Coleman 100-RANG Assembly and Operating Instructions

Add to My manuals
2 Pages

advertisement

Coleman 100-RANG Assembly and Operating Instructions | Manualzz

SCHEU PRODUCTS COMPANY, INCORPORATED

Mail: P.O. Box 250, Upland, CA 9l785

Plant: 8855 Baker Ave., Rancho Cucamonga, CA 91730

Telephone: 909-981-5343

ASSEMBLY AND OPERATING INSTRUCTIONS

MODELS 100-RANG/SPC-100RANG

CONSTRUCTION HEATER

YOUR SAFETY IS IMPORTANT TO YOU AND TO

OTHERS, SO PLEASE READ THESE INSTRUCTIONS

BEFORE YOU OPERATE THIS HEATER.

GENERAL HAZARD WARNING:

FAILURE TO COMPLY WITH THE PRECAUTIONS

AND INSTRUCTIONS PROVIDED WITH THIS HEATER,

CAN RESULT IN DEATH, SERIOUS BODILY INJURY

AND PROPERTY LOSS OR DAMAGE FROM HAZARDS

OF FIRE, EXPLOSION, BURN, ASPHYXIATION, AND

CARBON MONOXIDE POISONING.

ONLY PERSONS WHO CAN UNDERSTAND AND

FOLLOW

THE INSTRUCTIONS SHOULD USE OR SERVICE THIS

HEATER.

IF YOU NEED ASSISTANCE OR HEATER INFORMATION

SUCH AS AN INSTRUCTIONS MANUAL, LABELS, ETC.

CONTACT THE MANUFACTURER.

WARNING: FIRE, BURN, INHALATION,

AND EXPLOSION HAZARD. KEEP SOLID

COMBUSTIBLES, SUCH AS BUILDING MATERIALS,

PAPER OR CARDBOARD, A SAFE DISTANCE AWAY

FROM THE HEATER AS RECOMMENDED BY THE

INSTRUCTIONS. NEVER USE THE HEATER IN SPACES

WHICH DO OR MAY CONTAIN VOLATILE OR AIRBORNE

COMBUSTIBLES, OR PRODUCTS SUCH AS GASOLINE,

SOLVENTS, PAINT THINNER, DUST PARTICLES OR

UNKNOWN CHEMICALS.

OPERATING INFORMATION

Intended use is primarily the temporary heating of buildings under construction, alteration or repair.

WARNING

NOT FOR HOME OR RECREATIONAL VEHICLE USE.

SAFETY PRECAUTIONS

1. Check the heater thoroughly for damage. DO NOT operate a damaged heater.

2. DO NOT modify the heater or operate a heater which has been modified from its original condition.

3. Provide at least 5" W.C. but not over 1/2 psig to the heater inlet.

4. Use an appropriate hose or flexible connector not over

10 ft. in length.

5. Operate the heater only with the 4" W.C. regulator provided by the factory.

6. For indoor use only. Area must be well ventilated.

Provide minimum openings, of 2 sq. ft. near the floor and 2 sq. ft. near the ceiling.

7. If at any time gas odor is detected, IMMEDIATELY

DISCONTINUE operation until the source of gas has been located and corrected.

8. Install the heater such that it is not directly exposed to water spray, rain and/or dripping water or wind.

9. Maintain minimum clearance from normal combustible materials of 6 feet in all directions. Locate 10 ft. from canvas tarpaulins or similar coverings and secure them to prevent flapping or movement due to wind action.

10. Operate only on a stable, level surface.

11. Since permanent skin tissue damage can occur, avoid contact with the unit while is is operating or shortly after it has been shut off.

12. Do not use on combustible floors.

13. Do not move, handle or service while hot or burning.

14. Use only in accordance with local codes.

15. Installation of this natural gas heater must conform with local codes or, in the absence of local codes, with the

National Fuel gas Code ANSI Z223.1NFPA 54

PREPARING FOR OPERATION

1. Check the heater for possible shipping damage. If any is found, immediately notify your dealer.

2. Follow all of the "Safety Precautions."

3. Install plumbing to a low pressure (1/2 psig maximum) source of natural gas, using a minimum 3/4" i.d. hose or flexible connector not over 10 feet in length.

4. Connect the hose to the heater at the 1/2" SAE flare fitting at the inlet.

5. Securely tighten all gas connections.

6. Open the gas cock and check all gas connections with a

START

1. Fully open the gas cock at the natural gas source.

2. Place control knob of the safety pilot valve in pilot position and depress the knob admitting gas to pilot.

Push and release the piezo button until the pilot lights, multiple tries may be necessary. Alternately place a lighted match near the pilot (pilot is above cutout in the middle pan). If hose is filled with air, allow a few minutes for gas to reach the pilot.

3. When the pilot lights, continue to hold the button on the safety pilot valve depressed for 30 seconds, then release.

4. If the pilot goes out, wait 5 minutes and repeat the start procedure.

5. When the pilot remains lit, turn the knob left 1/4 turn to the "ON" position and the main burner will light.

CAUTION: INADEQUATE FUEL SUPPLY or lowering burn rate can cause sooting.

STOP

1. Securely close the gas cock at the gas source.

2. Depress the control knob of the pilot valve and turn clockwise to "OFF" position.

RESTART AFTER SAFETY SHUTDOWN

1. Securely close gas cock at the gas source.

2. Wait 5 minutes.

3. Restart following "Start" procedure.

ANSI Z83.7b-1993/CGA 2.14-1972

Construction Heater

SCHEU PRODUCTS COMPANY, INC.

P.O. BOX 5050

UPLAND, CA 91785-5050

MODEL 100-RANG/SPC-100RANG

TYPE OF GAS ................................. Natural Gas

INPUT RATING ........................... 100,000 BTU/hr

MANIFOLD PRESSURE ............ 4" Water Column

MAX. GAS SUPPLY PRESSURE .............. 1/2 psi

MIN. GAS SUPPLY PRESSURE ............... 5" W.C.

Part

Item No.

1 0814

2 3095

3 1074

4 6113

5 1510

6 1072

7 7616

8 6067

9 1837

10 6137

11 6234

* 7290

13 1594

14 3683

15 1098

Description

Base Assembly

Ballast

Valve Shield Assembly

Orifice, #55 Drill

Pilot Assembly

Manifold Assembly

Thermoelectric Valve

Spacer, 5/16" id x 1/2"

Pilot Tube Assembly

Fitting, Female Elbow

Thermocouple, 16"

Manual, Operating Instructions

Bracket, Pilot Mounting Assembly

Floor Shield Assembly

Emitter Grill

A hazardous condition may result if a heater is used that has been modified or is not functioning properly. When the heater is working properly:

* The flame is contained within the heater.

* The flame is essentially blue with perhaps some yellow tipping.

* There is no strong disagreeable odor, eye burning or other physical discomfort.

* There is no smoke or soot internal or external to the heater.

* There are no unplanned or unexplained shutdowns of the heater.

The parts list shows the heater as it was constructed. Do not use a heater which is different from that shown.

A heater which is not working right must be repaired, but only by a trained, experienced service person. Contact the factory for the service center closest to you, phone number

(909) 981-5343.

You may also obtain in-warranty or out-of-warranty service by returning the product freight prepaid to:

Qty.

1

1

1

1

1

1

1

1

1

1

1

1

1

1

5

PARTS LIST

Part

Item No.

16 3101

17 3102

18 6500

19 6259

20 6125

21 7253

22 6384

* 4222

24 7291

* 6473

26 3106

27 3105

* 6505

* 7161

* 3451

Description

Louvered Emitter

Pan Hood

Fitting, 1/2" x Close Nipple

Regulator, 4" W.C.

Fitting, Male Connector

Orifice Pilot

Label, Natural Gas Only

Bracket, Piezo

Label, Model/Operating Instructions

Ignitor, Piezo

Leg Base, Side

Leg Base, Front

Fitting, Male Connector

Nut, Piezo

Electrode

Scheu Products Company

8855 Baker Ave.

Rancho Cucamonga, CA 91730

INSTRUCTIONS FOR ORDERING PARTS -

All parts orders must show Heater Model No., Item No., Part

No. and Description. We recommend that only parts supplied by the manufacturer be used on this unit. A locally purchased part may appear to be identical, although in reality it might endanger the heater or the persons operating the heater.

The heater should be serviced only by a trained, experienced service person.

Read the section on "Servicing" before ordering parts.

For parts order, call (909) 981-5343.

SEPTEMBER 1999

P/N 7290L

Qty.

1

1

1

2

1

1

1

1

1

1

1

1

1

1

1

advertisement

Related manuals

advertisement