HS-3000/4M
386 ISA Bus SBC
•CRT/Panel•RS-232/422/485•4 COM•
•PC/104•DOC•WDT•Single +5V•
ISA Bus Industrial Single Board Computer
C
Cooppyyrriigghhtt D
Diissccllaaiim
meerrss
The accuracy of contents in this manual has passed thorough checking and review
before publishing. BOSER Technology Co., Ltd., the manufacturer and publisher, is
not liable for any infringements of patents or other rights resulting from its use. The
manufacturer will not be responsible for any direct, indirect, special, incidental
or consequential damages arising from the use of this product or
documentation, even if advised of the possibility of such damage(s).
This manual is copyrighted and BOSER Technology Co., Ltd. reserves all
documentation rights. Unauthorized reproduction, transmission, translation,
and storage of any form and means (i.e., electronic, mechanical, photocopying,
recording) of this document, in whole or partly, is prohibited, unless granted
permission by BOSER Technology Co., Ltd.
BOSER Technology Co., Ltd. reserves the right to change or improve the
contents of this document without due notice. BOSER Technology Co., Ltd.
assumes no responsibility for any errors or omissions that may appear in this
manual, nor does it make any commitment to update the information contained
herein.
TTrraaddeem
maarrkkss
BOSER is a registered trademark of BOSER Technology Co., Ltd.
ISB is a registered trademark of BOSER Technology Co., Ltd.
Intel is a registered trademark of Intel Corporation.
Award is a registered trademark of Award Software, Inc.
AMI is a registered trademark of AMI Software, Inc.
All other trademarks, products and or product names mentioned herein are
mentioned for identification purposes only, and may be trademarks and/or
registered trademarks of their respective companies or owners.
© Copyright 2004 BOSER Technology Co., Ltd.
All Rights Reserved.
Edition 1.6 August 05, 2004
Table of Contents
Chapter 1
General Description..............................1
1.1 Major Features .................................................................. 2
1.2 Specifications ................................................................... 3
1.3 Board Dimensions............................................................ 4
Chapter 2
Unpacking .............................................5
2.1 Opening the Delivery Package........................................ 5
2.2 Inspection.......................................................................... 5
Chapter 3
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
3.10
3.11
3.12
3.13
3.14
3.15
3.16
3.17
Hardware Installation ..........................7
Before Installation ............................................................ 7
Board Layout .................................................................... 8
Jumper List ....................................................................... 9
Connector List .................................................................. 9
DiskOnChip Address Setting ..................................... 10
Watchdog Timer ............................................................. 10
VGA Controller................................................................ 12
Serial Port Connectors .................................................. 17
Keyboard & Mouse Connector...................................... 18
Speaker Connector ........................................................ 19
PCI E-IDE Drive Connector............................................ 20
Parallel Connector.......................................................... 21
Power and LED Connectors .......................................... 21
Floppy Disk Drive Connector ........................................ 22
Flash ROM Type ............................................................. 23
System Memory .............................................................. 23
PC/104 Bus Connection................................................. 23
Chapter 4
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
4.10
4.11
4.12
4.13
4.14
AMI BIOS Setup.................................27
Starting Setup ................................................................. 27
Using Setup..................................................................... 28
Main Menu ....................................................................... 29
Standard CMOS Setup ................................................... 30
Advanced CMOS Setup ................................................. 31
Advanced Chipset Setup ............................................... 32
PCI / Plug And Play Setup ............................................. 33
Peripheral Setup............................................................. 34
Auto-Detect Hard Disks ................................................. 35
Change Supervisor/User Password ............................. 36
Auto Configuration with Optimal Settings................... 37
Auto Configuration with Fail Safe Settings ................. 38
Save Settings and Exit................................................... 39
Exit Without Saving........................................................ 40
SSaaffeettyy IInnssttrruuccttiioonnss
Integrated circuits on computer boards are sensitive to static electricity.
To avoid damaging chips from electrostatic discharge, observe the
following precautions:
Do not remove boards or integrated circuits from their anti-static
packaging until you are ready to install them.
Before handling a board or integrated circuit, touch an unpainted portion
of the system unit chassis for a few seconds. This helps to discharge any
static electricity on your body.
Wear a wrist-grounding strap, available from most electronic component
stores, when handling boards and components. Fasten the ALLIGATOR
clip of the strap to the end of the shielded wire lead from a grounded
object. Please wear and connect the strap before handle the
HS-3000/4M to ensure harmlessly discharge any static electricity
through the strap.
Please use an anti-static pad when putting down any components or
parts or tools outside the computer. You may also use an anti-static bag
instead of the pad. Please inquire from your local supplier for additional
assistance in finding the necessary anti-static gadgets.
NOTE:
DO NOT TOUCH THE BOARD OR ANY OTHER SENSITIVE
COMPONENTS WITHOUT ALL NECESSARY ANTI-STATIC
PROTECTION.
This page is intentionally left blank.
Chapter 1
General Description
The HS-3000/4M is ISA Bus ALi M6117C chipset industrial single
board computer. The board design combine together with all necessary
input and output effects interfaces which makes it an ideal all-in-one
industrial single board computer. The board design with 40MHz Bus
clock rate architecture. The HS-3000/4M supports one SIMM socket
with a max. capacity of 16MB and 4MB RAM onboard.
The IDE interface with LBA mode access to IDE drive interface
architecture, supports with max. 11MB/sec in a data transfers rating to
two IDE drive connection. One set of PC/104 Bus connector for 16-bit
ISA Bus.
A single Flash chip holds the system BIOS, and you can change the
Flash BIOS by the Utility Update. You can also use the DOS version of
the "DiskOnChip" socket by issuing commands from the DOS prompt
without the necessity of other software supports up to 288MB.
1
The board design with 65545 CRT/Panel display controller provides
internal connections to CRT or Panel. The VGA provides up to 1024 x
768 x 16 colors resolution.
If a non-expect program cause halts, the onboard Watchdog Timer
(WDT) will automatically reset the CPU or generate an interrupt. The
WDT is designed with pure hardware and doesn’t need any arithmetical
functions of a real-time clock chip. This ensures the reliability in an
unmanned or standalone system.
1.1
Major Features
The HS-3000/4M comes with the following features:
Intel® 386SX compatible CPU
One SIMM socket with a max. capacity of 16MB and 4MB RAM onboard
ALi M6117C system chipset
SMC 37C669 super I/O chipset
C&T 65545 CRT/Panel display controller
Four COM connectors
PC/104 Bus connector
DiskOnChip
TM
socket supporting memory sizes of up to 288MB
Single +5V power in
2
1.2
Specifications
CPU: 386SX-40 embedded in ALi M6117C chipset
Bus Interface: ISA Bus
Memory: One SIMM socket with a max. capacity of 16MB and 4MB RAM
onboard
Chipset: ALi M6117C
I/O Chipset: SMC 37C669 x 2
VGA: C&T 65545 with 1MB memory supporting CRT/Panel displays up
to 1024 x 768 at 16 colors
IDE: Two IDE disk drives supporting LBA mode and with a transfer rate
of 11MB/sec.
FDD: Supports up to two floppy disk drives
Parallel: One enhanced bi-directional parallel port supporting SPP/ECP/
EPP
Serial Port: 16C550 UART-compatible RS-232/422/485 x 1 and RS-232
x 3 serial ports with 16-byte FIFO
PC/104: PC/104 connector for 16-bit ISA Bus
Keyboard: PS/2 6-pin Mini DIN or 5-pin connector
Mouse: PS/2 6-pin Mini DIN
TM
DiskOnChip : DiskOnChipTM socket supporting memory sizes of up to
288MB
BIOS: AMI PnP Flash BIOS
Watchdog Timer: Sets 1/2/10/20/110/220 seconds activity trigger with
Reset or NMI
CMOS: DS12C887 or equivalent device
Power: Single +5V/1.8A power in
Power Connector: One 4-pin +5V/+12V power connector
Temperature: 0~60°C (operating)
Dimensions: 18.6 x 12.2 cm
3
1.3
4
Board Dimensions
Chapter 2
Unpacking
This chapter explains unpacking the board, checking the equipment
and documentation and where to go from there.
2.1
Opening the Delivery Package
The HS-3000/4M is packed in an anti-static bag. The board has
components that are easily damaged by static electricity. Do not
remove the anti-static wrapping until proper precautions have been
taken. Safety Instructions in front of this manual describe anti-static
precautions and procedures.
2.2
Inspection
After unpacking the board, place it on a raised surface and carefully
inspect the board for any damage that might have occurred during
shipment. Ground the board and exercise extreme care to prevent
damage to the board from static electricity. Integrated circuits will
sometimes come out of their sockets during shipment. Examine all
integrated circuits, particularly the BIOS, processor, memory modules,
ROM-Disk, and keyboard controller chip to ensure that they are firmly
seated. The HS-3000/4M delivery package contains the following
items:
HS-3000/4M Board x 1
IDE port flat cable x 1
FDD port flat cable x 1
Printer + one COM flat cable with bracket x 1
Two COM flat cable with bracket x 1
Utility CD Disk x 1
User’s Manual x 1
5
It is recommended that you keep all the parts of the delivery package
intact and store them in a safe/dry place for any unforeseen event
requiring the return shipment of the product. In case you discover any
missing and/or damaged items from the list of items, please contact
your dealer immediately.
6
Chapter 3
Hardware Installation
This chapter provides the information on how to install the hardware
using the HS-3000/4M. This chapter also contains information related
to jumper settings of switch, watchdog timer, and the DiskOnChip
address selection etc.
3.1
Before Installation
After confirming your package contents, you are now ready to install
your hardware. The following are important reminders and steps to take
before you begin with your installation process.
1. Make sure that all jumper settings match their default settings
and CMOS setup correctly. Refer to the sections on this chapter
for the default settings of each jumper.
2. Go through the connections of all external devices and make
sure that they are installed properly and configured correctly
within the CMOS setup. Refer to the sections on this chapter for
the detailed information on the connectors.
3. Keep the manual and diskette in good condition for future
reference and use.
7
3.2
8
Board Layout
3.3
Jumper List
Jumper
JP1
JP8
JP9
JP11
JP12
JP13
JP14
JP15
3.4
Definition
COM 4 Use RS-232 or RS-422/485 Select:
RS-232
IRQ12 Enabled/Disabled Select: Enabled
WDT Active Type Select: Reset System
DiskOnChipTM Address Select: D000
RS-422/485 Receiver Enabled/Disabled Select:
Always Enabled
RS-422/485 Transmitter Enabled/Disabled
Select: Always Enabled
WDT Out Period Select: 1 sec.
Flash ROM Type Select: 29C010
Setting Page
Open
17
Short
Short 1-2
Short 1-2
18
10
10
Short 1-2
17
Short 1-2
17
Short 5-6
Short 1-2
10
23
Connector List
Connector
CN1
CN2
CN3
CN4
CN5
CN6
CN7
CN8
CN9
CN10
CN11
CN12
CN14
CN15
CN16
CN17
CN18
CN19
CN20
CN21
Definition
4-pin Power Connector
Parallel Connector
Reset Button Connector
Keylock Connector
Speaker Connector
IDE LED Connector
Floppy Connector
PC/104 Bus 64-pin Connector
PC/104 Bus 40-pin Connector
IDE Connector
Panel Connector
RS-422/485 Connector
COM 2 Connector (5x2 header)
COM 3 Connector (5x2 header)
COM 4 Connector (5x2 header)
COM 1 Connector (DB9)
15-pin CRT Connector
5-pin Keyboard Connector
PS/2 6-pin Mini DIN Mouse Connector
PS/2 6-pin Mini DIN Keyboard Connector
Page
21
21
21
21
19
21
22
23
23
20
12
17
17
17
17
17
12
18
18
18
9
3.5
DiskOnChip Address Setting
The DiskOnChipTM function allows the system to boot or operate
without a FDD or a HDD. DiskOnChipTM modules may be formatted as
drive C or A. With DiskOnChipTM, user may also execute DOS
commands such as FORMAT, SYS, COPY, XCOPY, DISCOPY and
DISKCOMP etc.
The U9 location onboard the HS-3000/4M is the DiskOnChip module
socket. Jumper JP11 assigns the address setting of the installed
module. Setting the 8 pins of JP11 allows you to select the starting
memory address of the DiskOnChipTM (D.O.C.). If you have additional
memory devices in the system, please set both at different memory
address mapping to avoid the mapping area conflicts.
JP11: DiskOnChip Address Select
3.6
JP11
Address
Short 1-2 (default)
Short 3-4
Short 5-6
Short 7-8
D000
D800
E000
E800
2
8
1
7
Watchdog Timer
There are three access cycles of watchdog timer as Enable, Refresh and
Disable. The Enable cycle should proceed by READ PORT 443H. The
Disable cycle should proceed by READ PORT 043H. A continue Enable
cycle after a first Enable cycle means Refresh.
Once if the Enable cycle activity, a Refresh cycle is request before the
time-out period for restart counting the WDT Timer’s period. Otherwise, it
will assume that the program operation is abnormal when the time counting
over the period preset of WDT Timer. A System Reset signal to start again
or a NMI cycle to the CPU comes if over.
The JP9 is using for select the active function of watchdog timer in disable
the watchdog timer, or presetting the watchdog timer activity at the reset
trigger, or presetting the watchdog timer activity at the NMI trigger.
10
JP9: Watchdog Timer Active Type Select
JP9
Description
Short 1-2 (default)
Short 2-3
Open
System Reset
Active NMI
Disabled
1
3
JP14: Watchdog Timer Out Period Select
Period PINS 1-2 PINS 3-4 PINS 5-6 PINS 7-8
1 sec
(default)
2 sec
10 sec
20 sec
110 sec
220 sec
Open
Open
Short
Open
Open
Open
Open
Short
Short
Open
Short
Short
Open
Open
Short
Open
Open
Open
Open
Short
Open
Short
Open
Short
2
8
1
7
The watchdog timer is disabled after the system power-on. The
watchdog timer can be enabled by a Enable cycle with reading the
control port (443H), a Refresh cycle with reading the control port
(443H) and a Disable cycle by reading the watchdog timer disable
control port (043H). After a Enable cycle of WDT, user must constantly
proceed a Refresh cycle to WDT before its period setting comes ending
of every 1, 2, 10, 20, 110 or 220 seconds (Please reference to the
selection table of JP14 for WDT Time Out period setting). If the Refresh
cycle does not active before WDT period cycle, the onboard WDT
architecture will issue a Reset or NMI cycle to the system. The
watchdog timer controlled by two I/O ports.
443H
043H
I/O Read
I/O Read
Enable/Refresh cycle
Disable cycle
The following sample program shows how to Enable, Disable and
Refresh the watchdog timer:
WDT_EN_RF
WDT_DIS
EQU
EQU
WT_Enable
PUSH
MOV
IN
POP
POP
RET
0433H
0043H
PUSH
AX
DX
DX,WDT_EN_RF
AL,DX
DX
AX
; keep AX DX
; enable the WDT
; get back AX, DX
11
WT_Refresh
PUSH
MOV
IN
POP
POP
RET
WT_DISABLE
PUSH
MOV
IN
POP
POP
RET
3.7
PUSH
AX
DX
DX,WDT_ET_RF
AL,DX
DX
AX
PUSH
AX
DX
DX,WDT_DIS
AL,DX
DX
AX
; keep AX, DX
; refresh the WDT
; get back AX, DX
; disable the WDT
; get back AX, DX
VGA Controller
The onboard C&T 65545 CRT/Panel display controller provides up to
1024 x 768 at 16 colors resolution. The HS-3000/4M provides two
connection methods of CRT and Panel device. CN18 offers a 15-pin
CRT connector, and CN11 offers a 50-pin Panel connector.
CN18: CRT Connector (8x2 header)
PIN Description PIN Description
1
3
5
7
9
11
13
15
RED
BLUE
GND
GND
N/C
N/C
HSYNC
N/C
2
4
6
8
10
12
14
GREEN
N/C
GND
GND
GND
N/C
VSYNC
1
5
10
6
15
11
The HS-3000/4M provides a 44-pin 2.0mm pitch header connector
(CN11).
CN11: Panel Connector
CN11
Description
CN11
Description
1
3
5
7
9
11
+12V
GND
PVcc
FPVee
P0
P2
2
4
6
8
10
12
+12V
GND
PVcc
GND
P1
P3
…More on next page…
12
CN11
Description
CN11
Description
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
P4
P6
P8
P10
P12
P14
P16
P18
P20
P22
GND
SHFCLK
M
GND
GND
VCC
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
P5
P7
P9
P11
P13
P15
P17
P19
P21
P23
GND
FLM
LP
ENABKL
ASHFCLK
VCC
2
44
1
43
3.7.1 Connectors for Standard LCDs
Sharp LM64183P (640 x 480 DSTN MONO LCD)
Sharp LM64P83(CN1)
HS-3000/4M(CN11)
PIN
Description
PIN
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
S
CP1
CP2
DISP
VDD
VSS
VEE
DU0
DU1
DU2
DU3
DL0
DL1
DL2
DL3
36
38
35
5
6
3
12
11
10
9
16
15
14
13
FLM
LP
SHFCLK
+5V
+5V
GND
-17V (external power)
P3
P2
P1
P0
P7
P6
P5
P4
13
Sharp LM64C35P (640 x 480 DSTN STN Color)
Sharp LM64C35P(CN1)
HS-3000/4M(CN11)
PIN
Description
PIN
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
14
DL4
VSS
DL5
TD
DL6
LP
DL7
VSS
VSS
XCK
DL0
VCON
DL1
VDD
VSS
VDD
DL2
DISP
DL3
N/C
VSS
DU3
DU4
DU2
DU5
DU1
VSS
DU0
DU6
VSS
DU7
16
3
15
36
14
38
13
4
8
35
24
23
5
33
6
22
6
21
34
17
12
18
11
19
39
20
10
39
9
P7
GND
P6
FLM
P5
LP
P4
GND
GND
SLFCHK
P15
Contrast Adjust
P14
+5V
GND
+5V
P13
+5V
P12
GND
P8
P3
P9
P2
P10
GND
P11
P1
GND
P0
Sharp LM64C142(640 x 480 DSTN STN Color)
Sharp LM64C142(CN1)
HS-3000/4M(CN11)
PIN
Description
PIN
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
YD
LP
XCX
DISP
PVDD
PVSS
PVEE
DU0
DU1
DU2
DU3
DU4
DU5
DU6
DU7
Sharp LM64C142 (CN2)
PIN
Description
1
2
3
4
5
6
7
8
9
10
VSS
DL0
DL1
DL2
DL3
DL4
DL5
DL6
DL7
VSS
36
38
35
5
6
3
20
19
18
17
12
11
10
9
FLM
LP
SHFCLK
+5V
+5V
GND
+27V (external power)
P11
P10
P9
P8
P3
P2
P1
P0
HS-3000/4M(CN11)
PIN
Description
4
24
23
22
21
16
15
14
13
8
GND
P15
P14
P13
P12
P7
P6
P5
P4
GND
NEC NL8060AC26 (800 x 600 TFT Color)
NEC NL8060AC26(CN1)
PIN
Description
1
GND
2
Dot Clock
3
GND
4
HSYNC
5
HSYNC
6
GND
7
GND
HS-3000/4M(CN11)
PIN
Description
3
GND
35
SHFCLK
4
GND
38
LP
38
FLM
8
GND
8
GND
…More on next page…
15
NEC NL8060AC26(CN1)
PIN
Description
8
GND
9
R0
10
R1
11
R2
12
GND
13
R3
R4
14
15
R5
16
GND
17
GND
GND
18
19
G0
20
G1
21
G2
22
GND
23
G3
24
G4
G5
25
26
GND
27
GND
28
GND
B0
29
30
B1
31
B2
32
GND
33
B3
34
B4
35
B5
36
GND
37
DE
38
PVCC
39
PVCC
PVCC
40
41
MODE
16
HS-3000/4M(CN11)
PIN
Description
8
GND
27
P18
28
P19
29
P20
8
GND
30
P21
P22
31
32
P23
39
GND
39
GND
GND
39
19
P10
20
P11
21
P12
39
GND
22
P13
23
P14
P15
24
41
GND
41
GND
41
GND
P2
11
12
P3
13
P4
41
GND
14
P5
15
P6
16
P7
41
GND
37
M
43
PVCC
44
PVCC
PVCC
5
----
3.8
Serial Port Connectors
The HS-3000/4M’s CN17, 14, 15 and 16 provide four high speeds
NS16C550 compatible USRT with Read/Receive 16 byte FIFO serial
ports.
CN14, 15, 16: COM 2~COM 4 Connector (5x2 header)
PIN Description PIN Description
1
3
5
7
9
DCD
RXD
TXD
DTR
GND
2
4
6
8
10
DSR
RTX
CTX
RI
N/C
1
2
3
4
5
6
7
8
9
10
CN17: COM 1 Connector (DB9)
PIN Description PIN Description
1
2
3
4
5
DCD
RXD
TXD
DTR
GND
6
7
8
9
DSR
RTS
CTS
RI
5
9
1
6
JP1: COM 4 Use RS-232 or RS-422/485 Select
JP1
Description
Short
Open (default)
RS-232
RS-422/485
1
2
CN12: RS-422/485 Connector (5x2 header)
PIN Description PIN Description
1
3
5
7
9
TXRX+
GND
RTS+
CTS-
2
4
6
8
10
TX+
RXRTSCTS+
N/C
1
2
3
4
5
6
7
8
9
10
17
JP12: RS-422/485 Receiver Enabled/Disabled Select
JP12
Description
Short 1-2(default) Always Enable
Short 3-4
Enable by writing the REG.2EFh BIT1=1
All Open
Always Disable
2
6
1
5
JP13: RS-422/485 Transceiver Enabled/Disabled Select
JP13
Description
Short 1-2 (default)
Short 3-4
Short 5-6
Short 7-8
3.9
Always Enable
Enable by ”-RTS” signal
Enable by writing the REG.2EFh BIT0=1
Always Disable
2
8
1
7
Keyboard & Mouse Connector
The HS-3000/4M offers two connection methods for keyboard
connector, at location CN19 is 5-pin connector, location CN21 is PS/2
6-pin Mini DIN connector.
1
2
3
4
5
+5V
Keyboard Clock
Keyboard Data
N/C
GND
+5V
GND
1
2
3
4
5
N/C
Description
Keyboard
Data
PIN
Keyboard
Clock
CN19: 5-pin Keyboard Connector
CN21: PS/2 6-pin Mini DIN Keyboard Connector
18
PIN
Description
1
2
3
4
5
6
Keyboard Data
N/C
GND
+5V
Keyboard Clock
N/C
Keyboard
Clock
5
6
N/C
3 GND
Keyboard
1 Data
2 N/C
4 +5V
The HS-3000/4M has a PS/2 mouse connector onboard uses IRQ12. If
you do not use the PS/2 mouse and wish to assign IRQ12 for other
purposes, you may change JP8 do disconnect PS/2 interrupt from
IRQ12.
JP8: IRQ12 Enabled/Disabled Select
NOTE:
JP8
Description
Open
Short (default)
Disabled
Enabled
1
2
If you want to use PS/2 mouse, please make sure JP8 is Short.
CN20: PS/2 6-pin Mini DIN Mouse Connector
PIN
Description
1
2
3
4
5
6
Mouse Data
N/C
GND
+5V
Mouse Clock
N/C
Mouse
Clock
3 GND
5
Mouse
1 Data
2 N/C
6
4 +5V
N/C
3.10 Speaker Connector
The HS-3000/4M has its own buzzer, and CN5 allows user to connect
to the external speaker.
CN5: Speaker Connector
PIN
Description
1
2
3
4
Speaker
N/C
GND
+5V
1
2
3
4
19
3.11 PCI E-IDE Drive Connector
One standard 40-pin header daisy-chain driver connector provides as
CN10 with following pin assignment. Total two IDE (Integrated Device
Electronics) drivers may connect.
CN10: IDE Connector
20
PIN
Description
PIN
Description
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
Reset
DATA 7
DATA 6
DATA 5
DATA 4
DATA 3
DATA 2
DATA 1
DATA 0
GND
N/C
IOW#
IOR#
N/C
N/C
Interrupt
SA1
SA0
HDC CS0
HDD Active
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
GND
DATA 8
DATA 9
DATA 10
DATA 11
DATA 12
DATA 13
DATA 14
DATA 15
N/C
GND
GND
GND
Bale – Default
GND - Default
IOCS16# - Default
N/C
SA2
HDC CS1#
GND
2
40
1
39
3.12 Parallel Connector
A standard 26-pin flat cable driver connector provides as CN2 with
following pin assignment for connection to parallel printer.
CN2: Parallel Connector
PIN
Description
PIN
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
STROBE
DATA 0
DATA 1
DATA 2
DATA 3
DATA 4
DATA 5
DATA 6
DATA 7
Acknowledge
Busy
Paper Empty
Printer Select
14
15
16
17
18
19
20
21
22
23
24
25
26
Auto Form Feed
ERROR#
Initialize
Printer Select LN#
GND
GND
GND
GND
GND
GND
GND
GND
GND
14
26
1
13
3.13 Power and LED Connectors
The following provides the pin information for CN1 4-pin power
connector, CN3 reset button connector, CN4 power LED and keylock
connector, and CN6 is IDE LED.
CN1: 4-pin Power Connector
PIN
Description
1
2
3
4
VCC
GND
GND
+12V
CN3: Reset Button Connector
PIN
Description
1
2
Reset Signal
GND
1
2
21
CN4: Keylock and Power LED Connector
1
2
3
4
5
Power LED
N/C
GND
Keylock
GND
1
2
3
4
5
Keylock
Description
Power LED
PIN
CN6: IDE LED Connector
PIN
Description
1
2
VCC
HDD Active
1
2
3.14 Floppy Disk Drive Connector
The HS-3000/4M uses a standard 34-pin header connector, CN7, for
floppy disk drive connection. A total of two FDD drives may be
connected at any given time.
CN7: Floppy Connector
22
PIN
Description
PIN
Description
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
N/C
GND
N/C
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
Reduce Write
N/C
N/C
Index#
MTR0#
DS1#
DS0#
MTR1#
Direction#
Step#
Write Data#
Write Gate#
Track 0#
Write Protect#
Read Data#
HDSEL#
Disk Change#
2
34
1
33
3.15 Flash ROM Type
The JP15 provides in selection the type of Flash ROM type. If VPP is
+5V please set 29C010, VPP is +12V please set 28F010.
JP15: Flash ROM Type Select
Options
Setting
29C010 (default)
28F010
Short 1-2
Short 2-3
1
3
3.16 System Memory
The HS-3000/4M has one SIMM socket, provides 72-pin SIMM
module. The memory access time should be 70ns or less. The
HS-3000/4M has one SIM socket and 4MB RAM onboard.
Memory Type Configuration
SM1
4MB RAM Onboard
BANK0
SM2
BANK1
Total
256K x 2
512K x 2
512K x 2
512K x 2
512K x 2
1M x 2
1M x 2
1M x 2
2M x 2
2M x 2
2M x 2
4M x 2
4M x 2
256K x 2
---512K x 2
1M x 2
4M x 2
---1M x 2
4M x 2
---2M x 2
4M x 2
---4M x 2
1M
1M
2M
3M
9M
2M
4M
10M
4M
8M
12M
8M
16M
3.17 PC/104 Bus Connection
The PC/104 expansion bus offers provisions to connect all types of
PC/104 modules. With the PC/104 bus being known as the new
generation of industrial embedded 16-bit PC standard bus, thousands
of PC/104 modules from multiple venders can be easily installed
onboard. The detailed pin assignment of the PC/104 expansion bus
connectors CN8 and CN9 are listed on the following tables.
23
NOTE: The PC/104 connector allows direct plugging or stack-through
piling of PC/104 modules without requiring the PC/104 mounting
kit.
CN8: PC/104 64-pin Connector
PIN
Description
PIN
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
IOCHECK*
SD7
SD6
SD5
SD4
SD3
SD2
SD1
SD0
IOCHRDY
AEN
SA19
SA18
SA17
SA16
SA15
SA14
SA13
SA12
SA11
SA10
SA9
SA8
SA7
SA6
SA5
SA4
SA3
SA2
SA1
SA0
GND
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
GND
RESETDRV
+5V
IRQ9
-5V
DRQ2
-12V
NOW*
+12V
GND
SMEMW*
SMEMR*
IOW*
IOR*
DACK3*
DRQ3
DACK1*
DRQ1
REFRESH*
SYSCLK
IRQ7
IRQ6
IRQ5
IRQ4
IRQ3
DACK2*
TC
BALE
+5V
OSC
GND
GND
2
1
24
64
63
CN9: PC/104 40-pin Connector
PIN
Description
PIN
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
GND
MEMCS16*
IOSC16*
IRQ10
IRQ11
MSDATA
IRQ15
IRQ14
DACK0*
DRQ0
DACK5*
DRQ5
DACK6*
DRQ6
DACK7*
DRQ7
+5V
MASTER*
GND
GND
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
GND
SBHE*
LA23
LA22
LA21
LA20
LA19
LA18
LA17
MEMR*
MEMW*
SD8
SD9
SD10
SD11
SD12
SD13
SD14
SD15
N/C
2
40
1
39
25
This page is intentionally left blank.
26
Chapter 4
AMI BIOS Setup
The HS-3200/4M uses Award ISA BIOS for the system configuration.
The AMI BIOS setup program is designed to provide the maximum
flexibility in configuring the system by offering various options that
could be selected for end-user requirements. This chapter is written to
assist you in the proper usage of these features.
4.1
Starting Setup
The Award BIOS is immediately activated when you first power on the
computer. The BIOS reads the system information contained in the
CMOS and begins the process of checking out the system and
configuring it. When it finishes, the BIOS will seek an operating system
on one of the disks and then launch and turn control over to the
operating system.
While the BIOS is in control, the Setup program can be activated in one
of two ways:
1.
By pressing <Del> immediately after switching the system on,
or
2.
By pressing the <Del> key when the following message
appears briefly at the bottom of the screen during the POST
(Power On Self Test).
Press DEL to enter SETUP.
If the message disappears before you respond and you still wish to
enter Setup, restart the system to try again by turning it OFF then ON or
pressing the "RESET" button on the system case. You may also restart
by simultaneously pressing <Ctrl>, <Alt>, and <Delete> keys. If you do
not press the keys at the correct time and the system does not boot, an
error message will be displayed and you will again be asked to...
PRESS F1 TO CONTINUE, DEL TO ENTER SETUP
27
4.2
Using Setup
In general, you use the arrow keys to highlight items, press <Enter> to
select, use the <PageUp> and <PageDown> keys to change entries,
press <F1> for help and press <Esc> to quit. The following table
provides more detail about how to navigate in the Setup program using
the keyboard.
Up arrow
Down arrow
Left arrow
Right arrow
Esc key
PgUp key
PgDn key
+ key
- key
F1 key
(Shift)F2 key
F3 key
F4 key
F5 key
F6 key
F7 key
F8 key
F9 key
F10 key
Move to previous item
Move to next item
Move to the item in the left hand
Move to the item in the right hand
Main Menu -- Quit and not save changes into CMOS
Status Page Setup Menu and Option Page Setup Menu -Exit current page and return to Main Menu
Increase the numeric value or make changes
Decrease the numeric value or make changes
Increase the numeric value or make changes
Decrease the numeric value or make changes
General help, only for Status Page Setup Menu and Option
Page Setup Menu
Change color from total 16 colors. F2 to select color
forward, (Shift) F2 to select color backward
Calendar, only for Status Page Setup Menu
Reserved
Restore the previous CMOS value from CMOS, only for
Option Page Setup Menu
Load the default CMOS value from BIOS default table, only
for Option Page Setup Menu
Load the default
Reserved
Reserved
Save all the CMOS changes, only for Main Menu
4.2.1 Getting Help
Press F1 to pop up a small help window that describes the appropriate
keys to use and the possible selections for the highlighted item. To exit
the Help Window press <Esc> or the F1 key again.
28
4.3
Main Menu
Once you enter the Award BIOS CMOS Setup Utility, the Main Menu
will appear on the screen. The Main Menu allows you to select from
several setup functions and two exit choices. Use the arrow keys to
select among the items and press <Enter> to enter the sub-menu.
AMI BIOS Setup Utility – Version 1.23
© 1999 American Megatrends, Inc. All Rights Reserved
STANDARD CMOS SETUP
Advanced CMOS Setup
Advanced Chipset Setup
PCI / Plug and Play Setup
Peripheral Setup
Auto-Detect Hard Disks
Change User Password
Change Language Setting
Auto Configuration with Optional Settings
Auto Configuration with Fail Safe Settings
Save Settings and Exit
Exit Without Saving
Load configuration settings giving highest performance
Esc: Exit
: Sel F2/F3: Color F10: Save & Exit
29
4.4
Standard CMOS Setup
The Standard Setup is used for the basic hardware system
configuration. The main function is for Data/Time and Floppy/Hard Disk
Drive settings. Please refer to the following screen for the setup. When
the IDE hard disk drive you are using is larger than 528MB, please set
the HDD mode to LBA mode. Please use the IDE Setup Utility in BIOS
SETUP to install the HDD correctly.
AMI BIOS Setup – Standard CMOS Setup
© 1999 American Megatrends, Inc. All Rights Reserved
Data (mm:dd:yy):Fri, Dec 20 2002
Base Memory: 640 KB
Time (hh:mm:ss):14:50:1
Ext Memory: 3 MB
Type
Auto
Auto
CYLS HEAD PRECOMP LANDZ
Pri Master
Pri Slave
:
:
Floppy Drive A
Floppy Drive B
: 1.44 MB 3.5
: Not Installed
Boot Sector Virus Protection:
Month: Jan – Dec
Day: 01 – 31
Year: 1901 – 2099
30
SECTOR MODE
Off
Off
Disabled
ESC: Quit
: Sel
PgUp/PgDn: Modify
F1: Help F2/F3: Color
4.5
Advanced CMOS Setup
This section allows you to configure your system for the basic
operation. You have the opportunity to select the system’s default
speed, boot-up sequence, keyboard operation, shadowing and
security.
AMIBIOS SETUP – ADVANCED CMOS SETUP
(C)2001 American Megatrends, Inc. All Rights Reserved
Quick Boot
1st Boot Device
2nd Boot Device
3rd Boot Device
Try Other Boot Devices
BootUp Num-Lock
Floppy Drive Swap
Floppy Drive Seek
PS/2 Mouse Support
System Keyboard
Primary Display
Password Check
Wait For ‘F1’ If Error
C000, 32k Shadow
C800, 32k Shadow
D000, 32k Shadow
D800, 32k Shadow
Disabled
IDE-0
Floppy
Disabled
Yes
On
Disabled
Disabled
Enabled
Present
VGA/EGA
Setup
Enabled
Disabled
Disabled
Disabled
Disabled
Available Options:
` Disabled
Enabled
ESC:Exit
:Sel
PgUp/PgDn: Modify
F1:Help
F2/F3:Color
31
4.6
Advanced Chipset Setup
This section allows you to configure the system based on the specific
features of the installed chipset. This chipset manages bus speeds and
the access to the system memory resources, such as DRAM and the
external cache. It also coordinates the communications between the
conventional ISA and PCI buses. It must be stated that these items
should never be altered. The default settings have been chosen
because they provide the best operating conditions for your system.
You might consider and make any changes only if you discover that the
data has been lost while using your system.
AMIBIOS SETUP – ADVANCED CHIPSET SETUP
(C)1999 American Megatrends, Inc. All Rights Reserved
AT Bus Clock
Slow Refresh (us)
Memory Hole At 15-16M
RAS Precharge time
RAS Active Time Insert Wait
CAS Precharge Time Insert Wait
Memory Write Insert Wait
Memory Miss Read Insert Wait
ISA Write cycle end Insert Wait
I/O Recovery
I/O Recovery Period
On-Chip I/O Recovery
16Bit ISA Insert Wait
14.318/2
120
Disabled
3.5T
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
0.75 us
Disabled
Enabled
Available Options:
` Disabled
Enabled
ESC:Exit
:Sel
PgUp/PgDn: Modify
F1:Help
F2/F3:Color
32
4.7
PCI / Plug And Play Setup
This section describes configuring the PCI bus system. PCI, or
Personal Computer Interconnect, is a system that allows I/O devices to
operate at speeds nearing the speed the CPU itself uses when
communicating with its own special components. This section covers
some very technical items and it is strongly recommended that only
experienced users should make any changes to the default settings.
AMIBIOS SETUP – PCI / PLUG AND PLAY SETUP
(C)1999 American Megatrends, Inc. All Rights Reserved
Plug and Play Aware O/S
DMA Channel 0
DMA Channel 1
DMA Channel 3
DMA Channel 5
DMA Channel 6
DMA Channel 7
IRQ3
IRQ4
IRQ7
IRQ9
IRQ10
IRQ11
IRQ14
IRQ15
No
PnP
PnP
PnP
PnP
PnP
PnP
PnP
PnP
PnP
PnP
PnP
PnP
PnP
PnP
Available Options:
` No
Yes
ESC:Exit
:Sel
PgUp/PgDn: Modify
F1:Help
F2/F3:Color
33
4.8
Peripheral Setup
The IDE hard drive controllers can support up to two separate hard
drives. These drives have a master/slave relationship that is
determined by the cabling configuration used to attach them to the
controller. Your system supports two IDE controllers--a primary and a
secondary--so you can install up to four separate hard disks.
PIO means Programmed Input/Output. Rather than having the BIOS
issue a series of commands to affect the transfer to or from the disk
drive, PIO allows the BIOS to tell the controller what it wants and then
let the controller and the CPU perform the complete task by them. This
is much simpler and more efficient (also faster).
AMIBIOS SETUP – PERIPHERAL SETUP
(C)1999 American Megatrends, Inc. All Rights Reserved
OnBoard IDE
OnBoard FDC
OnBoard Serial Port 1
OnBoard Serial Port 2
Serial Port2 Mode
Receiver Polarity
Transmitter Polarity
OnBoard Serial Port3
Serial Port3 IRQ
OnBoard Serial Port4
Serial Port4 Mode
Serial Port4 IRQ
Receiver Polarity
Transmitter Polarity
OnBoard Prarllel Port
Parallel Port Mode
EPP Version
Parallel Port IRQ
Parallel Port DMA Channel
34
Primary
Auto
Auto
Auto
Normal
Non-Inverted
Non-Inverted
Audo
Auto
Auto
Normal
Auto
Non-Inverted
Non-Inverted
Auto
ECP
N/A
Auto
Auto
Available Options:
` Disabled
Primary
Secondary
Both
ESC:Exit
:Sel
PgUp/PgDn: Modify
F1:Help
F2/F3:Color
4.9
Auto-Detect Hard Disks
This option detects the parameters of an IDE hard disk drive, and
automatically enters them into the Standard CMOS Setup screen.
Up to four IDE drives can be detected, with parameters for each
appearing in sequence inside a box. To accept the displayed entries,
press the “Y” key; to skip to the next drive, press the “N” key. If you
accept the values, the parameters will appear listed beside the drive
letter on the screen.
AMIBIOS SETUP – PERIPHERAL SETUP
(C)1999 American Megatrends, Inc. All Rights Reserved
Standard CMOS Setup
Advanced CMOS Setup
Advanced Chipset Setup
Power Management Setup
PCI / Plug and Play Setup
Peripheral Setup
Hardware Monitor Setup
Auto-Detect Hard Disks
Change User Password
Change Supervisor Password
Auto Configuration with Optimal Settings
Auto Configuration with Fail Safe Settings
Save Settings and Exit
Exit Without Saving
Standard CMOS setup for changing time, date, hard disk type, etc.
ESC:Exit
:Sel F2/F3: Color F10: Save & Exit
35
4.10 Change Supervisor/User Password
AMIBIOS SETUP – PERIPHERAL SETUP
(C)1999 American Megatrends, Inc. All Rights Reserved
Standard CMOS Setup
Advanced CMOS Setup
Advanced Chipset Setup
Power Management Setup
Enter new supervisor password: _
Change Supervisor Password
Auto Configuration with Optimal Settings
Auto Configuration with Fail Safe Settings
Save Settings and Exit
Exit Without Saving
Standard CMOS setup for changing time, date, hard disk type, etc.
ESC:Exit
:Sel F2/F3: Color F10: Save & Exit
You can set either supervisor or user password, or both of then. The
differences between are:
supervisor password: can enter and change the options of the setup
menus.
user password: just can only enter but do not have the right to change the
options of the setup menus.
When you select this function, the following message will appear at the
center of the screen to assist you in creating a password.
ENTER PASSWORD:
Type the password, up to eight characters in length, and press
<Enter>. The password typed now will clear any previously entered
password from CMOS memory. You will be asked to confirm the
password. Type the password again and press <Enter>. You may also
press <Esc> to abort the selection and not enter a password.
To disable a password, just press <Enter> when you are prompted to
enter the password. A message will confirm the password will be
disabled. Once the password is disabled, the system will boot and you
can enter Setup freely.
PASSWORD DISABLED.
When a password has been enabled, you will be prompted to enter it
every time you try to enter Setup. This prevents an unauthorized
36
person from changing any part of your system configuration.
Additionally, when a password is enabled, you can also require the
BIOS to request a password every time your system is rebooted. This
would prevent unauthorized use of your computer.
You determine when the password is required within the BIOS
Features Setup Menu and its Security option (see Section 3). If the
Security option is set to “System”, the password will be required both at
boot and at entry to Setup. If set to “Setup”, prompting only occurs
when trying to enter Setup.
4.11 Auto Configuration with Optimal
Settings
When you press <Enter> on this item you will get a confirmation dialog
box with a message shown below. This option allows you to
load/restore the BIOS default values permanently stored in the BIOS
ROM. Pressing ‘Y’ loads the BIOS default values for the most stable,
minimal-performance system operations.
AMIBIOS SETUP – PERIPHERAL SETUP
(C)1999 American Megatrends, Inc. All Rights Reserved
Standard CMOS Setup
Advanced CMOS Setup
Advanced Chipset Setup
Power Management Setup
Load high performance settings (Y/N) ? N
Change Supervisor Password
Auto Configuration with Optimal Settings
Auto Configuration with Fail Safe Settings
Save Settings and Exit
Exit Without Saving
Standard CMOS setup for changing time, date, hard disk type, etc.
ESC:Exit
:Sel F2/F3: Color F10: Save & Exit
37
4.12 Auto Configuration with Fail Safe
Settings
When you press <Enter> on this item you get a confirmation dialog box
with a message similar to the figure below. This option allows you to
load/restore the default values to your system configuration, optimizing
and enabling all high performance features. Pressing ‘Y’ loads the
default values that are factory settings for optimal performance system
operations.
AMIBIOS SETUP – PERIPHERAL SETUP
(C)1999 American Megatrends, Inc. All Rights Reserved
Standard CMOS Setup
Advanced CMOS Setup
Advanced Chipset Setup
Power Management Setup
Load failsafe settings (Y/N) ? N
Change Supervisor Password
Auto Configuration with Optimal Settings
Auto Configuration with Fail Safe Settings
Save Settings and Exit
Exit Without Saving
Standard CMOS setup for changing time, date, hard disk type, etc.
ESC:Exit
:Sel F2/F3: Color F10: Save & Exit
38
4.13 Save Settings and Exit
Pressing <Enter> on this item asks for confirmation:
AMIBIOS SETUP – PERIPHERAL SETUP
(C)1999 American Megatrends, Inc. All Rights Reserved
Standard CMOS Setup
Advanced CMOS Setup
Advanced Chipset Setup
Power Management Setup
Save current settings and exit (Y/N) ? Y
Change Supervisor Password
Auto Configuration with Optimal Settings
Auto Configuration with Fail Safe Settings
Save Settings and Exit
Exit Without Saving
Standard CMOS setup for changing time, date, hard disk type, etc.
ESC:Exit
:Sel F2/F3: Color F10: Save & Exit
Pressing “Y” stores the selections made in the menus in CMOS – a
special section of memory that stays on after you turn your system off.
The next time you boot your computer, the BIOS configures your
system according to the Setup selections stored in CMOS. After saving
the values the system is restarted again.
39
4.14 Exit Without Saving
Pressing <Enter> on this item asks for confirmation:
Quit without saving (Y/N)? Y
This allows you to exit Setup without storing in CMOS any change. The
previous selections remain in effect. This exits the Setup utility and
restarts your computer.
AMIBIOS SETUP – PERIPHERAL SETUP
(C)1999 American Megatrends, Inc. All Rights Reserved
Standard CMOS Setup
Advanced CMOS Setup
Advanced Chipset Setup
Power Management Setup
Quit without saving (Y/N) ? N
Change Supervisor Password
Auto Configuration with Optimal Settings
Auto Configuration with Fail Safe Settings
Save Settings and Exit
Exit Without Saving
Standard CMOS setup for changing time, date, hard disk type, etc.
ESC:Exit
:Sel F2/F3: Color F10: Save & Exit
Abandon all Data & Exit Setup
40
Download PDF

advertising