Casio | AQW100-1AV | User's Manual | Casio AQW100-1AV User's Manual

MA0804-EA
Operation Guide 5028
Getting Acquainted
Congratulations upon your selection of this CASIO watch. To get the most out of your
purchase, be sure to read this manual carefully and keep it on hand for later reference
when necessary.
Warning!
• The longitude, lunitidal interval, Moon phase indicator and tide graph data that
appear on the display of this watch are not intended for navigation purposes.
Always use proper instruments and resources to obtain data for navigation
purposes.
• This watch is not an instrument for calculating low tide and high tide times. The
tide graph of this watch is intended to provide a reasonable approximation of
tidal movements only.
• CASIO COMPUTER CO., LTD. assumes no responsibility for any loss, or any
claims by third parties that may arise through the use of this watch.
About This Manual
• Button operations are indicated using the letters shown
in the illustration.
• For the sake of simplicity, the sample displays in this
manual do not show the analog hands of the watch.
• Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the “Reference” section.
General Guide
• Press C to change from mode to mode.
• In any mode (except when a setting screen is on the display), press B to illuminate
the face of the watch.
Timekeeping
Mode
Moon/Tide Data
Mode
Press
Stopwatch
Mode
Tide graph
Moon phase
indicator
Hour : Minutes
Seconds
Month – Day
PM indicator
This watch features separate digital and analog
timekeeping. The procedures for setting the digital time
and analog time are different.
• The Moon phase indicator shows the current Moon
phase in accordance with the current date as kept in the
Timekeeping Mode.
• The tide graph shows tidal movements for the current
date in accordance with the current time as kept in the
Timekeeping Mode.
Important!
• Be sure to configure the current time and date, and your
Home Site data (data for the site where you use the
watch) correctly before using the functions of this watch.
See “Home Site Data” for more information.
Use the Timekeeping Mode to set and view a digital display of the current time and date.
When setting the digital time, you can also configure settings for summer time
(Daylight Saving Time or DST).
To set the digital time and date
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press C to move the flashing in the sequence shown
below to select the other settings.
DST
Day
Hour
Month
Minutes
Year
3. When the setting you want to change is flashing, use B and D to change it as
described below.
Screen
36
10:08
2008
6-30
P
Dual Time
Mode
Hand Setting
Mode
Digital Time Daylight Saving Time (DST) Setting
Daylight Saving Time (summer time) advances the digital time setting by one hour
from Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
To toggle the Timekeeping Mode digital time between DST and Standard Time
1. In the Timekeeping Mode, hold down A until the seconds
DST indicator
start to flash, which indicates the setting screen.
2. Press C once to display the DST setting screen.
3. Press D to toggle between Daylight Saving Time (ON
displayed) and Standard Time (OF displayed).
4. Press A twice to exit the setting screen.
• The DST indicator appears on the Timekeeping, Moon/
Tide Data, Alarm, and Hand Setting Mode screens to
indicate that Daylight Saving Time is turned on. In the
case of the Moon/Tide Data Mode, the DST indicator
On/Off status
appears on the tide data screen only.
Home Site Data
Digital Time and Date
Seconds
Alarm
Mode
.
Timekeeping
Day of
week
Countdown Timer
Mode
To do this:
Reset the seconds to 00
Toggle between Daylight Saving Time (ON) and
Standard Time (OF)
Change the hour or minutes
Change the year
Change the month or day
Do this:
Press D.
Press D.
Use D (+) and B (–).
Moon phase, tide graph data, and Moon/Tide Data Mode data will not be displayed
properly unless Home Site data (UTC differential, longitude, and lunitidal interval) is
configured correctly.
• The UTC differential is a value that indicates the time difference between a
reference point in Greenwich, England and the time zone where a city is located.
• The letters “UTC” is the abbreviation for “Coordinated Universal Time”, which is the
world-wide scientific standard of timekeeping. It is based upon carefully maintained
atomic (cesium) clocks that keep time accurately to within microseconds. Leap
seconds are added or subtracted as necessary to keep UTC in sync with the Earth’s
rotation.
• The lunitidal interval is the time elapsing between the Moon’s transit over a meridian
and the next high tide at that meridian. See “Lunitidal Interval” for more information.
• This watch displays lunitidal intervals in terms of hours and minutes.
• The “Site/Lunitidal Interval Data List” at the back of this manual provides UTC
differential and longitude information around the world.
• The following is the initial factory default Home Site data (Tokyo, Japan) when you
first purchase the watch, and whenever you have the batteries replaced. Change
these settings to match the area where you normally use the watch.
UTC differential (+9.0); Longitude (East 140 degrees); Lunitidal interval (5 hours,
20 minutes)
To configure Home Site data
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press A again to display the UTC differential setting
screen.
3. Press C to move the flashing in the sequence shown
below to select other settings.
UTC differential
4. Press A twice to exit the setting screen.
• The first press of A displays the UTC differential setting screen. Pressing A again
exits the setting screen.
• Resetting the seconds only (without changing the DST, hour, or minute setting)
causes the analog minute hand setting to be adjusted automatically.
• See “Digital Time Daylight Saving Time (DST) Setting” below for details about the
DST setting.
• The day of the week is displayed automatically in accordance with the date (year,
month, and day) settings.
UTC
Differential
Longitude
Value
Lunitidal Interval
Minutes
East Longitude/
West Longitude
Lunitidal Interval
Hours
1
Operation Guide 5028
4. When the setting you want to change is flashing, use D and B to change it as
described below.
Setting
UTC Differential
Screen
To specify a date
Longitude Value
East Longitude/
West Longitude
Lunitidal Interval
Hours, Minutes
• When the digital time DST setting is on, the UTC differential can be set in a range
of –11.0 to +15.0 in 0.5-hour units.
5. Press A to exit the setting screen.
To toggle between 12-hour and 24-hour timekeeping
In the Timekeeping Mode, press D to toggle between 12-hour timekeeping and
24-hour timekeeping.
• With the 12-hour format, the P (PM) indicator appears to the left of the hour digits for
times in the range of noon to 11:59 p.m. and the A (AM) indicator appears to the left
of the hour digits for times in the range of midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all other modes.
• The A and P indicators are not displayed with the Timekeeping Mode time on the
Countdown Timer Mode and Dual Time Mode screens.
Setting the Analog Time
Perform the procedure below when the time indicated by the analog hands does not
match the time of the digital display.
1. In the Moon/Tide Data Mode, hold down A until the
year setting starts to flash, which indicates the setting
screen.
2. Press C to move the flashing in the sequence shown
below to select the other settings.
Month – Day
Button Operations
Use D (+) and B (–) to change the setting.
• You can specify a value in the range of –12.0 to +14.0,
in 0.5-hour units.
Use D (+) and B (–) to change the setting.
• You can specify a value in the range of 0° to 180°, in
1-degree units.
Use D to switch between east longitude (E) and west
longitude ( ).
Use D (+) and B (–) to change the setting.
Year
Month
Day
Year
3. While a setting is flashing, use D (+) or B (–) to change it.
• You can specify a date in the range of January 1, 2000 to December 31, 2099.
4. Press A to exit the setting screen.
5. Use A to display either the tide data screen or the Moon data screen.
Stopwatch
1/100 second
Seconds
Minutes
Hours
The stopwatch lets you measure elapsed time, split times,
and two finishes.
• The display range of the stopwatch is 23 hours,
59 minutes, 59.99 seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
• Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C.
To measure times with the stopwatch
To adjust the analog time
1. In the Timekeeping Mode, press C six times to enter
the Hand Setting Mode.
2. Hold down A until the current digital time starts to
flash, which indicates the analog setting mode.
3. Press D to advance the analog time setting by
20 seconds.
• Holding down D advances the analog time setting at
high speed.
Elapsed Time
Start
Stop
Re-start
Stop
Clear
Split
Split release
Stop
Clear
Clear
Split Time
Start
(SPL displayed)
Two Finishes
• If you need to advance the analog time setting a long way, hold down D until the
time starts advancing at high speed, and then press B. This locks the highspeed hand movement, so you can release the two buttons. High-speed hand
movement continues until you press any button. It will also stop automatically
after the time advances 12 hours or if an alarm (multi-function alarm, Hourly Time
Signal, or countdown beeper) starts to sound.
4. Press A to exit the setting mode.
• The watch will automatically adjust the minute hand slightly to match its internal
second count when you exit the setting mode.
• To return to the Timekeeping Mode, press C.
Start
Split
Stop
Split release
First runner
finishes.
Display time of
first runner.
Second runner
finishes.
Display time of
second runner.
Countdown Timer
Timekeeping Mode time
Moon/Tide Data
Moon phase indicator
Tide graph
Time
Moon/tide data lets you view the Moon age and Moon
phase for a particular date, and tidal movements for a
particular date and time at your Home Site.
• If you suspect that the current Moon/tide data is wrong
for some reason, check the current Timekeeping Mode
settings (time, date, and Home Site), and correct them if
required.
• See “Moon Phase Indicator” for information about the
Moon phase indicator and “Tide Graph” for information
about the tide graph.
• All of the operations in this section are performed in the
Moon/Tide Data Mode, which you enter by pressing C.
Year Month – Day
Tide Data Screen
To view the current Moon/Tide Data Mode data
In the Moon/Tide Data Mode, press A to toggle between the tide data screen and the
Moon data screen.
• The tide graph shows the tide for the currently displayed time. The initial tide data
screen shows the level for 6:00 a.m. The Moon data screen shows the Moon age
and Moon phase for the current date.
Tide Data Screen
Moon Data Screen
Moon phase indicator
Tide graph
Year Month – Day
Press
Time
Year Month – Day
.
Seconds
Minutes
Hours
To use the countdown timer
Press D while in the Countdown Timer Mode to start the countdown timer.
• When the end of the countdown is reached and auto-repeat is turned off, the alarm
sounds for 10 seconds or until you stop it by pressing any button. The countdown
time is automatically reset to its starting value after the alarm stops.
• When auto-repeat is turned on, the countdown will restart automatically without
pausing when it reaches zero. The alarm sounds in order to signal when the
countdown reaches zero.
• The countdown timer measurement operation continues even if you exit the
Countdown Timer Mode.
• Press D while a countdown operation is in progress to pause it. Press D again to
resume the countdown.
• To completely stop a countdown operation, first pause it (by pressing D), and then
press A. This returns the countdown time to its starting value.
To set up the countdown timer
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A until the hour
setting of the countdown start time starts to flash, which
indicates the setting screen.
• If the countdown start time is not displayed, use the
procedure under “To use the countdown timer” to
display it.
2. Press C to move the flashing in the sequence shown
below to select other settings.
Hours
Moon age
• While the tide data screen is displayed, press D to advance to the next hour.
• While the Moon data screen is displayed, press D to advance to the next day.
• You can also specify a particular date (year, month, day) to view its tide data and
Moon data. See “To specify a date” for more information.
• When you enter the Moon/Tide Data Mode, the screen (tide data or Moon data) that
was displayed the last time you exited the mode appears first.
You can set the countdown timer within a range of
one minute to 24 hours. An alarm sounds when the
countdown reaches zero.
• You can also select auto-repeat, which automatically
restarts the countdown from the original value you set
whenever zero is reached.
• All of the operations is this section are performed in the
Countdown Timer Mode, which you can enter using C.
Minutes
Auto-repeat
3. While a setting is flashing, use D and B to change it as described below.
Screen
To do this:
Do this:
0:00
Change the hours or minutes
Use D (+) and B (–).
Toggle auto-repeat on (ON) and off (OF)
Press D.
• To specify a countdown start time of 24 hours, set 0:00.
4. Press A to exit the setting screen.
• The auto-repeat on indicator ( ) is displayed on the Countdown Timer Mode
screen while this function is turned on.
• Frequent use of auto-repeat and the alarm can run down batteries power.
2
Operation Guide 5028
Alarms
Alarm date
(Month – Day)
Alarm time
(Hour : Minutes)
Alarm number
You can set up to three independent multi-function alarms
with hour, minutes, month, and day. When an alarm is
turned on, the alarm tone sounds when the alarm time is
reached. One of the alarms can be configured as a
snooze alarm or a one-time alarm, while the other two are
one-time alarms.
You can also turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour.
• There are three alarms numbered1 through 3. You can
configure Alarm1 as a snooze alarm or a one-time
alarm. Alarms 2 and 3 can be used as one-time alarms
only.
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C.
• SNZ indicator flashes during the 5-minute intervals between alarms.
• Displaying the Alarm1 setting screen while the snooze alarm is turned on
automatically turns off the snooze alarm (making Alarm1 a one-time alarm).
Dual Time
DST indicator
Timekeeping
Mode time
Alarm Types
The alarm type is determined by the settings you make, as described below.
• Daily alarm
Set the hour and minutes for the alarm time. This type of setting causes the alarm to
sound everyday at the time you set.
• Date alarm
Set the month, day, hour and minutes for the alarm time. This type of setting causes
the alarm to sound at the specific time, on the specific date you set.
• 1-Month alarm
Set the month, hour and minutes for the alarm time. This type of setting causes the
alarm to sound everyday at time you set, only during the month you set.
• Monthly alarm
Set the day, hour and minutes for the alarm time. This type of setting causes the alarm
to sound every month at the time you set, on the day you set.
To set an alarm time
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
Dual time
(Hour : Minutes)
The Dual Time Mode lets you keep track of time in a
different time zone. You can select Standard Time or
Daylight Saving Time for the Dual Time Mode time.
• In the Dual Time Mode, the seconds count is
synchronized with the seconds count of the current
digital time.
To set the Dual Time
1. Press C to enter the Dual Time Mode.
2. In the Dual Time Mode, hold down A until the DST
setting starts to flash, which indicates the setting
screen.
3. Press C to move the flashing in the sequence shown
below to select the other setttings.
DST
Hour
Minutes
4. When the setting you want to change is flashing, use B and D to change it as
described below.
Screen
A
8:08
To do this:
Toggle between Daylight Saving Time (ON) and
Standard Time (OF)
Change the hour or minutes
Do this:
Press D.
Use D (+) and B (–).
5. Press A to exit the setting screen.
• The DST indicator on the Dual Time Mode screen indicates that DST is turned on for
the Dual Time Mode time.
Illumination
This watch has an EL (electro-luminescent) panel that
causes the entire display to glow for easy reading in the
dark.
• See “Illumination Precautions” for more important
information.
• To set a one-time alarm, display one of the screens
indicated by alarm number 2 or 3. To set the snooze
alarm, display the screen indicated by1.
2. After you select an alarm, hold down A until the hour
setting of the alarm time starts to flash, which indicates
the setting screen.
• This operation automatically turns on the alarm.
To illuminate the face of the watch
In any mode (except when a setting screen is on the
display), press B to illuminate the face of the watch.
• You can use the procedure below to select either
1.5 seconds or 3 seconds as the illumination duration.
When you press B, the illumination will remain on for
about 1.5 seconds or 3 seconds, depending on the
current illumination duration setting.
3. Press C to move the flashing in the sequence shown below to select other
settings.
Hour
Minutes
Month
Day
4. While a setting is flashing, use D (+) and B (–) to change it.
• To set an alarm that does not include a month (daily alarm, monthly alarm),
set x for the month. Use D and B until the x mark appears (between 12 and 1)
while month setting is flashing.
• To set an alarm that does not include a day (daily alarm, 1-month alarm),
set xx for the day. Use D and B until the xx mark appears (between the end
of the month and 1) while the day setting is flashing.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (A indicator) or p.m. (P indicator).
5. Press A to exit the setting screen.
To specify the illumination duration
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. While the seconds are flashing, press B to toggle the
illumination duration between 1.5 seconds (x) and 3
seconds ( ).
3. Press A twice to exit the setting screen.
Alarm Operation
Reference
The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, until you turn the alarm off or change it to a onetime alarm.
• To stop the alarm tone after it starts to sound, press any button.
• Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen
Displaying the alarm1 setting screen
To turn Alarms 2 and 3, and the Hourly Time Signal on and off
1. In the Alarm Mode, use D to select a one-time alarm
(alarm number 2 or 3) or the Hourly Time Signal (:00).
2. Press A to toggle it on and off.
• Turning on a one-time alarm (2 or 3) displays the alarm
on indicator on its screen.
• Turning on the Hourly Time Signal displays the hourly
time signal on indicator.
• The alarm on (ALM) indicator and Hourly time Signal on
(SIG) indicator are displayed in all modes.
Alarm on indicator
Hourly time signal on
indicator
To select the operation of Alarm1
1. In the Alarm Mode, use D to select Alarm1.
2. Press A to cycle through the available settings in the sequence shown below.
Snooze
alarm on
Moon Phase Indicator
The Moon phase indicator of this watch indicates the current phase of the Moon as
shown below.
(part you cannot see)
Moon phase (part you can see)
Moon Phase
Indicator
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
Alarm on
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
Moon Age
Moon Phase
0.0 - 1.8
27.7 - 29.5 1.9 - 5.5 5.6 - 9.2 9.3 - 12.9 13.0-16.6 16.7- 20.2
New
First
Full
Moon
Quarter
Moon
(Waxing)
20.3-23.9 24.0-27.6
Last
Quarter
(Waning)
• The Moon phase indicator shows the Moon as viewed at noon from a position in the
Northern Hemisphere looking south. Note that at times the image shown by the
Moon phase indicator may differ from that of the actual Moon in your area.
• The left-right orientation of the Moon phase is reversed when viewing from the
Southern Hemisphere or from a point near the equator.
Moon Phases and Moon Age
The Moon goes through a regular 29.53-day cycle. During each cycle, the Moon
appears to wax and wane as the relative positioning of the Earth, Moon, and Sun
changes. The greater the angular distance between the Moon and the Sun,* the more
we see illuminated.
* The angle to the Moon in relation to the direction at which the Sun is visible from the
Earth.
This watch performs a rough calculation of the current Moon age starting from day 0
of the moon age cycle. Since this watch performs calculations using integer values
only (no fractions), the margin for error of the displayed Moon age is ±1 day.
Alarm off
• The applicable alarm on indicator (SNZ ALM) is displayed in all modes when an
alarm is turned on.
3
Operation Guide 5028
Tide Graph
Site/Lunitidal Interval Data List
The Tide Graph has six graphic segments, each of which indicates a different tide
level. The current tide level is indicated by the displayed graphic segment.
(Rising Tide)
H
L
High Tide
Low Tide
(Falling Tide)
(Rising Tide)
Tidal Movements
Tides are the periodic rise and fall of the water of oceans, seas, bays, and other
bodies of water caused mainly by the gravitational interactions between the Earth,
Moon and Sun. Tides rise and fall about every six hours. The tide graph of this watch
indicates tidal movement based on the Moon’s transit over a meridian and the lunitidal
interval. The lunitidal interval differs according to your current location, so you must
specify a lunitidal interval in order to obtain the correct tide graph readings.
• The tide graph displayed by this watch is based on the current Moon age.
Remember that the margin for error of the Moon age displayed by this watch is ±1
day. The greater the error in a particular Moon age, the greater the error in the
resulting tide graph.
Lunitidal Interval
Theoretically, high tide is at the Moon’s transit over the meridian and low tide is about
six hours later. Actual high tide occurs somewhat later, due to factors such as
viscosity, friction, and underwater topography. Both the time differential between the
Moon’s transit over the meridian until high tide and the time differential between the
Moon’s transit over the meridian until low tide are known as the “lunitidal interval”.
When setting the lunitidal interval for this watch, use the time differential between the
Moon’s transit over the meridian until high tide.
Button Operation Tone
The button operation tone sounds any time you press one
of the watch’s buttons. You can turn the button operation
tone on or off as desired.
• Even if you turn off the button operation tone, the alarm,
Hourly Time Signal, and Countdown Timer Mode alarm
all operate normally.
Site
Anchorage
Bahamas
Baja, California
Bangkok
Boston
Buenos Aires
Casablanca
Christmas Island
Dakar
Gold Coast
Great Barrier Reef, Cairns
Guam
Hamburg
Hong Kong
Honolulu
Jakarta
Jeddah
Karachi
Kona, Hawaii
Lima
Lisbon
London
Los Angeles
Maldives
Manila
Mauritius
Melbourne
Miami
Noumea
Pago Pago
Palau
Panama City
Papeete
Rio De Janeiro
Seattle
Shanghai
Singapore
Sydney
Tokyo
Vancouver
Wellington
UTC Differential
Standard
DST/
Time
Summer Time
–9.0
–8.0
–5.0
–4.0
–7.0
–6.0
+7.0
+8.0
–5.0
–4.0
–3.0
–2.0
+0.0
+1.0
+14.0
+15.0
+0.0
+1.0
+10.0
+11.0
+10.0
+11.0
+10.0
+11.0
+1.0
+2.0
+8.0
+9.0
–10.0
–9.0
+7.0
+8.0
+3.0
+4.0
+5.0
+6.0
–10.0
–9.0
–5.0
–4.0
+0.0
+1.0
+0.0
+1.0
–8.0
–7.0
+5.0
+6.0
+8.0
+9.0
+4.0
+5.0
+10.0
+11.0
–5.0
–4.0
+11.0
+12.0
–11.0
–10.0
+9.0
+10.0
–5.0
–4.0
–10.0
–9.0
–3.0
–2.0
–8.0
–7.0
+8.0
+9.0
+8.0
+9.0
+10.0
+11.0
+9.0
+10.0
–8.0
–7.0
+12.0
+13.0
Longitude
Lunitidal
Interval
149°W
77°W
110°W
101°E
71°W
58°W
8°W
158°W
17°W
154°E
146°E
145°E
10°E
114°E
158°W
107°E
39°E
67°E
156°W
77°W
9°W
0°E
118°W
74°E
121°E
57°E
145°E
80°W
166°E
171°W
135°E
80°W
150°W
43°W
122°W
121°E
104°E
151°E
140°E
123°W
175°E
5:40
7:30
8:40
4:40
11:20
6:00
1:30
4:00
7:40
8:30
9:40
7:40
4:50
9:10
3:40
0:00
6:30
10:10
4:00
5:20
2:00
1:10
9:20
0:10
10:30
0:50
2:10
7:30
8:30
6:40
7:30
3:00
0:10
3:10
4:20
1:20
10:20
8:40
5:20
5:10
4:50
*Based on data as of 2003.
To turn the button operation tone on and off
In any mode (except when a setting screen is on the display), hold down C to toggle
the button operation tone on ( not displayed) and off ( displayed).
• Holding down C to turn the button operation tone on or off also causes the watch’s
current mode to change.
• The
indicator is displayed in all modes when the button operation tone is turned
off.
Auto Return Features
• If you leave a screen with flashing digits on the display for two or three minutes
without performing any operation, the watch automatically exits the setting screen.
• If you leave the watch in the Moon/Tide Data, Alarm or Hand Setting Mode for two or
three minutes without performing any operation, it automatically changes to the
Timekeeping Mode.
Scrolling
The B and D buttons are used in various modes and setting screens to scroll
through data on the display. In most cases, holding down these buttons during a scroll
operation scrolls through the data at high speed.
Timekeeping
• Resetting the seconds to 00 while the current count is in the range of 30 to 59
causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are
reset to 00 without changing the minutes.
• The year can be set in the range of 2000 to 2099.
• The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to change
it except after you have the watch’s batteries replaced.
Illumination Precautions
• Illumination may be hard to see when viewed under direct sunlight.
• Illumination automatically turns off whenever an alarm sounds.
• Frequent use of illumination runs down the batteries.
4
Download PDF

advertising