Casio Signature XJ-M140 User's Manual

Casio Signature XJ-M140 User's Manual
EFS
DATA PROJECTOR
XJ-M140 / XJ-M145*
XJ-M150 / XJ-M155*
XJ-M240 / XJ-M245*
XJ-M250 / XJ-M255*
* USB port models
* Modèles à port USB
* Modelos con puerto USB
English
Setup Guide
Be sure to keep all user documentation
handy for future reference.
To obtain the latest version of this
manual visit the website at the URL
below.
http://www.casio.com/support/
Français
Guide d’installation
Conservez la documentation à portée de
main pour toute référence future.
Español
Guía de configuración
Asegúrese de tener a mano toda la
documentación del usuario para
futuras consultas.
• Some models covered by this User’s Guide may not be available
in certain geographic areas.
• Certains modèles couverts par ce mode d’emploi peuvent ne
pas être commercialisés dans certaines zones géographiques.
• Algunos modelos cubiertos por esta Guía del usuario pueden no
estar disponibles en determinadas áreas geográficas.
Contents
Safety Precautions ..................................... E-1
Starting and Stopping Projection ............E-14
Operating Precautions ............................... E-7
To start projection ....................................... E-14
To turn off the projector .............................. E-15
About the Light Source Unit...........................E-7
Laser Precautions ..........................................E-7
Other Precautions ..........................................E-8
Precaution when Handling the
Projector after Use .........................................E-9
Stowing the Projector in the Carrying Bag.....E-9
Cleaning the Projector....................................E-9
Using the CD-ROM ...................................E-16
To view the contents of a
User’s Guide (PDF) ...................................... E-16
Indicators ...................................................E-17
Troubleshooting ........................................E-18
Main Specifications...................................E-20
Unpacking ................................................. E-10
General Guide ........................................... E-10
Getting Ready ........................................... E-11
Loading Remote Controller Batteries...........E-11
Setting Up the Projector...............................E-11
Setup Precautions........................................E-12
Changing the Projector Elevation Angle ......E-12
Connecting a Computer to the Projector .....E-13
z DLP is a registered trademark of Texas Instruments Incorporated of the United States.
z Microsoft, Windows, Windows Vista, and PowerPoint are registered trademarks or trademarks of Microsoft
Corporation in the United States and other countries.
z HDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks or registered trademarks of
HDMI Licensing, LLC.
z Apple and Macintosh are registered trademarks of Apple Inc. of the United States.
z Adobe and Reader are registered trademarks of Adobe Systems Incorporated.
z XGA is a registered trademark of IBM Corporation of the United States.
z ArcSoft and the ArcSoft logo are trademarks or registered trademarks of ArcSoft, Inc. in the United States
and other countries.
z Other company and product names may be registered trademarks or trademarks of their respective
owners.
z The contents of this User’s Guide are subject to change without notice.
z Copying of this manual, either in part or its entirety, is forbidden. You are allowed to use this manual for your
own personal use. Any other use is forbidden without the permission of CASIO COMPUTER CO., LTD.
z CASIO COMPUTER CO., LTD. shall not be held liable for any lost profits or claims from third parties arising
out of the use of this product or this manual.
z CASIO COMPUTER CO., LTD. shall not be held liable for any loss or lost profits due to loss of data caused
by malfunction or maintenance of this product, or any other reason.
z The sample screens shown in this manual are for illustrative purposes only, and may not be exactly the
same as the screens actually produced by the product.
B
E
Safety Precautions
Thank you for selecting this CASIO product. Be sure to read these “Safety Precautions” before trying to
use it. After reading this User’s Guide, keep it in a safe place for future reference.
About safety symbols
Various symbols are used in this User’s Guide and on the product itself to ensure safe use, and to
protect you and others against the risk of injury and against material damage. The meaning of each of the
symbols is explained below.
*Danger
*Warning
*Caution
This symbol indicates information that, if ignored or applied incorrectly,
creates the risk of death or serious personal injury.
This symbol indicates information that, if ignored or applied incorrectly, could
possibly create the risk of death or serious personal injury.
This symbol indicates information that, if ignored or applied incorrectly, could
possibly create the risk of personal injury or material damage.
Icon Examples
’
!
$
A triangle indicates a situation against which you need to exercise caution. The example shown
here indicates you should take precaution against electric shock.
A circle with a line through it indicates information about an action that you should not perform.
The specific action is indicated by the figure inside the circle. The example shown here means
disassembly is prohibited.
A black circle indicates information about an action that you must perform. The specific action
is indicated by the figure inside the circle. The example shown here indicates you must unplug
the power cord from the power outlet.
● Malfunction
Precautions During Use
-
* Warning
● Smoke, odor, heat, and other
abnormalities
-
Should you ever notice smoke, strange
odor, or any other abnormality,
immediately stop using the projector.
Continued use creates the risk of fire and
electric shock. Immediately perform the
following steps.
1. Unplug the projector.
2. Contact your original dealer or authorized
CASIO service center.
Immediately stop using the projector if
the screen appears abnormal, or if any
other abnormal operation occurs even
though you are operating the projector
correctly. Continued use creates the risk
of fire and electric shock. Immediately
perform the following steps.
1. Turn off the projector.
2. Unplug the projector.
3. Contact your original dealer or authorized
CASIO service center.
E-1
Safety Precautions
● Power cord
+
● Water and foreign matter
Misuse of the power cord creates the risk
of fire and electric shock.
Make sure that you always observe the
following precautions.
• Be sure to use only the accessories that come
with the projector.
• Make sure that you use a power source with the
same voltage as that specified for the projector.
• Do not overload a power outlet with too many
devices.
• Do not locate the power cord near a stove.
• Do not use the power cord that comes with the
projector with any other device.
• Do not share the outlet supplying power to the
projector with other devices. If you are using an
extension cord, make sure that the ampere rating
of the extension cord is compatible with the
power consumption value of this projector.
• Never use the power cord while it is still bundled
together.
• Use a conveniently located power outlet that you
can reach easily when you need to unplug the
projector.
A damaged power cord creates the risk
of fire and electric shock.
Make sure that you always observe the
following precautions.
• Never place heavy objects on the power cord
and never expose it to heat.
• Make sure the power cord is not pinched
between the wall and the rack or table where the
projector is located, and never cover the power
cord with a cushion or other object.
• Never try to modify the power cord, allow it to
become damaged, or subject it to excessive
bending.
• Do not twist the power cord or pull on it.
Never touch the power cord or plug while
your hands are wet.
Doing so creates the risk of electric
shock.
• When using this projector in the country where
you purchased it, be sure to use the power cord
that came with it. Whenever using the projector
in another country, be sure to purchase and use
a power cord that is rated for the voltage of that
country. Also make sure that you are aware of
the Safety Standards that apply in that country.
When going out, make sure the projector
is in a location away from pets and other
animals, and unplug the power plug from
the power outlet. A power cord damaged
by chewing can cause shorts, and
creates the risk of fire.
-
"
+
%
%
Never allow water to get on the projector.
Water creates the risk of fire and electric
shock.
Never place a vase or any other container
of water on top of the projector. Water
creates the risk of fire and electric shock.
Water or other liquid, or foreign matter
(metal, etc.) getting into the projector
creates the risk of fire and electric shock.
Should anything get inside the projector,
immediately perform the following steps.
1. Turn off the projector.
2. Unplug the projector.
3. Contact your original dealer or authorized
CASIO service center.
● Disassembly and modification
!
Never try to take the projector apart or
modify it in any way. The projector
contains a large number of high-voltage
components that create the risk of
electric shock and burn injury. Also, note
that problems caused by unauthorized
projector disassembly or modification are
not covered by the warranty and are not
eligible for repair by CASIO.
Be sure to leave all internal inspection, adjustment,
and repair up to your original dealer or authorized
CASIO service center.
● Dropping and impact
-
Continued use of the projector after it has
been damaged by dropping or other
mistreatment creates the risk of fire and
electric shock. Immediately perform the
following steps.
1. Turn off the projector.
2. Unplug the projector.
3. Contact your original dealer or authorized
CASIO service center.
-
E-2
Safety Precautions
● Disposal by burning
-
● Exhaust vents
Never try to dispose of the projector by
burning it. Doing so can cause an
explosion, which creates the risk of fire
and personal injury.
● Looking into the lens or vents while
light source unit is on
-
Never look directly into the lens or vents
while light source unit is on. The strong
light emitted by the projector creates the
risk of eye damage.
● Blocking the vents
-
Never allow the vents to become
blocked. Doing so causes internal heat
build up, which creates the risk of fire and
breakdown of the projector. Touching the
projector while it is hot creates the risk of
burn injury. Make sure that you always
observe the following precautions.
• Allow at least 30cm (11.8 inches) between the
projector and walls.
• Do not insert the projector into any space where
air circulation is poor.
• Never cover the projector with a blanket or any
similar item.
• Locate the projector on a firm, flat surface during
use. Never use the projector while it is on a
carpet, blanket, towel, seat cushion, or other
pliable surface.
• Never stand the projector up on either end during
use.
Be sure to remove the lens cover before turning on
the projector. Never leave the lens cover attached
while the projector is in use.
● Location
Never locate the projector in any of the following
types of locations. Doing so creates the risk of fire
and electric shock.
• Near an area subject to strong vibration
• An area subject to large amounts of moisture or
dust
• In a kitchen or other area exposed to oil smoke
• Near a heater, on a heated carpet, or in an area
exposed to direct sunlight
• An area subject to temperature extremes
(Operating temperature range is 5°C to 35°C
(41°F to 95°F)).
● Heavy objects
Never place heavy objects on the projector or
climb on top of the projector. Doing so creates the
risk of fire and electric shock.
Never locate the projector in a bathroom or
anywhere else there is the chance that it will be
splashed with water.
Never open the projector’s cabinet.
Doing so creates the risk of electric
shock.
● Unstable location
● Cleaning
$
● Lens cover
● Water
● Projector cabinet
’
The exhaust vents become very hot while the
projector is running. Never touch them. Doing so
creates the risk of burn injury. The areas near the
exhaust vents also become quite hot. Never locate
objects made of plastic or other heat-sensitive
materials near or under the projector. Doing so
creates the risk of deformation and discoloration of
the object.
Before cleaning the projector, be sure to
turn it off and unplug it from the power
outlet. Failure to do so creates the risk of
electric shock.
-
E-3
Never place the projector on an unstable
surface or on a high shelf. Doing so can
cause it to fall, creating the risk of
personal injury.
Safety Precautions
● Using the projector on a base with
casters
* Caution
Whenever using the projector on a base that has
casters, make sure that you lock the casters when
not moving the base.
● Lightening
During a lightening storm, do not touch the plug of
the projector’s power cord.
● Remote controller
!
+
Never try to take the remote controller
apart or modify it in any way. Doing so
creates the risk of electric shock, burn
injury, and other personal injury. Be sure
to leave all internal inspection,
adjustment, and repair up to your original
dealer or authorized CASIO service
center.
Never allow the remote controller to
become wet. Water creates the risk of fire
and electric shock.
● Radio waves emitted by the wireless
adapter (which is provided with some
projector models)
-
Never use this product inside of an
aircraft or medical facility, or in any other
location where use of such devices is
prohibited. Radio waves can have an
effect on the operation of electronic
equipment and medical equipment, and
cause accidents.
Do not use this product in the vicinity of
high-precision electronic instruments or
electronic devices that handle weak radio
signals. Radio waves can have an effect
on the operation of such equipment, and
cause accidents.
• If you are using a pace maker or any other
electronic medical device, be sure to consult
your physician or device manufacturer before
using this product.
-
● Power cord
-
Misuse of the power cord creates the risk
of fire and electric shock. Make sure that
you always observe the following
precautions.
• When unplugging the power cord, always grasp
the plug, and do not pull on the power cord.
• Insert the plug into the power outlet as far as it
will go.
• After using the projector, unplug it from the
power outlet.
• Unplug the projector from the power outlet if you
do not plan to use it for a long time.
• At least once a year, unplug the power plug and
use a dry cloth or vacuum cleaner to clear dust
from the area around the prongs of the power
plug.
• Never use detergent to clean the power cord,
especially the power plug and jack.
• Before moving the projector, be sure to turn it off
and unplug it from the power outlet first.
● Backup of important data
+
Be sure to keep separate written records
of all data stored in projector memory.
Memory data can be lost due to
breakdown, maintenance, etc.
● During projection, make sure there is
nothing in front of the lens blocking
the light.
An object in front of the lens creates the risk of fire.
● Lens effect
Never have an aquarium or any other object that
produces a lens effect in front of the projector
while the light source unit is on. Such an object
creates the risk of fire.
● Lens
Never touch the lens with your hand.
● Wireless adapter (provided with some
projector models)
-
E-4
Keep the wireless adapter out of the
reach of small children. Accidental
swallowing of a wireless adapter can
interfere with proper breathing and create
a life-threatening situation.
Safety Precautions
Battery Precautions
Other
* Danger
* Caution
+
Should liquid leaking from an alkaline
battery get into the eyes, immediately take
the following steps.
1. Do not rub the eyes! Wash the eyes with clean
water.
2. Contact a physician immediately. Failure to
take immediate action can lead to loss of
eyesight.
Allowing dust to build up inside the projector for
long periods without cleaning creates the risk of
fire and breakdown. Contact your original dealer or
authorized CASIO service center once a year about
having the interior of the projector cleaned. Note
that you will be charged for cleaning.
* Warning
Misuse of batteries can cause them to leak and
stain the area around them, or to explode, creating
the risk of fire and personal injury. Make sure that
you always observe the following precautions.
• Never try to take batteries apart and do
not allow them to become shorted.
• Never expose batteries to heat or throw
them into fire.
• Never mix old batteries and new ones.
• Never mix batteries of different types.
• Never try to charge batteries.
• Take care that batteries are oriented
correctly when you load them.
+
* Caution
Misuse of batteries can cause them to leak and
stain the area around them, or to explode, creating
the risk of fire and personal injury. Make sure that
you always observe the following precaution.
• Use only the type of batteries that is
specified for the remote controller.
-
● Dead batteries
Be sure to remove batteries from the remote
controller as soon as they go dead.
• Remove batteries from the remote
controller if you do not plan to use it for a
long time.
+
● Disposing of batteries
Make sure that you dispose of used batteries in
accordance with the rules and regulations in your
local area.
E-5
Safety Precautions
+
3D Glasses
* Warning
-
3D images should not be viewed by the
types of individuals described below.
Doing so creates the risk of loss of
health.
• Individuals with heart disease
• Individuals with a history of photodermatosis
• Individuals with epileptic tendencies
* Caution
-
Do not view 3D images if you are
experiencing any of the symptoms
described below.
• When you are in poor physical condition
• When you feel you are losing your health
• Should you ever experience fatigue, loss of
health, or abnormal feelings while watching 3D
images, stop watching. Continued watching
could damage your health.
• Should the 3D image ever start appearing double
or lose its three-dimensionality, stop watching.
Continued watching can cause eye fatigue.
+
Avoid watching 3D images for very long
periods. Doing so can cause eye fatigue.
Be sure to observe the following
precautions when watching 3D images.
● Take care about nearby people and
objects.
Viewing 3D images can interfere with distance
judgment, so you should take care about nearby
people and objects when extending your arms or
making sudden movements. Failure to do so
creates the risk of material damage and personal
injury.
● Use 3D glasses when viewing 3D
images.
Watching 3D images without 3D glasses can cause
eye fatigue. Always use the specified 3D glasses
whenever viewing 3D images.
● You need to wear your glasses or any
other devices you normally use for
vision correction.
If you normally wear glasses or contact lenses, you
should be wearing them when you watch 3D
images with the 3D glasses. Failure to do so
creates the risk of eye fatigue or abnormal vision.
E-6
The normal minimum age for viewing 3D
images is six. When 3D images are being
watched by a small child, a competent
adult should be on hand to monitor the
child, to ensure that the 3D images are
suitable for the child, that the child does
not watch the 3D images for too long an
uninterrupted period, etc.
Operating Precautions
About the Light Source Unit
z The projector’s light source unit uses a laser and LED.
z The life of the light source unit is rated at approximately 20,000 hours. The actual life will depend on
use conditions, the settings configured on the setup menu, and differences between each individual
light source unit.
z The light source unit is warranted for the period noted on the warranty certificate or for 6,000 hours,
whichever comes first.
z The failure of the light source unit to light or a noticeable drop in light source unit brightness indicates
the end of the light source unit’s life. Contact your original dealer or authorized CASIO service center
for replacement. Note that problems caused by unauthorized projector disassembly or modification
are not covered by the warranty and are not eligible for repair by CASIO.
Laser Precautions
This projector is a Class 1 laser device that conforms with IEC 60825-1.
z This projector has a built-in laser module. Disassembly or modification is very dangerous and should
never be attempted.
z Any operation or adjustment not specifically instructed by the user’s guide creates the risk of
hazardous laser radiation exposure.
Bottom
E-7
Operating Precautions
Other Precautions
This projector is made of precision components. Failure to observe the following precautions can result
in inability to correctly save data and malfunction.
● Never use or store the projector in the following locations. Doing so creates the
risk of malfunction of and damage to the projector.
z
z
z
z
z
z
z
Locations subjected to electrostatic charge
Locations subjected to temperature extremes
Locations where there is extreme moisture
Locations subjected to sudden temperature changes
Locations where there is a lot of dust
On a shaky, slanted, or otherwise unstable surface
Locations where there is the danger of getting wet
● Avoid using the projector under the following conditions. Such conditions
create the risk of malfunction of and damage to the projector.
z Avoid areas subject to temperature extremes (operating temperature
range is 5°C to 35°C (41°F to 95°F)).
z Never place heavy objects on the projector or climb on top of the
projector.
z Never insert or allow foreign objects to drop into the projector.
z Never place a vase or any other container of water on top of the
projector.
● Whenever setting the projector down or performing any operation that involves
moving or reorienting it, take care that you do not pinch your fingers under the
projector.
● Never leave a dead battery inside the remote controller for a long time.
A dead battery can leak, which leads to malfunction of and damage to the remote controller.
● Clean with a soft, dry cloth.
When very dirty, use a soft cloth that has been dampened in a weak solution of water and a mild neutral
detergent. Wring all excess water from the cloth before wiping. Never use thinner, benzine, or any other
volatile agent to clean the projector. Doing so can remove its markings and cause staining of the case.
● Missing Screen Dots
Though this projector is manufactured using the most advanced digital technology available today, some
of the dots on the screen may be missing. This is normal, and does not indicate malfunction.
● Never subject the projector to strong impact while it is projecting.
If the projector is accidentally subjected to strong impact, the projection image will momentarily go
blank. The image will reappear after some time, but it may be the wrong color or it may be accompanied
by an error message.
If the projected image is the wrong color, re-select the current input source. If this does not return the
projected image to its proper color, use the procedure under “To turn off the projector” on page E-15 to
turn projector power off and then back on again.
If the image reappears with an error message, correct the problem in accordance with the indicator
explanations under “Error Indicators and Warning Messages” in the User’s Guide on the CD-ROM that
comes with the projector.
E-8
Operating Precautions
● Keystone Correction and Image Quality
Performing keystone correction causes the image to be compressed before it is projected. This can
result distortion of the image or a loss of image quality. If this happens, change orientation of the
projector and/or screen so it conforms as much as possible to the illustration under “Setting Up the
Projector” on page E-11.
If image quality is the highest priority, turn off auto keystone correction and position the projector so it is
pointed straight at the screen.
z Even if your projector is still within the warranty period, you will be charged for repair if a problem is
due to running the projector non-stop for very long periods (like 24 hours) or if the projector was set up
and used without following the “Setup Precautions” on page E-12 of this manual.
Precaution when Handling the Projector after Use
The projector’s exhaust vents and the area around the vents
become very hot during operation, and will still be hot immediately
after turning off the projector. Because of this, you should hold the
sides of the projector as shown in the illustration whenever
moving it.
Stowing the Projector in the Carrying Bag
Make sure the projector is no longer warm before stowing it in the carrying bag.
Cleaning the Projector
z Periodically clean the projector exterior, lens, intake vents, exhaust vents, and airflow vents on a
regular basis.
z Dust and dirt tend to collect around the intake vents. Because of this, you should use a vacuum
cleaner to clean away accumulated dust and dirt periodically.
z Continued use of the projector after dust has accumulated around the intake vents can cause
overheating of internal components and lead to malfunction.
z Certain operating conditions also can cause dirt and dust to accumulate around the projector’s
exhaust vents and airflow vents. If this happens, use the same procedure as that described above to
clean the exhaust vents and airflow vents.
E-9
Unpacking
As you unpack the projector, check to make sure that all of the items listed below are present.
•
•
•
•
•
•
•
•
DATA PROJECTOR
Remote Controller
(YT-120)
Test Batteries (AAA-size × 2)
AC Power Cord
Carrying Bag
CD-ROM
Setup Guide
“Read this first” Sheet
Warranty
Wireless adapter (Provided with models equipped with USB ports only.)
Mini D-Sub Cable
General Guide
CLASS 1 LASER PRODUCT
Control panel
Indicators
[P] (Power) key
Intake vents
Brightness
sensor
Exhaust
vents
Projection lens
Airflow vents
Remote control signal receiver
Lens cover
Zoom ring
Focus ring
E-10
Getting Ready
Loading Remote Controller Batteries
Important!
z Be sure to use alkaline batteries only.
*Caution
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
1. Open the battery cover on the back of
2. Load two new batteries into the case,
the remote controller.
making sure that their positive (+) and
negative (–) ends are facing correctly.
3. Close the battery cover on the back of the remote controller.
Replacing Remote Controller Batteries
Open the battery cover on the back of the remote controller, replace the old batteries with new ones, and
then close the battery cover.
Important!
z To avoid running down the batteries, store the remote control unit so its buttons are not
pressed inadvertently.
Setting Up the Projector
Locate the projector on a desk, table, or stand that is firm and level. Make sure to allow sufficient space
around the sides and back of the projector for proper ventilation. The following illustrations show how the
projector should be oriented for optimum projection relative to the screen.
XJ-M140/XJ-M145/XJ-M150/XJ-M155
XJ-M240/XJ-M245/XJ-M250/XJ-M255
Screen
Screen
Make sure the projector is at a right angle to the screen.
Position the projector so the lens side is at the edge of the
table, etc.
z The projector can be configured for projection from the back of a screen. For details, see the User’s
Guide on the CD-ROM that comes with the projector.
E-11
Getting Ready
Setup Precautions
z Use a conveniently located power outlet that you can reach easily when you need to unplug the
projector.
z Do not allow any objects to be within the area indicated by the dashed line below, which is an area
within 30cm (11.8 inches) of the projector. Keep all obstacles and other objects at least 30cm away
from the projector’s vents.
z Airflow from air conditioning equipment can blow the heat being exhausted from the area around the
projector’s lens in a way that causes heat ripples to appear in the projected image. If this happens,
adjust the airflow of the air conditioning equipment or move the projector.
Intake vents
Exhaust vents
30cm
(11.8 inches)
Airflow vents
Changing the Projector Elevation Angle
1. Lift up the front of the projector and press the release button 1.
z This will cause the front foot 2 to extend from the projector.
2
1
3
2. While holding down the release button, raise and lower the front of the projector.
When the front foot is approximately the height you want, release the release
button.
z The front foot will lock at the position where you release the release button.
E-12
Getting Ready
3. Make fine adjustments to the elevation angle of the projector by rotating the front
foot.
4. Make fine adjustments to the horizontal tile of the projector by rotating the rear feet
3.
Important!
z To retract the front foot, hold down the release button and slide the front foot back into the
projector. Never try to forcibly change the front foot position without pressing the release
button.
Connecting a Computer to the Projector
Connect the projector’s COMPUTER IN terminal to the RGB terminal of a computer as shown in the
illustration below.
<Projector>
COMPUTER IN
terminal
<Computer>
Bundled mini D-Sub cable
AUDIO IN terminal
To monitor terminal
(analog RGB output terminal)
To line output
terminal
Audio cable (commercially available)
Important!
z Always turn off the projector and the computer before connecting them.
z Take care so the volume level of the computer is not set too high.
NOTE
z To connect to an external input source other than a computer (video device, etc.), see the User’s
Guide on the CD-ROM that comes with the projector.
E-13
Starting and Stopping Projection
To start projection
1. Use the bundled AC power cord to plug the projector into a power outlet.
NOTE
z This product is also designed for IT power distribution system with phase-to-phase voltage 230V.
2. Turn on the computer that is connected to the projector.
3. If the projector lens cover is covering the lens, remove it.
z To remove the lens cover, insert your fingers into its recesses and squeeze towards the middle.
4. Press the [P] (Power) key.
z The first time you turn on the projector, a “Language” window will appear in the center of the
projection screen. Select the language you want.
5. Select the input source
z Press the [INPUT] key to display a list of input sources. Use the [T] and [S] keys to select
“Computer” and then press the [ENTER] key.
6. Adjust the size and the focus of the projected image.
z Use the zoom ring of the projector’s lens to adjust the size of the projected image, and the focus
ring to adjust the focus.
Zoom ring
Smaller
Larger
Focus ring
NOTE
z The projector has a keystone correction feature that
prevents distortion of the projected image when projecting
from an angle. The projector detects when it is at a vertical
angle to the screen and performs keystone correction
automatically.
You can use the [KEYSTONE +] and [KEYSTONE –] keys to
adjust keystone correction manually.
E-14
Starting and Stopping Projection
To turn off the projector
1. Press the [P] (Power) key.
z This causes the confirmation message to appear. If you do not turn off the projector the
confirmation message will disappear automatically after about 10 seconds. The confirmation
message will also disappear if you press the [ESC] key.
2. To turn off the projector, press the [P] (Power) key again in response to the
confirmation message.
3. After checking to make sure that the POWER/STANDBY indicator has stopped
flashing amber and remains lit, unplug the AC power cord from the power outlet.
E-15
Using the CD-ROM
The CD-ROM contains software for each projector model and PDF files with User’s Guides. In order to
read the User’s Guide, you need to have Adobe® Reader® installed on your computer.
To view the contents of a User’s Guide (PDF)
1. Place the CD-ROM that comes with the projector into your computer’s CD-ROM
drive.
2. Perform either of the following operations.
z If the CD-ROM menu screen appears:
1 On the menu screen, click the [Open Folder] button to the right of “User’s Guide”.
2 When the User’s Guide folder opens, open the folder that corresponds to the language you
want to use.
z If the CD-ROM menu screen does not appear:
1 On your computer, navigate to the CD-ROM and then open it.
2 Open the User’s Guide folder and then open the folder that corresponds to the language you
want to use.
3. Double-click the name of the manual you want to view.
Manual Name
Description
File Name
User’s Guide
Contains detailed information about the projector.
UsersGuide_English.pdf
USB Function Guide
(USB port models
only)
Explains operations when connecting USB
memory, a CASIO Multi Projection Camera
(YC-400, YC-430), or a graphic scientific calculator
to the USB port on the back of the projector.
USB_Guide_English.pdf
Wireless Function
Guide
(USB port models
only)
Explains operations when establishing a wireless
LAN connection between the projector and a
computer and projecting the computer’s display
contents.
WirelessGuide_English.pdf
z Double-clicking a file name starts up Adobe Reader and displays the contents of the applicable
manual.
z On some systems, the “.pdf” extension may not be displayed at the end of the file name.
Installing the Software (USB port models only)
The software described in the table below can be installed from the CD-ROM menu screen that appears
when you place the CD-ROM that comes with the projector into your computer’s CD-ROM drive. For
details about installing the software, see the manuals in the “Refer to:” column of the table.
Description
Refer to:
Wireless Connection 3
Software Name
Software that makes it possible to establish a
wireless connection between a projector and
computer.
Wireless Function Guide
(WirelessGuide_English.pdf)
EZ-Converter FA
Software that converts PowerPoint files to
ECA or PtG files.
USB Function Guide
(USB_Guide_English.pdf)
ArcSoft MediaConverter 3 for
CASIO Projector
Software for converting movie files.
Multi Projection Camera
Update Software
Software for updating the firmware of the
YC-400 Multi Projection Camera.
E-16
Indicators
Indicators keep you informed about the current operational status of the projector. The following shows
what the indicators look like when operation is normal.
When the indicators
appear like this:
POWER/
STANDBY
LIGHT
TEMP
Amber
Amber
Amber
You have just plugged the AC power cord into a power outlet. Wait until
the projector enters the standby state (see below) before trying to turn on
power.
Standby state: The AC power cord is plugged in and the projector is in
standby.
Projector is warming up after being turned on.
Amber
Green
It means this:
Amber
Amber
Projector is on and standing by for use.
Green
Projector is performing internal power down processes.
Amber
Green
: Lit
“On (Auto)” or “On (Manual)” is selected for the projector’s Eco Mode
setting.
Green
: Flashing
: Unlit
z When a warning message appears on the projection screen, or when the POWER, TEMP, and LIGHT
indicators are lit or flashing in a pattern other than those shown above, it means that a projector error
has occurred. For details about indicators and warning messages, see the User’s Guide on the
CD-ROM that comes with the projector.
E-17
Troubleshooting
Check the following items whenever you experience any problem with the projector.
Problem
Power does not turn
on.
No image is projected
or the projected image
is abnormal.
Image color or display
is very abnormal.
I can’t understand
messages or menus
because they are the
wrong language.
No sound
B
Cause and Recommended Action
z If the POWER/STANDBY indicator is not lit, the AC power cord is not
connected correctly. Connect the AC power cord correctly.
z If the TEMP or LIGHT indicator remains flashing or lit, it means some type
of error has occurred. See “Error Indicators and Warning Messages” in the
User’s Guide (UsersGuide_English.pdf).
z The computer or video device connected to the projector is not turned on
or it is not outputting a video signal. Make sure the connected computer or
video device is turned on, and perform the required operation on it to
output a video signal.
z The correct output source is not selected on the projector. On the
projector, select the correct input source that corresponds to the
connected device.
z Images may not project correctly when you have the component output
terminal of a video device connected to the COMPUTER IN terminal of the
projector. Connect to the VIDEO terminal or S-VIDEO terminal of the
projector.
The wrong option (“Component” or “RGB”) may be selected for the “Input
Settings J COMPUTER Terminal” setting on the setup menu. The image will
not be projected correctly if “Component” is selected while the projector’s
COMPUTER IN terminal is connected to the RGB output terminal of a
computer, or if “RGB” is selected while the projector’s COMPUTER IN
terminal is connected to the component video output terminal of a video
device. On the setup menu, select “Auto” for the “Input Settings J
COMPUTER Terminal” setting. See the User’s Guide
(UsersGuide_English.pdf).
Perform the following operation to select the language you want. See the
User’s Guide (UsersGuide_English.pdf).
1. Press the [MENU] key to display the setup menu.
2. If the input signal is HDMI, press [T] four times and then press the
[ENTER] key. If the input signal is not HDMI, press [T] five times and then
press the [ENTER] key.
3. Press [S] twice and then press the [ENTER] key to display the language
selection menu.
4. Use the [T] and [S] keys to move the highlighting to the language you
want to select and then press the [ENTER] key.
5. Press the [MENU] key to exit the setup menu.
z The projector’s volume level setting may be too low or muted. Press the
remote controller [VOLUME] key and then use [T] and [S] to adjust the
volume level. See the User’s Guide (UsersGuide_English.pdf).
z The volume level setting of the device connected to the projector is too low
or the other device is not outputting audio. Adjust the volume level of the
connected device.
z The audio output of the connected device may not be connected correctly
to the projector’s AUDIO IN terminal or AUDIO IN L/R terminal. Check the
connection, referring to one of the following (depending on the type of
connected device): “Connecting a Computer to the Projector” in this
manual or “Connecting to a Video Device” in the User’s Guide
(UsersGuide_English.pdf)
z “Line” is selected for the setup menu “Option Settings 2 J Audio Out”
setting. Change the “Audio Out” setting to “Speaker”. See the User’s
Guide (UsersGuide_English.pdf).
E-18
Troubleshooting
Problem
Strange color
Text is blurry.
The message “Please
input the password.”
appears and further
operation is not
possible.
The remote controller
does not work.
The TEMP or LAMP
indicator is flashing or
lit.
The light source unit
does not light.
Cause and Recommended Action
The input signal may not match projector settings. Try doing the following.
See the User’s Guide (UsersGuide_English.pdf).
–Use the [BRIGHT] key to adjust image brightness.
–Use the [COLOR MODE] key to change the color mode.
–On the setup menu, use “Image Adjustment 1 J Color Balance” to adjust
the projection image color balance.
z The image may be out of focus. Rotate the focus ring to focus.
z The current frequency and/or phase setting do not match the input signal.
(Applies only when the input source is an RGB signal.) Press the [AUTO]
key to execute an automatic adjustment operation.
z On the setup menu, perform the “Image Adjustment 2 J Frequency” and
“Image Adjustment 2 J Phase” adjustments. (Applies only when the input
source is an RGB signal.) See the User’s Guide (UsersGuide_English.pdf).
z If the input source is a video camera or document camera, check to make
sure there is no problem with the input source device.
The “Option Settings 1 J Power On Password” setting on the setup menu is
turned on, so the projector is password protected. Input the correct
password, and then press the [ENTER] key. See the User’s Guide
(UsersGuide_English.pdf).
z The remote controller batteries may be dead. Replace the batteries.
z The remote controller may be too far from the projector. Make sure the
remote controller is within the allowable range when you operate it. See
the User’s Guide (UsersGuide_English.pdf).
An error occurred. See “Error Indicators and Warning Messages” in the
User’s Guide (UsersGuide_English.pdf).
The light source unit has reached the end of its service life or it is
malfunctioning. Contact your original dealer or authorized CASIO service
center for replacement.
Important!
z Try performing the following steps, which may or may not return the projector to normal
operation.
1. Unplug the AC power cord and wait for at least 10 minutes.
2. Plug the power cord back in and turn the projector back on again.
z If normal operation does not resume after you perform the above steps, take the projector to
your retailer or authorized CASIO service center.
E-19
Main Specifications
Model Name
Brightness
(ANSI Lumens)
Environment
Power
Approximate Dimensions
XJ-M140/XJ-M145/
XJ-M240/XJ-M245
XJ-M150/XJ-M155/
XJ-M250/XJ-M255
2500
3000
Operating Temperature: 5 to 35°C (41 to 95°F)
Operating Humidity: 20 to 80% (non-condensation)
Operating Altitude: 0 to 3,000 meters (0 to 10,000 feet) above sea level
Requirements 100-240V AC, 50/60Hz, 2.3A-1.0A
311 (W) × 244 (D) × 84 (H) mm
(12.2" × 9.6" × 3.3")
Weight
Approximately 3.9kg (8.6Ibs)
Specifications are subject to change without notice.
E-20
GUIDELINES LAID DOWN BY FCC RULES FOR USE OF THIS UNIT IN THE U.S.A. (not
applicable to other areas).
NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communication. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
z Reorient or relocate the receiving antenna.
z Increase the separation between the equipment and receiver.
z Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
z Consult the dealer or an experienced radio/TV technician for help.
FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
Proper connectors must be used for connection to host computer and/or peripherals in order to meet
FCC emission limits.
Connector cable....XJ-M140/XJ-M145/XJ-M150/XJ-M155/XJ-M240/XJ-M245/XJ-M250/XJ-M255 unit to
PC
Declaration of Conformity
Model Number: XJ-M140/XJ-M145/XJ-M150/XJ-M155/XJ-M240/XJ-M245/XJ-M250/XJ-M255
Trade Name: CASIO COMPUTER CO., LTD.
Responsible party: CASIO AMERICA, INC.
Address: 570 MT. PLEASANT AVENUE, DOVER, NEW JERSEY 07801
Telephone number: 973-361-5400
This device complies with Part 15 of the FCC Rules, Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
FCC Information
This device, IEEE 802.11g Wireless LAN USB Adapter, complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received; including interference that may cause undesired operation.
Federal Communications Commission (FCC) Statement
This Equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
—
—
—
—
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user authority to operate the
equipment.
Tested to comply with FCC standard. FOR HOME OR OFFICE USE.
FCC RF Radiation Exposure Statement:
1. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment,
under 47 CFR 2.1093 paragraph (d)(2).
2. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The IEEE 802.11g Wireless LAN USB Adapter has been tested to the FCC exposure requirements (Specific
Absorbtion Rate).
Tested To Comply With FCC Standards
FOR HOME OR OFFICE USE
FOR CALIFORNIA USA ONLY
Perchlorate Material – special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Manufacturer:
CASIO COMPUTER CO., LTD.
6-2, Hon-machi 1-chome, Shibuya-ku, Tokyo 151-8543, Japan
Responsible within the European Union:
CASIO EUROPE GmbH
Casio-Platz 1, 22848 Norderstedt, Germany
D
Printed in China
Imprimé en Chine
RJA524095-002
MA1202-D
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement