Casio | 3793 | User's Manual | Casio 3793 User's Manual

MA0508-EA
Operation Guide 3793
About This Manual
• Button operations are indicated using the letters shown
in the illustration.
• Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the “Reference” section.
General Guide
• Press B to change from mode to mode. After you perform an operation (except for
C) in any mode, pressing B returns to the Timekeeping Mode.
• In any mode, press C to illuminate the display.
Timekeeping Mode
Telememo Mode
Press
World Time Mode
Countdown Timer
Mode
Stopwatch
Mode
Hand Setting
Mode
.
Timekeeping
This watch features separate digital and analog timekeeping. The procedures for
setting the digital time and analog time are different.
• In the Timekeeping Mode, press A to toggle the display between the date screen
and the time screen.
Date Screen
Hour hand
Alarm Mode
Time Screen
Minute hand
Seconds
Press
To toggle between 12-hour and 24-hour timekeeping
In the Timekeeping Mode, press D to toggle between 12-hour timekeeping (indicated
by A or P on the display), or 24-hour timekeeping.
• With the 12-hour format, the P (PM) indicator appears on the display for times in the
range of noon to 11:59 p.m. and the A (AM) indicator appears for times in the range
of midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all modes.
Digital Time Daylight Saving Time (DST) Setting
Daylight Saving Time (summer time) advances the digital time setting by one hour
from Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
.
Day of week
PM indicator
Month – Day
Hour : Minutes
Digital Time and Date
Use the Timekeeping Mode to set and view a digital display of the current time and
date. When setting the digital time, you can also configure settings for summer time
(Daylight Saving Time or DST).
To set the digital time and date
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press B to move the flashing in the sequence shown
below to select the other settings.
To toggle the Timekeeping Mode digital time between DST and Standard Time
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press B once to display the DST setting screen.
3. Press D to toggle between Daylight Saving Time (ON
displayed) and Standard Time (OFF displayed).
4. Press A to exit the setting screen.
• The DST indicator appears on the Timekeeping, Alarm,
and Hand Setting Mode to indicate that Daylight Saving
DST indicator
Time is turned on.
Setting the Analog Time
Perform the procedure below when the time indicated by the analog hands does not
match the time of the digital display.
To adjust the analog time
DST
Seconds
Day
Hour
Month
Minutes
Year
3. When the setting you want to change is flashing, use C and D to change it as
described below.
Screen
FA
OFF
10:08
P
CAAF
6-30
To do this:
Reset the seconds to AA
Toggle between Daylight Saving Time (ON) and
Standard Time (OFF)
Change the hour or minutes
Change the year
Change the month or day
Do this:
Press D.
Press D.
Press D (+) and C (–).
1. In the Timekeeping Mode, press B six times to enter
the Hand Setting Mode.
2. Hold down A until the current digital time starts to
flash, which indicates the analog setting screen.
3. Press D to advance the analog time setting by 20
seconds.
• Holding down D advances the analog time setting at
high speed.
• If you need to advance the analog time a long way, press D and C at the same
time. This locks the high speed hand movement, so you can release the two
buttons. High-speed hand movement continues until you press any button. It will
also stop automatically after the time advances 12 hours or if an alarm (daily
alarm, Hourly Time Signal, or countdown alarm) starts to sound.
4. Press A to exit the setting screen.
• To return to the Timekeeping Mode, press B.
4. Press A to exit the setting screen.
• Resetting the seconds only (without changing the hour, minute, or DST setting)
causes the analog minute hand setting to be adjusted automatically. If you change
the hour, minute, or DST setting, you should also use the procedure under “To
adjust the analog time” to adjust the analog hands accordingly.
• See “Digital Time Daylight Saving Time (DST) Setting” for details about the DST
setting.
• Resetting the seconds to AA while the current count is in the range of 30 to 59
causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are
reset to AA without changing the minutes.
• The day of the week is automatically displayed in accordance with the date (year,
month, and day) settings.
• The year can be set in the range of 2000 to 2099.
• The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to change
it except after you have the watch’s battery replaced.
1
Operation Guide 3793
Telememo
World Time
Telememo lets you store up to 30 records, each
containing name and telephone number data. Records
are automatically sorted based on the characters of the
name. You can recall records by scrolling through them on
the display.
• A Telememo Mode record has a name field and a
number field.
• See “Character List” for details on how the watch sorts
records.
• All of the operations in this section are performed in the
Telememo Mode, which you enter by pressing B.
Remaining
memory
Name
Number
To create a new Telememo record
1. In the Telememo Mode, press C and D at the same
time to display the new data screen.
• The new data screen shows ___, which indicates
that there is no text in the name field.
• If the new data screen does not appear, it means that
memory is full. To store another record, you will first
have to delete some of the records stored in memory.
2. Hold down A until the flashing cursor ( _) appears in
New Data Screen
the name field of the display, which indicates the setting
screen.
3. Use D and C to change the character at the cursor
position in the name field. The character changes in the
following sequence.
.
Press
.
(space)
to
to
to
• You can input spaces, alpha characters, symbols, and numbers in a name. For
details, see the “Character List”.
4. When the character you want is at the cursor position, press B to move the cursor
to the right.
5. Repeat steps 3 and 4 until the name is complete.
• You can input up to eight characters for the name.
6. After you input the name, press B as many times as
necessary to move the cursor to the number field.
• You tell when you are in the name field because of
the long cursor ( _). The number field has a short
cursor ( _).
• The name field has spaces for eight characters, so
you must press B to move the past the 8th character
in order to get to the number field.
• The number field has spaces for 16 digits. Pressing
B until the cursor moves past the 16th digit causes it
to jump back to the first character of the name field.
7. Use D and C to change the character at the cursor position in the number field.
The character changes in the following sequence.
Press
.
Press
.
(space)
World Time digitally displays the current time in 30 cities
(29 time zones) around the world.
• All of the operations in this section are performed in the
World Time Mode, which you enter by pressing B.
World Time
Current time for the
selected city code
The time settings of the Timekeeping Mode and the World
Time Mode are independent of each other, so you must
make separate settings for each. This watch is preset with
a number of city codes, each of which represents the time
zone where that city is located.
• Whenever you change the time setting for any city in the World Time Mode, the
settings of all other cities are changed accordingly.
• If your location is not included in the preset city codes, select the preset city code
that is in the same time zone as your location.
• For full information on city codes, see the “City Code Table”.
Record number
Press
City code
To set the World Time
1. In the World Time Mode, press D to scroll through city
codes.
2. Hold down A until the DST On/Off setting of the world
time starts to flash, which indicates the setting screen.
3. Press B to move the flashing in the sequence shown
below to select the other settings.
DST
Hour
Minutes
4. While a setting is flashing, use D and C to change it.
• Pressing D and C at the same time while any World Time setting is flashing
causes the displayed time to change to the same setting as the current
Timekeeping Mode time.
• While DST On/Off setting is selected (flashing), press D to toggle between
Daylight Saving Time (ON) and Standard Time (OFF).
• While the hour or minutes setting is selected (flashing), use D (+) and C (–) to
change it.
5. Press A to exit the setting screen.
To view the time in another city code
In the World Time Mode, press D to scroll through city codes.
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, use D to display the city code
whose Standard Time/Daylight Saving Time setting you
want to change.
2. Hold down A until the DST On/Off setting of the world
time starts to flash, which indicates the setting screen.
3. Press D to toggle between Daylight Saving Time (ON
displayed) and Standard Time (OFF displayed).
4. Press A to exit the setting screen.
•
The
DST indicator appears on the World Time Mode
DST indicator
display to indicate that Daylight Saving Time is turned
on.
• The above operation toggles all World Time city codes
between Daylight Saving Time and Standard Time. Note
that you cannot make settings for individual city codes.
to
Alarms
8. When the character you want is at the cursor position, press B to move the cursor
to the right.
9. Repeat steps 7 and 8 until you complete number input.
• You can input up to 16 digits for the number.
10. Press A to store your data and return to the Telememo record screen (without
the cursor).
• After you press A to store data, the name flashes for about one second to indicate
that records are being sorted.
• Note that a record must have something input in the name field, otherwise you will
not be able to store it.
To recall Telememo records
In the Telememo Mode, press D (+) to scroll through Telememo records on the
display.
• Only name data appears when you scroll through Telememo records.
• Press A to toggle the screen between the name and number fields.
Name
Alarm time
(Hour : Minutes)
AM indicator
To set an alarm time
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
Number
Press
You can set three independent Daily Alarms. When an
alarm is turned on, the alarm tone sounds when the alarm
time is reached. One of the alarms is a snooze alarm,
while the other two are one-time alarms.
