USB-1208FS-Plus/LS/1408FS-Plus Series

USB-1208FS-Plus/LS/1408FS-Plus Series
USB-1208FS-Plus/LS/1408FS-Plus Series
12-bit and 14-Bit Multifunction DAQ Devices
Features
• Low-cost USB DAQ devices
with 4 differential or 8 singleended analog inputs
• Maximum sample rates ranging
from 1.2 kS/s to 50 kS/s
• 2 analog outputs
• 16 digital I/O
• One 32-bit counter input
channel
• No external power required
• All devices available with
enclosure and screw terminals
• Board-only OEM versions of
-Plus devices also available
All devices in this series offer eight singled-ended or four differential analog inputs, two
analog outputs, 16 digital I/O, and one counter input. Eight of the digital I/O on the
USB-1208FS-Plus/1408FS-Plus can be used for high-current (24 mA) connections.
Supported Operating Systems
• Windows® 10/8/7/Vista®XP
32/64-bit
• Android™ (-Plus devices only)
Overview
The USB-1208FS-Plus/LS/1408FS-Plus Series consists of low-cost analog and digital
I/O devices. All devices in this series offer four differential (DIFF) or eight singleended (SE) analog inputs, two analog outputs, 16 digital I/O and one event counter.
The USB-1208LS offers sample rates up to 1.2 kS/s, while all USB-1208FS-Plus and
USB-1408FS-Plus devices (standard and OEM) offer sample rates up to 50 kS/s.
All devices in this series also support multiple software-selectable voltage input
ranges, making them ideally suited for a wide assortment of measurements.
USB-1208FS/LS/1408FS Series Selection Chart
Specification
USB-1208LS
USB-1208FS-Plus
USB-1208FS-Plus-OEM
USB-1408FS-Plus
USB-1408FS-Plus-OEM
Analog Input
8 SE/4 DIFF
8 SE/4 DIFF
8 SE/4 DIFF
Maximum Sample
Rate
1.2 kS/s
50 kS/s
48 kS/s max
Analog Output
2
2
2
Concurrent AI/AO
Scanning Operations
–
✔
✔
Digital Output
±2.5 mA per Pin
±6.0 mA per Pin (Port A)
±24.0 mA per Pin
(Port B)
±6.0 mA per Pin (Port A)
±24.0 mA per Pin
(Port B)
Event Counters
1
1
1
DAQami Support
✔
✔
✔
UL for Android
Support
–
✔
✔
Linux Support
✔
✔
✔
Matlab Support
✔
✔
✔
Measurement Computing
(508) 946-5100
1
Unless noted otherwise, all references to
the USB-1208FS-Plus and USB-1408FS-Plus
include their -OEM versions.
Analog Input
The USB-1208LS and USB-1208FS-Plus
provide eight, 11-bit SE analog inputs or
four, 12-bit DIFF analog inputs.
The USB-1408FS-Plus These devices provide eight, 13-bit SE analog inputs or four,
14-bit DIFF analog inputs.
All devices support software‑selectable
ranges that provide inputs from ±1 V to
±20 V in a DIFF configuration, and ±10 V
in a SE configuration.
Sample Rate
USB-1208LS: When scanning in hardwarepaced mode, the USB-1208LS can sample
at a maximum of 1.2 kS/s.
The device also supports BURSTIO mode
into the 4 kS FIFO at rates up to 8 kS/s.
USB-1208FS-Plus/1408FS-Plus: In hardware-paced mode, the USB-1208FS-Plus
can sample at a maximum of 50 kS/s,
and the USB-1408FS-Plus can sample at
a maximum of 48 kS/s.
[email protected]
mccdaq.com
USB-1208FS-Plus/LS/1408FS-Plus Series
Overview
Event Counter Input
Channel-Gain Queue
The channel-gain queue feature lets users configure a list of channels and gains for each scan. Each channel can have a different
gain setting. The gain settings are stored in a channel-gain queue
list that is written to local memory on the device.
Each device supports one 32-bit TTL-level counter that accepts
inputs up to 1 MHz.
External Clock I/O (-Plus devices only)
• The USB-1208LS channel-gain queue list can contain up
to eight channels in SE mode and up to four channels in
DIFF mode. The channels can be listed in any order.
The USB-1208FS-Plus and USB-1408FS-Plus have a bidirectional
external clock terminal. When configured for input, A/D conversions can be paced by an external source.
• The USB-1208FS-Plus/1408FS-Plus channel-gain queue can
contain up to eight unique channels in SE mode and up to
four unique channels in DIFF mode. The channels can be
non-consecutive, but must be listed in increasing order.
These devices support TTL-level input signals up to 50 kHz.
Analog Output
Trigger Input
When configured for output, these devices can pace A/D conversions on a second device.
The maximum analog output update rate for all devices depends
on several factors, including USB port speed.
The USB-1208FS-Plus and USB-1408FS-Plus each provide an
external digital trigger input that is software-selectable for rising
or falling edge, high or low level.
USB-1208LS
The USB-1208LS provides an external digital trigger input that
is software-selectable for high or low level.
This device offers two 10-bit analog outputs with a range of
0 V to 5 V.
Calibration
One analog output updates at a maximum rate of 100 S/s; two
analog outputs update at a maximum rate 50 S/s each. The
USB-1208LS updates in software-paced mode only.
All USB-1208FS-Plus/LS/1408FS-Plus Series devices are factorycalibrated. Specifications are guaranteed for one year. For calibration beyond one year, return the device to the factory for
recalibration.
USB-1208FS-Plus/1408FS-Plus
All devices offer two 12-bit analog outputs with a range of 0 V
to 5 V.
The USB-1208LS also supports field calibration with InstaCal.
Perform calibration whenever the ambient temperature changes
by more than ±10 °C from the last calibration.
When updating continuously from computer
memory (hardware-paced mode), the analog outputs update at
a maximum rate of 50 kS/s per channel.
OEM Versions (-Plus devices only)
The USB-1208FS-Plus-OEM and USB-1408FS-Plus-OEM have a
board-only form factor with header connectors for OEM and
embedded applications (no case, CD, or USB cable included).
All devices can be further customized to meet customer needs.
Concurrent AI/AO Scanning Operations
(-Plus devices only)
All USB-1208FS-Plus/1408FS-Plus devices support executing an
analog input scan and analog output scan at the same time.
Digital I/O
All devices provide 16 TTL-level digital I/O lines. Digital I/O can
be programmed on each 8-bit port (Port A and Port B) for either
input (default) or output.
On the USB-1208FS-Plus and USB-1408FS-Plus, port B0
through Port B7 are high-current drive (24 mA) digital I/O
connections.
The USB-1208FS-Plus-OEM and USB-1408FS-Plus-OEM have the
same specifications as the USB-1208FS-Plus/1408FS-Plus, but in
a board‑only form factor with header connectors instead of screw
terminals.
Measurement Computing
(508) 946-5100
2
[email protected]
mccdaq.com
USB-1208FS-Plus/LS/1408FS-Plus Series
Software
Software Support
The USB-1208FS-Plus/LS/1408FS-Plus Series is supported by the software in the table below.
Ready-to-Run Applications
DAQami™
InstaCal™
TracerDAQ™ and
TracerDAQ Pro
Data acquisition companion software with drag-and-drop interface that is used to acquire,
view, and log data, and generate signals. DAQami can be configured to log analog, digital, and
counter channels, and to view that data in real-time or post-acquisition on user-configurable
displays. Logged data can be exported for use in Excel® or MATLAB®. Windows OS
DAQami is included with the free MCC DAQ Software bundle (CD/download). Install DAQami
and try the fully-functional software for 30 days. After 30 days, all features except for data logging and data export will continue to be available – data logging and data export features can
be unlocked by purchasing the software.
An interactive installation, configuration, and test utility for MCC hardware. Windows OS
InstaCal is included with the free MCC DAQ Software bundle (CD/download).
Virtual strip chart, oscilloscope, function generator, and rate generator applications used to
generate, acquire, analyze, display, and export data. Supported features may vary by hardware.
The Pro version provides enhanced features. Windows OS
TracerDAQ is included with the free MCC DAQ Software bundle (CD/download).
TracerDAQ Pro is available as a purchased software download.
General-Purpose Programming Support
Universal Library™
(UL)
UL for Android™
(-Plus devices only)
Library for developing applications in C, C++, VB, C# .Net, VB .Net, and Python.
Windows OS
The UL is included with the free MCC DAQ Software bundle (CD/download).
Programming library of Java classes for programmers who develop apps for Android-based
tablets and phones. UL for Android communicates with select MCC DAQ devices. Supports
Android project development on Windows, Linux, Mac OS X
UL for Android is included with the free MCC DAQ Software bundle (CD/download).
Linux® driver
Open-source Linux drivers are available for most MCC devices. Example programs are also
provided.
Application-Specific Programming Support
ULx for
NI LabVIEW™
DASYLab®
MATLAB driver
®
A comprehensive library of VIs and example programs for NI LabVIEW that is used to develop
custom applications that interact with most MCC devices. Windows OS
ULx for NI LabVIEW is included with the free MCC DAQ Software bundle (CD/download).
Icon-based data acquisition, graphics, control, and analysis software that allows users to create
complex applications in minimal time without text-based programming. Windows OS
DASYLab is available as a purchased software download. An evaluation version is available for
28 days.
High-level language and interactive environment for numerical computation,
visualization, and programming. The Mathworks Data Acquisition Toolbox™ allows users to
acquire data from most MCC PCI and USB devices.
Visit www.MathWorks.com for more information about the Data Acquisition Toolbox.
Measurement Computing
(508) 946-5100
3
[email protected]
mccdaq.com
USB-1208FS-Plus/LS/1408FS-Plus Series
Specifications
Specifications
Analog Input Accuracy
USB-1208FS-Plus
All specifications are subject to change without notice.
Typical for 25°C unless otherwise specified.
Range
USB-1208FS-Plus and USB-1408FS-Plus
±20 V
5.1
±10 V
6.1
±5 V
8.1
±4 V
9.1
±2.5 V
12.1
±2 V
14.1
±1.25 V
20.1
±1 V
24.1
These specifications apply to both standard and OEM versions unless noted
otherwise.
Analog Input
A/D converter type: Successive approximation
Channels: 8 SE or 4 DIFF, programmable as SE or DIFF
Input common-mode voltage range for linear operation
SE Mode: CHx to GND, ±10 V max
DIFF Mode: CHx to GND, –10 V min, 20 V max
Absolute maximum input voltage: CHx to GND, ±28 V max
Input impedance: 122 kΩ
Input current
Input current is a function of applied voltage on the analog input channels. For
a given input voltage, Vin, the input leakage is approximately equal to (8.181
* Vin–12) µA
Vin = 10 V, 70 µA typ
Vin = 0 V, –12 µA typ
Vin = –10 V, –94 µA typ
Ranges: Software or selectable on a per-channel basis
SE mode: ±10 V
DIFF mode: ±20 V, ±10 V, ±5 V, ±4 V, ±2.5 V, ±2.0 V, ±1.25 V, ±1.0 V
Throughput
Maximum throughput scanning to computer memory depends on the
computer being used.
USB-1208FS-Plus
Software paced: 250 S/s typ, system‑dependent
Hardware paced: 50 kS/s
USB-1408FS-Plus
Software paced: 250 S/s typ, system‑dependent
Hardware paced: 48 kS/s
Channel gain queue: Up to 8 elements, software-selectable channel and range
Resolution
USB-1208FS-Plus
DIFF: 12 bits, no missing codes
SE: 11 bits (the AD7870 converter only returns 11-bits (0–2047 codes) in
SE mode)
USB-1408FS-Plus
DIFF: 14 bits, no missing codes
SE: 13 bits (the AD7871 converter only returns 13-bits (0–8192 codes) in
SE mode)
Integral linearity error
USB-1208FS-Plus: ±1 least significant bit (LSB) typ
USB-1408FS-Plus: ±2 LSB typ
Differential linearity error: ±0.5 LSB typ
Repeatability: ±1 LSB typ
Absolute accuracy long term drift (USB-1408FS-Plus only)
Extrapolating the long term drift accuracy specifications provides the approximate long term drift of the USB-1408FS-Plus intermediate input ranges.
±20 V range: ±3 LSB typ (Δt = 1000 hrs)
±4 V range: ±6 LSB typ (Δt = 1000 hrs)
±1 V range: ±8 LSB typ (Δt = 1000 hrs)
2.5VREF output current (USB-1408FS-Plus only)
Source: 5 mA max
Sink: 20 µA min, 100 µA typ
Trigger source (software-selectable)
External digital: TRIG_IN
Clock source (software-selectable)
Internal
External (SYNC), Rising Edge Triggered
Measurement Computing
(508) 946-5100
Accuracy (LSB)
Differential Mode
Single-Ended Mode
±10 V
4.0
Analog Input Accuracy
USB-1408FS-Plus
Range
Absolute Accuracy
25°C
Absolute Accuracy
0 to 50°C
±20 V
±10.98 mV
±49.08 mV
±10 V
±7.32 mV
±33.42 mV
±5 V
±3.66 mV
±20.76 mV
±4 V
±2.92 mV
±19.02 mV
±2.5 V
±1.83 mV
±14.97 mV
±2 V
±1.70 mV
±14.29 mV
±1.25 V
±1.21 mV
±12.18 mV
±1 V
±1.09 mV
±11.63 mV
±10.98 mV
±49.08 mV
Differential Mode
Single-Ended Mode
±10 V
4
[email protected]
mccdaq.com
USB-1208FS-Plus/LS/1408FS-Plus Series
Specifications
Digital I/O
Noise Performance
Digital type: CMOS
Number of I/O: 16 (Port A0 through A7, Port B0 through B7)
Configuration: 2 banks of 8 (port B is the high-current drive)
Pull-up/down configuration: All pins pulled up to 5 V via 47 kΩ resistors (default).
Change to pull-down using internal user-configurable jumpers.
Input high voltage: 2.0 V min, 5.5 V absolute max
Input low voltage: 0.8 V max, –0.5 V absolute min, 0 V recommended min
Output high voltage, port A: 4.4 V min (IOH = –20 µA), 3.84 V min
(IOH = –6.0 mA)
Output low voltage, port A: 0.1 V max (IOL = 20 µA), 0.33 V max
(IOL = 6.0 mA)
Output high voltage, port B: 4.4 V min (IOH = –50 µA), 3.76 V min
(IOH = –24.0 mA)
Output low voltage, port B: 0.1 V max (IOH = 50 µA), 0.44 V max
(IOH = 24.0 mA)
Power on and reset state: Input
USB-1208FS-Plus
Range
Typical Counts
Least Significant
BitRoot Mean Square
(LSBRMS)
±20 V
2
0.30
±10 V
2
0.30
±5 V
3
0.45
±4 V
3
0.45
±2.5 V
4
0.61
±2 V
5
0.76
±1.25 V
7
1.06
±1 V
8
1.21
2
0.30
Differential Mode
External Trigger
Trigger source: External digital, TRIG_IN
Trigger mode: Edge or level sensitive; software-selectable for CMOS compatible
rising or falling edge, high or low level.
Trigger latency: 10 µs max
Trigger pulse width: 1 µs min
Input type: Schmitt trigger, 47 kΩ pull-down to ground
Schmitt trigger hysteresis: 1.01 V typ, 0.6 V min, 1.5 V max
Input high voltage threshold: 2.43 V typ, 1.9 V min, 3.1 V max
Input high voltage limit: 5.5 V absolute max
Input low voltage threshold: 1.42 V typ, 1.0 V min, 2.0 V max
Input low voltage limit: –0.5 V absolute min, 0 V recommended min
Single-Ended Mode
±10 V
USB-1408FS-Plus
Range
Typical Counts
Least Significant
BitRoot Mean Square
(LSBRMS)
External Clock Input/Output
Pin name: SYNC
Pin type: Bidirectional
Direction (software-selectable)
Input (default): Receives A/D clock from external source. Active on rising edge.
Output: Outputs internal A/D clock. Active on rising edge.
Input clock rate
USB-1208FS-Plus: 50 kHz, max
USB-1408FS-Plus: 48 kHz, max
Clock pulse width
Input mode: 1 µs min
Output mode: 5 µs min
Input type: Schmitt trigger, 47 kΩ pull-down to ground
Schmitt trigger hysteresis: 1.01 V typ, 0.6 V min, 1.5 V max
Input high voltage threshold: 2.43 V typ, 1.9 V min, 3.1 V max
Input high voltage limit: 5.5 V absolute max
Input low voltage threshold: 1.42 V typ, 1.0 V min, 2.0 V max
Input low voltage limit: –0.5 V absolute min, 0 V recommended min
Output high voltage: 4.4 V min (IOH = –50 µA), 3.80 V min (IOH = –8 mA)
Output low voltage: 0.1 V max (IOL = 50 µA), 0.44 V max (IOL = 8 mA)
Differential Mode
±20 V
8
1.21
±10 V
8
1.21
±5 V
9
1.36
±4 V
10
1.51
±2.5 V
12
1.81
±2 V
14
2.12
±1.25 V
18
2.72
±1 V
22
3.33
8.0
1.21
Single-Ended Mode
±10 V
Counter
Analog Output
Pin name: CTR
Counter type: Event counter
Number of channels: 1
Input type: Schmitt trigger, 47 kΩ pull-down to ground
Input Source: CTR screw terminal
Resolution: 32 bits
Maximum input frequency: 1 MHz
High pulse width: 500 ns min
Low pulse width: 500 ns min
Schmidt trigger hysteresis: 1.01 V typ, 0.6 V min, 1.5 V max
Input high voltage threshold: 2.43 V typ, 1.9 V min, 3.1 V max
Input high voltage limit: 5.5 V absolute max
Input Low voltage threshold: 1.42 V typ, 1.0 V min, 2.0 V max
Input low voltage limit: –0.5 V absolute min, 0 V recommended min
Resolution: 12 bits, 1 in 4096
Output range: 0 V to 5 V
Number of channels: 2
Throughput
Software paced: 250 S/s single channel typ, system‑dependent
Hardware paced: 50 kS/s max per channel
Power on and reset voltage: 0 V, ±20 mV typ, initializes to 000h code
Output drive (each D/A out): 5 mA, sourcing
Slew Rate: 0.8 V/µs typ
Accuracy, all values are (±), 0 V to 5 V: 4.0 LSB typ, 45.0 LSB max (accuracy
tested at no load)
Analog output accuracy components, all values are (±)
Range: 0 V to 5 V
% of FSR: 0.1 typ, 0.9 max
Gain error at full scale: 4.0 mV typ, 36.0 mV max
Offset: 1.0 mV typ, 9.0 mV max
Zero-scale offsets may result in a fixed zero-scale error producing a dead-band
digital input code region. In this case, changes in digital input code of less than
0x040 may not produce a corresponding change in the output voltage. The
offset error is tested and specified at code 0x040.
Accuracy at FS: 4.0 mV typ, 45.0 mV max
Measurement Computing
(508) 946-5100
Non-Volatile Memory
EEPROM: 2,048 bytes (768 bytes calibration, 256 bytes user,1,024 bytes system data)
5
[email protected]
mccdaq.com
USB-1208FS-Plus/LS/1408FS-Plus Series
Specifications
Power*
CAL current
Source: 5 mA max
Sink: 20 µA min, 200 nA typ
Trigger source (software-selectable): External digital (TRIG_IN)
Supply Current
During USB enumeration: < 100 mA
After USB enumeration, including DIO, AO, SYNC, and +VO output loading: < 500 mA
+VO power available after USB enumeration: 4.5 V min, 5.25 V max
+VO output current after USB enumeration: 100 mA max
Analog Input Accuracy
Range
General
Accuracy (LSB)
Differential Mode
Device type: USB 2.0 full-speed mode (12 Mbps)
Device compatibility: USB 1.1, 2.0
Environment
Operating temperature: 0 ˚C to 70 ˚C
Storage temperature: –40 ˚C to 70 °C
Relative humidity: 0% to 90% non-condensing
Signal I/O connector
USB-1208FS-Plus, USB-1408FS-Plus: 2 banks of screw-terminal blocks
USB-1208FS-Plus-OEM, USB-1408FS-Plus-OEM: Two 20-pin, 0.1 in. pitch
headers
Mechanical
Dimensions (L × W × H)
USB-1208FS-Plus, USB-1408FS-Plus: 79 × 82 × 27 mm (3.20 × 3.10 × 1.05 in.)
USB-1208FS-Plus-OEM, USB-1408FS-Plus-OEM: 81.28 × 70.36 × 13.72 mm
(3.20 × 2.77 × 0.54 in.)
±20 V
5.1
±10 V
6.1
±5 V
8.1
±4 V
9.1
±2.5 V
12.1
±2 V
14.1
±1.25 V
20.1
±1 V
24.1
Single-Ended Mode
±10 V
USB-1208LS
4.0
Accuracy Components, All Values are (±)
Range
Analog Input
A/D converter type: Successive approximation
Channels: 8 SE or 4 DIFF, programmable as SE or DIFF
Input voltage range for linear operation, SE mode
CHx to GND: ±10 V max
Input common-mode voltage range for linear operation, differential mode,
DIFF mode
CHx to GND: –10 V min, 20 V max
Absolute maximum input voltage
CHx to GND: ±40 V max
Input current
Input current is a function of applied voltage on the analog input channels. For
a given input voltage, Vin, the input leakage is approximately equal to (8.181
* Vin–12) µA
Vin = 10 V, 70 µA typ
Vin = 0 V, –12 µA typ
Vin = –10 V, –94 µA typ
Input impedance: 122 kΩ
Ranges: Software or selectable on a per-channel basis
SE mode: ±10 V
DIFF mode: ±20 V, ±10 V, ±5 V, ±4 V, ±2.5 V, ±2.0 V, ±1.25 V, ±1.0 V
Throughput
Maximum throughput scanning to computer memory depends on the
computer being used.
Software paced: 50 S/s typ, system‑dependent
Hardware paced: 1.2 kS/s
BURSTIO to 4 kS FIFO: 8 kS/s
Channel gain queue: Up to 8 elements, software-selectable channel and range
Resolution
DIFF: 12 bits, no missing codes
SE: 11 bits (the AD7870 converter only returns 11-bits (0–2047 codes) in
SE mode)
CAL accuracy: CAL = 2.5 V, ±0.05% typ, ±0.25% max
Integral linearity error: ±1 least significant bit (LSB) typ
Differential linearity error: ±0.5 LSB typ
Repeatability: ±1 LSB typ
% of Reading
Gain Error at FS
(mV)
Offset
(mV)
Accuracy
at FS (mV)
Differential Mode
±20 V
0.2
40
9.766
49.766
±10 V
0.2
20
9.766
29.766
±20 V
0.2
40
9.766
49.766
±10 V
0.2
20
9.766
29.766
±5 V
0.2
10
9.766
19.766
±4 V
0.2
8
9.766
17.766
±2.5 V
0.2
5
9.766
14.766
±2 V
0.2
4
9.766
13.766
±1.25 V
0.2
2.5
9.766
12.266
±1 V
0.2
2
9.766
11.766
20
19.531
39.531
Single-Ended Mode
±10 V
0.2
Analog Output
D/A converter type: PWM
Resolution: 10 bits, 1 in 1024
Output range: 0 V to 5 V
Number of channels: 2
Throughput (software paced)
100 S/s single-channel mode
50 S/s dual-channel mode
Power on and reset voltage: Initializes to 000h code
Maximum voltage
Vs is the USB +5 V power. The maximum analog output voltage is equal to Vs
at no load. V is system-dependent and may be less than 5 V.
No load: Vs
1 mA load: 0.99 * Vs
5 mA load: 0.98 * Vs
Output drive (each D/A out): 30 mA
Slew rate: 0.14 V/ms typ
* Self-powered USB hubs and hosts have their own power supply. The USB
port(s) on your computer are root port hubs. All externally powered root
port hubs (desktop computers) provide up to 500 mA of current for a
USB device. Battery-powered root port hubs provide 100 mA or 500 mA,
depending upon the manufacturer. A laptop PC that is not connected to an
external power adapter is an example of a battery-powered root port hub.
Bus-powered USB hubs and hosts do not have their own power supply.
Measurement Computing
(508) 946-5100
6
[email protected]
mccdaq.com
USB-1208FS-Plus/LS/1408FS-Plus Series
Ordering
Digital I/O
Power*
Digital type: 82C55
Number of I/O: 16 (Port A0 through A7, Port B0 through B7)
Configuration: 2 banks of 8.
Pull-up/down configuration: All pins pulled up to Vs through 47 kΩ resistors
(default). Positions available for pull down to ground. Hardware-selectable
through 0 Ω resistors as a factory option.
Input high voltage: 2.0 V min, 5.5 V absolute max
Input low voltage: 0.8 V max, –0.5 V absolute min, 0 V recommended min
Output high voltage (IOH = –2.5 mA): 3.0 V min
Output low voltage (IOL = 2.5 mA): 0.4 V max
Supply current: 20 mA (total current requirement; includes up to 5 mA for
the status LED)
5 V USB power available
Connected to self-powered hub: 4.5 V min, 5.25 V max
Connected to bus-powered hub: 4.1 V min, 5.25 V max
Output current (total amount of current that can be sourced from the USB 5 V, analog
outputs and digital outputs)
Connected to self-powered hub: 450 ma min, 500 ma max
Connected to bus-powered hub: 50 mA min, 100 mA max
External Trigger
USB controller clock error
25 °C: ±30 ppm max
0 °C to 70 °C: ±50 ppm max
Device type: USB 1.1 low-speed mode (1.5 Mbps)
Device compatibility: USB 1.1, 2.0
General
Trigger source: External digital, TRIG_IN (protected with a 1.5 kΩ series resistor)
Trigger mode: Level sensitive; software-selectable for TTL level high or low input
Trigger latency: Burst, 25 µs min, 50 µs max
Trigger pulse width: Burst, 40 µs min
Input high voltage: 3.0 V min, 15.0 V absolute max
Input low voltage: 0.8 V max
Input leakage current: ±1.0 µA
Environment
Operating temperature: 0 ˚C to 70 ˚C
Storage temperature: –40 ˚C to 70 °C
Relative humidity: 0% to 90% non-condensing
Acquisition data buffer: 4 kS
Signal I/O connector: 2 banks of screw-terminal blocks
Dimensions (L × W × H): 79 × 82 × 27 mm (3.20 × 3.10 × 1.05 in.) Counter
Pin name: CTR
Counter type: Event counter
Number of channels: 1
Input type: TTL, rising edge triggered
Resolution: 32 bits
Maximum input frequency: 1 MHz
High pulse width: 500 ns min
Low pulse width: 500 ns min
Schmidt trigger hysteresis 20 mV to 100 mV
Input leakage current: ±1 µA
Input high voltage: 4.0 V min, 5.5 V absolute max
Input low voltage: 1.0 V max, –0.5 V absolute min
* Self-powered USB hubs and hosts have their own power supply. The USB
port(s) on your computer are root port hubs. All externally powered root
port hubs (desktop computers) provide up to 500 mA of current for a
USB device. Battery-powered root port hubs provide 100 mA or 500 mA,
depending upon the manufacturer. A laptop PC that is not connected to an
external power adapter is an example of a battery-powered root port hub.
Non-Volatile Memory
Memory size: 8192 bytes
Memory configuration
Address 0x0000 to 0x17FF: Read/write access, A/D data (4 kS)
Address 0x1800 to 0x1EFF: Read/write access, user data area
Address 0x1F00 to 0x1FEF: Read/write access, calibration data
Address 0x1FF0 to 0x1FFF: Read/write access, system data
Bus-powered USB hubs and hosts do not have their own power supply.
Order Information
Software also Available from MCC
Hardware
Part No.
Description
USB‑1208LS
USB-based data acquisition device with eight
12-bit analog inputs, 1.2 kS/s, two analog
outputs, and 16 digital I/O. Includes USB cable
and MCC DAQ software CD.
USB-1208FS-Plus
USB-based multifunction DAQ device with 8 SE/
4 DIFF analog inputs, up to 12-bit resolution,
50 kS/s, 2 analog outputs, and 16 digital I/O
(includes eight high-current lines). Includes USB
cable and MCC DAQ software CD.
USB-1208FS-Plus-OEM
Board-only USB-based DAQ device with eight
analog inputs, 50 kS/s, up to 12-bit resolution,
50 kS/s, two analog outputs, 16 digital I/O lines
(includes eight high-current lines).
USB‑1408FS-Plus
USB-based multifunction DAQ device with 8 SE/
4 DIFF analog inputs, up to 14-bit resolution,
48 kS/s, 2 analog outputs, and 16 digital I/O
(includes eight high-current lines). Includes USB
cable and MCC DAQ software CD.
USB-1408FS-Plus-OEM
Board-only USB-based multifunction DAQ board
with 8 SE/4 DIFF analog inputs, up to 14-bit
resolution, 48 kS/s, 2 analog outputs, and 16
digital I/O (includes eight high-current lines).
Measurement Computing
DS-USB-1208FS-Plus-LS-1408FS-Plus-Series
(508) 946-5100
7
DAQami
Data acquisition companion software for acquiring
data and generating signals
TracerDAQ Pro
Out-of-the-box virtual instrument suite with strip
chart, oscilloscope, function generator, and rate
generator – professional version
DASYLab
Icon-based data acquisition, graphics, control, and
analysis software
[email protected]
mccdaq.com
May 2017. Rev 2
© Measurement Computing Corporation
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement