- Computers & electronics
- TVs & monitors
- Wall & ceiling mounts accessories
- Chief Manufacturing
- MSM
- Installation instructions
Chief Manufacturing MSM Installation instructions
Add to my manuals12 Pages
Chief Manufacturing MSM offers versatile TV mounting solutions for both wood stud and concrete walls. Its adjustable design allows for precise positioning of your TV, ensuring an optimal viewing experience. Whether you prefer a static upright position with the MSM or a tilted angle with the MTM, both models provide a secure and sturdy installation. With its heavy-duty construction, the MSM can support up to 125 lbs on dual studs and 75 lbs on a single stud, making it suitable for a wide range of TV sizes.
advertisement
I N S T A L L A T I O N I N S T R U C T I O N S
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
MSM MTM
FUSION MEDIUM HEIGHT ADJUST
FLAT PANEL MOUNTS
MSM/MTM Series
MSM/MTM Series
DISCLAIMER
Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING:
A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.
Installation Instructions
CAUTION:
A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions.
WARNING:
Failure to read, thoroughly understand, and follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installer’s responsibility to make sure all components are properly assembled and installed using the instructions provided.
WARNING:
Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the component.
WARNING:
Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight of all components located between the MSM/MTM up to (and including) the display does not exceed 125 lbs (56.7 kg) for dual stud attachment, and 75 lbs (34.0 kg) for single stud attachment.
2
Installation Instructions
DIMENSIONS
25.60
[650]
MAX HORIZONTAL SPACING
18.79
477.4
16.00
406.4
7.63
193.7
MSM/MTM Series
.50
[12.7]
UP/DOWN
ADJUSTMENT
EACH SIDE
.32
8.1
1.52
38.5
7.53
191.2
15.10
383.4
15.75
400
MAX
VERTICAL
SPACING
16.50
419.1
1.96
49.8
.35
8.9
MSM
13.53
343.7
6.00
152.4
1.00
25.4
1.75
44.5
RAILS SLIDE
LEFT/RIGHT
FOR STUD
OFFSET
.50
12.7
25.00
635
.33
8.3
1.00
25.4
26.25
[667]
MAX HORIZONTAL SPACING
18.79
477.4
16.00
406.4
7.63
193.7
13.53
343.7
6.00
152.4
1.00
25.4
1.75
44.5
RAILS SLIDE
LEFT/RIGHT
FOR STUD
OFFSET
.50
12.7
25.00
635
.33
8.3
1.00
25.4
MTM
.50
[12.7]
UP/DOWN
ADJUSTMENT
EACH SIDE
.32
8.1
2.00
50.8
7.53
191.2
15.10
383.4
15.75
[400]
MAX
VERTICAL
SPACING
.38
9.5
16.50
419
1.98
50.3
12°
MAX TILT
3
Installation Instructions
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
MSM/MTM Series
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
4
MSM/MTM Series
TOOLS REQUIRED FOR INSTALLATION
Installation Instructions
#2
7/32" (5.5mm) Wood Stud
5/16" (7.9mm) Concrete
PARTS
[Included with
MSM6XXX/MTM6XXX
Models Only]
Custom
MSM6XXX/
MTM6XXX
Hardware
B (1)
C (1)
A (1)
D (1)
E (1)
J (1) [Used on MSMU/MTMU Models Only]
(MSM Only)
F (1)
(MSM Only)
J1 (8)
M4x16mm
J2 (6) J3 (6)
M4x20mm M4x25mm
J4 (6) J5 (6)
M5x16mm M5x20mm
J6 (6)
M5x25mm
K (1)
(MTM Only)
G (1)
(MTM Only)
J7 (6)
M6x16mm
J8 (6)
M6x25mm
J9 (1)
M5
H (1)
3/16" - 6"
J10 (6)
M8x20mm
J11 (6)
M8x30mm
J12 (4)
M8x50mm
K1 (4)
5/16"
K2 (4)
5/16"
K3 (4)
5/16" x 2-1/2"
J13 (8)
.750x.323x.250
J14 (8)
.750x.344x.500
J15 (8)
5
MSM/MTM Series
INSTALLATION
The MTM and MSM have been designed to be mounted directly onto either a wood stud or concrete wall. The MTM has brackets which allow the TV to be tilted. The MSM has static brackets which keep the TV in an upright position.
Installation Instructions
4.
Measure up 7-1/2" from the center point to mark location of the upper mounting slots.
5.
Using a level, mark the wall on each stud to attach the mount through the upper mounting slots. (See Figure 2)
NOTE:
The MSM and MTM may be attached through the mounting slots on dual studs, or through the center mounting holes on a single stud. (See Figure 2)
Locate Mounting Site
5
WARNING:
IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY
OR DAMAGE TO EQUIPMENT! It is the installers responsibility to make certain the structure to which the mount is being attached is capable of supporting five times the weight of the MTM or MSM and all attached equipment not to exceed 125 lbs (56.7 kg) for dual stud attachment, and
75 lbs (34.0 kg) for single stud attachment.
NOTE:
Proceed to either the Installing to a Wood Stud Wall section or the Installing to a Concrete Wall section.
Installing to a Wood Stud Wall
1.
Determine the center of the TV screen, and where it should be located on the wall.
2.
Locate the closest stud to the left and right of the selected location.
NOTE:
If the screen area lies over a stud, use that stud if using the single stud installation method.
NOTE:
Use that stud and the stud to either the left or right of it if using the dual stud installation method.
3.
Line up the notches on mount with center of screen marking to determine vertical center. (See Figure 1)
Single Stud
Installation
5
Center of screen
7-1/2"
Vertical center of mount
Dual Stud
Installation
Figure 2
WARNING:
ELECTRICAL SHOCK HAZARD! CUTTING
OR DRILLING INTO ELECTRICAL CORDS OR CABLES
CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY!
ALWAYS make certain area behind mounting surface is free of electrical wires and cables before drilling or installing fasteners.
Figure 1
6
Installation Instructions
WARNING:
EXPLOSION AND FIRE HAZARD! CUTTING
OR DRILLING INTO GAS PLUMBING CAN CAUSE DEATH
OR SERIOUS PERSONAL INJURY! ALWAYS make certain area behind mounting surface is free of gas, water, waste, or any other plumbing before cutting, drilling, or installing fasteners.
Dual Stud
Installation
6 9
MSM/MTM Series
9.
Drill 7/32" pilot holes at markings for lower mounting holes.
(See Figure 3)
10. Use two 5/16 x 2-1/2" lag bolts (K3) and two 5/16" flat washers (K2) [one lag bolt and washer for single stud installation] to attach the mount to the wall through the lower mounting holes. (See Figure 3)
11. Slide rails to approximate center of screen location.
Installing to a Concrete Wall
1.
Determine the center of the TV screen, and where it should be located on the wall.
2.
Line up the notches on mount with center of screen marking to determine vertical center. (See Figure 1)
3.
Measure up 7-1/2" from the center point to mark location of the upper mounting slots. (See Figure 1)
4.
Using a level, mark the wall through both upper mounting slots. (See Figure 4)
7
(K3) x 2
10
(K3) x 2
(K2 x 4)
WARNING:
ELECTRICAL SHOCK HAZARD! CUTTING
OR DRILLING INTO ELECTRICAL CORDS OR CABLES
CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY!
ALWAYS make certain area behind mounting surface is free of electrical wires and cables before drilling or installing fasteners.
WARNING:
EXPLOSION AND FIRE HAZARD! CUTTING
OR DRILLING INTO GAS PLUMBING CAN CAUSE DEATH
OR SERIOUS PERSONAL INJURY! ALWAYS make certain area behind mounting surface is free of gas, water, waste, or any other plumbing before cutting, drilling, or installing fasteners.
6 9 x 2
(K2 x 2)
6
10 x 2
5
9
7 10
(K3) x 2
(K2 x 4)
Single Stud
Installation
7
11
(K3) x 2
Figure 3
6.
Drill one 7/32" pilot hole in each stud.
7.
Use two 5/16 x 2-1/2" lag bolts (K3) and two 5/16" flat washers (K2) [one lag bolt and washer for single stud installation] to attach top of mount to wall. (See Figure 3)
8.
Mark the attachment points for the lower mounting slots, making sure the attachment points are located on the studs.
(See Figure 3)
Figure 4
5.
Drill one 5/16" pilot hole at each marking.
6.
Install an anchor (K1) into each pilot hole using a hammer.
7.
Use two 5/16 x 2-1/2" lag bolts (K3) and two 5/16" flat washers (K2) to attach top of mount to anchors in wall.
7
MSM/MTM Series
8.
Mark the attachment points for the lower mounting slots.
(See Figure 4)
9.
Drill one pilot hole at each marking for lower mounting holes. (See Figure 4)
10. Install an anchor (K1) into each pilot hole using a hammer.
11. Use two 5/16 x 2-1/2" lag bolts (K3) and two 5/16" flat washers (K2) to attach the mount to the wall through the lower mounting holes. (See Figure 4)
12. Slide rails to approximate center of screen location.
Attaching Interface Brackets to TV
1.
Align the center of the bracket with center of screen.
(See Figure 5)
NOTE:
The diamond-shape hole in the bracket corresponds to the center of the mount.
Mounting
Slot 1
Knobs
Installation Instructions
Mounting
Holes
2
Figure 6
Pull strap
Center of bracket
Figure 5
WARNING:
IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Using screws of improper size may damage your display. Properly sized screws will easily and completely thread into display mounting holes. If spacers are required, be sure to use longer screws of the same diameter.
2.
Select correct screws, spacers (if necessary) and washers from the hardware bag and attach brackets to back of screen. (See Figure 5)
Switching Interface Brackets (Optional)
If an installation situation makes adjusting the location of interface brackets necessary, there are several options.
1.
The wall bracket may be adjusted side to side at the point of attachment (mounting slots for dual stud installation, mounting holes for single stud installation). (See Figure )
2.
The location of the left and right interface brackets may be switched, with the knobs on the MTM interface brackets facing the inside of the mount. (See Figure )
8
Installation Instructions
3d Center Line (CL)
MSM/MTM Series
3e
Pullstraps
NEVER place both interface brackets to one side of the wall mount center line (CL)!
Knobs to outside
of brackets
Figure 7
3.
If necessary, the tilt interface bracket knobs may be switched to allow the interface brackets to be reversed.
(See Figure 7) a. Remove display from mount.
b. Remove interface brackets from display.
c. Hold the right interface bracket horizontally, tightly gripping it so that spacers do not move.
d. Remove the knob, washer and screw.
e. Replace the knob, washer and screw in the opposite order, with the knob on the inside of the bracket.
f. Switch the right interface bracket to the left side of the wall mount.
g. Repeat Steps 3c through 3f with the left interface bracket.
Attaching Screen to Wall Mount
1.
Adjust Velcro® pull strap (if necessary) so it does not extend beyond bottom of screen. (See Figure 8)
NOTE:
Do NOT allow both interface brackets to be located on same side of wall bracket. (See Figure 8)
NOTE:
NEVER place both interface brackets to one side of the wall mount center line! (See Figure 8)
Both interface brackets must NEVER be located to one side of the wall bracket!
Figure 8
9
MSM/MTM Series
1
(H)
Raises screen
2
Installation Instructions
Lowers screen
Top
Hook
2
(Screen not shown for clarity)
Figure 10
Locking Mount (Optional)
1.
Add optional security bracket (F or G) to the mount.
(See Figure 11)
2.
Add padlock (not included) to complete security.
Pullstraps
5
(Screen not shown for clarity)
Figure 9
2.
Hang top hook of interface brackets onto the top bar of the mount. (See Figure 9)
NOTE:
The screen initially installs into the "kickstand mode" to allow easy cable access.
3.
Slide screen and bars to desired viewing position.
4.
Route cables between wall and bars.
CAUTION:
PINCH POINTS! Keep fingers, hands and cables out of pinch point areas.
5.
Pull downward on the pullstraps and swing inward toward wall, latching interface brackets to lower bar and locking bottom of screen to the mount. (See Figure 9)
Adjusting Roll/Height of Wall Brackets
NOTE:
The height adjust wall bracket allows adjustment of
+ 1/2".
1.
Turn to right (tighten) to raise side of screen.
(See Figure 10)
2.
Turn to left (loosen) to lower side of the screen.
(G)
(MTM Shown)
2
1
Figure 11
10
Installation Instructions MSM/MTM Series
11
MSM/MTM Series Installation Instructions
Chief Manufacturing, a division of
Milestone AV Technologies
8831-000024
2008 Milestone AV Technologies www.chiefmfg.com
09/08
USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378
P 800.582.6480 / 952.894.6280
Europe
F 877.894.6918 / 952.894.6918
A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
P +31 (0)40 2668620
Asia Pacific
F +31 (0)40 2668615
A Room 24F, Block D, Lily YinDu International Building
LuoGang, BuJi Town, Shenzhen, CHINA.
P +86-755-8996 9226
F +86-755-8996 9217
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project