Casio | AQW101-1AV | User's Manual | Casio AQW101-1AV User's Manual

MO0905-EA
Operation Guide 5056
Getting Acquainted
Congratulations upon your selection of this CASIO watch. To get the most out of your
purchase, be sure to read this manual carefully.
Warning!
• The measurement functions built into this watch are not intended for use in taking
measurements that require professional or industrial precision. Values produced
by this watch should be considered as reasonably accurate representations only.
• When fishing, always take proper precautions to ensure your own personal safety
and the personal safety of others around you.
• The fishing level indicator and moon phase indicator produced by this watch are
all based on calculations that use the watch’s current time, date, and Home Site
settings. Because of this, you should make sure that the current date and time,
and your Home Site data are all correct before using the indicators.
Warning!
• See the “Timekeeping” section of this manual for information about setting the
current time and date, and about specifying your Home Site.
• Note that the fishing level indicator and moon phase indicator are all based on
calculated values. They are provided only for reference purposes.
Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any damage
or loss suffered by you or any third party arising through the use of this product or
its malfunction.
About This Manual
• Button operations are indicated using the letters shown
in the illustration.
• For the sake of simplicity, the sample displays in this
manual do not show the analog hands of the watch.
• Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the “Reference” section.
(Light)
General Guide
Temperature Data
Recall Mode
• Press C to change from mode to mode.
• In any mode (except when a setting screen is on the display), press B to illuminate
the display.
Fishing Mode
Stopwatch Mode
▲
▲
World Time Mode
▲
Press C.
▲
Timekeeping Mode
Countdown Timer
Mode
Alarm Mode
▲
▲
▲
▲
Hand Setting Mode
Timekeeping
Use the Timekeeping Mode to set and view the current time and date.
This watch features separate digital and analog timekeeping. The procedures for
setting the digital time and analog time are different.
• In the Timekeeping Mode, press A to toggle between the thermometer screen and
the temperature tendency screen.
Temperature Tendency
Thermometer Screen
Screen
Temperature
Moon phase
indicator
Day of
week –
Day
▲
Seconds
Fishing level
indicator
Important!
• Be sure to configure the current time and date, and your Home Site data (data for
the site where you use the watch) correctly before using the functions of this watch.
See “Home Site Data” for more information.
Setting the Digital Time and Date
This watch is preset with UTC differential values that represent each time zone around
the globe. Before setting the digital time, be sure to first set the UTC differential for
your Home Site, which is the location where you normally will be using the watch.
• Note that World Time Mode times are all displayed based on the time and date
settings you configure in the Timekeeping Mode.
lll
Press D.
Change the hour or minutes
Use D (+) and B (–).
Use D (+) and B (–).
Daylight Saving Time (DST) Setting
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
To toggle the Timekeeping Mode digital time between DST and Standard Time
1. In the Timekeeping Mode, hold down A until the
On/Off status
seconds start to flash, which indicates the setting
screen.
2.
Press C once and the DST setting screen appears.
l ll
3. Press D to toggle between Daylight Saving Time (ON
displayed) and Standard Time (OF displayed).
lll
4. Press A twice to exit the setting screen.
• The DST indicator appears on the Timekeeping, Fishing,
Alarm, and Hand Setting Mode screens to indicate that
DST indicator
Daylight Saving Time is turned on. In the case of the
Fishing Mode, the DST indicator appears on the fishing
level screen only.
lll
ll
To set the digital time and date
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
• Be sure to configure the correct UTC differential for
l ll
your Home Site before configuring any other
Timekeeping Mode settings.
• See the “City Code List” for information about the UTC
differential settings that are supported.
2. Press C to move the flashing in the sequence shown
Seconds
below to select the setting you want.
lll
Toggle between Daylight Saving
Time (ON) and Standard Time (OF)
Specify the UTC differential
• The UTC differential setting range is –12.0 to +14.0 in 0.5-hour units for Standard
Time (DST turned off), and –11.0 to +15.0 in 0.5-hour units for summer time (DST
turned on).
• For information about settings other than the time and date, see the following.
Temperature Sensor Calibration: “Thermometer”
Temperature Unit: “To specify the temperature display unit”
4. Press A twice to exit the setting screen.
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all modes.
• The day of the week is displayed automatically in accordance with the date (year,
month, and day) settings.
• See “Daylight Saving Time (DST) Setting” below for details about the DST setting.
• Any time the seconds setting is changed, the analog hands are adjusted accordingly.
lll
• The fishing level indicator indicates the times when fish can be expected to be feeding.
For more information, see “Fishing Mode”.
• The Moon phase indicator shows the current Moon phase in accordance with the
current date as kept in the Timekeeping Mode.
• See “Thermometer” for details about the thermometer screen and temperature
tendency graph.
ll
Hour : Minutes
Do this:
Press D.
Toggle between 12-hour (12H) and Press D.
24-hour (24H) timekeeping
Use D (+) and B (–).
Change the year, month, or day
ll
PM
indicator
To do this:
Reset the seconds to 00
Screen:
Temperature
tendency
graph
Press A.
▲
3. When the setting you want to change is flashing, use D and B to change it as
described below.
ll
lll
Seconds
Temperature
Unit
DST
UTC
Differential
Temperature Sensor
Calibration
Hour
Day
Minutes
Month
12/24-Hour
Format
Year
Home Site Data
Moon phase, the fishing level indicator, and Fishing Mode data will not be displayed
properly unless Home Site data (UTC differential and longitude) is configured
correctly.
• The UTC differential is a value that indicates the time difference between a
reference point in Greenwich, England and the time zone where a city is located.
• The letters UTC is the abbreviation for Coordinated Universal Time, which is the
world-wide scientific standard of timekeeping. It is based upon carefully maintained
atomic (cesium) clocks that keep time accurately to within microseconds. Leap
seconds are added or subtracted as necessary to keep UTC in sync with the Earth’s
rotation.
1
Operation Guide 5056
Longitude Unit
(East/West)
Use D to switch between east longitude ( )
and west longitude ( ).
6. Press A to exit the setting screen.
Setting the Analog Time
Perform the procedure below when the time indicated by the analog hands does not
match the time of the digital display.
lll l ll
Fishing Level Screen
Fishing Level Indicator
The fishing level indicator shows the relative favorability of a fishing time (calculated in
accordance with Moon transit and phase) as shown in the table below.
Level 4
Moon Transit
Other
Month
Day
Year
3. While a setting is flashing, use D (+) or B (–) to change it.
• You can specify a date in the range of January 1, 2000 to December 31, 2099.
4. Press A to exit the setting screen.
5. Use A to display either the fishing level screen or the Moon Data screen.
Level 3
Level 2
Level 1
Upper
Lower
West
East
Other
Level 5
Level 4
Level 3
Level 4
Level 3
Level 2
Level 3
Level 2
Level 1
* These indicators actually appear during Moon ages 13.0 to 16.6 (Full Moon and
phase immediately preceding it) and 27.7 to 1.8 (New Moon and phase immediately
preceding it).
• The fishing level indicator changes in accordance with the Moon data.
• In the Timekeeping Mode, the FISH indicator flashes whenever the fishing level of
the current time is 4 or 5.
To view the current fishing level and Moon data
In the Fishing Mode, press A to toggle between the fishing level screen and the
Moon Data screen.
• The fishing level indicator shows the level for the displayed time. The initial fishing
level screen shows the level for 6:00 a.m. The Moon data screen shows the Moon
age and Moon phase for the current date.
This watch uses a temperature sensor to measure temperature. A reading is taken
during each even-numbered minute, and the result of the last reading is displayed on
the thermometer screen.
The watch also takes separate readings and stores them in memory for display in the
temperature tendency graph, which can be viewed in the Timekeeping Mode.
Measured temperature values are stored in memory for later recall when you need
them.
Temperature
Thermometer Screen
Tendency Screen Temperature
Temperature
Press A.
tendency
graph
▲
The Fishing Mode displays an indicator that shows, as
one of five levels, the suitability of a specific date and time
(minute 00 to minute 59 of a particular hour) for fishing.
This mode also can be used to display Moon Data (Moon
age and Moon phase) for a specific date.
• If you suspect that the fishing level indicator or current
Moon data is wrong for some reason, check the current
Timekeeping Mode settings (time, date, and Home Site),
and correct them if required.
• See “Moon Phase Indicator” for information about the
Moon phase indicator.
• All of the operations in this section are performed in the
FISH
Fishing Mode, which you enter by pressing C.
indicator
Month – Day Moon phase
indicator
Moon Phase
New moon*
Full moon
First quarter
Last quarter
Year
▲
ll
ll
Fishing Mode
Level 5
lll lll
• You can select either Celsius (°C) or Fahrenheit (°F) units for the thermometer
screen. See “To specify the temperature display unit” for more information.
• The thermometer screen displays temperature values in 0.1°C units (or 0.2°F units).
• The display range of the thermometer screen is –10.0°C to 60.0°C (or 14.0°F to
140.0°F).
• You can calibrate the temperature sensor if you feel that the displayed temperature
values are not correct. See “Temperature Sensor Calibration” for more information.
Important!
• Temperature measurements are affected by your body temperature (while you are
wearing the watch), direct sunlight, and moisture. To achieve a more accurate
temperature measurement, remove the watch from your wrist, place it in a well
ventilated location out of direct sunlight, and wipe all moisture from the case. It takes
approximately 20 to 30 minutes for the case of the watch to reach the actual
surrounding temperature.
Temperature Tendency Graph
The watch also takes temperature readings at the top and the bottom of each hour
and stores the results in memory for display on the temperature tendency graph.
Depending on the current Timekeeping Mode time, the temperature tendency graph
shows either the top of the hour measurements or the bottom of the hour
measurements for the past 17 hours.
From the top of each hour to the 29th minute, past top of the hour readings are shown
in the graph. From the bottom of each hour to the 59th minute, past bottom of the hour
readings are shown in the graph.
Temperature tendency graph contents are updated every 30 minutes.
+6.0 to +9.9°C (+10.8 to +17.8°F)
+2.0 to +5.9°C (+3.6 to +10.6°F)
–1.9 to +1.9°C (–3.4 to +3.4°F)
–5.9 to –2.0°C (–10.6 to –3.6°F)
–9.9 to –6.0°C (–17.8 to –10.8°F)
▲
1. In the Timekeeping Mode, press C seven times to
enter the Hand Setting Mode.
2. Hold down A until the current digital time starts to
flash, which indicates the setting screen.
3. Use D to adjust the analog setting.
• Press D once to advance the hands 20 seconds.
• Hold down D to advance the hands at high speed.
• To lock high speed hands movement, hold down D to start it and then press B
to lock. The hands will continue to advance for one 12-hour cycle or until you
press any button to stop it.
It will also stop automatically after the time advances 12 hours or if an alarm (daily
alarm, Hourly Time Signal, or countdown beeper) starts to sound.
4. Press A to exit the setting screen.
• The minute hand will be adjusted slightly to match the seconds when you exit the
setting screen.
• To return to the Timekeeping Mode, press C.
Time
1. In the Fishing Mode, hold down A until the year setting
starts to flash, which indicates the setting screen.
2. Press C to move the flashing in the sequence shown
below to select the other settings.
Thermometer
To adjust the analog time
Fishing level
indicator
To specify a date
ll
Use D (+) and B (–) to change the setting.
• You can specify a value from 0° to 180°, in 1degree units.
Moon age
Fishing level
indicator
Time
• While the fishing level screen is displayed, press D to advance to the next hour.
• While the Moon Data screen is displayed, press D to advance to the next day.
• You can also specify a particular date (year, month, day) to view its fishing level and
Moon data. See “To specify a date” for more information.
• When you enter the Fishing Mode, the screen (fishing level or Moon data) that was
displayed the last time you exited the mode appears first.
Month – Day
Button Operations
Longitude Value
lll lll
Press A.
ll
Screen
Moon phase
indicator
lll l ll
ll
lll l ll
Setting
Moon Data Screen
Month – Day
Month – Day
▲
ll
To configure Home Site data
1. In the Timekeeping Mode, hold down A until the
Longitude
seconds start to flash, which indicates the setting
(east/west)
screen.
2. Press C twice to display the UTC differential setting
screen, and confirm that the setting is correct.
• If the UTC differential setting is not correct, use
D (+) and B (–) to change it.
l
l
l
l
l
l
3. Press A to display the longitude value setting screen.
4. Press C to toggle the flashing between the longitude
value and the longitude unit (east/west).
5. While the setting you want to change is flashing, use
Longitude
D and B to change it as described below.
value
Fishing Level Screen
▲
• The “Site Data List” provides UTC differential and longitude information around the
world.
• The following is the initial factory default Home Site data (Tokyo, Japan) when you
first purchase the watch and whenever you have the batteries replaced. Change
these settings to match the area where you normally use the watch.
UTC differential (+9.0); Longitude (East 140 degrees)
Past 17 hours of
measurement values
Latest measurement
value
The horizontal axis of the graph represents time. The rightmost column is the newest
temperature value in memory, while the leftmost column is the temperature value
stored approximately 17 hours ago (1 dot = 1 hour). The vertical axis of the graph
represents the relative change from one hour to the next.
• When the relative change from one hour to the next exceeds +10.0°C (+18.0°F), the
dot at the highest point for the applicable hour flashes.
• When the relative change from one hour to the next exceeds –10.0°C (–18.0°F),
there is no dot in the applicable hour’s column.
• If a measurement error occurs for some reason, only a single the dot in the center
column will be displayed.
Temperature change greater
than +10.0°C (+18.0°F)
Temperature change greater
than –10.0°C (–18.0°F)
Error
2
Operation Guide 5056
Recalling Temperature Data
The measurements the watch takes at the top and the bottom of each hour are stored
in memory automatically. Memory can hold up to 50 measurement records. You can
use the Temperature Data Recall Mode to recall memory data when you need it.
• Each temperature data record has a number. The newest data record is number 01,
while the oldest data record is the one with the highest number.
• When there are already 50 records in memory, storage of a new temperature
reading causes the oldest record (record number 50) to be deleted automatically to
make room for the new data. The new data is assigned record number 1, and all of
the numbers of all the other records (01 to 49) are incremented by 1 (becoming 02
through 50).
To recall temperature records
1. In the Timekeeping Mode, press C twice to enter the
Temperature
Temperature Data Recall Mode.
• This displays the newest record currently in memory.
2. Use D (+) to scroll through the records.
• Pressing D while the oldest record is displayed will
scroll to the newest record.
• If a temperature measurement operation is performed
while a record is displayed, the displayed record’s
number will be incremented by 1.
• If an error occurs during temperature measurement,
‘‘--.-’’ will be shown for the temperature value in the
corresponding record.
Data storage time
Record number
➤D
Stop
➤D
Re-start
➤D
Stop
➤A
Clear
➤A
Split
➤A
Split release
➤D
Stop
➤A
Clear
➤D
Stop
➤A
Split release
➤A
Clear
Split Time
Start
(SPL displayed)
➤A
Split
Start
First runner
finishes.
Display time of
first runner.
Second runner
finishes.
Display time of
second runner.
Seconds
Minutes
lll
To configure countdown start time and auto-repeat settings
1. While the countdown start time is on the display in the
Auto-repeat on indicator
Countdown Timer Mode, hold down A until the hour
setting of the countdown start time starts to flash, which
indicates the setting screen.
• If the countdown start time is not displayed, use the
procedure under “To use the countdown timer” to
l
l
l
display it.
2. Press C to move the flashing in the sequence shown
below, and select the setting you want to change.
lll
lll
To turn the Daily alarm and the Hourly Time Signal on and off
In the Alarm Mode, press D to cycle through the settings shown below.
Alarm On
Signal Off
Alarm Off
Signal On
Alarm On
Signal On
• The alarm on indicator and the Hourly Time Signal on indicator are shown on the
display in all modes while these functions are turned on.
The World Time Mode digitally displays the current time in
50 cities (30 time zones) around the world.
• The times kept in the World Time Mode are
synchronized with the time being kept in the
Timekeeping Mode. If you feel that there is an error in
any World Time Mode time, check the UTC differential of
your Home Site Data (Home City) and the current
setting of the Timekeeping Mode time.
• Select a city code in the World Time Mode to display the
current time in any particular time zone around the
globe. See the “City Code List” for information about the
Current time in
selected city
UTC differential settings that are supported.
• All of the operations in this section are performed in the
Day of week and day in
World Time Mode, which you enter by pressing C.
selected city
City code
You can set the countdown timer within a range of one
minute to 100 hours. An alarm sounds when the
countdown reaches zero.
• You can also select auto-repeat, which automatically
restarts the countdown from the original value you set
whenever zero is reached.
• All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C.
To use the countdown timer
Press D while in the Countdown Timer Mode to start the countdown timer.
• When the end of the countdown is reached and auto-repeat is turned off, the alarm
sounds for 10 seconds or until you stop it by pressing any button. The countdown
time is automatically reset to its starting value after the alarm stops.
• When auto-repeat is turned on, the countdown will restart automatically without
pausing when it reaches zero. The alarm sounds to signal when the countdown
reaches zero.
• The countdown timer measurement operation continues even if you exit the
Countdown Timer Mode.
• To stop a countdown operation completely, first pause it (by pressing D), and then
press A. This returns the countdown time to its starting value.
On/Off status
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
World Time
Countdown Timer
Hours
1. In the Alarm Mode, hold down A until the hour setting
of the alarm time starts to flash, which indicates the
setting screen.
• This operation turns on the alarm automatically.
l ll
2. Press C to move the flashing between the hour and
minute settings.
3. While a setting is flashing, use D (+) and B (–) to
change it.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (A indicator) or p.m. (P indicator).
4. Press A to exit the setting screen.
Alarm Off
Signal Off
Two Finishes
D
Hourly time signal
on indicator
The alarm sounds at the preset time for 10 seconds, regardless of the mode the watch is in.
• To stop the alarm tone after it starts to sound, press any button.
Elapsed Time
D
Time Signal, which will cause the watch to beep twice
every hour on the hour.
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C.
Alarm Operation
Minutes
Start
Alarm on
indicator
ll
Seconds
The stopwatch lets you measure elapsed time, split times,
and two finishes.
• The display range of the stopwatch is 99 hours, 59
minutes, 59.99 seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C.
To measure times with the stopwatch
D
Alarm time
While the alarm is turned on, the watch beeps when the
(Hour : Minutes) alarm time is reached. You can also turn on an Hourly
AM indicator
lll
Hours
Alarm
To set the alarm time
Stopwatch
1/100 second
3. Perform the following operations, depending on which setting is currently selected
on the display.
• While the start time setting is flashing, use D (+) and B (–) to change it.
• Set 0:00 to specify 100 hours.
• While the auto-repeat on/off setting (0N or 0F) is flashing on the display, press
D to toggle auto-repeat on (0N) and off (0F).
4. Press A to exit the setting screen.
• The auto-repeat on indicator ( ) is displayed on the Countdown Timer Mode
screen while this function is turned on.
• Frequent use of auto-repeat and the alarm can run down battery power.
Start Time
(Hours)
Start Time
(Minutes)
Auto-Repeat
On/Off
To view the time in another city
While in the World Time Mode, press D to scroll eastward through the city codes
(time zones).
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, use D to display the city code
(time zone) whose Standard Time/Daylight Saving Time
setting you want to change.
2. Hold down A to toggle between Daylight Saving Time
(DST indicator displayed) and Standard Time (DST
indicator not displayed).
• The DST indicator is shown on the World Time screen
while Daylight Saving Time is turned on.
DST indicator
• Note that changing the Daylight Saving Time for any city
code causes the setting to be applied to all city codes.
Illumination
This watch has an EL (electro-luminescent) panel that
causes the entire display to glow for easy reading in the
dark.
• See “Illumination Precautions” for other important
information about using illumination.
To turn on illumination
In any mode (except when a setting screen is on the
display), press B to illuminate the display for about one
second.
3
ll
Operation Guide 5056
Reference
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
Moon Phase Indicator
The Moon phase indicator of this watch indicates the current phase of the Moon as
shown below.
Moon phase indicator
Auto Return Feature
• If you leave a screen with flashing digits on the display without performing any
operation for two or three minutes, the watch saves any settings you have made up
to that point and exits the setting screen automatically.
• The watch will change to the Timekeeping Mode automatically if you do not perform
any operation in the Fishing Mode, Temperature Data Recall Mode, Alarm Mode, or
Hand Setting Mode for two or three minutes.
Scrolling
The B and D buttons are used in various modes and setting screens to scroll
through data on the display. In most cases, holding down these buttons during a scroll
operation scrolls through the data at high speed.
Timekeeping
(part you cannot see)
Moon phase (part you can see)
Moon
Phase
Indicator
Moon Age
0.0 - 1.8 1.9 - 5.5 5.6 - 9.2 9.3 - 12.9 13.0 - 16.6 16.7 - 20.2 20.3 - 23.9 24.0 - 27.6
27.7 - 29.5
Moon Phase
New
Moon
First
Quarter
(Waxing)
Full
Moon
Last
Quarter
(Waning)
• Resetting the seconds to 00 while the current count is in the range of 30 to 59
causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are
reset to 00 without changing the minutes.
• With the 12-hour format, the P (PM) indicator appears on the display for times in the
range of noon to 11:59 p.m. and the A (AM) indicator appears for times in the range
of midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.
• The year can be set in the range of 2000 to 2099.
• The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to change
it except after you have the watch’s batteries replaced.
• The Moon phase indicator shows the Moon as viewed at noon from a position in the
Northern Hemisphere looking south. Note that at times the image shown by the
Moon phase indicator may differ from that of the actual Moon in your area.
• The left-right orientation of the Moon phase is reversed when viewing from the
Southern Hemisphere or from a point near the equator.
World Time
Moon Phases and Moon Age
The Moon goes through a regular 29.53-day cycle. During each cycle, the Moon
appears to wax and wane as the relative positioning of the Earth, Moon, and Sun
changes. The greater the angular distance between the Moon and the Sun,* the more
we see illuminated.
* The angle to the Moon in relation to the direction at which the Sun is visible from the
Earth.
This watch performs a rough calculation of the current Moon age starting from day 0
of the moon age cycle. Since this watch performs calculations using integer values
only (no fractions), the margin for error of the displayed Moon age is ± 1 day.
Illumination Precautions
Thermometer
Accuracy at normal temperature: ± 30 seconds a month
Digital Timekeeping: Hour, minutes, seconds, a.m. (A)/p.m. (P), day, day of the week
Time format: 12-hour and 24-hour
Calendar system: Full Auto-calendar pre-programmed from the year 2000 to 2099
Other: Daylight Saving Time (summer time)/Standard Time; Home Site data settings
(UTC differential and longitude)
Analog Timekeeping: Hour, minutes (hand moves every 20 seconds)
Fishing Mode: Fishing level for a specified date and time; Moon phase indicator and
Moon age for a specified date
Thermometer:
Measurement and display range: –10.0°C to 60.0°C (or 14.0°F to 140.0°F)
Display unit: 0.1°C (or 0.2°F)
Thermometer measurement timing: During each even-numbered minute
Memory measurement timing: At the top and the bottom of each hour
Memory capacity: Up to 50 sets of data (time, temperature)
Temperature sensor precision: ± 2°C (± 3.6°F)
Other: Thermometer/temperature tendency graph switching in the Timekeeping Mode;
Temperature unit switching (°C/°F); Temperature sensor calibration (Range:
±10°C/±18°F and unit: 0.1°C/0.2°F)
Stopwatch:
Measuring unit: 1/100 second
Measuring capacity: 99:59' 59.99''
Measuring modes: Elapsed time, split time, two finishes
Countdown Timer:
Measuring unit: 1 second
Input range: 1 minute to 100 hours (1-minute increments and 1-hour increments)
Other: Auto-repeat timing
Alarm: Daily alarm; Hourly Time Signal
World Time: 50 cities (30 time zones)
Other: Standard time/Daylight Saving Time
Illumination: EL (electro-luminescent panel)
Other: Button operation tone on/off
Temperature Sensor Calibration
The temperature sensor built into the watch is calibrated at the factory and normally
requires no further adjustment. If you notice serious errors in the temperature readings
produced by the watch, you can calibrate the sensor to correct the errors.
Important!
Incorrectly calibrating the temperature sensor can result in incorrect readings.
Carefully read the following before doing anything.
• Compare the readings produced by the watch with those of another reliable and
accurate thermometer.
• If adjustment is required, remove the watch from your wrist and wait for 20 or 30
minutes to give the temperature of the watch time to stabilize.
lll
lll
To calibrate the temperature sensor
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2.
Press C nine times to display the temperature sensor
l ll
calibration screen.
3. Use D (+) and B (–) to change the calibration value.
• You can change the value in 0.1°C (0.2°F) steps, in a
range of ±10°C (±18°F). The calibration value shows
Calibration value
‘‘--.-’’ when the setting is outside the allowable range.
ll
• To return the calibration value to its default (no calibration, indicated by ‘‘- -’’),
press D and B at the same time.
• Temperature sensor calibration will not be possible if the current reading is
outside the allowable display range (–10.0°C/14.0°F to 60.0°C/140.0°F) and the
calibration value shows ‘‘- -’’.
• Setting a sensor calibration value does not affect temperature values that are
already stored in memory.
4. After configuring the setting you want, press A twice to exit the setting screen.
lll
lll
To specify the temperature display unit
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
l
l
screen.
l
2. Press C 10 times to display the temperature unit
setting screen.
3. Use D to switch between Celsius ( ) and Fahrenheit
( ).
• The initial factory default and the initial default after
Temperature unit
battery replacement is Celsius ( ).
• The seconds count of the World Time is synchronized with the seconds count of the
Timekeeping Mode.
• All World Time Mode times are calculated from the current time in the Timekeeping
Mode using UTC time differential values.
• The electro-luminescent panel that provides illumination loses power after very long use.
• Illumination may be hard to see when viewed under direct sunlight.
• The watch may emit an audible sound whenever the display is illuminated. This is due
to vibration of the EL panel used for illumination, and does not indicate malfunction.
• Illumination turns off automatically whenever an alarm sounds.
• Frequent use of illumination runs down the batteries.
Specifications
Battery: Two silver oxide batteries (Type: SR927W)
Approximately 2 years on type SR927W (assuming alarm operation 10 seconds per
day, one illumination operation 1.5 seconds per day, and temperature measurement
every 2 minutes)
Frequent use of illumination shortens the battery life.
ll
4. After configuring the setting you want, press A twice to exit the setting screen.
• The temperature display unit setting you select is also applied to temperature values
that are already stored in memory.
Button Operation Tone
The button operation tone sounds any time you press one
of the watch’s buttons. You can turn the button operation
tone on or off as desired.
• Even if you turn off the button operation tone, the alarm,
Hourly Time Signal, and Countdown Timer Mode alarm
all operate normally.
Mute indicator
To turn the button operation tone on and off
In any mode (except when a setting screen is on the
display), hold down C to toggle the button operation tone
on (mute indicator not displayed) and off (mute indicator
displayed).
• Since the C button is also the mode change button, holding it down to turn the
button operation tone on or off also causes the watch’s current mode to change.
• The mute indicator is displayed in all modes when the button operation tone is
turned off.
4
Operation Guide 5056
City Code Table
City
Code
City
PPG
HNL
ANC
YVR
SFO
LAX
DEN
MEX
CHI
MIA
NYC
CCS*
YYT
RIO
RAI
LIS
LON
BCN
PAR
MIL
ROM
BER
ATH
JNB
IST
CAI
JRS
MOW
JED
THR
DXB
KBL
KHI
MLE
Pago Pago
Honolulu
Anchorage
Vancouver
San Francisco
Los Angeles
Denver
Mexico City
Chicago
Miami
New York
Caracas
St. Johns
Rio De Janeiro
Praia
Lisbon
London
Barcelona
Paris
Milan
Rome
Berlin
Athens
Johannesburg
Istanbul
Cairo
Jerusalem
Moscow
Jeddah
Tehran
Dubai
Kabul
Karachi
Male
UTC Offset/
GMT Differential
City
Code
City
–11
–10
–9
DEL
DAC
RGN
BKK
JKT*
SIN*
HKG
BJS
SEL
TYO
ADL
GUM
SYD
NOU
WLG
TBU
Delhi
Dhaka
Yangon
Bangkok
Jakarta
Singapore
Hong Kong
Beijing
Seoul
Tokyo
Adelaide
Guam
Sydney
Noumea
Wellington
Nuku’Alofa
–8
–7
–6
–5
–4
–3.5
–3
–1
0
+1
+2
+3
+3.5
+4
+4.5
UTC Offset/
GMT Differential
+5.5
+6
+6.5
+7
+8
+9
+9.5
+10
+11
+12
+13
• Based on data as of March 2008.
• The rules governing global times (GMT
differential and UTC offset) and summer
time are determined by each individual
country.
* In December 2007, Venezuela changed
its offset from –4 to –4.5. Note however,
that this watch displays an offset of –4
(the old offset) for the CCS (Caracas,
Venezuela) city code.
+5
Site Data List
Site
Anchorage
Bahamas
Baja, California
Bangkok
Boston
Buenos Aires
Casablanca
Christmas Island
Dakar
Gold Coast
Great Barrier Reef, Cairns
Guam
Hamburg
Hong Kong
Honolulu
Jakarta
Jeddah
Karachi
Kona, Hawaii
Lima
Lisbon
London
Los Angeles
Maldives
Manila
Mauritius
Melbourne
Miami
Noumea
Pago Pago
Palau
Panama City
Papeete
Rio De Janeiro
Seattle
Shanghai
Singapore
Sydney
Tokyo
Vancouver
Wellington
UTC Offset/GMT Differential
Standard
DST/
Time
Summer Time
–9.0
–8.0
–5.0
–4.0
–7.0
–6.0
+7.0
+8.0
–5.0
–4.0
–3.0
–2.0
+0.0
+1.0
+14.0
+15.0
+0.0
+1.0
+10.0
+11.0
+10.0
+11.0
+10.0
+11.0
+1.0
+2.0
+8.0
+9.0
–10.0
–9.0
+7.0
+8.0
+3.0
+4.0
+5.0
+6.0
–10.0
–9.0
–5.0
–4.0
+0.0
+1.0
+0.0
+1.0
–8.0
–7.0
+5.0
+6.0
+8.0
+9.0
+4.0
+5.0
+10.0
+11.0
–5.0
–4.0
+11.0
+12.0
–11.0
–10.0
+9.0
+10.0
–5.0
–4.0
–10.0
–9.0
–3.0
–2.0
–8.0
–7.0
+8.0
+9.0
+8.0
+9.0
+10.0
+11.0
+9.0
+10.0
–8.0
–7.0
+12.0
+13.0
Longitude
149°W
77°W
110°W
101°E
71°W
58°W
8°W
158°W
17°W
154°E
146°E
145°E
10°E
114°E
158°W
107°E
39°E
67°E
156°W
77°W
9°W
0°E
118°W
74°E
121°E
57°E
145°E
80°W
166°E
171°W
135°E
80°W
150°W
43°W
122°W
121°E
104°E
151°E
140°E
123°W
175°E
•Based on data as of 2008.
5
Download PDF

advertising