You can turn on an Hourly Time Signal that causes the
watch to beep twice every hour on the hour.
• There are four screens in the Alarm Mode. Two are for
one-time alarms (indicated by numbers AL1and
AL2), one is for a snooze alarm (indicated by SNZ),
and one is for the Hourly Time Signal (indicated by
SIG).
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing B.
.
• The name and number scroll from right to left on the display. A separator ( < ) is
inserted between the last character and first character of the data.
• Pressing D while the last Telememo record is on the display causes the new data
screen to appear.
To edit a Telememo record
1. In the Telememo Mode, use D to scroll through the records and display the one
you want to edit.
2. Hold down A until the flashing cursor appears on the display.
3. Use B to move the flashing to the character you want to change.
4. Use C and D to change the character.
• For details on inputting characters, see “To create a new Telememo record” (step
3 for name input and 7 for number input).
5. After making the changes that you want, press A to store them and return to the
Telememo record screen.
To delete a Telememo record
1. In the Telememo Mode, use D to scroll through the records and display the one
you want to delete.
2. Hold down A until the flashing cursor appears on the display.
3. Press C and D at the same time to delete the record.
• CLR appears to indicate that the record is being deleted. After the record is
deleted, the cursor appears on the display, ready for input.
4. Input data or press A to return to the Telememo record screen.
• To set a one-time alarm, display one of the screens
indicated by an alarm number AL1or AL2. To set the
snooze alarm, display the screen indicated by SNZ.
• The snooze alarm repeats every five minutes.
2. After you select an alarm, hold down A until the hour setting of the alarm time
starts to flash, which indicates the setting screen.
• This operation automatically turns on the alarm.
3. Press B to move the flashing between the hour and minute settings.
4. While a setting is flashing, use D (+) and C (–) to change it.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (A indicator) or p.m. (P indicator).
5. Press A to exit the setting screen.
Alarm Operation
The alarm sounds at the preset time for about 10 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, or until you turn the alarm off .
• Alarm and Hourly Time Signal operations are performed in accordance with the
Timekeeping Mode digital time.
• To stop the alarm tone after it starts to sound, press any button.
• Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen
Displaying the SNZ setting screen
2
Operation Guide 3793
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
Reference
To turn an alarm and the Hourly Time Signal on and off
1. In the Alarm Mode, use D to select an alarm or the Hourly Time Signal.
2. Press A to toggle it on and off.
• The indicators shown below appear on the display when the daily alarm and Hourly
Time Signal are turned on. Each indicator disappears when the corresponding
function is turned off.
Alarm 1
on indicator
Hourly time signal
on indicator
Snooze alarm
on indicator
Alarm 2
on indicator
• The above on indicators appear on the display in all modes.
• An on indicator on the display flashes while its corresponding alarm operation is
sounding.
• The snooze alarm on indicator flashes during the 5-minute intervals between
alarms.
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
Auto Return Feature
• The watch automatically returns to the Timekeeping Mode if you do not perform any
button operation for two or three minutes in the Telememo, Alarm, or Hand Setting
Mode.
• If you leave a screen with flashing digits or a cursor on the display for two or three
minutes without performing any operation, the watch automatically exits the setting
screen.
• Holding down B for about one second in any mode jumps directly to the
Timekeeping Mode. This operation does not work while a setting screen is on the
display.
Scrolling
The C and D buttons are used in various modes and setting screens to scroll
through data on the display. In most cases, holding down these buttons during a scroll
operation scrolls through the data at high speed.
Initial Screens
When you enter the Telememo, World Time, or Alarm Mode, the data you were
viewing when you last exited the mode appears first.
Countdown Timer
Seconds
Hours
Minutes
The countdown timer can be set within a range of one
minute to 24 hours. An alarm sounds when the countdown
reaches zero.
• All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
B.
To set the countdown start time
1. In the Countdown Timer Mode, hold down A until the
hour setting of the countdown start time starts to
flash,which indicates the setting screen.
2. Press B to move the flashing between the hour and
minute settings.
3. While a setting is flashing, use D (+) and C (–) to change it.
• To set the starting value of the countdown time to 24 hours, set 0:00.
4. Press A to exit the setting screen.
To use the countdown timer
Press D while in the Countdown Timer Mode to start the
countdown timer.
• When the end of the countdown is reached, the alarm
sounds for 10 seconds or until you stop it by pressing
any button. The countdown time is automatically reset to
its starting value after the alarm stops.
• Press D while a countdown operation is in progress to
pause it. Press D again to resume the countdown.
• To completely stop a countdown operation, first pause it
(by pressing D), and then press A. This returns the
countdown time to its starting value.
• The countdown timer measurement operation continues
even if you exit the Countdown Timer Mode.
World Time
• The UTC differentials associated with each city code are used to calculate World
Time Mode times, based on the time you set for any one of the World Time cities.
• The UTC differential is a value that indicates the time difference between a
reference point in Greenwich, England and the time zone where a city is located.
• The letters “UTC” is the abbreviation for “Coordinated Universal Time”, which is the
world-wide scientific standard of timekeeping. It is based upon carefully maintained
atomic (cesium) clocks that keep time accurately to within microseconds. Leap
seconds are added or subtracted as necessary to keep UTC in sync with the Earth’s
rotation.
Display Illumination Precautions
The light that illuminates the face uses two LEDs (light-emitting diode) and a light
guide panel that cause the display to glow for easy reading in the dark. In any mode
(except when a setting screen is on the display), press C to illuminate the display for
about one second.
• The illumination provided by the light may be hard to see when viewed under direct
sunlight.
• The light automatically stops illuminating whenever an alarm sounds.
• Frequent use of the light shortens the battery life.
Character List
Stopwatch
Seconds
Hours
1/100
second
Minutes
The stopwatch lets you measure elapsed time, split times,
and two finishes.
• The display range of the stopwatch is 23 hours,
59 minutes, 59.99 seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
• Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing B.
To measure times with the stopwatch
Elapsed Time
Start
Stop
Re-start
Stop
Clear
Split Time
Start
Split
Split release
Stop
Clear
Two Finishes
Start
Split
Stop
Split release
First runner
finishes.
Display time of
first runner.
Second runner
finishes.
Display time of
second runner.
Clear
City Code Table
City
Code
PPG
HNL
ANC
LAX
DEN
City
Pago Pago
Honolulu
Anchorage
Los Angeles
Denver
UTC
Differential
–11.0
–10.0
–09.0
–08.0
–07.0
CHI
Chicago
–06.0
NYC
New York
–05.0
CCS
Caracas
RIO Rio De Janeiro
–––
–––
LON
London
PAR
Paris
BER
Berlin
CAI
Cairo
JRS
Jerusalem
JED
Jeddah
MOW
Moscow
THR
Tehran
DXB
Dubai
KBL
Kabul
KHI
Karachi
DEL
Delhi
DAC
Dhaka
RGN
Yangon
BKK
Bangkok
–04.0
–03.0
–02.0
–01.0
+00.0
+01.0
Other major cities in same time zone
Papeete
Nome
San Francisco, Las Vegas, Vancouver, Seattle, Dawson City
El Paso, Edmonton
Houston, Dallas/Fort Worth, New Orleans, Mexico City,
Winnipeg
Montreal, Detroit, Miami, Boston, Panama City, Havana,
Lima, Bogota
La Paz, Santiago, Port Of Spain
Sao Paulo, Buenos Aires, Brasilia, Montevideo
Praia
Dublin, Lisbon, Casablanca, Dakar, Abidjan
Milan, Rome, Madrid, Amsterdam, Algiers, Hamburg,
Frankfurt, Vienna, Stockholm
+02.0
Athens, Helsinki, Istanbul, Beirut, Damascus, Cape Town
+03.0
Kuwait, Riyadh, Aden, Addis Ababa, Nairobi
+03.5
+04.0
+04.5
+05.0
+05.5
+06.0
+06.5
+07.0
Shiraz
Abu Dhabi, Muscat
HKG
Hong Kong
+08.0
TYO
ADL
SYD
NOU
WLG
Tokyo
Adelaide
Sydney
Noumea
Wellington
+09.0
+09.5
+10.0
+11.0
+12.0
Male
Mumbai, Kolkata
Colombo
Jakarta, Phnom Penh, Hanoi, Vientiane
Singapore, Kuala Lumpur, Beijing, Taipei, Manila, Perth,
Ulaanbaatar
Seoul, Pyongyang
Darwin
Melbourne, Guam, Rabaul
Port Vila
Christchurch, Nadi, Nauru Island
*Based on data as of December 2004.
3
Download PDF

advertising