View - Liberty AV Solutions

View - Liberty AV Solutions
NEW TECHNOLOGY
GUIDE
VALUE-ENGINEERED DIGITAL SOLUTIONS
NEW TECHNOLOGY GUIDE CONTENTS
HDMI ADAPTER RING
DL-AR Customizable HDMI Adapter Ring
3
IPLINX AV OVER IP
26
DL-A51 HDMI 5x1 Matrix Switcher
26
DISTRIBUTION AMPLIFIERS / SPLITTERS
IPLINX 5000 SERIES 4k AV Over IP Solution
5
DL-DA12S / DL-DA14S HDMI Distribution Amps
IPLINX 2000 SEREIES 1080p AV Over IP Solution
5
MATRIX SWITCHERS
EDUCATION SYSTEMS & SOLUTIONS
EDU-KIT-001 / EDU-KIT-1H1V
Multi-Function AV Distribution System
6
DL-1H1V1U-WP-W HDMI/VGA/USB HDBT 2.0 WP White
7
DL-HD2WP-RX HDBT 2.0 RX w/USB Hub
7
COLLABORATION & PRESENTATION SWITCHERS
DL-SC51TR BYOC System
8
DL-SE3H1V-C Auto Switcher / HDBT Extender
9
INT-HD52 5x1+1 Auto Switching/Scaling
10
AAP-2011-BYMG Arrive Airpoint 2.0 Wireless Media Gateway
11
AHP-4010-CMMH Arrive Huddlepoint
11
DTEN55NDE
Interactive Panel for Collaboration & Presentation
12
DL-UHDILC In-Line Hdmi Auto Sensing Room Controller
13
27
DL-HDM44-SS / DL-HDM66-SS / DL-HDM88-SS
Standard Matrix Switchers
28
DL-HDM44-FS / DL-HDM88-FS Fast Matrix Switchers
29
INT-44HDX / INT-66HDX / INT-88HDX
HDBaseT HDCP 2.2 Matrix Switchers
30
INT-HD70-RX / INT-HDX100-RX / DIGI-BSR-4K
Matrix Switchers
30
AUDIO AMPLIFICATION
AUD-220 2 Input Audio Amplifier
31
AUD-340 3 Input Audio Amplifier
31
ROOM CONTROL
LB-ICP Control Processor
32
LB-KP8 / LB-KP8E Keypad and Wallplate
32
DL-UHDILC In-Line HDMI Auto Sensing Room Controller
33
ADDITIONAL EXTENDERS / CONVERTERS
HDBASET EXTENDERS
14
DL-HDCP-C HDCP 2.2 to 1.4 Converter
33
DL-DP100 HDBaseT Displayport 4K
14
DL-SP HDMI Surge Protector
33
DL-UHDRC70 HDBaseT TX/RX Set
15
USB 3.0 EXTENSION
DL-HD70LS Slim HDMI Over Twisted Pair 70m
15
DL-USB3.0 Active Extension Cable
34
DIGI-HD60-WP-S HDBaseT Wall Plate Extender
16
DIGI-FO-USB3.0 Fiber Extender System
35
INT-HDX100-TX / INT-HDX100-RX HDBaseT 100m Extenders
17
USB 2.0 EXTENSION
INT-HD70-TX / INT-HD70-RX HDBaseT 70m Extenders
17
DIGI-HDUSB HDMI and USB 2.0 Extension System
42
RACK12 EXT / PSU12 Extender Accessories
17
DIGI-USB2-4P USB 2.0 4-Port Extension System
43
DL-HD2100 HDMI HDBaseT 18g 4k60 4:4:4
18
TECHNOLOGY ALLIANCE PARTNERS
DIGI-BSR-4K HDBaseT 100m Scaling Receiver
18
NIVEO
36-38
DL-HDE100 Slim HDBaseT 100m Extender
19
SP CONTROLS
39-40
DL-HD70 Slim HDBaseT 70m Extender
19
ACCESSORIES
DL-HDRKKT HDBaseT Extender Accessories
19
FLEXBOX-WH AV Enclosure Box
41
BYOD-PUCK AV Connection Hub
42
TRB-2V1AD / TSPB-2V1AD / TDPB-2V1AD Table Top AV Boxes
43
DL-HD60-ARC HDBaseT Extender with Audio Return Channel
ADDITIONAL EXTENDERS / CONVERTERS
DL-HD50 HDMI Over Single CAT 50m
20
AUTO SWITCHERS AND EXTENDERS
2
DL-A31 HDMI 3x1 Matrix Switcher
HDMI CABLES
DL-AS21C 2x1 HDMI VGA Auto Switcher
21
HDPMM HDMI Premium 18G Cable
DL-S41 4x1 Slim HDMI Auto Switcher
21
HDMI Cable Solutions
INT-HD52 5X1+1 Auto Switching/Scaling Presentation Switch
22
DL-HDM-M HDMI Premium 18G Active Optical Cable
47
DL-AS61 6x1 HDMI VGA Auto Switcher
22
PF-HDM-M HDMI Premium 18G Active Optical Plenum Cable
47
DL-AS31-2H1V 3x1 HDMI VGA Auto Switcher
23
FIBER OPTIC CABLE
DL-AS31-2H1DP 3x1 HDMI DisplayPort Auto Switcher
23
STRONGER, SAFER, FASTER (SSF) FIBER SOLUTIONS
48-51
DL-AS31-1H1DP1V 3x1 HDMI VGA DisplayPort Auto Switcher
23
STANDARD FIBER SOLUTIONS
52-54
AS-2H Dual HDMI Auto Switcher
24
PRODUCT HIGHLIGHTS
AS-1H1V HDMI VGA Auto Switcher
24
CATEGORY CABLE SOLUTIONS
AS-1H1DP HDMI Displayport Auto Switcher
24
RF COAXIAL SOLUTIONS
AS-2H-WP Dual HDMI Auto Switcher Wallplate
25
SERIAL DIGITAL SOLUTIONS
60
AS-1H1V-WP HDMI VGA Auto Switcher Wallplate
25
SPEAKER CABLE SOLUTIONS
61-63
AS-1H1DP-WP HDMI Displayport Auto Switcher Wallplate
25
800.530.8998
|
www.LibAV.com
|
SPECIFICATIONS SUBJECT TO CHANGE
44
45-46
55-57
59
|
IMAGES NOT TO SCALE
HDMI ADAPTER RING
VALUE-ENGINEERED DIGITAL SOLUTIONS
HDMI ADAPTER RING DL-AR
DL-AR
UNIVERSAL HDMI ADAPTER RING COMPLETE ASSEMBLY
The DL-CL black clamp is included with
the DL-AR complete assembly and also
sold separately.
ADVANCED
NEW DESIGN!
Specialized security screws for locking the
HDMI cable* to the ring are included.
Two sizes of foam inserts are included to
fit any sized cable jacket.
• Slimmer, sleeker new design
• Two-position eyelets
• Dongle & adapter versions available
• Increased adapter options
• Get a personalized tag!
Liberty's new and improved
HDMI Adapter Ring boasts
sleeker adapter sizes with
gold-plated connectors to
ensure reliable connectivity
and more compactness for
tighter spaces.
The patent-pending stainless
steel ring & clamp locks in
the HDMI cable going to
the display while all of the
adapters are at your fingertips.
The adapters are guaranteed
to stay locked to the HDMI
cable so they won't get lost
for the next presentation!
Boardrooms, lecture halls,
meeting rooms, classrooms and
other mixed use venues should
never be without it. Make
Liberty's breakthrough DL-AR
Adapter Ring part of every
installation and feel the love
from your customers!
Two-position eyelets
for more versatility!
*HDMI cable not included,
see back page for options or
go to www.LibAV.com for
Liberty's entire line of HDMI
cable solutions!
Create your own
CUSTOMIZED
ARDPHD
Display Port male
to HDMI female
in-line adapter
HDMI Adapter Ring
Check out our simple & free online
configurator at www.LibAV.com!
ARDVHD
DVI-D single link male
to HDMI A female
Choose any adapter, clamp, cable,
or tool that is available
Add To Cart
DL-AR826
Login
for
Price
ARMDHD
See a preview of your custom ring before you buy!
Mini-HDMI C male to
HDMI female in-Line
adapter
Easily add your customized HDMI Ring
to cart with any quantity
ARMCHD
Micro-HDMI D male
to HDMI female
in-line adapter
Get instant pricing when logged in
ARMDPHD
Your unique part number is automatically
generated, re-ordering is super simple!
Mini-Display Port
male to HDMI female
in-line adapter
See complete list of your selected items
DL-CL
DL-AP
BLACK clamp
assembly &
foam inserts
to securely
fit any sized
HDMI cable
Lightning digital
AV adapter
|
IMAGES NOT TO SCALE
MD098ZM /A
30-pin digital
AV adapter
*Apple adapters sold separately
800.530.8998
2
SPECIFICATIONS SUBJECT TO CHANGE
MD826ZM/A
Add Apple®
adapters with
our custom
white clamp!*
Fits any dongle
or cable
|
| www.LibAV.com |
800.530.8998
|
SPECIFICATIONS SUBJECT TO CHANGE
www.LibAV.com
|
IMAGES NOT TO SCALE
3
IPLINX AV OVER IP
Check out our simple to use, super affordable AV
over IP System - IPLinx! Watch the game on your
video wall, see 4k distributed video, and experience
the simplicity and quality IPLinx has to offer!
Easy Drag & Drop App easily
moves video to desired displays
IPLinx iOS/PC Control/Preview App
Provides complete matrix
or video wall control
• Designed to Offer Simple System Control
• Drag and Drop Video Selection
•P
ower On/Off Displays with CEC Control
•C
reates and Stores up to Three
System Presets
4
800.530.8998
|
www.LibAV.com
|
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
IPLINX AV OVER IP
Distribute A/V, USB and control signals over a 1Gb network. Great for digital signage, house of
worship, combined conference rooms and bars and restaurants. Easy to install and configure
all while remaining very affordable.
IPLinx 5000 Series – 4K AV Over IP Solution
• JPEG2000
• 4K/HDR Compatible
• PoE
• Low Latency
• Video Wall Capable up to 16x16
• Supports TCP/IP, RS232, IR Control
IPLinx IPEX5001 4K Encoder
• USB Extension
IPLinx IPEXCB
Control Interface
• Audio, Video and USB can be
Routed Independently
• Each Decoder Equipped with
a 4k Up/Down Scaler
• Ready made Crestron, Control4,
RTI and Savant Drivers Available
IPLinx IPEX5002 4K Decoder
IPLinx 2000 Series – 1080p AV Over IP Solution
• H.264
• Supports up to 1080p
• PoE
• Video Wall Capable up to 16x16
• Supports TCP/IP, RS232,
IR Control
IPLinx IPEX2001 1080p Encoder
• Supports CBR/VBR
IPLinx IPEXCB
Control Interface
IPLinx IPEX2002 1080p Decoder
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
|
800.530.8998
|
www.LibAV.com
• Each Decoder Equipped with a
1080p Scaler
• Ready Made Crestron, Control4,
RTI Drivers Available
5
EDUCATION SYSTEMS & SOLUTIONS
VALUE-ENGINEERED DIGITAL SOLUTIONS
EDU-KIT-001 / EDU-KIT-1H1V
MULTI-FUNCTION AV DISTRIBUTION SYSTEM
INCLUDED IN PACKAGE:
• Q ty 1: TPHD541T-WP HDMI HDBaseT auto or manual switching wall plate
• Q ty 1: TPHD541R-PA AV receiver/processor with HDBaseT
• Q ty 1: WP4N Manual control wall plate
PACKAGE FEATURES AND BENEFITS:
• Double-gang wall plate with 2 HDMI inputs, USB-B connection, & source selection
button. Signal extended via HDBaseT 2.0
• A uto-sensing/switching or manual switching of HDMI inputs. Extend HDMI & USB 2.0
for Smart Board control (or any other peripheral device) all over a single Cat6 cable
up to 30 meters
• S ingle-gang control plate offers HDMI source selection, audio source selection,
audio volume control, and system power on or off, as well as IR sensor for IR learning.
USB-A port provided to copy your configuration for easy mass deployment
• S ingle Cat6 connection from Control plate to AV plate, and from AV plate to receiver/
processor. Control and AV plate remotely powered via PoC
• S ave IR or RS232 display power commands. Single button press to power on/off
entire system
OPTIONAL ADDITIONS
TO THIS ROOM
1) If VGA with audio is needed,
add the DL-VHD to convert
VGA w/audio to HDMI at the
teacher station and use one of
the HDMI inputs
2) N
iveo wireless access point
NWA100 ceiling mount or
NWA200 in-wall solution
3) Length of cables to be
determined and can be
included with
the package
urge protection from Niveo
4) S
•W
eb base user GUI allows user to fully control system from PC or tablet
5) Atlas Sound Speakers
• 2 0 watt 4 ohm integrated audio amplifier as well as mic/line level audio input
• A larm/PA mute trigger
• P ackage with appropriate length wire & cable, speakers, power products,
and any other Liberty provided products to create a complete kit with a
single part number
6
800.530.8998
|
www.LibAV.com
|
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
EDUCATION SYSTEMS & SOLUTIONS
VALUE-ENGINEERED DIGITAL SOLUTIONS
DL-1H1V1U-WP-W
HDMI/VGA/USB HDBT 2.0 WP WHITE
The DigitaLinx DL-1H1V1U-WP-W is a 2x1 auto switching
HDBT 2.0 transmitter that supports the long distance
transport of HDMI, VGA and USB 2.0 up to 70 meters / 230'
using CAT6 cabling and features an HDMI, VGA with Audio
and USB(A) input. The DL-1H1V1U-WP-W gives you the
ability to automate the display technology on whenever a
video signal is introduced to the system on either the HDMI
or VGA input. It will also turn the display technology off
after a specified amount of time has passed when no video
signal is present. It also gives you the ability to turn on/
off display as well and switch from one input to another
manually from the face plate.
key features
• Extends HDMI / VGA and USB up to 100m / 330’
• RS232 pass through over HDBaseT
• Supports [email protected] 4:2:0
• Front Panel Input and Display on/off Selection
• Compatible with the DL-HD2WP-RX receiver
DL-HD2WP-RX VALUE-ENGINEERED DIGITAL SOLUTIONS
HDBT 2.0 RX W/USB HUB
The DigitaLinx DL-HD2WP-RX is an HDBT 2.0 receiver that
is compatible with the DL-1H1V1U-WP-W 2x1 auto switching
wall plate that transmits HDMI, VGA and USB 2.0 up to 70
meters / 230'. There is an RS232 port for connecting displays
for on/off automation, HDMI out and de-embed 3.5mm
audio output as well as a 4 port USB hub that features four
USB (A) ports. When paired with the DL-1H1V1U-WP-W, the
extenders system is ideal for situations where USB must be
extended with HDMI or VGA for interactivity for items such
as whiteboards for conference rooms or classrooms.
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
|
800.530.8998
key features
• Matching HDBaseT2.0 RX with USB Hub
• Offers PoE to power the TX plate
• Pass-Through RS232
|
www.LibAV.com
7
COLLABORATION & PRESENTATION SWITCHERS
VALUE-ENGINEERED DIGITAL SOLUTIONS
AUTOMATED CONFERENCE/
HUDDLE SPACE SOLUTIONS
Huddle rooms, conference rooms, BYOD,
auto-switching, the list goes on… And we all
understand how important these spaces are
to our customers. Functional, affordable, and
most importantly EASY TO USE huddle spaces.
Liberty AV Solutions huddle/conference space
systems and products will fit your needs and
budget. Our systems integrate wireless BYOD,
room scheduling, soft codec integration, simple
automation control, switching, extension, and
more. Remember the Liberty turn key huddle
systems for your next project!
DISPLAY
Laptop
USB MIC
HDMI
CATEGORY
USB
RS232
WIRELESS
BYOD
USB CAM
Input on RX allows you to
incorporate wireless gateways
to wirelessly screen share!
System automation built in! It
automatically powers up TV
or projector via RS232, up/
down relays for projector
screens with no need for
separate system control.
Single Cable from Table to Display
up to 70m / 230’
Connect HDMI, DP, VGA
and USB Devices at Table
Connect Display, BYOD and
and USB Devices at Display Location
DL-SC51TR
Users bring their own computer to the room
eliminating the need for dedicated conference
systems- the computer is the conference system!
Users can now utilize the rooms built in USB mic
and camera for a professional user experience.
• 5x1 A/V auto switcher, HDBaseT 2.0 extender
and simple control system in one
• 4 Port USB 2.0 hub built in
• Local HDMI input on RX for BYOD devices
• Automated control features two relay ports
and an RS232 port to power up displays and
room peripherals when video input is detected
• Supports TCP/IP and RS232 control
DigitaLinx DL-SC51TR BYOC System
8
800.530.8998
|
www.LibAV.com
|
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
COLLABORATION & PRESENTATION SWITCHERS
VALUE-ENGINEERED DIGITAL SOLUTIONS
Collaboration spaces
are growing at a rapid
rate. These are simple,
easy to use rooms for
people to screen share
and share ideas. Liberty’s
automated room solutions
will help simplify systems
configuration.
Projection Screen
Laptop
HDMI
CATEGORY
RS232
RELAY
Tablet
Projector
WIRELESS
BYOD
Two HDMI ports and one
VGA port at the table
plus one HDMI port at
the display allows for
seamless and easy to
use collaboration.
Automation built in!
Display powers on when
a video source is plugged
in, powers off after no
present video signal.
Single Cable from Table to Display
up to 70m / 230’
Connect HDMI, VGA
Devices at Table
DL-SE3H1V-C
DigitaLinx
DL-SE3H1V-C
Auto Switcher /
HDBT Extender
with Built in
Automation
Control!
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
|
Connect projector, BYOD Device
and Projector Screenat Display Location
Connect, automate and share. The DL-SE3H1V-C is a
complete 4K auto switcher and HDBaseT extender system
with built in automation control that powers up display
and room peripherals when video input is detected.
• 4x1 A/V Auto Switcher, HDBaseT Extender and
Simple Control System in one
• Local HDMI Input on RX for BYOD Devices
• Automated Control Features two Relay Ports
and an RS232 Port to Power up Displays and Room
Peripherals when Video Input is Detected
• Supports TCP/IP and RS232 Control
800.530.8998
|
www.LibAV.com
9
COLLABORATION AND PRESENTATION SWITCHERS
INT-HD52
5X1+1 AUTO SWITCHING/SCALING PRESENTATION SWITCH WITH HDBASET W/POE & HDMI OUTPUT
The Intelix INT-HD52 is a compact auto
switcher scalar that allows the integration
of analog and digital devices into a highdefinition environment. Mounting options
include under table or resting on a shelf. The
INT-HD52 allows selection of five different
A/V sources, and will simultaneously scale
the selected video to HDMI and HDBaseT
outputs. The unit features three HDCP
compliant HDMI inputs, one Display Port
input and one VGA input. The VGA input can
be configured to support YPbPr (component
video), YC (S-video), and C (composite
video) video formats with the appropriate
VGA breakout cable. There are eight fixed
output resolutions to choose from, and
several aspect ratio modes, which will
ensure your content is displayed properly.
The HDBaseT output will allow you to
extend audio, video, and control signals up
to 70m away.
REMOTE
MIC
CONTROL SYSTEM
AUDIO AMPLIFIER
key features
• 3 HDMI, 1 DP w/audio, 1 VGA w/audio input
• HDBaseT with PoE and a mirrored HDMI output
• Integrated scaling up to 1900X1200
• M ic / Line level audio input with audio embedding and
HDMI
HDBT
DP
VGA
AUDIO
IR
RS232
TCP/IP
WIRED
BYOD
DVD
phantom power
• A udio De-embedding w/balanced audio out
• Fast/seamless switching time <1s
• R S232 & IR tunneling over HDBaseT for control of
WIRELESS
BYOD
LAPTOP
INT-HD70-RX
HDBT RECIEVER
(Not Included)
connected devices/displays
• Controlable via RS232, TCP/IP, IR, or Front Panel
• A uto switching
• Ships with under table mounting ears
• Integrated web GUI for setup and/or control
• U p to 70m signal extension with PoE via HDBaseT
LEGACY
COMPUTER
PROJECTOR
DISPLAY
10
800.530.8998
|
www.LibAV.com
|
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
COLLABORATION AND PRESENTATION SWITCHERS
AAP-2011-BYMG
AAP-2011-BYMG
AirPoint 2.0 Media Collaboration Gateway with Wireless BYOD
ARRIVE® AIRPOINT™ 2.0 WIRELESS MEDIA GATEWAY
key features
• Supports Airplay, Miracast
and Intel WiDi
• U sers can select from
2.4Ghz or 5Ghz
• Connect to a LAN and use
the networks WAP resources,
automatically disengages l
ocal WiFi.
• W hen connected to LAN
the Airpoint can be managed
remotely.
AIRPOINT 2.0 WIRELESS MEDIA
COLLABORATION GATEWAY
AHP-4010-CMMH
AHP-4010-CMMH
HUDDLEPOINT
BYOC Ready; Cable, Power and
™
ARRIVE
HUDDLEPOINT
“BRING
OWN
CONFERENCING" TABLE CUBBY A/V SWITCHER
Presenting
Arrive
AirPoint™Media
2011-BYMG
- a YOUR
dual band,
Management
Hubuniversal wireless media collaboration gateway that supports Apple AirPlay ,
WiFi Miracast™, Intel™ WiDi, and playback from a USB flash drive. The AAP-2011-BYMG is a small but powerful wireless device embedded
withkey
the Arrive
AirPoint 2.0 software that provides wireless screen mirroring for BYOD presentations. It does not require any downloads
features
of applications or programs; or of dongles and other peripherals to be connected to the user’s WiFi capable presentation device. With
Table cubby and A/V auto switcher / scaler all in one!
an on-screen
graphic user interface that guides you through the connection steps for various devices, the AirPoint 2011 is a walk up,
2 HDMI
, 1 Display
Port
and 1 -VGA/A
and USB
through
connect
and use
capable
device
a big idea
withfeed
a very
smallinputs
footprint !
•
•
• B uilt in USB 3.0 Hub for connecting USB mics and cameras
All these capabilities are packaged in one user-friendly appliance interface that is easy on the pocket and easy on the eyes. This single
B
outlets for charging portable devices
uilt in DCdelivers
AIO •appliance
a powerful and efficient in-room wireless collaboration experience for huddle rooms, small meeting rooms,
flush-mounted
a conference table
• C an beand
classrooms
hotel guestonto
rooms.
C
able management built in
•
The Arrive AirPoint marks the industry’s first generation of universally integrated devices - supporting the most commonly used wireless
™
video connectivity platforms in a single device. This positions Arrive AirPoint™ as the most innovative and cost effective wireless video
interface in the market today.
Universal Wireless BYOD capable:

™
ALLIANCE
AAP-2011-001
THE HUDDLE
ROOM
SYSTEM FOR
ALL-YOU-NEED
|
| 800.530.8998
| www.LibAV.com
MEDIA & VIDEO COLLABORATION
SPECIFICATIONS SUBJECT TO CHANGE
IMAGES NOT TO SCALE
11
COLLABORATION AND PRESENTATION SWITCHERS
DTEN55NDE
DISPLAYTEN 55" 1080P INTERACTIVE PANEL FOR COLLABORATION AND PRESENTATION
DisplayTen designs turn key solutions to simplify collaboration for the next generation workplaces.DisplayTen’s
cable-free collaboration solution allows users to share content on the 55”, 70” and 84” interactive displays wirelessly.
It also features a pen and eraser with zero latency, 10-touchpoint integration, two way control between DisplayTen
and your Mac and PC as well as an elegant modular design.
KEY FEATURES
• DTEN Dongle wireless connection
HIGHLIGHTS
• No Wi-Fi set up and no software installation
• Share any content from your PC, Mac,
mobile or web on a HD display
•D
TEN Dongle offers two-way control
between DTEN and your device
• Annotate, organize and distribute
to anyone
• Usable without a separate computer or device
• Work with a ‘real’ pen and eraser
• Stable and customized with DTEN Android software
• Power cable is the only cable required
• Dedicated Wi-Fi connection for DTEN dongle
• Use the two-way control to
communicate ideas.
• Annotate with two-finger gesture
• 10 Touch Recognition
• Use one-click wireless
sharing to focus on ideas
and discussions
• Samsung Grade A 1080P glass
•P
orts for VGA, HDMI, RS232 and all
necessary connections you need
• Use dedicated Wi-Fi to
ensure data security
• Optional slot for PC module
• Virtually zero parallax
• Supports doc., ppt., jpg., mp4., and other file formats
• Available in both offline
and online modes
12
• Built-in web browser
800.530.8998
|
www.LibAV.com
|
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
COLLABORATION AND PRESENTATION SWITCHERS
DL-UHDILC IN-LINE HDMI AUTO SENSING ROOM CONTROLLER
The DigitaLinx DL-UHDILC is an HDMI in-line controller
that can automate room peripherals and sink devices
when a video signal is introduced to the unit. The
DL-UHDILC is 4K compatible, supports HDCP version 2.2,
has an analog and digital de-embedded audio output
and has 15 built in EDID presets that can be adjusted by
the rotary dial on the front panel.
When the DL-UHDILC auto-detects an input video
signal, the DL-UHDILC will automatically turn a display
or projector on either by CEC or by pre-loaded RS232
serial commands. The DL-UHDILC will trigger the first
relay port to switch a projector screen or window shade
down. When a video signal is no longer present after a
specified amount of time, the DL-UHDILC will turn off
the display or projector by either CEC or pre-loaded
RS232 commands and will trigger the second relay port
to switch a projector screen or window shade up.
LAPTOP
AUDIO AMPLIFIER
HDMI
RELAY
AUDIO
RS232
key features
• Stand alone unit
• Automates room peripherals when video signal is introduced to system
• Passes HDMI signals up to 18G 4K60 4:4:4
• Built in CEC controller from HDMI out.
• Built in RS232 controller to control display device
• B uilt in RELAY control for room peripherals such as projector
FRONT
BACK
screen or window shade
• De-embeds audio to coax S/PDIF or Stereo
• Switch for EDID Management with 15 EDID presets
PROJECTION SCREEN
PROJECTOR
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
|
800.530.8998
|
www.LibAV.com
13
HDBASET EXTENDERS
VALUE-ENGINEERED DIGITAL SOLUTIONS
DL-HD2100 HDMI HDBASET 18G 4K60 4:4:4 CAPABLE EXTENDER SET WITH IR,RS232,ARC, & AUDIO DE-EMBEDDING
The DigitaLinx DL-HD2100 is an 18G HDMI
2.0 extender over category cable that
can transport data rates up to 18Gbps up
to 100 meters. The system uses 2:1 data
compression when the signal surpasses
10Gbps, anything under 10Gbps will never be
compressed. In addition to extending high
bandwidth signals, the extension system will
extend IR, RS232, digital audio and is ARC
compatible. System supports flexible power
so entire extender circuit can be powered by
either the TX or RX side.
4K60 4:4:4 over HDBaseT
key features
18G 4K60 4:4:4
• 18G 4K60 4:4:4 capable HDBaseT complete extender set
• Extend HDMI, IR, RS232, ARC
• SPDIF connection for ARC or Digital audio extension
• Analog Audio De-embeding
• Flexible PoE power can be applied at either end
• Threaded power supply included
DL-DP100
VALUE-ENGINEERED DIGITAL SOLUTIONS
HDBASET DISPLAYPORT 4K, USB, RS232 AND IR EXTENDER COMPLETE SET
The DigitaLinx DL-HD2100 is an 18G
HDMI 2.0 extender over category cable
that can transport data rates up to
18Gbps up to 100 meters. The system
uses 2:1 data compression when the
signal surpasses 10Gbps, anything under
10Gbps will never be compressed. In
addition to extending high bandwidth
signals, the extension system will extend
IR, RS232, digital audio and is ARC
compatible. System supports flexible
power so entire extender circuit can be
powered by either the TX or RX side.
key features
• DisplayPort extension up to 330 feet via HDBaseT
• 4K, HDCP compliant
• Built-in USB2.0 extension
• Bi-directional RS232 and IR extension
• Powered at transmitter only
• Slim design
14
800.530.8998
|
www.LibAV.com
|
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
HDBASET EXTENDERS
VALUE-ENGINEERED DIGITAL SOLUTIONS
DL-UHDRC70 DIGITALINX HDBASET TX/RX SET WITH RECLOCKING FEATURE FOR CABLE BOX AND MEDIA PLAYER COMPATIBILITY
The DigitaLinx DL-UHDRC70 is an re-clocking HDBT
extender system that is compatible with source devices
that does not support clock stretching such as older cable
set top boxes. The DL-UHDRC70 can extend HDMI up to
70m / 230' and also extends bi-directional IR as well as
RS232. Supports 7.1 DTS Master HD and Dolby True HD.
key features
• R e-clocking feature allows for compatibility with Amazon Box, Roku Box,
Cable Boxes
• Cat5E/6 Cable 1080P 60M, 4K60 4:2:0 35M
• Cat6/7 Cable 1080P 70M, 4K604:2:0 40M
• 5-Play HDBT, bi-directional can be applied to either end
• Supports 7.1 DTS Master HD and Dolby True HD
• Locking Power Supply Connector
• LED indicators for power, HDCP, and HDBaseT link
• Powered at transmitter only
• Slim design
DL-HD70LS
SLIM HDMI OVER TWISTED PAIR 70M HDBASET COMPLETE SET WITH POWER AND IR EXTENSION
VALUE-ENGINEERED DIGITAL SOLUTIONS
The DigitaLinx DL-HD70LS extender set
transmits HDMI (1080p, 4Kx2K (UHD) & 3D),
including HDCP 2.2, and bidirectional IR up
to 70 meters away using a single solid core,
shielded Category 5e twisted pair cable. Builtin surge protection helps ensure hassle-free
and robust installations. The 12 volt power
supply is secured with a screw-on connector
to prevent the power from being accidentally
disconnected. The DL-HD70LS is sold only as a
set. The individual transmitter and receiver are
not compatible with other HDBaseT devices
due to proprietary PoE circuitry.
TRANSMITTER
key features
• HDMI transmission up to 230 feet (70m)
• Complete set Includes TX, RX, Power Supply,
and IR flasher/emitter
• 1080p, 4Kx2K & 3D compatible; CEC supported
• Built-in surge protection; diagnostic LEDs
• HDCP 2.2 compliant
• Bidirectional Wideband IR
• Power from TX supplies RX
• Locking power connector (power supply included)
RECEIVER
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
|
800.530.8998
|
www.LibAV.com
15
HDBASET EXTENDERS
DIGI-HD60-WP-S
60M HDMI WALL PLATE HDBASET TRANSMITTER
TECH SPECS
INPUT/OUTPUT CONNECTIONS
HDMI
One (1) HDMI Type A Receptacle
Twisted Pair
One (1) 8P8C port (Shielded RJ45)
SUPPORTED AUDIO AND VIDEO
Maximum Video
Compatibility at 60 m
Deep Color 36/30/24 Bit at 1080p
Maximum Video
Compatibility at 35 m
Deep Color 48 Bit at 1080p, 3D, and 4k x 2k (UHD)
up to 30 Hz: RGB, YCbCr 4:4:4, YCbCr 4:2:2; up to 60
Hz: YCbCr 4:2:0
Video Compliance
HDMI, HDCP 2.2, and CEC (Consumer Electronics
Control)
Embedded Audio
Up to PCM 8 channel, Dolby Digital TrueHD, and
DTS-HD Master Audio
HDBaseT SIGNAL CHARACTERISTICS
The Intelix DIGI-HD60-WP-S extends HDMI over a single
twisted pair cable by incorporating HDBaseT technology.
The DIGI-HD60-WP-S supports HDCP Encrypted
Content & DDC/EDID Transmission. DIGI-HD60-WP-S
transmits Ultra HD (4K2K), HDTV Video Resolutions up to
720p/1080i/[email protected] and WUXGA (1920X1200 @60Hz) at
distances of 60m (196ft). Diagnostic LED ensure hassle-free
and robust installations. The DIGI-HD60 series extenders are
compatible with all Intelix HDBaseT product offerings and
any product that meets the HDBaseT specifications.
Maximum Distance
60 m
Cable Requirements
Solid core shielded Category 5e, Category 6 or
greater with TIA/EIA-568B crimp pattern
Bandwidth
10.2 Gbps
CHASSIS & ENVIRONMENTAL
Enclosure
Painted steel
Dimensions
45.72mm x 20.82mm x 104.14mm (1.80 in. x 0.82 in.
x 4.10 in.)
Shipping Weight
0.22 kg (0.49 lbs.)
Operating Temperature
(Environment)
0° to +40° C (+32° to +104° F)
Operating Temperature (Chassis) 0° to +55° C (+32° to +131° F)
Operating Humidity
(Environment)
20% to 90%, Non-condensing
Storage Temperature
(Environment)
-10° to +60° C (+14° to +140° F)
Storage Humidity (Environment) 20% to 90%, Non-condensing
POWER, ESD, AND REGULATORY
Need Help?
We offer technical assistance
on all of our products or
applications!
Maximum Power Consumption
24VDC @ 0.5 Amps (Max.)
ESD Protection
15kV
Regulatory
CE, RoHS, FCC
OTHER
Call us at
800-530-8998
or email:
Standard Warranty
2 years
Diagnostic Indicators
Link LED
Included Items
Installation Guide
[email protected]
16
800.530.8998
|
www.LibAV.com
|
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
HDBASET EXTENDERS
INT-HDX100-TX / INT-HDX100-RX
INT-HDXL100-TX / INT-HDXL100-RX
100M AND 150M HDMI, IR, RS232 AND ETHERNET HDBASET EXTENDERS
INT-HDX100-TX
INT-HDX100-RX
INT-HDXL100-TX
INT-HDXL100-RX
The Intelix INT-HDX100 and INT-HDXL100
transmitters (TX) and receivers (RX) extend HDMI
over a single solid core shielded Category 5e or
greater cable using the Valens VS100TX HDBaseT
chip, support 1080p, full 3D or 4k x 2k video
signals including multichannel audio and HDCP
1.4/2.2. INT-HDX100 models support signal up to
100 meters (323 feet) and the HDXL100 models
support signal up to 150 meters (492 feet). Builtin surge protection and diagnostic LEDs ensure
hassle-free and robust installations.
Key features of the new extender series include
power over HDBaseT (PoH), bidirectional IR,
bidirectional RS232, and Ethernet pass-through
with a 2-port
network switch.
INT-HD70-TX / INT-HD70-RX
The Intelix INT-HD70-TX (Transmitter) and INTHD70-RX (Receiver) extend HDMI, IR, and RS232
over a single solid core shielded Category 5e or
greater cable using the Valens VS010TX HDBaseT
chip. The HD70 series extenders supports a 1080p
video signal, including HDCP 2.2 and multichannel
audio, up to 70m, as well as 3D and 4K x 2K (UHD)
signals up to 40m. Built-in surge protection and
diagnostic LEDs ensure hassle-free and robust
installations. Flexible power design allows the units
to be powered at either the TX or RX end, and only
one power supply is required. The power supply is
included; IR accessories (DIGIB-EMT and DIGIB-EYE)
are sold separately. The INT-HD70 series extenders
are compatible with all Intelix HDBaseT product
offerings and any product that meets the HDBaseT
specifications.
70M HDMI, IR AND RS232 HDBASET EXTENDER
INT-HD70-TX
INT-HD70-RX
EXTENDER ACCESSORIES
PSU12
RACK12 EXT
12 OUTPUT DC POWER SUPPLY UNIT
12 SLOT HDBASET
EXTENDER RACK
MOUNT KIT
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
|
800.530.8998
|
www.LibAV.com
17
HDBASET EXTENDERS
DL-HD60-ARC
HDBASET EXTENDER SET WITH AUDIO RETURN CHANNEL
The DigitaLinx DL-HD60-ARC HDBaseT extender
set transmits HDMI (1080p and UHD/30) including
HDCP 1.4, Bi-directional IR control and High
Bandwidth of 10.2Gps up to 70 meters away using
a single Category 6 twisted pair cable. Built-in
diagnostic LEDs ensure hassle-free and robust
installations. The DL-HD60-ARC supports ARC
providing a solution where users have flexibility
to enable audio upstreaming from display to
speakers.The 12V PoC integrated design allows the
units to be powered at the TX or RX, and only one
power supply is required. The 12 volt power supply
is secured with a screw-on connector to prevent
the power from being accidentally disconnected.
key features
• HDMI extension up to 70 meters
• 4K, HDCP 1.4 compliance
• Transmitter features S/PDIF audio output
• Selectable ARC from HDMI input or SPDIF output on transmitter
• Bi-directional IR extension
• Flexible PoC power only requires power on one end (Either End)
DIGI-BSR-4K
100 M HDBASET 4K SCALING RECEIVER WITH HDMI, IR, RS232 AND ETHERNET
The Intelix DIGI-BSR-4K extends HDMI over a
single solid core shielded Category 5e or greater
cable using the Valens VS100RX HDBaseT chip
and scales the source content up or down to
the native resolution of the connected display.
The DIGI-BSR-4K supports 1080p, full 3D or 4k
x 2k video signals up to 100 meters (328 feet)
including multichannel audio and HDCP 1.4.
Built-in surge protection and diagnostic LEDs
ensure hassle-free and robust installations.
Additional connections include bidirectional IR,
bidirectional RS232, and Ethernet pass-through
with a 2-port network switch.
key features
• HDBaseT receiver
• Built-in scaling up to 4kx2k
• Up/Down Scaling ability
• 100 meter max distance
• PoE powers the remote transmitter
• SPDIF and analog audio de-embedding
• Compatible with all Intelix HDBaseT products
• Affordable way to scale HDBaseT signals to match your display needs
18
800.530.8998
|
www.LibAV.com
The DIGI-BSR-4K requires local power, but it
can provide power to a compatible HDBaseT
transmitter. The power supply is included with
the extender. The bidirectional wideband IR,
bidirectional RS232, and Ethernet pass-through
capabilities make the DIGI-BSR-4K compatible
with most control systems.
|
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
HDBASET EXTENDERS
DL-HDE100
HDMI OVER TWISTED PAIR SET WITH POWER, CONTROL, AND ETHERNET
key features
• H DMI transmission up to 330 feet (100m)
• 1080p, 4Kx2K (UHD) & 3D compatible
• CEC supported
• B uilt-in surge protection
• D iagnostic LEDs
• H DCP 2.2 compliant
• B idirectional Wideband IR and RS232 pass-through
• 100-BaseT Ethernet pass-through
• Flexible power design (use power supply at TX or RX)
• Locking Power Connector
The DigitaLinx DL-HDE100 extender set transmits HDMI
(1080p, 4Kx2K (UHD) & 3D) including HDCP 2.2, Ethernet,
bidirectional IR, and RS232 up to 100 meters away using
a single twisted pair cable. Built-in surge protection and
diagnostic LEDs ensure hassle-free and robust installations.
Flexible power design allows the units to be powered at either
the TX or RX end, and only one power supply is required. The
12 volt power supply is secured with a screw-on connector
to prevent the power from being accidentally disconnected.
The DL-HDE100 is sold only as a set. Accessories are two IR
emitters, two IR receivers, and two pairs of mounting brackets
with screws. The individual transmitter and receiver are not
compatible with other HDBaseT devices due to proprietary
PoE circuitry.
DL-HD70
HDMI OVER TWISTED PAIR SET WITH POWER AND CONTROL
key features
• H DMI transmission up to 230 feet (70m)
• 1080p, 4Kx2K (UHD) & 3D compatible
• CEC supported
• B uilt-in surge protection
• D iagnostic LEDs
• H DCP 2.2 compliant
• B idirectional Wideband IR and RS232 passthrough
• Flexible power design (use power supply at TX or RX)
• Locking Power Connector
The DigitaLinx DL-HD70 extender set transmits HDMI (1080p,
4Kx2K (UHD) & 3D) including HDCP 2.2, bidirectional IR, and
RS232 up to 70 meters away using a single twisted pair cable.
Built-in surge protection and diagnostic LEDs ensure hasslefree and robust installations. Flexible power design allows the
units to be powered at either the TX or RX end, and only one
power supply is required. The 12 volt power supply is secured
with a screw-on connector to prevent the power from being
accidentally disconnected.The DL-HD70 is sold only as a set.
All accessories are included including two IR emitters, two IR
receivers, and two pairs of mounting brackets with screws.
The individual transmitter and receiver are not compatible
with other HDBaseT devices due to proprietary PoE circuitry.
HDBASET EXTENDERS ACCESSORY
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
|
800.530.8998
DL-HDRKKT
DIGITALINX RACK
MOUNT KIT FOR
DL-HDE100 / DL-HD70
|
www.LibAV.com
19
ADDITIONAL EXTENDERS / CONVERTERS
DL-HD50C
HDMI OVER SINGLE CAT 50M (150') EXTENDER SET
The DigitaLinx DL-HD50C is an HDMI
Extender over Single Cat5e/6 with IR up
to a distance of 164ft/50m. The DL-HD50C
features EDID management, which allows and
encourages source and display “handshake”
for seamless integration. Deep color video,
1080p High Definition resolution, DTS-HD or
Dolby TrueHD audio are supported with this
extender. In addition, The DL-HD50C is sold as
a set with a transmitting unit and receiving
unit. The transmitting unit is used to capture
the HDMI input with IR and carries the signals
via one cost effective Cat5e/6 cable. The
receiving unit is responsible for equalizing the
transmitted HDMI signal and reconstructing
IR control signals. The extender offers the
most convenient solution for HDMI extension
over a single Cat5e/6 with long distance
capability, and is the perfect solution for
any application.
key features
• Simple and cost-effective HDMI over single Cat Extender
• Uncompressed 1080P/60Hz up to 50 meters over single Cat5e/Cat6a
• HDMI 1.3b and HDCP compliance
• Independent HDMI equalization adjustment button.
• One-way IR pass through
• Built-in Surge protection: Voltage ± 1kV
• Compact size for easy installation.
• HDMI output on TX for local display
• Power required on TX side only
20
800.530.8998
|
www.LibAV.com
Need Help?
We offer technical assistance on
all of our products or applications!
Call us at 800-530-8998
or email:
[email protected]
|
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
AUTO SWITCHERS AND EXTENDERS
DL-AS21C
HDMI + VGA AUTO-SWITCHER WITH CEC CONTROL
The DigitaLinx DL-AS21C is a compact multi-format
switcher with support for video resolutions up to UHD
(4096x2160). Featuring one HDMI input and one VGA
input with stereo audio, the DL-AS21C automatically or
manually switches either input to a single HDMI output.
The DL-AS21C features multiple methods of control. When
set to AUTO, the switcher will automatically switch to
the newest source device added to the DL-AS21C with
VGA taking precedence should multiple sources be live
simultaneously. The DL-AS21C may be manually controlled
by switching via the front panel, RS232, or contact closure.
As an added benefit, the DL-AS21C features a built-in CEC
controller to power on/off the connected display by autoselecting the source device’s status.
key features
• H DMI supports 1080p, 3D and 4K video and 2.0/5.1 audio
• V GA supports up to 1920x1200 with audio embedding
• B uilt-in EDID settings and EDID pass-through
• H DMI output with CEC control of display
• M anual, RS232, contact closure, &automatic switching
DL-S41
BLACK DIGITALINX 4X1 HDMI AUTOSWITCHER
The new DL-S41 is a small format autoswitcher with four HDMI video inputs and
one HDMI output. This switcher supports
HDMI video resolutions up to 4K (3840x2160)
at 30 Hz, 1080p 3D, and multichannel audio.
In addition to passing EDID information from
the display, there are multiple built-in EDID
settings to simplify an installation.
The DL-S41 will de-embed digital stereo
audio to allow for an existing audio system.
This switcher also features audio return
channel (ARC) support through the analog
audio output.
key features
• A uto-switch or manual switch between four HDMI inputs
• O ne HDMI and one 3.5 mm (ARC & audio de-embedding) output
• Front panel, IR and RS232 control
• U HD, 1080p, 3D compatible; HDCP compliant
When in auto-switch mode, the DL-S41 will
switch to a HDMI input as soon as a new
source is connected. When the active source
is removed, the switcher will select the first
source on the lowest numbered input. The
DL-S41 may also be controlled via RS232, IR
with the included remote, or from the source
button on the front of the switcher.
Need Help?
We offer technical assistance on
all of our products or applications!
Call us at 800-530-8998
or email:
[email protected]
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
|
800.530.8998
|
www.LibAV.com
21
AUTO SWITCHERS AND EXTENDERS
INT-HD52
5X1+1 AUTO SWITCHING/SCALING PRESENTATION SWITCH WITH HDBASET W/POE & HDMI OUTPUT
key features
• 3 HDMI, 1 DP w/audio, 1 VGA w/audio input
• HDBaseT with PoE and a mirrored HDMI output
• Integrated scaling up to 1900X1200
• M ic / Line level audio input with audio embedding and
phantom power
• A udio De-embedding w/balanced audio out
• Fast/seamless switching time <1s
• R S232 & IR tunneling over HDBaseT for control of connected
devices/displays
• Controlable via RS232, TCP/IP, IR, or Front Panel
• A uto switching
• Ships with under table mounting ears
• Integrated web GUI for setup and/or control
• U p to 70m signal extension with PoE via HDBaseT
The Intelix INT-HD52 is a compact auto switcher scalar that
allows the integration of analog and digital devices into a
high-definition environment. Mounting options include under
table or resting on a shelf. The INT-HD52 allows selection of
five different A/V sources, and will simultaneously scale the
selected video to HDMI and HDBaseT outputs. The unit features
three HDCP compliant HDMI inputs, one Display Port input and
one VGA input. The VGA input can be configured to support
YPbPr (component video), YC (S-video), and C (composite video)
video formats with the appropriate VGA breakout cable. There
are eight fixed output resolutions to choose from, and several
aspect ratio modes, which will ensure your content is displayed
properly. The HDBaseT output will allow you to extend audio,
video, and control signals up to 70m away.
DL-AS61
4 HDMI + 2 VGA INPUT AUTO-SWITCHER W/VGA SCALING
The DigitaLinx DL-AS61 is a compact multi-format
switcher with support for video resolutions up to UHD
(3840x2160). With multiple built-in EDID settings, including
an EDID pass-through option, the highest quality digital
video signal will be routed directly to the display. When
a VGA video signal is connected, the video signal will be
scaled up to 1920x1200. The DL-AS61 supports stereo and
multichannel audio on the HDMI inputs.
key features
• H DMI supports 1080p, 3D and 4K video and 2.0/5.1 audio
• V GA scaling up to 1920x1200 with audio embedding
• B uilt-in EDID settings and EDID pass-through
• H DMI output with analog and optical audio outputs
• M anual, RS232, IR, and automatic switching
22
800.530.8998
|
www.LibAV.com
|
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
AUTO SWITCHERS AND EXTENDERS
DL-AS31-2H1V
The DL-AS31-2H1V is a multiformat auto-switcher with two
HDMI inputs and one VGA with analog audio input, one HDMI
output, and one balanced analog audio output. This autoswitcher supports HDMI resolutions up to 4Kx2K at 30 Hz and
multichannel audio and VGA video resolutions up to 1920x1200
at 60 Hz. In addition to passing EDID information from the
display, there are multiple built-in EDID settings to simplify an
installation.
3X1 AUTOSWITCHER - 2 HDMI AND 1 VGA INPUT
key features
• 2 HDMI and 1 VGA with audio input
• 1 HDMI and stereo audio output
• B uilt-in audio de-embedding
• V GA Scaling up to 1920x1200
• Integrated CEC control
• A utomatic and manual switching via RS232 and contact closure
• Includes under table mounting ears
DL-AS31-2H1DP
3X1AUTO-SWITCH 2 HDMI AND 1 DISPLAYPORT INPUT
The DL-AS31-2H1DP is a multiformat auto-switcher with two
HDMI inputs and one DisplayPort with analog audio input, one
HDMI output, and one balanced analog audio output. This autoswitcher supports HDMI and DisplayPort video resolutions up to
4Kx2K at 30 Hz and multichannel audio. In addition to passing
EDID information from the display, there are multiple built-in
EDID settings to simplify an installation.
key features
• 2 HDMI & 1 DisplayPort inputs
• 1 HDMI and stereo audio output
• H DMI and DP support 1080p and 4K video with stereo audio
• B uilt-in EDID settings and EDID pass-through
• B uilt-in audio de-embedding
• A utomatic and manual switching via RS232 and contact closures
• Includes under table mounting ears
DL-AS31-1H1DP1V
The DL-AS31-1H1DP1V is a multiformat auto-switcher with one
HDMI input, one DisplayPort with analog audio input, one VGA with
analog audio input, one HDMI output, and one balanced analog audio
output. This auto-switcher supports HDMI and DisplayPort video
resolutions up to 4Kx2K at 30 Hz and multichannel audio and VGA
video resolutions up to 1920x1200 at 60 Hz. In addition to passing
EDID information from the display, there are multiple built-in EDID
settings to simplify an installation.
3X1 AUTOSWITCHER - UNDER-TABLE.
[1] HDMI, [1] DP, AND [1] VGA
key features
• 1 HDMI, 1 DisplayPort, & 1 VGA input
• 1 HDMI and stereo audio output
• Built-in audio de-embedding
• Automatic and manual switching via RS232 and contact closure
• Includes under table mounting ears
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
|
800.530.8998
|
www.LibAV.com
23
AUTO SWITCHERS AND EXTENDERS
AS-2H
The Intelix AS-2H is an under table mounted switcher designed to be
the primary PC interface for classrooms, boardrooms, and
conference centers. It features two HDMI inputs, 1 HDBaseT output
with a mirrored HDMI output. The AS-2H utilizes HDBaseT technology
to extend the digital output up to 70 meters. This unit is compatibile
with all Intelix HDBaseT receivers. The unit features multiple EDID
modes to eliminate user confusion, and incompatible video formats.
DUAL HDMI AUTO-SWITCHER WITH
HDMI & HDBASET OUTPUT
key features
• Two HDMI inputs
• H DMI and HDBaseT output - 70m Max Distance
• A utomatically switches input to active video
• R S232, Auto, and Dry Contact Closure for control of device
• P oH (Power over HDBaseT) or 24V DC local power
• D isplay Control Software to control TV or projector with RS232
commands - automatically turns display on/off
• Customizable power management system when not in use
AS-1H1V
The Intelix AS-1H1V is an under table mounted switcher designed to be the
primary PC interface for classrooms, boardrooms, and conference centers. It
features VGA + Audio to HDMI conversion with VGA scaling up to 1920x1200
and an HDMI input. The AS-1H1V utilizes HDBaseT technology to extend the
digital output up to 70 meters, and has a mirrored HDMI output. This unit is
compatibile with all Intelix HDBaseT receivers. The unit features multiple EDID
modes to eliminate user confusion, and incompatible video formats.
HDMI/VGA AUTO-SWITCHER WITH VGA
SCALING, HDMI & HDBASET OUTPUT
key features
• H DMI (including audio) and VGA/3.5mm Stereo input
• H DMI and HDBaseT output - 70m Max Distance
• A utomatically switches input to active video
• V GA scaling up to 1920x1200
• R S232, Auto, and Dry Contact Closure for control of device
• P oH (Power over HDBaseT) or 24V DC local power
• D isplay Control Software to control TV or projector with
RS232 commands - automatically turns display on/off
• Customizable power management system when not in use
AS-1H1DP
The Intelix AS-1H1DP is an under table mounted switcher designed
to be the primary PC interface for classrooms, boardrooms, and
conference centers. It features DisplayPort + Audio to HDMI
conversion and an HDMI input. If the DisplayPort signal does not
support embedded audio, the analog audio input port can be
accessed via RS232. The AS-1H1DP utilizes HDBaseT technology to
extend the digital output up to 70 meters. This transmitter device
is compatibile with all Intelix HDBaseT receivers. The unit features
multiple EDID modes to eliminate user confusion, and incompatible
video formats.
HDMI/DISPLAYPORT AUTO-SWITCHER
WITH HDMI & HDBASET OUTPUT
key features
• H DMI and DisplayPort w/ 3.5mm Stereo input
• H DMI and HDBaseT output - 70m Max Distance
• A utomatically switches input to active video
• R S232, Auto, and Dry Contact Closure for control of device
• P oH (Power over HDBaseT) or 24V DC local power
• D isplay Control Software to control TV or projector with
RS232 commands - automatically turns display on/off
• Customizable power management system when not in use
24
800.530.8998
|
www.LibAV.com
|
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
AUTO SWITCHERS AND EXTENDERS
AS-2H-WP-W
AS-2H-WP-B
The Intelix AS-2H-WP is a two-gang, Decora-style wallplate
designed to be the primary PC interface for classrooms,
boardrooms, and conference centers. It features two HDMI
inputs. The AS-2H-WP utilizes HDBaseT technology to extend
the digital output up to 70 meters away using solid core shielded
Category 5e or greater cable. This transmitter device is compatible
with alll Intelix HDBaseT receivers.
DUAL HDMI AUTO-SWITCHING
WALLPLATE W/ HDBASET OUTPUT
key features
AS-2H-WP-B
AS-2H-WP-W
AS-1H1V-WP-W
AS-1H1V-WP-B
• Two HDMI inputs
• HDBaseT output - 70m Max Distance
• Automatically switches input to active video
• RS232, Auto, and Dry Contact Closure for control of device
• PoH (Power over HDBaseT) or 12V DC local power
• D isplay Control Software to control TV or projector with RS232 commands automatically turns display on/off
• Customizable power management system when not in use
The Intelix AS-1H1V-WP is a two-gang, Decora-style wallplate
designed to be the primary PC interface for classrooms,
boardrooms, and conference centers. It features VGA + Audio
to HDMI conversion with VGA scaling up to 1920x1200 and an
HDMI input. The AS-1H1V-WP utilizes HDBaseT technology to
extend the digital output up to 70 meters away using solid
core shielded Category 5e or greater cable. This transmitter
device is compatible with alll Intelix HDBaseT receivers.
HDMI/VGA AUTO-SWITCHING/
SCALING WALLPLATE WITH HDBASET OUTPUT
key features
AS-1H1V-WP-W
AS-1H1V-WP-B
• HDMI (including audio) and VGA/3.5mm Stereo input
• HDBaseT output - 70m Max Distance
• VGA scaling up to 1920x1200
• Automatically switches input to active video
• RS232, Auto, and Dry Contact Closure for control of device
• PoH (Power over HDBaseT) or 12V DC local power
• D isplay Control Software to control TV or projector with RS232 commands automatically turns display on/off
• Customizable power management system when not in use
AS-1H1DP-WP-W
AS-1H1DP-WP-B
The Intelix AS-1H1DP-WP is a two-gang, Decora-style wallplate
designed to be the primary PC interface for classrooms,
boardrooms, and conference centers. It features DisplayPort
+ Audio to HDMI conversion and an HDMI input. If the
DisplayPort signal does not support embedded audio, the
analog audio input port can be accessed via RS232. The AS1H1DP-WP utilizes HDBaseT technology to extend the digital
output up to 70 meters away using solid core shielded Category
5e or greater cable. This transmitter device is compatible
with alll Intelix HDBaseT receivers.
HDMI/DISPLAYPORT AUTO-SWITCHING
WALLPLATE W/ HDBASET OUTPUT
key features
AS-1H1DP-B-WP
AS-1H1DP-WP-B
• HDMI and DisplayPort w/ 3.5mm Stereo input
• HDBaseT output - 70m Max Distance
• Automatically switches input to active video
• RS232, Auto, and Dry Contact Closure for control of device
• PoH (Power over HDBaseT) or 12V DC local power
• D isplay Control Software to control TV or projector with RS232 commands automatically turns display on/off
• Customizable power management system when not in use
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
|
800.530.8998
|
www.LibAV.com
25
AUTO SWITCHERS AND EXTENDERS
DL-A31
DIGITALINX BRAND BY LIBERTY HDMI 3X1 MATRIX SWITCH
The DigitaLinx DL-A31 is a three input
by one output slim HDMI matrix with
Ultra HD 4K support. The DL-A31 is HDMI
2.0, HDCP 2.2, and DVI 1.0 compliant. The
matrix switcher offers video formats such
as 4k/30Hz with 24bit at 4:4:4/ 4:2:2 and
up to 4k/60Hz with 12bit at 4:2:0. The
DL-A31 can be controlled via IR Remote or
front panel. The matrix switcher provides
smart auto switching functionality along
with a wide range of audio support, LPCM
7.1CH, Dolby TrueHD, and DTS-HD Master
Audio.
key features
• 3 HDMI input by 1 HDMI output
• HDMI 2.0, HDCP 2.2, and DVI 1.0 compliant
• Supports 4k/30Hz with 24bit at 4:4:4/ 4:2:2 and up to
4k/60Hz
with 12bit at 4:2:0
• Smart auto switching
• Supports LPCM 7.1CH, Dolby TrueHD, and DTS-HD
Master Audio
DL-A51 The DigitaLinx DL-A51 is a five input by
one output slim HDMI matrix with Ultra
HD 4K support. The DL-A51 is HDMI 2.0,
HDCP 2.2, and DVI 1.0 compliant. The
matrix switcher offers video formats such
as 4k/30Hz with 24bit at 4:4:4/ 4:2:2 and
up to 4k/60Hz with 12bit at 4:2:0. The
DL-A51 can be controlled via IR Remote or
front panel. The matrix switcher provides
smart auto switching functionality along
with a wide range of audio support, LPCM
7.1CH, Dolby TrueHD, and DTS-HD Master
Audio.
DIGITALINX BRAND BY LIBERTY HDMI 5X1 MATRIX SWITCH
key features
• 5 HDMI input by 1 HDMI output
• HDMI 2.0, HDCP 2.2, and DVI 1.0 compliant
• Supports 4k/30Hz with 24bit at 4:4:4/ 4:2:2 and up to
4k/60Hz
with 12bit at 4:2:0
• Smart auto switching
• Supports LPCM 7.1CH, Dolby TrueHD, and DTS-HD
Master Audio
26
800.530.8998
|
www.LibAV.com
|
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
DISTRIBUTION AMPLIFIERS / SPLITTERS
HD12S / HD14S / HD18S
1X4, 1X8 HDMI 2.0 DISTRIBUTION AMPLIFIER
The Intelix HD14S (1x4) or HD18S (1x8)
are distribution amplifiers that have
an HDMI splitter with HDMI 2.0 and
HDCP 2.2. They support data rates up to
18Gbps and resolutions of [email protected]
(4:2:0). These distribution amplifies
features EDID management which
provides multiple EDID options for
various resolutions output and HDCP
encryption between all devices, ensuring
the HDMI source reliably outputs the
correct content for the display.
HD12S
HD14S
The Intelix HD14S and HD18S include
input cable equalization and signal
regeneration compensation, which
reduces the need for additional
signal conditioning equipment by
compensating for signal loss when
using long input cables or cascading
multiple units.
HD18S
key features
• 1x4 HDMI distribution amplifier/splitter
• 4 K, HDMI 2.0, HDCP 2.2 compliant
• A djustable EDID management
• F ield firmware upgradeable
• Locking power supply
• Includes mounting hardware
18G 4K60 4:4:4
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
|
800.530.8998
|
www.LibAV.com
27
MATRIX SWITCHERS
FLX-64
6 INPUT, 4 OUTPUT HDMI/HDBASET MATRIX SWITCHER AUDIO EMBED/DE-EMBED WITH BREAKAWAY ROUTING
The Intelix FLX-64 was designed for use in conference rooms
that have two in-room inputs extended to the rack, a few local
sources at the rack, two discrete displays, a VTC codec & a
recorder. The FLX-64 can be controlled via front panel buttons,
front panel IR, external IR, remote IR through HDBaseT
extenders, RS232 & Ethernet.
key features
• 4 HDMI inputs (2 w/ audio embedding) and 2 HDBaseT Lite inputs w/ PoE
• 4 HDBaseT Lite outputs w/ PoE & 2 mirrored HDMI outputs
• 60 m (200 ft) maximum extender distance
• Audio de-embedding on each output, including breakaway
• Front panel, IR, TCP/IP, and RS232 control
• IR and RS232 routing
• IR and RS232 tunneling over HDBaseT (inputs and outputs)
• Control page and configuration accessible from web browser
• Advanced HDCP management
DL-44E-KIT
4X4 4K HDBT MATRIX SWITCH KITTED WITH 3 HDBASET POE RECEIVERS
The DL-44E-KIT is a professional 4K HDBaseT Home Distribution Hub Kit, which consists
of a 4K HDBaseT Matrix Switcher, 3 HDBaseT Receivers and accessories. The DL-44EKIT is a professional 4x4 HDBaseT Matrix Switcher that consist of the following inputs
and outputs, 4 HDMI IN ([email protected] signal at max), 3 IR IN, 1 IR EYE, 4 IR OUT, 3
HDBaseT OUT, 1 HDMI OUT, 1 SPDIF OUT, 1 L&R RCA OUT, and TCP/IP, RS232 control port
via phoenix connector. The DL-44E-KIT offers manual HDCP management and autodetecting along with easy installation with rack-mounting design.
key features
The DL-HD70LS-RX is an HDBaseT Receiver that consists of the following inputs and
outputs, 1 HDBaseT IN, 1 IR IN, 1 IR OUT and HDMI OUT. The receiver is powered directly
by the DL-44E-KIT. All HDMI inputs can be selected by either the front panel buttons,
IR, RS232 or GUI. The selected source is delivered to HDBaseT zoned outputs 1-3 & HDMI
Output. The DL-44E-KIT is capable of delivering 4K signals up to 40m, 1080p up to 70m
and powering the receivers via a single CAT5e cable. It is recommended to use good
quality CAT6 cable. The Matrix Switcher supports EDID management and is HDCP 2.2, 1.4
compliant. Audio sources can be selected via RS232 commands and TCP/IP at the Matrix
Switcher or by 3rd Party control.
• Front panel, IR, TCP/IP, and RS232 control
• IR tunneling over HDBaseT
• Control page and configuration accessible
28
800.530.8998
|
www.LibAV.com
|
• Four HDMI inputs with 4K & HDCP 2.2
support
• 3 HDBaseT with PoE Outputs
• 1 HDMI Output
• 3 HDBaseT Receivers kitted
with the switch
• 70m maximum extender distance
• A nalog and digital audio de-embedding
on the HDMI output
from web browser
• Advanced HDCP management
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
MATRIX SWITCHERS
DL-HDM44-SS / DL-HDM66-SS / DL-HDM88-SS
18G 4K60 4:4:4
4X4, 6X6, 8X8 HDMI MATRIX HDMI 2.0, HDCP 2.2 COMPLIANT
The DigitaLinx DL-HDMxx-SS series of matrix switchers are
available in four, six or eight HDMI ouputs with HDCP 2.2 and
a full-loading capability [email protected] output for each channel.
These switchers feature advanced independent DIP switch
for EDID management with HDCP handling, including the
ability to turn input HDCP compliance ON and OFF to ensure
maximum functionality with a wide range of sources. These
matrix switchers can be controlled via front panel buttons,
front panel IR, external IR, remote IR, RS232, and Ethernet.
DL-HDM44-SS
key features
• 4x4 HDMI matrix switching
• 4K, HDMI 2.0, HDCP 2.2 compliant
• Built-in EDID management
• Front panel, IR, RS232, and Ethernet control
• Built-in webserver control
• 1 RU design
DL-HDM66-SS
PRE-BUILT CONTROL SYSTEM DRIVERS FOR
DL-HDM88-SS
DL-HDM44-FS / DL-HDM88-FS
4X4, 8X8 HDMI MATRIX WITH SEAMLESS SWITCHING AND SCALING PER OUTPUT UP TO 4K
The DigitaLinx DL-HDMxx-FS series of matrix switchers
offer four by four or eight by eight outputs with seamless
4K scaling. These HDMI matrix switchers support up to
[email protected] and HDCP2.2. With a high-performance
[email protected] video scaler built into each output channel, it
easily scales various resolutions to match the best video
and picture quality across all displays.
DL-HDM44-FS
key features
• 4x4 HDMI matrix switching
• Stereo audio de-embedding and outputs per channel
• Scaling up to 4K per channel
• Front panel, IR, RS232, and Ethernet control
• Built-in webserver control
• Fast switching (<1s) with matching or mixed output resolutions
• Built-in EDID management, HDCP 2.2 compliant
• Manageable HDCP compliance
PRE-BUILT CONTROL SYSTEM DRIVERS FOR
DL-HDM88-FS
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
|
800.530.8998
|
www.LibAV.com
29
MATRIX SWITCHERS
INT-44HDX / INT-66HDX / INT-88HDX
4X4, 6x6, 8x8 HDBASET MATRIX SWITCH; 100M, 4K, HDCP 2.2, POH
INT-44HDX
NT-66HDX
INT-88HDX
key features
The Intelix INT-xxHDX series is a 4x4, 6x6 or 8x8 output
HDBaseT/HDMI matrix switcher with HDCP 2.2 and UHD/30
video support. This series provides HDBaseT twisted pair extension for
each output, and simultaneous HDMI on the first two outputs, allowing
the same signal to be routed to the HDMI connector and a remote
destination with an HDBaseT receiver. The HDBaseT ports support up to
UHD/30 HDMI video with audio, bidirectional wide-band IR, matrix control
via IR, RS232 tunneling, and HDCP (1.4 and 2.2) up to 100 meters (328 feet).
Each HDBaseT output port supplies power to the attached extender,
eliminating the need for a power supply at the display end.
• Four HDMI inputs with HDCP 2.2 support
• Four HDBaseT with PoH, with two mirrored HDMI, outputs
• 100 m (328 ft) maximum extender distance
• Analog and digital audio de-embedding on each output
• Front panel, IR, TCP/IP, and RS232 control
• IR and RS232 routing
• IR and RS232 tunneling over HDBaseT
• C ontrol page and configuration accessible from web
browser (Web GUI)
• Advanced HDCP management
• UL Certified
PRE-BUILT CONTROL SYSTEM DRIVERS FOR
Match any Intelix HDBaseT receiver with these Matrix Switchers
INT-HD70-RX
HDMI SLIM 70M, POH, IR AND RS232
CONTROL HDBASET EXTENDER - RECEIVER
70m Receiver
INT-HDX100-RX
HDMI SLIM 100M, POH, IR AND CONTROL
HDBASET EXTENDER - RECEIVER
100m Receiver
DIGI-BSR-4K
HDBASET 4K SCALING RECEIVER
W/POE, AUDIO-DE-EMBED
4K Scaling Receiver
30
800.530.8998
|
www.LibAV.com
|
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
AUDIO AMPLIFICATION
AUD-220
2 INPUT AUDIO AMPLIFIER, 2x20W (4 OHM)
The Intelix AUD-220 is a 2x20 watt Class D amplifier with 8Ω speaker output.
The amplifier features two analog audio inputs and a balanced microphone input
with ducking functions. Additional features of the AUD-220 include input and
microphone volume control, bass and treble adjustments, microphone mixing with
source audio, and three modes of microphone input support (48 dB gain, 48 dB
gain with 48V phantom power, and line level). The AUD-220 has three methods of
control: push button, RS232, and IR with the optional AUD-220-IR accessory kit.
key features
• Two analog audio inputs
• Microphone input with ducking or mixing
• Bass, treble adjustments
• Line input and/or microphone muting
• Stereo, 2x mono, or bridged mono speaker output
• Line level loop output to daisy chain
• Front panel and optional IR control
AUD-340
3 INPUT AUDIO 70/100V AMPLIFIER, 40W
The Intelix AUD-340 is a 40 watt Class D amplifier
with 70V or 100V outputs. The amplifier features two
analog audio inputs, one digital audio input, and a
balanced microphone input with ducking functions.
Additional features of the AUD-340 include input
and microphone volume control, bass and treble
adjustments, microphone mixing with source audio,
and three modes of microphone input support (48 dB
gain, 48 dB gain with 48V phantom power, and line
level). The AUD-340 has three methods of control:
push button, RS232, and IR with the optional AUD340-IR accessory kit.
key features
• Two analog audio inputs; one digital audio input
•M
icrophone input with ducking or mixing
• B ass, treble adjustments
• Line input and/or microphone muting
• 70V or 100V output
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
|
800.530.8998
|
www.LibAV.com
31
ROOM CONTROL
LB-ICP
LINK BRIDGE CONTROL PROCESSOR
key features
• Easy to install control system processor
• Program entire control system with an easy built-in web GUI
• Features:
(2) RS232
(2) Relay
(2) Digital I/O
(1) IR
(1) ETHERNET
• P air with the LB-KP8 keypad for easy
and simple push button control system
LB-KP8
LB-KP8E
LINK BRIDGE RS232 8 BUTTON KEYPAD CONTROLLER
LINK BRIDGE 8-BUTTON WALL PLATE W/
INTEGRATED ETHERNET CONTROLLER
key features
• Single gang decora insert
• RS232 interface
• U ser configurable buttons with
key features
• Replaceable button labels
• P air with the LB-IPC control
• A vailable with PoE function or
• 1-gang wall plate Ethernet
controller with 8 buttons
• C omes with relays to control
dual color and backlit
peripheral device on/off
DC power supply selection
• S upports Telnet or WebGUI control
• S upports scheduling control and settings
• A djustable LED dim light in keypad buttons
processor for an easy and simple
push button control system
32
800.530.8998
|
www.LibAV.com
|
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
ROOM CONTROL
DL-UHDILC 18G 4K60 4:4:4
IN-LINE HDMI AUTO SENSING ROOM CONTROLLER
The DigitaLinx DL-UHDILC is an HDMI in-line controller
that can automate room peripherals and sink devices
when a video signal is introduced to the unit. The
DL-UHDILC is 4K compatible, supports HDCP version 2.2,
has an analog and digital de-embedded audio output
and has 15 built in EDID presets that can be adjusted by
the rotary dial on the front panel.
Audio Output
(1) S/PDIF (1) Analog
Audio Output Connector
(1) RCA (1) Stereo 3.5mm
Video Inputs
(1) HDMI
Video Input Connector
(1) HDMI type A
When the DL-UHDILC auto-detects an input video
signal, the DL-UHDILC will automatically turn a display
or projector on either by CEC or by pre-loaded RS232
serial commands. The DL-UHDILC will trigger the first
relay port to switch a projector screen or window shade
down. When a video signal is no longer present after a
specified amount of time, the DL-UHDILC will turn off
the display or projector by either CEC or pre-loaded
RS232 commands and will trigger the second relay port
to switch a projector screen or window shade up.
Video Output
(1) HDMI
Video Output Connector
(1) HDMI type A
Output Resolution Support
4096x2160; 3840x2160; 1920x1200; 1920x1080;
1680x1050; 1600x1200; 1600x900; 1440x900; 1400x1050;
1366x768; 1360x768; 1280x1024; 1280x960; 1280x800;
1280x768; 1024x768; 800x600
Standards
Compliant with HDMI 1.4 & HDCP2.2
TECH SPECS
SUPPORTED AUDIO AND VIDEO
key features
• Stand alone unit
• Automates room peripherals when video signal is introduced to system
• Passes HDMI signals up to 18G 4K60 4:4:4
• Built in CEC controller from HDMI out.
• Built in RS232 controller to control display device
• B uilt in RELAY control for room peripherals such as projector
screen or window shade
CONTROL
Control Port
(2) RELAY (1) RS232
Control Connector
(2) 3 pin phoenix connector (RELAY)
• De-embeds audio to coax S/PDIF or Stereo
• Switch for EDID Management with 15 EDID presets
(1) 3 pin phoenix connector (RS232)
ADDITIONAL EXTENDERS / CONVERTERS
DL-HDCP-C
The DigitaLinx
DL-HDCP-C is a 1x1
HDMI converter
that features highdefinition HDMI
transmission and HDCP
conversion. The DLHDCP-C HDMI input
supports HDMI 2.0 &
HDCP 2.2 along with
HDMI output support
of HDMI 1.4 & HDCP
1.4. The DL-HDCP-C
transmits signal up
to 15m with a max
resolution support of
[email protected]
HDCP 2.2 TO 1.4 CONVERTER
key features
• C onverts HDCP 2.2 to HDCP
1.4 for integration into
legacy systems
• HDMI input and HDMI output
• Compact design
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
|
DL-SP
HDMI SURGE PROTECTOR
800.530.8998
key features
The DigitaLinx DL-SP is an
HDMI Surge Protector. The
DL-SP is an ideal solution
designed to protect HDMI
devices against electrostatic discharge, surges
& spikes from mains, or
lightning strikes that cause
electrical transients up to
15000 Volts (air) and 8000
Volts (contact).
• P rotects the input and output from ESD and lightning surges
• H DMI 1.4 and HDCP compliant
•M
eets IEC 61000-4-2, 61000-4-4, and 61000-4-5 surge protection
requirements
|
www.LibAV.com
33
USB 3.0 EXTENSION
DL-USB3.0
DIGITALINX 15 M USB 3.0 ACTIVE EXTENSION CABLE
The DL-USB3.0 is a USB 3.0 active copper
cable that offers extension up to 15
meters. The DL-USB3.0 is bus powered
from the host PC side and USB 3.0 power
connector is available if additional power
is required. The DL-USB3.0 supports USB
3.0 throughputs up to 5Gbps, locking USB
connector, rugged grade cabling and slot
port for convenient cable tie mounting.
The DL-USB3.0 supports only USB 3.0
devices. USB 2.0 and 1.1 devices will not
function using this extender.
DIGI-FO-USB3.0
USB 3.0 Fiber Optic Extender Set
The Intelix DIGI-FO-USB3.0 is a two-port
USB 3.0 SuperSpeed extension solution,
enabling USB 3.0 connections at up to 5
Gbps over 100m/330ft of OM3 multimode
fiber optic cable. The DIGI-FO-USB3.0
features two locking USB 3.0 ports
delivering 900mA power to each port and
a true plug-and-play solution. The DIGIFO-USB3.0 is not backwards compatible
with USB 2.0 and USB 1.1.
key features
• A ctive USB 3.0 extension up to 100 meters (OM3 MM)
• Supports USB 3.0, not backwards with USB 1.1/2.0
• 2-port hub on client end
• H ost-side powered via USB port from host PC
• Includes client-side power supply with locking
power connector
• Transparent USB; Plug and Play (no software
drivers needed)
• Compatible with all major operating systems
34
800.530.8998
|
www.LibAV.com
|
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
USB 2.0 EXTENSION
DIGI-HDUSB
HDMI with USB 2.0 100m Extention System
The Intelix DIGI-HDUSB extends HDMI
& computer USB 2.0 signals up to 100m
(330ft) over twisted pair cabling. The
DIGI-HDUSB 3-port USB/video extender
system supports full uncompressed HD
video & USB 2.0 (up to 30Mbps) suitable
for video applications in conjunction with
keyboards, mice & USB 1.1 web cameras.
The DIGI-HDUSB supports HDMI video
features such as 1080p, 4K, deep color &
CEC/HDCP pass-through. The DIGI-HDUSB
supports both USB 1.1 & 2.0 devices.
key features
• Extension up to 100m over CAT5e or greater cable
• Supports both USB 1.1 & 2.0 signals up to 30Mbps
• H DMI supports 1080p, 3D & 4K
• CEC/HDCP pass through
• P lug-and-Play feature, no drivers required
• P owered on both transmitter & receiver
DIGI-USB2-4P
USB 2.0 4-port Extension System
The Intelix DIGI-USB2-4P extends computer
USB 1.1 signals up to 100m (330ft) over twisted
pair cabling to four remote devices. The DIGIUSB2-4P utilizes inexpensive twisted pair
cabling & has a throughput of up to 480Mbps.
The DIGI-USB2-4P is perfect for keyboard &
mouse extension, remote data ports, up to 4
USB hugs, security applications & interactive
white board applications.
key features
• E xtension up to 100m over Cat 5e/Cat 6
• Supports USB 1.1 and 2.0 signals up to 480Mbps
• Integrated 4-port USB hub
• P lug-and-play, no drivers required
• P owered on port (client) end
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
|
800.530.8998
|
www.LibAV.com
35
NIVEO
NR-10
SMALL FORM FACTOR GIGABIT ROUTER, 1GB WAN, INTEGRATED 4 PORT GB SWITCH WITH POE+
The NR-10 is a 4 Gigabit PSE (Power Source Equipment)
LAN ports & 1 Gigabit (Powered Device) WAN port PoE+
NAT router that is designed for small or medium network
environment. The compact size of the product makes it
the ideal router where space is limited. The NR-10 features
4-port PoE+ IEEE 802.3at supplying up to 30 watts per port.
This product can convert standard 100~240V/AC power into
low-voltage DC that runs over existing LAN cable to power
up IEEE 802.3at compliant network accessories. By adding
a NR-10 to an existing network, installing networking
products such as Access Points and IP cameras can be easily
managed and set up. Wireless device deployments are
easily located with available power outlets and network
administrators don’t need to use heavy AC power adapters
anymore. When connected with a PSE to its PD WAN port,
the NR-10 can be powered without its external power
adaptor, therefore eliminating the need to find a power
outlet for the router.
TECH SPECS
SYSTEM CAPACITY & PERFORMANCE
Processor
880 MHz, Dual-Core
L2 Cache
256 KB L2 Cache shared by Dual-Core
INTERFACE
10M/100M/1000M RJ45
PSE LAN Ports
4
10M/100M/1000M RJ45
PD WAN Ports
1
key features
• G igabit LAN PSE ports & 1 Gigabit WAN PD port PoE+ Gateway
• 1 Gigabit WAN PD Port that allows NR-10 acquiring power from a PSE.
• 4 Gigabit LAN PSE Ports that support IEEE 802.3af/at PoE, providing up to
30W per port
• Supports IEEE 802.3az EEE (Energy Efficient Ethernet), save power while
network traffic isn’t busy
• Supports voice VLAN
• M anagement features such as Max/Min Bandwidth Control, QoS,
Broadcast/Multicast/Unknown Frames Storm Control
NRS5FP
NRS8FP
NIVEO 4 PORT + UPLINK POE NETWORK SWITCH
NIVEO 8 PORT + UPLINK POE NETWORK SWITCH
key features
key features
• PoE+ (IEEE 802.3af/at (Type 1) on 8 downlink ports
• Uplink port
• 1.8 Gbps backplane bandwidth
• Total PoE Power Budget: 120w
• 10/100 Mbps bandwidth per port (including uplink)
• PoE+ (IEEE 802.3af/at (Type 1) on 4 downlink ports
• Uplink port
• 1 Gbps backplane bandwidth
• Total PoE Power Budget: 60w
• 10/100 Mbps bandwidth per port (including uplink)
36
800.530.8998
|
www.LibAV.com
|
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
NIVEO
NWA200
IN-WALL LOW PROFILE
FAT ACCESS POINT
key features
• In-wall WAP with RJ45/USB Power/RJ11 Connectivity
• 2.4 GHz, 802.3af PoE, max power 9W, transmit 18dbm
• Inconspicuous design for residential/commercial installs
• 2 3dbi omni-directional antennas
• Multiple SSID
• Dual Power, DC or PoE power
NWA300
11AC 1200MBPS MANAGEABLE
POE CEILING WIRELESS AP
key features
• Speed up to 1200 Mbps
• Ultra thin, low prole design
• Very easy, intuitive setup
• PoE or DC powered
• Stand-alone, controller managed or cloud managed
• Zero Gap Roaming
NWAC7000
WIRELESS AP ACCESS CONTROLLER
key features
• Wireless Access Point Management
• Auto-IP detection and assignment
• NWAC7000 can set AP’s SSID, Password, channel at the same time
• Real Time Monitor and Analyze
• Support Web management and Web Remote Management
NPI-H1
key features
NIVEO PROFESSIONAL GIGABIT
POE POWER INJECTOR
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
• Up to 30W of PoE Power
• IEEE 802.3at Compliant
• Compatible with IEEE 802.3af or legacy PoE applications
• Safe on low power devices only power they need
• Safe and reliable power to WLAN access points
• Automatic detection and protection safety LAN ports
• Supports 10/100/1000Base-T LAN environment
• Desktop, shelf and wall mounting
|
800.530.8998
|
www.LibAV.com
37
NIVEO ETHERNET SWITCHES
NIVEO ETHERNET SWTICHES
Front and Rear Port Facing Switches Matrix
Number of
Gb Ports
Management
PoE+
Budget
NRSFP
4 FE
-
60W
-
-
-
Front
NRS8FP
8 FE
-
120W
-
-
-
Front
NGSE8H
8
-
130W
-
-
-
Front
NGSME8H
8
Full Layer L2+
130W
2
-
-
Front
NGS16TP
16
-
-
-
-
-
Front
NGSME16T2H
16
Full Layer L2+
250W
2
-
-
Front
NGS18T16
16
-
18
-
-
Front
NGS24TP
24
-
-
-
-
-
Front
NGSM24T2
24
Full Layer L2+
-
2
-
-
Front
NGSME24T2H
24
Full Layer L2+
430W
2
-
-
Front
NGSM24G4S
24
Full Layer L2+/
Stackable
-
-
2
2
Front
NGSME24G4S
24
Full Layer L2+/
Stackable
430W
-
2
2
Front
NGSM48T2
48
Full Layer L2+
-
-
2
-
Front
NGSME48T2H
48
Full Layer L2+
430W
-
2
-
Front
NGSE8H-AV
8
-
130W
-
-
-
Rear
NGSME16T2HAV
16
Full Layer L2+
250W
2
-
2
Rear
NGSM24T2-AV
24
Full Layer L2+
-
2
-
2
Rear
NGSME24T2HAV
24
Full Layer L2+
430W
2
-
2
Rear
N10GSW4T14
18
-
4
14
14
Front
N10GSM1T24
25
-
1
24
24
Front
N10GSM4QT48
48
-
-
48
48
Model
Image
Web Smart
Management
Web Smart
Management
Web Smart
Management
L3
1Gb SFP- 10Gb SFP- 1Gb SFP - Ports Port Facing
Ports
Ports
Stackable
800.530.8998 | www.LibAV.com | SPECIFICATIONS & IMAGES SUBJECT TO CHANGE | IMAGES NOT TO SCALE | L0202
38
800.530.8998
|
www.LibAV.com
|
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
SP CONTROLS
SP CONTROLS PRODUCT OFFERING AT-A-GLANCE
PXE-DCM+: PixiePlus - Single-Gang IR/RS2323 control system for AV
systems
PixiePlus System










8-button Display Control Module
Single-gang decora form factor
Learns IR codes from almost any remote
Unique modular design allows for control
of Power, Source, Volume and more
Elegant backlit LEDs in a variety of colors
A single button may be programmed with
multiple remote codes
Learns IR codes from almost any remote
using a paper clip
Decora faceplate available in: white, ivory,
grey, and black


PXE-BIK50: PixiePlus Basic Install Kit
PXE-PL-BL: PixiePlus Tabletop Enclosure Black
PXE-RACK: PixiePlus 3RU Rack Mount











Robust IR learning with 16 macros or
round-robin commands per button
Security enable/disable feature allows the
panel to be configured with a security
entrance code to prevent unauthorized
use
Configurable inactivity shutdown timer
Up to 8 input sources
All blanks and labeling legend included
Easy to configure, customize, and use





Four IR out
Ability to expand the (NRC) Networked
Room Controller by daisy chaining up to
15 control pucks using CAT5 cabling.
Small form factor, allowing for remote
installation anywhere







Connects via IR interface and allows for
RS232 control
Eliminates the need to remove the controller from the wall to program
Connects to a PC via USB and contains an
application for more complex configurations, including specifying RS232 strings
Ability to clone commands to other
PixiePlus controllers






PXE-EMIT-232/IR: RS232 and IR Emitter
PXE-EMIT-REL2: 2-Relay Output Emitter
PXE-DCM-RTC: Real Time Clock Module
PXE-DCM-CAT5-ADAPTOR: Phoenix-toCAT5 Adaptor
PXE-DCM-EMIT-CAT5-232/IR: RS232 and
IR Emitter with CAT5 Jack
Alternate 2 and 4 source buttons available
Rack Mount Kit to mount the PXEDCM+
Black Finish
3RU height
PX2-PUC-232/IR: NRC Control Puck (1 RS232 and 1 IR)


One bidirectional RS-232 control port, one
infrared (IR) control port, four low-voltage
relays for screens or lifts, and two general
purpose sense ports for security and theft
detection
Includes adapters for common pinouts of
9-pn or 15-pin D-Sub S-232 control ports
on most modern display devices
Configured through an AJAX-powered web
interface
Expandable for virtually any room configuration and any budget

One RS-232 port and one IR port
Ability to expand the (NRC) Networked
Room Controller by daisy chaining up to
15 control pucks using CAT5 cabling.
Small form factor, allowing for remote
installation anywhere
PX2-PUC-MOTVOL-CTL-A and PX2-PUC-MOTVOL-CTL-L: Motorized
Volume Control Puck - Audio and Linear for us with NRC

Four low-voltage relays
Ability to expand the (NRC) Networked
Room Controller by daisy chaining up to
15 control pucks using CAT5 cabling.
Small form factor, allowing for remote
installation anywhere
PX2-PL-WH: PixiePro Tabeltop Enclosure White
PXE-EMIT: 6 Volt IR Emitter for the
PixiePro and PixiePlus. 3 Wire format use
18 through 22 2C shielded cable. Connects to the PCE-DCM+. This is for use
with IR only on the PixiePor. The PixiePlus
uses the PXE-EMIT-232/IR type emitter
PXE-EMIT-HOOD: Used with PXE-EMIT
and PXE-EMIT-232/IR as a protective
covering hood to cover and secure IR
emitter
PX2-SPBUS-2WAY: PixiePro NRC BUS
Splitter 2-Way. Increases the amount of
controlled equipment

PixiePlus Accessories: Accessories for the Pixie Plus Control Module
PX2-PUC-REL-4: NRC Control Puck (4 Relay)
PixiePro Family Accessories: PixiePro IR Emitter / IR Emitter Hood /
Splitter




50 ft 22 AWG 3 conductor plenum prestripped cable
1 single gang Decora Plate, 1 surface
mount box
1 single gang mounting bracket
Quick install kit for labor saving and
efficiency
PX2-NRC-1142: PixiePro (NRC) Networked Room Controller (1 RS232,
4 Relay, 2 Input)
PX2-PUC-IR-4: NRC Control Puck (4 IR)



Tabletop standalone enclosure
For PXE-DCM+ Panel Single Gang
Stylish Black Acrylic in a pleasing format
Angles for presentation and ease of
access
PX2-MP
-IR: Pixie Pro Control Module


PXE-PGM-TOOL: PixiePlus Programming Wand
PixiePlus Device Control Module 8-Buttons
Simple, standardized control interface for
AV devices
White Background with Amber or Green
backlit buttons
Wall mounted Single Gang Decora style
faceplate
PXE-MOTVOL-CTL-A; PXE-MOTVOL-CTL-L : PixiePlus Motorized Volume Control - Audio and Linear
 Passive 10K ohm stereo motorized potentiometer (Audio Taper)
 Powered from the PXE-DCM+
 Directly attenuates unbalanced stereo line
level signals
 For controlling Audio Amplifiers without
IR/RS232 control
 Can be placed in an audio chain between
a mixer/switcher/preamp and an amplifier
 Linear version allows the PixiePLus to
control an amplifier that otherwise has no
control.




PixiePro Family
PXE-DCM+Amber; PXE-DCM+Green: PixiePlus 8 Button Control
Module - Amber and Green



10K Ohm stereo motorized potentiometer
(Audio Taper)
Powered from the PX2-NRC-1142
Directly attenuates unbalanced stereo line
level signals
For controlling Audio Amplifiers without
IR/RS232 control
PX2-RACK and PX2-RACK-MOD: Rack Mount Kits
Tabletop standalone enclosure
For PX2-MP-IR Panel Four Gang size
Stylish White Acrylic in a pleasing format
Angled for presentation and ease of
access


PX2-RACK: Rack Mount Kit for the PixiePro
Line. 3 Rack Unit height. Black.
PX2-RACK-MOD: Rack Mount Kit for the
SP2-SMCHAS. Includes Cut outs for 2 Mini
Modules/ 3 Rack Unit height. Black.
SP Controls core control (PixiePlus System and PixiePro Family) and audio products (AmpLinc Hub and Amp/Puck) are made in the USA.
800.530.8998 | www.LibAV.com | SPECIFICATIONS & IMAGES SUBJECT TO CHANGE | IMAGES NOT TO SCALE | L0233
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
|
800.530.8998
|
www.LibAV.com
39
SP CONTROLS
SP CONTROLS PRODUCT OFFERING AT-A-GLANCE
SP2-SMCHAS: Mini SmartPanel Control System




SmartPanel Systems

SP3-TCM+: Transport Control Module (for DVD Players, VCRs, etc.)
Small Profile Chassis for ease of mounting
and location
Simple intuitive Projector/Display Control
No Programming needed, simply configure
Control Audio/Video, contact closure for
screens and lifts
Available in: Black, White, Blue, Gold,
Red, Grey (added charge)


Audio & AmpLinc System







Mounting System


SP2-SMWE-B; SP3-SMPL-B; SP3-TCM+STD-BL: SmartPanel Enclosures



SP2-SMCHAS Wood Enclosure
SP2-SMCHAS Poly Enclosure
SP3-TCM+STD-BL: Transport Control
Module Tabletop Enclosure
For desktop or tabletop mounting
SP2-ETH-M100: Lucent M100 Series CAT5 Jack
SP2-SMMR: Mud Ring For SP2-SMCHAS
SP2-SMAP-BL: SmartPanel Mini 5G Adapter
Plate
AmpLinc Hub-90W: 90W Speaker Distribution Hub for AmpLinc Amp
10









SmartDrawer for SP2-SMCHAS mounting
Under Desk or under Table mounting of
AV Controls
Black finish, low profile
Can accommodate the SP3-AFVP+ Preamp
Includes ports for four Mini Modules















Remote Amplifier device for 4/8
Ohm speakers
Control and Power with Category
Cable
Tap power from 0.3~10 watts
1 to 60 units can be daisy chained
For use with the AmpLinc Hub and
AmpLinc Hub-90W
SP-ICE5: 4” Aimable Enclosed Ceiling Speaker (Single)





4” Co-Axial Speaker
160hms nominal impedance
100 Hz - 20 KHz frequency range
90dB @ 1w/1m sensitivity
25 watts max power handling
Mini Modules: Patch Modules for the SLB-SBOX+









Wall mounted SmartBox enclosure with
flip down tray black
Equipment space for Blu-Ray/DVD player
Flat surface for laptop or other portable
media source
SP2-SMCHAS mounting feature for control
integration
Amplifier mounting and patching module
features built in
Available white, black or custom color
SLB-SBOX 100W-WH; SLB-SBOX 70V-WH; SLB-SBOX 50W-WH: SmartBox+ Speaker Amplifiers


5.25” 2-way speaker system
90 dB @ 1w/m frequency response
200 Hz - 20 KHz frequency range
8 ohms impedance
250 watts max power handling
SLB-Box+: SmartBox+ Flip-Down Equipment/Control Enclosure

AmpLinc Amp10: AmpLinc Amp10 Remote Speaker Control Puck
Audio Distribution hub over Category
Cable
90 watts permits 8 10W AmpLINC PUCS
Small and scalable
3.5TRS or 2 RCA input and 4 RJ45 output
SP-BS5IN-W: 5.25” 2-way Bookshelf Speaker Pair
SLB-1050B: Slide-Out Drawer for SP2-SMCHAS





Secure and vented, locking storage box for
AV & IT equipment
Removable tray where equipment is mounted that slides into the main frame of the box
Removable lid with key lock and now screws
Flexible mounting options for wall, ceiling, or
projector pole mount
Two cable exit holes for standard voltage
Optional cable cover and adjustable pole
mount



SP2-CSB: Replacement SmartPanel Buttons; Full
Replacement set of selection buttons
SP2-BSB: Replacement SmartPanel Buttons; set
of 4
Audio Follow Video preamp addition for
SmartPanel or NRC
5 Video CH with 5 L/R unbalanced Audio
Channels
Fully adjustable gain (10dB), bass, and
treble
Superior audio over built in projector
speakers
Compatible with other OEM RS-232
control systems
SLB-SBOX II: SmartBox II Secure Equipment Enclosure






Audio Distribution hub over Category
Cable
60 watts from 2 to 60 amplifier pucks
Small and scalable
3.5TRS or 2 RCA input and 4 RJ45 output



SP2-SMCHAS: Rack Mount Kit
SP2-SMCHAS: 2 Ru Rack Mount
Standard 19” Rack size
SP3-AFVP+: Audio Follow Video Preamplifier Plus



TCM for extending the SmartPanel Control
System
Standard and extended control features for
sources
Can learn IR codes direct or clone from
another TCM
Also available in Grey
SmartPanel Accessories : Accessories for SmartPanel
AmpLinc Hub: 65W Speaker Distribution Hub for AmpLinc Amp 10


Twisted Pair Extender Audio over Category Cable
Extend connection between SmartPanel
and SP3-AFVP+
Extend up to 50 feet with standard
Category Cable
SP2-RACKSM; SP2-RACKSM-MOD : Rack Mount Kits





TCM for extending the SmartPanel Control
System
Standard and extended control features for
sources
Can learn IR codes direct or clone from another
TCM
Control up to 5 devices
SP2-CSB; SP2-BSB: SmartPanel Button Sets
SP2-AFVP-EXT: AFVP Extender


SP3-TCM+1GANG-BL: Standalone Transport Control Module (Black)
AUXILLIARY Audio Enable Switch
Blank
Escutcheon and Dual Panduit
HDMI
RS232
S-Video Pass-thru
VGA and VGA out
Video on BNC and on RCA
Keylock
SmartBox Accessories: Accessories for SmartBox+
Designed to fit into the SLB-BOX+ enclosures
Easy match to the SP3-AFVP+ audio follow
video preamp
120V convenience AC Outlet for Laptop
power included
SLB-SBOX 100W-WH: 100 Watt Stereo
Audio Amp; 100 Watts per channel, for
use with 4 or 8 ohm speakers
SLB-SBOX 70V-WH: 100 Watt 70V Mono
Audio Amp; 100 Watt 70 Volt Single Mono
Channel
SLB-SBOX 50W-WH: 50W SmartBox Amp
Available in black






SLB-SBOX 1GANG - Pixie Face Cover
SLB-SBOX FACE - Blank Face Cover
SLB-SBOX MINIFACE - Modular Face
Cover
SLB-SBOX 1GANG-WH - PixiePlus
Face Cover. Also available in black.
SLB-SBOX PX2 - PixiePro Face Cover
SLB-SBOX PX2-BL-RM: Reverse
mount for added security. (Black
only.)
SP Controls core control (PixiePlus System and PixiePro Family) and audio products (AmpLinc Hub and Amp/Puck) are made in the USA.
40
800.530.8998 | www.LibAV.com | SPECIFICATIONS & IMAGES SUBJECT TO CHANGE | IMAGES NOT TO SCALE | L0233
800.530.8998
|
www.LibAV.com
|
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
ACCESSORIES
FLEXBOX-WH
FLEXIBLE A/V SOLUTIONS ENCLOSURE SYSTEM
Patent pending
removable tray for
easy assembly and
maintenance
UL 2043 compliant for Plenum installations.
FLEXBOX Benefits:
FLEXBOX Features:
• The ability to custom brand this
enclosure solution
The equipment enclosure has a sliding slotted shelf that requires no hardware
or screws to secure it. The box can be populated with a number of devices
on the slotted shelf with room for miscellaneous cables and power supplies
conveniently tucked away. Equipment can be mounted using cable ties, velcro
or via self-tapping screws into the sliding shelf. Since the shelf is secure when
in place, the enclosure can be mounted upside down allowing for easy service
access to equipment once installed.
• Ability to exchange parts or customize our
solution to meet your customers specific
needs, giving you an advantage over off
the shelf solutions
• Allows to write custom specifications
for these solutions
• Lightweight construction
• Our solutions give you the flexibility
of providing systems with a teacher/
microphone option or without
• Vented design construction uses natural convection for cooling
• All systems can be implemented into LIS
(Liberty Inventory Services). We can have
safety stock in LIS for field swappable
systems as a backup
• Custom kitting to include enclosure with pre-installed equipment specifically
designed with custom part number to create unique specification and
protect your intellectual property
• Install flexibility: above ceiling without relying on T-Bar placement; below
the ceiling; pole mounted; or wall mounted
• Systems can be pre-assembled for large deployments
• If you have deployments in other
cities, we will be able to leverage
WESCO facilities for warehousing
accommodations if needed
• Systems can be pre-configured for plug and play installations
• Secure key lock removable lid provides easy access to internal equipment
PRE-LOADED FLEXBOX OPTION PACKAGE
DESCRIPTION/LOCATION
MANUFACTURER
PART NUMBER
QUANTITY
Control processor with Doceri™ software support
SP Controls
PX2-NRC-1142
1
Wall-mount control panel
SP Controls
PX2-MP-IR
1
Internal wiring
SP Controls
PX2-PUC-232/IR
2
Mounting hardware
SP Controls
SLB-SBOX2
1
Local source wall plate
Broadata
LBC-H/V-T-WP
1
HDBaseT receiver
Broadata
LBC-HDBT-R-LITE
1
Digital switcher
Digitalinx
DL-S41
1
Audio amplifier
Intelix
AUD-220
1
Internal wiring
Liberty
E-3.5SM-M-3
1
Ceiling speakers
Atlas
FAP42T
1
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
|
800.530.8998
|
www.LibAV.com
41
ACCESSORIES
BYOD-HUB-UT
BYOD CONNECTION HUB - 6 INPUT TO HDMI AUTO-SWITCHER AND CONVERTER
The Digitalinx BYOD-PUCK is a multiformat video converter to connect
mobile devices with the following outputs: HDMI, mini DisplayPort,
micro USB, Lightning, and USB type C.
Video Compliance
HDMI 1.4 and HDCP 1.4
Embedded Audio
Up to PCM 8 channel, Dolby Digital TrueHD, and
DTS-HD Master Audio
CHASSIS AND ENVIRONMENTAL
TECH SPECS
INPUT/OUTPUT CONNECTIONS
Construction
Black ABS
Dimensions (H x W x D)
25 mm x 100 mm x 100 mm (0.98 in x 3.94 in x
3.94 in)
Input Cable Length
300 mm (11.81 in)
Operating Temperature
0° to +40° C (+32° to +104° F)
Operating Humidity
20% to 90%, Non-condensing
Storage Temperature
-10° to +60° C (+14° to +140° F)
Storage Humidity
20% to 90%, Non-condensing
Input Cables
One (1) HDMI Type A Plug, One (1) Micro USB
Type B Plug, Two (2) USB Type C Plugs (MHL and
Mac), One (1) Mini DisplayPort Plug,
One (1) Lightning Plug
POWER AND REGULATORY
HDMI Output
One (1) HDMI Type A Receptacle
Power Input
12V DC 2A
Security
One (1) Kensington Lock Slot
Power Output
Power
One (1) 5.5 mm OD, 2.6 mm ID Threaded Barrel
5V DC 2.1A (Lightning, micro USB, and USB Type
C)
Power Consumption
18 watts when powering mobile device
ESD Protection
15kV air, 8kV contact
Regulatory
FCC, CE, RoHS
SUPPORTED AUDIO, VIDEO AND CONTROL
Input Video Resolutions
HDMI: Up to UHD/30
Micro USB: Up to 1080p/30 Lightning:
Up to 1080p/60
USB Type C (MHL): Up to 1080p/60 USB
Type C (Mac): Up to UHD/30 Mini Display
Port: Up to UHD/30
Output Video Resolutions
SMPTE: 480i, 480p, 576i, 576p, 720p, 1080i,
1080p, UHD/30 VESA: Resolutions up to
1920x1200. Color Depth: 24, 30, 36, 48bit
DON'T BE
A LOSER!
2 years
Diagnostic Indicators
Power
Included Accessories: Installation Guide, Power Supply,
DL-CL
Unbreakable
stainless steel
security ring
BLACK clamp assembly
& foam inserts to
securely fit any sized
HDMI cable
ARDPHD
Display Port male
to HDMI female
in-line adapter
ARDVHD
DVI-D single
link male to
HDMI A female
CREATE YOUR OWN CUSTOMIZED
42
Warranty
dl-ar
Patent Pending
UNIVERSAL HDMI®
ADAPTER RING
OTHER
ARMCHD
Micro-HDMI D male
to HDMI female
in-line adapter
Mini-HDMI C male
to HDMI female
in-line adapter
Provided by
800.530.8998
ARMDHD
|
www.LibAV.com
|
ARMDPHD
Mini-Display
Port male to
HDMI female
in-line adapter
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
ACCESSORIES
TRB-2V1AD / TSPB-2V1AD / TDPB-2V1AD
ROUND TABLE BOX AV+N W/LID BLK
TECH SPECS
PORTS
1 HDMI connector, 1 15-pin HD connector, 1 3.5mm mini
jack, 1 RJ-45 connector
OPERATING TEMPERATURE
0° to +40°C (32° to 104°F)
STORAGE TEMPERATURE
-40° to +70°C (-49° to 158°F)
HUMIDITY
10% to 90%, RHL non-condensing
POWER SOURCE
AC power limits: 115V AC, 50/60Hz, 5A Max
FUSE RATING
T 6.3A 250V
DIMENSIONS
10.5cm x 16cm (4.1" x 6.3") Diameter, H
WEIGHT
0.85kg (1.9lbs) approx.
1.2kg (2.6lbs) approx. with mounting brackets
INCLUDED ACCESSORIES
TRB-2V1AD
Six self-locking ties
TECH SPECS
PORTS
1 HDMI connector, 1 Ethernet RJ-45 connector, 1 15-pin
HD connector, 1 3.5mm mini jack
POWER SOURCE
100-240V AC, 50/60Hz, 5A Maximum 5A per power outlet
FUSE RATING
T 6.3A 250V
OPERATING
TEMPERATURE RANGE
+5 to +45 Deg. Centigrade
OPERATING
HUMIDITY RANGE
10 to 90% RHL, non-condensing
STORAGE
TEMPERATURE RANGE
-20 to +70Deg. C.
STORAGE HUMIDITY RANGE 5 to 95% RHL, non-condensing
TSPB-2V1AD
DIMENSIONS
Including the outer rim: 14.5cm x 13.2cm x 17.3cm (5.71"
x 5.2" x 6.81") W, D, H , Without the outer rim: 13.3cm x
12.0cm x 17.3cm (5.24" x 4.72" x 6.81") W, D, H
WEIGHT
0.85kg (1.87lbs) approx. , 1.2kg (2.65lbs) approx. with
mounting brackets 1.4 kg (3.1lbs) approx. packed
product
ACCESSORIES
Cut out metal template
OPTIONS
Power socket kits, power cord
TECH SPECS
TDPB-2V1AD
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
|
PORTS
2 HDMI connector, 2 Ethernet RJ-45 connector,
2 15-pin HD connector, 2 3.5mm mini jack
POWER SOURCE
AC power limits: 100-125V AC, 50/60Hz,
5A Maximum 5A per power outlet
FUSE RATING
T 6.3A 250V
OPERATING TEMPERATURE
0° to +40°C (32° to 104°F)
STORAGE TEMPERATURE
-40° to +70°C (-40° to 158°F)
HUMIDITY
10% to 90%, RHL non-condensing
DIMENSIONS
Including the outer rim: 28.5cm x 14.0cm x 16.5cm
(11.2" x 5.5" x 6.5") W, D, H . Without the outer rim:
26.5cm x 12.0cm x 16.0 cm (10.4" x 4.7" x 6.3") W, D, H
WEIGHT
1.64kg (3.6lbs) approx., 1.88kg (4.1lbs) approx. with
mounting clamps, 2.26kg (5lbs) approx. packed product
ACCESSORIES
Cut out metal template
OPTIONS
Power socket kits, power cord
800.530.8998
|
www.LibAV.com
43
CABLES: HDMI MOLDED
HDPMM** HDMI PREMIUM 18.0G
HDMI PREMIUM® CERTIFIED CABLE ASSEMBLY
key features
• H DMI Premium® full 18G Certified
• Full ATC Certification
• H igh retention HDMI plugs
• U L/CSA listed for in-wall use
• C onvenient cable lengths
Liberty’s HDPMM Series are our full ATC certified HDMI Premium® rated cables. The newest HDMI cable specification is for 18G
applications. [email protected] with full Chroma sampling 4:4:4 and the newest High Dynamic Range (HDR) requirements. This line of
HDMI® cables supports every single HDMI requirements for cables and signal transport. These are completely traceable per the
new HDMI requirements for the Premium certification.
The HDPMM series is robustly constructed with tinned annealed copper conductors on the shielded TMDS pairs. The overall
cable is dual shielded with a full coverage foil shield and an 85% coverage braided shield. Unlike many cables on the market, the
connectors feature full shielding over the solder joints instead of drain wire under a pre-mold. These cables are fully shielded from
connector shroud to connector shroud. All contact surfaces are gold plated for conductivity, durability, and resistance to tarnish.
The high retention connectors increase the standard HDMI holding force up to 10 lbs. The jacketing is non-glossy extra flexible
PVC for more flexibility in bending and routing in Residential and light commercial applications.
Lengths from 15 to 24 feet long are passive cables. There are no equalization chipsets and directional requirements on
these lengths. These HDMI Premium® cables feature UL ratings on the bulk cable for CMG and Canadian CMG FT4, this is
permissible for concealed installations per the requirements of the National Electric Code®. The product is Compliant to the
requirements of the EU RoHS-2 2011/65/EU standard.
TECH SPECS
INPUT/OUTPUT CONNECTIONS
HDMI
Male HDMI Type A connector
HDMI SUPPORTED VIDEO, AUDIO AND ETHERNET
HDMI Maximum Video
Compatibility
[email protected] 4:4:4 up to 3m, HDR Support
Video Compliance
HDMI, HDCP, and CEC (Consumer Electronics
Control)
Embedded Audio
Up to 32 Audio Channels and up to 1536 KHz
Audio Sampling
Minimum Bandwidth
18.0 Gbps
Ethernet
100 Mbps
20.0x41x11.2mm
Jacket Material
Flexible Flame rated PVC with a matte black
finish
Maximum Tensile Load
44Lbs | 20Kg
Available Cable Lengths
15, 20, and 24 feet
ENVIRONMENTAL REQUIREMENTS
Operating Temperature
0° to +75° C (+32° to +167° F)
Operating Humidity
20% to 85%, Non-condensing
Storage Temperature
-20° to +80° C (0° to +176° F)
POWER AND REGULATORY
CABLE CONSTRUCTION
HDMI Connector Features
HDMI “A” Male with up to 10 lbs high
retention feature, gold plated
HDMI Molded Hood Construction
Copper Foil Shielded Pre-mold with PVC over
mold. Over mold is two phase black with a
gray nose
44
HDMI Molded Hood Dimensions
800.530.8998
|
Regulatory
NEC CMG, CEC CMG FT4, EU RoHS-2 2011/65/
EU Compliant
HDMI®
HDMI Premium® Certified
Check the website for specific product physical specifications
www.LibAV.com
|
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
CABLES: HDMI MOLDED
HDMI SOLUTIONS
• ECONOMY & PREMIUM LEVELS
• HIGH SPEED HDMI®
• COPPER & FIBER VERSIONS
• PLENUM, NON-PLENUM & AWM RATED
• WIDE SELECTION
• UL, CSA & ROHS
• HIGH QUALITY PRODUCT
• COMPETITIVE PRICING
HDPMM SERIES PREMIUM HIGH SPEED HDMI CABLES WITH ETHERNET
• Premium High Speed HDMI Cables with Ethernet
• Full 18 Gig [email protected] and HDR Certified
by HDMI ATC
• Supports Ethernet, ARC, CEC, and all
HDMI Audio formats
E2-HDSEM-M SERIES LIBERTY E2 HIGH SPEED HDMI WITH ETHERNET
• 28 & 26 AWG TMDS pairs
• Low profile molded head
• High retention plugs up to 12 lbs
• C L2 & CMG FT4 rated, RoHS compliant
• 5m & up feature RedMere® Chipsets
M2-HDSEM-M SERIES LIBERTY M2 HIGH SPEED HDMI WITH ETHERNET
• 30 AWG copper TMDS pairs
• Super low profile molded heads
• High retention plugs up to 12 lbs
• AWM rated, RoHS compliant
• H DMI® “A” male to “A” male connectivity
• U ltra small flexible diameter cable 3.6mm in diameter
• Flexible polyvinyl chloride jacket
• AWM rated, RoHS compliant
Z100HDE SERIES LIBERTY HIGH SPEED HDMI WITH ETHERNET
• 28 AWG copper TMDS pairs
• Economy public mold design
• A WM rated, RoHS compliant
• 10.2 Gbps, 4k video, all HDMI® audio formats
P-HDM-M SERIES LIBERTY PLENUM HDMI WITH ETHERNET
• 24 AWG copper TMDS pairs
• Super low profile molded heads
• CMP FT6 rated, RoHS compliant
• 8m high speed HDMI® with Ethernet
• 10 & 12m passive standard HDMI®
|
IMAGES NOT TO SCALE
|
800.530.8998
|
BEST
• All lengths rated for 18.0 Gbps
• NEC CM, CEC CMG FT4, RoHS/REACH Compliant
• Full traceable HDMI Premium serialized
• Lengths 3, 6, 10, 15, 20 and 24 feet
COMMERCIAL GRADE
BETTER
PERFECT FOR PATCHING CABLES IN RACKS
BETTER
• 5m & longer are directional
• 10.2 Gbps, 4k video, all HDMI® audio formats
• Supports CEC, audio return & Ethernet
• Lengths from ½ to 20m
• Black with blue molded heads
• U p to 8ft, 10.2 Gbps, up to 15ft 5.0 Gbps
• Supports CEC, audio return & Ethernet
• Available in 1,2,3,4,5,6,8,10,12 & 15ft
• U ltra flexible black with black molded heads
E-MHDM-M SERIES LIBERTY HIGH SPEED MICRO HEAD HDMI WITH ETHERNET
SPECIFICATIONS SUBJECT TO CHANGE
COMMERCIAL AND RESIDENTIAL
HDMI CONNECTIVITY
MAXIMUM FLEXIBILITY PERFORMANCE
GOOD
IDEAL FOR BUDGET CONSCIOUS INSTALLATIONS
VALUE
PLENUM RATED COMMERCIAL GRADE
GOOD
• A TC certified HDMI® high speed with Ethernet
• 10.2 Gbps / 4k × 2k / 3D / CEC
• Lengths 2m & longer are directional
• 4m length does not support Ethernet
• Supports CEC, audio return & Ethernet
• Available in 3, 6, 10, 15 & 25ft lengths
• Q uantity discounts
• B lack
• 15m & longer feature RedMere® Chipsets
• 15m & longer are directional
• Supports 1080P, audio return (8-12m CEC)
• Available in 8,10,12, 15 & 23m
• Black with black molded heads
www.LibAV.com
45
CABLES: HDMI MOLDED
HDMI SOLUTIONS
DL-HFC SERIES DIGITALINX PLENUM RATED OPTIC HDMI WITH DETACHABLE HEADS
•
•
•
•
PF-HDM HYBRID HIGH SPEED HDMI AOC (ACTIVE OPTICAL CABLE)
• HDMI "A" male to male connectivity
• Polymer Optical Fiber (POF) for better flexibility
• U ltra-Small diameter cable with reduced
sized HDMI heads
DL-HDM-M
18G ACTIVE OPTICAL HDMI (NO EXTERNAL POWER REQUIRED)
Opto electronics delivers 18G
• Uwithout
nique patented
power
• H DMI "A" to HDMI "A" Male connectivity
• Small Flexible bulk cable
HD-700 SERIES PPC® LOCKING HIGH SPEED HDMI WITH AUDIO RETURN
•
•
•
EC CMP-OF, CEC FT6, HDCP 2.2, RoHS compliant
N
Lengths: 25, 35, 50 & 75ft
HDMI High Speed, 10.2Gpbs, [email protected] 4:2:0
3D, all audio
PLENUM HIGH‐SPEED HDMI
BEST
MAXIMUM LOCKING PERFORMANCE PACKAGE
BEST
• D raws power from pin 18 of the source/display
HDMI port
• H DMI High Speed 10.2Gbps [email protected] 3D
all Audio formats
• Supports [email protected] with 4:2:0 Chroma Sampling
• Real Glass, no Plastic Optical Fiber
• Built to be installed, full strain relief for head pull
• Full HDMI 2.0b 18G, HDR, 4K60Hz 4:4:4, all Audio
LOCKING PERFORMANCE PACKAGE
• 28 AWG copper TMDS pairs
• True Locking HDMI® feature up to 25lbs+
• CL2, CMG FT4, RoHS compliant
• 10.2 Gbps, 4K video, all HDMI® audio formats
• Supports CEC, audio return & Ethernet
• A vailable in 2,4,8,16,25,35 & 50ft lengths
• 16ft & up are active & directional
• Black with gun metal metallic hoods
HD-600 SERIES PPC® HIGH RETENTION HIGH SPEED HDMI WITH ETHERNET
• 28 AWG copper TMDS pairs
• High Retention plugs up to 12lbs
• CL2, CMG FT4, RoHS compliant
• 10.2 Gbps, 4K video, all HDMI® audio formats
• Fiber Optic Ribbon Cables
• Detachable HDMI® TX and RX modules
• Handles up to 60lbs of pull force
• OFNP FT6 rated, RoHS Compliant
• M iniature molded micro USB format (not USB)
GOOD
PLENUM RATED FIBER FEATURING DETACHABLE HEADS
BEST
• 21.0 Gbps, [email protected] ready, all HDMI® audio
• Supports CEC, audio return
• Lengths from 35 to 1000ft
• Requires powered receptacles on both sides
• Black cable and black ABS ends & modules
Detachable Fiber
Optic HDMI Connector
(USB power required
on the receiver side of
the installation)
Detachable HDMI
connector makes
pre-wiring of the fiber
optic cable as easy as
plug & play
Perfect for HD custom
cable lengths in the field!
CRIMP & CUTTING TOOL
DL-HDMCBL
46
TERMINATE IN 5 MINUTES!
• Locking HDMI connector technology increases retention up to 400%
• Customize your HD cable lengths to professionally dress racks & minimize excess cable
• Supports HDMI with Ethernet, CEC and bi-directional audio formats
• Send 1080p video up to 55ft with optional extender
RIBBON CABLE
800.530.8998
DL-HDMHT
|
BETTER
IDEAL FOR BUDGET CONSCIOUS INSTALLATIONS
• Supports CEC, audio return & Ethernet
• Available in 3, 6 & 12ft lengths
• Thumb latch and release feature
• Black with black ABS hoods
DFO-1000P CELERITY PLENUM RATED FIBER OPTIC HDMI LONG DISTANCE CABLE
HD TERMINATION
BEST
HYBRID COPPER/FIBER
Plenum rated cable for all installations
Ultra-small diameter cable
Detachable HDMI TX & RX units from main body
No external power needed, uses equipment power
www.LibAV.com
|
CONNECTORS & SHELLS
HD TERMINATION
OPTIONAL EXTENDER
DL-HDMCPK
SPECIFICATIONS SUBJECT TO CHANGE
WATCH IT NOW!
74-035-01
|
IMAGES NOT TO SCALE
CABLES: HDMI AOC
DL-HDM-M *NEW* HDMI AOC RISER 18.0G
18G 4K60 4:4:4
HDMI Maximum Performance AOC Hybrid Cable
TECH SPECS
INPUT/OUTPUT CONNECTIONS
HDMI
Male HDMI Type A connector
HDMI SUPPORTED VIDEO,
AUDIO AND ETHERNET
HDMI Maximum
Video Compatibility
Liberty’s DL-HDM-M Series are
Active Optical Cables (AOC) featuring
a unique hybrid construction and
construction the industry has been
waiting for. The cable strain relief is
anchored into the connector housings
to prevent inadvertent damage so
common in other AOC cables.
key features
• True 18G Fiber Optic Performance
• N o external power required
• D esigned for pulling
• U L/CSA listed for in-wall use
• C onvenient cable lengths
Jacket Material
Flexible Flame rated PVC with a
black finish
Cable Construction
4 Multimode OM2 equivalent
fibers with 7 copper conductors
Overall Cable Size
0.142” | 3.6mm
Minimum Bend Radius 1.42” | 36mm
[email protected] 4:4:4 up to 100m,
HDR Support
Maximum Tensile Load 100Lbs | 45Kg
Video Compliance
HDMI, HDCP, and CEC (Consumer
Electronics Control)
Available Cable
Lengths
Embedded Audio
Up to 32 Audio Channels and up
to 1536 KHz Audio Sampling
ENVIRONMENTAL REQUIREMENTS
8, 10, 15, 23, 30, 50, 60, and 100
meters
Minimum Bandwidth 18.0 Gbps
Operating
Temperature
0° to +60° C (+32° to +140° F)
Ethernet
Operating Humidity
20% to 85%, Non-condensing
Not supported
CABLE CONSTRUCTION
Storage Temperature -20° to +80° C (0° to +176° F)
HDMI Connector
Features
HDMI “A” Male
POWER AND REGULATORY
HDMI Hood
Construction
Metal Shell for extreme
durability and proper cable
strain relief
HDMI Molded Hood
Dimensions
19.6x40x10.0mm with a 14mm
strain relief
NEC CMR-OF, CEC CMG FT4, EU
RoHS-2 2011/65/EU Compliant
Regulatory
COMING SOON!
DL-PHDM-M Plenum and
DL-ZHDM-M Palogen Free
PF-HDM-M HDMI AOC PLENUM 10.2G
PLENUM HIGH-SPEED HDMI® ACTIVE OPTICAL CABLE
TECH SPECS
Minimum Bend Radius 5 mm
INPUT/OUTPUT CONNECTIONS
Male HDMI Type A connector
HDMI
SUPPORTED AUDIO AND VIDEO
key features
• H DMI "A" male to male connectivity
• P olymer Optical Fiber (POF) for
better flexibility
•
Ultra-Small diameter cable with
reduced sized HDMI heads
• D raws power from pin 18 of the
source/display HDMI port
3D all Audio formats
• S upports [email protected] with 4:2:0 Chroma Sampling
• Does not support Ethernet or Audio Return
• Lengths: 10, 15, 20, 23, and 30 meters
• N EC/CEC rated CMP-OF Plenum, RoHS-2
Compliant
SPECIFICATIONS SUBJECT TO CHANGE
|
ENVIRONMENTAL REQUIREMENTS
Maximum Video
Compatibility
[email protected] 4:4:4 Chroma or
[email protected] 4:2:0 Chroma
Operating
Temperature
0° to +50° C (+32° to +122° F)
Video Compliance
HDMI, HDCP, and CEC
(Consumer Electronics Control)
Operating Humidity
20% to 85%, Non-condensing
Embedded Audio
Storage Temperature
-30° to +50° C (-22° to +122° F)
Storage Humidity
20% to 85%, Non-condensing
Input DDC Signal
Up to PCM 8 channel, Dolby
Digital TrueHD, and DTS-HD
Master Audio
5.0 volts p-p (TTL)
Input Video Signal
0.5 to 1.0 volts p-p
Power Supply
Via HDMI pin 18
Maximum Bandwidth
10.2 Gbps
Power Consumption
0.07 watts
Regulatory
NEC® rated CMP-OF, CEC rated
CMP, RoHS Compliant
CABLE CONSTRUCTION
• H DMI High Speed 10.2Gbps [email protected]
Maximum Tensile Load 20 kg (44 lbs.)
HDMI Hood Material
Molded ABS
HDMI Hood
Dimensions
9.50 mm x 18.7 mm x 26.8 mm
(0.373 in. x 0.734 in. x 1.06 in.)
Fiber Jacket Material
Plenum Rated PVC
Cable Construction
Hybrid POF (Plastic Optical
Fiber) and Copper
Overall Cable
Diameter
5 mm
IMAGES NOT TO SCALE
|
800.530.8998
|
POWER AND REGULATORY
OTHER
Warranty
www.LibAV.com
2 years
47
FIBER OPTIC CABLE SOLUTIONS
FIBER OPTIC SOLUTIONS
Stronger, Safer
and Faster than
standard fiber
optic cable!
· 10,000x’s THE FLEX LIFE OF STANDARD FIBER!
Extremely high mechanical fatigue rating. This makes SSF®
Fiber 10,000x’s less susceptible to breaking due to bending.
SSF® Fiber has a pull tension that is 2.5 – 4x’s that of UTP!
· NEARLY IMPOSSIBLE TO GENERATE GLASS SLIVERS
DURING STANDARD USE! SSF® Fiber is completely safe to
handle & will not present the inherent safety concerns that
conventional glass fiber brings.
· 33% LABOR SAVINGS USING OUR FIELD TERMINABLE
SC PLUGS. The termination process for SSF® Fiber is very
simple; it does not require a trained / certified fiber technician.
· THE PATENTED POLYMER COATING ON SSF® FIBER.
Guarantees no contamination reaches the underlying glass.
Moisture, dirt & even human skin oils are kept from the
signal carrying core & cladding by the proprietary coating.
This feature increases the lifetime of the fiber well above
& beyond standard fiber constructions.
· MICRO-DISTRIBUTION SSF® FIBER IS THE ULTIMATE IN
SMALL DIAMETER FIBER CABLE. Have a small conduit?
Pull many more fibers than standard construction tight
buffer fiber solutions.
WWW.LibAV.COM | 800.530.8998
48
800.530.8998
|
www.LibAV.com
|
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
FIBER OPTIC CABLE SOLUTIONS
SSF CABLE SOLUTIONS
®
No stripping required | Incredible bend longevity assured for 10,000x’s longer lifetime than normal glass fibers
Cleerline SSF is a leap ahead for field installation! Increasing the speed, safety & efficiency of fiber
installations while reducing the tooling required to terminate fiber optic cables!
Features and Benefits
• Integral proprietary & patented coating provides incredible glass protection
• Very small diameter distribution fiber for maximum fiber counts in conduit
limited installations
• Simplified termination process designed for ease of use & installation efficiency gains
• Bend longevity for 10,000x’s longer life time than normal fibers
• Increased safety factor due to the incredible bend insensitivity
• Glass fiber remains protected at all times from the elements
• High mechanical strength & superior fatigue values
• Ultra low attenuation loss on tight bend radius
• Exclusive 250um Soft Peel® jacket identifier in standard fiber color codes
Products
• OM3 50 micron Laser Optimized fiber cables. OM4, OM2 and singlemode available
• Two (2), four (4), & six (6) fiber Micro-Distribution format cables with a maximum
diameter of 3.2mm in both plenum and riser formats
• One (1) & two (2) fiber assembly style format for simplex & duplex patch cords or
one (1 ) & two (2) fiber installations
• Two (2) and Four (4) fiber Breakout format cables with 2mm sub units in plenum indoor
& indoor/outdoor formats
• Easy apply LC & SC connectors for quick & reliable field termination in convenient
10-packs
• SC-SC, LC-LC & SC-LC duplex fiber jumpers in one (1), two (2), three (3), five (5) & 10m lengths
Micro-Distribution Style
FIBER OPTIC CABLE 1 FIBER OM3 50/125 MULTIMODE
S50125MOM3P
Assembly Style
INDOOR/OUTDOOR FIBER OPTIC CABLE OM3 50/125 MULTIMODE
D50125MOM3R
Micro-Distribution Style
FIBER OPTIC CABLE 1 FIBER OM3 50/125 MULTIMODE
S50125MOM3R
Micro-Distribution Style
INDOOR FIBER OPTIC CABLE 1 FIBER OM3 50/125 MULTIMODE
6D50125MOM3P
Breakout Style
2B50125OM3P
INDOOR/OUTDOOR FIBER OPTIC CABLE 2 FIBER OM3 50/125 MULTIMODE
Micro-Distribution Style
INDOOR FIBER OPTIC CABLE 6 FIBER OM3 50/125 MULTIMODE
6D50125MOM3R
Micro-Distribution Style
2D50125MOM3P
INDOOR/OUTDOOR FIBER OPTIC CABLE 2 FIBER OM3 50/125 MULTIMODE
Breakout Style
INDOOR FIBER OPTIC CABLE OM3 50/125
4B50125OM3P
Assembly Style
INDOOR/OUTDOOR FIBER OPTIC CABLE OM3 50/125 MULTIMODE
D50125MOM3P
Micro-Distribution Style
INDOOR FIBER OPTIC CABLE 1 FIBER OM3 50/125 MULTIMODE
4D50125MOM3P
Breakout Style
INDOOR FIBER OPTIC CABLE 2 FIBER OM3 50/125 MULTIMODE
2B50125OM3R
Breakout Style
INDOOR FIBER OPTIC CABLE 2 FIBER OM3 50/125 MULTIMODE
4B50125OM3R
Micro-Distribution Style
INDOOR FIBER OPTIC CABLE 2 FIBER OM3 50/125 MULTIMODE
2D50125MOM3R
Micro-Distribution Style
INDOOR FIBER OPTIC CABLE 1 FIBER OM3 50/125 MULTIMODE
SPECIFICATIONS & IMAGES SUBJECT TO CHANGE
SPECIFICATIONS SUBJECT TO CHANGE
|
|
IMAGES NOT TO SCALE
IMAGES NOT TO SCALE
|
|
L0140
|
800.530.8998
800.530.8998
|
|
4D50125MOM3R
www.LibAV.com
www.LibAV.com
49
FIBER OPTIC CABLE SOLUTIONS
SSF FIBER SOLUTIONS
®
No stripping required | Incredible bend longevity assured for 10,000 x’s longer lifetime than normal glass fibers
Liberty’s SSF® fiber by Cleerline Technology redefines how optical cables can
be installed and terminated. SSF® fiber optics incorporate a patented polymeric
coating that surrounds the glass fiber. SSF® fibers are stronger, safer and allow
for faster terminations compared to all other glass fibers.
SSF® fiber is compatible with all common connector systems for standard 50/125 multimode and 9/125 single
mode fibers and are available in today’s most common cabling configurations for optical cables.
SSF® fiber optic cabling eliminates many of the processes involved in the termination of fiber optic cable
while adding strength and safety that is unmatched by any other optical fiber. SSF’s coated fiber provides
protection for bend longevity assured for 10,000 x’s longer lift times and superior mechanical strength
compared to all other commercially available glass fibers. This allows the installer to quickly terminate
mechanical splice style connections and eliminates the imperfections or scarring of
SSF Fiber
the glass caused by stripping when terminating either mechanical or epoxy style
connectors. SSF® supports all broadband applications.
Liberty’s SSF® fiber is compatible with all common connector systems on the market for
50/125um multimode and 9/125um single mode fiber optic cables. Get your connectors
and the complete termination kit at Liberty!
STRONGER
SAFER
FASTER!
Normal Fiber
125um
Hybrid Cladding
125um
Glass Cladding
STRONGER, SAFER, FASTER (SSF®): TERMINATIONS
Terminate SSF Fiber in 30 Seconds or Less!
SSF-LC-MMFPC-10
SSF-SC-MMFPC-10
SSF-FKIT03P
LC PLUG FIELD ASSY OM3 10PK
FIELD ASSEMBLY SC FIBER
OPTIC CONNECTOR FOR OM3/4
MULTIMODE
FIELD ASSEMBLY FIBER OPTIC
TERMINATION KIT
• LC Plug Format
• 50/125 Multimode Fiber OM2/3/4
• Sold in multiples of 10 only
• Fits Breakout and Distribution style cable
• Ideal for Stronger, Safer, Faster (SSF) fiber
• SC Plug Format
• 50/125 Multimode Fiber OM2/3/4
• Sold in multiples of 10 only
• Fits Breakout and Distribution style
terminations
• Termination Tooling Kit for SC, LC, and
ST Connectors
• Includes VFL, cleaver, scissors, stripper
• Ideally set up for SSF fiber termination
cable
• Ideal for Stronger, Safer, Faster (SSF) fiber
terminations
TECH SPECS
Liberty SSF 50/125μm Specialty OM3 Multimode Optical Fiber Characteristics Conditions Specified Values Unit SSF conforms to the requirement of IEC 60793 A1a,
ISO/IEC 11801 & ITU-T G.651.1. 850 nm Laser-Optomized 50 μm-core multimode fiber for 10 Gb/s & above applications
PHYSICAL CHARACTERISTICS
OVERFILLED MODAL BANDWIDTH
ENVIRONMENTAL CHARACTERISTICS
Core Diameter 50.0 ± 2.5 (μm)
850 nm ≤ 1500 (MHzØkm)
Temperature Dependence at 850 nm and 1300 nm ≤ 0.1 (dB/km)
Core Non- circularity ≤ 5 (%)
1300 nm ≤ 500 (MHzØkm)
Induced Attenuation – 40oC to +85oC
Core / Hybrid Cladding Concentricity Error ≤ 3.0 (μm)
Differential Mode Delay 850nm ≤ 2000 (MHz•km)
Water Soak Dependence at 850 nm and 1300 nm ≤ 0.2 (dB/km)
Hybrid Cladding Diameter 125 ± 1 (μm)
BACKSCATTER CHARACTERISTICS
Induced Attenuation at 23oC for 30 days
Hybrid Cladding Non-Circularity ≤ 3.0 (%)
Damp Heat Dependence at 850 nm and 1300 nm ≤ 0.2 (dB/km)
Attenuation Directional Uniformity ≤ 0.05 (dB/km)
Induced Attenuation at 85oC, 85%R.H., 30 days
Protective Coating Concentricity Error≤ 3.0 (μm)
Attenuation Uniformity ≤ 0.05 (dB)
Soft-Peel Jacket Identifier 245 ± 5
Group Index of Refraction
Coating Strip Force (typical) ≤ 100 (g)
850 nm 1.481
Color Coating Diameter 250 ± 10 (μm)
1300 nm 1.476
Fiber Curl ≤ 2 (m)
OPTICAL CHARACTERISTICS*
Attenuation Directional Uniformity ≤ 0.05 (dB/km)
Attenuation Coefficient
Proof Test 100 (Kps)
Attenuation Uniformity ≤ 0.05 (dB)
850 nm ≤ 3.0 (dB/km)
Bend Induced Attenuation at 1300 nm ≤ 1.0 (dB)
Group Index of Refraction
1300 nm ≤ 1.0 (dB/km)
(100 turns around a mandrel of 75 mm diameter)
850 nm 1.481
Dynamic fatigue 23oC, 41%RH (nd) >30
1300 nm 1.476
Dry Heat Dependence at 850 nm and 1300 nm ≤ 0.2 (dB/km)
Induced Attenuation at 85oC, 85%R.H., 30 days
Numerical Aperture 0.200 ± 0.015
*Ensured via minEMBC.per TIA/EIA 455-220A and IEC 60793-1-49, for high
performance laser based systems.
Length (Typical) 1.0 – 8.8 (Km)
SPECIFICATIONS & IMAGES SUBJECT TO CHANGE
50
|
IMAGES NOT TO SCALE
800.530.8998
|
L0140
|
|
800.530.8998
|
www.LibAV.com
www.LibAV.com
|
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
FIBER OPTIC CABLE SOLUTIONS
SSF JUMPER SOLUTIONS
®
Stronger, Safer, Faster (SSF®) Lifetime Fiber Optic Patch Cables
DOM3NLCLC
Stronger, Safer, Faster (SSF®) Lifetime Fiber Optic Patch Cable OM3 Laser Optimized Multimode LC-LC
Features and Benefits
• Duplex LC to Duplex LC FPC/SPC format connectors
• Stronger, Safer, Faster (SSF) fiber bulk cable
• 10,000 times the flex life of standard fiber cables
• Two (2) fiber 50/125 laser optimized multimode OM3 fiber
• Standard lengths 1, 2, 3, 5 & 10m
• NEC OFNR, CEC FT4 & RoHS compliant
Applications
• Super strong long life duplex fiber patch cables
• LAN 10/100/1000/10G ethernet
• Digital multimedia patching & interconnection
• Crestron, AMX & Savant standard fiber specification
DOM3NLCSC
MODEL
Description
DOM3LCLC01M
3.3’ Teal
DOM3LCLC02M
6.6’ Teal
DOM3LCLC03M
10’ Teal
Stronger, Safer, Faster (SSF®) Lifetime Fiber Optic Patch Cable OM3 Laser Optimized Multimode LC-SC
Features and Benefits
• Duplex LC to Duplex SC format connectors
• Stronger, Safer, Faster (SSF) fiber bulk cable
• 10,000 times the flex life of standard fiber cables
• Two (2) fiber 50/125 laser optimized multimode OM3 fiber
• Standard lengths 1, 2, 3, 5 & 10m
• NEC OFNR, CEC FT4 & RoHS compliant
Applications
• Super strong long life duplex fiber patch cables
• LAN 10/100/1000/10G ethernet
• Digital multimedia patching & interconnection
• Crestron, AMX & Savant standard fiber specification
DOM3NSCSC
TECH SPECS
TECH SPECS
MODEL
Description
DOM3LCSC01M
3.3’ Teal
DOM3LCSC02M
6.6’ Teal
DOM3LCSC03M
10’ Teal
Stronger, Safer, Faster (SSF®) Lifetime Fiber Optic Patch Cable OM3 Laser Optimized Multimode SC-SC
Features and Benefits
• Duplex SC to SC format connectors
• Stronger, Safer, Faster (SSF) fiber bulk cable
• 10,000 times the flex life of standard fiber cables
• Two (2) fiber 50/125 laser optimized multimode OM3 fiber
• Standard lengths 1, 2, 3, 5 & 10m
• NEC OFNR, CEC FT4 & RoHS compliant
Applications
• Super strong long life duplex fiber patch cables
• LAN 10/100/1000/10G ethernet
• Digital multimedia patching & interconnection
• Crestron, AMX & Savant standard fiber specification
SPECIFICATIONS & IMAGES SUBJECT TO CHANGE
SPECIFICATIONS SUBJECT TO CHANGE
|
|
IMAGES NOT TO SCALE
IMAGES NOT TO SCALE
|
|
L0140
|
800.530.8998
800.530.8998
|
|
TECH SPECS
MODEL
Description
DOM3SCSC01M
3.3’ Teal
DOM3SCSC02M
6.6’ Teal
DOM3SCSC03M
10’ Teal
www.LibAV.com
www.LibAV.com
51
FIBER
OPTICCABLE:
CABLE SOLUTIONS
BULK FIBER
STANDARD TIGHT BUFFERED
MULTIMODE OM1: PLENUM AND NON-PLENUM
BX004KWLS9OP ORANGE BREAKOUT STYLE INDOOR/OUTDOOR PLENUM FIBER OPTIC CABLE 4 FIBER OM1 62.5/125 MULTIMODE REEL
• 4 fiber OM1 62.5/125 multimode
• Dual layer tight buffer 900 micron
• Central strength member
• Breakout construction
• UV stabilized PVC jacket
• NEC OFNP, CEC FT6, Sunlight resistant,
RoHS compliant
• Fiber is cut to order
DX002KWLS9KR BLACK DISTRIBUTION STYLE INDOOR/OUTDOOR FIBER OPTIC CABLE 2 FIBER OM1 62.5/125 MULTIMODE REEL
• Sunlight resistant, suitable for wet locations
• NEC OFNR, CEC FT4, RoHS compliant
• Fiber is cut to order
• 2 fiber OM1 62.5/125 multimode
• Dual layer tight buffer 900 micron
• Central strength member and kevlar yarn
• Distribution construction
• UV stabilized PVC jacket
BX004DWLS9KR BLACK BREAKOUT STYLE INDOOR/OUTDOOR FIBER OPTIC CABLE 4 FIBER OM1 62.5/125 MULTIMODE REEL
• 4 Fiber 62.5 micron 62.5/125 Multimode OM1 Fiber • UV Stabilized Polyvinyl Chloride jacket
• Dual Layer 900 micron tight buffer
• NEC OFNR, CEC FT4, Sunlight Resistant, RoHS Compliant
• Breakout Construction inner jackets
• Fiber is cut to order
with kevlar yarn
• 4 jacketed fibers around a central member
DX006KWLS9KR BLACK DISTRIBUTION STYLE INDOOR/OUTDOOR FIBER OPTIC CABLE 6 FIBER OM1 62.5/125 MULTIMODE REEL
• 6 fiber OM1 62.5/125 multimode
• Dual layer tight buffer 900 micron
• Central strength member and kevlar yarn
• Distribution construction
• UV stabilized PVC jacket
• Sunlight resistant, suitable for wet locations
• NEC OFNR, CEC FT4, RoHS compliant
• Fiber is cut to order
MULTIMODE OM2: PLENUM AND NON-PLENUM
DX002SALS9OP ORANGE FIBER 2F 50 OM2 OFNP DIST REEL
•
• 2 Fiber 50/125 micron OM2 Multimode Fiber
• 900 Micron Dual Layer Tight Buffer
•
• Aramid Yarn Strength Members (Kevlar)
• Distribution Format
• Indoor Only Plenum rated PVC Alloy Orange Jacket
800m, 1600m Standard Spool Lengths,
Fiber is cut to order
NEC OFNP, CEC FT6, RoHS Compliant
BX004DALS9KR BLACK BREAKOUT STYLE INDOOR/OUTDOOR FIBER OPTIC CABLE 4 FIBER OM2 50/125 MULTIMODE REEL
• Orange colored jacket indicates OM2
• NEC OFNR, CEC FT4, ,Sunlight Resistant, RoHS
• 4 Fiber 50/125 Multimode OM2 Fibers
• Dual Layer 900 micron tight buffer
• Breakout Construction inner jackets with
kevlar yarn
• 4 jacketed fibers around a central member
• UV Stabilized Polyvinyl Chloride jacket
Compliant
• Fiber is cut to order
MULTIMODE OM3: PLENUM AND NON-PLENUM
BX004DWLT9QR TEAL BREAKOUT STYLE INDOOR/OUTDOOR PLENUM FIBER OPTIC CABLE 4 FIBER OM3 50/125 MULTIMODE REEL
• 4 fiber OM3 50/125 laser optimized multimode
• Dual layer tight buffer 900 micron
• Central strength member
• Breakout construction
• UV stabilized PVC jacket
2
52
| www.LibAV.com |
800.530.8998 | www.LibAV.com |
800.530.8998
• NEC OFNP, CEC FT6, Sunlight resistant, RoHS compliant
• Fiber is cut to order
SPECIFICATIONS SUBJECT TO CHANGE
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
|
IMAGES NOT TO SCALE
MULTIMODE OM3: PLENUM AND NON-PLENUM
FIBERFIBER
OPTICCABLE:
CABLE STANDARD
SOLUTIONS
•
BULK
TIGHT BUFFERED ••
•
BX002DALT9QR TEAL BREAKOUT STYLE INDOOR/OUTDOOR FIBER OPTIC CABLE 2 FIBER OM3 50/125 MULTIMODE REEL
2 fiber OM3 50/125 laser optimized multimode
Dual layer tight buffer 900 micron
Central strength member
Breakout construction
UV stabilized PVC jacket
•
•
MULTIMODE OM3: PLENUM AND
NON-PLENUM
•
NEC OFNR, CEC FT4, Sunlight resistant, RoHS compliant
Fiber is cut to order
BX002DALT9QR TEAL BREAKOUT STYLE INDOOR/OUTDOOR FIBER OPTIC CABLE 2 FIBER OM3 50/125 MULTIMODE REEL
• 2 fiber OM3 50/125 laser optimized multimode
• Dual layer tight buffer 900 micron
• Central strength member
• Breakout construction
• UV stabilized PVC jacket
• NEC OFNR, CEC FT4, Sunlight resistant, RoHS compliant
• Fiber is cut to order
BX002DALT9QR
BX004DALT9QR TEAL
TEAL BREAKOUT
BREAKOUT STYLE
STYLE INDOOR/OUTDOOR
INDOOR/OUTDOOR FIBER
FIBER OPTIC
OPTIC CABLE
CABLE 24FIBER
FIBEROM3
OM350/125
50/125MULTIMODE
MULTIMODEREEL
REEL
fiber OM3
OM3 50/125
50/125 laser
laser optimized
optimized multimode
multimode
• 24fiber
Dual layer
layer tight
tight buffer
buffer 900
900 micron
micron
• Dual
Central strength
strength member
member
• Central
Breakout construction
construction
• Breakout
UV stabilized
stabilized PVC
PVC jacket
jacket
• UV
CEC FT4,
FT4,Sunlight
Sunlightresistant,
resistant,RoHS
RoHS
• NEC OFNR, CEC
compliant
compliant
Fiber is cut
cut to
to order
order
• Fiber
BX004DALT9QR
STYLE
INDOOR/OUTDOOR
FIBER
OPTIC
CABLE
4 FIBER
OM3OM3
50/125
MULTIMODE
REELREEL
DX004DALT9QR TEAL
TEAL BREAKOUT
DISTRIBUTION
STYLE
INDOOR/OUTDOOR
FIBER
OPTIC
CABLE
4 FIBER
50/125
MULTIMODE
• 44 fiber
fiber OM3
OM3 50/125
50/125 laser
laser optimized
optimized multimode
multimode
• Dual
Dual layer
layer tight
tight buffer
buffer 900
900 micron
micron
• Central
Central strength
strength member
member
• Breakout
Breakout construction
construction
• UV
UV stabilized
stabilized PVC
PVC jacket
jacket
• NEC
NEC OFNR,
OFNR, CEC
CEC FT4,
FT4, Sunlight
Sunlight resistant,
resistant, RoHS
RoHS compliant
compliant
• FFiber
iber is
is cut
cut to
to order
order
DX004DALT9QR TEAL
TEAL BREAKOUT
DISTRIBUTION
STYLE
INDOOR/OUTDOOR
FIBER
OPTIC
CABLE
4 FIBER
50/125
MULTIMODE
BX004DALT9QR
STYLE
INDOOR/OUTDOOR
FIBER
OPTIC
CABLE
4 FIBER
OM3OM3
50/125
MULTIMODE
REELREEL
fiber OM3
OM3 50/125
50/125 laser
laser optimized
optimized multimode
multimode
• 44 fiber
Dual layer
layer tight
tight buffer
buffer 900
900 micron
micron
• Dual
Central strength
strength member
member
• Central
Breakout construction
construction
• Breakout
UV stabilized
stabilized PVC
PVC jacket
jacket
• UV
NEC OFNR,
OFNR, CEC
CEC FT4,
FT4, Sunlight
Sunlight resistant,
resistant, RoHS
RoHS compliant
compliant
• NEC
• FFiber
iber is
is cut
cut to
to order
order
CUSTOM & PREMADE FIBER OPTICS SOLUTIONS
CUSTOM FIBER INSTALL CABLES | CUSTOM FIBER PATCH CORDS
DX004DALT9QR
TEAL DISTRIBUTION
STYLE INDOOR/OUTDOOR
OPTIC CABLE 4 CABLES
FIBER OM3 50/125
MULTIMODEFIBER
REEL PATCH CORDS
DATA CENTER
CONFIGURATIONS
| LEMO®FIBER
BROADCAST
| STANDARD
• 4 fiber OM3 50/125 laser optimized multimode
• NEC OFNR, CEC FT4, Sunlight resistant, RoHS compliant
• Fiber is cut to order
• Dual layer tight buffer 900 micron Liberty’s team
of experienced sales
• Central strength member
Breakout
construction
•
professionals and highly trained fiber
PVC jacket
• UV stabilized
CUSTOM FIBER
INSTALL
CABLES | CUSTOM
FIBER PATCH
CORDS
technicians
can design
solutions that will
CUSTOM & PREMADE FIBER OPTICS SOLUTIONS
DATA CENTER CONFIGURATIONS | LEMO® BROADCAST CABLES
PATCH
work for| STANDARD
every type FIBER
of fiber
optic CORDS
installation.
As a certified FibertronTM and Corning GoldTM
Liberty’s
team our
of experienced
manufacturer,
custom fibersales
assemblies
professionals
and
highly
trained
are unmatched in the AV industryfiber
for
technicians
can
design
solutions
that
CUSTOM FIBER INSTALL CABLES | CUSTOM
FIBER
PATCH
CORDS
performance, reliability and value. will
work for| STANDARD
every type FIBER
of fiber
opticCORDS
installation.
DATA CENTER CONFIGURATIONS | LEMO® BROADCAST CABLES
PATCH
TM
As a certified Fibertron and Corning GoldTM
Liberty’s
team our
of experienced
manufacturer,
custom fibersales
assemblies
professionals
and
fiber
are unmatched
in highly
the AVtrained
industry
for
technicians
can
design solutions
that will
performance,
reliability
and value.
work for every type of fiber optic installation. 3
SPECIFICATIONS SUBJECT TO CHANGE | IMAGES NOT TO SCALE | 800.530.8998 | www.LibAV.com
Liberty distributes Optical Cable Corporation fiber, check
our website
for TM
many
more choices!
and Corning
GoldTM
As a certified
Fibertron
manufacturer, our custom fiber assemblies
are unmatched in the AV industry for
performance, reliability and value.
SPECIFICATIONS SUBJECT TO CHANGE | IMAGES NOT TO SCALE | 800.530.8998 | www.LibAV.com
3
CUSTOM & PREMADE FIBER OPTICS SOLUTIONS
SPECIFICATIONS SUBJECT TO CHANGE
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
|
IMAGES NOT TO SCALE
|
800.530.8998
|
800.530.8998
|
www.LibAV.com
|
www.LibAV.com
3
53
FIBER
OPTIC CABLE
SOLUTIONS
CONNECTORS:
CORNING
CONNECTORS: CORNING
CORNING: OM1
95-000-41
95-000-51
95-000-99
CORNING: OM1
95-000-41
95-000-51
CORNING UNICAM SC FIBER OPTIC
CONNECTOR FOR OM1 62.5/125
95-000-99
CORNING UNICAM ST® COMPATIBLE
FIBER OPTIC CONNECTOR FOR OM1
62.5/125
CORNING UNICAM LC FIBER OPTIC
CONNECTOR FOR OM1 62.5/125
CORNING UNICAM ST® COMPATIBLE
CORNING
Format UNICAM LC FIBER OPTIC
• SC Plug FormatCORNING UNICAM SC FIBER OPTIC
• LC Plug
CONNECTOR
FIBER OPTIC CONNECTOR FOR OM1 62.5/125
CONNECTOR
FOR OM1 62.5/125
Fiber OM1 FOR OM1 62.5/125• ST Plug Format
Multimode Fiber
• 62.5/125 Multimode
•
62.5/125Fiber
62.5/125
Multimode
•
Multiple
strain
relief
boots
Individual
Bag
with
Multiple
strain relief boots
• Individual Bag• with
SC Plug Format
•
• LC Plug Format
withFormat
Multiple strain relief boots
ST Plug
• Individual• Bag
and Multimode
Distribution
style
cable
Fiber
OM1
Breakout
and Distribution
style cable
• Fits both Breakout
Multimode
Fiber
• 62.5/125
• Fits both
• 62.5/125
and Distribution
62.5/125 Multimode
Fiber style cable
• Fits both •Breakout
Unicam
System
BagPFC
with
Multiple strain relief boots
BagUnicam
with Multiple
strain relief boots
for Corning
PFC System
• Individual
• Specific for Corning
• Individual
• Specific
Bag with
Multiple
strain relief boots
Specific for
Corning Unicam
PFC
System
• Individual
Fits both Breakout and Distribution style cable
• Fits both Breakout and Distribution style •cable
SAFER,
FASTER
(SSF®):•• Specific
OM1for Corning Unicam PFC System
and Distribution
style cable
• Fits both Breakout
• Specific for Corning Unicam PFC System STRONGER,
CONNECTORS: STRONGER, SAFER, FASTER (SSF®) / KEYSTONE
• Specific for Corning Unicam PFC System
FALCM10
FASCM10
KEYSTON
ISK-LC-WH
CORNING: OM2/3/4
CORNING: OM2/3/4
95-050-41
95-050-41-X
95-050-41
95-050-51-X
95-050-41-X
95-050-51-X
LC PLUG FIELD ASSY OM3 10PK
FIELD ASSEMBLY SC FIBER
OPTIC CONNECTOR FOR OM3/4
MULTIMODE
• LC Plug Format
• 50/125 Multimode Fiber OM2/3/4
• SC Plug Format
• Sold in multiples of 10 only
FiberST®
OM3 COMPATIBLE
or OM4
• 50/125 Multimode
CORNING UNICAM SC FIBER OPTIC
CORNING
UNICAM
SC
FIBER
OPTIC
CORNING
UNICAM
Fits
Breakout
and
Distribution
style
cable
•
CORNING
UNICAM
SC FIBER OPTIC
CORNING
UNICAM
SC
FIBER OPTICFIBER
UNICAM
COMPATIBLE
in multiples
of 10 only ST®FOR
• SoldCORNING
CONNECTOR
FOR OM2
50/125
CONNECTOR
FORSafer,
OM3/4
OPTIC
CONNECTOR
Ideal for Stronger,
Faster50/125
(SSF) Fiber
•
CONNECTOR FOR OM2 50/125
CONNECTOR FOR OM3/4 50/125 OM3/4
OPTIC
CONNECTOR
FOR
terminations
Breakout
and Distribution
style cable
50/125
• FitsFIBER
OM3/4 50/125
• SC Plug Format• SC Plug Format
• SC Plug Format
Ideal
for
Stronger,
Safer,
Faster
(SSF)
•
Plug Format
• SCOptimized
Fiber OM2
• 50/125 Multimode
Multimode OM3 / OM4
STFiber
Plug terminations
• 50/125 Laser
50/125 Multimode Fiber OM2
• with
50/125 Laser Optimized Multimode OM3 / OM4 •
Plug Format
•
• STFormat
Individual
Bag
Multiple
strain
relief
boots
•
with Multiple
relief
boots
Laser
Multimode
OM3OM3
/ OM4
• Individual• Bag
• Individual Bag with Multiple strain relief boots
Individual
Bag withstrain
Multiple
strain
relief boots• 50/125
50/125Optimized
Laser Optimized
Multimode
/ OM4
•
cable style •cable
• Fits both Breakout
Fits both •Breakout
Distribution
style cable
Bag with
strainstrain
reliefrelief
boots
bothDistribution
Breakout andstyle
Distribution
• Fits and
Fits bothand
Breakout
and Distribution
style cable• Individual
BagMultiple
with Multiple
boots
• Individual
Unicam
PFC System
• Specific for Corning
Corningfor
Unicam
PFC
System
and Distribution
stylestyle
cable
for Corning
Unicam PFC System • Specific for
• Fits both
• Specific
Corning
Unicam
PFC System
both Breakout
and Distribution
cable
• Specific
• FitsBreakout
for Corning
Unicam
PFC System
for Corning
Unicam
PFC System
• Specific
• Specific
KEYSTONE
MULTIMOD
INSERTS
• LC Multimode
through forma
• Duplex format
• Multimode OM
• Keystone snap
• Non-recessed
• Compatible w
TOOLING: CORNING / STRONGER, SAFER, FASTER (SSF®) / PU
CORNING
95-050-99-X 95-050-99-X
TKT-UNICAM-PFC
FCC-CLEANER-FIBER
CORNING UNICAM LC FIBER OPTIC
CORNING UNICAM
LC FIBER
OPTIC50/125
CONNECTOR
FOR OM3/4
CONNECTOR FOR OM3/4 50/125
FCC-WIPES
NEED HELP?
NEED
HELP?
CORNING
FIBER
OPTIC UNICAM
• LC Plug Format
We offer technical
assistance
TERMINATION
SYSTEM
FIBER
• LC Plug Format• 50/125 Laser Optimized Multimode OM3 / OM4
We
offer
technical
FLUIDassistance
onCLEANING
all of our
products
or applications!
Bag with Multiple
strain relief boots
• IndividualMultimode
OM3 / OM4
• 50/125 Laser Optimized
CORNING UNICAM FIBER
Fits both
Breakout
and
Distribution
on all of• our
products
or applications!
Multiple
strain
relief
boots style cable
• Individual Bag• with
Dispensing
bottle
of Fiber Cleaning
Fluid
Call Single
us at
800-530-8998
or email
OPTIC TERMINATION SYSTEM
Corning Unicam
System
• Specific
and for
Distribution
style PFC
cable
• Fits both Breakout
Replenishment
for
the
TKT-UNICAM-PFC tool kit
•
• Specific for Corning Unicam PFC System
6
6
54
Call us at 800-530-8998 or email
Tooling Kit for SC, LC,
be used with any fiber or fiber tool kit
• Termination
• Can
[email protected]
and ST Connectors
[email protected]
Suitcase design can go
• Ergonomic
anywhere
Supplies included, DVD and
• All
STRONGER, SAFER,
printed instructions
FASTER (SSF®)
Visual Fault Locator built into
•
800.530.8998
| www.LibAV.com | SPECIFICATIONS SUBJECT TO CHANGE | IMAGES NOT TO SCALE
the termination tool
LWFOTKT
• Precision Cleaver
800.530.8998 | www.LibAV.com | SPECIFICATIONS SUBJECT TO CHANGE | IMAGES NOT TO SCALE
800.530.8998
|
www.LibAV.com
|
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
CORNING FI
TERMINATIO
CLEANING C
• Single Dispens
• Replenishment
• Can be used w
PULL SOC
PS2-6
CABLES: CATEGORY CABLE SOLUTIONS CABLES
• COOL SPOOL® REELS & PAYOUT BOXES
• CATEGORY 5E, 6, 6A & CATEGORY 7
• SHIELDED AND UNSHIELDED
• PLENUM AND RISER RATED
• TRULY 3RD PARTY CERTIFIED BY UL OR ETL
• ABSOLUTELY COMPLIANT!
• HIGH QUALITY PRODUCT
• COMPETITIVE PRICING
24-4P-L7SH SHIELDED S/FTP ISO 11801 CLASS F CATEGORY 7
• S olid annealed
•
•
•
bare copper conductors
H
DPE or FEP insulation
I ndividually shielded pairs
w/overall braid
C
M rated, RoHS compliant
24-4P-P-L7SH SHIELDED S/FTP ISO 11801 CLASS F CATEGORY 7 - PLENUM
FEATURES
• S olid annealed
•
•
•
bare copper conductors
H
DPE or FEP insulation
I ndividually shielded pairs
w/overall braid
C
MP rated, RoHS compliant
24-4P-L6ASH SHIELDED F/UTP CATEGORY 6A
• S olid annealed
•
bare copper conductors
H
DPE or FEP insulation
T
ightly twisted
& overall foil shielded
C
MR rated, RoHS compliant
24-4P-P-L6ASH SHIELDED F/UTP CATEGORY 6A - PLENUM
• S olid annealed
•
bare copper conductors
H
DPE or FEP insulation
T
ightly twisted
& overall foil shielded
C
MP rated, RoHS compliant
24-4P-L6-EN EN SERIES CATEGORY 6
• S olid annealed
•
•
•
bare copper conductors
H
DPE or FEP insulation
T
ightly twisted & unshielded
C
MR rated, RoHS compliant
24-4P-P-L6-EN EN SERIES CATEGORY 6 - PLENUM
• C ool Spool Reels
• ISO 11801 Class F, AKA Cat 7
• 1 0GB Ethernet/4K HDBaseT
• B lue jacket only
CONNECTOR(S)
Tele-TitanXg®:
106190 / 106192
Field Terminable:
OCCSFP6A
Field Terminable:
1401405012-I
• C ool Spool Reels
• A NSI/TIA-568C Verified Cat 6a
• 1 0GB Ethernet/HDBaseT
hite jacket only
•W
CONNECTOR(S)
Standard:
111S08080016C34
Kitted:
RJ45-STP-L6
Tele-TitanXg®:
106190 / 106192
Field Terminable:
OCCSFP6A
• C ool Spool Reels
• A NSI/TIA-568C Verified Cat 6a
• 1 0GB Ethernet/HDBaseT
hite jacket only
•W
CONNECTOR(S)
Standard:
111S08080016C34
Kitted:
RJ45-STP-L6
Tele-TitanXg®:
106190 / 106192
Field Terminable:
OCCSFP6A
• S olid annealed
•
•
•
bare copper conductors
H
DPE or FEP insulation
T
ightly twisted & unshielded
C
MP rated, RoHS compliant
IMAGES NOT TO SCALE
• C ool Spool Reels
• A NSI/TIA-568C Verified Cat 6
• P ositive ACR to 550 MHz
• 1 0 colors
CONNECTOR(S)
EZ-RJ45®:
100 011LW
Standard:
11108080034
|
• C ool Spool Reels
• A NSI/TIA-568C Verified Cat 6
• P ositive ACR to 550 MHz
• 10 colors
800.530.8998
|
CONNECTOR(S)
EZ-RJ45®:
100 011LW
Standard:
11108080034
www.LibAV.com
TOOL KIT
90170
-N/A-N/A-
BEST
HIGH QUALITY FOR SUPERIOR PERFORMANCE
CRIMP TOOLING
12516
-N/A-N/A-
TOOL KIT
90170
-N/A-N/A-
BETTER
CRIMP TOOLING
100054LW
100054LW
12516
-N/A-
TOOL KIT
90131LW
90131LW
90170
-N/A-
BETTER
CRIMP TOOLING
100054LW
100054LW
12516
-N/A-
TOOL KIT
90131LW
90131LW
90170
-N/A-
BEST
CRIMP TOOLING
100054LW
100054LW
TOOL KIT
90131LW
90131LW
BEST
HIGH QUALITY FOR SUPERIOR PERFORMANCE
FEATURES
|
12516
-N/A-N/A-
HIGH QUALITY FOR SUPERIOR PERFORMANCE
FEATURES
SPECIFICATIONS SUBJECT TO CHANGE
Tele-TitanXg®:
106190 / 106192
Field Terminable:
OCCSFP6A
Field Terminable:
1401405012-I
CRIMP TOOLING
HIGH QUALITY FOR SUPERIOR PERFORMANCE
FEATURES
•
•
• C ool Spool Reels
• ISO 11801 Class F, AKA Cat 7
• 1 0GB Ethernet/4K HDBaseT
• B lue jacket only
CONNECTOR(S)
HIGH QUALITY FOR SUPERIOR PERFORMANCE
FEATURES
•
•
BEST
HIGH QUALITY FOR SUPERIOR PERFORMANCE
FEATURES
CRIMP TOOLING
100054LW
100054LW
TOOL KIT
90131LW
90131LW
55
CABLES: CATEGORY CABLE SOLUTIONS CABLES
24-4P-L6SH SHIELDED F/UTP CATEGORY 6
• S olid annealed
•
•
•
bare copper conductors
H
DPE or FEP insulation
T
ightly twisted & unshielded
C
MR rated, RoHS compliant
24-4P-P-L6SH SHIELDED F/UTP CATEGORY 6 - PLENUM
• S olid annealed
bare copper conductors
H
DPE or FEP insulation
T
ightly twisted & unshielded
C
MP rated, RoHS compliant
24-4P-L6-HT HOMETRAX™ CATEGORY 6 CABLES
• S olid annealed
•
•
bare copper conductors
H
igh Density Polyethylene
Insulation
T
ightly twisted & unshielded
N
EC CMR, CEC CMR FT4,
RoHS compliant
24-4P-L6SH-HT SHIELDED F/UTP CATEGORY 6
• S olid annealed
•
• C ool Spool Reels
• A NSI/TIA-568C Verified Cat 6
• P ositive ACR to 550 MHz
• 3 colors
• N ested box packaging only
• A NSI/TIA-568C Verified Cat 6
• P ositive ACR to 275 MHz
• 4 colors
• C ool Spool Reels
• A NSI/TIA-568C Verified Cat 6
• P ositive ACR past 300 MHz
• 3 colors
bare copper conductors
H
DPE or FEP insulation
T
ightly twisted
& overall foil shielded
C
M rated, RoHS compliant
24-4P-L5-EN EN SERIES CATEGORY 5E
CONNECTOR(S)
100054LW
100054LW
12516
-N/A-
Standard:
111S08080016C34
Kitted:
RJ45-STP-L6
Tele-TitanXg®:
106190 / 106192
Field Terminable:
OCCSFP6A
CONNECTOR(S)
100054LW
100054LW
• S olid annealed
• C ool Spool Reels
•
•
•
•
•
•
bare copper conductors
H
DPE or FEP insulation
T
ightly twisted
& overall foil shielded
C
MR rated, RoHS compliant
24-4P-P-L5-EN EN SERIES CATEGORY 5E - PLENUM
& Nested Boxes
A
NSI/TIA-568C Verified Cat 5e
P
ositive ACR to 350 MHz
10 colors
100054LW
100054LW
12516
-N/A-
• S olid annealed
• C ool Spool Reels
•
•
•
•
•
•
bare copper conductors
H
DPE or FEP insulation
T
ightly twisted
& overall foil shielded
C
MP rated, RoHS compliant
24-4P-L5SH-EN EN SERIES SHIELDED F/UTP CATEGORY 5E
• S olid annealed
•
bare copper conductors
H
DPE or FEP insulation
T
ightly twisted
& overall foil shielded
C
MR rated, RoHS compliant
800.530.8998
100054LW
100054LW
& Nested Boxes
A
NSI/TIA-568C Verified Cat 5e
P
ositive ACR to 350 MHz
10 colors
100054LW
100054LW
EZ-RJ45®:
100 003B
Standard:
10005USOP
|
• C ool Spool Reels
• A NSI/TIA-568C Verified Cat 5e
• P ositive ACR past 200 MHz
• 4 colors
www.LibAV.com
|
CONNECTOR(S)
TOOL KIT
90131LW
90131LW
TOOL KIT
90131LW
90131LW
90170
-N/A-
TOOL KIT
90131LW
90131LW
BETTER
CRIMP TOOLING
TOOL KIT
90131LW
90131LW
BETTER
IDEAL FOR BUDGET CONSCIOUS INSTALLATIONS
FEATURES
•
•
EZ-RJ45®:
100 003B
Standard:
10005USOP
CONNECTOR(S)
90131LW
90131LW
90170
-N/A-
BETTER
CRIMP TOOLING
HIGH QUALITY FOR SUPERIOR PERFORMANCE
FEATURES
TOOL KIT
BETTER
CRIMP TOOLING
Standard:
111S08080016C34
Kitted:
RJ45-STP-L6
Tele-TitanXg®:
106190 / 106192
Field Terminable:
OCCSFP6A
CONNECTOR(S)
90131LW
90131LW
90170
-N/A-
BETTER
CRIMP TOOLING
EZ-RJ45®:
100 011LW
Standard:
11108080034
CONNECTOR(S)
TOOL KIT
BETTER
CRIMP TOOLING
HIGH QUALITY FOR SUPERIOR PERFORMANCE
FEATURES
56
100054LW
100054LW
12516
-N/A-
Standard:
111S08080016C34
Kitted:
RJ45-STP-L6
Tele-TitanXg®:
106190 / 106192
Field Terminable:
OCCSFP6A
HIGH QUALITY FOR SUPERIOR PERFORMANCE
FEATURES
•
•
CRIMP TOOLING
IDEAL FOR BUDGET CONSCIOUS INSTALLATIONS
FEATURES
•
• C ool Spool Reels
• A NSI/TIA-568C Verified Cat 6
• P ositive ACR to 550 MHz
• 3 colors
CONNECTOR(S)
HIGH QUALITY FOR SUPERIOR PERFORMANCE
FEATURES
•
•
•
BETTER
HIGH QUALITY FOR SUPERIOR PERFORMANCE
FEATURES
CRIMP TOOLING
EZ-RJ45®:
100 003B
Standard:
10005USOP
SPECIFICATIONS SUBJECT TO CHANGE
100054LW
100054LW
|
TOOL KIT
90131LW
90131LW
IMAGES NOT TO SCALE
CABLES: CATEGORY CABLE SOLUTIONS CABLES
24-4P-P-L5SH EN SERIES SHIELDED F/UTP CATEGORY 5E - PLENUM
FEATURES
• S olid annealed
•
•
•
bare copper conductors
H
DPE or FEP insulation
T
ightly twisted
& overall foil shielded
C
MP rated, RoHS compliant
24-4P-L5-HT HOMETRAX™ CATEGORY 5E CABLES
• S olid annealed
•
•
bare copper conductors
H
igh Density
Polyethylene Insulation
T
ightly twisted & unshielded
N
EC CMR, CEC CMR FT4,
RoHS compliant
24-4P-L5SH-HT HOMETRAX™ SHIELDED F/UTP CATEGORY 5E
• S olid annealed
•
EZ-RJ45®:
100 003B
Standard:
10005USOP
CRIMP TOOLING
TOOL KIT
100054LW
100054LW
90131LW
90131LW
BETTER
• N ested box packaging only
• A NSI/TIA-568C Verified Cat 5e
• P ositive ACR past 200 MHz
• 4 colors
CONNECTOR(S)
EZ-RJ45®:
100 003B
Standard:
10005USOP
CRIMP TOOLING
TOOL KIT
100054LW
100054LW
90131LW
90131LW
BETTER
IDEAL FOR BUDGET CONSCIOUS INSTALLATIONS
FEATURES
•
•
• C ool Spool Reels
• A NSI/TIA-568C Verified Cat 5e
• P ositive ACR past 200 MHz
• 4 colors
CONNECTOR(S)
IDEAL FOR BUDGET CONSCIOUS INSTALLATIONS
FEATURES
•
BETTER
IDEAL FOR BUDGET CONSCIOUS INSTALLATIONS
bare copper conductors
H
DPE or FEP insulation
T
ightly twisted &
overall foil shielded
C
MR rated, RoHS compliant
• P lain wooden spools
• A NSI/TIA-568C Verified Cat 5e
• 3 colors
CONNECTOR(S)
EZ-RJ45®:
100 003B
Standard:
10005USOP
CRIMP TOOLING
TOOL KIT
100054LW
100054LW
90131LW
90131LW
LAN TOOLS & TERMINATION KITS
90170
12516
• Large diameter Cat 6, 6A &
• Large diameter Cat 6, 6A &
• L AN up to 10G networking,
• L AN up to 10G networking,
100016
100054LW
• T ermination of RJ45 & RJ25
• Modular plug crimp & cut action
• T ermination of EZ-RJ45
• 4P4C through 8P8C formats
• L AN & Balun support
• 75% better connector support
TELE-TITANXG CAT6A/10GIG
STRAIN RELIEF CRIMP TOOL
NCS TELE-TITANXG CAT6A/10GIG
CRIMP TOOL KIT
7 terminations
7 terminations
HDBaseT cable terminations
HDBaseT cable terminations
WHITE CATMASTER
TOOL KIT
HEAVY DUTY EZ-RJ45
CRIMP TOOL
(RJ11, RJ12) plugs
for EZ-RJ45 connectors
feed through plugs
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
(RJ9/RJ11/RJ45)
to reduce issues
|
800.530.8998
|
www.LibAV.com
57
CABLES: RF COAXIAL SOLUTIONS
• COOL SPOOL® REELS AND PAYOUT BOXES
• SWEEP TESTED TO 3.0 GHZ
• DUAL AND QUAD SHIELDED
• UL OR ETL LISTED
• MANUFACTURED TO SCTE REQUIREMENTS
• MATCHING C-TEC2 COMPRESSION PLUGS
• NO MAGNESIUM BRAID SHIELDS HERE
• COMPETITIVE PRICING
RG6-CM
IDEAL FOR MOST RF VIDEO APPLICATIONS
WHERE DC POWER IS NOT NEEDED
DUAL SHIELD NON-PLENUM RG6 FOR CATV & DBS
• Solid copper-clad steel conductors
• Foamed Polyethylene Insulation
• B onded foil & 60% aluminum braid shields
• N EC CM, CEC CM RoHS compliant
RG6-P-CATV
• Solid copper-clad steel conductors
• Foamed Polyethylene Insulation
• B onded foil & 60% aluminum braid shields
• N EC CM, CEC CM RoHS compliant
IDEAL ALL AROUND RF VIDEO CABLE
BETTER
• Cool Spool Reels
• Sweep Test to 3.0 GHz
• Excellent SRL ration
• 2 colors
IDEAL FOR RF VIDEO DC REQUIRED APPLICATIONS
WHERE EXTERNAL INTERFERENCE RESISTANCE IS NEEDED
QUAD SHIELD NON-PLENUM RG6 FOR CATV & DBS
• Solid annealed bare copper conductors
• H DPE or FEP insulation
• Tightly twisted & overall foil shielded
• CM rated, RoHS compliant
BETTER
• Cool Spool Reels
• Sweep Test to 3.0 GHz
• Excellent SRL ration
• 2 colors
IDEAL FOR RF VIDEO NON-DC REQUIRED APPLICATIONS
WHERE EXTERNAL INTERFERENCE RESISTANCE IS NEEDED
RG6-QUAD-CMP QUAD SHIELD PLENUM RG6 FOR CATV & DBS
• Solid annealed bare copper conductors
• H DPE or FEP insulation
• Tightly twisted & overall foil shielded
• CMP rated, RoHS compliant
• Cool Spool Reels
• Sweep Test to 3.0 GHz
• Excellent SRL ration
• 2 colors
• Solid annealed bare copper conductors
• H igh Density Polyethylene Insulation
• Tightly twisted & overall foil shielded
• B raid shield flooded for water repellant gel
RG6Q-CM-SIAM QUAD SHIELD NON-PLENUM DUAL RG6 FOR CATV & DBS
BETTER
• Cool Spool Reels
• Sweep Test to 3.0 GHz
• Excellent SRL ration
• 2 colors
IDEAL FOR RF VIDEO NON-DC REQUIRED APPLICATIONS
WHERE EXTERNAL INTERFERENCE RESISTANCE IS NEEDED
• Solid copper-clad steel center conductor
• Foamed Polyethylene Insulation
• Two 100% foil & two braid shields 60/40%
• N EC CM, CEC CMG FT4, RoHS compliant
|
BETTER
IDEAL FOR RF VIDEO NON-DC REQUIRED APPLICATIONS
FOR OUTDOOR & DIRECT BURIAL
RG6-QUAD-DB QUAD SHIELD OUTSIDE PLANT RG6 FOR CATV & DBS
800.530.8998
• Cool Spool Reels
• Sweep Test to 3.0 GHz
• Excellent SRL ration
• 2 colors
IDEAL FOR RF VIDEO NON-DC REQUIRED APPLICATIONS
WHERE EXTERNAL INTERFERENCE RESISTANCE IS NEEDED
• Solid annealed bare copper conductors
• H DPE or FEP insulation
• Tightly twisted & unshielded
• CM rated, RoHS compliant
58
GOOD
DUAL SHIELD OUTSIDE PLANT RG6 FOR CATV & DBS FOR OUTDOOR & DIRECT BURIAL APPLICATIONS
QUAD SHIELD NON-PLENUM RG6 FOR CATV & DBS
QUADFLEX-BC
GOOD
• Cool Spool Reels
• Sweep Test to 3.0 GHz
• Excellent SRL ration
• 2 colors
• Solid bare copper conductors
• Foamed Polyethylene Insulation
• B onded foil & 60% aluminum braid shields
• B raid shield flooded for water repellant gel
QUADFLEX
• Cool Spool® Reels
• Sweep Tested to 3.0 GHz
• Excellent SRL ration
• 2 colors
IDEAL FOR MOST RF VIDEO APPLICATIONS
WHERE DC POWER IS NOT NEEDED
DUAL SHIELD PLENUM RG6 FOR CATV & DBS
RG6-BC-CATV-DB
GOOD
www.LibAV.com
|
BETTER
• W ooden spools
• Sweep Tested to 3.0 GHz
• Excellent SRL ratio
• B lack only
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
CABLES: RF COAXIAL SOLUTIONS
RG11-CATV
IDEAL FOR LONG RUN, LOW LOSS RF VIDEO APPLICATIONS
WHERE DC POWER IS NOT NEEDED
DUAL SHIELD NON-PLENUM RG11 FOR CATV & DBS
• Solid copper-clad steel center conductor
• Foamed Polyethylene Insulation
• Bonded foil and 60% aluminum braid shields
• NEC CM, CEC CMG FT4, RoHS compliant
RG11-P-CATV
• Solid copper-clad steel center conductor
• Foamed Polyethylene Insulation
• Bonded foil and 60% aluminum braid shields
• CMP, RoHS compliant
DUAL SHIELD OUTSIDE PLANT RG11 FOR CATV & DBS
QUAD SHIELD PLENUM RG11 FOR CATV & DBS
MATCHING UNIVERSAL CONNECTORS FOR ALL FORMATS
• Wooden spools
• Sweep Tested to 3.0 GHz
• Excellent SRL ratio
• White only
BEST
•W
ooden spools
• Sweep Tested to 3.0 GHz
• E xcellent SRL ratio
• B lack only
IDEAL FOR RF VIDEO NON-DC REQUIRED APPLICATIONS
WHERE EXTERNAL INTERFERENCE RESISTANCE IS NEEDED
• Solid copper-clad steel center conductor
• Foamed Polyethylene Insulation
• Two 100% foil and two braid shields 60/40%
• CMP, RoHS compliant
C-TEC2
BEST
IDEAL FOR ALL LONG RUN LOW LOSS RF VIDEO CABLE
FOR OUTDOOR AND DIRECT BURIAL APPLICATIONS
• Solid copper-clad steel center conductor
• Foamed Polyethylene Insulation
• Bonded foil and 60% aluminum braid shields
• Braid shield flooded for water repellent gel
RG11-QUAD-PL
• Wooden spools
• Sweep Tested to 3.0 GHz
• Excellent SRL ratio
• Black only
IDEAL FOR LONG RUN LOW LOSS RF VIDEO APPLICATIONS
WHERE DC POWER IS NOT NEEDED
DUAL SHIELD PLENUM RG11 FOR CATV & DBS
RG11-BC-CATV-DB
BEST
BEST
• Wooden spools
• Sweep Tested to 3.0 GHz
• Excellent SRL ratio
• White only
BEST
F PLUGS FOR ALL FORMATS
• Ferrule-less F & M series design allows any sized
cable constructions from virtually any manufacturer
to fit these connectors
• Significantly reduces the number of connectors
required to terminate a variety of cable types
• All-metal connectors with machined slots for ID bands
• Perfect for RF video–CATV, MATV, direct broadcast
satellite
• Super-simple termination process, see the video at
LibAV.com or scan the QR code below
C-TEC COMPLETE TOOL PACK
2
CM-TOOL-PAC
WATCH
IT NOW!
2
C-TEC TERMINATION
CHECK OUT OUR ENTIRE
VIDEO LIBRARY AT LIBAV.COM
TERMINATION SYSTEM
FOR RG59, RG6, RG11, MINI RGB & AUDIO CONNECTORS
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
|
800.530.8998
|
www.LibAV.com
59
CABLES: SERIAL DIGITAL SOLUTIONS
• SMPTE COMPLIANT FOR SD SIGNALS
• UL, CSA, AND ROHS COMPLIANT
• HIGH QUALITY LOW LOSS PRODUCT
• COMPETITIVE PRICING
• S DI, HD-SDI, 3G-SDI
•M
ATCHED CONNECTORS
• S WEEP TEST 4.5 GHZ
•P
LENUM AND NON-PLENUM
23-MINI-SD LIBERTY MINI-RG59 SERIAL DIGITAL HIGH RESOLUTION COAXIAL CABLE — IDEAL FOR SHORT LENGTH SDI RUNS & SDI PATCHING
GOOD
• 23 AWG solid bare copper center conductor
• 95% coverage tinned copper braid shield
• N itrogen injected cellular Polyethylene
• N EC rated rated CM, CEC rated CMG FT4
• Full Aluminum/Poly/Aluminum inner foil shield • Standard colors black & white
23-MINI-CMP LIBERTY MINI-RG59 SERIAL DIGITAL HIGH RESOLUTION COAXIAL CABLE — IDEAL FOR SHORT LENGTH PLENUM SDI RUNS & SDI PATCHING
GOOD
• 23 AWG solid bare copper center conductor
• 95% coverage tinned copper braid shield
• N itrogen injected cellular Fluoropolymer
• N EC rated CMP, CEC rated CMP FT6
• Full Aluminum/Poly/Aluminum inner foil shield • Standard colors black & white
20-CMR-VIDEO
LIBERTY RG59 SERIAL DIGITAL HIGH RESOLUTION COAXIAL RISER RATED CABLE — IDEAL FOR MEDIUM LENGTH SDI RUNS
BETTER
• 20 AWG solid bare copper center conductor
• 95% coverage tinned copper braid shield
• N itrogen injected cellular Fluoropolymer
• N EC rated CMR, CEC rated CMG FT4
• Full Aluminum/Poly/Aluminum inner foil shield • Standard colors black & white
20-CMP-VID-COAX LIBERTY RG59 SERIAL DIGITAL HIGH RESOLUTION COAXIAL, PLENUM RATED CABLE — IDEAL FOR MEDIUM LENGTH PLENUM SDI RUNS
BETTER
• 20 AWG solid bare copper center conductor
• 95% coverage tinned copper braid shield
• N itrogen injected cellular Fluoropolymer
• N EC rated CMP, CEC rated CMP FT6
• Full Aluminum/Poly/Aluminum inner foil shield • Standard colors black & white
18-CMR-SD
LIBERTY RG6 SERIAL DIGITAL HIGH RESOLUTION COAXIAL RISER RATED CABLE — IDEAL FOR MEDIUM LENGTH SDI RUNS
BEST
• 18 AWG solid bare copper center conductor
• 95% coverage tinned copper braid shield
• N itrogen injected cellular Fluoropolymer
• N EC rated CMR, CEC rated CMG FT4
• Full Aluminum/Poly/Aluminum inner foil shield • Standard colors black & white
18-CMP-VID-COAX
LIBERTY RG6 SERIAL DIGITAL HIGH RESOLUTION COAXIAL PLENUM RATED CABLE — IDEAL FOR MEDIUM LENGTH PLENUM SDI RUNS
BEST
• 18 AWG solid bare copper center conductor
• 95% coverage tinned copper braid shield
• N itrogen injected cellular Fluoropolymer
• N EC rated CMP, CEC rated CMP FT6
• Full Aluminum/Poly/Aluminum inner foil shield • Standard colors black & white
60
800.530.8998
|
www.LibAV.com
|
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
CABLES: SPEAKER CABLE SOLUTIONS
• UL, ETL, ROHS AND REACH
• MANY CHOICES FOR YOUR APPLICATION
• GOOD-BETTER-BEST IN MOST CATEGORIES
• COMPETITIVE PRICING
GENERAL PURPOSE RISER
• COOL SPOOL® REELS AND PAYOUT BOXES
• CUSTOM PRINTING, SPOOLING AND CUT
IDEAL FOR COMMERCIAL SOUND APPLICATIONS, TRADITIONAL AND 70 VOLT SYSTEMS
FEATURES
• 18, 16, 14 & 12 AWG 2 & 4 conductor
• 7, 19 or 29 strand annealed copper conductors
• Semi-Rigid PVC insulation for lower capacitance
• R iser rated PVC jacketing
• U L listed CMR or CL3R, Canada FT4, RoHS
• Cool Spool 1000ft put ups
18-2C
18-4C
16-2C
16-4C
14-2C
14-4C
GOOD
12-4C
12-2C
GENERAL PURPOSE PLENUM
IDEAL FOR COMMERCIAL SOUND APPLICATIONS, TRADITIONAL AND 70 VOLT SYSTEMS
FEATURES
• 16, 14 & 12 AWG 2 & 4 conductor
• 19 or 29 strand annealed copper conductors
• P lenum rated PVC insulation
• P lenum rated PVC jacketing
• U L listed CMP or CL3P, Canada FT6, RoHS
• Cool Spool 1000ft put ups
12-2C-P
TIGHT TUBE PLENUM ™ (TTP ™)
18-2C-P
18-4C-P
16-2C-P
16-4C-P
14-2C-P
14-4C-P
RUGGED HIGH QUALITY FOR SUPERIOR PERFORMANCE AND EASE OF INSTALLATION
• Stranded Annealed Bare Copper Conductors
• P lenum rated PVC Alloy insulation
• Twisted, unshielded
• P lenum rated PVC Jacket
• N EC CL3P, CEC CMP FT6, RoHS Compliant
• 1000 Foot Spools
16-2C-TTP
16-4C-TTP
10-2C-TTP
12-2C-TTP
14-2C-TTP
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
|
800.530.8998
|
www.LibAV.com
GOOD
BEST
61
CABLES: SPEAKER CABLE SOLUTIONS
• UL, ETL, ROHS AND REACH
• MANY CHOICES FOR YOUR APPLICATION
• GOOD-BETTER-BEST IN MOST CATEGORIES
• COMPETITIVE PRICING
HOMETRAX™
• COOL SPOOL® REELS AND PAYOUT BOXES
• COMPETITIVE PRICING
• CUSTOM PRINTING, SPOOLING AND CUTS
IDEAL FOR BUDGET CONSCIOUS INSTALLATIONS
16-2C-HT
FEATURES
14-2C-HT
GOOD
• 16 and 14 AWG 2 and 4 conductor
• 41 strand annealed copper conductors
• Semi-Rigid PVC insulation for lower capacitance
• Flame rated PVC jacketing
• UL listed CM or CL3, Canada FT4, RoHS
• Nested box packaging only
• White Jackets are standard
16-4C-HT
KNOCKOUT PLUS ™
16-2C-KO+
14-4C-HT
• 500 foot put ups
STRONGER & SMOOTHER THAN STANDARD
FEATURES
14-2C-KO+
BETTER
• 16 and 14 AWG 2 and 4 conductor
• 41 strand annealed copper conductors
• Semi-Rigid PVC insulation for lower capacitance
• 20% thicker Flame rated PVC jacketing
• Cool Spool Reels and Nested Boxes
• UL listed CM or CL3, Canada FT4, RoHS
• 500 or 1000 foot put ups
16-4C-KO+
EXTRAFLEX PLUS ™
16-4C-EX+
• Custom Colors available with a 10,000 minimum
14-4C-KO+
RUGGED HIGH QUALITY, SUPERIOR PERFORMANCE & EASE OF INSTALLATION
16-2C-EX+
FEATURES
BEST
• 16, 14, and 12 AWG one and two pair formats
• High strand rope lay annealed copper conductors
• Foamed Polyethylene insulation
• Very thick and strong pressured PVC jacketing
• Cool Spool Reels
• UL listed CMR or CL3R, Canada FT4, RoHS
• THX® Certified, white jackets
14-4C-EX+
14-2C-EX+
12-4C-EX+
12-2C-EX+
62
800.530.8998
• 500 and 1000 foot put ups
10-2C-EX+
|
www.LibAV.com
|
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
CABLES: SPEAKER CABLE SOLUTIONS
ULTRACAP ™
THX ® CERTIFIED SPEAKER CABLES FOR THE DISCERNING AUDIOPHILE
16-1P-UC
FEATURES
14-1P-UC
AWESOME
• 16, 14, and 12 AWG one and two pair formats
• High strand rope lay annealed copper conductors
• Foamed Polyethylene insulation
• Very thick and strong pressured PVC jacketing
• Cool Spool Reels
• UL listed CMR or CL3R, Canada FT4, RoHS
• THX® Certified, white jackets
• 500 and 1000 foot put ups
12-1P-UC
12-2P-UC
14-2C-TTP
2
Audio
connectors slip
on easily to the
speaker cable
conductor &
compress on
effortlessly with
the easy-to-use
2
Audio
crimp tools!
SPECIFICATIONS SUBJECT TO CHANGE
|
IMAGES NOT TO SCALE
|
800.530.8998
|
www.LibAV.com
Works with all
Liberty speaker
cable, for in-wall
& non in-wall
audio applications.
63
HEADQUARTERS
11675 Ridgeline Drive
Colorado Springs, Colorado
80921 USA
Phone: 719-260-0061
Fax: 719-260-0075
Toll-Free: 800-530-8998
Order E-Mail: [email protected]
EAST COAST OFFICE AND
WAREHOUSE FACILITY
5521 Lakeview Rd., Suite W
Charlotte, North Carolina
28269 USA
Phone: 719-260-0061
Fax: 719-260-0075
WESCO ASSEMBLY
2202 S 7th Street, Suite 120
Phoenix, Arizona
85034 USA
Phone: 602-226-1625
Toll-Free: 800-263-6591
Email: [email protected]
Toll-Free: 800-530-8998
Order E-Mail: [email protected]
L0262
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement