Casio | B430 | User's Manual | Casio B430 User's Manual

User Guide
B430
5th edition
www.binatonegps.com
Binatone Navigation software
IMPORTANT
IMPORTANT
Satellite signals are required for this product to function in Navigation Mode.
There may be occasions within your home or surrounding area when the signal
strength is limited and Navigation may not be possible.
This is quite normal for product of this type.
You can check the number of satellite signals that the unit is receiving and the
strength of those signals by viewing the GPS Receiver.
If you need help....
The Help line is available from 9:00am to 5:00pm, Monday to Friday, on 0845
345 9677 Calls are charged al Local Call rate (for UK only)
Unpacking your Binatone Navigation System
In the box you will find
·GPS navigation device
·Car mounting kit
·In-car charger
·USB Cable
·User guide
Keep the packaging materials in a safe place in
case you later need to transport the unit. Keep your
sales (till) receipt, which is your guarantee. Before
you can use the unit, you’ll need to fully charge the
battery as described on page 6, please also read
the notes on the page 2.
WARNING:
Your GPS device operates under open sky
conditions in order to receive a satellite signal.
Please ensure that you are not using the device
indoors or in areas where the satellite signal is
weak.
For the first time of use or after a few days of no
use, it may take up to 10 minutes to acquire a
satellite signal. It is recommended to be stationary
during the start up process.
*USB cable can be either used to charge your device with your computer or
update your system (latest map and software, latest safety camera information)
via your computer and the internet (updates are payable). Charging via the USB
cable will take much longer than by mains/car charger and is not advised.
1
Binatone Help Line: 0845 345 9677 (for UK only. Local Call rate)
SAFETY
Safety
The Global Positioning System
The Global Positioning System (GPS) is a satellite based system that provides
location and timing information around the globe. GPS is operated and controlled
under the sole responsibility of the Government of the United States of America,
who are responsible for its availability and accuracy. Any changes in GPS
availability and accuracy, or in environmental conditions, may impact the
operation of you Binatone Carrera Personal Navigation Device (PND).
Using Your PND in the Car
When using your PND while driving it is essential that you drive with due care
and attention. Never modify the settings or program you PND while driving. Only
look at the PND map when it is safe to do so. When mounting the PND in your
car make sure that it does not obscure your view or impede the operation of any
driving controls.
Prohibited Areas
Do not operate your PND in hospitals or near any electrical medical equipment.
Do not operate your PND in aircraft.
Do not operate while sat in a petrol station forecourt.
Battery
Your PND uses a Li-polymer battery. Do not use it in humid, wet or corrosive
environments. Do not operate or store your PND in high temperatures (>60℃) or
in direct sun light. Do not pierce or break the battery casing.
Failure to follow these cautions will invalidate the warranty and may
cause the battery to leak acid, become hot, explode or ignite and
cause injury or damage.
If you come into contact with leaked battery acid wash the contact
area thoroughly and seek medical attention.
The Li-polymer battery contained in this unit must be recycled or
disposed of properly.
Do not dispose of in household waste or burn.
2
Binatone Help Line: 0845 345 9677 (for UK only. Local Call rate)
CONTENTS
CONTENTS
Important……………………………………………………………………….
In the Box ……….………………………………………………………...
01
01
Safety …………………………………………………………………………… 02
The Global Positioning System …………………………………………… 02
Using Your PND in the Car .…………………………………………….. 02
Prohibited Areas .…………………………………………………….…… 02
Battery..…………………………………………………………………….. 02
Contents .………………………………………………………………………. 03
Quick Start Guide ……………………………………………………………
Position of the Controls …………………………………………………
Charging the Battery …………………………………………………….
SD Memory Card ………………………………………………………...
Car Adaptor ………………………………………………………………
Turning the Sat Nav Unit On/Off ………………………………………..
Turning the Sat Nav Unit Off (Sleep Mode) .…………………………..
System Reset …………………………………………………………….
Windscreen Holder Installation …………………………………………
05
05
06
06
06
07
07
07
08
Getting Started …….…………………………………………………………. 09
Starting Up ... ……………………………………………………………… 09
Settings ……………………………………………………………………. 10
Multi-Media ………………………………………………………………… 11
Picture Viewer..……………………………………………………... 11
Document Viewer …………………………………………………... 12
GPS Receiver ……………………………………………………………… 12
Additional maps and upgrades …………………………………………… 13
3
Binatone Help Line: 0845 345 9677 (for UK only. Local Call rate)
CONTENTS
NAVIGATION
1. Introduction………………………………………………………………………… 15
1.1 GPS connection……………………………………………………………… 15 2. Getting Started……………………………………………………………………… 16
3. Navigational Map Screens…………………………………………………………. 16
3.1 Free Navigation………………………………………………………….…... 17
3.2 Route Navigation………………………………………………………..…… 18
4. Browsing the Map………………………………………………………..………… 19
5. Navigation………………………………………………………………….………. 19
5.1 Free navigation…………………………………………………….………… 19
5.2 Route Navigation……………………………………………………..……… 19
6. Go to……………………………………………………………………….……….. 19
6.1 Entering an Address/Postcode…………………………………….…………. 20
6.2 Searching for a POI (Point of Interest)…………………………….………… 22
6.2.1 POI near Current Position………………………………….………… 22
6.2.2 POI in City…………………………………………………..……….. 23
6.3 Selecting an Entry from the Address Book……………………………..……. 23
6.4 Selecting a Recent Destination…………………………………………..…… 24
6.5 Selecting a Point on the Map………………………………………..………... 24
6.6 Entering a set of Co-ordinates……………………………………..…………. 25
6.7 To Navigate Directly Home……………………………………………...…… 25
7. Map Options………………………………………………………………..……….
7.1 North Up/Heading Up………………………………………………..………
7.2 3D/2D……………………………………………………………………..…
7.3 Day/Night……………………………………………………………..……..
7.4 Motorway Sign Post………………………………………………..………..
7.5 Voice Guidance……………………………………………………..………..
7.6 Auto Zoom………………………………………………………..………….
7.7 Simulation Speed…………………………………………………..………...
26
26
26
26
27
27
28
28
8. Settings…………………………………………………………………..………… 28
8.1 Language……………………………………………………...…………….. 28
8.2 Safety Alert……………………………………………………..…………… 29
8.3 Trace Record…………………………………………………..…………….. 29
8.4 Address Book…………………………………………………..……………. 30
8.4.1 Add an Entry………………………………………..………………. 30
8.4.2 Edit an Entry…………………………………………..……………. 31
8.4.3 Delete an Entry……………………………………...………………. 31
8.5 Day/Night Mode…………………………………………..….……………… 32
8.6 Set Home Address…………………………………………..….……………. 32
8.7 GPS Status………………………………………………...…………………. 32
8.8 Miles/Kilometre………………………………………………...……………. 33
8.9 About…………………………………………………………...……………. 33
4
Binatone Help Line: 0845 345 9677 (for UK only. Local Call rate)
CONTENTS
8.10 Time Zone………………………………………………………..………… 33
8.11 Brightness………………………………………………………...………… 33
8.12 Calibration…………………………………………………..……………… 34
9. Route Plan……………………………………………………………..…………… 34
9.1 Navigating………………………………………………..…………………. 34
9.2 Waypoints…………………………………………………………………… 34
9.3 Simulate……………………………………………………………………… 35
9.4 Route Options…………………………………………………...…………… 35
10. Route Navigation Menu…………………………………………………………… 36
10.1 Route Plan………………………………………….……………………… 36
10.2 Detour …………………………………………….………………………… 36
10.3 Cancel Route ……………………………………….………………………. 36
10.4 Go to ………………………………………….……………………………. 37
10.5 Route Information …………………………….…………………………… 37
10.6 Map Options ………………………………….…………………………… 37
10.7 Settings ……………………………………….…………………………… 37
Frequently asked questions …………………………..………………………. 38
The map contains an error / POI’s are missing…………….……………….…. 38
I am experiencing problems getting a GPS fix……………..…………………… 38
Where can I get technical support?……………………………..……………….. 38
Where can I get additional maps and guides…………………..………………… 38
Technical Specifications ………………………………………..………………. 39
EC Declaration of Conformity……………………………...………………… 40
5
Binatone Help Line: 0845 345 9677 (for UK only. Local Call rate)
QUICK START GUIDE
Quick Start Guide
Please make sure that your read all of the information contained within this user
guide before operating this unit.
If you experience any problems, please go through the user guide before contacting
the customer helpline.
Position of the controls
1. Touch Screen
2. Charge Indicator – Displays the battery charging status.
Red or Orange; charging, Green; fully charged.
3. On/Off Switch – Turn the unit On/Off using this switch, if the unit is not to be
used for long periods of time.
4. Reset – System reset switch.
5. Speaker – For voice guidance instructions.
6. Memory Card Slot – For use with SD type cards. Do not remove memory
card while in use.
7. Headphone Jack – Connects to external headphones.
8. USB connector – For data transfer and charging.
9. Sleep mode Button – Switches the unit In/Out off sleep mode, handy when
stopping for short periods to conserve battery power.
6
Binatone Help Line: 0845 345 9677 (for UK only. Local Call rate)
QUICK START GUIDE
Charging the Battery
Before using your GPS device for the first time, we recommend that you charge the
unit for 5 hours via the mains/car charger, or until the charge light turns green.
Plug the mains/car charger into the
USB socket.
NOTE: Charging via USB cable. It is possible to charge the unit via the USB cable
but the charge time will be significantly increased. Also if the battery is very low the
unit will not fully charge.
The charging indicator on the unit will light up red. When fully charged the red light
will turn green.
When using the GPS device in your car, we recommend that you always use the car
charger in order to maintain the battery level.
If you have a SD memory Card, you may install it refer to the picture
(below)
Switch the unit off first before installing or removing the SD card.
When installing it can only be fitted one way – contacts towards you and the cut-off
corner at the top. Slide the card in and push it in so that it clicks in place.
Once the card is installed it does not need to be removed.
If you need to remove the card, push the card in and it will eject from the slot.
Car Adapter
When using your PND in the car we recommend that you always use the in-car
charger to power the unit, especially on long journeys.
Plug the in-car charger into the USB socket of the unit. Pug the other end of the
adapter into the car’s cigarette-lighter / 12V DC socket.
7
Binatone Help Line: 0845 345 9677 (for UK only. Local Call rate)
QUICK START GUIDE
Turning the Sat Nav Unit On/Off
To switch the unit On slide the power switch located on the side of the unit to the On
position, the unit will power up and display the warning screen.
To switch the unit Off slide the power switch to the Off position.
Turning the Sat Nav Unit Off Via Sleep Mode
Press and hold down the sleep button on the top of the unit, after about 3 seconds
the unit will enter sleep mode. Press and hold the button again, to bring the unit out
of sleep mode. When brought out of sleep mode the unit will show the same screen
as when the unit entered sleep mode.
If the unit is not to be used for a long period of time it is advised that you slide the
power switch on the side of the unit to Off.
System Reset
Under extreme circumstances it may be necessary to reboot the system. Reset the
system if the following situation occurs:
• Long delay experienced with screen refresh rate or operation, resulting in an
inoperable unit.
• The system will not turn Off with the power button.
• No response with selection made on the screen.
The reset button can be found on the back of the unit. Insert the tip of the stylus pen
into the reset switch in order to press. The system will be immediately reset.
8
Binatone Help Line: 0845 345 9677 (for UK only. Local Call rate)
QUICK START GUIDE
Windscreen Holder Installation
The car mount has a suction pad that fits to the windscreen or a flat area on the
dashboard.
A. Fitting to windscreen
Pull the lever away from the suction pad. Place the pad on the widescreen and push
the lever towards the pad until it clicks into place.
B. Fitting the holding bracket
It is best to fit this to the unit before it is attached to the windscreen.
With the lever facing down, slide the bracket onto the securing lug on the end of the
car mount, making sure that the top of the bracket is not located on the same side as
the lever.
C. Fitting the Unit
Slide the unit into the bottom of the bracket and carefully push the unit up until it
clicks into place at the top.
To remove the unit from the car mount; Press and lift the tab at the top of the bracket
then pull the unit forward and up out of the bottom of the bracket.
To remove the Car mount from the windscreen; Lift the lever away from the
windscreen, then gentle pull the tab on the suction cup to release the suction as you
pull the mount away from the windscreen.
9
Binatone Help Line: 0845 345 9677 (for UK only. Local Call rate)
GETTING STARTED
Starting Up
Turn the ON/OFF button on the back of the unit to ON.
The following screens will be displayed:
When you press MENU, the following screens will be displayed:
10
Binatone Help Line: 0845 345 9677 (for UK only. Local Call rate)
GETTING STARTED
Settings
NOTE: You do not need to enter the SETTINGS menu before you start to navigate.
If you press on the SETTINGS icon the following screen is displayed.
To exit this page or exit any subsequent page, press the cross at the top of the
screen.
Volume
Press ’volume’ you can modify the volume level of the voice prompts. You can
increase or decrease the level by clicking “
” or “
”. This can also be done via
the navigation software later.
Backlight
Press ‘Backlight’ to change the brightness of the screen. You can make it darker or
brighter by clicking “
” or “
”. This can also be done via the navigation software
later.
Time & Date
This device can auto-set the current date and time by receiving three GPS signals.
However you can also change it by yourself by
1.) Click
2.) Clicking on
and
to scroll to the right year, month, date, time and time
format.
Note: the unit does not save the time & date when the unit is switched off, this
is because the unit automatically sets the time & date from the satellite
signals.
Power
The power page contains the information of your battery level.
Language
Press ”Language” to change the language by clicking << and >>
About
The About page contains information about your software version.
It also allows you to default the unit or to calibrate the screen to your touches.
The unit will be returned to how it was when it left the factory. After selecting this
option you will be asked to confirm.
11
Binatone Help Line: 0845 345 9677 (for UK only. Local Call rate)
GETTING STARTED
Default
Reset to factory default settings.
Calibrate
This function calibrates the unit to respond to your screen taps. You will need to use
this function only if the unit begins to respond inconsistently to your screen taps, then
follow the on screen dissections. Once the calibration has been completed, press
anywhere on the screen to return to the previous menu.
Multi Media
NOTE: if you press on the MULTI MEDIA icon the following screen is displayed.
Picture Viewer
This device supports, .bmp, .jpg and .gif file formats only (recommended picture size
for optimum usage: 500kb – it is not recommended to view pictures over 2mb). Press
the “Picture viewer” to show a list of names for all the picture files then click on the
file you want to view.
To view pictures (bmp and jpeg formats only):
1) Copy all the pictures you want to view onto a SD card.
2) Insert your SD card into the PND.
3) Select Multi Media and then Picture viewer a list of pictures or folders containing
pictures will be shown.
4) Click on folder to open it and then click on a picture to load it into the viewer.
The following screen will be shown:
12
Binatone Help Line: 0845 345 9677 (for UK only. Local Call rate)
GETTING STARTED
Document Viewer
This device supports, txt file format viewing only. Press the “Doc Viewer” to show the
list of files available for viewing. The procedure for viewing documents is the same
for viewing pictures. But once loaded the following screen will be shown.
GPS Receiver
NOTE: This page is for information only. You can view the number of satellite signals
the unit is receiving also the strength of these signals.
This page gives your current position in degrees longitude and latitude, your current
speed and the status of your position, i.e. Fixed 3D or Fixed Invalid etc.
The compass circle shows the satellites that the unit is receiving and the bar chart
below
13
Binatone Help Line: 0845 345 9677 (for UK only. Local Call rate)
GETTING STARTED
NOTE:
At least four GPS signals are required for the PND to function .
There may be occasions within your home or surrounding area when the
signal strength is limited and GPS navigation Mode may not be possible.
This is quite normal of products of this type.
Additional maps and upgrades:
Please visit www.binatonegps.com or contact the helpline on 08452 459677 for
more information.
14
Binatone Help Line: 0845 345 9677 (for UK only. Local Call rate)
INTRODUCTION
Introduction
You have chosen a cutting-edge navigation system. Congratulations! Please enjoy
using it. This navigation system leads you straight to your destination, whether you
are travelling by car or on foot. You can navigate and plan your route with an easyto-use and intuitive interface, just by using your finger. You can also use this
application to plan your trip to suit your personal preferences and interests and to
save interesting destinations before your set off on your journey.
This manual leads you through the main features of the system.
GPS connection
Your navigation device uses GPS technology for navigation. The device receives
signals from a number of GPS satellites in order to determine your current position.
• Place your navigation device in a location with an unobstructed view to the sky to
set up your first satellite connection. In the car this will usually mean mounting the
unit on the lower part of the windscreen.
Note; It may take up to 10 minutes to establish the first connection.
Subsequent connections will be faster (30 seconds to 1 minute), but if you
have not used the unit for several days or are far away from the last location
where you used the unit, it may take up to 10 minutes again to find a strong
signal.
15
Binatone Help Line: 0845 345 9677 (for UK only. Local Call rate)
NAVIGATION MENU
2 Getting Started
Please make sure that the battery in your device is charged (see page 7).
Switch on the unit and from the menu select Navigation. The navigational software will start to
load.
First you will see the warning statement screen. Tap
on “Accept” to confirm that you have read the
statement and to continue. If you do not wish to be
shown this screen in the future check the box next to
“Don’t show this statement again”. You will now be
shown the Binatone screen, which shows the progress
of the loading software on the yellow bar at the bottom.
Once the software has loaded you will be shown the
Free Navigation Menu screen, this is the starting point
for all your navigating needs.
For more information on free navigation mode (see
page 17).
In order to enter destinations and access the many
settings of the navigational software, tap Menu. This
will then take you to the Free Navi Menu screen.
You can choose from the 3 following options;
Go to – Opens the Search Menu screen. From here
you can select a point to navigate to.
Map Options – Allows you change the way the map
looks and behaves during navigation.
Settings – Allows access to the main settings menu of
the unit, which you can set to your personal preference.
- Tap to return to the Free Navigation mode
- Tap to exit Navigation. You will be asked to confirm if you wish to exit, tap Yes to
exit, tap No to cancel and return to the Free Navi Menu.
- Returns you to either the Free Navigation screen or Route Navigation screen if a
route has been planned. This option is always available when not on any Navigation
screen.
3 Navigational Map Screens
The navigational map screens will be the most frequently used screens. The two navigation
screens are free navigation and route navigation and are shown below. Though the screens look
very similar there are some differences.
16
Binatone Help Line: 0845 345 9677 (for UK only. Local Call rate)
NAVIGATION MENU
3.1 Free Navigation
1 Compass –
Shows your current heading by means of a letter, while the red part of the
compass needle always points North.
2 Zoom out –
Tap to zoom out on the map.
3 Speed –
Shows your current speed.
4 Menu button –
Tap to access the Free Navi Menu screen. (Only when in Free Navigation)
5 Time –
Shows the current time (Note; this is set when you have a valid GPS lock).
6 Map scale –
Show a scale bar which changes as the map zoom level is altered.
7 Volume –
Tap to access the volume control menu.
8 Zoom in –
Tap to zoom in on the map.
9 GPS reception – Shows the current status of the GPS signal, Shown greyed out if you do not
have a valid signal and white if you do. Tap to enter the GPS status screen
(see page 32).
10 Position icon – Shows your current position on the map as well as showing your current
direction of travel.
17
Binatone Help Line: 0845 345 9677 (for UK only. Local Call rate)
NAVIGATION MENU
3.2 Route Navigation
11 Speed limit–
Shown when you exceed the speed limit of the current road, if switched on via
the settings (see page 29).
12 Turn indicator – Shows a graphical representation of the next manoeuvre and the distance to
the manoeuvre. Tap to replay the voice instruction.
13 Current road – Shows the name of the road you are currently on.
14 Menu button - Tap to access the navigation options. (Only when in Route Navigation)
15 Distance –
Shows the remaining distance to your destination.
16 Arrival time –
Shows the estimated time you will arrive at your destination.
17 POI icon –
Show the position of a point of interest.
18 Next road –
Shows the name of the road you will be using next.
19 Route –
Indicates the planned route to be followed.
18
Binatone Help Line: 0845 345 9677 (for UK only. Local Call rate)
NAVIGATION MENU
4 Browsing the Map
When in Free Navigation or Route Navigation it is possible to browse the map so that you can look
at parts of the map which are currently not shown.
To move the map around use the stylus (if provided) or your finger to press and hold on a point on
the map, then drag the map in the opposite direction you want to look at. E.g. to view the map
above the currently shown section, press on the screen and move the stylus (if provided) or your
finger down, the map will then re-draw to show the new section of map.
You can also change the zoom level of the map to be shown more detail or a larger section of the
map. In order to zoom simply tap on the
and
. Each tap will zoom the map one level.
You can tap on roads or Point of Interest icons shown on the map to be given more information
relating to that point.
After moving the map from the starting location you will see the following icon appear
Tapping on this icon will return you to your current or last known GPS position.
,
5 Navigation
There are two modes of navigation; Free navigation and Route Navigation.
5.1 Free navigation
In free navigation the unit does not have a planned route for you to follow, so simply plots your
GPS position on the map and then follows your movement as you drive. The unit shows you the
current time and date, as well as your current position in latitude and longitude co-ordinates.
5.2 Route Navigation
In route navigation the unit directs you via the map and with spoken directions to your chosen
destination. In order to plan a route you need to have a valid GPS signal, this can be easily
checked by looking at the GPS reception screen on the free navigation screen. If the icon is
greyed out then there is no valid signal, if the icon is white with green signal waves then you have
a valid GPS signal and navigation is possible.
From the Free Navi Menu screen select Go to, this allows you to enter your destination.
6 Go to
Tapping this opens up the Search menu screen,
from here you can enter a destination to navigate
too in several different ways. Each will be
described in turn in the pages that follow.
19
Binatone Help Line: 0845 345 9677 (for UK only. Local Call rate)
NAVIGATION MENU
6.1 Entering an Address/Postcode
One of the most commonly used methods for inputting a destination into the unit, tap Address the
screen will change to show the following.
This screen shows a list of any previously used
cities/towns. You will also be able to enter a new
city name as well as changing the country you
wish to search within. Every time you enter a new
city it will be added to the list of recent cities so
that it can be quickly used in the future.
To select a previously used city, select the city
from the list so that it is highlighted orange and
to accept or double tap on the city
then tap
name, the screen will change to the Address
Search window with the selected city now shown on the city field.
To change the country tap on the currently selected country name, this will be defaulted to United
Kingdom. A new screen will open with a list of all available countries (note: the list of countries will
depend on the model of unit you have purchased, e.g. UK & ROI or Western Europe). Use the
or
keys to move through the list until you see your desired country. Then select the country
to accept or double tap the country
from the list so that it is highlighted orange and then tap
name. Alternatively tap in the white text box which shows the name of the currently selected
country, you will be shown a keyboard screen. Enter the name of the country you are looking for
and tap
. Tap
to accept or double tap the country name. Now the screen will change
to show either a keyboard if no previous city has been entered which allows you to enter the name
of the city or postcode you are looking for or you will be shown a list of previously entered cities as
covered above.
If the country is correct and the required city does not appear on the previously used list or you
wish to enter a postcode. Tap on the white box at the top of the screen which says “Click Here”,
this will open a keyboard which allows you to enter the name of the city or the postcode you are
looking for.
Tap on the keyboard characters to enter the
name of the city or Postcode you are
looking for. As you enter characters the
keyboard will start to blank out letters, this is
because the unit is narrowing down the
search and only showing characters which
can be entered.
The number in the top right of the white box
shows the number of possible matches.
Continue entering characters until the unit
narrows the search down to a point where
the remaining possible matches will be
shown on a list, or when the
is shown in white, tap it to be shown all remaining matches.
Scroll through the remaining matches, select the correct city/postcode from the list and tap
20
Binatone Help Line: 0845 345 9677 (for UK only. Local Call rate)
NAVIGATION MENU
to confirm or double tap the list item. The screen will change to the Address Search window with
the selected city now shown on the city field.
Note: That there is no need to enter any special characters in the city name as the unit will search
for and match whether these are entered or not. E.g. for CÁDIZ simply enter CADIZ.
Tap
or
(number keyboard) to enter a space.
Tap
to delete an incorrect letter.
Tap
or
to change between numbers and letters (number keyboard only).
Tap
to change the keyboard language if available, you can now access the language’s
special characters by tapping as above. (see page 28 for how to select keyboard language).
Tap
to cancel entering address information and to return to the Address Search screen.
Once the city/postcode has been entered, you will be taken to the Address Search screen.
If you entered a postcode the road will be automatically entered in to the Address Search screen.
You can continue entering address information in order to narrow down your destination even
further.
UK & ROI Version
Tap on the Road field to enter a road name, you will be taken to the keyboard screen again. As for
when entering a city name the unit will begin matching the name and narrowing down the possible
matches.
Western Europe (WEU) Version
Tap on the Road field to enter a road name, you will be taken to the keyboard screen again. But
this time the name will not be matched as you go. Enter the full road name or as much of the road
name as you know then tap OK. You will be shown a list of all possible matches.
NOTE: For the Full Europe (FEU). The unit will match City and Road names for countries in
Western Europe, But will not match City and Road names for countries in Eastern Europe.
Tap on the House No. field to enter the house number, you will be taken to the keyboard screen
again. If the house number cannot be found you will be taken to the default position.
Tap on the Crossroad field to select a point where another road joins the entered road. The screen
will change to show a list of all joining roads, use the
or
keys to move through the list until
21
Binatone Help Line: 0845 345 9677 (for UK only. Local Call rate)
NAVIGATION MENU
you see the correct road. Select the desired road and tap
or double tap to confirm. You can
also enter the name of the road by tapping on the white box at the top.
When entering an address you have the following options;
Tap
. Once you have fully entered the destination you want to navigate to and are happy,
you will now be taken to the Route Plan screen (see page 34).
Tap
to view the location on the map and once in the map view you can browse the map
(see page 24), to exit from the map view back to the previous screen tap
. You also have
the option of selecting a point from this map to navigate to. This can be used to exactly pin point
your destination, or allow you to quickly select a point on the map to navigate to without having to
scroll the map to the area you wish to select around. Place the cursor on the point you would like
. You will be taken directly to the Route Plan screen and your selected
to navigate to and tap
point will be entered as the destination.
Tap
to cancel entering an address and to return to the Search Menu screen.
6.2 Searching for a POI (Point of Interest)
The POI search allows you to quickly find points of
interest like petrol stations and places to eat in a
database of millions of POI. These places can be
either close by or at a distant location.
Tap POI to begin searching through the POI
database.
When tapped the screen will change to the POI
Menu, with two options available for searching for a
POI near Current Position and POI in City.
6.2.1 POI near Current Position
Use this option to search for a POI from a
particular category or for all categories around
your current location as shown on the map (this
will either be your current GPS position or the
position where you last had a GPS lock).
From the POI category screen select the
category for which you want to search in and tap
. The screen will change to show you all
the POI for that category which are near your position starting with the closest.
Scroll through the list using the
or
keys till you
find the POI you are looking for. Select the item so
or double
that it is highlighted orange then tap
tap the item to confirm. You will be taken to the Route
Plan screen (see page 34).
Alternatively you can tap in the white box at the top of
the screen. This will bring up a keyboard screen,
22
Binatone Help Line: 0845 345 9677 (for UK only. Local Call rate)
NAVIGATION MENU
which allows you to search for the name of a particular POI. After entering the whole name or part
name tap
.
The screen will change to show a list of all possible matching POI, scroll through the list of POI
until you find the one you are looking for and then tap
taken to the Route Plan screen (see page 34).
or double tap to confirm. You will be
At any point tap
to return to the POI
Category screen, if you are on the POI Category
screen tapping will return you to the POI menu etc.
Tap
to view the location on the map and
once in the map view you can browse the map
(see page 24), to exit from the map view back to
. You also have the
the previous screen tap
option of selecting a point from this map to
navigate to, this can be used to exactly pin point your location. Place the cursor on the point you
would like to navigate to and tap
. You will be taken directly to the Route Plan screen and
you selected point will be entered as the destination.
Note; When you carry out a search for a particular name of a POI. The unit will search from a
larger distance around your current position, than it did from the original search.
6.2.2 POI in City
Use this option to search for a POI in and around
a particular city. Before you can search for a POI
you will need to enter the name of the city you
wish to search around. For information on how to
enter the city name, see the section about
entering a city under the Address section (see
page 20).
As with POI near Current Position you will then
need to select a category for your POI. You will
then be shown a list of POI in and around your
entered city.
Alternatively you can tap in the white box at the top
of the screen. This will bring up a keyboard screen,
which allows you to search for the name of a
particular POI. After entering the whole name or
part name tap
.
Scroll through the list of POI until you find the one
or double
you are looking for and then tap
tap to confirm. You will be taken to the Route Plan
screen (see page 34).
Note; When you carry out a search for a particular name of a POI. The unit will search from a
larger distance around your current position, than it did from the original search.
23
Binatone Help Line: 0845 345 9677 (for UK only. Local Call rate)
NAVIGATION MENU
6.3 Selecting an Entry from the Address Book
This option allows you to quickly select one of your
address book entries to use as your destination. Tap
Address Book the screen will change to show the
address book screen and a list of any stored entries.
Scroll through the list of entries using the
or
keys until you find the entry you require. Select it so
that it is highlighted orange and tap
or double
tap to confirm. The screen will then change to show
the Route Plan screen (see page XX).
Tap
Tap
to go back to the Search Menu screen.
to view the location on the map and once in the map view you can browse the map
(see page 24), to exit from the map view back to the previous screen tap
.
Tap
to delete the currently selected address book entry. Warning you will not be asked to
confirm the deletion, so make sure that you wish to carry out this operation before tapping.
Note: In order to use the Address Book option, you will first need to store entries to the address
book. This can be done via the Address Book option in the Settings menu (see page 28).
6.4 Selecting a Recent Destination
This option allows you to select one of your
recently used destinations and to use it again
quickly. Tap Recent Destinations the screen will
change to show the recent destinations screen and
a list of any previously entered destinations.
Scroll through the list of entries using the
or
keys until you find the entry you require. Select it
so that it is highlighted orange and tap
or
double tap to confirm. The screen will then change to show the Route Plan screen (see page 34).
Tap
Tap
to go back to the Search Menu screen.
to view the location on the map and once in the map view you can browse the map
(see page 24), to exit from the map view back to the previous screen tap
.
to delete the currently selected address book entry. Warning: you will not be asked to
Tap
confirm the deletion, so make sure that you wish to
carry out this operation before tapping.
6.5 Selecting a Point on the Map
This option allows you to move around the map and
to select a location which you want to use as your
destination.
Tap Point On Map the screen will change to show the
map. The location of the map will either be your
24
Binatone Help Line: 0845 345 9677 (for UK only. Local Call rate)
NAVIGATION MENU
current/last known GPS position or the last position you viewed on the map.
You can then browse the map (see page 24) and select a point you want to navigate to by placing
the cursor.
After placing the cursor at a point on the map, it may contain further information, i.e. if there is
more than one POI at that point. In this case you can use the
between the multiple points.
Tap
arrows to scroll
to go back to the Search Menu screen.
Tap
to confirm the point. The screen will then change to show the Route Plan screen (see
page 34).
6.6 Entering a set of Co-ordinates
This option allows you to enter the longitude and
latitude co-ordinates of the location you are
looking for. Tap Coordinates the screen will
change to the co-ordinates entry screen.
You can enter the co-ordinates in two different
ways, Degrees:minutes:seconds or as a Decimal,
the unit automatically defaults to the
Degrees:minutes:seconds format (Note: when the
unit displays the co-ordinates of a location it
always shows then in the Degress:minutes:seconds format).
Tap in the white boxes next to either Lon or Lat, then use the keyboard to enter the co-ordinates
you wish to navigate to.
When entering in Degrees:minutes:seconds format.
For Longitude the letters E and W are used to
describe the hemisphere, for Latitude the letters N
and S are used to indicate the hemisphere. ° is used
to indicate the degrees and ‘ is used to indicate the
minutes.
When entering in Decimal format. The N, S, W and E
keys are replaced with + and -, where North and East
are + and South and West are -. Use the . key to
enter a decimal point.
Tap
to change between Degrees:minutes:seconds and Decimal formats.
Tap
to delete any incorrect characters.
Tap
to go back to the Search Menu screen.
Tap
to confirm the entered co-ordinates. The
screen will then change to show the Route Plan
screen (see page 34).
6.7 To Navigate Directly Home
Tapping Go Home will directly navigate you to your
set home address without having to tap any other
keys or enter an address. This is very useful as your
home address will be the destination which is
25
Binatone Help Line: 0845 345 9677 (for UK only. Local Call rate)
NAVIGATION MENU
navigated to the most. The screen will change to show the Route Plan screen (see page 34).
In order to use this option you will need to set your home address first. If you select this option
without setting your home address first, the unit will ask you if you wish to set it now. Alternatively
this can be done using the Set Home Address found in the Settings menu (see page 28).
7 Map Options
Allows you to set the map preferences to your
liking, it allows you to set the way the map looks
and behaves during navigation. When tapped the
screen will change to the Map Options screen,
from where you can easily select several options.
7.1 North Up/Heading Up
Changing this option changes the way the map is
orientated when you are navigating.
North Up – Means that the map will be fixed so that North is upwards. The position icon will be
shown in the centre of the screen and will rotate to show your current direction of travel.
Heading Up – Means that the map will be rotated to always face the direction you are travelling,
while the position icon will be fixed at the lower centre of the screen.
The option with the orange indicator is the currently selected option.
Tap
to confirm the change.
7.2 3D/2D
Changing this options changes the way the map looks when you a driving.
3D – The map will be shown as if you were looking down at it from behind and above your current
position. (When in 3D mode, the option for selecting North Up/Heading Up will be disabled and set
to Heading Up only.)
2D – The map will be shown as if you were looking directly down onto your current position.
The option with the orange indicator is the currently selected option.
Tap
to confirm the change.
Note: You can toggle the map between 2D and 3D modes quickly, by tapping on the compass in
the top right of the navigation screen.
26
Binatone Help Line: 0845 345 9677 (for UK only. Local Call rate)
NAVIGATION MENU
7.3 Motorway Sign Post
When switched on this option does two things. Firstly when driving down major roads and
motorways, it will show information about the approaching junctions. Secondly when you approach
your junction the screen will change to clearly show that this is your junction.
Approaching junctions – While you are currently
navigating a planned route and are on a major road or
motorway, the unit will show you information about
the approaching junctions along the planned route.
You will be shown the distance to the junctions as
well as what the junction sign post will have written on
it.
The unit will also show the action you need to take at
each junction;
The
icon means continue along the current road.
The
icon means to take the junction and exit the current road, In addition to this the sign post
sign will also be shown in orange on the screen.
Required junction – when you reach the junction you
need to take the screen will change to clearly show that
you need to take this junction. You will be shown what
is written on the junction sign.
When switched on the box will be shown with a tick.
Tap
to confirm the change.
7.4 Voice Guidance
This option allows you to activate or deactivate the voice guidance. When deactivated the unit will
no longer give spoken voice directions during navigation.
When activated the box will be shown with a tick.
Tap
27
to confirm the change.
Binatone Help Line: 0845 345 9677 (for UK only. Local Call rate)
NAVIGATION MENU
7.5 Auto Zoom
Allows you to activate or deactivate the auto zoom feature. When auto zoom is activated the unit
will automatically zoom the map during navigation according to your speed, the faster you are
travelling the more the map will zoom out to give you a better view of the road ahead.
When activated the box will be shown with a tick.
7.6 Simulation Speed
This option allows you to change the speed at which a simulation of a route is carried out. You can
set the speed between 50-300 Mph/Kph. For more information on carrying out a simulation of a
route see page 29.
Tap
to confirm the change.
8 Settings
These are the main settings of the unit and allow you to set the unit up to suit your individual
preferences, as well as entering address book entries, setting your home address or activating the
trace record function.
When tapped the screen will change to the settings screen. Note that there is a second page of
options which can be viewed by tapping
Tap
, to return to the previous page of options tap
at any point to return to the previous screen.
8.1 Language
Tap to open the language selection screen. You can
choose from 10 different languages. When a language is
selected not only will it affect the text on the screen, but
will also change the language of the spoken voice
directions.
Tap
or
to scroll back and forth between
each page.
Select the required language so that it is highlighted
orange and tap
28
to confirm. The unit will return to the settings screen.
Binatone Help Line: 0845 345 9677 (for UK only. Local Call rate)
.
NAVIGATION MENU
8.2 Safety Alert
Tap to open the safety alert options screen. From this screen you can set two separate safety
alerts.
Speed camera on – This lets you activate or
deactivate the speed camera warning, when
activated the unit will warn you of an approaching
speed camera visually and shows you the distance
to the camera.
When the option is shown with an orange indicator
it is activated.
Speed alert when exceeding the road speed limit – This lets you activate or deactivate the road
speed limit warning. As well as speed camera locations, the unit contains information about the
speed limit of many roads. When activated the unit will show you the speed limit for the road you
are on with a fixed speed limit icon, if you exceed the speed limit (including any tolerance you
have set) for the road you are on the speed limit icon will flash and the unit will beep.
When the option is shown with an orange indicator it is activated.
When active you can then change the speeding tolerance using the
and
keys to select
the tolerance you would like from 0%, 5%, 10%, 15% and 20%. The unit will then only warn you
when you exceed the speed limit by more than this percentage.
Set the required options and tap
to confirm the unit will then return to the settings screen.
8.3 Trace Record
The unit is capable of logging all positioning information
received from the GPS satellites during navigation. It
then uses this information to draw a track of the route
on the map. This enables you to review the route at a
later time.
If you have previously recorded any trace records these
will be shown in the list. If there are no trace records
you will have to record one first.
Recording a trace record: Use the
button to start the recording process. When active this
button will then change to show
. In this way the key will always show the option which is
currently not selected. It is recommended that you start recording after your route has been
planned or when you are in Free Navigation and you have a valid GPS signal, and you should
stop recording once you have reached your destination. This will prevent the unit from continually
recording while you are not driving and it will also divide each journey into a separate trace record.
Once you have started a trace recording you will need to return back to the map screen.
Note: if you switch the unit off without stopping the trace record function then your trace record for
that journey will be lost.
29
Binatone Help Line: 0845 345 9677 (for UK only. Local Call rate)
NAVIGATION MENU
Each recording will be logged with the following information.
Viewing a trace record: Select the trace record you want to view. The currently selected trace
record will be highlighted orange. Then use the
button to view the trace record on the map.
. The trace record will be shown as a
When active the button will then change to show
slightly opaque orange line with green arrows indicating the direction of travel.
Note: it is only possible to show one trace at a time. A trace record which is been shown will be
shown with a blue highlight on the list. If you select a second Trace and tap
the first trace and begin to show this trace instead.
To delete a trace record, highlight it so that it is orange and tap
, this will cancel
.
8.4 Address Book
Opens the address book screen, from here you
can add, edit, delete and view your address
book locations on the map. You can add address
book entries to the address book so that they
can quickly be used for navigation purposes.
Any previously entered address book entries will
be shown as a list.
8.4.1 Add an Entry
To add an entry to the address book, tap
. You will now be able to add a location using all
of the options available when entering a destination under the Go to section (see page 19).
Once you have added a location to the address
book you can enter further information about that
location. To enter further information tap on the
white box next to the field name, the screen will
change to show a keyboard which allows you to
enter information. Tap
to confirm the entered
at any point to return to the
text. Tap
previous screen.
30
Binatone Help Line: 0845 345 9677 (for UK only. Local Call rate)
NAVIGATION MENU
Name –You can then enter a name for your address book entry; which will be shown in the
address book list. If no name is entered then the address will be automatically entered in this field
and shown as the name.
Address –You can then change the way the address is shown or add further information.
Note: Changing the address does not change the location of the address book entry, just the way
the name is shown.
Tel –You can then enter a telephone number for your address book entry.
Remark – You can then enter a short remark for the location.
Coordinate – This is fixed and shows the co-ordinates for the entered location.
Icon – Tap the
icon, you are then able to select from 10 different icons which are used to
indicate this address book location on the map. Highlight the icon you wish to use and tap
Once you have entered the information and are happy. Tap
to return to the address book list.
Tapping
.
to confirm the entered text and
will return you to the address book screen, but the entry will not be saved.
8.4.2 Edit an Entry
To edit an entry, select the entry so that it is highlighted orange and tap
then be able to change the text and icon for this entry as under the add section.
Tapping
. You will
will return you to the address book screen, but any changes will not be saved.
Note: Changing the address does not change the location of the address book entry, just the way
the name is shown.
8.4.3 Delete an Entry
To delete an entry from the address book, select the entry so that it is highlighted orange and tap
, the entry will be deleted from the address book. Warning: you will not be asked to confirm
the deletion, so make sure that you wish to carry out this operation before tapping.
Tap
31
to return to the settings screen.
Binatone Help Line: 0845 345 9677 (for UK only. Local Call rate)
NAVIGATION MENU
8.5 Day/Night Mode
Allows you to change the map so that the colour and brightness are optimal for driving in either
day time or night time conditions.
There are two options to choose from; manually and automatic.
Manually – when selected allows you to either
simply select day or night mode, by tapping
either
or
to make your selection.
Automatic – When selected allows you to set a start
and end time, when the time is between these two
times the unit will be set to Day mode. At all other
times the unit will automatically switch to Night
mode. You can set a start time of between 1:00 till
12:00 AM and an end time of between 1:00 till
12:00PM. Use the
and
buttons to select
the start and end time. This way you can customise the Day/Night Mode for any time of year.
Once set tap
to confirm the selection and return to the settings screen. Tap
to the settings screen without saving.
to return
8.6 Set Home Address
Allows you to set your home address so that it can be easily used when navigating. When tapped
you will be able to add a location from the options available when entering a destination under the
Go to section (see page 19). Note: the Go Home option will not be available.
If you need to change your home address at a later date, simply tap Set Home Address again to
re-enter your address.
8.7 GPS Status
When tapped the screen will change to the GPS
status screen, Note; this can also be brought up by
from any of the navigation screens.
tapping
This screen shows you information about your
current GPS position. Including the date & time,
your current speed, your current altitude above sea
level and your current position in Longitude and
latitude.
Included with this information is the number of satellites which you are currently locked on to. The
right half of the screen shows the position of these satellites in the sky. Each satellite will be
shown by a coloured circle; Orange means that the unit has locked on to the signal, while grey
means that the satellite has be found but the unit is not currently locked on to its signal. Each
satellite will be identified by a specific number shown inside the circle.
Note: In order to navigate you require that the unit is locked to 4 or more satellites and is referred
to as a 3D fix. The fix status will be shown above the circle on the right- Inactive means not fixed,
active means that a 3D fix has been obtained.
32
Binatone Help Line: 0845 345 9677 (for UK only. Local Call rate)
NAVIGATION MENU
8.8 Miles/Kilometre
Tapping this option will change the units of distance; this
change will be reflected both on the map and in the voice
directions. Tap this option to change between Miles and
Kilometres. The currently selected option will be shown on the
screen.
8.9 About
Tapping this option will show you information relating to the version of navigation software you are
running.
8.10 Time Zone
Allows you to change the time zone so that the
time is always correct for the country you are in
There are two options to choose from; manually
and automatic.
The selected option will be shown with an
orange indicator.
Automatic – When selected the unit will always
set the time zone according to your current GPS
position.
Manually – When selected you can manually set the time zone by using the
select the desired time zone from the list.
and
keys to
In addition to setting either automatic or manually, you can select to have the unit automatically
adjust its self for daylight saving. To activate daylight saving tap in the box so that an orange tick is
shown.
to confirm the selection and return to the settings screen. Tap
Once set tap
to the settings screen without saving.
to return
8.11 Brightness
Allows you to change the brightness of the screen
so as to optimise it for differently lit environments.
Tapping will change the screen to the brightness
setting screen.
There are 5 settings available and are shown as
bars, with an arrow indicating the currently
selected level. Use the
and
keys to set
the required level, the brightness will be reflected
in the screen as the change is made.
Once set tap
to confirm the selection and return to the settings screen. Tap
to the settings screen without saving.
33
Binatone Help Line: 0845 345 9677 (for UK only. Local Call rate)
to return
NAVIGATION MENU
8.12 Calibration
This option allows you to calibrate the screen so that it responds accurately to your screen taps.
You will need this function only if the unit begins to respond inconsistently to your screen taps.
When tapped your will be shown a warning screen, tap
to confirm you would like to
calibrate the screen. The screen will change to the calibration screen; follow the onscreen
instructions in order to complete the calibration process.
9 Route Plan
Once you have entered your destination and
confirmed it is correct, you will be taken to the
Route Plan screen; from here you can begin
navigating, carry out a simulation of the route or
add additional waypoints to the journey.
to return to the Free Navigation
Tap
Menu screen.
Select a destination so that it is highlighted
orange and tap
the map.
to view the location on
9.1 Navigating
To begin navigating to you entered destination tap
. The unit will begin to calculate a route
from your current location to your destination. Once calculated the screen will change to the route
navigation screen and you are ready to drive.
While you are navigating it is still possible to browse the map (see page 19). Note that the unit will
continue to navigate if you are moving, but your position on the map will not be updated and no
voice prompts will be given. Tap
to return or wait for 10 seconds after which the unit will
automatically resume normal navigation.
While the unit is calculating the route you can tap
return back to the Route Plan screen.
at any time to cancel the route and
9.2 Waypoints
You can add up to two additional destinations
before you begin navigating, these additional
destinations are know as waypoints. When the
unit calculates the route it will navigate you to
each waypoint first before continuing on to your
final destination. This is handy if you are
planning a trip were you would like to stop off
on the way to take in sights or simple just for a
break/fuel.
34
Binatone Help Line: 0845 345 9677 (for UK only. Local Call rate)
NAVIGATION MENU
To add waypoints tap
, you will be taken to the Search Menu screen. You can then
enter your waypoint in the same way that you did for your destination (see page 34).
To remove a waypoint/destination, select the desired location so that it is highlighted orange and
then tap
. The waypoint/destination will be removed from the list.
Navigating using waypoints
When the unit calculates the route it will calculate the route from your current position to the
location at the top of the list first, it will then calculate the route from the location at the top of the
list to the location second from top and so on for the next location. The last location on the list will
always be your final destination. You can change the order of a location by selecting it so that it is
highlighted orange, then use the
keys to move it up or down in the list. Once you
have entered all your waypoints and they are in the correct order tap
the route and change to the route navigation screen.
, the unit will calculate
9.3 Simulate
Before you navigate a route for real you can
simulate the route on the unit. To simulate the
route tap
, you will be asked if you would
like to change your starting point. Your current
starting point will be your current position on the
map.
Tap
to change your starting point, you
will be taken to the Search Menu screen. You can
then enter the start point just as if you had entered a destination (see page 20). Once the start
point has been entered the unit will begin calculating the route and then drive the route
automatically.
to keep your current location as the start point, the unit will begin calculating the
Tap
route and then drive the route automatically.
9.4 Route Options
The route options menu allows you to configure
the route to your preference. Tap
the
screen will change to the route options screen.
From here you can enable or disable a number of
options relating to how the route is calculated.
The currently selected options are shown with an
orange indicator.
Use of Motorway - When selected the unit will use motorways in the route calculation.
Use of Ferries When selected the unit will use ferries in the route calculation.
Shortest Route When selected the unit will calculate a route which covers the shortest
distance.
Quickest Route When selected the unit will calculate a route which has the shortest travel
time.
Avoid Toll Roads - When selected the unit will calculate a route which does not use toll roads.
35
Binatone Help Line: 0845 345 9677 (for UK only. Local Call rate)
NAVIGATION MENU
10 Route Navigation Menu
While navigating or simulating a route
tapping the
button will take you to the
Route Navigation Menu. From here you can
obtain detailed information about the route
you have calculated or make changes to the
settings without having to exit navigation.
10.1 Route Plan
This takes you back to the Route Plan Menu
(see page 34). From here you can
will
add/remove waypoints, change the Route Options or even simulate the route. Tapping
result in the route being recalculated from your current position. Any changes will be taken in to
consideration when calculating the route.
10.2 Detour
This option allows you to navigate around any
traffic jams or blocked roads which are along
your planned journey. When tapped the screen
will change to show the available distance
options. You will need to estimate the distance to
the blocked road/traffic jam then choose the
option which is the next lowest distance.
The unit will than calculate a detour route, this
new route can be viewed on the map as a blue
line.
to confirm the new route the unit will return
Tap
to the navigation screen but will now direct you via the
detour route.
Tap
to return to the detour screen, if you were
not happy with the new route and would like to select a
different option or if you no longer want to add a detour.
Tap again from the Detour screen to go back to the
Route Navi Menu screen (see page 36).
10.3 Cancel Route
Tap this option to cancel the route you have planned and stop navigating, you will be returned to
the Free Navi Menu screen.
36
Binatone Help Line: 0845 345 9677 (for UK only. Local Call rate)
NAVIGATION MENU
10.4 Go To
Tapping this option will automatically cancel the route and take you to the Search menu (see page
19). Were you will be able to enter a new destination to navigate too.
10.5 Route Information
Tapping this option will detail the route in text
format and contains useful information about
the route you have planned on a new screen.
As well as showing you your start and
destination locations it will show you the
distance between these two locations as
planned by the unit and the estimated time it
will take to drive the planned route.
Included is a detailed turn by turn explanation
of the route, which includes – the next street name, distance between turns and the turn type.
For example: Turn right onto Redworth Way then drive for 545 yards.
Use the
or
keys to scroll through the list of directions.
If you have added waypoints then the route directions will be split between the different
destination/waypoints points. Each single route is viewed separately and is indicated by
the 2 arrows and 2 numbers separated by a /.
For example: 1/2 shows there are 2 separate routes and you are currently viewing the
first route. Use the
or
keys to change between the different routes, the
information shown will only be for that particular route.
10.6 Map Options
This allows access to the Map options (see page 26).
10.7 Settings
This allows access to the Map options (see page 28).
37
Binatone Help Line: 0845 345 9677 (for UK only. Local Call rate)
FREQUENTLY ASKED QUESTIONS
Frequently asked questions
I can’t find an address.
Please make sure you have correctly spelt your entry. If you do not know how an address is
spelt correctly, simply enter the parts of the address, you know of sure (e.g., “ond”, “Leic” for
Leicester Square in London). Then browse the results list and look for the address. Also make
sure the the city in which you are looking for an address is correct. Sometimes the official
postal address differs from the address you are looking for. In that case, search for a known
address nearby and browse the map.
If you find the address on the map but you cannot find it while searching for it, please let us
know via our help line 0845 345 9677.
The map contains an error / POls are missing.
If you detect an error in the map data (e.g., a street is missing completely), we would like to
inform our map data provider. Please let us know via our help line 0845 345 9677.
I am experiencing problems getting a GPS fix.
If you have problems getting a satellite fix with GPS(you can see how many satellites are
being received by going to the main menu and selecting GPS receiver), please make sure you
are outside and the GPS antenna has good ‘visibility’ to the open sky. Please consult the
hardware manual of your device to get further information on how to obtain a GPS fix.
Where can I get technical support?
Please contact our help line 0845 345 9677.
Where can I get software updates?
Please contact our helpline or your retail store for information about software updates.
Where can I get additional maps and guides?
Please refer to www.binatonegps.com, or contact our help line 0845 345 9677.
38
Binatone Help Line: 0845 345 9677 (for UK only. Local Call rate)
TECHNICAL SPECIFICATIONS
Technical Specifications
CPU
Atlas IV 500 MHz or above
Operating System
Microsoft WinCE.NET 6.0 Core Version
Antenna
I/O
Memory
64MB DDR1 Built-in
Display
4.3″colour TFT touch screen
Weight
0.168 kg
Input Method
Software keyboard
Expansion Slot
SD card
Speaker Built-in
1.0 W loud speaker
USB
USB Client for Active Sync
Battery
Re-chargeable Lithium Polymer battery
Dimension
39
Built-in GPS high sensitivity receiver (64
channels)
119mmx74.5mmx15mm
Binatone Help Line: 0845 345 9677 (for UK only. Local Call rate)
TECHNICAL SPECIFICATIONS
BINATONE TELECOM PLC
1 Apsley Way London NW2 7HF,United Kingdom.
Tel: +44(0) 20 8955 2700 Fax: +44(0) 20 8344 8877
e-mail: binatoneuk@binatonetelecom.co.uk
________________________________________
.
EC Declaration of Conformity
We the manufacturer / Importer :
Binatone Telecom Plc
1 Apsley Way London
NW2 7HF, United Kingdom.
Declare under our sole responsibility that the following product
Type of equipment:
Model Name:
GPS
B430 series
Country of Origin:
Brand:
China
Binatone
complies with the essential protection requirements of Article 3.1 (b) of R&TTE Directive
1999/5/EC and the following standards:
Radio Spectrum:
EMC:
Electrical Safety:
ETS 300487/A1:1997
EN 301489-19 V1.2.1 (2002-11)
EN 301489-1:2008 V1.8.1
EN 60950-1:2001+A11:2004
The product is labelled with the European Approval Marking CE as show. Any Unauthorized
modification of the product voids this Declaration.
Manufacturer / Importer
(signature of authorized person)
Paul Tsui, Product Operation Director
Signature:
40
London,
Place & Date: 23 Feb, 2009
Binatone Help Line: 0845 345 9677 (for UK only. Local Call rate)
Download PDF