Canon | S630 | Instruction Guide | Canon S630 Instruction Guide

Start Here
Color Bubble Jet™ Printer
Easy Setup Instructions
1 Unpack the Printer
2 Prepare the Printer
1 Carefully remove all items from the box.
3 Install the Printhead
1 Remove the shipping tape from the front
and sides of the printer.
1 Remove the printhead from its package.
4 Install the Ink Tanks
1 Pull the orange tab off the yellow ink tank
(BCI-3eY), then remove and discard the
plastic wrapper.
5
Connect the Printer
To Your Computer
For USB Cables:
1 Turn the printer off.
IMPORTANT: Be sure printer is off
before continuing, or the computer
will attempt to install the printer
driver before the printer is ready.
2 Connect one end of the USB cable
to the computer, the other to the printer.
Shipping tape
2 Turn the printhead over, then remove
the orange protective cap.
2 Twist off and discard the orange
protective cap.
S630 Series
Color Bubble Jet Printer
Protective cap
2 Plug the power cord into the back of the
printer and connect the other end to a
power outlet.
USB port
NOTE: Do not touch the electrical contacts.
Paper rest
Output tray
NOTE: To avoid spilling ink, never press on
the sides of an ink tank.
Electrical contacts
3 Insert the ink tank into the correct slot.
(Refer to the color guide on the printhead.)
USB cable
Press down gently until the ink tank locks
into place.
USB port
For Parallel Cables:
3 Press the POWER button to turn the
printer ON.
POWER
button
3 Raise the gray lock lever.
1 Turn the printer off.
POWER
lamp
IMPORTANT: Be sure printer is off
before continuing, or the computer
will attempt to install the printer
driver before the printer is ready.
4 Insert the remaining three ink tanks into
their assigned slots.
Documentation
and software kit
2 Connect one end of the parallel cable to
the computer, the other to the printer.
(IEEE 1284 compliant)
4 Open the front cover. The printhead holder
automatically moves to the center. Remove
the protective tape.
4 Slide the printhead into the holder. The
printhead will rest at a slight angle.
Do not press it down.
Parallel cable
S630 BJ (Bubble Jet) Printhead
Power cord
5 Close the front cover and attach the
paper rest and output tray.
5 Lower the lock lever and press it down
until it locks firmly into place.
Secure
wire clips
Protective tape
Parallel cable
Ink tanks
BCI-3eC Cyan
BCI-3eM Magenta
BCI-3eBK Black
BCI-3eY Yellow
Serial number
5 Write down the serial number located to
the right of the printhead. You will need
this later to register the product.
Parallel port
Continue with Step 6
on side two.
7 Align the Printhead
6 Install the Printer Driver (Macintosh )
6 Install the Printer Driver (Windows )
®
W
in
do
ws
M
ac
in
to
sh
®
1 Be sure the printer is OFF before continuing.
POWER
button
POWER
lamp off
6 Click Start. (If the Printer Driver button is
not red, select Printer Driver, then click
Start.) The printer driver will start loading
automatically.
1 Insert the S630 Setup Software & User's
Guide CD-ROM.
7 After the computer restarts, TURN THE
PRINTER ON. Select the Apple menu,
then Chooser.
NOTE: Screen shots may differ depending on
the operating system used.
1 Load a stack of blank paper in the
paper rest.
22
2 Open the printer driver folder on the CD-ROM,
then double-click the Installer icon.
Start the alignment procedure.
Windows:
a. Click Start, then Settings, then
Printers.
NOTE: For Windows 2000 or Windows NT 4.0,
log on to Windows as an Administrator before
continuing.
IMPORTANT: If you see this screen,
click Cancel and continue.
Before using the printer, align the printhead
to ensure the best quality printing.
7 TURN THE PRINTER ON so the printer port
(connection) can be automatically detected.
POWER
button
b. Right-click the Canon S630 icon,
then click Properties.
8 Click the S630 icon in the Chooser. The
printer name will highlight and move to
the right panel.
c. Click the Maintenance tab, then
click the Print Head Alignment icon.
POWER
lamp on
d. When asked to start printhead
alignment, click OK.
3 Read the License Agreement, then click Accept.
2 Close any open software applications,
then insert the S630 Setup Software &
User's Guide CD-ROM. The setup program
should run automatically.
NOTE: If the setup program does not run,
click Start, then Run, then type D:\msetup.exe,
where D is your CD-ROM drive.
The software will begin identifying the
printer port being used.
4 Click Install. The printer driver will load
automatically.
IMPORTANT: If your computer cannot
detect a printer port, refer to the
Troubleshooting chapter in the
S630 Quick Start Guide for instructions.
e. Follow the on-screen instructions
to complete printhead alignment.
NOTE: To use the BJ Print Monitor, click the
Backgrounding button to the On position.
Macintosh:
9 Close the Chooser.
a. From the File menu in a software
application, click Page Setup.
10 To ensure highest quality output, continue
with step 7 Align the Printhead.
3 Read the Welcome screen, then click Next.
8 When the Terminate Installation window
appears, click OK.
5 If the message "No other applications can
be running..." displays, click Continue.
4 Read the License Agreement, then
click Yes.
5 When the main menu appears, click
Install Software.
9 If you are prompted to restart the computer,
click Yes. When the installation and
registration process has completed, click Exit.
NOTE: You can now install the BJ Solution
software. Insert the BJ Solution CD-ROM.
The setup program should start automatically.
Follow the on-screen instructions.
c. Click the down-arrow to select
Test Print.
NOTE: You can now install the BJ Solution
software. Insert the BJ Solution CD-ROM.
The setup program should start automatically.
Follow the on-screen instructions.
d. Click the Print Head Alignment icon.
6 When the "Installation was successful"
screen displays, Restart your computer.
NOTE: Remember to register your product to
ensure product support. The serial number is
located on the inside of the printer, to the
right of the printhead.
10 To ensure highest quality output, continue
with step 7 Align the Printhead.
b. Click the Utilities button.
e. Follow the on-screen instructions
to complete printhead alignment.
3
3
Click OK (Windows) or Close (Macintosh)
when finished.
NOTE: Register your product to ensure product
support. Open the printer driver folder and doubleclick the Product Registration icon, then follow
the on-screen instructions.
The serial number is located on the inside of the
printer, to the right of the printhead.
NOTE: If you are prompted to restart Windows,
remove the CD-ROM, then click OK. After the
computer restarts, insert the CD-ROM and continue.
Part no. 0010X610/QA-1729
© 2001 Canon U.S.A., Inc.
Canon, BJ, BCI and Bubble Jet are trademarks of Canon Inc.
All other products and brand names are registered
trademarks or trademarks of their respective owners.
Specifications subject to change without notice.
PRINTED IN U.S.A.
PRINTED IN THAILAND
Download PDF

advertising