Casablanca Fan Company 69xxD User's Manual

Casablanca Fan Company 69xxD User's Manual
CONTENTS
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
mounting recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
fan INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
control features:
3-speed operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...... . . . . . . . . . . . . . . . . . . . . 10
READ AND SAVE THESE INSTRUCTIONS
SAFETY FIRST
Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the
product and proper installation; therefore, before attempting to install and operate your Casablanca
fan, read this owner’s manual completely and carefully. Retain this manual for future reference.
CAUTION: To avoid possible electrical shock, make certain that electricity is turned off at
the circuit breaker or fuse box before attempting any installation procedure.
BEFORE YOU START
• All wiring must be in accordance with the National Electric Code ANSI/NFPA 70-1993 and the appropriate local electrical
codes. The National Electric Code requires proper grounding as a precaution against electrical shock. A qualified electrician should be consulted if you are unsure.
• This fan is designed to be installed on an existing electrical outlet box. The outlet box must be UL Listed for ceiling fan
installations, if it is not, a new box must be installed. Casablanca extension poles are available for sloped or high ceiling
installations.
• This ceiling fan requires a grounded electrical supply of 120 VAC, 60 Hz and a minimum 15 amp circuit. The maximum
current requirement for the fan with light fixture is 3.8 amps. The fan uses about 1 amp or 100 watts. Maximum light
current is 2.8 amps or 340 watts of lighting.
• Where wire nuts are employed, be sure all bare wires are within the connectors. When installing the canopy hatch, make
sure all wires are within the canopy and that no wires are being pinched.
For best performance and for your warranty to be valid,
use only genuine Casablanca blades, light fixtures, and accessories.
• The blades in each pack are matched for
equal weight to assure smooth fan operation.
If more than one fan is being installed, be
careful not to mix blades from different
cartons.
• Inspect the contents of your carton for
possible shipping or handling damage and
report any such damage directly to your
authorized Casablanca dealer.
• It is always a good idea to have an assistant
to help with the installation.
• When cleaning, painting, or working near
your fan, be very careful of the fan and
blades. Always turn the power OFF to the
ceiling fan before servicing it, working on
it, or replacing light bulbs.
• Never insert anything into the path of the
fan blades while the fan is in operation.
• Never install a fan over a pool or spa.
• Never operate a fan that has been damaged in
any way. Contact Casablanca Fan Company by
calling 1-888-227-2178, or contact your local
authorized Casablanca dealer for assistance
in obtaining service.
NOTES
FUSE BOX
(Remove fuse for the
circuit you will be
working on)
18″
70″
CIRCUIT BREAKER
(Trip breaker for the
circuit you will be
working on)
PN 6943010
AT1208
84″
1
MOUNTING RECOMMENDATIONS
Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation,
and fan size are all important factors to consider before installation.
Location
Ceiling fans have practical uses in almost every room in your home. We suggest you follow these mounting
recommendations as you decide where to install your Casablanca fan.
• For safety reasons, the fan blades must be a minimum of 7’ above the floor.
• Do not locate the fan in a doorway or above a swinging door.
• In any installation, the tips of the blades must be at least 18” from the wall in order to provide sufficient
clearance for the blades.
• In bedrooms, fans work best when mounted above the foot of the bed.
• In low ceiling locations, our optional Low Ceiling Adaptor (LCA—available at
extra cost) can be used to gain 31⁄2” on certain fan models.
• Over pool tables, be sure to provide plenty of clearance to avoid damage from
pool cues.
• In kitchens be sure to allow for open cupboard doors to clear the fan blades.
• Do not install a fan close to, or over, a pool or spa. High humidity combined
with corrosive gases will destroy the finish and warp the blades.
Fan Size
Variable fan speed capability permits the use of a full-size 52” fan even in
smaller rooms. For very large rooms, two fans may be needed.
SLOPED CEILING INSTALLATIONS
Suggested Extension Pole Lengths
Ceiling Height
Pole Length
8’
Standard
8’ 6”
Standard
9’
6”
9’ 6”
12”
10’
12”
11’
18”
12’
24”
13’
36”
14’
48”
When to Use Extension Poles
For best performance and best appearance,
an extension pole should be used with
your Casablanca fan when installing
on high (cathedral) ceilings or sloped
ceilings. Casablanca offers standard poles
in increments of 6” up to 5’. Custom poles
are available in lengths up to 10’. See
your Authorized Casablanca Dealer for
details.
Note: Fan may wobble or vibrate if
pole length is not long enough and
inside blade is too close to downslope
or side wall. Extending pole length
will usually solve problem.
Calculation of 32°
Use the tear-off Ceiling Angle Template card inserted in the
back of this manual, it provides you with a simple ‘go’ or
‘no-go’ for installing your fan on a sloped ceiling.
2
Extension
Pole
maximum
hang-tru®
angle 32º
32°
blades must be
a minimum of 7′
above the floor
7′ minimum
EXAMPLE 1
This slope is less than 32˚.
It is OK to install your fan.
EXAMPLE 2
This slope is 32˚. This is the maximum slope
that will allow the fan to hang straight
down. It is OK to install your fan.
EXAMPLE 3
This slope is more than 32˚.
Your fan will not hang straight down, an
adaptor is necessary. Contact your local
Authorized Casablanca Dealer in regards to
purchasing a “Slope Ceiling Adaptor.”
New Orleans Centennial®
INSTALLATION INSTRUCTIONS
Unpacking: Before assembling and installing your ceiling fan,
remove all parts from the shipping cartons and check them
against the parts listed here. Before discarding packaging
material, be certain that all parts have been removed.
Note: Only one set of blade holders is supplied. Depending on the fan model and series they will be either the
Commodore Style, the Center Style, the Badge Style with
matching badges, or the Standard Style blade holder.
perma•lock™ hardware
ALLEN SET SCREW
¼-20 x ¼”
(pre-installed)
downrod & Ball
assembly
3mm
allen wrench
Fan preparation
important safety information!
motor
wires
before starting the installation of your ceiling fan, install the
threaded downrod into the motor coupling and lock the assembly
ground
wire
Prepare for fan installation as follows:
Step A. Route the wires from the motor through the
Perma•Lock™ downrod and ball assembly.
downrod
& Ball
assembly
Tip: The downrod has a tapered thread
that is designed to lock completely when
correctly installed.
Step B. Using the provided allen wrench, loosen the set screw
several turns to allow installation of the downrod. Thread the
downrod into the motor coupling until it stops turning, this
will take at least four and a half full turns.
Step C. Securely tighten the set screw with the provided allen
wrench to ensure safe operation of your fan.
tapered
thread
ALLEN
SET SCREW
motor
coupling
CAUTION: Failure to fully lock in the downrod before securely tightening the set screw
may cause the fan to separate from the
downrod during normal operation!
CEILING HARDWARE
additional hardware
CROSSBAR MOUNTING BRACKET
WIRE NUT (4)
21/4” x 8-32 rounded
head screw (2)
1” x 8-32 rounded
FLAT WASHER (2)
head screw (2)
SUPPORT INSTALLATION PARTS
LAG SCREW
/8” #7 X 5” (1)
3
LARGE
FLAT WASHER
3
/8” (1)
3
crossbar mounting bracket INSTALLATION
Note: After removing the old fixture, check the outlet box
to insure that it is supported by a joist or beam across its
upper surface. If not, a 2” x 4” stud must be installed.
JOIST
Step 1. Remove the knockout plug in the center of the outlet box or drill a 1/2″ hole for the lag screw to pass through.
Then drill a 1/4″ guide hole into the joist or beam to a depth
of 3″.
Step 2. Route the outlet box wires through the keyhole slot of
the crossbar mounting bracket as shown. Attach the crossbar
mounting bracket to outlet box with screws provided, assuring
that the outlet box wires are not pinched by the washer.
CAUTION: To reduce the risk of personal injury,
use only the mounting hardware provided with
the approved outlet box to install the crossbar
mounting bracket.
ceiling
wiring
ceiling fan
approved
wiring box
crossbar
mounting
bracket
ridge
side
down
green
ground
wire
flat
washer
WARNING!
SUPPORT DIRECTLY TO
BUILDING STRUCTURE ONLY.
approved
outlet box
hardware
LAG SCREW INSTALLATION
Step 3. With the large washer attached, pass the lag screw
through the center hole of the crosbar mounting bracket
and screw into guide hole. Tighten until outlet box is firmly
mounted to beam. This box must be firmly secured to the
ceiling. We recommend that the ceiling fixture outlet box
be of sufficient capacity enabling it to support the weight
of fan and light fixture under any conditions.
lag
screw
LARGE
WASHER
4
New Orleans Centennial®
CANOPY HARDWARE
CANOPY SCREW (4)
CANOPY
HATCH
CANOPY LOCK WASHER (4)
CANOPY
canopy INSTALLATION
Step 4. Attach the canopy to the crossbar mounting bracket
with three of the 8-32 x 2 1/2” long canopy screws and lock
washers provided with your Casablanca fan. Hand tighten until
snug against the ceiling.
Note: On sloped ceilings, align the
canopy opening toward the top or
peak of the room.
canopy
lock
washer
FEED OUTLET BOX
WIRES THROUGH
CANOPY OPENING
canopy
screw
5
HANGING THE FAN
Step 3. To hang the fan body in the
canopy, hold the fan body firmly and
insert the ball into the canopy opening. Check that no wires were pinched.
Rotate the fan body until the slot in the
nylon ball fits into the pin opposite the
canopy opening.
Note: Independent control of the
light fixture using a W-80 requires
an additional power wire run from
the wall switch to the fan. See Page
10 for wiring.
CAPPED
BLUE
D1-OPTION
WIRE ON
3-SPEED ONLY
FOR INDEPENDENT
W-80 LIGHT
CONTROL
ball
slot
pin
NOTE: The fan weight is 36 pounds.
CANOPY ELECTRICAL CONNECTIONS
PUll chain or
w-40 connections
wire nut
Step 4a. Attach the fan wires to the ceiling fixture outlet
box wiring by twisting the bare ends of the wires together
and then securing with a wire nut. Test that the connection
is secure by pulling on the wire nut. Connect in this order:
2 BLACK & BLUE
D1-OPTION WIRES
(WITHOUT W-80)
Step 4b. Pull Chain or W-40 Wiring Connections
• GREEN leads from mounting plate and fan to GROUND
conductor of power source. Secure with wire nut.
• WHITE wire from fan to white NEUTRAL wire in ceiling
fixture outlet box. Secure with wire nut.
• BLUE wire and BLACK power wire from fan to BLACK power
wire in ceiling outlet box. Secure with wire nut.
2 WHITE WIRES
3 GREEN WIRES
Step 4c. W-80 Wiring Connections
• GREEN leads from mounting plate and fan to GROUND
conductor of power source. Secure with wire nut.
• WHITE wire from fan to white NEUTRAL wire in ceiling
fixture outlet box. Secure with wire nut.
• BLACK power wire from fan to RED wire from W-80 in ceiling outlet box. Secure with wire nut.
• BLUE wire from fan to YELLOW wire from W-80 in ceiling
outlet box. Secure with wire nut.
blue & yellow
WIRES
w-80 connections
black & red
WIRES
2 WHITE WIRES
NOTE: See Page 10 for additional wiring information.
3 GREEN WIRES
CANOPY HATCH INSTALLATION
Step 5. Tuck the wires into the canopy
with the wire nuts pointed upwards, so
that the WHITE and BLACK wires are on
opposite sides of the canopy and all wires
are clear of the canopy opening.
Step 6. Install canopy hatch with the
last canopy screw and lock washer. To
do this, tilt the fan body away from the
hatch opening.
Tighten the screws firmly by hand only,
Step 7. Straighten the fan, then check
to ensure that there is no movement between the canopy and ceiling or Hang-Tru
ball and top support shaft.
6
canopy
hatch
lock
washer
canopy
screw
tilt the
fan to
install
last
canopy
screw
New Orleans Centennial®
BLADE HOLDERS & HARDWARE
BLADE HOLDER SCREW
(2 PER BLADE)
BLADE SCREW
(4 PER BLADE)
BADGE
ASSEMBLE blade holder & BLADE
Step 8. Attach the blades to the
blade holders by first pressing the
blade badge into the blade, then
installing the blade holder using
the four blade screws provided for
each blade.
Hand tighten securely.
BADGE STYLE
BLADE HOLDER
BLADE SCREW
(4 PER BLADE)
BLADE
BADGE
BLADE
blade/blade holder installation
Step 9. Rotate the flywheel so that the
screw holes can be accessed through the
recessed area of the metal plate.
Attach each blade/blade holder assembly
to the motor.
Tighten securely by hand only.
4/5 Blade Combination Flywheel
Your Casablanca fan includes our 4/5 combination flywheel. This flywheel accomodates your preference to use
either 4 or 5 blades on your fan. If you desire a 4-blade
fan, locate the square counterbores on the flywheel and
use these threaded holes to mount the blades. If you
desire a 5-blade fan, locate the round counterbores on
the flywheel and use these threaded holes.
BLADE HOLDER
SCREW
(2 PER BLADE)
= 4-blade mounting hole
= 5-blade mounting hole
7
3-speed ♦ W-40 Wall Control of the Fan
• The W-40 allows the choice of four (4)
different speed settings.
• No light fixture is used.
• Set the FAN pull chain switch to the
HIGH speed setting.
• No changes in household or fan wiring
are required.
• The fan may be turned ON and OFF by
the W-40 wall control.
CAUTION! Failure to set the pull-chain
speed to HIGH can result in faulty
operation of the fan and damage to
the W-40 wall control. To confirm fan
is set to HIGH: Turn W-40 fan speed
switch to ‘HI’ - set fastest fan speed
with pull chain.
R
3-speed ♦ W-80 Wall Control of the Fan & Light(s)
• The fan may be turned ON and OFF
by the W-80 wall control.
• The lights may be turned ON and
OFF by the W-80 and the intensity
adjusted from low to high.
• The fan must be supplied with
two independent 120V AC supply
wires.
• Set the FAN pull chain switch to
the HIGH speed setting.
• Turn the lights ON at the fan.
• The W-80 allows the choice of four
(4) different speed settings.
CAUTION! Failure to set the pullchain speed to HIGH can result in
faulty operation of the fan and
damage to the W-80 wall control.
To confirm fan is set to HIGH:
Turn W-80 fan speed switch to
‘HI’ - set fastest fan speed with
pull chain.
8
3-SPEED ♦ OPERATION
Pull-chain switches on the fan control the fan and lights.
Using the fan control pull-chain switch: Fan off at start.
First pull: fan ON, low speed
Second pull: medium speed
Third pull: high speed
Fourth pull: fan OFF
Using the optional light pull-chain switch: Light off at
start.
First pull: light ON
Second pull: light OFF
Direction of blade rotation is controlled by the reverse slide
switch on the side of the switch housing.
No changes in household wiring are required.
3-Speed
OPTIONAL LIGHT
PULL CHAIN
SWITCH
FAN & SPEED CONTROL
PULL CHAIN SWITCH
REVERSE
SWITCH
3-SPEED ♦ Optional Light Fixture Installation
NOTE: If a separate circuit is used to control the lights from a wall
control, the BLUE D1-Option wire in the canopy should be connected
to that switch leg with the BLACK fan power wire.
1.Refer to light kit instructions to assemble and attach your light
kit correctly.
2.Remove the two 8-32 screws from the switch housing cap.
3.Remove the plug from switch housing.
4.Install pull-chain switch and finger tighten collar on switch.
5.Connect one wire from pull-chain switch to the BLUE D1-Option
wire. Secure splice with a wire nut.
6.Connect other wire from pull-chain switch to BLACK wire from light
kit. Secure splice with a wire nut.
7.Connect WHITE wire from switch housing to WHITE wire from light
kit. Secure splice with a wire nut.
8.At the canopy, connect the BLACK and BLUE wires.
SWITCH
HOUSING
COLLAR
3-SPEED ♦ Optional Wall Control ♦ W-40
The W-40 wall control provides four-speed control of fan from a convenient wall location.
The W-40 is designed to replace a standard wall switch and will fit wall boxes with a depth
of 2” or greater. Not for use with single pull-chain fan/light option wiring.
To install a W-40 wall control in place of an existing wall switch, follow the instructions
on the W-40 package.
Note: No rewiring is required if the fan is replacing an existing light fixture.
Operation of the fan from the wall switch is simple:
1.Turn knob to obtain desired speed setting.
R
CAUTION! Failure to set the pull-chain speed to HIGH can result in faulty operation of
the fan and damage to the W-40 wall control. To confirm fan is set to HIGH: Turn W-40
fan speed switch to ‘HI’ - set fastest fan speed with pull chain.
3-SPEED ♦ Optional Wall Control ♦ W-80
The W-80 wall control provides separate control of fan and light with two separate knobs
from a convenient wall location. The W-80 is designed to replace a standard wall switch
and wall boxes with a depth of 2” or greater. Requires two hot leads from wall box to ceiling wiring box.
To install a W-80 wall control in place of an existing wall switch, follow the instructions
on the W-80 package.
Operation of the fan from the wall switch is simple:
1.Turn the upper knob to the desired fan speed.
2.Turn the lower knob to the desired light setting.
MED
LO
OFF
OFF
MED
HI
HI
MAX
CAUTION! Failure to set the pull-chain speed to HIGH can result in faulty operation of
the fan and damage to the W-80 wall control. To confirm fan is set to HIGH: Turn W-80
fan speed switch to ‘HI’ - set fastest fan speed with pull chain.
9
Troubleshooting
Before Requesting Service: Please follow this troubleshooting guide before contacting your dealer for assistance.
Caring for Finishes: For cleaning, a soft brush or lint-free cloth
should be used to prevent scratching the finish. A vacuum cleaner
brush nozzle can remove heavier dust. Surface smudges or an accumulation of dirt and dust can easily be removed by using a mild
detergent and slightly dampened soft cloth. An antistatic agent
may be used, but never use abrasive cleaning agents. These will
damage the finish. Painted and high-gloss blades may be cleaned
in the same manner.
Blades: Wood finish blades should be cleaned with a furniture
polishing cloth. Occasionally, a light coat of furniture polish may
be applied for added protection and beauty.
Problem
Problem
3-Speed
FAN WILL NOT START
FAN WOBBLES OR SHAKES EXCESSIVELY
FAN NOISY DURING OPERATION
BREAK-IN PERIOD
DOES NOT RUN ON
LOW SPEED
Never Lubricate this Fan!
The precision motor at the heart of your Casablanca fan features
sealed bearings that are lubricated for life. Do not attempt to oil
the motor.
Changing Light Bulbs
Be sure to turn power to the fan OFF at the wall switch or circuit
breaker before changing light bulbs. Replace bulbs with same type
as removed from the fixture. Each fan is rated for a maximum TOTAL
wattage of lighting.
Exceeding the rated maximum allowable wattage for the fan will
burn out the fan electronics module and void the warranty.
possible remedies..
Possible Remedies
Check main circuit fuses, circuit breakers, or wall switch position.
Check all wire connections, making sure the power is turned off during this inspection.
Check that reverse switch is not set in center of throw.
Be sure canopy pin is properly set into the slot on the ball.
Check the screws holding the blade holders to the flywheel (or direct drive motor). Tighten as necessary.
Check that bladeholders have not been bent during installation.
Check and tighten light fixture retaining screws, glass shade screws and/or the light bulb(s) as neccessary.
Tighten the blade to bladeholder screws.
Tighten canopy screws and mounting plate assembly.
Check and tighten blade holders to flywheel (or direct drive motor).
Make sure all screws in the motor housing are snug, but not overly tight.
Check that the wire nuts inside the canopy and switch housing are not touching the metal parts or have
fallen off the wire splices. Tighten or adjust as necessary.
Let fan run at high speed for two (2) hours
If new, “break-in” may be required - run at higher speed for several days
FAN RUNS SLOWLY IN EITHER DIRECTION IF ROTATION IS STARTED BY HAND; WILL NOT REVERSE: Defective reverse switch; defective
capacitor; or open motor winding: Replace reverse switch assembly; replace PCB assembly; or replace motor unit.
FAN WILL NOT OPERATE AT PROPER SPEEDS OR WILL NOT OPERATE AT ANY SPEED: Defective three-speed pull-chain switch assembly; or
defective capacitor: Replace three-speed pull-chain switch assembly; or replace PCB assembly.
For questions or to locate the nearest Casablanca Authorized Service Center
call toll free: 1-888-227-2178
or visit us on the web at: www.casablancafanco.com
Product Specifications
Model Name:
New Orleans Centennial®
Model Number: 69xxD
Dimensions:
NOTE: Dimension B
includes light fixture
and glass.
A = 26"
B = 28"
C = 3"
D = 13"
E = 5.6"
Weight:
36 lbs.
Motor:
Blade Span:
Blade Iron Pitch:
No. of Blades:
Technology:
XLP 2000™
46" or 54”
15°
5
3-Speed
Airflow*:
Electricity Use*:
Airflow Efficiency*:
6,005 cfm
108 watts
58.1 cfm/watt
* Performance data is for fan only. No lighting wattage is
included. Measurements taken with 21” basic blades.
10
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement