Cisco Systems RNG200 Instruction Manual

Cisco Systems RNG200 Instruction Manual
Notice for CATV Installers
The servicing instructions in this notice are for use by qualified service personnel only. To reduce risk of
electric shock, do not perform any servicing other than that contained in the operating instructions, unless you
are qualified to do so.
Protect the Product from Lightning
For added protection, unplug this apparatus during lightning storms or when unused for long periods of
time. In addition to disconnecting the AC power from the wall outlet, disconnect the signal inputs.
Verify the Power Source from the On/Off Power Light
Note to System Installer
For this apparatus, the coaxial cable shield/screen shall be
grounded as close as practical to the point of entry of the cable
into the building.For products sold in the US and Canada, this
reminder is provided to call the system installer's attention to
Article 800-93 and Article 800-100 of the NEC (or Canadian
Electrical Code Part 1), which provides guidelines for proper
grounding of the coaxial cable shield.
When the on/off power light is not illuminated, the apparatus may still be connected to the power source.
The light goes out when the apparatus is turned off, regardless of whether it is still plugged into an AC power
source.
Eliminate AC Mains Overloads
WARNING
TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS UNIT TO RAIN OR MOISTURE.
This symbol is intended to alert you that uninsulated voltage
within this product may have sufficient magnitude to cause
electric shock.Therefore, it is dangerous to make any kind of
contact with any inside part of this product.
WARNING:
Avoid electric shock and fire hazard! Do not overload AC mains, outlets, extension cords,
or integral convenience receptacles. For products that require battery power or other
power sources to operate them, refer to the operating instructions for those products.
CAUTION: To reduce the risk of electric shock, do not
remove cover (or back). No user-serviceable parts
inside. Refer servicing to qualified service personnel.
Explorer RNG 200 DVR
with M-Card Interface
®
Prevent Power Cord Damage
Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles,
and the point where the cord exits from the apparatus.
•
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
•
Do not place this apparatus on a bed, sofa, rug, or similar surface.
Ce symbole a pour but de vous avertir qu’une
documentation importante sur le fonctionnement et
l’entretien accompagne ce produit.
•
Do not place this apparatus on an unstable surface.
•
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
•
Do not install this apparatus in an enclosure, such as a bookcase or rack, unless the installation
provides proper ventilation.
IMPORTANT SAFETY INSTRUCTIONS
•
Do not place entertainment devices (such as VCRs or DVDs), lamps, books, vases with liquids, or
other objects on top of this product.
Read These Instructions
Protect from Exposure to Moisture and Foreign Objects
Keep These Instructions
Do not use this apparatus near water.
20070131 SysInstaller 820 US/Canada/Intl
Heed All Warnings
™
™
Provide Ventilation and Select a Location
This symbol is intended to alert you of the presence
of important operating and maintenance (servicing)
instructions in the literature accompanying this product.
Ce symbole a pour but d’alerter toute personne qu’un contact
avec une pièce interne de ce produit, sous tension et non isolée,
pourrait être suffisant pour provoquer un choc électrique. Il est
donc dangereux d’être en contact avec toute pièce interne de
ce produit.
Connecting the
WARNING:
Avoid electric shock and fire hazard! Do not expose this product to liquids, rain, or
moisture.
Follow All Instructions
Power Source Warning
A label on this product indicates the correct power source for this product. Operate this product only from
an electrical outlet with the voltage and frequency indicated on the product label. If you are uncertain of the
type of power supply to your home or business, consult your service provider or your local power
company.
WARNING:
Avoid electric shock! Unplug this product before cleaning. Clean only with a dry cloth.
Do not use a liquid cleaner or an aerosol cleaner. Do not use a magnetic/static cleaning
device (dust remover) to clean this product.
Ground the Product
WARNING:
Avoid electric shock and fire hazard! Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two blades with one wider than the other.
A grounding-type plug has two blades and a third grounding prong. The wide blade or
the third prong is provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
If this product connects to coaxial cable wiring, be sure the cable system is grounded (earthed). Grounding
provides some protection against voltage surges and built-up static charges.
Outdoor Grounding System
If this product connects to an outdoor antenna or cable system, be sure the antenna or cable system is
grounded (earthed). This provides some protection against voltage surges and built-up static charges.
Article 810 of the National Electric Code (NEC) ANSI/NFPA No. 70-1990, provides the following
information:
•
Grounding of the mast and supporting structure
•
Grounding the lead-in wire to an antenna discharge unit
•
Size of the grounding conductors
•
Location of the antenna-discharge unit
•
Connection to grounding electrodes
•
Requirements for the grounding electrodes (see the following antenna grounding diagram as
recommended by NEC ANSI/NFPA 70)
WARNING:
To avoid electric shock, do not locate an outside antenna system in the vicinity of
overhead power lines or power circuits. Touching power lines or circuits might be
fatal.
WARNING:
Avoid electric shock and fire hazard! Never push objects through the openings in this
product. Foreign objects can cause electrical shorts that can result in electric shock or
fire.
Accessories Warning
WARNING:
Avoid potential for electric shock or fire. Only use attachments/accessories specified
by your service provider or the manufacturer.
Service Warnings
WARNING:
Avoid electric shock! Do not open the cover of this product. Opening or removing the
cover may expose you to dangerous voltages. If you open the cover, your warranty will
be void. This product contains no user-serviceable parts. Refer all servicing to qualified
service personnel.
Unplug this product and then obtain service when the product has been damaged in any way, such as when
the power-supply cord or plug is damaged, when liquid has been spilled or objects have fallen into the
product, when the product has been exposed to rain or moisture, when the product has been dropped, and
when the product does not operate normally. Adjust only those controls that are covered by the operating
instructions as improper adjustment could result in damage and may require extensive work by a qualified
technician to restore the product to its normal operation.
Check Product Safety
Upon completion of any service or repairs to this product, the service technician must perform safety
checks to determine that this product is in proper operating condition.
Protect the Product when Moving It
Always disconnect the power source when moving the apparatus or connecting or disconnecting cables.
Example Of Antenna Grounding
Antenna Lead In Wire
WARNING:
Avoid personal injury and damage to this product! Use only with the cart, stand, tripod,
bracket, or table specified by the manufacturer or sold with the apparatus. When a cart
is used, use caution when moving the cart/apparatus combination to avoid injury from
tip-over.
Compliance Information
United States FCC Compliance
Canada EMI Regulation
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against such
interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy. If not installed and used in accordance with the instructions, it may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does harmful interference to radio or television reception,
which can be determined by turning the equipment OFF and ON, the user is encouraged to try to correct
the interference by one or more of the following measures:
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la class B
est conforme à la norme NMB-003 du Canada.
•
Reorient or relocate the receiving antenna, if applicable
•
Increase the separation between the equipment and receiver
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected
•
Consult the cable company or an experienced radio/television technician for help
Any changes or modifications not expressly approved by Scientific-Atlanta, Inc., could void the user’s
authority to operate the equipment.
The information shown in the FCC Declaration of Conformity paragraph below is a requirement of the
FCC and is intended to supply you with information regarding the FCC approval of this device. The
phone numbers listed are for FCC-related questions only and not intended for questions regarding the
connection or operation for this device. Please contact your cable service provider for any questions you
may have regarding the operation or installation of this device.
FCC Declaration of Conformity
Ground Clamps
20070320 Set-Top Cable US & Canada
Antenna Discharge Unit
(NEC Section 810-20)
Electric Service
Equipment
Grounding Conductors
(NEC Section 810 -21)
Grounding Clamps
NEC = National Electrical Code
Power Service Grounding Electrode System
(NEC Art 250, Part H)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and 2) this device must accept any interference
received, including interference that may cause undesired operation.
20060628 FCC Standard
Disclaimer
Scientific-Atlanta, Inc. assumes no responsibility for errors or omissions that may appear in this guide.
Scientific-Atlanta reserves the right to change this guide at any time without notice.
AVC Video License
THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THE
PERSONAL AND NON-COMMERCIAL USE OF A CONSUMER TO (i) ENCODE VIDEO IN
COMPLIANCE WITH THE AVC STANDARD (“AVC VIDEO”) AND/OR (ii) DECODE AVC VIDEO THAT
WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND NON-COMMERCIAL ACTIVITY
AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSE TO PROVIDE AVC VIDEO. NO
LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL INFORMATION
MAY BE OBTAINDED FROM MPEG LA. L..L..C. SEE http://www.mpegla.com.
Scientific Atlanta, A Cisco Company
770.236.5000
5030 Sugarloaf Parkway, Box 465447
Lawrenceville, GA 30042
www.scientificatlanta.com
Scientific Atlanta and Explorer are registered trademarks of Scientific-Atlanta, Inc.
RNG 200 is a trademark of Scientific-Atlanta, Inc.
Cisco, Cisco Systems, and the Cisco Systems logo are registered trademarks of Cisco Systems, Inc. and/or
its affiliates in the U.S. and certain other countries.
CableCARD and M-Card are trademarks of Cable Television Laboratories, Inc.
®
™
Explorer RNG 200 Digital Video Recorder
Model: RNG 200
Manufactured by: Scientific-Atlanta, Inc.
5030 Sugarloaf Parkway
Lawrenceville, Georgia 30044 USA
Telephone 770-236-1077
Manufactured under license from Dolby Laboratories.
”Dolby” and the double-D symbol are registered trademarks of Dolby Laboratories.
HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of
HDMI Licensing LLC.
All other trademarks shown are trademarks of their respective owners.
Product and service availability is subject to change without notice.
© 2007 Scientific-Atlanta, Inc. All rights reserved. Printed in United States of America
May 2007
Part Number 4012607 Rev B
Welcome!
Explorer RNG 200 DVR Front Panel
Explorer RNG 200 DVR Back Panel
The Explorer® RNG 200™ DVR with a Multi-Stream
CableCARD™ (M-Card™) interface (DVR) receives and
displays digital signals, and it delivers programs in
exceptional picture and audio quality. Through the
DVR, you can also access interactive services such as
video-on-demand and pay- per-view programs.
Contact your service provider for information about
these and other available services. Use the
instructions in this guide to install the DVR and to
access your program services.
Safety First
Before using this DVR, read the IMPORTANT
SAFETY INSTRUCTIONS section of this guide.
Explorer eClub
The online Explorer eClub provides news and
information about consumer products. You can access
the Explorer eClub on the Internet at the following Web
address: www.scientificatlanta.com/explorerclub
1
2
3
4
5
6
7
8
9
1
T13031
2
3
4
5 6 7 8 9 10 11
12
13 14 15 16 17 18
T13032
1
Power
Turns the DVR on and off
1
Cable In
Connects to a coaxial cable that delivers the signal from your service provider
2
1394
Connects to display devices equipped with a 1394 input
2
Y/Pb/Pr
Connects the DVR to the component video input (Y/Pb/Pr) on the HDTV
3
USB Port
Connector reserved for future use
3
4
LED Indicators
Displays the following set-top status indicators:
• Data – Indicates data transfer status (Yellow LED)
• Remote – Indicates remote control activity (Green LED)
• Record – Indicates that a recording is in progress (Red LED)
Audio Out
(Left, Right)
Connects to RCA cables that send analog audio signals (left and right) to the stereo inputs
on an HDTV
4
Out 2 (Secondary Connects to either a VCR for archiving saved content from the DVR or connects to another
Video/Audio Out) set of inputs (composite) on your TV
5
S-Video Out
Connects to an S-Video cable that sends an S-Video signal to your TV or VCR. This signal
is standard-definition, but higher quality than other SDTV connections
5
LED Display
Displays the selected channel number and time of day
Watch TV
6
IR Sensor
Receives the infrared signal from the remote control
6
IR
Connector reserved for future use
Press the following remote control keys to access
services and programs:
7
Arrow Keys
Accesses on-screen services such as the on-screen guide, video-on-demand, or pay-per-view
7
8
Enter
Provides access to your on-screen selection
Dolby® Digital
Out (Optical)
Connects an optical cable to send a digital audio signal to a surround-sound receiver or
other digital audio device
• Guide – Display the on-screen program guide
9
Menu
Accesses the on-screen menu
8
Dolby Digital
Out (Coaxial)
Connects an RCA cable to send a digital audio signal to a surround-sound receiver or other
digital audio device
9
Cable Out
Connects to a coaxial cable that sends analog audio and video signals to a TV or VCR.
These signals are standard-definition TV (SDTV) video and stereo audio
• Arrows – Highlight a program in the schedule
• Info – Display a program description
• Select – Watch a specific program in the guide
Connecting the Explorer RNG 200 DVR
Performance Tips
If the DVR does not perform as expected, the
following tips may help. If you need further assistance,
contact your service provider.
10
M-Card Interface Slot for M-Card module, which decrypts subscription digital channels. Obtain an M-Card
module from your service provider
11
Security
Connector reserved for future use
12
HDMI
Connects the HDTV HDMI™ connector to the HDMI port. HDMI supports both digital audio
and video. May be used to connect to a DVI interface using an adaptor for video and
separate audio connections. You can use any of the following audio connections: Dolby
Digital Out [Coaxial] (8), Audio Out [LEFT and RIGHT] (3), or Dolby Digital Out [Optical] (7)
13
eSATA
Connects to an external Serial ATA (eSATA) hard disk drive for expanded drive space. (An
eSATA drive is not an archival device.) Check with your service provider for a list of approved
hard drive models for use with the DVR
14
1394
Connects to display devices equipped with a 1394 input
15
USB Port
Connector reserved for future use
16
Ethernet
Connector reserved for future use
17
AC Power
Connects to the power cord to deliver power to the DVR
18
AC Outlet
Connects to the AC power cord from another device, such as an HDTV
No Picture
• Verify that the power to your TV is turned on.
• If the DVR is plugged into a wall switch, verify that
the switch is in the ON position. (Avoid plugging the
DVR into an outlet that is controlled by a wall
switch.)
Cable
Input
• Verify that all cables are properly connected.
• The current channel may not be available in your
service package. Try selecting another channel to
see if a picture appears.
No Color
R
VIDEO
Y
VIDEO
L/
MONO
AUDIO
WARNING: Electric shock hazard! Unplug
all electronic devices before connecting or
disconnecting any device cables to the
receiver.
Back of
HDTV
AUDIO IN
DVI/HDCP
S-VIDEO
PB
L
PR
AUDIO
L
Y
L/
MONO
PB
L
R
PR
AUDIO
R
R
R
HD 1
IN
HD 2
IN
OUT
IN
T13033
• Verify that the TV program is broadcast in color.
• Adjust the TV color controls.
1. Connect the DVR to the HDTV as shown in the diagram.
No Sound
2. Connect the DVR to the coaxial cable coming from the
wall.
• If your setup includes a VCR or stereo, verify that
you have properly connected them to the DVR.
• Verify that the volume is turned up.
• Verify that the mute function is not on.
3. Plug the DVR and HDTV into an AC power source.
Important! Do not press the Power key on the DVR yet.
4. Wait for the time to appear on the LED display.
Important! Wait 2 to 3 minutes for the DVR to be
updated with the latest programming and service
information. When the front panel displays the time,
the update is complete.
5. Press the Power key on the DVR.
6. Turn on the power to your HDTV, and set the input channel
assigned by your service provider (channel 3 or 4).
U.S. Patents
A patent notice is affixed to this product. In addition, this product could be covered by one or more of the following patents.
4,498,169, 4,692,919, 4,748,667; 4,829,569; 4,866,770; 4,885,775; 4,888,799; 4,890,319; 4,922,456; 4,922,532; 4,924,498; 4,965,534; 4,991,011; 5,003,384; 5,012,510; 5,029,207; 5,045,816; 5,053,883;
5,054,071; 5,058,160; 5,142,575; 5,142,690; 5,146,526; 5,155,590; 5,214,390; 5,225,902; 5,225,925; 5,235,619; 5,237,610; 5,239,540; 5,241,610; 5,247,364; 5,255,086; 5,257,403; 5,267,071; 5,270,809;
5,271,041; 5,272,752; 5,282,028; 5,285,497; 5,287,351; 5,301,028; 5,309,514; 5,317,391; 5,319,709; 5,341,425; 5,347,388; 5,347,389; 5,357,276; 5,359,601; 5,361,156; 5,367,571; 5,379,141; 5,379,145;
5,381,481; 5,390,337; 5,400,401; 5,406,558; 5,418,782; 5,420,866; 5,420,923; 5,425,101; 5,428,404; 5,430,568; 5,434,610; 5,436,749; 5,438,370; 5,440,632; 5,442,472; 5,455,570; 5,457,701; 5,471,492;
5,477,199; 5,477,262; 5,477,282 5,477,370; 5,481,389; 5,481,542; 5,485,221; 5,493,339; 5,497,187; 5,500,758; 5,502,499; 5,506,904; 5,519,780; 5,539,822; 5,550,825; 5,579,055; 5,579,057; 5,583,562;
5,592,551; 5,596,606; 5,600,378; 5,602,933; 5,640,388; 5,657,414; 5,675,575; 5,684,876; 5,715,515; 5,724,525; 5,734,822; 5,740,300; 5,742,677; 5,754,940; 5,757,416; 5,771,064; 5,774,859; 5,825,829;
5,826,167; 5,850,305; 5,854,703; 5,870,474; 5,892,607; 5,920,626; 5,923,755; 5,930,024; 5,930,515; 5,937,067; 5,963,352; 5,966,163; 5,982,424; 5,991,139; 5,999,207; 6,005,631; 6,005,938; 6,016,163;
6,028,941; 6,029,046; 6,052,384; 6,055,244; 6,072,532; 6,105,134; 6,148,039; 6,157,719; 6,188,729; 6,195,389; 6,212,278; 6,215,530; 6,219,358; 6,240,103; 6,243,145; 6,246,767; 6,252,964; 6,272,226;
6,292,081; 6,292,568; 6,320,131; 6,374,275; 6,405,239; 6,411,602; 6,417,949; 6,424,714; 6,424,717; 6,433,906; 6,438,139; 6,463,586; 6,467,091; 6,476,878; 6,493,876; 6,510,519; 6,516,002; 6,516,412;
6,526,508; 6,538,595; 6,546,013; 6,560,340; 6,567,118; 6,570,888; 6,622,308; 6,629,227; 6,664,984; 6,667,994; 6,671,879; 6,674,967; 6,678,891; 6,714,598; 6,721,352; 6,721,956; 6,725,459; 6,738,982;
6,744,892; 6,744,967; 6,751,271; 6,760,918; 6,795,972; 6,802,077; 6,804,708; 6,811,447; 6,817,028; 6,822,972; 6,823,385; 6,832,386; 6,845,106; 6,868,473; 6,874,075; 6,889,191; 6,909,471; 6,917,622;
6,917,628; 6,922,412; 6,927,806; 6,928,656; 6,931,058; 6,937,729; 6,969,279; 6,971,008; 6,971,121; 6,978,310; 6,986,156; 6,988,900; 6,996,838; 7,010,801; 7,053,960; 7,065,213; 7,069,578; 7,069572;
D348065; D354959; D359737; D363932; D390217; D434753; D507240; D507535; D513407; D516518; RE36368; RE36988
20070417 Patents
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement