Casio MO1211-EA User's Manual

Casio MO1211-EA User's Manual
© 2012 CASIO COMPUTER CO., LTD.
MO1211-EA
Operation Guide 5299
Getting Acquainted
Congratulations upon your selection of this CASIO watch. To get the most out of your
purchase, be sure to read this manual carefully.
Warning!
• The measurement functions built into this watch are not intended for taking
measurements that require professional or industrial precision. Values produced
by this watch should be considered as reasonable representations only.
• The Moon phase indicator and tide graph data that appear on the display of this
watch are not intended for navigation purposes. Always use proper instruments
and resources to obtain data for navigation purposes.
• This watch is not an instrument for calculating low tide and high tide times. The
tide graph of this watch is intended to provide a reasonable approximation of
tidal movements only.
• Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any
damage or loss suffered by you or any third party arising through the use of this
product or its malfunction.
E-1
• Each section of this manual provides you with the information you need to perform
operations in each mode. Further details and technical information can be found in
the “Reference” section.
About This Manual
Type A
Type B
• Depending on the model of your watch, display text appears either as dark figures
on a light background (Type A) or light figures on a dark background (Type B). All
sample displays in this manual are shown using dark figures on a light background.
• Button operations are indicated using the letters shown in the illustration.
E-2
E-3
Procedure Lookup
Contents
General Guide ......................................................................................................... E-8
Timekeeping .......................................................................................................... E-10
Thermometer ......................................................................................................... E-16
Specifying Temperature Unit ............................................................................... E-21
Temperature Reading Precautions ..................................................................... E-22
Tide and Moon Data .............................................................................................. E-23
Stopwatch .............................................................................................................. E-34
Countdown Timer .................................................................................................. E-37
World Time ............................................................................................................. E-40
Alarms .................................................................................................................... E-44
Illumination ............................................................................................................ E-49
Hand Home Position Correction .......................................................................... E-53
Reference .............................................................................................................. E-55
Specifications ....................................................................................................... E-61
The following is a handy reference list of all the operational procedures contained in
this manual.
To set the time and date ....................................................................................... E-11
To change the Daylight Saving Time (summer time) setting ............................ E-14
To take a temperature reading ............................................................................. E-16
To calibrate the temperature sensor ................................................................... E-19
To specify the temperature unit ........................................................................... E-21
To view current tide and Moon data .................................................................... E-24
To adjust the high tide time ................................................................................. E-31
To reverse the displayed Moon phase ................................................................ E-33
To use the countdown timer ................................................................................ E-38
E-4
E-5
To configure countdown start time settings ...................................................... E-39
To turn the auto light switch on and off .............................................................. E-52
To view the current time in another time zone ................................................... E-41
To adjust home positions ..................................................................................... E-53
To toggle a city code time between Standard Time
and Daylight Saving Time ............................................................................... E-42
To turn the button operation tone on and off ..................................................... E-56
To swap your Home City and World Time City ................................................... E-43
To set an alarm time ............................................................................................. E-45
To test the alarm ................................................................................................... E-46
To turn an alarm on and off .................................................................................. E-47
To turn the Hourly Time Signal on and off .......................................................... E-48
To illuminate the display manually ...................................................................... E-49
To specify the illumination duration ................................................................... E-50
E-6
E-7
Stopwatch Mode (page E-34)
General Guide
Countdown Timer Mode (page E-37)
▲
C
▲
• Press C to change from mode to mode.
• To return to the Timekeeping Mode from any other mode, hold down C for about
three seconds.
• In any mode (except a setting mode), press B to illuminate the display.
Tide/Moon Data Mode
(page E-23)
Timekeeping Mode
D
C
Alarm Mode (page E-44)
World Time Mode (page E-40)
C
C
▲
▲
▲
▲
D
E-8
C
▲
▲
Thermometer Mode
(page E-16)
C
E-9
Operation Guide 5299
To set the time and date
Timekeeping
City code
You can adjust the Home city date and time in the Timekeeping Mode.
• Pressing A in the Timekeeping Mode will toggle the lower display between the
screens shown below.
Home City Date
Home City Time
Day of the week
Day of the week
Date
▲
▲
A
Seconds
PM indicator
Seconds
Hour : Minutes
E-10
E-11
3. Press C to change the flashing screen content in the sequence shown below to
select the other settings.
C 12/24-Hour C
C
C
City C
DST
Seconds
Hour
Minutes
Code
Format
C
Illumination
Duration
C
Button
Operation Tone
C
Day
C
Month
C
Screen:
To do this:
Toggle between 12-hour (
24-hour (
) timekeeping
Reset the seconds to
C
To do this:
Change the city code
Toggle the DST setting between
Daylight Saving Time ( ) and
Standard Time (
).
) and
Change the hour and minutes
Year
4. When the timekeeping setting you want to change is flashing, use D or B to
change it as described below.
Screen:
1. In the Timekeeping Mode, hold down A for about two
seconds until SET appears on the lower display. This is
the setting mode.
• Note that keeping A depressed too long (for about
five seconds) will cause a different type of setting
mode to be entered (page E-53).
2. Use D and B to select the city code you want.
• Make sure you select your Home City code before
changing any other setting.
• For full information on city codes, see the “City Code
Table” at the back of this manual.
Do this:
Press D.
Press D.
Use D (+) and B (–).
Change the year, month, or day
Do this:
Use D (east) and B
(west).
Press D.
Toggle the button operation tone
between
(on) and
(off)
Toggle the display illumination
duration between 1.5 seconds ( )
and three seconds ( )
Press D.
Press D.
E-12
E-13
5. Press A to exit the setting mode.
• The day of the week is displayed automatically in accordance with the date (year,
month, and day) settings.
3. Use D to toggle the DST setting on and off.
Daylight Saving Time (DST)
• The default DST setting is OFF (
).
4. When the setting you want is selected, press A to exit the setting mode.
• The DST indicator appears to indicate that Daylight Saving Time is turned on.
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down A for about two
seconds until SET appears on the display.
• Note that keeping A depressed too long (for about
five seconds) will cause a different type of setting
mode to be entered (page E-53).
2. Press C. This will display the DST setting screen.
E-14
)
D
DST on (
)
12-hour and 24-hour timekeeping
• With the 12-hour format, the PM indicator (P) appears on the lower display for times
in the range of noon to 11:59 p.m. and no indicator appears for times in the range of
midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
the PM indicator (P).
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all other modes.
DST indicator
Thermometer
This watch uses a temperature sensor to take temperature readings.
To take a temperature reading
1. In the Timekeeping Mode, press D to enter the
Thermometer Mode and start a temperature reading
operation.
• The first temperature reading will take about three
seconds. After that, readings are taken at two-second
intervals for the first two minutes, and then at twominute intervals after that.
• The displayed temperature will be updated with each
reading.
Temperature
E-16
Temperature Sensor Calibration
The watch’s temperature sensor is calibrated at the factory and normally requires no
further adjustment. If you notice serious errors in the temperature readings produced
by the watch, you can calibrate the sensor to correct the errors.
Important!
• Incorrectly calibrating the temperature sensor can result in incorrect readings.
Carefully read the following before doing anything.
– Compare the readings produced by the watch with those of another reliable and
accurate thermometer.
– If adjustment is required, remove the watch from your wrist and wait for 20 or 30
minutes to give the temperature of the watch time to stabilize.
E-18
DST off (
E-15
2. To stop the temperature reading operation, press D to return to the Timekeeping
Mode.
• The watch will stop taking temperature readings and return to the Timekeeping
Mode automatically if you do not perform any operation for about one or two hours.
Temperature
• Temperature is displayed in units of 0.1°C (or 0.2°F).
• The displayed temperature value changes to - - - °C (or °F) if a measured
temperature falls outside the range of –10.0°C to 60.0°C (14.0°F to 140.0°F). The
temperature value will reappear as soon as the measured temperature is within the
allowable range.
Display Units
You can select either Celsius (°C) or Fahrenheit (°F) for the displayed temperature
value. See “To specify the temperature unit” (page E-21) for more information.
E-17
To calibrate the temperature sensor
1. Enter the Thermometer Mode, which will start a
temperature reading operation and display the results
(page E-16).
2. Hold down A for about two seconds.
• Holding down A will initially cause Hold to appear on
the screen. Keep A depressed until Hold disappears.
• This will cause the temperature reading operation to
re-start, and display the sensor calibration screen
shown in the illustration nearby.
3. Use D (+) and B (–) to change the displayed calibration by 0.1°C (0.2°F) steps.
• To return the currently flashing value to its initial factory default setting, press D
and B at the same time. OFF will appear in place of the flashing temperature
value for about two seconds, followed by the initial default value.
4. Press A to return to the Thermometer Mode screen and take temperature
readings.
E-19
Operation Guide 5299
Thermometer Precautions
• Temperature measurements are affected by your body temperature (while you are
wearing the watch), direct sunlight, and moisture. To achieve a more accurate
temperature measurement, remove the watch from your wrist, place it in a well
ventilated location out of direct sunlight, and wipe all moisture from the case. It takes
approximately 20 to 30 minutes for the case of the watch to reach the actual
surrounding temperature.
Specifying Temperature Unit
Use the procedure below to specify the temperature unit to be used in the
Thermometer Mode.
Important!
When TOKYO is selected as the Home City, the
temperature unit is set automatically to Celsius (°C).
These settings cannot be changed.
To specify the temperature unit
1. While the temperature sensor calibration screen is
displayed (page E-19), press C to toggle between the
temperature units as shown in the nearby illustration.
2. Press D to toggle the temperature unit between °C
(Celsius) and °F (Fahrenheit).
3. After the setting is the way you want, press A to exit
the setting screen.
E-20
E-21
Temperature Reading Precautions
Tide and Moon Data
When taking temperature readings, it is best to remove the watch from your wrist in
order to eliminate the effects of body heat. Remove the watch from your wrist and
allow it to hang freely from your bag or in another location where it is not exposed to
direct sunlight.
You can use the watch to check the current tide, Moon phase, and Moon age in your
area.
• Basic calculations to determine this data is performed based on your current Home
City setting (page E-11). You can also check the tide and Moon data in another
location by temporarily selecting the applicable city as your Home City.
• Note that the tide and Moon data calculated by this watch are approximate and are
intended as general information only. Never try to use it for marine navigation or any
other purposes requiring accurate measurements.
E-22
E-23
To view current tide and Moon data
The current tide*1 and Moon phase*2 are displayed in the
Moon phase indicator
Timekeeping Mode (page E-8).
(pages E-28, E-32)
*1 Shows the tide for the displayed date and time.
*2 Shows the Moon phase for the displayed date.
The Moon phase shows the phase at noon of the
displayed date. The current time does not affect the
displayed Moon phase.
High tide
▲
▲
▲
▲
Tide Graph
The tide is indicated as
shown on the next page.
Low tide
E-24
E-25
Viewing Tide and Moon Data for a Particular Date and Time
In the Tide/Moon Data Mode (page E-8), you can view the tide and moon phase for a
particular date and time. You can also view the applicable moon age in this mode
(which is not shown in the Timekeeping Mode).
Tide Data Screen
Month - Day
Tide Graph
(page E-25)
E-26
1. Entering the Tide/Moon Data Mode displays the Tide
Data Screen and indicates the tide for the current date
at 6:00 a.m.
• You can check the tide for another date by performing
steps 3 through 5 below before performing step 2. You
cannot change the date while the Tide Data Screen is
displayed.
2. Use D to change the time setting.
• Each press of D advances the time by one hour and
calculates tide data for that time. Holding down D for
about two seconds scrolls at high speed.
Moon Data Screen
Month - Day
Moon age
(page E-28)
Moon phase indicator
(page E-28)
Time
Moon phase (part you can see)
Moon phase (part you can see)
Type A
Moon
(page
Phase
Indicator E-2)
Type A
Moon
(page
Phase
Indicator E-2)
Type B
(page
E-2)
Type B
(page
E-2)
Moon Phase
E-28
Note
• The margin of error for the Moon age is ±1 day.
• If the data is not displayed correctly, check the
Timekeeping Mode date, time, and Home City settings.
If the data is still not displayed correctly, see “Adjusting
the High Tide Time” (page E-30) and “Reversing the
Displayed Moon Phase” (page E-32).
E-27
(part you cannot see)
Moon Age
3. Press A to display the Moon Data Screen.
• This will display the Moon phase and Moon age for
the current date.
