cut
㪈㪆㪌
0:London (GMT)
+1:Paris,Rome
+2:Athens,Cairo
+3:Moscow
+4:Eerevan,Baku
Power
Menu
Stop
Back
Navigate
Shake the ink tanks gently 1 to 2 times
before opening the pouch.
• Failure to shake ink tanks may result in
reduced print quality because ink ingredients
have settled on the bottom of the tank.
7
Open the pouch and remove the ink tank.
• Never touch the ink holes (a)
or metal contacts (b). Touching
these parts may cause stains,
damage the ink tank, and affect
print quality.
8
9
Close the ink tank lock lever until it clicks
into place. Make sure the ink lamp is lit in
red.
a
b
• Avoid dropping the ink tank after
removing it from the pouch.Otherwise,
ink may leak and cause stains.
• Do not remove and shake ink tanks that
have already been installed in the printer
because ink may leak out.
10
Insert the ink tank into the holder facing
as shown, with the ink holes down.
Repeat steps 5 to 9 to install all of the ink
tanks.
• If the ink tank does not fit in the holder,
make sure the color of the ink tank lock
lever matches the color of the ink tank, and
check the orientation of the ink tank.
11
Close the ink tank cover.
3
• If the ink lamp is not lit, repeat steps 5, 8,
and 9.
9
Install the Printhead
1
Next, install the printhead.
Open Upper Cover is shown on the
display screen. As instructed, open the top
cover.
• When installing the printhead, do not
move the carriage (a) from the position
shown in the figure.
If you move the carriage (a), a warning
noise sounds and the printhead cannot
be installed.
If you have moved the carriage (a),
close the top cover. The carriage (a)
moves to the position shown in the
figure.
a
2
Pull the printhead fixer lever forward all
the way to open it completely.
5
Remove the orange protective part (a).
To remove orange protective part (b),
push the grip (c) as you remove the part.
Instructions on printhead replacement are
shown on the display screen.
3
Lift the printhead fixer cover to open it
fully.
4
Hold the printhead by the grips (a) as you
remove it from the pouch.
b
a
c
a
a
• Never touch the parts covered by the
protective part. This may damage the
printhead and affect printing quality.
• The printhead contains ink, so be careful
not to spill it once the protective part is
removed.
• Do not reattach the protective part after
removing it. Dispose of these materials
according to local regulations.
6
Insert the printhead into the carriage (b)
with the ink holes (a) facing away from the
printer as shown in the figure. Carefully
push the printhead firmly into the carriage
(b), ensuring that the part covered by
the protective part does not touch the
carriage.
7
Pull the printhead fixer cover down toward
the front to lock the printhead in place.
a
b
9
Close the top cover.
4
8
Push the printhead fixer lever all the way
back.
Load Cut Sheet Paper
1
Select type of paper for printhead adj.
is shown on the display screen. Check
that Cut Sheet is selected and press OK.
Load paper for adjusting the printhead into the printer.
Follow these steps to load cut sheet paper into the printer. The sample paper provided is used in this example.
2
Slide the width guide (a) and align it
with the mark for the size of paper to be
loaded. In this example, align the width
guide with A2 to align it with the size of the
sample paper.
3
Prepare one sheet of paper.
Refer to the packaging for the paper to
check which side is the printable surface.
• Return unused paper to the pouch it
came in, and store it away from heat,
humidity and direct sunlight.
a
Instructions on loading cut sheets are
shown on the display screen.
4
Load paper with the printable surface
face up.
Insert the paper until its leading edge
touches a stop and you hear a tone.
5
Adjust the position of the width guide (a)
to the size of the paper to be loaded.
Make sure the width guide fits properly
against the edge of the paper to prevent it
from being tilted or wrinkled.
6
A message confirming paper advance is
shown on the display screen. Press OK.
9
When printhead adjustment ends, paper is
printed with an adjustment pattern and is
ejected.
While holding the paper, press the release
lever (a) backwards to remove the paper.
a
• Only one sheet can be loaded in the
printer. Do not load two or more sheets.
Doing so might cause a paper jam.
• Wrinkled or warped paper might cause
paper jams. Be sure to flatten the paper
out before loading it.
7
The screen for selecting the paper type is
shown on the display screen. Press ▲ or
▼ to select the type of paper loaded in the
printer.
Select Coated Paper and press OK.
Then from the menu that appears, select
Coated Paper and press OK.
8
MEMO
When paper advance ends, the system
is automatically filled with ink for the first
time and printhead adjustment is started.
It takes a total of about 20 minutes.
Make use of this time by referring to
"Install the Printer Driver and the User
Manual" on page 6 to install the printer
driver and the User Manual on your PC.
During printer installation, ink fills the system
between the ink tanks and printhead. In
addition, printheads are cleaned to keep the
printer in optimal condition. This may cause
the maintenance cartridge capacity indicator
to drop to about 80%, but this is not a problem
with the printer.
a
The paper is advanced.
10
Pull the release lever forward.
MEMO
Printer setup is now complete.
• For how to load roll paper, refer to the Basic
Guide (1), to the User Manual installed
at "Install the Printer Driver and the User
Manual", or to the instructions displayed by
the navigation function of the control panel.
Follow the procedure below to display the
navigation on how to load roll paper.
1.Press Navigate.
2.Use the ▲ and ▼ keys to select Load Roll
Paper and press OK.
3.Use the ▲ and ▼ keys to select View Op.
Guide and press OK.
The navigation starts.
5
Install the Printer Driver and the User Manual
Windows
MEMO
You can print from Windows via USB or TCP/IP (network) connections.
The installation procedure varies depending on how your printer is
connected. Install the printer driver and the User Manual as follows.
The following screen may be displayed during installation depending on
the security settings of your computer.
• Select Deactivate the block and click Next.
<Compatible Operating Systems>
Windows Vista, Windows Server 2008, Windows Server 2003,
Windows XP, Windows 2000
• Installation requires administrative rights (such as those of Administrator).
Be sure to log on using an account with administrative rights before
installation.
For USB connections
• Use a USB cable that conforms to the
Hi-Speed USB specification.
• Connect the USB cable to the printer
as instructed during installation of the
relevant printer driver. If you connect the
USB cable before installing the printer
driver, the printer driver may not be
installed correctly.
1
After making sure the printer is not
connected to the computer, turn the
computer on. Insert the provided User
Software CD-ROM for your operating
system in the CD-ROM drive.
2
MEMO
3
Confirm that the required installation
items are selected in the Installation List
window, and then click Next.
MEMO
6
4
In the Select Country or Region of Use
window, select the country or region of
use and click Next.
5
In the Setup Menu window, click Install
Printer Driver.
• To choose a different language, click
Language.
After reading the license agreement, click
Yes.
• Point at a software title to view a
summary of the software.
In the Printer Selection window, select
The printer is connected directly to a
computer and click Next.
7
In the Printer Installation dialog box,
select Install with USB Connection, and
click Next.
8
MEMO
6
When the following dialog box is
displayed, make sure the printer is on
and use the USB cable to connect the
printer to the computer.
• If a warning message is displayed, click
Retry to try again.
9
14
10
In the Finish window, select Restart my
computer now and click Restart.
13
Click Next.
16
After installation is completed, click Finish.
• Be careful not to insert the USB cable
into the Ethernet port.
MEMO
11
After reviewing the installation results in
the Complete Installation window, click
Next.
The printer driver settings take effect after
the computer restarts. This completes
printer driver installation.
An iPFxxxx Support desktop icon
is created after installation. (iPFxxxx
represents the printer model.)
Next, install the User Manual.
After reading the software license
agreement, select I accept the terms of
the license agreement, and then click
Next.
12
15
When the Install User Manual dialog
box is displayed, insert the provided User
Manuals CD-ROM in the CD-ROM drive
and click Next.
Click Install.
The installation process begins.
The User Manual is now installed.
For TCP/IP (network) connections
When you first connect the printer to the network
1
2
Use the LAN cable to connect the LAN
port on the back of the printer to the hub
port. Pass the network cable through the
wiring bracket (a).
MEMO
• If the printer is on, the Link indicator
under the LAN port lights.
1000Base-T
connection
100Base-TX
connection
10Base-T
connection
The LED on the bottom
lights green.
The LED on the top lights
orange.
The LED on the top lights
green.
a
7
Make sure the printer is on.
Turn the computer on and insert the
provided User Software CD-ROM for
your operating system in the CD-ROM
drive.
3
MEMO
In the Setup Menu window, click Install
Printer Driver.
4
Confirm that the required installation
items are selected in the Installation List
window, and then click Next.
9
10
In the Select Country or Region of Use
window, select the country or region of
use and click Next.
• To choose a different language, click
Language.
MEMO
6
5
After reading the license agreement, click
Yes.
Available printers are listed in the Search
Results window.
Select a printer from the list on either
their IPv4 Devices or IPv6 Devices tabs
and click Next.
In the Method of Configuring IP
Addresses window, enter the IP address
in Configure manually, under Method of
Configuring IP Addresses. Click Install
to start the installation process. Also enter
your preferred name for the printer in
Device Name and the installation location
in Printer Location under Information
About Printer to Configure, as desired.
The installation process begins.
7
MEMO
• Point at a software title to view a
summary of the software.
In the Printer Selection window, select
The printer is connected to computers
in a network and click Next.
8
After reading the precautions in the
Getting Ready window, select Find
available printers in the network and
click Next.
• The IPv6 Devices tab is displayed in Windows Vista and Windows Server 2008.
• If the printer you want to use is not displayed in the list on the IPv6 Devices tab, connect via IPv4
instead.
• If the printer you want to use is not displayed in the list of printers on the IPv4 Devices tab, refer to
"When the printer cannot be found on the network" on page 9 to setup and configure an IP address
for the printer.
• If you use a DHCP server for automatic assignment of the printer's IP address, printing
may no longer be possible after the printer is turned off and on. This is because a different
IP address has been assigned. When using DHCP server functions, consult your network
administrator and configure the settings in one of the following ways:
• Configure the setting for dynamic DNS updating
In RemoteUI, activate the setting Enable DNS Dynamic Update. (→"Configuring the Printer's
TCP/IP Network Settings", User Manual)
• Configure the setting for assignment of the same IP address each time the printer starts up
8
11
After reviewing the installation results in
the Complete Installation window, click
Next.
12
In the Finish window, select Restart my
computer now and click Restart.
13
The printer driver settings take effect after
the computer restarts. This completes
printer driver installation.
An iPFxxxx Support desktop icon
is created after installation. (iPFxxxx
represents the printer model.)
Next, follow steps 12-16 on page 7 to
install the User Manual.
When the printer cannot be found on the network
If your printer cannot be found when
connecting to the network for the first time,
setup an IP address for the printer and
then configure it on the printer.
1
On the tab selection screen of the control
panel, press the ◄ and ► keys to select
(Settings/Adjustments) and press
OK.
When ink fills the system for the first time,
after printhead adjustment is finished,
specify the IP address on the printer's
control panel.
No Paper Loaded
OK:Setting/Adj. Menu
Maint. cart.
Remaining Amount
㪈㪇㪇㩼
• When ink fills the system for the
first time, do not operate the
printer until printhead adjustment
is finished.
4
Enter the IP address. Navigate through the
following menus using the ▲ and ▼ keys
on the control panel.
1.Select IPv4 and press OK.
2.Select IPv4 Settings and press OK.
3.Select IP Address and press OK.
4.Enter the IP address.
7
In the Search Results window, select
Specify the IP address of available
printers in the network and click Next.
The IP Address Specification window
appears. Follow steps 8-11 on page
11-12 to finish installing the printer driver.
MEMO
How to enter IP addresses
1.Press the ◄ and ► keys to select a field
for inputting values.
2.Use the ▲ and ▼ keys to input values.
• Pressing ▲ increases the value by
one. However, 0 comes after 255.
• Pressing ▼ decreases the value by
one. However, 255 comes after 0.
• Holding down either the ▲ or ▼ keys
continually increases or decreases the
value.
3. Press OK once you have finished.
Next, follow steps 12-16 on page 7 to
install the User Manual.
• If the following screen appears, click Retry
MEMO and select Specify the IP address of
available printers in the network on the
next screen that appears.
9
2
Use the ▲ and ▼ keys to select Interface
Setup and press OK.
3
Use the ▲ and ▼ keys to select TCP/IP
and press OK.
5
Press Menu.
6
Press OK on the registration confirmation
message that appears.
The IP address is set on the printer.
Next, restart installation of the printer
driver.
If the printer is already connected to the network
• If the printer is already connected to
the network, confirm the IP address
assigned to the printer. Ask your network
administrator for further information.
MEMO
1
Make sure the printer is on.
Turn the computer on and insert the
provided User Software CD-ROM for your
operating system in the CD-ROM drive.
2
• If the printer is on, the Link indicator under
the LAN port lights.
1000Base-T
connection
100Base-TX
connection
10Base-T
connection
The LED on the bottom
lights green.
The LED on the top lights
orange.
The LED on the top lights
green.
MEMO
3
Confirm that the required installation
items are selected in the Installation List
window, and then click Next.
MEMO
6
In the Setup Menu window, click Install
Printer Driver.
4
In the Select Country or Region of Use
window, select the country or region of
use and click Next.
5
• To choose a different language, click
Language.
After reading the license agreement, click
Yes.
• Point at a software title to view a summary
of the software.
In the Printer Selection window, select
The printer is connected to computers
in a network and click Next.
• The IPv6 Devices tab is displayed in
MEMO Windows Vista and Windows Server 2008.
• Printers already connected to the network
are labeled Available in IP Address
Status.
• If the printer you want to use is not
displayed in the list of printers, select
Specify the IP address of available
printers in the network and click Next.
The IP Address Specification window
appears. Follow steps 8-11 on page 11-12
to finish installing the printer driver and the
User Manual.
7
9
After reading the precautions in the
Getting Ready window, select Find
available printers in the network and
click Next.
After reviewing the installation results in
the Complete Installation window, click
Next.
10
8
10
Available printers are listed in the Search
Results window.
Select a printer from the list on either
their IPv4 Devices or IPv6 Devices tabs
and click Next.
The installation process begins.
In the Finish window, select Restart my
computer now and click Restart.
11
The printer driver settings take effect after
the computer restarts. This completes
printer driver installation.
An iPFxxxx Support desktop icon
is created after installation. (iPFxxxx
represents the printer model.)
Next, follow steps 12-16 on page 7 to
install the User Manual.
When entering the printer's IP address manually
• If the printer is already connected to
the network, confirm the IP address
assigned to the printer. Ask your network
administrator for further information.
MEMO
1
Make sure the printer is on.
Turn the computer on and insert the
provided User Software CD-ROM for
your operating system in the CD-ROM
drive.
2
In the Setup Menu window, click Install
Printer Driver.
• If the printer is on, the Link indicator under
the LAN port lights.
1000Base-T
connection
100Base-TX
connection
10Base-T
connection
The LED on the bottom
lights green.
The LED on the top lights
orange.
The LED on the top lights
green.
MEMO
3
Confirm that the required installation
items are selected in the Installation List
window, and then click Next.
MEMO
6
4
In the Select Country or Region of Use
window, select the country or region of
use and click Next.
5
• To choose a different language, click
Language.
After reading the license agreement, click
Yes.
• Point at a software title to view a summary
of the software.
In the Printer Selection window, select
The printer is connected to computers
in a network and click Next.
7
After reading the precautions in the
Getting Ready window, select Specify
the IP address of available printers in
the network and click Next.
8
In the IP Address Specification window,
select either IPv4 Address or IPv6
Address to enter the printer's IP address
and click Install.
The installation process begins.
MEMO
• IPv6 Address is displayed in Windows
Vista and Windows Server 2008.
• Ask your network administrator for the
IP address, as needed.
11
9
After reviewing the installation results in
the Complete Installation window, click
Next.
10
In the Finish window, select Restart my
computer now and click Restart.
11
The printer driver settings take effect after
the computer restarts. This completes
printer driver installation.
An iPFxxxx Support desktop icon
is created after installation. (iPFxxxx
represents the printer model.)
Next, follow steps 12-16 on page 7 to
install the User Manual.
12
Macintosh
You can print from Macintosh via USB or network connections such as
Bonjour or IP.
Install the printer driver that suits your printing environment.
<Compatible Operating Systems>
Mac OS X 10.3.9 or later
Connect the printer to a computer
Connect the cable
1
Use a cable to connect the printer to a computer or the network. When connecting to a
network, pass the network cable through the wiring bracket (a).
• For USB connections
2
Make sure the printer is on.
Turn the computer on.
• For network connections
a
MEMO
• Be careful not to insert the USB cable into the Ethernet port.
Configure the computer
Install the printer driver
• Be sure to log in as a user with
administrative rights when installing the
printer driver.
1
Insert the provided User Software
CD-ROM for your operating system in the
CD-ROM drive.
2
On the desktop, double-click the CD-ROM
icon and then the iPF Printer Setup icon.
User Software
3
6
If the following screen is displayed, enter
the user name and password of a user
with administrative rights and click OK.
Click Next.
4
Confirm that the required installation items
are selected, and then click Next.
5
Select the country or region where the
printer will be used and click Next.
7
After reading the software license
agreement, click Continue.
8
Click Agree.
13
9
Click Continue.
12
Click Quit.
14
Select the printer to setup and
click Next.
10
Exit other applications and click Continue.
The printer driver, additional printer driver
features, ICC Profiles, and the Media
Configuration Tool are now installed.
This completes printer driver installation.
Next, select the printer to set up.
13
15
16
After entering your preferred name for the
printer in Printer Name and the installation
location in Location, click Register.
• To register the printer by entering its IP
address, click Registering IP Address.
Enter the IP address of the desired
printer in IP Address and click Next.
MEMO
11
MEMO
Click OK.
Click Next.
Click Finish.
• To register another printer, click Continue
Registration, and repeat steps 14 to 16.
Install the User Manual
17
Click OK.
MEMO
20
18
The following screen is displayed and
paper information is updated. When the
paper information has been updated, the
screen is no longer displayed.
19
Next, install the User Manual.
Insert the provided User Manuals
CD-ROM in the CD-ROM drive.
• If the same model of printer is already
registered on the computer, a screen is
displayed for printer selection. Select
the desired printer and click Next.
Double-click the iPFxxxx Manual
Installer icon on the CD-ROM. (iPFxxxx
represents the printer model.)
21
Select the region where the printer will
be used and the language of the user
manual to install, and then click OK.
14
22
Check the message and click Continue.
23
After reading the software license
agreement, click Continue.
26
After installation is completed, click Quit.
24
Click Agree.
25
Click Install.
2
When using the stand, store the 3-inch
paper core attachment and other
accessories in the accessory pocket.
The User Manual is now installed.
Store Accessories in the Pockets
1
Use the manual pocket to store the Basic Guide (which includes descriptions of basic printer
operations, routine maintenance, and troubleshooting tips), so you can refer to it as needed.
MEMO
15
• The accessory pocket is included with
the stand.
Responding to Messages
Error messages may appear on the display screen of the control panel during printer installation in some cases. If so, it may not indicate a problem with the
printer, and the issue may be easily resolved. Common messages and the causes are listed here with corrective actions. To respond to error messages other
than these, refer to the Basic Guide (2). For other detailed printer instructions, refer to the User Manual installed at "Install the Printer Driver and the User
Manual".
Message
Cause
Corrective Action
No ink tank loaded.
Check ink tank.
There is no ink tank of the indicated color in
the printer.
Load or reload the ink tank.
(see steps 4-11 on page 3)
No printhead
Install printhead.
The printhead is not installed.
Install the printhead.
(see steps 1-9 on page 4)
Paper is crooked.
Push the release lever back, then
Pull out the cut sheet.
The loaded paper is crooked.
Could not detect paper size. Push release
lever back,
Pull out the cut sheet.
The paper is loaded in the wrong position or
the paper is curled.
1.
2.
3.
4.
Insert the maintenance cartridge.
The maintenance cartridge is not installed.
Install the maintenance cartridge.
Hardware error.
xxxxxxxx-xxxx
(x represents a letter or number)
Another kind of error has occurred.
Turn off the printer and wait at least three seconds before restoring
the power. If the message still appears, write down the error code and
message, turn off the printer, and contact your Canon dealer for assistance.
ERROR Exxx-xxxx
(x represents a letter or number)
You may have encountered an error that
cannot be resolved.
Write down the error code and message, turn off the printer, and contact
your Canon dealer for assistance.
16
Press the release lever backwards.
Pull out the paper.
Pull the release lever forward.
Load or reload the paper.
Download PDF

advertising