Casio | PAS400B-5V | User's Manual | Casio Pas400b-5v User's Manual

MA0311-EB
Operation Guide 2632/2805
Getting Acquainted
Congratulations upon your selection of this CASIO watch. To get the most out of your
purchase, be sure to carefully read this manual and keep it on hand for later reference
when necessary.
About This Manual
Important!
The fishing/hunting time data, sunrise and sunset data, and moon phase indicator
produced by this watch are all based on calculations that use the watch’s current time,
date, and Home Site settings. Because of this, you should make sure that the current
date and time, and your Home Site data are all correct before using such data.
• When fishing or hunting, always take proper precautions to ensure your own
personal safety and the personal safety of others around you.
• Note that the fishing/hunting time data, sunrise and sunset data, and moon phase
indicator are all based on calculated values. They are provided only for reference
purposes.
• See the “Timekeeping” section of this manual for information about setting the
current time and date, and about specifying your Home Site.
(Light)
Module 2632
• The operational procedures for Modules 2632 and 2805
are identical. All of the illustrations in this manual show
Module 2632.
• Button operations are indicated using the letters shown
in the illustration.
• Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the “Reference” section.
Module 2805
General Guide
• In addition to the modes shown here, this watch also has a Time Memo feature.
• Press D to change from mode to mode.
• In any mode, press L to illuminate the display.
Timekeeping Mode
Fishing/Hunting
Time Mode
Sunrise/Sunset Mode
Recall Mode
Alarm Mode
Stopwatch Mode
Press
D.
Timekeeping
Graphic area
Use the Timekeeping Mode to set and view the current
time, date, and your Home Site.
Latitude
Moon phase indicator
• The Moon phase indicator shows the current Moon
Day of week
phase in accordance with the current date as kept in the
Timekeeping Mode.
• The graphic area that runs around the periphery of the
display indicates fishing/hunting times, as well as
daylight and nighttime hours.
PM indicator
Important!
Be sure to correctly configure the current time and date,
and your Home Site data (data for the site where you use
the watch) before using the functions of this watch.
• See “Home Site Data” about specifying your Home Site.
Year Month – Day
Hour : Minutes Seconds
Longitude
4. Press D to display the Latitude/Longitude setting
screen, and then change the setting.
• Press B to change the latitude value and E to
change the longitude.
• At first, pressing B or E increases the value. Press
C to toggle the B and E button operations
between increase and decrease.
• You can specify latitude in the range of 65°N to 65°S,
and longitude from 179°W to 180°E, both in 1-degree
units.
5. Press A to exit the setting screen.
• When you exit the setting screen after changing the latitude and/or longitude setting,
the graphic area around the periphery of the display performs an animated pattern
to indicate that the watch is performing internal calculations. This process can
continue for as long as 15 seconds. Wait until the animated pattern stops before
performing any other button operation.
To set the time and date
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
• While the seconds are flashing, press E to reset the
seconds count to 00.
2. Press D to move the flashing in the sequence shown
below to select other settings.
Seconds
Day
Hour
Month
Minutes
Year
Graphic Area
In the Timekeeping Mode, the graphic area can be used to view either a fishing/
hunting time graph or a daylight graph. Press E to toggle between them.
Fishing/Hunting Time Graph
Daylight Graph
12:00 (12:00 PM)
Level indicator
12/24-Hour
Format
3. While the hour, minutes, year, month, or day setting is flashing, use E (+) and B
(–) to change it.
• When the 12/24-hour setting is flashing, press E to toggle between 12-hour
(
) and 24-hour (
) timekeeping.
4. Press A twice to exit the setting screen.
• The first press of A displays the Home Site GMT differential setting screen.
Pressing A again exits the setting screen.
• When you exit the setting screen after changing the current time and/or date setting,
the graphic area around the periphery of the display performs an animated pattern
to indicate that the watch is performing internal calculations. This process can
continue for as long as 15 seconds. Wait until the animated pattern stops before
performing any other button operation.
• The day of the week is automatically displayed in accordance with the date (year,
month, and day) settings.
Home Site Data
Moon phase indicator, fishing/hunting time data, and sunrise and sunset data will not
be displayed properly unless Home Site data (GMT differential, latitude, and
longitude) is configured correctly.
• The GMT differential is a value that indicates the time difference between Greenwich
Mean Time and the time zone where a city is located.
• Note that you must add one hour to the current time setting and the GMT differential
of your time zone whenever you change to Daylight Saving Time (summer time).
Subtract one hour when you change back to Standard Time.
• The “Site Data List” provides GMT differential, latitude, and longitude information
around the world.
To configure Home Site data
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press A again to display the GMT differential setting
screen.
3. Use E (+) and B (–) to change it.
• You can specify a value in the range of –11.0 to
+14.0, in 0.5-hour units.
Press E.
6:00 AM
18:00
(6:00 PM)
0:00 (12:00 AM)
• The markings along the display’s graphic area show the 24 hours of each day. Each
graphic area segment represents 30 minutes. The flashing segment of the graphic
area indicates the current time.
• The fishing/hunting time graph indicates the times when fish or game can be
expected to be feeding. For more information, see “Using the Fishing/Hunting Time
Features”.
• The blackened part of the daylight graph indicates nighttime. For more information,
see “Sunrise/Sunset Mode”.
Using the Fishing/Hunting Time Features
Fishing/hunting time graph
Moon phase indicator
Moon age
Date (Year
Month – Day)
Your watch provides you with information about favorable
fishing/hunting times and other data (Moon phase and
age) at your Home Site for a particular date. You can even
configure a fishing/hunting alarm that alerts you when a
favorable fishing/hunting time has been reached.
• The fishing/hunting times shown by your watch are the
times when the moon is at its highest point (upper
transit), lowest point (lower transit), furthest point the
east (east transit), and furthest point to the west (west
transit) of your Home Site. These are favorable times for
fishing and hunting.
• For more details about the fishing/hunting times, see
“Fishing/Hunting Time Calculation”.
• See “Moon Phase Indicator” for information about the
Moon phase indicator.
Time (Hour : Minutes)
1
Operation Guide 2632/2805
Sunrise/Sunset Mode
To interpret the Fishing/Hunting Time Mode screen
Use D to enter the Fishing/Hunting Time Mode. When you do, the display
automatically cycles through the fishing/hunting times for the current date (as kept in
the Timekeeping Mode), starting from the upper transit time.
Level indicator
Daylight graph
Moon phase indicator
Moon age
You can use the Sunrise/Sunset Mode to look up the
sunrise and sunset times, as well as the Moon phase and
Moon age at the Home Site on a particular date.
Sunrise time Sunset time
To view the sunrise/sunset time for a particular date
1. Use D to enter the Sunrise/Sunset Mode.
• The sunrise and sunset times that appear first when
you enter the Sunrise/Sunset Mode is the data for the
Home Site and the date currently specified in the
Timekeeping Mode.
2. Use E (+) and B (–) to scroll through the dates.
• Displaying a different date causes an animated pattern
to play in the graphic area, indicating that the watch is
performing internal calculations. This process can
continue for as long as 15 seconds. Wait until the
animated pattern stops before performing any other
button operation.
2 seconds
Time
Fishing/
hunting
time graph
Day of
week
Time number
Date
• The time numbers indicate the following: x1 upper transit time, x2 west transit time,
x3 lower transit time, x4 east transit time.
• Fishing/hunting times are rounded off to the nearest five minutes.
• If any fishing/hunting time falls outside of the 24-hour period that constitutes the
current date, x:xx is displayed in place of the time.
• The level indicator shows the relative favorability of a fishing/hunting time
(calculated in accordance with Moon transit and phase) as shown in the table below.
Moon
Transit
Moon
Phase
Upper (Hour Angle = 0h)
Lower (Hour Angle = 12h)
West (Hour Angle = 6h)
East (Hour Angle = 18h)
Other
*
New moon
Full moon
First quarter
Last quarter
Other
None
* These indicators actually appear during Moon ages 12.1 to 15.7 (Full Moon and phase
immediately preceding it) and 26.9 to 0.9 (New Moon and phase immediately preceding it).
• With Module 2805, the level indicator is
12:00 (12:00 PM)
6:00 AM
18:00
(6:00 PM)
0:00 (12:00 AM)
.
• The fishing/hunting time graph indicates favorable
periods using segments, each of which represents
30 minutes.
• The upper transit and the lower transit periods extend
from the point one hour prior to the transit up to the
point one hour after the transit. The east and west
transit periods extend from the point 30 minutes prior to
the transit up to the point 30 minutes after the transit.
• The fishing/hunting times and graph are refreshed at
midnight each day.
• If you suspect that a fishing/hunting time is not correct
for some reason, check the Timekeeping Mode data
(current time, date, and Home Site settings), and make
changes as required.
To view fishing/hunting times and Moon data for a particular date
In the Fishing/Hunting Time Mode, use E (+) and B (–)
Day of week
to display the date whose fishing/hunting time, Moon
phase, and Moon age you want to view.
• Displaying a different date causes an animated pattern
to play in the graphic area, indicating that the watch is
performing internal calculations. This process can
continue for as long as 15 seconds. Wait until the
animated pattern stops before performing any other
button operation.
• You can select any date from 2000 to 2039.
Date
Fishing/Hunting Time Alarm
While the fishing/hunting time alarm is turned on, the watch performs a beeper or
vibrator alert operation for about five seconds whenever a favorable fishing/hunting
period is approached.
• The fishing/hunting alert operation is performed the first time the watch minutes
reach 00 or 30 after a favorable fishing/hunting period is entered.
• To stop an alert operation, press any button.
• For full details about the alert operation, see “Selecting the Alert Type”.
• Note that the fishing/hunting time alarm is disabled when any one of the following
conditions exists.
While setting the current time or Home Site data
While the watch is performing internal calculations (indicated by the animated pattern playing
in the graphic area)
While the watch is in the process of changing fishing/hunting time data at midnight each day
To turn the fishing/hunting time alarm on and off
1. Use D to enter the Timekeeping Mode.
2. Hold down B for about two seconds to toggle the
fishing/hunting alarm on (
displayed) and off (
not displayed).
• With Module 2805, the indicator is
.
• The
indicator flashes while a fishing/hunting time
alert operation is in progress.
• The
indicator is displayed in all modes while the
alarm is turned on.
Selecting the Alert Type
You can select either beeper or vibrator as the alert for the fishing/hunting time alarm,
daily alarm, weekly alarm, and Hourly Time Signal.
• Nearby very magnetic force can cause the watch’s vibration alert to become weak or
even fail to operate entirely.
To switch between vibration alert and beeper alert
1. Use D to enter the Timekeeping Mode.
2. Hold down E for about two seconds to toggle between
vibration alert (VIB displayed) and beeper alert (VIB not
displayed).
• The watch performs the newly selected alert operation
whenever you perform the above procedure to switch
between vibration alert and beeper alert.
• The vibration alert on indicator (VIB) is displayed in all
modes.
Date
• See “Moon Phase Indicator” for information about the Moon phase indicator.
• You can select any date from 2000 to 2039.
Note
• The daylight graph indicates daytime and nighttime in
accordance with the sunrise and sunset times
calculated by the watch.
12:00 (12:00 PM)
• If you suspect that a sunrise/sunset time is not correct
or if the daylight graph does not appear for some
18:00
reason, check the Timekeeping Mode data (current
(6:00 PM)
6:00 AM
time, date, and Home Site settings), and make changes
as required. If the daylight graph does not appear, it
could indicate a problem with the GMT differential or
Sunrise
Sunset
longitude setting.
0:00 (12:00 AM)
• The sunrise and sunset times displayed by this watch
Nighttime
are times at sea level. Sunrise and sunset times are
different at altitudes other than sea level.
Daylight Graph
• Sunrise and sunset times, and the contents of the daylight graph refresh each day at
midnight.
• Sunrise and sunset times are rounded off to the nearest five minutes.
Date
12/5
12/6
12/7
12/8
12/9
Sunset Time
P 4:25
P 4:25
P 4:30
P 4:25
P 4:25
• Normally, actual sunrise and sunset times change very
little from day to day. Sometimes, however, the watch
may show a change of as much as five minutes from
one day to the next. Note that this is because the watch
calculates sunrise and sunset times, and then rounds
the result to the nearest five minutes. It does not
indicate malfunction of the watch.
• Sunrise and sunset time calculations are accurate within
about five minutes. At north or south latitudes greater
than 50 degrees, however, accuracy is within about
10 minutes.
Time Memo
The Time Memo feature of your watch lets you create up to 40 time memos, each of
which includes a memo number, as well as the time, date, Moon phase indicator, and
the fishing/hunting level indicator at the point when the time memo is recorded. You
can create time memos to keep track of how many fish you catch or how much game
you bag, as well at the date, time, and Moon phase.
Time memos are automatically sorted chronologically on their date and time fields.
You can recall time memos by scrolling through them on the display.
• You can create a time memo while in any mode. However, you cannot create a time
memo while a setting screen is on the display.
• Use the Recall Mode to recall and delete time memos.
• Each memo date shows the month and day only.
To create a time memo
Memo number
Memo time
In any mode, hold down C for about two seconds until
the memo number and memo time flash on the display.
• When you initially press C, the memo number and
memo time appear on the display. Keep C depressed
until they start flashing. Note that no time memo is
created if you release C while the memo number and
memo time are not flashing.
• The memo number and memo time flash for about two
seconds, and then the display changes to the screen
that was displayed before you pressed C.
• Note that you cannot create a time memo if the current
time is midnight or while the watch is performing a
calculation operation.
• Creating a time memo while memory is full deletes the oldest time memo and stores
the new one.
• Memo numbers restart from #0[ with each new day. Because of this, you can use
memo numbers to count how many fish you catch or how much game you bag.
• Memos are numbered starting from #0[. If you record more than 99 memos, the
100th memo is numbered #00, and subsequent memo numbering continues in
sequence (#0[, #02, etc.) after that.
• Note that the memo number count is reset to #0[ only when the Timekeeping
Mode reaches midnight as a function of normal timekeeping. The count will not be
reset if you scroll past midnight while changing the Timekeeping Mode current time
setting.
Managing Time Memos
Use the Recall Mode to recall and delete time memos. Use D to enter the Recall
Mode.
• Entering the Recall Mode initially displays the last time memo you created.
• Performing the time memo delete operation deletes all time memos currently in
memory. Note that you cannot delete time memos individually.
• Having the watch’s battery replaced will cause all time memos currently in memory
to be deleted. Make sure you always keep separate copies of important data.
2
Operation Guide 2632/2805
Stopwatch
To recall time memos
Level indicator
Moon phase indicator
Memo number
Memo date
In the Recall Mode, use E (+) and B (–) to scroll
through time memos on the display.
• For details about the level indicator and the fishing/
hunting time graph, see “To interpret the Fishing/Hunting
Time Mode screen”.
To delete all time memos
In the Recall Mode, hold down A for about two seconds,
until CLR flashes on the display.
• When you initially press A, CLR appears on the
display. Keep A depressed until it starts flashing.
• After CLR flashes for about two seconds, the memo
number changes to
, which indicates that all time
memos have been deleted.
Memo time
Hours
The stopwatch lets you measure elapsed time, split times,
and two finishes.
• The display range of the stopwatch is 23 hours,
59 minutes, 59.99 seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
• Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing D.
Seconds
Minutes
1/100 second
To measure times with the stopwach
Elapsed Time
Fishing/hunting time graph
Start
Alarm on indicator
Hourly time signal on
indicator
Day of week
Stop
Re-start
Stop
Clear
Split release
Stop
Clear
Split
Stop
Split release
Clear
First runner
finishes.
Display time of
first runner.
Second runner
finishes.
Display time of
second runner.
Split Time
Alarms
You can set up to five independent alarms with hour,
minutes, and day of the week. When an alarm is turned
on, an alert operation (beep or vibration) is performed
when the alarm time is reached.
You can also turn on an Hourly Time Signal that causes
the watch to beep or vibrate twice every hour on the hour.
• There are five alarm screens numbered1 through 5.
The Hourly Time Signal screen is indicated by :00 in
place of the alarm time.
• You can configure alarm time settings and Hourly Time
Signal settings in the Alarm Mode, which you enter by
pressing D.
• When you enter the Alarm Mode, the screen you were
viewing when you last exited the mode appears first.
Start
Split
(
Two Finishes
Start
Backlight
The backlight uses an EL (electro-luminescent) panel that
causes the entire display to glow for easy reading in the
dark. The watch’s auto light switch automatically turns on
the backlight when you angle the watch towards your
face.
• The auto light switch must be turned on (indicated by
the auto light switch on indicator) for it to operate.
• See “Backlight Precautions” for other important
information about using the backlight.
Timekeeping Alarm
Mode time
number
Alarm time (Hour : Minutes)
Alarm Types
The alarm type is determined by the settings you configure, as described below.
• Daily alarm
Set the hour and minutes for the alarm time. This type of setting causes an alert
operation (beep or vibration) to be performed everyday at the time you set.
• Weekly alarm
Set the hour, minutes, and the day of the week for the alarm time. This type of setting
causes an alert operation (beep or vibration) to be performed every week at the time
you set, on the day of the week you set.
displayed)
Auto light switch
on indicator
To turn on the backlight manually
In any mode, press L to illuminate the display for about
two seconds.
• The above operation turns on the backlight regardless
of the current auto light switch setting.
About the Auto Light Switch
To set an alarm time
1. In the Alarm Mode, use E to display the alarm screen.
Turning on the auto light switch causes the backlight to turn on for about two seconds,
whenever you position your wrist as described below in any mode.
Moving the watch to a position that is parallel to the ground and then tilting it
towards you more than 40 degrees causes the backlight to turn on.
2. After you select an alarm, hold down A until the hour
setting of the alarm time starts to flash, which indicates
the setting screen.
• This operation automatically turns on the alarm.
3. Press D to move the flashing in the sequence shown
below to select other settings.
Hour
Minutes
Day of week
4. While a setting is flashing, use E (+) or B (–) to change it.
• To set an alarm that does not include a day of the week (daily alarm), set --for the day of the week. Press E or B until the --- mark appears (between
SAT and SUN) while the day of the week setting is flashing.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (no indicator) or p.m. (P indicator).
5. Press A to exit the setting screen.
Alert Operation
The alert operation (beep or vibration) is performed at the preset time for about
10 seconds.
• To stop the alert operation, press any button.
• The alarm and the Hourly Time Signal alert operations (beep or vibration) are
performed in all modes except for the Timekeeping Mode setting screen.
• For information about changing the alert type, see “To switch between vibration alert
and beeper alert”.
Parallel to ground
More than 40 °
Warning!
• Always make sure you are in a safe place whenever you are reading the
display of the watch using the auto light switch. Be especially careful when
running or engaged in any other activity that can result in accident or injury.
Also take care that sudden illumination by the auto light switch does not
surprise or distract others around you.
• When you are wearing the watch, make sure that its auto light switch is turned
off before riding on a bicycle or operating a motorcycle or any other motor
vehicle. Sudden and unintended operation of the auto light switch can create
a distraction, which can result in a traffic accident and serious personal injury.
To turn the auto light switch on and off
In the Timekeeping Mode, hold down L for about two seconds to toggle the auto light
switch on (AUTO EL displayed) and off (AUTO EL not displayed).
• The auto light switch on indicator (AUTO EL ) is on the display in all modes while
the auto light switch is turned on.
• In order to protect against running down the battery, the auto light switch
automatically turns off approximately six hours after you turn it on. Repeat the above
procedure to turn the auto light switch back on if you want.
To test the alert operation
In the Alarm Mode, hold down E to perform the currently selected alert operation.
To turn an alarm on and off
1. In the Alarm Mode, use E to select an alarm.
2. Press B to toggle it on (x displayed) and
off (x not displayed).
• In all modes (except for the Timekeeping Mode setting
screen), the alarm on indicator is shown for any alarm
that is currently turned on.
• The alarm on indicator flashes while the alarm is
sounding.
To turn the Hourly Time Signal on and off
1. In the Alarm Mode, use E to select the Hourly Time Signal (:00).
2. Press B to toggle it on (ydisplayed) and off (ynot displayed).
• The Hourly Time Signal on indicator is shown on the display in all modes while the
Hourly Time Signal is turned on.
3
Operation Guide 2632/2805
Reference
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
Moon Phases and Moon Age
The Moon goes through a regular 29.53-day cycle during which it appears to wax and
wane due to how the Sun illuminates the Moon and the relative positioning of the
Earth, Moon, and Sun. The greater the angular distance between the Moon and the
Sun,* the more we see illuminated.
* The angle to the Moon in relation to the direction at which the Sun is visible from the Earth.
The Moon age indicates the number of days from the New Moon to any particular
phase. It is normally calculated using either noon or midnight as a reference point.
This watch calculates the Moon age based on the angular distance of the Moon at
noon, which can result in an error of ±1 day. Because of this, the appearance of the
Moon phase indicator may be different from that of the actual Moon.
The watch uses the following formula to calculate Moon age.
Moon Age (days) = 29.53 X (Moon angular distance / 360°)
Moon Phase Indicator
The Moon phase indicator of this watch indicates the current phase of the Moon as
shown below.
Moon phase (Part you cannot see)
(Part you can see)
Moon Phase
Indicator
Moon Age
28.7 - 29.5 1.0 - 2.7
0.0 - 0.9
2.8 - 4.6
Moon Phase New
4.7 - 6.4
6.5 - 8.3
8.4 - 10.1 10.2 - 12.0 12.1 - 13.8
First
Quarter
(Waxing)
Moon
Moon Phase
Indicator
Moon Age
13.9 - 15.7 15.8 - 17.5 17.6 - 19.4 19.5 - 21.2 21.3 - 23.1 23.2 - 24.9 25.0 - 26.8 26.9 - 28.6
Moon Phase Full
Backlight Precautions
• The electro-luminescent panel that provides illumination loses power after very long
use.
• The illumination provided by the backlight may be hard to see when viewed under
direct sunlight.
• The watch may emit an audible sound whenever the display is illuminated. This is
due to vibration of the EL panel used for illumination, and does not indicate
malfunction.
• The backlight automatically turns off whenever an alarm sounds.
• Frequent use of the backlight shortens battery life.
Auto light switch precautions
• Wearing the watch on the inside of your wrist and movement or vibration of your arm
can cause the auto light switch to activate and illuminate the display. To avoid
running down the battery, turn off the auto light switch whenever engaging in
activities that might cause frequent illumination of the display.
More than 15 degrees
too high
• The backlight may not light if the face of the watch is
more than 15 degrees above or below parallel. Make
sure that the back of your hand is parallel to the ground.
• The backlight turns off in about two seconds, even if you
keep the watch pointed towards your face.
• Static electricity or magnetic force can interfere with
proper operation of the auto light switch. If the backlight
does not light, try moving the watch back to the starting
position (parallel with the ground) and then tilt it back
toward you again. If this does not work, drop your arm
all the way down so it hangs at your side, and then bring
it back up again.
• Under certain conditions, the backlight may not light
until about one second after you turn the face of the
watch towards you. This does not necessarily indicate
malfunction of the backlight.
Last
Quarter
(Waning)
Moon
• The Moon phase indicator shows the Moon as viewed at noon from a position in the
Northern Hemisphere looking south. Note that at times the image shown by the
Moon phase indicator may differ from that of the actual Moon in your area.
• The left-right orientation of the Moon phase is reversed when viewing from the
Southern Hemisphere or from a point near the equator.
• The Moon phase indicator refreshes each day at midnight.
Fishing/Hunting Time Calculation
The fishing/hunting times calculated by this watch are based on the long experience
of fishermen and hunters that the movements of the moon and tides affect fish and
game. The following explains how the moon’s transit (position) affects the feeding
patterns of fish and game.
Upper Transit
Moon
West
Transit
East
Transit
Earth
Lower Transit
• During the month, the most feeding action can be
expected on the day of the New Moon and Full Moon,
making them the best for hunting and fishing. Favorable
conditions with less action can be expected on the day
of the First Quarter and Last Quarter as well.
• On a daily basis, optimum hunting and fishing conditions
occur at the upper transit (hour angle= 0h) and the lower
transit (hour angle = 12h). Other less favorable
conditions can be expected at the west transit (hour
angle 6h) and east transit (hour angle = 18h).
• The upper transit is when the Moon reaches its highest
point relative to your current location, while the lower
transit is when the Moon reaches its lowest point. The
time it takes to perform one cycle from one upper transit
to the next upper transit is the “lunar day”. Due to the
relationship between the Earth’s rotation and the Moon’s
orbit, the length of the lunar day is 24 hours and
50 minutes.
• Note that water temperature, weather, atmospheric pressure, and other factors can
also affect fish and animal behavior.
Your watch calculates the current Moon age, phase, and transit (hour angle) for the
current date in relation to your Home Site, and then uses the calculated result to
calculate and display fishing/hunting time data.
Auto Return Feature
If you leave a screen with flashing digits on the display for two or three minutes
without performing any operation, the watch automatically exits the setting screen.
Scrolling
The B and E buttons are used in various modes and setting screens to scroll
through data on the display. In most cases, holding down these buttons during a scroll
operation scrolls through the data at high speed.
Timekeeping
• Resetting the seconds to 00 while the current count is in the range of 30 to 59
causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are
reset to 00 without changing the minutes.
• With the 12-hour format, the P (PM) indicator appears on the display for times in the
range of noon to 11:59 p.m. and no indicator appears for times in the range of
midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all modes.
• The year can be set in the range of 2000 to 2039.
• The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to change
it except after you have the watch’s battery replaced.
4
Operation Guide 2632/2805
Site Data List
Site
ABIDJAN
ABU DHABI
ADDIS ABABA
ADEN
AMSTERDAM
ANCHORAGE
ATHENS
AZORES
BANGKOK
BEIJING
BEIRUT
BOGOTA
BOSTON
BRASILIA
BUENOS AIRES
CAPE TOWN
CARACAS
CASABLANCA
CHICAGO
CHRISTCHURCH
DAKAR
DALLAS
FORT WORTH
DAMASCUS
DENVER
DETROIT
DHAKA
DUBAI
DUBLIN
EDMONTON
EL PASO
FRANKFURT
GOLD COAST
GUAM
HAMBURG
HANOI
HELSINKI
HONG KONG
HONOLULU
HOUSTON
ISTANBUL
JAKARTA
JEDDAH
KARACHI
KUALA LUMPUR
KUWAIT
LA PAZ
LAS VEGAS
LIMA
LISBON
LONDON
LOS ANGELES
MADRID
MANILA
MELBOURNE
MEXICO CITY
MIAMI
MILAN
MONTEVIDEO
MONTREAL
MUSCAT
NADI
NAIROBI
NAURU ISLAND
NEW ORLEANS
NEW YORK
NOME
NOUMEA
PAGO PAGO
PANAMA CITY
PAPEETE
PARIS
PERTH
PHNOM PENH
PORT OF SPAIN
PORT VILA
PRAIA
PYONGYANG
RIYADH
ROME
SAN FRANCISCO
SANTIAGO
SAO PAULO
SEATTLE
SEOUL
SHANGHAI
SINGAPORE
STOCKHOLM
SYDNEY
TAIPEI
TOKYO
ULAANBAATAR
GMT Differential
DST/
Standard Time Summer Time
0.0
1.0
4.0
5.0
3.0
4.0
3.0
4.0
1.0
2.0
–9.0
–8.0
2.0
3.0
–1.0
0.0
7.0
8.0
8.0
9.0
2.0
3.0
–5.0
–4.0
–5.0
–4.0
–3.0
–2.0
–3.0
–2.0
2.0
3.0
–4.0
–3.0
0.0
1.0
–6.0
–5.0
12.0
13.0
0.0
1.0
Longitude
Latitude
4°W
54°E
39°E
45°E
5°E
149°W
24°E
25°W
101°E
116°E
36°E
74°W
71°W
48°W
58°W
18°E
67°W
8°W
88°W
173°E
17°W
5°N
24°N
9°N
13°N
52°N
61°N
38°N
38°N
14°N
40°N
34°N
5°N
42°N
16°S
35°S
34°S
11°N
34°N
42°N
44°S
15°N
–6.0
–5.0
97°W
33°N
2.0
–7.0
–5.0
6.0
4.0
0.0
–7.0
–7.0
1.0
10.0
10.0
1.0
7.0
2.0
8.0
–10.0
–6.0
2.0
7.0
3.0
5.0
8.0
3.0
–4.0
–8.0
–5.0
0.0
0.0
–8.0
1.0
8.0
10.0
–6.0
–5.0
1.0
–3.0
–5.0
4.0
12.0
3.0
12.0
–6.0
–5.0
–9.0
11.0
–11.0
–5.0
–10.0
1.0
8.0
7.0
–4.0
11.0
–1.0
9.0
3.0
1.0
–8.0
–4.0
–3.0
–8.0
9.0
8.0
8.0
1.0
10.0
8.0
9.0
8.0
3.0
–6.0
–4.0
7.0
5.0
1.0
–6.0
–6.0
2.0
11.0
11.0
2.0
8.0
3.0
9.0
–9.0
–5.0
3.0
8.0
4.0
6.0
9.0
4.0
–3.0
–7.0
–4.0
1.0
1.0
–7.0
2.0
9.0
11.0
–5.0
–4.0
2.0
–2.0
–4.0
5.0
13.0
4.0
13.0
–5.0
–4.0
–8.0
12.0
–10.0
–4.0
–9.0
2.0
9.0
8.0
–3.0
12.0
0.0
10.0
4.0
2.0
–7.0
–3.0
–2.0
–7.0
10.0
9.0
9.0
2.0
11.0
9.0
10.0
9.0
36°E
105°W
83°W
90°E
55°E
6°W
114°W
106°W
9°E
154°E
145°E
10°E
106°E
25°E
114°E
158°W
95°W
29°E
107°E
39°E
67°E
102°E
48°E
68°W
115°W
77°W
9°W
0°E
118°W
4°W
121°E
145°E
99°W
80°W
9°E
56°W
74°W
59°E
177°E
37°E
167°E
90°W
74°W
165°W
166°E
171°W
80°W
150°W
2°E
116°E
105°E
62°W
168°E
24°W
126°E
47°E
13°E
122°W
71°W
47°W
122°W
127°E
121°E
104°E
18°E
151°E
121°E
140°E
107°E
34°N
40°N
42°N
24°N
25°N
53°N
54°N
32°N
50°N
28°S
13°N
54°N
21°N
60°N
22°N
21°N
30°N
41°N
6°S
22°N
25°N
3°N
29°N
17°S
36°N
12°S
39°N
52°N
34°N
40°N
15°N
38°S
19°N
26°N
45°N
35°S
46°N
24°N
18°S
1°S
1°S
30°N
41°N
64°N
22°S
14°N
9°N
18°S
49°N
32°S
12°N
11°N
18°S
15°N
39°N
25°N
42°N
38°N
33°S
24°S
48°N
38°N
31°N
1°N
59°N
34°S
25°N
36°N
48°N
Site
GMT Differential
DST/
Standard Time Summer Time
–8.0
–7.0
1.0
2.0
7.0
8.0
12.0
13.0
–6.0
–5.0
VANCOUVER
VIENNA
VIENTIANE
WELLINGTON
WINNIPEG
• Based on data as of 2003.
Longitude
Latitude
123°W
16°E
103°E
175°E
97°W
49°N
48°N
18°N
41°S
50°N
5
Download PDF

advertising