Casablanca Fan Company S3 User's Manual

Casablanca Fan Company S3 User's Manual
S3
OWNER’S MANUAL
CONTENTS
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
MOUNTING RECOMMENDATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
FAN INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
CONTROL FEATURES:
VERSA•TOUCH OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
READ AND SAVE THESE INSTRUCTIONS
SAFETY FIRST
Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product
and proper installation; therefore, before attempting to install and operate your Casablanca fan, read this
owner’s manual completely and carefully. Retain this manual for future reference.
CAUTION: To avoid possible electrical shock, make certain that electricity is turned off at
the circuit breaker or fuse box before attempting any installation procedure.
BEFORE YOU START
• All wiring must be in accordance with the National Electric Code ANSI/NFPA 70-1993 and the appropriate local electrical
codes. The National Electric Code requires proper grounding as a precaution against electrical shock. A qualified electrician should be consulted if you are unsure.
• This fan is designed to be installed on an existing electrical outlet box. The outlet box must be UL Listed for ceiling fan
installations, if it is not, a new box must be installed. Casablanca extension poles are available for sloped or high ceiling
installations.
• This ceiling fan requires a grounded electrical supply of 120 VAC, 60 Hz and a minimum 15 amp circuit. The maximum
current requirement for the fan with light fixture is 3.8 amps. The fan uses about 1 amp or 100 watts. Maximum light
current is 2.8 amps or 340 watts of lighting.
• Where wire nuts are employed, be sure all bare wires are within the connectors. When installing the canopy hatch, make
sure all wires are within the canopy and that no wires are being pinched.
For best performance and for your warranty to be valid,
use only genuine Casablanca blades, light fixtures, and accessories.
SAFE USE
• The blades in each pack are matched for equal
weight to assure smooth fan operation. If
more than one fan is being installed, be
careful not to mix blades from different
cartons.
• Inspect the contents of your carton for
possible shipping or handling damage and
report any such damage directly to your
authorized Casablanca dealer.
• It is always a good idea to have an assistant
to help with the installation.
• When cleaning, painting, or working near
your fan, be very careful of the fan and blades.
Always turn the power OFF to the ceiling fan
before servicing it, working on it, or replacing
light bulbs.
• Never insert anything into the path of the
fan blades while the fan is in operation.
• Never install a fan over a pool or spa.
• Never operate a fan that has been damaged
in any way. Contact Casablanca Fan Company
by calling toll free 1-888-227-2178, or
contact your local authorized Casablanca
dealer for assistance in obtaining service.
FUSE BOX
(REMOVE FUSE FOR THE
CIRCUIT YOU WILL BE
WORKING ON)
18″
84″
CIRCUIT BREAKER
(TRIP BREAKER FOR THE
CIRCUIT YOU WILL BE
WORKING ON)
P/N 9343010 REV.B
CAUTION: MOUNT WITH THE LOWEST MOVING
PARTS AT LEAST 2.5 METRES ABOVE FLOOR OR
GRADE LEVEL.
ATTENTION: INSTALLER DE SORTE QUELES
PIÈCES INFÉRIEURES SOIENT À AU MOINS 2.5
MÈTRES AU-DESSUS DU PLANCHER OU DU SOL.
P/D APR01PDG
1
MOUNTING RECOMMENDATIONS
Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation,
and fan size are all important factors to consider before installation.
Location
Ceiling fans have practical uses in almost every room in your home. We suggest you follow these mounting recommendations as you decide where to install your Casablanca fan.
• For safety reasons, the fan blades must be a minimum of 7′ above the floor.
• Do not locate the fan in a doorway or above a swinging door.
• In any installation, the tips of the blades must be at least 18″ from the wall in order to provide
sufficient clearance for the blades.
• In bedrooms, fans work best when mounted above the foot of the bed.
• Over pool tables, be sure to provide plenty of clearance to avoid damage from
pool cues.
• In kitchens be sure to allow for open cupboard doors to clear the fan blades.
• Do not install a fan close to, or over, a pool or spa. High humidity combined
with corrosive gases will destroy the finish and warp the blades.
Fan Size
Variable fan speed capability permits the use of a full-size 52″ fan even in smaller
rooms. For very large rooms, two fans may be needed.
SLOPED CEILING INSTALLATIONS
Suggested Extension Pole Lengths
Ceiling Height
Pole Length
8′
Standard
8′ 6″
Standard
9′
6″
9′ 6″
12″
10′
12″
11′
18″
12′
24″
13′
36″
14′
48″
When to Use Extension Poles
For best performance and best appearance,
an extension pole should be used with
your Casablanca fan when installing on
high (cathedral) ceilings or sloped ceilings. Casablanca offers standard poles in
increments of 6″ up to 5′. Custom poles
are available in lengths up to 10′. See your
Authorized Casablanca Dealer for details.
Note: Fan may wobble or vibrate if
pole length is not long enough and
inside blade is too close to downslope
or side wall. Extending pole length
will usually solve problem.
EXTENSION
POLE
MAXIMUM
HANG-TRU®
ANGLE 32º
32°
BLADES MUST BE A
MINIMUM OF 7′
ABOVE THE FLOOR
7′ MINIMUM
EXAMPLE 1
This slope is less than 32˚.
It is OK to install your fan.
EXAMPLE 2
This slope is 32˚. This is the maximum
slope that will allow the fan to hang
straight down. It is OK to install your
fan.
Calculation of 32°
Use the tear-off Ceiling Angle Template card inserted in the
back of this manual, it provides you with a simple ‘go’ or
‘no-go’ for installing your fan on a sloped ceiling.
2
EXAMPLE 3
This slope is more than 32˚.
Your fan will not hang straight down, an
adaptor is necessary. Contact your local
Authorized Casablanca Dealer in regards
to purchasing a “Slope Ceiling Adaptor.”
S3™
INSTALLATION INSTRUCTIONS
Unpacking: Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check them
against the parts listed here. Before discarding packaging material, be certain that all parts have been removed.
WORK BENCH SETUP
Setup. Remove the bottom foam from the box
and place the fan rightside up in the foam. This
protects the lamp socket during assembly.
NOTE: If this is the second Versa•Touch fan installed in the same area, one of the fans MUST
have its channel changed. Please refer to the
Versa•Touch section on the bottom of page 9.
FOAM
WORK BENCH
PERMA•LOCK™ HARDWARE
ALLEN SET SCREW
1
⁄4-20 x 1⁄4"
(PRE-INSTALLED)
DOWNROD & BALL
ASSEMBLY
3mm
ALLEN WRENCH
FAN PREPARATION
IMPORTANT SAFETY INFORMATION!
BEFORE STARTING THE INSTALLATION OF YOUR CEILING FAN, INSTALL THE
THREADED DOWNROD INTO THE MOTOR COUPLING AND LOCK THE ASSEMBLY
MOTOR
WIRES
GROUND
WIRE
Prepare for fan installation as follows:
Step A. Route the wires from the motor through the
Perma•Lock™ downrod and ball assembly.
DOWNROD
& BALL
ASSEMBLY
Tip: The downrod has a tapered thread
that is designed to lock completely when
correctly installed.
TAPERED
THREAD
Step B. Using the provided allen wrench, loosen the set screw
several turns to allow installation of the downrod. Thread
the downrod into the motor coupling until it stops turning,
this will take at least four and a half full turns.
Step C. Securely tighten the set screw with the provided allen
wrench to ensure safe operation of your fan.
ALLEN
SET SCREW
MOTOR
COUPLING
CAUTION: Failure to fully lock in the downrod before securely tightening the allen set
screw may cause the fan to separate from
the downrod during normal operation!
3
CEILING HARDWARE
ADDITIONAL HARDWARE
CROSSBAR
MOUNTING
BRACKET
2 1/4″ x 8-32 ROUND HEAD
SCREWS (2)
WIRE NUT (4)
1″ x 8-32 ROUND
HEAD SCREWS (2)
FLAT WASHER (2)
GETTING STARTED
Installing a New Ceiling Fixture Outlet Box
If you do not have an existing fixture located where you wish
to place your Casablanca fan, an approved ceiling fixture
outlet box must be installed and wired.
Warning: To reduce the risk of fire, electrical shock,
or personal injury, mount to outlet box marked acceptable for ceiling fan support using the mounting
hardware provided with the outlet box.
Using Existing Ceiling Fixture Outlet Box
After turning the power OFF at its source (either circuit breaker
or fuse box), lower the old fixture and disconnect the wiring.
Check the ceiling fixture outlet box to be sure that it is
marked ‘Approved for ceiling fan mounting’. If it is not, a new
box must be installed.
NOTE: The fan weight is 23 pounds.
CROSSBAR MOUNTING BRACKET INSTALLATION
Proceed with installation as follows:
Step 1. Route the wires from the ceiling outlet box through
the crossbar mounting bracket center hole. Attach the bracket,
with ground wire and ridges down, to the ceiling fixture outlet box with the mounting hardware included with the outlet
box.
Tighten the screws firmly by hand only, being careful not to
bend the bracket by over tightening.
CEILING FAN
APPROVED
WIRING BOX
RIDGE
SIDE
DOWN
CEILING
WIRING
CROSSBAR
MOUNTING
BRACKET
CAUTION: To reduce the risk of
personal injury, use only the
mounting hardware provided with
the approved outlet box to install
the crossbar mounting bracket.
GREEN
GROUND
WIRE
FLAT
WASHER
APPROVED
OUTLET BOX
HARDWARE
CANOPY HARDWARE
CANOPY SCREW (4)
CANOPY
HATCH
4
CANOPY LOCK WASHER (4)
CANOPY
S3™
CANOPY INSTALLATION
Step 2. Attach the canopy to the crossbar mounting bracket with three of the 8-32 x 21/4″ long
canopy screws and canopy lock washers.
Tighten the screw firmly by hand only.
CROSSBAR
MOUNTING
BRACKET
Note: On sloped ceilings, align the
canopy opening towards the top or
room peak.
CANOPY
CANOPY LOCK
WASHER
CANOPY
SCREW
BLADE HARDWARE
BLADE SCREW
(3 PER BLADE)
METAL WASHER
(3 PER BLADE)
BLADE
(3)
BLADE INSTALLATION
Step 3. Assemble the blades to
the motor using the 3 blade
screws and 3 metal washers.
Hand tighten firmly.
BLADE SCREW
& WASHERS
5
HANGING THE FAN
Step 4. To hang the fan body in the
canopy, hold the fan body firmly and insert the ball into the canopy opening.
Check that no wires were pinched. Rotate the fan body until the slot in the
nylon ball fits into the pin opposite the
canopy opening.
BALL
NOTE: The fan weight is 23 pounds.
SLOT
PIN
CANOPY ELECTRICAL CONNECTIONS
Step 5a. Attach the fan wires to the ceiling fixture outlet
box wiring by twisting the bare ends of the wires together
and then securing with a wire nut. Test that the connection
is secure by pulling on the wire nut. Connect in this order:
Step 5b. Wiring Connections
• GREEN leads from mounting plate and fan to GROUND conductor of power source. Secure with wire nut.
• WHITE wire from fan to white NEUTRAL wire in ceiling
fixture outlet box. Secure with wire nut.
• BLACK power wire from fan to BLACK power wire in ceiling
outlet box. Secure with wire nut.
2 BLACK WIRES
2 WHITE WIRES
WIRE NUT
3 GREEN WIRES
CANOPY HATCH INSTALLATION
Step 6. Tuck the wires into the canopy
with the wire nuts pointed upwards, so
that the WHITE and BLACK wires are on
opposite sides of the canopy and all wires
are clear of the canopy opening.
Step 7. Install canopy hatch with the last
canopy screw and lock washer. To do this,
tilt the fan body away from the hatch
opening.
Tighten the screws firmly by hand only,
Step 8. Straighten the fan, then check
to ensure that there is no movement between the canopy and ceiling or Hang-Tru
ball and top support shaft.
6
CANOPY
HATCH
LOCK
WASHER
CANOPY
SCREW
TILT THE
FAN TO
INSTALL
LAST
CANOPY
SCREW
6
S3™
INSTALL BULB AND GLASS
Step 9. Screw the 100 Watt Halogen bulb into the socket. Do
not touch the glass bulb with your fingers–it is extremely
important that the glass be clean. If it is touched, or dirty,
clean carefully with a tissue. A dirty glass bulb will cause the
bulb to fail almost immediately.
IMPORTANT! When installing the halogen bulb, carefully cut off the end of the plastic sleeve the bulb
comes in and hold the bulb by the plastic sleeve to
screw it into the socket.
TABS
HALOGEN BULB
100 WATT
Step 10. Position the indentations in the outer rim of the
glass shade so that they line up with the tabs on the inside
surface of the fan light fixture rim.
Step 11. Carefully lift the glass shade up inside the light
fixture as far as it will go.
GLASS
SHADE
Step 12. Rotate the shade in a clockwise direction until it is
held tightly in place by the three tabs.
GLASS SHADE
INDENTATION
SAVING MONEY WITH YOUR CEILING FAN
I N S U M M E R , the movement of
air creates a cooling “wind chill”
effect. A room can actually feel
several degrees cooler, without setting the thermostat lower.
I N W I N T E R , hot air rises to the
ceiling while cool air settles to the
floor. Trapped against the ceiling,
the warm air is wasted. If you turn
up the thermostat, energy costs
will rise.
R U N N I N G I N R E V E R S E , your
Casablanca fan can recirculate
warm air near the ceiling down
into the living area, providing even
heating and comfort (with a pleasant effect on heating bills).
7
VERSA•TOUCH ♦ INSTALLATION
R
W-42
CONTROL
HOLDER
W-42
CONTROL
DRYWALL
ANCHOR
6-32
(2)
9V BATTERY
WOOD
SCREW
1”
(2)
SCREW
6-32 X 3/8”
(2)
SCREW
6-32 X 1”
(2)
VERSA•TOUCH ♦ CONTROL HOLDER INSTALLATION
CAUTION! Do not use with wall dimmer.
STANDARD
TOGGLE
SWITCH
INNER
MOUNTING
HOLES
REMOVE TABS
ROCKER
TYPE
LIGHT
SWITCH
OUTER
MOUNTING
HOLES
SWITCH
COVER
PLATE
SWITCH
COVER
PLATE
CONTROL
HOLDER
Standard Light Switch
Step 1. Remove the two screws holding the switch cover
plate. Do not remove the cover plate.
Step 2. Orient the control holder as shown and line up
the two inner mounting holes with those on the switch.
Step 3. Install and tighten screws by hand only.
Rocker Light Switch
Step 1. Break off the two tabs by pushing outward.
Step 2. Remove the two screws holding the switch cover plate. Do
not remove the cover plate.
Step 3. Orient the control holder as shown and line up the two outer
mounting holes with those on the switch.
Step 4. Install and tighten screws by hand only.
VERSA•TOUCH ♦ STORING CONTROL IN HOLDER
Wall Installation
Step 1. Locate a
2X4 wall stud in a
convenient location.
Step 2. Orient the
control holder as
shown over the
2X4 stud.
Step 3. Use the 1”
wood screws in either the inner or
outer mounting
holes.
Install and tighten screws by hand
only.
Note: The wall anchors and
6-32 x 1” screws may be used
in situations where mounting
to a stud is not possible. Use
the inner mounting holes.
After securing the anchor, discard the anchor’s pointed
screws and use the 6-32 decor ovalhead screws supplied.
ANCHOR
PANHEAD
SCREW
WOOD
SCREW 1”
DRYWALL ANCHOR
DECOR OVALHEAD SCREW
6-32 X 1”
Control Storage
Angle control in top first in
the holder until the unit
can be gently pushed back
and snapped onto the
bottom rim.
TOP GOES
IN FIRST
Removing
Gently Pull the lower edge
of the control gently out
from the holder.
VERSA•TOUCH ♦ BATTERY INSTALLATION
Remove Battery Door
Turn control on its
front.
Twist a coin to unsnap
the door A. Lift door
away from control B
and remove C.
SNAP PLUG
SOCKET
Install Battery
Press battery into
control aligned as
shown. Observe
proper polarity.
Replace the
battery door.
GUIDE SLOTS
Changes or modifications not expressly approved in writing by Casablanca Fan Co. may void
the user’s authority to operate this equipment.
8
8
VERSA•TOUCH OPERATION
Fan Control
To start the fan. Press the selected speed button to run the fan at the desired speed.
LO
Low speed
MED
Medium speed
HI
High speed
To turn off the fan. Press the FAN OFF
button.
Airflow Direction
To reverse the airflow press the REVERSE button. Reverse operates at any speed whether fan is
on or off. The fan returns to its set speed after reversing.
Light Control
Turn the light on or off independently from the fan by pressing the LIGHT button. Keep pressing
the button in excess of 0.7 seconds, it becomes a dimmer. The light varies from ‘bright’ to ‘dim’
over approximately 8 seconds. This sequence will reverse the light when it reaches the brightest
or dimmest level if you continue to hold the LIGHT button. Release the button when the
desired level is reached.
Auto Resume
Quick (pressing less than 0.7 seconds) on/off operation of the LIGHT button maintains the
desired brightness level set previously.
SEND
SIGNAL
LED
R
VERSA•TOUCH ♦ CHANGING FREQUENCY SETTING
VERSA•TOUCH
CONTROL
(BACK)
Note: All fans leave the factory set to ‘00000’.
You will only have to change the dip switch settings in the remote if
you are using more than one fan in the same area and want to control
them separately.
Step 1. At the circuit breaker or fuse box, turn the power off for the fan
you want to change.
Step 2. Open the battery door of the Versa•Touch control and remove
the batteries.
Step 3. Change the dip switch settings, assuring that they are different
from the previously installed Versa•Touch fan.
Step 4. Re-install the batteries and the battery door on the control.
Step 5. At the circuit breaker or fuse box, turn the power back on for
the fan whose frequency you are changing.
DIP SWITCH
SET TO ‘10000’
DIP SWITCH
SET TO ‘01001’
Step 6. Within 20 seconds of restoring power, push the Hi, Med, and Lo
buttons (in that order).
Note: You may want to label your controls to
assure you do not mix them up.
WARNING: Do not turn the power off at the circuit breaker,
then back on, for the previously installed Versa•Touch fan(s),
as you may inadvertantly change the frequency settings for
it as well.
3
2
1
WITHIN 20 SECONDS OF TURNING
THE FAN ON, PRESS IN THIS
ORDER TO SET NEW FREQUENCY:
1. HI
2. MED
3. LO
VERSA•TOUCH ♦ IF FAN DOES NOT WORK
If the fan is not functioning after installation:
Step 1. Check to make sure that batteries are installed correctly
in the control.
Step 2. Turn the power off to the fan (from the circuit breaker)
for at least 5 seconds.
Step 3. Turn the power back on (at the circuit breaker) and push
the Hi, Med, and Low buttons–in that order–within 20 seconds.
Step 4. The fan should now function properly.
9
CIRCUIT BREAKER
OR FUSE BOX
3
2
1
PRESS IN THIS ORDER TO SET NEW
FREQUENCY:
1. HI
2. MED
3. LO
9
TROUBLESHOOTING
Before Requesting Service: Please follow this troubleshooting guide before contacting your dealer for assistance.
Caring for Finishes: For cleaning, a soft brush or lint-free cloth
should be used to prevent scratching the finish. A vacuum cleaner
brush nozzle can remove heavier dust. Surface smudges or an accumulation of dirt and dust can easily be removed by using a mild
detergent and slightly dampened soft cloth. An antistatic agent
may be used, but never use abrasive cleaning agents. These will
damage the finish. Painted and high-gloss blades may be cleaned
in the same manner.
Blades: Wood finish blades should be cleaned with a furniture polishing cloth. Occasionally, a light coat of furniture polish may be
applied for added protection and beauty.
PROBLEM
PROBLEM
FAN WILL NOT START
Never Lubricate this Fan!
The precision motor at the heart of your Casablanca fan features
sealed bearings that are lubricated for life. Do not attempt to oil
the motor.
Changing Light Bulbs
Be sure to turn power to the fan OFF at the wall switch or circuit
breaker before changing light bulbs. Replace bulbs with same type
as removed from the fixture. Each fan is rated for a maximum TOTAL
wattage of lighting.
Exceeding the rated maximum allowable wattage for the fan will
burn out the fan electronics module and void the warranty.
VERSA•TOUCH
POSSIBLE
POSSIBLE REMEDIES
REMEDIES..
•Check main circuit fuses, circuit breakers, or wall switch position. Check all wire connections, making
sure the power is turned off during this inspection.
•Pin connectors are not making good contact. Check the connections in the switch housing and under the
top cover.
•Battery weak - install fresh battery.
•Fan receiver defective - replace.
•Check the frequency setting: Turn power off, at the circuit breaker, only for the fan not functioning for
at least 5 seconds; turn the power back on; within 20 seconds press the Hi, Med, and Lo buttons (in that
order) to set the frequency of the fan to the control. See Page 9.
FAN WOBBLES OR SHAKES •Be sure canopy pin is properly set into the slot on the ball.
EXCESSIVELY
•Check that bladeholders have not been bent during installation and blades are balanced.
•Hanger bracket and/or ceiling outlet are loosely attached: Make sure that the hanger bracket is tightly
attached to the ceiling outlet box. Make sure that the downrod assembly is secured firmly
•Downrod is loosely attached to downrod base: Make sure that all screws are securely tightened
FAN NOISY DURING
OPERATION
•Check and tighten light fixture retaining screws, glass shade screws and/or the light bulb(s).
•Tighten canopy screws and mounting plate assembly. Check that the wire nuts inside the canopy and
switch housing are not touching the metal parts or have fallen off the wire splices. Tighten as necessary.
•Tighten blade holders to flywheel (or direct drive motor)/and blade to bladeholder screws.
•Make sure all screws in the motor housing are snug, but not overly tight. Defective bulb: Replace bulb.
DOES NOT RUN ON
LOW SPEED
•If new, “break-in” may be required - run at higher speed for several days.
BATTERY LIFE
SEEMS SHORT
•Not using Alkaline batteries: Replace with Alkaline batteries.
LIGHT O.K., NO FAN: Pin connectors are not making good contact, check 9 pin connector under top cover. FAN O.K., NO LIGHT; Defective
receiver; Replace receiver. Defective motor; Replace motor. Broken socket; Replace socket. Defective receiver; Replace Receiver. FAN AND
LIGHT ON FULL, NO CONTROL; Defective receiver; Replace Receiver. MISSING ONE SPEED: Defective receiver; ReplaceReceiver. FAN DOESN’T
CHANGE SPEED, LIGHT O.K.: Replace receiver. FAN O.K., LIGHT NOT DIM: Defective receiver; Replace Receiver. NO REVERSE: Defective
receiver; Replace Receiver. FAN OPERATES ONLY WHEN TRANSMITTER IS CLOSED: Check antenna wire is not touching metal plate. FAN
STARTS WORKING BY ITSELF: Frequency interference; Change frequency as described on Page 9.
For questions or to locate the nearest Casablanca Authorized Service Center call toll free:
1-888-227-2178 or visit us on the web at: www.CasablancaFanCo.com
1.This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions: (1) this device may not cause harmful interference,and (2) this device must accept any
interference received,including interference that may cause undesired operation.
2.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates,uses and can radiate radio frequency energy and,if not installed and used in accordance with the instructions,may cause
harmful interference to radio communications. However,there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception,which can be determined by turning the equipment off and on,the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or
relocate the receiving antenna, Increase the separation between the equipment and receiver, Connect the equipment into an outlet on a circuit different from that to which the receiver is connected,
Consult the dealer or an experienced radio/TV technician for help. Note: Any changes or modifications to the transmitter or receiver not expressly approved by Casablanca Fan Company may void one’s
authority to operate this remote control.
10
10
761 CORPORATE CENTER DRIVE • POMONA, CA 91768
TOLL FREE: 888-CASA-1ST (227-2178)
www.CasablancaFanCo.com
©COPYRIGHT 2000 CASABLANCA FAN COMPANY • U.S. PATENT PENDING
PRINTED IN ROC
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement