Pet Immune SAW PIR Motion Sensor with Lithium Battery Installation

Pet Immune SAW PIR Motion Sensor with Lithium Battery Installation
Pet Immune SAW PIR Motion Sensor with
Lithium Battery Installation Instructions
Field-selectable sensitivity options (standard setting
required for pet applications)
Compatible with all Learn Mode control panels
Installation guidelines
Product summary
This PIR was designed for indoor use in the presence of pets
having a combined weight of up to 40 pounds (18 kg). The
following installation guidelines must be met to provide this
false alarm immunity.
A motion sensor (passive-infrared or PIR) detects movement
within a specific area by sensing the infrared energy emitted
from a body as it moves across the sensor’s field of view.
When this motion is detected, the sensor transmits an alarm
signal to the control panel.
Use this motion sensor to protect locations where door/window
sensors are impractical or not needed. For example, use a
motion sensor to protect large areas or open floor plans.
Motion sensors also provide backup protection for door/window
The Pet Immune SAW PIR (60-807-01-95R) utilizes advanced
signal processing, a new custom designed lens, and a new
custom designed sensing element. The combination of these
improvements provides false alarm immunity for pets with a
combined weight of up to 40 pounds (18 kg) while still
providing superior human catch performance.
This wireless motion sensor includes the following
35 feet by 40 feet coverage area
Three minute transmitter lockout time after an alarm that
helps extend battery life
Cover-activated tamper (optional wall-activated tamper is
Supervisory signals transmitted every 64 minutes to the
control panel
Sensor low battery reports (trouble) to the control panel
P/N 466-1837 • REV B • 23FEB11
The sensor must be incline-mounted on a wall surface or
incline mounted in a corner at a mounting height of 7.5
feet (2.3 m) (see Figure 4 on page 2).
The sensitivity switch must be set to Standard.
The pet must not be allowed to climb on objects such as
furniture, boxes, etc. within the field of coverage. See
Figure 2 on page 2 and Figure 3 on page 2 to determine
the sensor’s field of coverage.
Room temperature must be kept between 60º and 120° F
(16º and 49º C).
Do not aim the sensor at windows, fireplaces, air
conditioners, area heaters, forced air heating vents, or
place it in direct sunlight.
Windows should be closed in any area which has an
armed motion sensor.
Position the sensor to protect an area where an intruder
would be most likely to walk across the detection pattern
(see Figure 1 on page 2).
Mount the motion sensor on a rigid surface which is free
from vibrations.
Mount the sensor permanently on a flat wall or in a corner.
Do not set it on a shelf.
Mount the motion sensor on an insulated, outside wall
facing in.
Position the sensor so it faces a solid reference point, like
a wall.
If possible, locate sensors within 100 feet (30.5 m) of the
panel. While a transmitter may have a range of 500 feet
(152 m) or more out in the open, the environment at the
installation site can have a significant effect on transmitter
range. Sometimes a change in sensor location can help
overcome adverse wireless conditions.
Mounting the motion sensor
This sensor must be incline-mounted on a wall surface or
incline mounted in a corner at a mounting height of 7.5 feet.
Figure 4: Wall m ount options
Do not mount the sensor near duct work or other large
metallic surfaces which may affect the RF signals (see
“Final Testing” on page 4). Actual acceptable transmitter
range should be verified for each installation.
Figure 1: Top view of lens coverage area
Figure 5: PIR m ounting plate knockouts
Figure 2: Side view at a m ounting height of 7.5 feet
To mount the sensor:
Figure 3: Overhead detection path
Remove the mounting plate by depressing the button on
the top of the sensor body. With the opposite hand pull the
mounting plate away from the body of the sensor.
Punch out two of the bottom four mounting holes (see
Figure 5 above) to determine which knockouts to use
when mounting the motion sensor. Use the lower-side
holes for corner mounting, or the lower-middle holes for
surface mounting.
If you desire wall-tamper functionality, remove the walltamper knockout (see Figure 5 above).
Note: The wall-tamper switch cannot be used when the
sensor is corner mounted.
Mark the location of the required holes on the mounting
Use wall anchors and screws to secure into place. Attach
the sensor to the mounting plate.
Pet Immune SAW PIR Motion Sensor w ith Lithium Battery Installation Instructions
When testing is completed the PIR can be securely
attached to its mounting plate by screwing the smallest
enclosed screw into the mounting plate hole at the top of
the mounting plate (see Figure 7 below).
Setting the sensitivity on the indoor motion
Environment testing
Turn on all heating or air conditioning sources which would
normally be active during the protection period. Stand away
from the sensor and outside the coverage pattern and watch
for alarms.
For pet applications, the PIR must be set to standard
At least once a year, the range and coverage should be
verified for proper operation. The end user should be instructed
to put the sensor in walk test mode and walk through the far
Figure 6: Sensitivity pins locations
end of the coverage pattern to verify proper detection.
Replacing and Disposing of Batteries
The sensor is powered by 1 AA Lithium battery. When the
system indicates the sensor has a low battery, replace it
When battery replacement is necessary, observe proper
polarity (as shown in the battery compartment) when installing
the new battery, or the sensor may be damaged. Be sure to
Walk Testing
Walk testing should be done to determine the sensor’s actual
coverage area. The edge of the coverage pattern is
determined by the first flash of the LED. This may change
slightly depending upon the sensitivity s etting. Walk test the
unit from both directions to determine the pattern boundaries.
Caution: Replace only with 1 AA lithium battery. Observe
polarity when installing the new battery. Installing the battery
backwards may cause damage to the sensor. Dispose of used
batteries according to the manufacturer’s instructions, and/or
local government authorities. See Figure 7 below for the
battery location.
Remove the sensor body from the mounted mounting
plate, activate the tamper switch, and then remount the
body to activate the 60 second walk test mode.
note that as you look at the battery compartment, on the left
side the positive battery end is down and on the right side the
positive end is up. When the battery is replaced, wait at least 3
minutes before activating the walk test mode.
Figure 7: PIR com ponents
Walk across the coverage pattern to determine the
coverage area, indicated by LED activation. Each
activation extends the walk test mode for an additional 60
After 60 seconds without motion the walk test mode times out
and the LED will no longer activate when motion is detected.
Caution: Excessive use of the walk test mode may reduce
battery life. Use only for initial setup and maintenance testing.
Note: When the walk test mode has ended, an alarm can be
transmitted only after 3 minutes have passed since the
previous alarm. This 3 minute lockout time reduces
unnecessary RF transmissions in high traffic areas thereby
extending battery life.
Refer to the panel installation instructions for information on
programming the sensor into the panel.
Pet Immune SAW PIR Motion Sensor with Lithium Battery Installation Instructions
To trip the sensor:
Remove the PIR from its mounting plate activating the
Simon®, Concord™, Concord Express,
SuperBus® 2000 RF Receiver, Quik Bridge®
1 & 2 Channel and Loop Receivers
Pow er source
1 AA Lithium battery; Part # 60-619 (six
batteries per pack)
Typical battery life
4-6 years at 68° F
Transmitter frequency
319.5 MHz
Final testing should be done to verify radio signal integrity and
confirm control panel programming and response. The actual
transmitter range can be determined by performing a sensor
test as follows:
Operating temperature
32° to 120° F (0° to 49° C) Non-pet
60° to 120° F (16° to 49° C) Pet applications
Storage temperature
-30° to 140° F (-34° to 60° C)
Maximum humidity
90% Relative Humidity non-condensing
2.9 in. (7.4 cm) x 2.4 in. (6.1 cm) x 1.9 in. (4.8
cm) (L x W x H)
tamper switch.
Exit the panel’s programming mode.
Return the PIR to its mounting plate.
Final Testing
After the sensor has been mounted, remove it from its
mounting plate and activate the tamper switch to start the
walk test mode.
Replace the sensor in its mounting plate.
Place the control panel in test mode. Move across the
detection pattern until the sensor’s LED turns on. STOP
your motion.
Listen for the appropriate system response. If the system
does not respond, proceed to “Troubleshooting” below.
Regulatory information
UTC Fire & Security Americas Corporation, Inc.
1275 Red Fox Rd., Arden Hills, MN 55112-6943,
FCC compliance
These devices comply w ith part 15 of the FCC
rules. Operation is subject to the follow ing two
These devices may not cause harmful
Use the following guidelines if the system does not respond
correctly when the sensor is activated.
Check programming and reprogram sensor into panel if
Move the sensor to another location and test for correct
These devices must accept any interference
received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved
by UTC Fire & Security can void the users’
authority to operate the equipment.
Contact information
To relocate a sensor:
Test the sensor a few inches from the original position. or
Increase the distance from the original position and retest
until an acceptable location is found.
Mount the sensor in the new location.
If no location is acceptable, test the sensor as described
For customer support, see
© 2012 UTC Fire & Security Americas Corporation, Inc.
Interlogix is part of UTC Climate Controls & Security, a unit of
United Technologies Corporation.
All rights reserved.
Test a known good sensor at the same location.
If the system does not respond, avoid mounting a sensor
at that location.
If the replacement sensor functions, return the problem
sensor for repair or replacement.
Pet Immune SAW PIR Motion Sensor w ith Lithium Battery Installation Instructions
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF