MSTRONIC MSE PSE-SW5G User manual

Add to my manuals
17 Pages

advertisement

MSTRONIC MSE PSE-SW5G User manual | Manualzz

PSE-SW5G

5 Port PoE Switch & Extender

(Repeat Ethernet and PoE)

USER’S MANUAL

MSTRONIC CO., LTD.

User’s Manual PSE-SW5G series

1. General Information..............................................................

3

2. Hardware Description...........................................................

LED Indicators.......................................................................................

Power Wiring ........................................................................................

Ethernet Port Wiring..............................................................................

PD Port Wiring......................................................................................

Network Application……………………………………............................

3

3

6

9

11

12

3. Model Information...........................................................

12

4. Technical Specification........................................................

13

MSTRONIC CO., LTD.

2

User’s Manual PSE-SW5G series

1. General Information

The PSE-SW5G PoE (Power Over Ethernet) Switch family provides four 10M/100M/1000M TX ports with PoE PSE function plus one 10M/100M/1000M TX up-link port with PoE PD function. It accepts power from PoE power souring equipment (PSE) and delivers power to PoE powered device (PD), which are compliant with IEEE802.3af and IEEE802.3at standard to receive and deliver both Ethernet data and DC power through the traditional UTP or STP cable. The PoE

Switch can extend Ethernet data and DC power up to 200 meters.

This manual will help you to install and maintain the PoE switch. Installation of the PoE switch is very easy and you can start to use the product as soon as it has powered up.

2. Hardware Description

*LED Indicator

There are 12 LEDs on the PoE switch to indicate the status of power and signal. The following section describes the functions of each LED indicator.

Front panel detail

MSTRONIC CO., LTD.

3

User’s Manual PSE-SW5G series

*POWER LED

LED

Power

STATUS

Green

Red

Description

LED ON when power input (DC IN on rear panel or UPLINK on front panel) has valid power supplied.

The indicator is used on full range voltage model(PSE-SW5G-11x1) and

12VDC typical model(PSE-SW5G52x0),

LED ON when the following warning condition happens.

*Power input under voltage (Vin<10V)

*Power input over voltage (Vin>59V)

*PoE over current (2A/per port) the indicator is unused on 24V typical model(PSE-SW5G-25x4),48V typical model(PSE-SW5G44x4) and 4 individual input

(P/N:PSE-SW5G11XN).

.

Off

*SWITCH LED (the right indicator on RJ45)

No power supplied.

LED

P1~P5

Link/Act

STATUS

Green

Green

Blinking

Yellow

Description

A network device is detected (1000Mbps), but no communication activity is detected.

This port is transmitting to, or receiving package from another device at 1000Mbps.

A network device is detected (10Mbps or

100Mbps), but no communication activity is detected.

MSTRONIC CO., LTD.

4

User’s Manual PSE-SW5G series

Yellow

Blinking

This port is transmitting to, or receiving package from another device at 10Mbps or

100Mbps.

Off No device is detected.

*PoE LED (the left indicator on RJ45)

Yellow P1~P4

PoE

Off

A valid Powered Device (PD) is detected and delivering power on this port.

No PD is detected on this port.

UPLINK (P5)

PoE 24V typical model(PSE-SW5G25x4) &

48V typical model(PSE-SW5G44x4):

Powered via all 4 data pairs.

Full range voltage model

(PSE-SW5G11x1), &4 individual input

(P/N:PSE-SW5G11XN): (2 data pairs or 4 data pairs)

Yellow

Blanking

24V typical model(PSE-SW5G25x4) &

48V typical model(PSE-SW5G44x4):

Powered via 2 data pairs. (1,2,3,6 or 4,5,7,8 are all acceptable).

Full range voltage model

(PSE-SW5G11x1), & 4 individual input

(P/N:PSE-SW5G11XN):unused.

Off No power is detected on this port.

MSTRONIC CO., LTD.

5

User’s Manual PSE-SW5G series

*Power wiring

The PoE switch family includes 5 models, be used for 5 different ranges of input voltage: full range voltage (12 to 57VDC) (P/N: PSE-SW5G1111,PSE-SW5G1141,PSE-SW5G1181)

12VDC typical (10 to 15VDC) (P/N: PSE-SW5G5210,PSE-SW5G5240,PSE-SW5G5280)

24VDC typical (12 to 36VDC) (P/N: PSE-SW5G25A4,PSE-SW5G25B4,PSE-SW5G25D4)

48VDC typical (44 to 57VDC) (P/N: PSE-SW5G44A4,PSE-SW5G44B4,PSE-SW5G44D4)

4 individual inputs (12 to 57VDC) (P/N:PSE-SW5G11XN)

The PoE switch family allows for it to be powered by another PoE source on port 5 (UPLINK) as a

PoE repeater or extender. For PSE-SW5G25x4 and PSE-SW5G44x4 are 44~57VDC, for full range voltage model(PSE-SW5G11x1), and 4 individual input model(PSE-SW5G11XN) are

12~57VDC. The 12VDC typical model(PSE-SW5G52x0) without PoE input function.

For PoE operation, make sure your power supply can offer at least 75W for 4x 802.3af PoE port, or

150W for 4x 802.3at PoE port.

If powered via the rear terminal, please make sure the input current is not over 10A. total output 8A maximum.

If powered on port 5, the input current is not over 2Amp. Total output 2A maximum.

Ports 1~4 will deliver DC power over the Ethernet cable as detailed below:

Mode A:

* Data pair A plus V+ on line 1 and 2

* Data pair B plus V- on line 3 and 6

* Data pair C on line 4 and 5

* Data pair D on line 7 and 8

Mode B:

* Data pair A on line 1 and 2

* Data pair B on line 3 and 6

* Data pair C plus V+ on line 4 and 5

* Data pair D plus V- on line 7 and 8

MSTRONIC CO., LTD.

6

User’s Manual PSE-SW5G series

Mode D (dual,=A+B):

* Data pair A plus V+ on line 1 and 2

* Data pair B plus V- on line 3 and 6

* Data pair C plus V+ on line 4 and 5

* Data pair D plus V- on line 7 and 8

Port 5 may receive DC power over the Ethernet cable, as detailed below:

* Data pair A plus V+ /V- on line 1 and 2

* Data pair B plus V-/V+ on line 3 and 6

* Data pair C plus V+/V- on line 4 and 5

* Data pair D plus V-/V+ on line 7 and 8

The terminal block on the rear panel should be wired as detailed below:

The DIN-4P connector on the rear panel also used for power input, you can use an AC/DC adapter with DIN-4P connector directly, recommends adaptor products as detailed below: (OPTION)

MS-180-18 MS-180-24 MS-180-48 MS-180-56

Maximum output 18VDC/8.35A 24VDC/6.25A 48VDC/3.75A 56VDC/3.2A

Related model

PSE-SW5G1111

PSE-SW5G1141

PSE-SW5G1181

PSE-SW5G25A4

PSE-SW5G25B4

PSE-SW5G25D4

PSE-SW5G11XN

PSE-SW5G1111

PSE-SW5G1141

PSE-SW5G1181

PSE-SW5G25A4

PSE-SW5G25B4

PSE-SW5G25D4

PSE-SW5G11XN

PSE-SW5G1111

PSE-SW5G1141

PSE-SW5G1181

PSE-SW5G44A4

PSE-SW5G44B4

PSE-SW5G44D4

PSE-SW5G11XN

PSE-SW5G1111

PSE-SW5G1141

PSE-SW5G1181

PSE-SW5G44A4

PSE-SW5G44B4

PSE-SW5G44D4

PSE-SW5G11XN

MSTRONIC CO., LTD.

7

User’s Manual PSE-SW5G series

*For 24VDC typical model(PSE-SW5G25x4)

Please note that the maximum power per port of 35W can only be achieved using 24VDC input operation. If your input is 12VDC, then the total power per port should be de-rated to 17W per port.

Total output of 24VDC typical model is 35W(802.3at) x2 or 17W (802.3af) x 4.

*For 48VDC typical model(PSE-SW5G44x4) (PSE-SW5Gxxx4)

The input voltage must be in the range of 44 to 57VDC if running for 802.3af operation.

The input voltage must be in the range of 50 to 57VDC if running for 802.3at operation.

If the 48VDC typical model is not powered with the above designated input voltage, it will only function as an Ethernet switch without PoE output.

Model

Input Voltage

(REAR)

Input Voltage

(Port 5)

Output voltage 802.3af/at Isolated

PSE-SW5G1111

PSE-SW5G1141

PSE-SW5G1181

12-57VDC

No input

12-57VDC

No input

12-57VDC

12-57VDC

12-57VDC

(As input voltage)

(non-regulated)

12-57VDC

(non-regulated)

Higher voltage output

(REAR or Port 5)

No

No

No

No

No

No

PSE-SW5G25A4

PSE-SW5G25B4

PSE-SW5G25D4

12-36VDC

No input

12-36VDC

No input

44-57VDC

44-57VDC

56VDC

(regulated)

44-57VDC

(non-regulated)

56VDC

(regulated)

Yes

Yes

Yes

No

No

No

PSE-SW5G44A4

PSE-SW5G44B4

PSE-SW5G44D4

44-57VDC

No input

44-57VDC

No input

44-57VDC

44-57VDC

44-57VDC

(non-regulated)

44-57VDC

(non-regulated)

Higher voltage output

(REAR or Port5)

Yes

Yes

Yes

No

No

No

MSTRONIC CO., LTD.

8

User’s Manual PSE-SW5G series

PSE-SW5G5210

PSE-SW5G5240

PSE-SW5G5280

10-15VDC No input

24VDC

(regulated)

No No

PSE-SW5G11XN

12-57VDC

No input

12-57VDC

No input

12-57VDC

12-57VDC

12-57VDC

(As input voltage)

(non-regulated)

12-57VDC

(non-regulated)

Higher voltage output

(REAR or Port 5)

No

No

No

No

No

No

*Ethernet Port Wiring

The PoE switch family supports one RJ-45 uplink (port 5 with PoE PD) and four RJ-45 ports (port

1~4 with PoE PSE) with automatic MDI/MDI-X crossover, auto-sense for speed and duplex for

10Base-T, 100Base-TX or 1000Base-T connection. Automatic MDI/MDI-X crossover allows you to connect to other devices (switches, hubs, or workstations etc.), without regard to using straight-through or crossover cabling.

Port 1 to 4 provides Power over Ethernet function that delivers DC power through the data pairs C

& D (pin 4,5 and pin 7,8) (mode B) to the PD. Port 5 provides Power Device function that receive power from 4 pairs or 2 pairs Ethernet cable.

The following tables describe the wiring diagram of straight-through and crossover cabling. The crossover cables simply cross-connect the transmit lines at each end to the receive lines at the opposite end.

MSTRONIC CO., LTD.

9

User’s Manual PSE-SW5G series

Straight-through Cabling

Pin 1 Pin 1

Pin 2

Pin 3

Pin 6

Pin 4

Pin 5

Pin 7

Pin 8

Pin 2

Pin 3

Pin 6

Pin 4

Pin 5

Pin 7

Pin 8

Pin 1

Cross-over Cabling

Pin 3

Pin 2

Pin 3

Pin 6

Pin 1

Pin 6

Pin 4

Pin 5

Pin 2

Pin 7

Pin 8

Pin 7 Pin 4

Pin 8 Pin 5

Connect an Ethernet cable into any switch port and connect the other side to your attached device. The Link/Act LED (green or yellow) will light up when the cable is correctly connected. Refer to the LED Indicator section for descriptions of each LED indicator.

If a port LED is off, go back and check for connectivity problems between that port and the network device connected.

The maximum cable length for 10/100/1000BaseT with Cat 5 twisted pair cables is typically 100m

(328 ft.).

MSTRONIC CO., LTD.

10

User’s Manual PSE-SW5G series

*PD Port Wiring

Port 1 to 4 provides PoE injection function with maximum 35W ability to power up the powered device using the straight-through or cross-over Ethernet cable.

The PoE switch follows the IEEE802.3af Alternative B mode connector assignment. The following table shows pin assignment of alternative A and B for the Power Source Equipment.

Conductor

1

2

3

4

5

6

Alternative A

(MDI-X)

Negative Vport

Negative Vport

Positive Vport

Positive Vport

Alternative A

(MDI)

Positive Vport

Positive Vport

Negative port

NegativeVport

Alternative B

(All)

Positive Vport

Positive Vport

7

8

Negative Vport

Negative Vport

Be sure the twisted pair cable is bound with the standard RJ-45 pin, especially the pins 4, 5, 7 and 8.

If the RJ-45 is bound with the wrong pin number, the PoE switch will not recognize the PD and won’t deliver DC power to the PD. The yellow PoE LED will light up when the cable is correctly connected. Refer to the LED Indicator section for descriptions of each LED indicator. If a port

LED is off, go back and check for connectivity problems between that port and the network device connected.

*Network Application

The PoE Switch can receive power from a PoE midspan and provide power to the PD which follows the IEEE 802.3af/at standard in the network. The PoE Switch can be installed in a more appropriate position for better performance to extend Ethernet to 200 meters. The following figure is an example of a network application for the PoE Switch.

MSTRONIC CO., LTD.

11

User’s Manual PSE-SW5G series

MSTRONIC CO., LTD.

12

User’s Manual PSE-SW5G series

3. Model Information

Model number

PSE-SW5G1111

PSE-SW5G1141

PSE-SW5G1181

PSE-SW5G25A4

PSE-SW5G25B4

PSE-SW5G25D4

PSE-SW5G44A4

PSE-SW5G44B4

PSE-SW5G44D4

PSE-SW5G5210

PSE-SW5G5240

PSE-SW5G5280

PSE-SW5G11XN

Input Voltage

12~57VDC(P3)

12~57VDC(POE)

12~57VDC(P3)

12~57VDC(POE)

12~57VDC(P3)

12~57VDC(POE)

12-36VDC(P3)

44~57VDC(POE)

12-36VDC(P3)

44~57VDC(POE)

12-36VDC(P3)

44~57VDC(POE)

44-57VDC(P3)

44~57VDC(POE)

44-57VDC(P3)

44~57VDC(POE)

44-57VDC(P3)

44~57VDC(POE)

10~15VDC

10~15VDC

10~15VDC

Vout/pin out/Iout

Vi/1236/2A

Vi/4578/2A

Vi/1236+4578/2A

56VDC/1236/0.625A

56VDC/4578/0.625A

56VDC/1236+4578/0.625A

Vi/1236/0.625A

Vi/4578/0.625A

Vi/1236+4578/0.625A

24V/1236/0.84A

24V/4578/0.84A

24V/1236+4578/0.84A

Output Wattage

2A/port

2A/port

2A/port

35W/port

35W/port

35W/port

35W/port

35W/port

35W/port

20W/port

20W/port

20W/port

12~57VDC Vi/4578/2A 2A/port

Remark

802.3at

802.3at

802.3at

802.3at

802.3at

802.3at

4 individual input

MSTRONIC CO., LTD.

13

User’s Manual PSE-SW5G series

4. Technical Specifications

Standards IEEE802.3/IEEE802.3u standards/IEEE802.3ab (10 base-T/100base-TX/1000base-T)

Ports 5 ports with PoE (4 PSE & 1 PD), support auto-crossover &

auto-polarity

Transmission speed 1000Mbps (1000base-T).100 Mbps (100base-TX), 10 Mbps(10base-T)

Auto-negotiation

Switch technology store-and-forward

Protocols CSMA/CD

Flow control IEEE802.3x (full-duplex), back pressure (half-duplex)

Data transmission rate 1488000pps for1000base-T, 148800pps for 100base-T, 14880pps for

10base-T

Address table 2K MAC address table, self-learning

Connect RJ-45

PoE port Port 1-4, PSE auto power management

Pin assignment:

*A mode: data pair A plusV+(1,2), data pair B plusV-(3,6), data pair C (4,5), data pair D (7,8)

*B mode: data pair A (1,2), data pair B (3,6), data pair C plusV+(4,5), data pair D plus V-(7,8)

MSTRONIC CO., LTD.

14

User’s Manual PSE-SW5G series

*A+B mode: data pair A plusV+(1,2), data pair B plusV-(3,6), data pair C plusV+(4,5), data pair D plus V-(7,8)

Port 5, 4 pairs PD

Maximum PoE power Port 1-4: IEEE802.3af – 16.8W

IEEE802.3at – 35W

Current limited – 2A

24V output – 20W

(Total power for PSE-SW5G25x4 – 70W)

Port 5: 90W (802.3at 2 event classification)

Current limited – 2A

PSE disconnect mode DC disconnect

PoE auto detection IEEE802.3af & IEEE802.3at (2 event classification signaling)

PoE protection Over-temperature, over-current, over/under voltage

LEDs *Link/Activity (Green ON/ Green Blinking @1000Mbps,

Yellow/Yellow Blinking @10M/100Mbps)

*PoE (Yellow) port 1-4 ON - PD detect

Port 5 PSE-SW5G25x4 & PSE-SW5G44x4

ON – 4 pair power, Blinking-2 pair power

PSE-SW5G11x1,PSE-SW5G52x0 &

PSE-SW5G11XN ON – 2 or 4 pair power

*POWER Green-normal, Red-alarm

Power input Port 5 (UPLINK) from network switch or midspan, or optional DC power supply.

(see detail on page 8)

MSTRONIC CO., LTD.

15

User’s Manual PSE-SW5G series

Power consumption less than 5W when without PD loading

Input PSE-SW5G11x1 PSE-SW5G25x4 PSE-SW5G44x4

12V

24V

0.190A

0.104A

0.340A

0.170A

0.190A

0.104A

48V

56V

0.061A

0.056A

---

---

Power efficiency 85% at full load (@48V typical)

Operating temperature

-20 ℃~ +75℃

Operation humidity 90% relative humidity, non-condensing

Storage temperature

-40

℃~+85℃

Dimension 40mm(H)x118mm(W)x150mm(D) DIN RAIL Mountable

0.061A

0.056A

Surge Protection on data pairs

Signal

Operating Voltage

Clamping Voltage

Peak Pulse Current

Pin Protected

Data 5V

Data 16.5V (@I PP =5A, t p =8/20μs, I/O pin to GND)

20A (tp=8/20μs)

All 8 pin protected

Max. Shut Capacitance

<3pF (VR = 0V, f = 1MHz, I/O pin to GND)

< 1.5 pF (VR = 0V, f = 1MHz, Between I/O pins)

IEC COMPATIBILITY (EN61000-4)

IEC61000-4-2 (ESD) ±15kV (air), ±8kV (contact)

IEC61000-4-4 (EFT) 40A (5/50ns)

IEC61000-4-5 (Lightning) 20A (8/20μs)

NOTICE:

The product is not comply to LPS requirement, it need to evaluate at final system.

MSTRONIC CO., LTD.

16

User’s Manual PSE-SW5G series

MSTRONIC CO., LTD.

17

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement