Casablanca Fan Company Inteli-Touch 3 PN User's Manual

Casablanca Fan Company Inteli-Touch 3 PN User's Manual
CONTENTS
INTRODUCTION
MOUNTING RECOMMENDATIONS
FAN INSTALLATION CONTROL FEATURES:
INTELI•TOUCH 3 OPERATION INTELI•TOUCH 3 TROUBLESHOOTING
1
2
3
8
16
READ AND SAVE THESE INSTRUCTIONS
SAFETY FIRST
Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product and
proper installation; therefore, before attempting to install and operate your Casablanca fan, read this owner’s
manual completely and carefully. Retain this manual for future reference.
CAUTION:To avoid possible electrical shock, make certain that electricity is turned off at the
circuit breaker or fuse box before attempting any installation procedure.
BEFORE YOU START
• CAUTION: RISK OF ELECTRICAL SHOCK! All wiring must be performed in accordance with national and local electrical codes. If
you are unfamiliar with the wiring codes, you should use a qualified electrician. To avoid overheating and possible damage to other
equipment, do not install control to a receptacle, fluorescent light fixture, motor operated appliance, or transformer-supplied appliance..
• This fan is designed to be installed on an existing electrical outlet box. The outlet box must be UL Listed for ceiling fan installations, if
it is not, a new box must be installed. Casablanca extension poles are available for sloped or high ceiling installations.
• This ceiling fan requires a grounded electrical supply of 120 VAC, 60 Hz and a minimum 15 amp circuit.The maximum current requirement for the fan with light fixture is 3.8 amps.The fan uses about 1 amp or 100 watts. Maximum light current is
amps or
watts
of lighting.
• Where wire nuts are employed, be sure all bare wires are within the connectors.When installing the canopy hatch, make sure all wires
are within the canopy and that no wires are being pinched.
For best performance and for your warranty to be valid, use only genuine
Casablanca blades, light fixtures, and accessories.
SAFE USE
• The blades in each pack are matched for equal
FUSE BOX
weight to assure smooth fan operation. If more (Remove fuse for the
circuit you will be
than one fan is being installed, be careful not to
working on)
mix blades from different cartons.
• Inspect the contents of your carton for possible
shipping or handling damage and report any such
damage directly to your authorized Casablanca
dealer.
• It is always a good idea to have an assistant to help
with the installation.
• When cleaning, painting, or working near your fan,
be very careful of the fan and blades. Always turn CIRCUIT BREAKER
the power OFF to the ceiling fan before servicing (Trip breaker for the
it, working on it, or replacing light bulbs.
circuit you will be
• Never insert anything into the path of the fan blades
working on)
while the fan is in operation.
• Never install a fan over a pool or spa.
• Never operate a fan that has been damaged in any
way. Contact Casablanca Fan Company by calling
1-888-227-2178, or contact your local authorized
Casablanca dealer for assistance in obtaining
service.
PN 3843Z
HN0909
18”
70”
84”
1
MOUNTING RECOMMENDATIONS
Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation,
and fan size are all important factors to consider before installation.
Location
Ceiling fans have practical uses in almost every room in your home. We suggest you follow these mounting recommendations as you decide where to install your Casablanca fan.
• For safety reasons, the fan blades must be a minimum of 7” above the floor.
• Do not locate the fan in a doorway or above a swinging door.
• In any installation, the tips of the blades must be at least 18” from the wall in order to provide sufficient clearance
for the blades.
• In bedrooms, fans work best when mounted above the foot of the bed.
• Over pool tables, be sure to provide plenty of clearance to avoid damage
from pool cues.
• In kitchens be sure to allow for open cupboard doors to clear the fan blades.
• Do not install a fan close to, or over, a pool or spa. High humidity combined
with corrosive gases will destroy the finish and warp the blades.
Fan Size
Variable fan speed capability permits the use of a full-size 52” fan even in smaller
rooms. For very large rooms, two fans may be needed.
SLOPED CEILING INSTALLATIONS
Suggested Extension Pole Lengths
Ceiling Height
8’
8’ 6”
9’
9’ 6”
10”
11”
12”
13”
14”
Pole Length
Standard
Standard
6”
12”
12”
18”
24”
36”
48”
When to Use Extension Poles
For best performance and best appearance, an
extension pole should be used with your Casablanca fan when installing on high (cathedral)
ceilings or sloped ceilings. Casablanca offers
standard poles in increments of 6” up to 5’.
Custom poles are available in lengths up to
9’ 9”. See your Authorized Casablanca Dealer
for details.
Note: Fan may wobble or vibrate if
pole length is not long enough and
inside blade is too close to downslope
or side wall. Extending pole length
will usually solve problem.
Calculation of 32°
Use the tear-off Ceiling Angle Template card inserted in the
back of this manual, it provides you with a simple ‘go’ or
‘no-go’ for installing your fan on a sloped ceiling.
2
Extension Pole
maximum hang-tru®
angle 32º
blades must be a minimum of 7’ above the floor
7′ minimum
EXAMPLE 1
This slope is less than 32˚.
It is OK to install your fan.
EXAMPLE 2
This slope is 32˚. This is the maximum
slope that will allow the fan to hang
straight down. It is OK to install your
fan.
EXAMPLE 3
This slope is more than 32˚.
Your fan will not hang straight down,
an adaptor is necessary. Contact your
local Authorized Casablanca Dealer in
regards to purchasing a “Slope Ceiling
Adaptor.”
Bel Air®
INSTALLING INSTRUCTIONS
Unpacking: Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check them
against the parts listed here. Before discarding packaging material, be certain that all parts have been removed.
IMPORTANT! To avoid possible damage to the Halogen bulb holder the fan must be placed on the styrofoam packaging
from the box. After removing the top cover from the upper half of the styrofoam, take the packaging from the box and
put it on the floor. Place the fan in the recessed circle that the top cover was in.
PERMA•LOCK HARDWARE
ALLEN SET SCREW
1
⁄4-20 x 1⁄4”
(pre-installed)
allen
downrod & Ball
assembly
WRENCH
FAN PREPARATION
important safety information!
motor
wires
before starting the installation of your ceiling fan,
install the threaded downrod into the
motor coupling and lock the assembly
ground
wire
Prepare for fan installation as follows:
Step A. Route the wires from the motor through the
Perma•Lock™ downrod and ball assembly.
Tip: The downrod has a tapered thread
that is designed to lock completely when
correctly installed.
Step B. Using the provided allen wrench, loosen the set screw
several turns to allow installation of the downrod. Thread the
downrod into the motor coupling until it stops turning, this
will take at least four and a half full turns.
downrod
& Ball
assembly
tapered
thread
ALLEN
SET SCREW
Step C. Securely tighten the set screw with the provided allen
wrench to ensure safe operation of your fan.
motor
coupling
CAUTION: Failure to fully lock in the downrod
before securely tightening the set screw may
cause the fan to separate from the downrod
during normal operation!
CEILING HARDWARE
additional hardware
CROSSBAR
MOUNTING
BRACKET
WIRE NUT (4)
21/4″ x 8-32 rounded
head screw (2)
1″ x 8-32 rounded
FLAT
head screw (2)
WASHER (2)
GETTING STARTED
Installing a New Ceiling Fixture Outlet Box
If you do not have an existing fixture located where you wish
to place your Casablanca fan, an approved ceiling fixture outlet
box must be installed and wired.
Warning: To reduce the risk of fire, electrical shock, or
personal injury, mount to outlet box marked acceptable for
ceiling fan support using the mounting hardware provided
with the outlet box.
Using Existing Ceiling Fixture Outlet Box
After turning the power OFF at its source (either circuit
breaker or fuse box), lower the old fixture and disconnect
the wiring. Check the ceiling fixture outlet box to be sure
that it is marked ‘Approved for ceiling fan mounting’. If it is
not, a new box must be installed.
3
CROSSBAR MOUNTIING BRACKET INSTALLATION
Proceed with installation as follows:
Step 1. Route the wires from the ceiling outlet box through
the crossbar mounting bracket center hole. Attach the
bracket, with ground wire and ridges down, to the ceiling
fixture outlet box with the mounting hardware included with
the outlet box.
Tighten the screws firmly by hand only, being careful not to
bend the bracket by over tightening.
ceiling
fan
approved
outlet
box
ridge
side
down
ceiling
wiring
crossbar
mounting
bracket
CAUTION: To reduce the risk
of personal injury, use only the
mounting hardware provided
with the approved outlet box
to install the crossbar mounting bracket.
green
ground
wire
flat
washer
outlet box
mounting
hardware
CANOPY/GLASS HARDWARE
CANOPY SCREW
(4)
CANOPY LOCK WASHER (4)
CANOPY
HATCH
CANOPY
GLASS SHADE
HALOGEN BULB
100 Watt
CANOPY INSTALLATION
Step 2. Attach the canopy to the crossbar mounting bracket with three of the 8-32 x 21/4″ long
canopy screws and canopy lock washers.
Tighten the screw firmly by hand only.
Note: On sloped ceilings, align the
canopy opening towards the top or
room peak.
crossbar mounting
bracket installed
canopy
canopy lock
washers
canopy
screws
4
BODY TOP
COVER
Bel Air®
INSTALLING THE FAN BODY TOP COVER
IMPORTANT! To avoid possible damage to the
Halogen bulb holder the fan must be placed on
the styrofoam packaging from the box. After
removing the top cover from the upper half of the
styrofoam, take the packaging from the box and
put it on the floor. Place the fan in the recessed
circle that the top cover was in.
top cover
retaining
Screws
Step 3. Locate the three tabs on the top of the fan
motor assembly.
Remove the three top cover retaining screws and set
aside for Step 6.
Step 4. Locate the top cover and note the three
mounting tabs on the top.
NOTE: Make a note of
the Fan Serial Number and
Model Type before installing the top cover.
Step 5. Lower the top cover over the fan downrod
with the top cover mounting tabs lined up with the
tabs on the fan motor assembly.
top cover
mounting
tabs
Step 6. Once the tabs are aligned, attach the top cover to the
motor using the three top cover retaining screws removed in
Step 3. Hand tighten ensuring that all screws are engaged.
Test that the cover is on securely before continuing with the
installation.
fan motor
assembly
top
cover
top cover
retaining
Screws
5
HANGING THE FAN
Step 7. To hang the fan body in the
canopy, hold the fan body firmly and insert
the ball into the canopy opening. Check
that no wires were pinched. Rotate the fan
body until the slot in the ball fits into the
pin opposite the canopy opening.
ball
Note: Fan weighs 24 lbs.
slot
pin
CANOPY ELETRICAL CONNECTIONS
Step 8. Attach the fan wires to the
ceiling fixture outlet box wiring by
twisting the bare ends of the wires
together and then securing with a
wire nut.
Connect in this order:
• GREEN leads from mounting plate
and fan to GROUND conductor of
power source. Secure with wire
nut.
• WHITE wire from fan to white NEUTRAL wire in ceiling fixture outlet
box. Secure with wire nut.
• BLACK wire from fan to black (or red)
POWER wire in ceiling fixture outlet
box. Secure with wire nut.
BLACK
wires
(2)
WHITE WIRES
(2)
GREEN WIRES
(3)
wire nut
CANOPY HATCH INSTALLATION
Step 9. Tuck the wires into the canopy
with the wire nuts pointed upwards,
so that the WHITE and BLACK wires
are on opposite sides of the canopy
and all wires are clear of the canopy
opening.
Step 10. Install canopy hatch with the
last canopy screw and lock washer. To
do this, tilt the fan body away from the
hatch opening.
Step 11. Straighten the fan, then
check to ensure that there is no
movement between the canopy and
ceiling or Hang-Tru ball and top support shaft.
6
canopy
hatch
canopy
washer
canopy
screw
tilt the
fan to
install
last
canopy
screw
Bel Air®
BLADE HOLDER HARDWARE
BLADE SCREW (4
PER BLADE)
flat WASHER
(4 per blade)
CENTER STYLE BLADE HOLDER & BLADE
Step 12. Blade Installation
Attach the blades to the
blade holders with four blade
screws and four steel washers
provided for each blade.
Hand tighten securely.
BLADE SCREW
(4 PER BLADE)
flat WASHER
(4 PER BLADE)
INSTALLING THE HALOGEN BULB
Step 13. Screw the 100 Watt Halogen bulb into the socket.
Do not touch the glass bulb with your fingers–it is extremely
important that the glass be clean. If it is touched, or dirty,
clean carefully with a tissue. A dirty glass bulb will cause the
bulb to fail almost immediately.
IMPORTANT! When installing the halogen bulb,
carefully cut off the end of the plastic sleeve the bulb
comes in and hold the bulb by the plastic sleeve to
screw it into the socket.
HALOGEN BULB
100 Watt
INSTALLING THE GLASS SHADE
Step 14. Position the indentations in the outer rim of the glass
shade so that they line up with the tabs on the inside surface
of the fan light fixture rim.
tabs
light
fixture
Step 15. Carefully lift the glass shade up inside the light fixture
as far as it will go.
Step 16. Rotate the shade in a clockwise direction until it is
held tightly in place by the three tabs.
TIP: At first the shade is a very loose fit in the
fixture and can be ‘wiggled’ a little from side to
side. It is a great help when rotating the glass shade
to ‘wiggle’ it at the same time.
glass shade
indentation
glass
shade
7
®
3
W-85 CONTROL INSTALLATION
WALL CONTROL AND HARDWARE (not to scale)
W-85
Switch Mounting
Wall Control
Screws (2)
Switch Bezels
(1) White
(1) Almond
White Wall
Plate(1)
Almond Wall
Plate(1)
Wall Plate
Screws
(2) White
(2) Almond
WARNING!
To avoid possible electrical shock, make certain that electricity is turned off at the circuit
breaker or fuse box before attempting any installation or repair procedure
(4) Wire Cap
BEZEL
CAUTION! NOT turning the power OFF at the
circuit breaker or fuse box may cause damage to
the electronics within the wall control and or the PC
board on the fan.
Before installing the W-85 wall control you will need to check and see if you will need to change the bezel on
the front of the wall control from WHITE to ALMOND.
If you are going to use white, skip these steps and go
to wall control installation starting on page 1.The
bezel can be changed at any time before or after
installation. The wall control does not need to be
uninstalled to replace the bezel.
BEZEL
TABS
Figure #1
WHITE
BEZEL
W-85 Wall Control Bezel Replacement installation
as follows
Step 17a. Locate the four (4) tabs holding the bezel to
the front of the switch, then press in on each tab one
at a time, removing the bezel as shown in Figure #1.
LOCATING
PINS (4)
LOCATING
PINS
HOLES(4)
Step 17b. Locate the rubber key pad attached to
the four (4) locating pins as shown in Figure #2 and
remove rubber key pad from the WHITE bezel, also
as shown in Figure #2.
RUBBER KEY
PAD
Figure #2
8
®
3
W-85 Wall Control Bezel replacement:
CONTINUED
-
ALMOND
BEZEL
Step 17c. Reinstall the rubber key pad on to the
four (4) locating pins located on the almond bezel
as shown in Figure #3 and #4.
RUBBER KEY
PAD
Figure #3
Step 17d. To attach the bezel back on to the front
of the switch you will need to align the four (4) tabs
on the bezel with the front of the wall control and
by gently pressing on both top and button of the
bezel at the same time, snap the bezel back on to
the front of the switch as shown in figure #5.
RUBBER KEY
PAD
ALMOND
BEZEL
Figure #4
LOCATING
PINS
(4)
ALMOND
BEZEL
Step 17e. Check your work by pressing on the
light, fan, reverse and power buttons, making sure
that the buttons do not stick and that each switch
functions properly.
BEZEL
TABS
BEZEL
ALIGNMENT
PIN AND HOLE
Figure #5
9
®
3
INSTALLING THE W-85 WALL CONTROL
NOTE: W-85 Wall Control should only be installed on Casablanca's Inteli-Touch® 3 fans with DOWNLIGHTS ONLY.
The wall control installs in the same manner as an ordinary light switch, using an existing wall box and wiring. This
controller is designed to signal the fan microcomputer as well as perform normal switching operations. For this
reason the following precautions must be observed:
1.Use only the Casablanca W-85 wall control.
2.Do not use any additional control with your Inteli-Touch
3 fan (for example, dimmer, or fan speed control).
3.Do not use more than one fan per wall control.
4.No other light fixtures or electrical appliances may be
connected on the circuit controlled by the W-85 wall
control.
SINGLE W-85 INSTALLATION
CAUTION!
Ensure power is turned OFF at the breaker or fuse panel before starting installation.
W-85 is used to describe either white (-11) or almond finish.
If you have multiple Inteli-Touch 3 fans, refer to the section
"Changing Frequency Setting" on page 3.
1.Remove the screws and switch plate from the existing switch
box.
2.Remove the screws holding the switch in the switch box.
3.Pull the existing switch from the switch box to expose the wire
connections.
4.Remove the two wires from the switch.
5.Connect the BLACK wire from the POWER SOURCE that you
just removed from the switch to the BLACK/WHITE STRIP wire
on the W-85 wall control. Secure this connection with a wire
nut.
NOTE: The RED wire is not used in this
application, DO NOT remove the crimped cap
from the wire..
W-85
(FIGURE #1)
2 BLACK
WIRES
6.Connect the second BLACK wire that you just
removed from the switch to the second BLACK
wire on the located on the back of the W-85 wall
control. Secure this connection with a wire nut.
7.Connect the green ground wire coming from the
back of the W-85 control to the ground wire in the
switch box. Secure the splice with a wire nut.
8.Check your work by using the wiring diagrams as
shown in Figures # 1 and #2.
RED WIRE
NOT USED
9. Install the W-85 in the wall box with the two long
screws provided.
10. Install the wall plate with the two color-matched
screws.
(FIGURE #2)
10
W-85
Wall Control
BLACK AND WHITE
STRIPED WIRE
®
3
DUAL W-85 INSTALLATION
To control the fan and lights from two locations (a three-way circuit), use two W-85
wall controls as shown in the wiring diagram in Figure #5. Before installing the
two switches into the wall, place both switches side by side, then locate the 4 dip
switches on the side of the two switches. Then make sure that the dip switches
are set to the same address on both switches as shown in Figure #4. When setting
these dip switches you are setting the channel number that is required to control
both your fan and lights from both sides of the room. If you are installing other
Inteli-Touch® 3 fans within your home you may need to reset the dip switches on
these other fans to a different channel before installing your W-85 wall control into
the wall. Please review the section on channel changing on this instruction sheet.
DIP SWITCHES
CAUTION!
Ensure power is turned OFF at the breaker or fuse panel before starting
installation.
(FIGURE #4)
NEUTRAL
WHITE
GREEN
To control the fan and lights from two locations (a three-way circuit), use two
W-85 wall controls.
BLACK
BLACK
BLACK WITH
WHITE STRIPE
GREEN
GREEN
W-84
W-85
RED
BLACK
BLACK
RED
RED
BLACK
BLACK
RED
BLACK
2. Pull the existing switch from the switch box to expose the wire connections.
W-85
W-84
BLACK WITH
WHITE STRIPE
120V AC
1. Remove the screws and switch plate from the existing switch box and the
screws holding the switch in the switch box.
3. Determine which wire is connected to the common terminal from the power
source (120V AC) of the three-way switch. (The terminal will be marked
on switch).
BLACK
4. Remove the wire from the common terminal of the three-way switch. Connect this
wire to the remaining black/white striped wire on the W-85 control. Secure this splice
with a wire nut.
2 BLACK
WIRES
W-85
Wall Control
5.Remove the two remaining wires from the three-way switch. Connect the black
wire of these wires to a black wire on the W-85 control. Secure the splice with a
wire nut. The remaining red wire is to be connected to the other red wire on the
W-85. Secure the splice with a wire nut.
6.Connect the green ground wire coming from the back of the W-85 control to the
ground wire in the switch box. Secure the splice with a wire nut.
7.Check your work by using the wiring diagrams as shown in Figure #5 on this page.
2 RED WIRES
8.Install the W-85 in the wall box with the two long screws provided.
9.Install the wall plate with the two short color-matched screws provided.
10.Installation of the second W-85 control is identical. Repeat steps 1 through 9.
(FIGURE #5)
BLACK AND WHITE
STRIPED WIRE
11
®
3
OPERATION POWER
The
button is normally left in the on position. Always turn the power off during
cleaning or servicing the fan and during thunderstorms. It is also used to exit or enter additional programs.
The
button must be left on to retain a previously set fan speed or light level.
OPERATION SPEED CONTROL
There are six individual speed settings for the fan; each speed is indicated by an
audible tone of increasing pitch.
FAN CONTROL
To select the desired fan speed:
1. With fan off, press and hold the button labeled
. The fan blades will start rotating
at the slowest speed, and will increase in steps.
2. Release the button when the desired speed is reached.
The fan speed is now in memory and will automatically come on at the same
speed each time the
button is used. To maintain this level of speed, turn
less than one second. To lower speed, turn fan
the fan on by pressing
off, then on by pressing and holding the
button until the desired speed
is reached. When the fan is on, you may increase the speed by pressing and
button until the desired speed is reached, then release it.
holding the
ON - OFF:
A momentary
press of the FAN
button
CHANGE SPEED:
Press and hold
FAN button longer
than one second
OPERATION REVERSING AIRFLOW
The direction of airflow can be changed from downward to
upward or from upward to downward.
To reverse the airflow:
1. Make sure the
is on and blades are Turning.
2. Press the
button.
Note: A four-toned signal
indicates the command was
accepted by the fan. A few
seconds later the fan will slow
to a stop and then reverse
direction.
OPERATION LIGHTS
To turn the lights off and on, press and release the
1) First press/release of the
button for less than one second.
button- The light will turn ON.
2) Second press/release of the
button- The light will turn OFF.
To vary the light brightness at each touch level:
To vary the light brightness:
1. With lights off, press and hold the button. After one second the lights will
come on at their lowest level and gradually become brighter.
2. Release the button when the desired brightness level is reached.
NOTE: Light Operation - the light varies from “bright” to “dim” over
approximately 8 seconds. This sequence will reverse the light when it reaches
the brightest or dimmest level if you continue to hold the LIGHT button.
Release the button when the desired level is reached.
The brightness level is now in the fan memory and will automatically come on at
the same brightness the next time the button is used.
12
LIGHT CONTROL
ON - OFF:
A momentary press of
the LIGHT button
CHANGE BRIGHTNESS:
PRESS AND HOLD
LIGHT BUTTON
LONGER THAN ONE
SECOND
®
3
CHANGING FREQUENCY SETTING
NOTE: All fans leave the factory set to
“1111”
DIP
SWITCHES
You will only have to change the dip switch settings in the remote if you are using
more than one fan in the same area and want to control them separately.
Step 1. Turn power OFF at the circuit breaker or fuse box and at the toggle switch,
for the fan you want to change.
NOTE: DO NOT set dip switch setting in the remote
to ‘0000’, this may cause frequency interference from
other Casablanca Products.
Step 2. Remove the screws and switch plate from the existing switch box.
Step 3. Remove the screws holding the switch in the switch box.
Step 4. Pull the existing W-85 switch from the switch box to expose the dip switches
located on the side of the control as shown in Figure #1.
Step 5. Change the dip switch settings, assuring that they are different from the
previously installed Inteli-Touch® 3 fan.
DIP SWITCHES
SET TO ‘1111’
(Factory Setting)
DIP SWITCHES
SET TO ‘1001’
Step 6. Mount the W-85 Wall Control unit back into the wall electrical box.
Step 7. At the circuit breaker or fuse box and at the toggle switch, turn the power off
for the fan whose frequency you are changing.
Step 8. Within 20 seconds of restoring power to the ceiling fan and the W-85 Wall
Control press and hold both the “FAN” and “REVERSE” buttons as shown in Figure
#2 for 3 seconds, you will hear one tone from the Piezo Buzzer indicating the command has been accepted.
AUTOMATIC DEMONSTRATION PROGRAM
Programmed into every Inteli-Touch® 3 Series fan is an
Automatic Demonstration Program. It can be used to fully
demonstrate and test the operation of the fan.
To enter the demonstration program:
1. Turn
off for at least 5 seconds. This will clear the
fan memory ready for programming.
2. Turn
on.
3. Immediately operate the buttons in the following sequence:
A multi-tone signal will verify the start of the test program
which proceeds as follows:
+
+
+
•
•
•
•
•
•
•
•
Lights slowly increase to full intensity.
Fan accelerates to speed three with audio tones.
Light dims to half intensity.
Fan accelerates to full speed with audio tones.
Fan reverses at full speed with audio tones.
Fan operates at full speed.
Fan turns off with audio tones (blades coast for a short time).
Lights turn off.
The complete cycle lasts slightly over one minute. It will
continue to repeat until the
is turned off for more
than five seconds, cancelling the program.
+
13
®
3
OPERATION SAFE-EXIT® AND LIGHT-MINDER® PROGRAM
NOTE: Both Light-Minder and Safe-Exit programs will always run at the same time.
The Safe-Exit Program gives you about thirty seconds of light when you turn the lights off,
enabling you to exit your home before the lights go out. To enter the Safe-Exit Program:
Safe-Exit
1) To operate the lights for Safe-Exit Program – Press the
button off for at least five
seconds.
2) Turn the Power on. Immediately press the buttons in the following sequence:
+
+
+
. Immediately press the
Button after an audio tone is heard from the
fan controller. The lights will blink to indicate this command has been accepted. The lights will
stay on for 30 seconds and then begin to dim. After thirty seconds have elapsed, the lights will
turn completely off.
3) To cancel the Safe-Exit Program, press the
button off for five seconds.
NOTE: If the lights are left on in the room, the lights will automatically turn
OFF after 2 hours. ( this is Light-Minder)
The Light-Minder Program automatically turns OFF the fan mounted lights after two hours.
To enter the Light-Minder Program:
1) To operate the lights for Light Minder Program – Press the
button off for at
least 5 seconds.
2) Turn the
on. Immediately press the buttons in the following sequence:
+
+
+
. A series of tones will be heard through the piezobuzzer indicating the command has been accepted. Once the lights turn on, they will
automatically turn off after 2 hours.
3) Light operation still remains normal, if you leave the room and turn OFF the lights will blink to
indicate this Safe-Exit command has been accepted. The lights will stay on for 30 seconds and
then begin to dim. After thirty seconds have elapsed, the lights will turn completely off.
4) To cancel the Light-Minder and Safe-Exit Programs, press the
button.
OPERATION HOME-SAFE® PROGRAM
The Home-Safe Program makes an unoccupied home appear occupied by turning the lights
on and off at random times.
To enter the Home-Safe Program:
1) To operate the lights and fan for Home Safe Program – Press the
Button off
for a least 5 seconds.
2) Turn the
on. Immediately press the buttons in the following sequence:
+
+
+
. A series of tones will be heard through the piezo-buzzer and
flashing lights indicating the command has been accepted will follow. This program overrides
all manual control of lights and fan. Once the lights turn on, they will automatically turn off
after 2 hours.
3) The lights will automatically cycle on and off in a controlled sequence as follows: ON 1 hour,
OFF ½ hour, ON 2 hours, OFF 1 hour, ON ½ hour then OFF 2 hours. This seven hour pattern
will repeat continuously so that a different pattern of lighting is seen each day of the week.
4) To cancel the Home-Safe Program, press the
Button OFF for five seconds.
14
Light-Minder
®
3
OPERATION FAN-MINDER™ PROGRAM
The Fan-Minder feature will add to your comfort when used in the bedroom. The program reduces the
speed of the fan each two-hour interval to compensate for cooling night air.
To enter the Fan-Minder Program:
1. Turn the
OFF for at least 5 seconds.
2. Turn the
ON.
3. Immediately operate the buttons in the following sequence:
+
+
+
4. The fan will respond with three descending tones. A timer is now initiated and the fan will reduce one speed for
each two-hour interval. The fan will not, however, descend below the second lowest speed.
5. You may increase the fan speed by pressing and holding the
button until the desired speed is reached,
then release it. The fan will again reduce one speed for each 2 hour interval.
5. To cancel the Fan-Minder Program, turn the
OFF for three seconds.
15
®
3
TROUBLESHOOTING TIPS
Please refer to this troubleshooting guide before requesting service or contacting your dealer for assistance.
PROBLEM
POSSIBLE REMEDIES
Fan will not start
• Check the main circuit fuses, circuit breakers, and wall switch position.
Check all wire connections. Make sure the power is turned off during this
inspection.
• Pin connectors are not making good contact. Check all connections.
• The fan receiver is defective. Replace the fan receiver.
• Reset the frequency setting: Turn the power off at the circuit breaker
for the fan that is not functioning only. Within 20 seconds from restoring
power to the ceiling fan and the W-85 Wall Control press and hold both
the “Fan” and “REVERSE” buttons as shown in Figure #2 for 3 seconds,
you will hear one tone from the Piezo Buzzer indicating the command
has been accepted. The Fan will come on at “low” speed in the reverse
direction.
• Be sure the canopy pin is set properly into the slot on the ball.
• Check that the blade holders have not been bent during installation and
the blades are balanced.
• The hanger bracket and/or the ceiling outlet are attached too loosely. Make sure the hanger bracket is attached tightly to the ceiling outlet box
and the downrod assembly is secured firmly.
• The downrod is attached to the downrod base too loosely. Make sure all
the screws are securely tightened.
• When changing fan speeds, you may hear several audible clicks. This is
normal operation.
• Check and tighten the light fixture retaining screws, glass shade screws,
and/or lightbulb(s).
• Tighten the canopy screws and mounting plate assembly. Make sure
the wire nuts inside the canopy and switch housing are not touching the
metal parts and that they have not fallen off the wire splices. Tighten as
necessary.
• Tighten the blade holders to the flywheel (or Direct Drive motor) and the
blades to the bladeholder screws.
• Make sure all the screws in the motor housing are snug but not overly
tight.
Fan wobbles or shakes excessively
Fan is noisy during operation
Fan does not run on low speed
• If fan is new, it may need to be “broken in.” Run at high speed for several
days.
This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device
may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.
1. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
2. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: Reorient or relocate the receiving antenna, Increase the separation
between the equipment and receiver, Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected. Consult the dealer or an experienced radio/TV technician for help. Note: Any changes or modifications to the
transmitter or receiver not expressly approved by Casablanca Fan Company may void one’s authority to operate this remote
control.
16
Product Specifications
Model Name: Bel Air®
Model Number: 38xx=
Dimensions:
A = 8.6"
B = 13.9"
C = 2.8"
D = 12.2"
E = 5.6"
Weight:
24 lbs.
17
Motor:
Blade Span With:
Blade Pitch:
No. of Blades:
Technology:
Lightbulbs:
XLP-2000®
55"
14°
5
Inteli•Touch® 100-watt halogen (1)
Airflow:
7,174 cfm
Electricity Use: 119 watts
Airflow Efficiency: 60.5 cfm/watt
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement