Casio | Watch 3223 | User's Manual | Casio Watch 3223 User's Manual

MO1104-EA
Operation Guide 3216 3223
Keep the watch exposed to bright light
Warning!
• The measurement functions built into this watch are not intended for taking
measurements that require professional or industrial precision. Values produced
by this watch should be considered as reasonable representations only.
• The Moon phase indicator and tide graph data that appear on the display of this
watch are not intended for navigation purposes. Always use proper instruments
and resources to obtain data for navigation purposes.
• This watch is not an instrument for calculating low tide and high tide times. The
tide graph of this watch is intended to provide a reasonable approximation of
tidal movements only.
• Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any
damage or loss suffered by you or any third party arising through the use of this
product or its malfunction.
l
Bright Light
Solar cell
l
Congratulations upon your selection of this CASIO watch. To get the most out of your
purchase, be sure to read this manual carefully.
• Be sure to keep all user documentation handy for future reference.
l l l l l l l l l
Getting Acquainted
The electricity generated by the solar cell of the watch is
stored by a rechargeable battery. Leaving or using the
watch where it is not exposed to light causes the battery
to run down. Make sure the watch is exposed to light as
much as possible.
• When you are not wearing the watch on your wrist,
position the face so it is pointed at a source of bright
light.
• You should try to keep the watch outside of your sleeve
as much as possible. Charging is reduced significantly if
the face is covered only partially.
E-1
E
• The watch continues to operate, even when it is not exposed to light. Leaving the
watch in the dark can cause the battery to run down, which will result in some watch
functions to be disabled. If the battery goes dead, you will have to re-configure watch
settings after recharging. To ensure normal watch operation, be sure to keep it
exposed to light as much as possible.
Battery charges in the light.
Solar cell
(Converts light to
electrical power.)
Battery discharges in the dark.
Bright Light
Electrical
energy
LEVEL 1
LEVEL 2
All
functions
enabled
• The actual level at which some functions are disabled depends on the watch model.
• Frequent display illumination can run down the battery quickly and require charging.
• Be sure to read “Power Supply” (page E-41) for important information you
need to know when exposing the watch to bright light.
If the display of the watch is blank...
If the display of the watch is blank, it means that the watch’s Power Saving function
has turned off the display to conserve power.
• See “Power Saving Function” (page E-59) for more information.
LEVEL 1
LEVEL 2
LEVEL 3
Dis- LEVEL 3
charge LEVEL 4
Charge LEVEL 4
Some or all
functions
disabled
Rechargeable battery
E-2
E-3
About This Manual
ll l
ll l
ll l
Module 3216
lll
ll l
ll l
lll
ll l
ll l
ll l
lll
ll l
ll l
ll l
ll l
lll
• Depending on the model of your watch, display text appears either as dark figures
on a light background (Module 3216), or light figures on a dark background (Module
3223). All of the illustrations in this manual show Module 3216.
• Button operations are indicated using the letters shown in the illustration.
• Each section of this manual provides you with the information you need to perform
operations in each mode. Further details and technical information can be found in
the “Reference” section.
Contents
General Guide ......................................................................................................... E-8
Timekeeping .......................................................................................................... E-10
Tide/Moon Data ..................................................................................................... E-16
World Time ............................................................................................................. E-23
Alarms .................................................................................................................... E-26
Stopwatch .............................................................................................................. E-31
Countdown Timer .................................................................................................. E-33
Illumination ............................................................................................................ E-37
Power Supply ........................................................................................................ E-41
Tide Site Name ...................................................................................................... E-49
Reference .............................................................................................................. E-52
Specifications ....................................................................................................... E-65
Module 3223
E-4
E-5
Procedure Lookup
To turn the Hourly Time Signal on and off .......................................................... E-30
The following is a handy reference list of all the operational procedures contained in
this manual.
To set the time and date ....................................................................................... E-11
To change the Daylight Saving Time (summer time) setting ............................ E-15
To adjust the high tide time ................................................................................. E-20
To measure times with the stopwatch ................................................................ E-32
To configure the countdown timer ...................................................................... E-34
To use the countdown timer ................................................................................ E-36
To illuminate the display manually ...................................................................... E-37
To reverse the displayed Moon phase ................................................................ E-22
To specify the illumination duration ................................................................... E-38
To view the time in another city ........................................................................... E-24
To turn the auto light switch on and off .............................................................. E-40
To toggle a city code time between Standard Time and
Daylight Saving Time ...................................................................................... E-25
To turn the button operation tone on and off ..................................................... E-58
To set an alarm time ............................................................................................. E-27
To recover from the sleep state ........................................................................... E-60
To test the alarm ................................................................................................... E-28
To turn Power Saving on and off ......................................................................... E-60
To configure tide site settings ............................................................................. E-49
To turn an alarm on and off .................................................................................. E-29
E-6
E-7
World Time Mode
General Guide
lllll
Stopwatch Mode
▲
lllll
l
ll
ll
▲
llll
llll
▲
ll
lllll
lll
Countdown Timer Mode
l
lll
ll
▲
lll
lll
lll
l
lll
lll
Press C.
lll
ll
E-8
llll
▲
Tide/Moon Data Mode
Timekeeping Mode
lll
Alarm Mode
ll
▲
• Press C to change from mode to mode.
• In any mode (except when a setting screen is on the display), press B to illuminate
the display.
• When you return to the Timekeeping Mode, the day of the week will be displayed
after the name of the site you selected. See “Tide Site Name List” (page L-2) for
more information about the site.
E-9
Operation Guide 3216 3223
To set the time and date
Timekeeping
This watch is preset with a number of city codes, each of
which represents the time zone where that city is located.
When setting the time, it is important that you first select
the correct city code for your Home City (the city where
you normally use the watch). If your location is not
included in the preset city codes, select the preset city
code that is in the same time zone as your location.
• Note that all of the times for the World Time Mode city
codes (page E-23) are displayed in accordance with the
time and date settings you configure in the Timekeeping
Mode.
A
lll
lll
ll l
ll l
▲
lll
ll l
ll l
ll l
ll l
lll
Site name
ll l
lll
lllll
ll l
ll l
Read This Before You Set the Time and Date!
Hour : Minutes
Seconds
PM indicator
▲
ll lll
lll
Press the A button to view the current site name setting.
Day of week Month – Day Use the Timekeeping Mode to set and view the current
ll l
ll l
time and date.
Current Time
1. In the Timekeeping Mode hold down A until the city
code starts to flash, which indicates the setting screen.
2. Use D and B to select the city code you want.
• Make sure you select your Home City code before
changing any other setting.
• For full information on city codes, see the “City Code
Table” at the back of this manual.
3. Press C to move the flashing in the sequence shown below to select the other
settings.
DST
City Code
12/24-Hour
Format
Illumination
Duration
Power Saving
Seconds
Button
Operation Tone
Minutes
Hour
Day
Month
Year
ll l
E-10
E-11
• The following steps explain how to configure timekeeping settings only.
4. When the timekeeping setting you want to change is flashing, use D or B to
change it as described below.
Screen:
To do this:
Change the city code
Toggle between Daylight Saving Time
(
) and Standard Time (
).
Toggle between 12-hour (
) and 24hour (
) timekeeping
Reset the seconds to
Change the hour and minutes
Screen:
Do this:
Use D (east) and B
(west).
Press D.
To do this:
Change the year, month, or day
Toggle the button operation tone between Press D.
(on) and
(off)
Toggle the illumination duration between
Press D.
(approximately 1.5 seconds) and
(approximately 3 seconds).
Toggle between Power Saving on ( ) and Press D.
off (
)
/
Press D.
Press D.
Use D (+) and B (–).
Do this:
Use D (+) and B (–).
5. Press A to exit the setting screen.
• The day of the week is displayed automatically in accordance with the date (year,
month, and day) settings.
E-12
E-13
ll
ll
lll l l ll
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
ll
Daylight Saving Time (DST)
To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down A until the city
code starts to flash, which indicates the setting screen.
lll llll
2.
Press C and the DST setting screen appears.
l
ll ll
3. Use D to toggle the DST settings in the sequence
shown below.
ll
• With the 12-hour format, the P (PM) indicator appears to the left of the hour digits for
times in the range of noon to 11:59 p.m. and no indicator appears to the left of the
hour digits for times in the range of midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all other modes.
lllll
12-hour and 24-hour timekeeping
DST indicator
)
DST on (
)
4. When the setting you want is selected, press A twice to exit the setting screen.
• The DST indicator appears to indicate that Daylight Saving Time is turned on.
E-14
E-15
Tide Data
Tide/Moon Data
In the Tide/Moon Data Mode, you can see the tide for the tide site you selected at
specified time and the current date’s moon phase for your Home City. You can specify
a date and view tide and moon data for that date.
• See “Moon Phase Indicator” (page E-52) for information about the moon phase
indicator and “Tide Graph” (page E-56) for information about the tide graph.
• All of the operations in this section are performed in the Tide/Moon Data Mode
(page E-8).
Note
• It takes about two seconds to calculate tide graph data. You will not be able to
display a setting screen while data calculation is in progress.
• Moon age is calculated to an accuracy of ±1 day.
• You can view the current tide and moon age graph in the Timekeeping Mode (page
E-10).
The Tide Graph that appears first when you enter the Tide/Moon Data Mode shows
the data at 6:00 a.m. for your currently selected tide site on the current date, according
to the Timekeeping Mode. From there you can specify another time on the same date.
• If the tide data is not correct, check your Timekeeping Mode settings and correct them
if necessary. See “To configure tide site settings” (page E-49) for more information.
• If you feel that the information shown by the Tide Graph is different from actual tide
conditions, you need to adjust the high tide time. See “Adjusting the High Tide Time”
(page E-19) for more information.
Moon Data
The moon phase and moon age information that appears first when you enter the
Tide/Moon Data Mode shows the data at noon for your currently selected Home City
on the current date, according to the Timekeeping Mode. After that you can specify
another date to view data.
• If the moon data is not correct, check your Timekeeping Mode settings and correct
them if necessary.
• If the moon phase indicator shows a phase that is a mirror image of the actual moon
phase in your area, you can use the procedure under “Reversing the Displayed
Moon Phase” (page E-21) to change it.
E-16
E-17
Tide/Moon Data Screens
In the Tide/Moon Data Mode, press A to toggle between the tide data screen and the
moon data screen.
Tide Data Screen
Moon Data Screen
Current tide level
▲
Month – Day
Press A.
Use the following procedure to adjust the high tide time within a particular date. You
can find out high tide information for your area from a tide table, the Internet, or your
local newspaper.
▲
ll l
Time
Moon phase
• When you display the Tide Data Screen, it initially shows tide data for 6:00 a.m.
• Use the Tide Data Screen to specify the Tide Data time. You can use D to change
the displayed time in one-hour increments. The Tide Data time is scrolled within the
current date only. Scrolling past midnight does not change the date.
• Use the Moon Data Screen to specify the Tide/Moon Data date. You can use D to
change the displayed date in one-day increments. Pressing D will display the year
of the displayed date.
Adjusting the High Tide Time
lll
l ll
ll l
Current tide range
E-18
DST off (
Moon age
Month – Day
E-19
Operation Guide 3216 3223
l ll l
llll
To adjust the high tide time
1. In the Tide/Moon Data Mode, use A to display the
Moon Data Screen (page E-18).
lll
2. Use D to scroll the date until one whose high tide time
you want to change is displayed.
lll
3. Hold down A until the hour digits start to flash.
4. Use D (+) and B (–) to change the hour setting.
5. When the hour is the setting you want, press C.
• This will cause the minute digits to flash.
Hour
6. Use D (+) and B (–) to change the minute setting.
7. When the minute setting is the way you want, press A
lll
to exit the adjustment screen and return to the Tide/
Moon Data Mode screen.
ll
lll ll
• Pressing D and B at the same time while the time
adjustment screen is displayed (steps 4 through 7
above) will return the high tide time to its initial factory
default setting.
Minute
• The high tide time setting is affected by the DST
(summer time) setting of the Timekeeping Mode.
lll lll
llll
l ll l
ll l
llll
lll l l l l
Reversing the Displayed Moon Phase
The left-right (east-west) appearance of the Moon depends on whether the Moon is
north of you (northerly view) or south of you (southerly view) as you view it.
You can use the procedure below to reverse the displayed Moon phase so it matches
the actual appearance of the Moon where you are located.
• To determine the viewing direction of the Moon, use a compass to take a direction
reading of the Moon at its meridian passage.
• For information about the Moon phase indicator, see “Moon Phase Indicator” (page
E-52).
llll
llllll
ll
llllll
• On some days, there are two high tides. With this watch, you can adjust the first high
tide time only. The second high tide time for that day is adjusted automatically based
on the first high tide time.
l llll
E-20
E-21
lll
llll
lll
lll
llll
To reverse the displayed Moon phase
1. In the Tide/Moon Data Mode, hold down A until the
llll
hour digits start to flash.
ll l
2. Press C twice.
• This will cause the Moon phase indicator to flash. This
is the indicator switching screen.
3. Press D to toggle the Moon phase indicator between
the southerly view (indicated by
) and northerly
view (indicated by
).
• Northerly view: Moon is north of you.
• Southerly view: Moon is south of you.
4. When the Moon phase indicator setting is the way you
want, press A to exit the switching screen and return
to the Tide/Moon Data Mode screen.
World Time
City code
Current time in
selected city
World Time shows the current time in 48 cities (31 time
zones) around the world.
• The times kept in the World Time Mode are
synchronized with the time being kept in the
Timekeeping Mode. If you feel that there is an error in
any World Time Mode time, check to make sure you
have the correct city selected as your Home City. Also
check to make sure that the current time as shown in
the Timekeeping Mode is correct.
• Select a city code in the World Time Mode to display the
current time in any particular time zone around the
globe. See the “City Code Table” at the back of this
manual for information about the UTC differential
settings that are supported.
• All of the operations in this section are performed in the
World Time Mode, which you enter by pressing C
(page E-9).
ll
E-22
E-23
To view the time in another city
While in the World Time Mode, press D (eastward) to scroll through the city codes
(time zones).
• Pressing the D and B at the same time will jump to the UTC time zone.
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, press D to display the city
code (time zone) whose Standard Time/Daylight Saving
Time setting you want to change.
2. Hold down A to toggle between Daylight Saving Time
(DST indicator displayed) and Standard Time (DST
indicator not displayed).
• The DST indicator is shown on the World Time Mode
screen while Daylight Saving Time is turned on.
DST indicator
• Note that the Standard Time/Daylight Saving Time
setting affects only the currently displayed city code.
Other city codes are not affected.
• Note that you cannot switch between Standard Time
and Daylight Saving Time while UTC is selected as the
city code.
E-24
E-25
To set an alarm time
ll ll
llll
ll
ll
Alarm time
(Hour : Minutes)
ll ll
ll
llll
Alarm number
The Alarm Mode gives you a choice of four one-time
alarms and one snooze alarm.
Also use the Alarm Mode to turn the Hourly Time Signal
(SIG) on and off.
• There are five alarm screens numbered AL1, AL2,
AL3 and AL4 for the one-time alarm, and a snooze
alarm screen indicated by SNZ. The Hourly Time
Signal screen is indicated by SIG.
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C (page
E-9).
• To set a one-time alarm, display alarm screen AL1, AL2, AL3 or AL4.
To set the snooze alarm, display the SNZ screen.
• The snooze alarm repeats every five minutes.
2. After you select an alarm, hold down A until the hour setting of the alarm time
starts to flash, which indicates the setting screen.
• This operation turns on the alarm automatically.
3. Press C to move the flashing between the hour and minute settings.
4. While a setting is flashing, use D (+) and B (–) to change it.
• With the 12-hour format, set the time correctly as a.m. or p.m. (P indicator).
5. Press A to exit the setting screen.
E-26
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
E-28
ll ll
To turn an alarm on and off
1. In the Alarm Mode, use D to select an alarm.
2. Press A to toggle it on and off.
•
Turning on a alarm (AL1, AL2, AL3, AL4 or
ll
SNZ) displays the alarm on indicator on its Alarm Mode
screen.
• In all modes, the alarm on indicator is shown for any
alarm that currently is turned on.
• The alarm on indicator flashes while the alarm is
ON
Snooze alarm
sounding.
indicator
• The snooze alarm indicator flashes while the snooze
Alarm on indicator
alarm is sounding and during the 5-minute intervals
between alarms.
llll
The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, until you turn the alarm off (page E-29).
• Alarm and Hourly Time Signal operations are performed in accordance with the
Timekeeping Mode time.
• To stop the alarm tone after it starts to sound, press any button.
• Performing any one of the operations below during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen (page E-11)
Displaying the SNZ setting screen (page E-27)
E-27
ll
Alarm Operation
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
ll
Alarms
E-29
Operation Guide 3216 3223
ll ll
Stopwatch
The stopwatch lets you measure elapsed time, split times,
and two finishes.
• The display range of the stopwatch is 59 minutes, 59.99
seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
• Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C (page
E-9).
llll
To turn the Hourly Time Signal on and off
1. In the Alarm Mode, use D to select the Hourly Time
Signal (SIG).
ll
2. Press A to toggle it on and off.
• The Hourly Time Signal on indicator is shown on the
display in all modes while this function is turned on.
ll
llll
lllll
ll
l
Hourly time signal
on indicator
Seconds
1/100 second
Minutes
E-30
E-31
To measure times with the stopwatch
Elapsed Time
D
Start
Split Time
D
Countdown Timer
➤D
Stop
➤D
Re-start
➤D
Stop
➤A
Clear
➤A
Split
(SPL displayed)
➤A
Split release
➤D
Stop
➤A
Clear
➤A
Split release
Display time of
second runner.
➤A
Clear
Dual timers can be set with two different starting times.
The watch can be configured so the two timers alternate,
so when one reaches the end of its countdown, the other
timer starts. You can specify a “number of repeats” value,
which controls how many times the two-timer countdown
operation is performed (1 = once, 2 = twice, etc.). The
starting time of each timer can be set in five-second steps
up to 99 minutes, 55 seconds.
You can specify up to 10 repeats. The watch emits a short
beep whenever either of the timers reaches the end of its
countdown during an ongoing timer operation. The watch
emits a 5-second beep when the end of the final timer
operation (specified by the number of repeats) is reached.
Number of Repeats
➤A
➤D
Split
Stop
First runner finishes. Second runner
Display time of first finishes.
runner.
Start
l
Two Finishes
D
llll
Start
lllll
ll
Minutes
Seconds
Timer 1
Countdown End Beeper
The countdown end beeper lets you know when the countdown reaches zero. The
beeper stops after about 5 seconds or when you press any button.
E-32
llll
lllll
To configure the countdown timer
1.While the countdown start time is on the display in the
Countdown Timer Mode, hold down A until the current
countdown start time starts to flash, which indicates the
ll
l
l
setting screen.
l
l
l
• If the countdown start time is not displayed, use the
procedure under “To use the countdown timer” (page
E-36) to display it.
2. Press C to move the flashing in the sequence shown
below to select other settings.
Setting
Minutes, Seconds
Screen
l
llll
llll
3. When the setting you want to change is flashing, use D and B to change it as
described below.
Button Operation
Use D (+) and B (–) to change the setting.
Use D (+) and B (–) to change the setting.
Number of Repeats
• To disable either timer, set 00'00" as its countdown start time.
4. Press A to exit the setting screen.
llll
E-34
E-35
To use the countdown timer
Illumination
ll l
lllll
ll l
ll l
ll l
llll
l
Current timer time
Current time
ll l
ll
lll
(Reset)
lll
Present number of repeats
ll l
Current repeat count
(Start/Stop)
Timer 1 or 2
Press D while in the Countdown Timer Mode to start the countdown timer.
• The countdown is performed by alternating between Timer 1 and Timer 2. A short
beep is emitted to signal a changeover from one timer to the other.
• Pressing A while a countdown timer is stopped resets it to the start time specified by you.
• Press D to pause a countdown. Press D again to resume.
• The watch emits a 5-second beep when the end of the final timer operation
(specified by the number of repeats) is reached.
• Even if you exit the Countdown Timer Mode, the countdown timer operation
continues and the watch beeps as required.
• To stop a countdown operation completely, first pause it (by pressing D), and then
press A. This returns the countdown time to its starting value.
Auto light switch on
indicator
This watch has an EL (electro-luminescent) panel that
causes the entire display to glow for easy reading in the
dark. The watch’s auto light switch turns on illumination
automatically when you angle the watch towards your
face.
• The auto light switch must be turned on (indicated by
the auto light switch on indicator) for it to operate.
• See “Illumination Precautions” (page E-63) for other
important information about using illumination.
To illuminate the display manually
In any mode (except when a setting screen is on the
display), press B to turn on illumination.
• The above operation turns on illumination regardless of
the current auto light switch setting.
E-36
E-37
• You can use the procedure below to select either 1.5 seconds or 3 seconds as the
illumination duration. When you press B, the illumination will remain on for about
1.5 seconds or 3 seconds, depending on the current illumination duration setting.
lll
l ll
To specify the illumination duration
1. In the Timekeeping Mode, hold down A until the
display contents start to flash. This is the setting screen.
2. Press C 10 times until the current illumination duration
llll
or
) appears.
setting (
3. Press D to toggle the setting between
(approximately 1.5 seconds) and
(approximately
3 seconds).
4. Press A to exit the setting screen.
llll
E-38
E-33
About the Auto Light Switch
Turning on the auto light switch causes illumination to turn on, whenever you position
your wrist as described below in any mode. Note that this watch features a “Full Auto
EL Light”, so the auto light switch operates only when available light is below a certain
level. It does not turn on the backlight under bright light.
Moving the watch to a position that is parallel to the ground and then tilting it towards
you more than 40 degrees causes illumination to turn on.
• Wear the watch on the outside of your wrist.
Parallel to
ground
More than 40°
E-39
Operation Guide 3216 3223
Warning!
• Always make sure you are in a safe place whenever you are reading the
display of the watch using the auto light switch. Be especially careful when
running or engaged in any other activity that can result in accident or injury.
Also take care that sudden illumination by the auto light switch does not
startle or distract others around you.
• When you are wearing the watch, make sure that its auto light switch is
turned off before riding a bicycle or operating a motorcycle or any other
motor vehicle. Sudden and unintended operation of the auto light switch can
create a distraction, which can result in a traffic accident and serious
personal injury.
To turn the auto light switch on and off
In the Timekeeping Mode, hold down B for about three seconds to toggle the auto
light switch on (auto light switch on indicator displayed) and off (auto light switch on
indicator not displayed).
• The auto light switch on indicator is on the display in all modes while the auto light
switch is turned on.
Power Supply
This watch is equipped with a solar cell and a rechargeable battery that is charged by
the electrical power produced by the solar cell. The illustration shown below shows
how you should position the watch for charging.
Example: Orient the watch so its face is
pointing at a light source.
• The illustration shows how to position a
watch with a resin band.
• Note that charging efficiency drops when
any part of the solar cell is blocked by
clothing, etc.
• You should try to keep the watch outside of
your sleeve as much as possible. Charging
is reduced significantly if the face is
covered only partially.
Solar cell
E-40
E-41
Battery Power Indicator and Recover Indicator
lll
ll l
Level
1
ll l
ll l
ll l
lll
The battery power indicator on the display shows you the current status of the
rechargeable battery’s power.
ll l
Battery Power Indicator
ll l
2
Function Status
All functions enabled.
All functions enabled.
3
ll l
l l l ll
l
Battery power
indicator
ll
Illumination, and beeper
disabled.
ll l l l ll
(Charge Soon Alert)
4
l l lll
l
ll l
ll
l l l l l ll
Important!
• Storing the watch for long periods in an area where there is no light or wearing it in
such a way that it is blocked from exposure to light can cause rechargeable battery
power to run down. Be sure that the watch is exposed to bright light whenever
possible.
• This watch uses a rechargeable battery to store power produced by the solar cell, so
regular battery replacement is not required. However, after very long use, the
rechargeable battery may lose its ability to achieve a full charge. If you experience
problems getting the rechargeable battery to charge fully, contact your dealer or
CASIO distributor about having it replaced.
• Never try to remove or replace the watch’s rechargeable battery yourself. Use of the
wrong type of battery can damage the watch.
• All data stored in memory is deleted, and the current time and all other settings
return to their initial factory defaults whenever battery power drops to Level 5 (pages
E-43 and E-44) and when you have the battery replaced.
• Turn on the watch’s Power Saving function (page E-59) and keep it in an area
normally exposed to bright light when storing it for long periods. This helps to keep
the rechargeable battery from going dead.
5
Except for timekeeping and
the CHG (charge) indicator,
all functions and display
indicators disabled.
All functions disabled.
E-43
ll l
ll l
lll
ll l
ll l
ll l
ll l
ll
lll l lllll
ll
lll l l l lll
• The flashing LOW indicator at Level 3 tells you that battery power is very low, and
that exposure to bright light for charging is required as soon as possible.
• At Level 5, all functions are disabled and settings return to their initial factory
defaults. Once the battery reaches Level 2 after falling to Level 5, reconfigure the
current time, date, and other settings.
• The watch’s Home City code setting will change automatically to TYO (Tokyo)
whenever the battery drops to Level 5.
• Display indicators reappear as soon as the battery is charged from Level 5 to Level 2.
• Leaving the watch exposed to direct sunlight or some other very strong light source
can cause the battery power indicator to show a reading temporarily that is higher
than the actual battery level. The correct battery level should be indicated after a few
minutes.
lll
E-42
Recover indicator
• Performing illumination, or beeper operations during a
short period may cause the recover indicator to appear
on the display.
After some time, battery power will recover and the
recover indicator will disappear, indicating that the above
functions are enabled again.
• If the recover indicator appears frequently, it probably
means that remaining battery power is low. Leave the
watch in bright light to allow it to charge.
E-44
E-45
Charging Precautions
Certain charging conditions can cause the watch to become very hot. Avoid leaving
the watch in the areas described below whenever charging its rechargeable battery.
Also note that allowing the watch to become very hot can cause its liquid crystal
display to black out. The appearance of the LCD should become normal again when
the watch returns to a lower temperature.
Warning!
Leaving the watch in bright light to charge its rechargeable battery can cause it
to become quite hot. Take care when handling the watch to avoid burn injury.
The watch can become particularly hot when exposed to the following
conditions for long periods.
• On the dashboard of a car parked in direct sunlight
• Too close to an incandescent lamp
• Under direct sunlight
Charging Guide
The following table shows the amount of time the watch needs to be exposed to light
each day in order to generate enough power for normal daily operations.
Exposure Level (Brightness)
Outdoor Sunlight (50,000 lux)
Sunlight Through a Window (10,000 lux)
Daylight Through a Window on a Cloudy Day (5,000 lux)
Indoor Fluorescent Lighting (500 lux)
• For details about the battery operating time and daily operating conditions, see the
“Power Supply” section of the Specifications (page E-66).
• Stable operation is promoted by frequent exposure to light.
E-46
E-47
Recovery Times
The table below shows the amount exposure that is required to take the battery from
one level to the next.
Level 1
▲
20 hours
6 hours
8 hours
99 hours
27 hours
15 hours
--------
--------
172 hours
--------
--------
• The above exposure time values are all for reference only. Actual required exposure
times depend on lighting conditions.
E-48
The tide site names you can select depend on your current Home City setting.
• Select tide site names in the Timekeeping Mode.
• After configuring the settings for your Home City, press A once to display the tide
site name selection screen.
• Note that the tide sites you can select are those located in the same time zone as
your Home City. They are not necessarily located near your Home City.
To configure tide site settings
1. In the Timekeeping Mode, hold down A for about two
seconds until the city code starts to flash. This is the
ll lll
setting screen.
• The watch will exit the setting screen automatically if
you do not perform any operation for about two or
three minutes.
lll
2 hours
Selecting the Tide Site Name
lll
Outdoor Sunlight
(50,000 lux)
Sunlight Through a
Window (10,000 lux)
Daylight Through a
Window on a Cloudy
Day (5,000 lux)
Indoor Fluorescent
Lighting (500 lux)
Level 2
▲
▲
Approximate Exposure Time
Level 5
Level 4
Level 3
Tide Site Name
lllll
Exposure Level
(Brightness)
Approximate
Exposure Time
5 minutes
24 minutes
48 minutes
8 hours
E-49
ll lll
lll
lll
Operation Guide 3216 3223
2. Press A once to display the tide site name selection
screen.
• The current tide site name will be on the display and
SET will flash.
3. Use D (forward) and B (back) to scroll through the
tide site names until the one you want is displayed.
• If the tide site name is longer than four characters, the
name will scroll from right to left on the display.
• A tide site that does not have any data assigned to it
displays the name “USER”.
4. When all of the settings are the way you want, press A
to exit the setting screen.
• The tide graph in the Timekeeping Mode shows
information for the site you select here.
• The tide site candidates are those with the UTC
differential as the current Home City. If you cannot find
the site you want, you can select “USER”.
• Only “USER” sites may be available for some cities.
• Setting an accurate high tide time will allow the watch to produce accurate tide
readings. Especially when “USER” is selected as the site, make sure that you input
an accurate high tide time.
• Only a “USER” site can be selected while UTC is selected as the Home City.
lllll
E-50
E-51
(part you cannot see)
Reference
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
Moon Phase Indicator
ll l
ll l
lll
ll l
ll l
ll l
lll
Module 3216
ll l
Module
3223
Moon Age
Moon Phase
28.7-29.8
1.0-2.7 2.8-4.6 4.7-6.4 6.5-8.3 8.4-10.1 10.2-12.0 12.1-13.8
0.0-0.9
New
First
Moon
Quarter
(Waxing)
ll l
ll l
lll
ll l
ll l
ll l
lll
Moon Phase indicator
Module 3223
The Moon phase indicator of this watch indicates the
current phase of the Moon as shown below. It is based on
the view of the left side of the moon at meridian transit
from the northern hemisphere of the Earth. If the
appearance of the Moon phase indicator is reversed from
the actual Moon as viewed from your location, you can
use the procedure under “To reverse the displayed Moon
phase” (page E-22) to change the indicator.
Moon
Phase
Indicator
Moon phase (part you can see)
Module
3216
ll l
E-52
E-53
Moon phase (part you can see)
(part you cannot see)
Module
Moon
3216
Phase
Indicator
Module
3223
Moon Age
13.9-15.7 15.8-17.5 17.6-19.4 19.5-21.2 21.3-23.1 23.2-24.9 25.0-26.8 26.9-28.6
Moon Phase
Full
Moon
Tidal Movements
Tides are the periodic rise and fall of the water of oceans, seas, bays, and other
bodies of water caused mainly by the gravitational interactions between the Earth,
Moon and Sun. Tides rise and fall about every six hours. The Tide Graph of this watch
indicates tidal movement based on the Moon’s transit over a meridian and the lunitidal
interval. The Tide Graph calculates and graphically represents current tide conditions
in your currently selected site or USER site based on longitudes, lunar day length, and
lunitidal interval preset in watch memory, and on high tide times specified by you.
Last
Quarter
(Waning)
E-54
E-55
Intermediate Tide
Medium difference between high tide
and low tide.
Neap Tide
Small difference between high tide
and low tide. Occurs a few days
before and after the first quarter and
last quarter of a half moon.
lll
lll
lll
lll
Description
Large difference between high tide
and low tide. Occurs a few days
before and after a New Moon and Full
Moon.
Low tide
lll
Graph
lll
Tide Name
Spring Tide
• The Tide Graph flashes as shown below to indicate the tide range.
llll
The Tide Graph graphically represents the current tide condition using one of three
patterns that represent spring tide, intermediate tide, and neap tide, as shown below.
llll
Tide Graph
High tide
• The segments on either end of the Tide Graph flash during high tide.
Lunitidal Interval
Theoretically, high tide is at the moon’s transit over the meridian and low tide is about
six hours later. Actual high tide occurs somewhat later, due to factors such as
viscosity, friction, and underwater topography. Both the time differential between the
moon’s transit over the meridian until high tide and the time differential between the
moon’s transit over the meridian until low tide are known as the “lunitidal interval”.
Tides data is calculated using the lunitidal intervals preset for each site.
E-56
E-57
ll l
ll l
lll
ll l
ll l
ll l
lll
Button Operation Tone
Power Saving Function
The button operation tone sounds any time you press one
of the watch’s buttons. You can turn the button operation
tone on or off as desired.
• Even if you turn off the button operation tone, alarms,
the Hourly Time Signal, and other beepers all operate
normally.
ll l
Mute indicator
lll
lll
To turn the button operation tone on and off
1. In the Timekeeping Mode, hold down A until the city
code starts to flash, which indicates the setting screen.
lllll
2. Press C nine times until the current button operation
tone setting (
or
) appears.
3. Press D to toggle the setting between
(tone on)
and
(tone off).
4. Press A to exit the setting screen.
• The mute indicator is displayed in all modes when the
button operation tone is turned off.
lllll
E-58
When turned on, the Power Saving function enters a
sleep state automatically whenever the watch is left in an
area for a certain period where it is dark. The table below
shows how watch functions are affected by the Power
Saving function.
Power saving indicator
Elapsed Time
Display
in Dark
60 to 70 minutes Blank, with Power Saving
indicator flashing
6 or 7 days
Blank, with Power Saving
indicator not flashing
Operation
All functions enabled, except for the
display
Beeper tone, illumination, and display
are disabled.
• Wearing the watch inside the sleeve of clothing can cause it to enter the sleep state.
E-59
Operation Guide 3216 3223
• The watch will not enter the sleep state between 6:00 AM and 9:59 PM. If the watch
is already in the sleep state when 6:00 AM arrives, however, it will remain in the
sleep state.
To recover from the sleep state
Perform any one of the following operations.
• Move the watch to a well-lit area.
• Press any button.
• Angle the watch towards your face for reading (page E-39).
llll
• If you do not perform any operation for about two or three minutes while a setting
screen (with a flashing setting) is on the display, the watch will exit the setting screen
automatically.
Scrolling
The B and D are used in various modes and setting screens to scroll through data
on the display. In most cases, holding down these buttons during a scroll operation
scrolls at high speed.
Initial Screens
When you enter the World Time Mode or Alarm Mode, the data you were viewing
when you last exited the mode appears first.
llll
To turn Power Saving on and off
1. In the Timekeeping Mode, hold down A until the city
code starts to flash, which indicates the setting screen.
2. Press C 11 times until the Power Saving on/off screen
ll l l lll
appears.
3. Press D to toggle Power Saving on (
) and off
(
).
4. Press A to exit the setting screen.
On/Off status
• The Power Saving indicator is on the display in all
modes while Power Saving is turned on.
Auto Return
lll l lll
E-60
E-61
Timekeeping
• Resetting the seconds to 00 while the current count is in the range of 30 to 59
causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are
reset to 00 without changing the minutes.
• The year can be set in the range of 2000 to 2099.
• The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to change
it except after you have the watch’s battery replaced.
• The current time for all city codes in the Timekeeping Mode and World Time Mode is
calculated in accordance with the Coordinated Universal Time (UTC) for each city,
based on your Home City time setting.
World Time
• The seconds count of the World Time is synchronized with the seconds count of the
Timekeeping Mode.
Illumination Precautions
• The electro-luminescent panel that provides illumination loses power after very long
use.
• Illumination may be difficult to see when viewed under direct sunlight.
• The watch may emit an audible sound whenever the display is illuminated. This is
due to vibration of the EL panel used for illumination, and does not indicate
malfunction.
• Illumination turns off automatically whenever an alarm sounds.
• Frequent use of illumination runs down the battery.
Auto light switch precautions
• Avoid wearing the watch on the inside of your wrist. Doing so causes the auto light
switch to operate when it is not needed, which shortens battery life. If you want to
wear the watch on the inside of your wrist, turn off the auto light switch feature.
E-62
E-63
More than 15 degrees
too high
• Illumination may not turn on if the face of the watch is
more than 15 degrees above or below parallel. Make
sure that the back of your hand is parallel to the ground.
• Illumination turns off after a preset amount of time (1.5
or 3 seconds), even if you keep the watch pointed
towards your face.
• Static electricity or magnetic force can interfere with proper operation of the auto
light switch. If illumination does not turn on, try moving the watch back to the starting
position (parallel with the ground) and then tilt it back toward you again. If this does
not work, drop your arm all the way down so it hangs at your side, and then bring it
back up again.
• Under certain conditions, illumination may not turn on until about one second after
you turn the face of the watch towards you. This does not necessarily indicate
malfunction of the auto light switch.
• You may notice a very faint clicking sound coming from the watch when it is shaken
back and forth. This sound is caused by mechanical operation of the auto light
switch, and does not indicate a problem with the watch.
Specifications
Accuracy at normal temperature: ± 15 seconds a month
Timekeeping: Hour, minutes, seconds, p.m. (P), month, day, day of the week
Time format: 12-hour and 24-hour
Calendar system: Full Auto-calendar pre-programmed from the year 2000 to 2099
Other: Home City code (can be assigned one of 48 city codes); Standard Time /
Daylight Saving Time (summer time); Checking a Tide Site
Tide/Moon Data:
Moon phase indicator for specific date; Tide level for specific date and time
Other: High tide time adjustment; Moon phase reversal
World Time: 48 cities (31 time zones)
Other: Daylight Saving Time/Standard Time
Alarms: 5 daily alarms (four one-time alarms; one snooze alarm); Hourly Time Signal
Stopwatch:
Measuring unit: 1/100 second
Measuring capacity: 59' 59.99''
Measuring modes: Elapsed time, split time, two finishes
E-64
E-65
Countdown Timer:
Number of timers: 2 (one set)
Setting unit: 5 seconds
Range: 99 minutes 55 seconds each timer
Countdown unit: 1 second
Number of repeats: 1 to 10
5-second time up beeper
Illumination: EL (electro-luminescent panel); Full Auto Light Switch; Selectable
illumination duration
Other: Button operation tone on/off
Power Supply: Solar cell and one rechargeable battery
Approximate battery operating time: 11 months (from full charge to Level 4) under
the following conditions:
• Watch not exposed to light
• Internal timekeeping
• Display on 18 hours per day, sleep state 6 hours per day
• 1 illumination operation(1.5 second) per day
• 10 seconds of alarm operation per day
E-66
City Code Table
City
Code
PPG
HNL
ANC
YVR
LAX
YEA
DEN
MEX
CHI
NYC
SCL
YHZ
YYT
L
City
Pago Pago
Honolulu
Anchorage
Vancouver
Los Angeles
Edmonton
Denver
Mexico City
Chicago
New York
Santiago
Halifax
St. Johns
UTC Offset/
GMT Differential
–11
–10
–9
–8
–7
–6
–5
–4
–3.5
City
UTC Offset/
City
Code
GMT Differential
RIO Rio De Janeiro
–3
FEN Fernando de Noronha
–2
RAI
Praia
–1
UTC
LIS
Lisbon
0
LON
London
MAD
Madrid
PAR
Paris
ROM
Rome
+1
BER
Berlin
STO
Stockholm
ATH
Athens
CAI
Cairo
+2
JRS
Jerusalem
City
Code
MOW
JED
THR
DXB
KBL
KHI
DEL
KTM
DAC
RGN
BKK
City
Moscow
Jeddah
Tehran
Dubai
Kabul
Karachi
Delhi
Kathmandu
Dhaka
Yangon
Bangkok
UTC Offset/
GMT Differential
+3
+3.5
+4
+4.5
+5
+5.5
+5.75
+6
+6.5
+7
City
Code
SIN
HKG
BJS
TPE
SEL
TYO
ADL
GUM
SYD
NOU
WLG
City
Singapore
Hong Kong
Beijing
Taipei
Seoul
Tokyo
Adelaide
Guam
Sydney
Noumea
Wellington
UTC Offset/
GMT Differential
+8
+9
+9.5
+10
+11
+12
• Based on data as of July 2010.
• The rules governing global times (UTC offset and GMT differential) and summer
time are determined by each individual country.
L-1
Operation Guide 3216 3223
Tide Site Name List
City
Tide Site
Code
LIS NEWQUAY,GBR U.K.
LON ABERDEEN,GBR U.K.
KILLALA BAY,IRL IRELAND
PENICHE,POR PORTUGAL
CASCAIS,POR PORTUGAL
FUNCHAL,
MADEILA
MADEIRA
LAS PALMAS
GRAN CANARIA
CASABLANCA, MOROCCO
MAR
SAFI,MAR
MOROCCO
DAKAR,SEN
SENEGAL
USER
City
Code
MAD
PAR
ROM
BER
STO
Tide Site
BOUCAU,FRA
PORTUGALETE,
ESP
GIJON,ESP
MARSEILLE,FRA
PALERMO,ITA
USER
ATH CAPE TOWN,RSA
CAI DURBAN,RSA
JRS MOSSEL BAY,
RSA
USER
MOW TOLANARO,MAD
JED USER
FRANCE
SPAIN
SPAIN
FRANCE
ITALY
SOUTH AFRICA
SOUTH AFRICA
SOUTH AFRICA
MADAGASCAR
City
Tide Site
Code
THR USER
DXB LE PORT,
REUNION
REUNION
PORT LOUIS,
MAURITIUS
MRI
USER
KBL USER
KHI MALE,
MALDIVES
MALDIVES
USER
DEL GALLE,SRI
SRI LANKA
USER
KTM USER
City
Tide Site
Code
DAC USER
RGN USER
BKK PHUKET
THAILAND
TELUK DALAM, INDONESIA
NIAS
PULAU TELO,
INDONESIA
INA
SIBERUT,INA
INDONESIA
NORTH PAGAI, INDONESIA
INA
TANJUNG
INDONESIA
PRIOK
USER
L-3
L-2
City
Code
SIN
HKG
BJS
TPE
Tide Site
BENOA,BALI
AMPENAN,
LOMBOK
COWARAMUP
FREMANTLE
CATANDUANES,
PHI
SIARGAO,PHI
USER
SEL ENOSHIMA
TYO SHIMODA
SHIKINEJIMA
OMAEZAKI
City
Code
INDONESIA
INDONESIA
Tide Site
IRAGO
WAKAYAMA
KANNOURA
HOSOSHIMA
NISHINOOMOTE
NAZE
NAHA
SENDAI
SOMA
KASHIMA
KAZUSAKATSUURA
USER
AUSTRALIA
AUSTRALIA
PHILIPPINES
PHILIPPINES
JAPAN
JAPAN
JAPAN
JAPAN
JAPAN
JAPAN
JAPAN
JAPAN
JAPAN
JAPAN
JAPAN
JAPAN
JAPAN
JAPAN
JAPAN
City
Tide Site
Code
ADL VICTOR
AUSTRALIA
HARBOR
USER
GUM NOOSA HEADS AUSTRALIA
SYD BUNDALL
AUSTRALIA
POINT DANGER AUSTRALIA
TWEED RIVER AUSTRALIA
BYRON BAY
AUSTRALIA
BALLINA
AUSTRALIA
SYDNEY
AUSTRALIA
ULLADULLA
AUSTRALIA
LORNE
AUSTRALIA
City
Code
Tide Site
HOBART
GUAM
USER
NOU NOUMEA
USER
WLG SUVA,FIJ
RAGLAN,NZL
USER
PPG PAGO PAGO
AUSTRALIA
GUAM
NEW CALEDONIA
FIJI ISLANDS
NEW ZEALAND
AMERICAN
SAMOA
USER
L-5
L-4
City
Tide Site
Code
HNL HONOLULU
U.S.A.
WAIALUA BAY,
U.S.A.
OAHU
KAHULUI,MAUI U.S.A.
HILO BAY,
U.S.A.
HAWAII
NAWILIWILI,
U.S.A.
KAUAI
PAPEETE,TAHITI TAHITI
USER
ANC USER
YVR SAN FRANCISCO U.S.A.
U.S.A.
LAX MONTEREY
PORT SAN LUIS U.S.A.
L-6
City
Code
Tide Site
SANTA BARBARA
PORT HUENEME
SANTA MONICA
L.A.HARBOR
NEWPORT BAY
LA JOLLA
ENSENADA,MEX
USER
YEA USER
DEN USER
MEX MANZANILLO,MEX
CHI PUNTARENAS,CRC
USER
U.S.A.
U.S.A.
U.S.A.
U.S.A.
U.S.A.
U.S.A.
MEXICO
MEXICO
COSTA RICA
City
Tide Site
Code
NYC ATLANTIC CITY U.S.A.
VIRGINIA BEACH U.S.A.
PORT CANAVERAL U.S.A.
MIAMI HARBOR U.S.A.
KINGSTON,JAM JAMAICA
BALBOA,PAN
PANAMA
PUERTO
EQUADOR
LOPEZ,ECU
PUERTO
PERU
CHICAMA
USER
SCL SANTO DOMINGO DOMINICAN R.
YHZ SAN JUAN,PUR PUERTO RICO
City
Code
Tide Site
BRIDGETOWN
VALPARAISO,CHI
USER
YYT USER
RIO RIO DE
JANEIRO
SANTOS
USER
FEN F.D.NORONHA
USER
RAI PONTA
DELGADA
USER
BARBADOS
CHILE
BRAZIL
BRAZIL
BRAZIL
AZORES
• For information about city names, see the City Code Table (page L).
L-7
Download PDF

advertising