contents - i3 International

contents - i3 International
License Plate Capture Camera
Instruction Manual
CONTENTS
SAFETY INFORMATION.....................................................
PART DESCRIPTION & DIMENSION.....................................
MOUNTING & INSTALLATION INSTRUCTION........................
SPECIFICATION................................................................
1
3
5
10
Before attempting to connect or operate this product, please read these
instructions carefully and save this manual for future use.
SAFETY INFORMATION
Safety Information:
1. Read this Instruction Manual:
Before using the product, please carefully read through the
safety information and operation instructions.
2. Keep this Instruction Manual:
Safely store the Instruction Manual for future reference.
3. Follow instructions:
When operating the unit, please follow instructions on the
Instruction Manual.
4. Cleaning:
Before cleaning the unit, please first unplug the power.
5. Peripheral/accessories:
Do not place the unit on an unstable cart, tripod, or on a
tabletop as personal injury and damage to the unit may occur
due to a fall. Please use officially certified support, frames, and
accessories included with the product. Follow the instructions in
this Instruction Manual during installation to ensure the quality
and maintain safety.
6. Power:
Please follow the labeled specifications on the unit and
supply with the correct power. If unsure of the actual power
requirements, please contact the distributor and do not connect
the power at will.
7. Power cable:
The power cable must be properly secured as improper
connections may cause a short circuit, fire hazards, or serious
damage and hazards.
8. Lightning strike:
During prolonged inactivity, please unplug the power cable and
the video cable to avoid damage from lightning strike and power
surges.
9. Foreign objects and fluids:
Please do not insert any objects into the unit or spill liquids to
avoid short circuits.
10. Warning:
High voltage circuitry contained within the unit. Do not
disassemble to avoid electric shock. All maintenance operations
must be handled by qualified maintenance staff.
1
SAFETY INFORMATION
11. Maintenance:
When the following occurs, please first power off the unit and
then perform maintenance by qualified maintenance staff:
(a). Damaged power cable or socket
(b). Liquid spills or foreign objects in the unit
(c). Inoperable unit when proper instructions are followed
(d). Dropped unit or damaged shell
(e). Other anomalies
12. Component replacement:
Replaced components by the maintenance staff must be official
certified parts of identical specifications. Using unauthorized
components can cause fire hazards and electric shock damage.
13. Safety inspection:
After the unit maintenance has been completed, the maintenance
staff must perform safety inspection to ensure proper operation.
The triangle symbol with lightning arrow indicates
that ungrounded “Hazardous Voltage” exists within
the unit. The voltage level may cause personal
electric shock hazards.
The triangle symbol with exclamation mark
indicates that there are important operation and
maintenance instructions in the Instruction Manual.
2
PART DESCRIPTION & DIMENSION
Structure Illustration:
Raing Guard
Extendable Sunshield
Power connector
BNC connector
Mount adjustment
Partial enlargement
Tele/Wide adjustment screw
Far/Near adjustment screw
BLC adjustment
DC level adjustment
• Rain guard/extendable sunshield: minimize the effects of rain and
sunlight on image quality.
• Tele/Wide and Far/Near adjustment screws: lens adjustment
• Mount adjustment: easy to mount at different angles
• BNC connector: video output
• Power connector: DC12V/AC24V
• BLC adjustment: to adjust brightness for black light compensation
• DC level adjustment: to adjust lens aperture level according to the
lighting conditions.
3
PART DESCRIPTION & DIMENSION
Dimension and Accessory
4
MOUNTING & INSTALLATION INSTRUCTION
Please follow the mounting specification to install the SCR506 camera.
Package Content
Item
i3R506 camera
rubber pad
3 insulation tubes
guide pattern sticker
3 self-tapping screws
3 plastic anchor
printed material
Description
assembly camera
static electricity protection
static electricity protection
for marking hole easily
for mounting
for cement ceiling mounting
installation guide, notice card
Mounting Specification
1. Use appropriate screws and select an appropriate
location to install the camera.
2. Ensure the mounting surface can support to carry the
weight of the camera.
3. Suggest the width of the license plate covers
approximately 17-20% of the width of the screen
when used in conjunction with external License Plate
Recognition (LPR) software. Please make sure the
range between the camera and the license plate is
between 3 and 8 meters for optimal view when the
camera is used in combination with external LPR
software.
4. Suggest the camera stand height is more than 90 cm.
5. Suggest the vertical angle is less than 40 degree.
5
MOUNTING & INSTALLATION INSTRUCTION
6. Suggest the horizontal angle is less than 40 degree.
This camera is designed to cover only one lane (less
than 3 meters).
7. If work with DVR, make sure your DVR has the
de-interlace feature and the frame rate is above 15
fps for optimal effect.
8. To ensure an optimal view, please adjust the lens
under the limitation we suggest.
6
MOUNTING & INSTALLATION INSTRUCTION
Camera Installation
1. Mark hole positions: use the guide pattern sticker
to mark hole positions on the desired location. If you
want to mount the camera on the cement ceiling,
insert the plastic anchor into holes which you drill on
the cement ceiling first.
2. Adjust a mounting angle: loosen the left and right
screws first and then rotate the angle for mounting.
Finally, fasten the screws and rotate the mount
adjustment clockwise to fix the desired angle.
Partial Enlargemen
2. loosen the right screw
3. rotate the mount adjustment
1. loosen the left screw
7
MOUNTING & INSTALLATION INSTRUCTION
3. Install the camera: use an appropriate tool to
lock 3 self-trapping screws to fasten the camera.
For static electricity protection, please use the
rubber pad to cover the metal mount adjustment
and put 3 insulation caps through the metal
screws when locking 3 self-trapping screws into
the desired location.
Rubber Pad
Insulation Tube
Self-trapping Screw
4. Adjust the lens: loosen the Tele/Wide or Far/
Near screw counterclockwise and then\ adjust
it according to your needs. After adjustment, be
sure to lock it tightly to prevent water leaking into
the body of the camera.
Warning: please do not adjust
the Tele/Wide or Far/Near screw
out of the instruction line to avoid
damage to the lens.
8
MOUNTING & INSTALLATION INSTRUCTION
5. Adjust the BLC/DC function: loosen the BLC
screw. Use an appropriate tool to push the BLC
function up or down (on or off). Loosen the DC
screw and use an appropriate tool to rotate the
DC function for high or low level.
Use an appropriate tool to
loosen the BLC screw.
Loosen the DC
screw to adjust the
DC level function.
Use an appropriate tool
to rotate the screw for
high or low level
Use an appropriate tool
to push the BLC button
up or down (on or off)
6. A d j u s t t h e s u n s h i e l d : l o o s e n t h e s c r e w
counterclockwise, move the sunshield forward
or backward and then turn the screw clockwise
to fix the position of the sunshield. Be sure to
adjust the sunshield in coordination with the lens
to avoid sunshade problem.
Move forward/backward
9
SPECIFICATION
Image System
Signal system
Image Sensor
Effective pixels(HxV)
Electric
Scanning system
Sync system
Horizontal resolution
Built-in lens
Day & Night Mode
View angle
Gamma correction
Minimum illumination
Protection class
PAL
1/3" SONY CCD
768 x 494
752 x 582
2:1 Interlace V: 59.94Hz,
H: 15.734KHz
2:1 Interlace V: 50Hz,
H: 15.625KHz
Internal
540 TV lines (color)/ 600 TV lines (B/W)
f=9mm ~ 22mm, F1.4 DC iris varifocal IR-corrected lens
External adjustments (zoom and focus )
Yes(Mechanical ICR Filter)
Horizontal: 32.1°(wide) ~ 13.1°(tele)
Vertical: 23.3°(wide) ~ 9.8°(tele)
0.45
IR LED OFF: 0.015 lux (F1.4, AGC on, 10 IRE); 0.3lux (F1.4, AGC on, 50 IRE)
IR LED ON: 0lux
More than 50dB (AGC off)
Auto
Auto:(2500°K~9500°K)
Auto(Center Weighting)
1Vpp composite output, 75 ohm
Super power LED 36pcs
850nm
Non-Reflective
Reflective
15 Meter (50 ft.)
3~8 Meter (10~27 ft.)
up to 30 km/h (16 mph)
Under 10 lux by photocell auto controlled
More than 10,000 hours (50ºC/122ºF)
DC12V/AC24V
10W (max.)
7W (max.)
-10ºC ~ 50ºC (13.9ºF ~122ºF)
30 ~ 90% RH
-20ºC ~ 60ºC (-4ºF~140ºF)
ø83mmx205mm (ø3.26" x 8.09")
610g (1.35 lb)
Sunshield ; Cable management bracket
Compact die-cast aluminum ; Tempered Glass
IP66 ; Vandal-resistance
10
NOTE:The specification is subject to change without notice.
S/N ratio
Gain control
White balance
BLC
Video output
IR LED
IR wavelength
Plate Capture
IR distance
Capture range
Capture speed
IR turn on status
LED life
Power supply
Power requirement
Power consumption
Environment
Operating temperature
Operating humidity
Storage temperature
Mechanism
Dimensions(øxH)
Weight
Construction
NTSC
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement