Casio | Watch 5236 | User's Manual | Casio Watch 5236 User's Manual

MA1104-EA
Operation Guide 5168/5236
••Your watch may differ somewhat from the one shown in the illustration.
Hour hand
■■ For a watch with an elapsed time bezel
mark with the
Rotate the elapsed time bezel to align the
minute hand.
After certain amount of time elapsed, read the graduation on
the elapsed time bezel which the minute hand points to.
The elapsed time is indicated.
Hour hand
Minute hand
Minute hand
Elapsed time bezel
First click
(Setting day)
First click
(Setting day)
Second hand
Day
Crown
(Normal position)
Second click
(Setting time)
Second click
(Setting time)
Crown
(Normal position)
Second hand
••Some water resistant models are equipped with a screw
lock crown.
••With such models, you must unscrew the crown in the
direction noted in the illustration to loosen it before you can
pull it out. Do not pull too forcibly on such crowns.
••Also note that such watches are not water resistant while
their crowns are loosened. Be sure to screw the crowns
back in as far as they will go after making any setting.
Day
24-hour hand
24-hour hand
[5168]
[5236]
To set the time
1. Pull the crown out to the second click.
••At this time, the second hand will move to 0 (reset position) and stop there.
2. Set the hands by rotating the crown. Rotate the crown to move the hands
clockwise. Move the minute hand four or five minutes past the time you want to
set, and then back it up to the proper setting.
••Carefully set the time, making sure to distinguish between AM and PM.
3. Push the crown back in to the normal position to restart timekeeping.
Specifications
Accuracy at normal temperature: ± 20 seconds a month
Display: 3 analog hands (timekeeping hour and minutes, stopwatch seconds),
4 dials (timekeeping 24-hour, timekeeping seconds/stopwatch 1/20 second,
stopwatch hours, stopwatch minutes), day
Stopwatch function: Measuring capacity: 11:59'59.95"
Measuring unit: 1/20 second
Measuring mode: Elapsed time
Battery: One silver oxide battery (Type: SR927W)
Approximately 2 years on type SR927W
To set the day
1. Pull the crown out to the first click.
2. Set the day by rotating the crown.
3. Push the crown back in to the normal position.
••Avoid changing the date setting while the current time is between 9:00 p.m. and
1:00 a.m.
Using the Stopwatch
Stopwatch minute hand
(2 minutes)
Stopwatch hour hand
(10 hours)
Stopwatch second hand
(37 seconds)
[5168]
Stopwatch minute hand
(2 minutes)
Stopwatch hour hand
(10 hours)
Stopwatch second hand
(37 seconds)
Stopwatch 1/20 second hand
(.8 second)
••This hand moves right and left
to indicate the 1/20 second
count during the first
60 seconds.
[5236]
Stopwatch 1/20 second hand
(.8 second)
••This hand moves right and left
to indicate the 1/20 second
count during the first
60 seconds.
The stopwatch lets you measure elapsed time up to 11 hours, 59 minutes,
59.95 seconds.
To measure elapsed time
1. Press B to enter the Stopwatch Mode.
••The stopwatch 1/20 second hand will move to the 0 position.
2. Press A to start the stopwatch.
3. Press A to stop the stopwatch.
••You can resume the measurement operation by pressing A again.
4. Check the elapsed time.
••The example above shows an elapsed time of 10 hours, 2 minutes,
37.80 seconds.
••Press B to reset the stopwatch.
To return the function of the stopwatch 1/20 second hand to the timekeeping
second hand (indicating the current seconds count), press B again. This will
enter the Timekeeping Mode.
Notes:
••Do not try to perform stopwatch operations while the crown is pulled out either
to the first or second click. If you try to press a button, you might accidentally
cause the crown to rotate and change the current time or day setting.
••If the starting positions of the stopwatch second hand and 1/20 second hand
become misaligned, use the following procedures to adjust the position of the
stopwatch second hand so it points to 12 o’clock and the 1/20 second hand so
it points to .0 when the stopwatch is reset.
To adjust the positions of the stopwatch hands
1. Press B to reset the stopwatch, and check the alignment of the stopwatch
second hand (12 o’clock) and 1/20 second hand (12 o’clock).
2. Pull out the crown to the second click.
3. Press A to move the stopwatch second hand.
4. If the stopwatch 1/20 second hand is aligned correctly, proceed to step 5. If
the stopwatch 1/20 second hand is also misaligned, press B to move the
stopwatch 1/20 second hand.
5. After making the adjustments you want, push the crown back in to its normal
position.
••Note that pulling the crown out also stops the timekeeping second hand. After
performing the above procedure, you should also adjust the timekeeping setting.
1
Download PDF

advertising