4. Use D to change the date setting.
• Each press of D advances the date by one day and
calculates tide data for that date. Holding down D for
about two seconds scrolls at high speed.
• You can select any date between January 1, 2000 and
December 31, 2099.
5. Press A again to return to the Tide Data Screen.
28.7-29.8
1.0-2.7 2.8-4.6 4.7-6.4 6.5-8.3 8.4-10.1 10.2-12.0 12.1-13.8
0.0-0.9
New
First
Moon
Quarter
(Waxing)
(part you cannot see)
Moon Age
13.9-15.7 15.8-17.5 17.6-19.4 19.5-21.2 21.3-23.1 23.2-24.9 25.0-26.8 26.9-28.6
Moon Phase
Full
Moon
Last
Quarter
(Waning)
E-29
Operation Guide 5299
Adjusting the High Tide Time
Use the following procedure to adjust the high tide time within a particular date. You
can find out high tide information for your area from a tide table, the Internet, or your
local newspaper.
To adjust the high tide time
1. In the Tide/Moon Data Mode, press A to display the
Moon Data Screen (page E-27).
2. Press D to scroll the date until one whose high tide
time you want to change is displayed.
3. Hold down A until the hour digits start to flash.
4. Press D (+) and B (–) to change the hour setting.
5. When the hour is the setting you want, press C.
• This will cause the minute digits to flash.
6. Press D (+) and B (–) to change the minute setting.
Hour
7. When the minute setting is the way you want, press A
to exit the adjustment screen and return to the Tide/
Moon Data Mode screen.
• Pressing D and B at the same time while the time
adjustment screen is displayed (steps 4 through 7
above) will return the high tide time to its initial factory
default setting.
• The high tide time setting is affected by the DST
(summer time) setting of the Timekeeping Mode.
Minute
E-30
E-31
• On some days, there are two high tides. With this watch, you can adjust the first high
tide time only. The second high tide time for that day is adjusted automatically based
on the first high tide time.
Reversing the Displayed Moon Phase
The left-right (east-west) appearance of the Moon depends on whether the Moon is
north of you (northerly view) or south of you (southerly view) as you view it.
You can use the procedure below to reverse the displayed Moon phase so it matches
the actual appearance of the Moon where you are located.
• To determine the viewing direction of the Moon, use a compass to take a direction
reading of the Moon at its meridian passage.
To reverse the displayed Moon phase
1. In the Tide/Moon Data Mode, hold down A until the
hour digits start to flash.
2. Press C twice.
• This will cause the Moon phase indicator to flash. This
is the indicator switching screen.
3. Press D to toggle the Moon phase indicator between
the southerly view (indicated by
) and northerly
).
view (indicated by
• Northerly view: Moon is north of you.
• Southerly view: Moon is south of you.
4. When the Moon phase indicator setting is the way you
want, press A to exit the switching screen and return
to the Tide/Moon Data Mode screen.
E-32
E-33
Elapsed Time Measurement
Stopwatch
You can use the stopwatch to measure elapsed time and
split times.
• The digital display range of the stopwatch is 999 hours,
59 minutes, 59.99 seconds. The stopwatch continues to
run until you stop it. If it reaches the above limit, it will
restart the time measurement from zero.
• The stopwatch operation continues even if you exit the
Stopwatch Mode.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C (page
E-9).
In the Stopwatch Mode, press D to start and stop elapsed time measurement.
• Pressing A while elapsed time measurement is in progress will display the current
split time.
Start
Split
Split
cancel
Stop
Display
time reset
D
A
A
D
A
(Measured time
displayed.)
(Stopped)
(Split time
displayed.)
(Measured time
displayed.)
(Measurement)
(Stopped)
E-34
E-35
Measured time or split time
Countdown Timer
You can set the countdown timer start time within a range
of one minute to 24 hours. An alarm sounds when the
countdown reaches zero.
• All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C (page E-9).
Hours
• Alternates with SPL during
split time display.
Minutes, seconds,
1/100 seconds
• Pressing D without resetting the displayed time will restart elapsed time
measurement from where it was last stopped (cumulative elapsed time
measurement).
• An ongoing elapsed time measurement operation continues even if you exit the
Stopwatch Mode.
Seconds
Start time
(Hours : Minutes)
E-36
To use the countdown timer
Press D while in the Countdown Timer Mode to start the countdown timer.
• When the end of the countdown is reached, the alarm will sound for 10 seconds or
until you stop it by pressing any button.
• The countdown time is reset to its starting value automatically after the alarm stops.
• Press D while a countdown operation is in progress to pause it.
Press D again to resume the countdown.
• To stop a countdown timer operation completely, first pause it (by pressing D), and
then press A. This returns the countdown time to its starting value.
E-37
To configure countdown start time settings
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A for about two
seconds until the hour setting of the countdown start
time starts to flash. This is the setting mode.
• Holding down A will initially cause Hold to appear on
the screen. Keep A depressed until Hold disappears.
• If the countdown start time is not displayed, use the
procedure under “To use the countdown timer” (page
E-38) to display it.
2. Press C to move the flashing in the sequence shown
Start time
below,
and select the setting you want to change.
(Hours : Minutes)
Start Time
(Hours)
C Start Time
(Minutes)
C
3. Press A to exit the setting mode.
E-38
E-39
Operation Guide 5299
World Time
Currently selected
World Time City
To view the current time in another time zone
In the World Time Mode, use D to scroll through available city codes (time zones).
Holding down the button scrolls at high speed.
• The lower display shows the current time in the World Time City.
• To select the UTC time zone (Differential 0), press B and D at the same time.
• When the city code (time zone) you want is selected, you can press A to display
the date. After about one second, the watch will resume regular timekeeping for the
currently selected city.
A
▲
World Time
World Time digitally displays the current time in one of
48 cities (29 time zones) around the world. A simple
operation swaps your Home City with the currently
selected World Time City.
• The times kept in the World Time Mode are
synchronized with the time being kept in the
Timekeeping Mode. If you feel that there is an error in
any World Time Mode time, check to make sure you
have the correct city selected as your Home City. Also
check to make sure that the current time as shown in
the Timekeeping Mode is correct.
• Times in the World Time Mode are based on UTC
offsets. See the “City Code Table” at the back of this
manual for information about the UTC offsets that are
supported.
One second
Seconds
• All of the operations in this section are performed in the World Time Mode, which
you enter by pressing C (page E-9).
Hour : Minutes
Date
E-40
E-41
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, press D to display the city
code (time zone) whose Standard Time/Daylight Saving
Time setting you want to change.
2. Hold down A for about two seconds to toggle between
Daylight Saving Time ( DST indicator displayed) and
Standard Time ( DST indicator not displayed).
• Holding down A will initially cause Hold to appear on
the screen. Keep A depressed until Hold disappears.
• The DST indicator is shown in the lower display while
Daylight Saving Time is turned on.
• You can turn on DST individually for each city code,
DST indicator
except UTC.
• Turning on DST for the city code that is currently
selected as your Home City will turn on DST for normal
timekeeping.
Swapping your Home City and World Time City
You can use the procedure below to swap your Home City and World Time City. This
changes your Home City to your World Time City, and your World Time City to your
Home City. This capability can come in handy when you frequently travel between two
cities in different time zones.
To swap your Home City and World Time City
1. In the World Time Mode, use D to select the World Time City you want.
2. Press A and B at the same time until the watch beeps.
• This will make the World Time City you selected in step 1 your Home City, and cause
the hour and minute hands to move to the current time in that city. At the same time,
it will change the Home City you had selected prior to step 2 your World Time City,
and cause the content of lower display to change accordingly.
• After swapping the Home City and World Time City, the watch stays in the World
Time Mode with the city that was selected as the Home City prior to step 2 now
displayed as the World Time City.
E-42
E-43
To set an alarm time
Alarms
Alarm time
(Hour : Minutes)
When an alarm is turned on, the alarm tone will sound
when its alarm time is reached. One of the alarms is a
snooze alarm, while the other four are daily alarms.
You also can turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour.
• The snooze alarm screen is indicated by
, while the
other alarm screens are numbered
through
.
The Hourly Time Signal screen is indicated by
.
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C (page
E-9).
E-44
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
D
D
D
D
D
OFF
D
• To set an alarm time, display the applicable alarm
screen (
through
, or
).
•
is the hourly time signal setting (page E-48).
• The snooze alarm operation repeats every five
minutes.
2. After you select an alarm, hold down A for about two seconds until the hour setting
of the alarm time starts to flash. This is the setting mode.
• Holding down A will initially cause Hold to appear on the screen. Keep A
depressed until Hold disappears.
• This operation turns on the alarm automatically.
3. Press C to move the flashing between the hour and minute settings.
E-45
4. While a setting is flashing, use D (+) and B (–) to change it.
5. Press A to exit the setting mode.
Alarm Operation
The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, or until you turn the alarm off (page E-47).
• Alarm and Hourly Time Signal operations are performed in accordance with the
current time in your Home City, as kept in the Timekeeping Mode.
• To stop the alarm tone after it starts to sound, press any button.
• Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen (page E-11)
Displaying the
setting screen (page E-45)
To turn an alarm on and off
1. In the Alarm Mode, use D to select an alarm.
Snooze alarm indicator
2. Press A to toggle it on and off.
• Turning on an alarm (
,
,
,
or
)
displays the alarm on indicator on its Alarm Mode
screen.
• In all modes, the alarm on indicator is shown for any
alarm that currently is turned on.
• The alarm on indicator flashes while the alarm is
sounding.
• The snooze alarm indicator flashes while the snooze
alarm is sounding and during the 5-minute intervals
ON
between alarms.
Alarm on indicator
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
E-46
E-47
To turn the Hourly Time Signal on and off
1. In the Alarm Mode, use D to select the Hourly Time
Signal (
) (page E-45).
2. Press A to toggle it on and off.
• The Hourly Time Signal on indicator is shown on the
display in all modes while this function is turned on.
Illumination
An LED (light-emitting diode) illuminates the face of the
watch for easy reading in the dark. The watch’s auto light
switch turns on illumination automatically when you angle
the watch towards your face.
• The auto light switch must be turned on (indicated by
the auto light switch indicator) for it to operate.
• See “Illumination Precautions” (page E-59) for other
important information about using illumination.
ON
Hourly Time Signal
on indicator
E-48
Auto light switch
indicator
To illuminate the display manually
In any mode, press B to turn on illumination.
• The above operation turns on illumination regardless of
the current auto light switch setting.
• You can use the procedure below to select either 1.5
seconds or 3 seconds as the illumination duration. When
you press B, the illumination will remain on for about
1.5 seconds or 3 seconds, depending on the current
illumination duration setting.
E-49
Operation Guide 5299
To specify the illumination duration
1. In the Timekeeping Mode, hold down A for about two
LIGHT
seconds until SET appears on the display.
• Note that keeping A depressed too long (for about
five seconds) will cause a different type of setting
mode to be entered (page E-53).
2. Press C ten times to display the current illumination
duration or .
3. Press D to toggle the setting between (1.5 seconds)
and (three seconds).
4. Press A to exit the setting screen.
About the Auto Light Switch
Turning on the auto light switch causes illumination to turn on, whenever you position
your wrist as described below in any mode.
Moving the watch to a position that is parallel to the ground and then tilting it towards
you more than 40 degrees causes illumination to turn on.
• Wear the watch on the outside of your wrist.
Parallel to
ground
More than
40°
E-50
E-51
Warning!
• Always make sure you are in a safe place whenever you are reading the
display of the watch using the auto light switch. Be especially careful when
running or engaged in any other activity that can result in accident or injury.
Also take care that sudden illumination by the auto light switch does not
startle or distract others around you.
• When you are wearing the watch, make sure that its auto light switch is turned
off before riding a bicycle or operating a motorcycle or any other motor
vehicle. Sudden and unintended operation of the auto light switch can create a
distraction, which can result in a traffic accident and serious personal injury.
To turn the auto light switch on and off
In the Timekeeping Mode, hold down B for about three seconds to toggle the auto
light switch on (auto light switch indicator displayed) and off (auto light switch indicator
not displayed).
• The auto light switch indicator remains in all modes while the auto light switch is
turned on.
• In order to protect against running down the battery, the auto light switch will turn off
automatically approximately six hours after you turn it on. Repeat the above
procedure to turn the auto light switch back on if you want.
Hand Home Position Correction
The Tide Graph, and the hour and minute hands of the watch can be thrown off by
exposure to strong magnetism or impact. If this happens, you can correct their home
positions as required.
To adjust home positions
1. In the Timekeeping Mode, hold down A for about five
seconds until H-SET (
) appears in the upper
display and Sub (
) appears in the lower display.
2. Check the position of the Tide Graph.
• The Tide Graph is in the correct home position if it is
indicating HIGH (12 o’clock position). If it is not
correct, use the D (+) and B (–) buttons to adjust it.
• After confirming that the Tide Graph is in its correct
home position, press C.
Correct Tide Graph
position
E-52
Correct hour and minute
hand positions
E-53
3. Check the positions of the hour and minute hands.
• The hands are in the correct home positions if they
are pointed at 12 o’clock. If they aren’t, use D
(clockwise) and B (counterclockwise) to adjust their
positions.
4. When everything is the way you want, press A to
return to regular timekeeping.
• This will cause the hour and minute hands to move to
the current Timekeeping Mode time, and the Tide Graph
to move to the HIGH position.
• Pressing C here will return to the setting at the
beginning of step 2.
Reference
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
Button Operation Tone
The button operation tone sounds any time you press one
of the watch’s buttons. You can turn the button operation
tone on or off as desired.
• Even if you turn off the button operation tone, alarms,
the Hourly Time Signal, and other beepers all operate
normally.
Mute indicator
E-54
To turn the button operation tone on and off
1. In the Timekeeping Mode, hold down A for about two seconds until SET appears
on the display.
• Note that keeping A depressed too long (for about five seconds) will cause a
different type of setting mode to be entered (page E-53).
2. Press C nine times until the current button operation tone setting (
or MUTE)
appears.
3. Press D to toggle the setting between
(tone on) and MUTE (tone off).
4. Press A to exit the setting screen.
• The mute indicator is displayed in all modes when the button operation tone is
turned off.
Auto Return Features
E-55
Mode Name
Tide/Moon Data, Alarm
Thermometer
Approximate Elapsed Time
2 to 3 minutes
1 to 2 hours
High-Speed Movement
• The D and B buttons are used to change setting in various setting modes. In most
cases, holding down these buttons will start high-speed movement.
Initial Screens
When you enter the Stopwatch Mode, World Time Mode or Alarm Mode, the data you
were viewing when you last exited the mode will appear first.
• If you leave the watch with a flashing setting on the display for two or three minutes
without performing any operation, the watch will exit the setting mode automatically.
• The watch will automatically return to the Timekeeping Mode if you do not perform
any button operation for a particular amount of time in each mode.
E-56
Timekeeping
• Resetting the seconds to
while the current count is in the range of 30 to 59
causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are
reset to
without changing the minutes.
• The year can be set in the range of 2000 to 2099.
• The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to change
it except when battery has replaced.
• The current time for all city codes in the Timekeeping Mode and World Time Mode is
calculated in accordance with the Coordinated Universal Time (UTC) for each city,
based on your Home City time setting.
E-57
Illumination Precautions
• Illumination may be difficult to see when viewed under direct sunlight.
• Illumination turns off automatically whenever an alarm sounds.
• Illumination turns off automatically depends on the current illumination duration
setting.
• Frequent use of illumination runs down the battery.
Auto light switch precautions
• Avoid wearing the watch on the inside of your wrist. Doing so causes the auto light
switch to operate when it is not needed, which shortens battery life. If you want to
wear the watch on the inside of your wrist, turn off the auto light switch feature.
More than 15 degrees
too high
E-58
• Illumination may not turn on if the face of the watch is
more than 15 degrees above or below parallel. Make
sure that the back of your hand is parallel to the ground.
• Illumination turns off in about 1.5 seconds or 3 seconds,
even if you keep the watch pointed towards your face.
E-59
Operation Guide 5299
• Static electricity or magnetic force can interfere with proper operation of the auto
light switch. If illumination does not turn on, try moving the watch back to the starting
position (parallel with the ground) and then tilt it back toward you again. If this does
not work, drop your arm all the way down so it hangs at your side, and then bring it
back up again.
• Under certain conditions, illumination may not turn on until about one second after
you turn the face of the watch towards you. This does not necessarily indicate
malfunction of the auto light switch.
• You may notice a very faint clicking sound coming from the watch when it is shaken
back and forth. This sound is caused by mechanical operation of the auto light
switch, and does not indicate a problem with the watch.
Specifications
Accuracy at normal temperature: ± 15 seconds a month
Digital Timekeeping: Hour, minutes, seconds, p.m. (PM), month, day, day of the week
Time format: 12-hour and 24-hour
Calendar system: Full Auto-calendar pre-programmed from the year 2000 to 2099
Other: Home City code (can be assigned one of 48 city codes); Standard Time /
Daylight Saving Time (summer time)
Analog Timekeeping: Hour, minutes (hand moves every 20 seconds)
Thermometer:
Measurement and display range: –10.0 to 60.0°C (or 14.0 to 140.0°F)
Display unit: 0.1°C (or 0.2°F)
Measurement intervals: 2 seconds for the first 2 minutes, 2 minutes thereafter
Other: Calibration; Manual measurement (button operation)
Temperature Sensor Precision:
±2°C (±3.6°F) in range of –10°C to 60°C (14.0°F to 140.0°F)
Tide/Moon Data: Moon phase indicator for specific date; Moon age; Tide for specific
date and time
Other: High tide time adjustment; Moon phase reversal
E-60
E-61
Stopwatch:
Measuring unit: 1/100 second
Measuring capacity: 999:59'59.99"
Measuring modes: Elapsed time, Split time
Countdown Timer:
Measuring unit: 1 second
Input range: 1 minute to 24 hours (1-minute increments)
World Time: 48 cities (29 time zones)
Other: Daylight Saving Time/Standard Time, Home City/World Time City Swapping
Alarms: 5 daily alarms (with 1 snooze alarm), Hourly Time Signal
Illumination: LED (light-emitting diode), Auto Light Switch; Selectable illumination
duration
Other: Button operation tone on/off
City Code Table
Battery : Two silver oxide batteries (Type: SR927W)
Approximate Battery Life: 3 years on type SR927W
(ten seconds of alarm operation per day, one illumination operation (1.5 seconds)
per day)
E-62
L-1
City Code Table
City
Code
PPG
HNL
ANC
YVR
LAX
YEA
DEN
MEX
CHI
NYC
SCL
YHZ
YYT
City
Pago Pago
Honolulu
Anchorage
Vancouver
Los Angeles
Edmonton
Denver
Mexico City
Chicago
New York
Santiago
Halifax
St. Johns
UTC Offset/
GMT Differential
–11
–10
–9
–8
–7
–6
–5
–4
–3.5
City
UTC Offset/
City
Code
GMT Differential
RIO Rio De Janeiro
–3
FEN Fernando de Noronha
–2
–1
RAI
Praia
UTC
0
LIS
Lisbon
LON
London
MAD
Madrid
PAR
Paris
ROM
Rome
+1
BER
Berlin
STO
Stockholm
ATH
Athens
CAI
Cairo
+2
JRS
Jerusalem
L-2
• This table shows the city codes of this watch.
• The rules governing global times (UTC offset and GMT differential) and summer
time are determined by each individual country.
L-4
City
Code
MOW*
JED
THR
DXB
KBL
KHI
DEL
KTM
DAC
RGN
BKK
City
Moscow
Jeddah
Tehran
Dubai
Kabul
Karachi
Delhi
Kathmandu
Dhaka
Yangon
Bangkok
UTC Offset/
GMT Differential
+3
+3.5
+4
+4.5
+5
+5.5
+5.75
+6
+6.5
+7
City
Code
SIN
HKG
BJS
TPE
SEL
TYO
ADL
GUM
SYD
NOU
WLG
City
Singapore
Hong Kong
Beijing
Taipei
Seoul
Tokyo
Adelaide
Guam
Sydney
Noumea
Wellington
UTC Offset/
GMT Differential
+8
+9
+9.5
+10
+11
+12
* The above is current as of June 2012. This watch does not reflect the change in the
Moscow (MOW) time offset to +4. Because of this, you should leave the summer
time setting turned on (which advances the time by one hour) for Moscow (MOW).
L-3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement