version:sd 2.0

version:sd 2.0
VERSION:SD 2.0
This manual contains important laser system safety and operation
information. Read and understand all instructions prior to powering on
laser unit the first time, to avoid laser eye injury and to avoid breaking
the law. Keep this manual in a safe place for future reference.
USER MANUAL
WARNING DATA
Lasers can be hazardous and have unique safety considerations.
Permanent eye injury and blindness is possible if lasers are used
incorrectly. Pay close attention to each safety REMARK and
WARNING statement in the user manual. Read all instructions
carefully BEFORE operating this device.
Attention!
Indicates a skill or other useful information for special
situations.
Important!
Indicates important information, to protect people from laser
incident or damage
Caution!
Prevent damage or injury from incorrect operation.
Laser!
Laser safety warming labels.
Recycle
To protect the environment, recycle packing material
wherever possible.
Indoor
The projector is for indoor use only, IP20. Use only in dry
locations. Keep this device away from rain and moisture,
excessive heat, humidity and dust. Do not allow contact with
water or any other fluids, or metallic objects.
Wastebin
Don’t throw this product away just as general trash, please
dispose of this product following the abandon electronic
product regulation in your country.
LLocation
The projector must be installed in a location with adequate
ventilation, at least 50cm (20inches) from adjacent surfaces.
Be sure that no ventilation slots are blocked.
1
USER MANUAL
LASER SAFETY WARNINGS
Potential laser injury hazard exists with this product! Read these
Instructions carefully, which include important information about
installation, safe use and service!
Caution
Avoid direct eye contact with laser 了 light. Never
intentionally expose your eyes or others to direct laser
radiation.
Caution
This laser product can potentially cause instant eye
injury or blindness if laser light directly strikes the eyes.
Caution
It is illegal and dangerous to shine this laser into
audience areas, where the audience or other personnel
could get direct laser beams or bright reflections into
their eyes.
Caution
It is a US Federal offense to shine any laser at aircraft.
Caution
There are no user serviceable parts inside the unit. Do
not open the housing or attempt any repairs yourself. In
the unlikely event your unit may require service, please
contact the dealer nearest to you..
Caution
Use of controls or adjustments or performance of
procedures other than those specified herein may result
in hazardous radiation exposure.
NON-INTERLOCKED HOUSING WARNING
This unit contains high power laser devices internally. Do not open the laser
housing, due to potential exposure to unsafe levels of laser radiation. The
laser power levels accessible if the unit is opened can cause instant
blindness, skin burns and fires.
2
USER MANUAL
LASER SAFETY AND OPERATING INSTRUCTIONS
STOP AND READ ALL LASER SAFETY DATA
Laser light is different from any other light source witch you may be familiar. The
light from this product can potentially cause eyes injury if not set up and used
properly.
Laser light is thousands of times more concentrated than light from any other kind
of light source. This concentration of light power can cause instant eye injuries,
primarily by burning the retina (the light sensitive portion at the back of the eye).
Even if you can not feel “heat” from a laser beam, it can still potentially injure or
blind you or your audience. Even very small amounts of laser light are potentially
hazardous even at long distances. Laser eye injuries can happen quicker than
you can blink.
It is incorrect to think that because these laser entertainment products split the
laser into hundreds of beams or laser beam is scanned out in high speed, that an
individual laser beam is safe for eye exposure. This laser product uses dozens of
milliwatts of laser power (Class 4 levels internally). Many of the individual beams
are potentially hazardous to the eyes.
It is also incorrect to assume that because the laser light is moving, it is safe. This
is not true. Nor, do the laser beams always move. Since eye injuries can occur
instantly, it is critical to prevent the possibility of any direct eye exposure. In the
laser safety regulation, it is not legal to aim Class 4 lasers in areas which people
can get exposed. This is true even if it is aimed below people’s faces, such as on
a dance floor.
z
z
Do not operate laser without first reading and understanding all safety and
technical data in this manual.
Always set up and install all laser effects so that all laser light is at least 3
meters (9.8 feet) above the floor on which people can stand. See “Proper
Laser Set-up & Usage” section later in this manual.
3
USER MANUAL
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
After set up, and prior to public use test laser to ensure proper function. Do not
use if any defect is detected. Do not use if laser emits only one or two laser
beams rather than dozens/hundreds, as this could indicate damage to the
diffraction grating optic, and could allow emission of higher laser levels.
Do not point lasers at people or animals.
Never look into the laser aperture or laser beams.
Do not point lasers in areas in which people can potentially get exposed. such
as uncontrolled balconies, etc.
Do not point lasers at highly reflective surfaces such as windows, mirrors and
shiny metal. Even laser reflections can be hazardous
Never point a laser at aircraft, this is a federal offense.
Never point un-terminated laser beams into the sky.
Do not expose the output optic (aperture) to cleaning chemicals.
Do not use laser if the laser appears to be emitting only one or two beams.
Do not use laser if housing is damaged or open, or if optics appear damaged
in any way.
Never open the laser housing. The high laser power levels inside of the
protective housing can start fires, burn skin and will cause instant eye injury.
Never leave this device running unattended.
The operation of a Class 4 laser show laser is only allowed if the show is
controlled by a skilled and well-trained operator familiar with the data included
in this manual..
The legal requirements for using laser entertainment products vary from
country to country.The user is responsible for the legal requirements at the
location/country of use.
Always use appropriate lighting safety cables when hanging lights and effects
overhead.
LASER EXPOSURE WARNING
LASER LIGHT
AROVID DIRECT EYE EXPOSURE
Further guidelines and safety programs for safe use of lasers can be found in the
ANSI
Z136.1
Standard
“www.laserinstitute.org”.
“For
Safe
Use
of
Lasers”,
available
from
Many local governments, corporations, agencies,
military and others, require all lasers to be used under the guidelines of ANSI
Z136.1. Laser Display guidance can be obtained via the International Laser
Display Association, www.laserist.org.
4
USER MANUAL
LASER SAFETY LABEL REPRODUCTIONS
This is only one laser aperture
on this product. The label
Indicates the laser beam
output aperture
Caution – Class 4 LASER
RADIATION, WHEN OPEN,
AVOID EXPOSURE TO
BEAM
LASER EMISSION DATA
Laser Classification
Class 4
Red Laser Medium
LD GaAlAs 650nm, typical
Green Laser Medium
DPSS Nd:YVO4, 532nm
Blue Laser Medium
LD GeAs 450nm, typical
Beam Diameter
<5mm at aperture
Pulse Data
All pulses < 4Hz (>0.25sec)
Divergence (each beam)
<2 mrad
Divergence (total light)
<40 degrees
Cooling
TEC & Fan Cooling
Scanning
ILDA Standard: 30Kpps
* As measured under IEC measurement conditions for classification.
Note: The laser diode is exposed to extreme conditions due to the
high output power and therefore only has a limited life. Like all
wear parts, the laser diode is not subject to any guarantee claims.
5
USER MANUAL
LASER COMPLIANCE STATEMENT
This laser product complies with EN/IEC 60825-1 Ed 2,2007-03.
GENERAL SAFETY INSTRUCTIONS
Every person involved with installation and maintenance of this device have to
z
z
Be qualified.
Follow the instructions of this manual.
CAUTION!
Be careful with your operations. With a high voltage
you can suffer a dangerous electric shock when
touching the wires!
This device has left out premises in absolutely perfect condition. In order to
maintain this condition and to ensure a safe operation, it is necessary for the user
to follow the safety instructions and warning notes written in this manual.
Important! The manufacturer will not accept liability for any resulting
damages caused by the non-observance of this manual or any
unauthorized modification to the device.
z
z
z
z
z
Please consider that damages caused by manual modifications to the devise
are not subject to warranty.
Never let the power-cord come into contact with other cables! Handle the
power-cord and all connections with the mains with particular caution!
Make sure that the available voltage is not higher than stated on the rear
panel.
Always plug in the power plug least. Make sure that the power-switch is set to
off-position before you connect the device to the mains. The power-plug has
to be accessed after installing the device.
Make sure that the power-cord is never crimped or damaged by sharp edges.
Check the device and the power-cord from time to time.
6
USER MANUAL
z
z
z
z
z
z
z
z
z
z
z
z
z
Always disconnect from the mains, when the devise is not in use or before
cleaning it. Only handle the power-cord by the plug. Never pull out the plug by
tugging the power-cord.
It is essential to connect the yellow/green conductor to earth.
The electric connection, repairs and servicing must be carried out by a
qualified employee.
Do not switch the fixture on and off in short intervals as this would reduce the
laser diode life.
For replacement, please use fuses of same type and rating only.
If the device has been exposed to drastic temperature fluctuation, do not
switch it on immediately. The arising condensation water might damage your
device. Leave the device switched off until it has reached room temperature..
Do not shake the device. Avoid brute force when installing or operating the
device.
When choosing the installation-spot, please make sure that the device is not
exposed to extreme heat, moisture or dust. There should not be any cables
lying around. You endanger your own and the safety of others!
The minimum distance between the fixture and surrounding walls must be
more than 50cm.
Always fix the fixture with an appropriate safety-rope. Fix the safety-rope at
the safety-rope only.
The ambient temperature must be between 10℃ to 40℃.
Please use the original packaging if the device is to be transported.
Please consider that unauthorized modifications on the device are forbidden
due to safety reasons!
CAUTION!
Operate the device only after having familiarized with
its functions. Do not permit operation by persons not
qualified for operating the device. Most damages are the
result of unprofessional operation
CAUTION!
If this device will be operated in any way different to the
one described in this manual, the product may suffer
damages and the warranty word.
7
USER MANUAL
BEFORE OPERATION
Unpacking Instructions
CAUTION!
Immediately upon receiving a fixture, carefully unpack the
carton, check the contents to ensure that all parts are present,
and have been received in good condition. Notify the shipper
immediately and retain packing material for inspection if any
parts appear damage from shipping or the package itself
shows signs of mishandling. Save the package and all packing
materials. In the event that a fixture must be returned to the
factory, it is important that the fixture be returned in the original
factory box and packing.
What is included
The carton or flight case contain following items:
NAME
QTY
Laser Light
1 PCS
KEYs (for key switch)
2PCS
Power Cord
1 PCS
Interlock Connector
1 PCS
1G SD Card
1 PCS
20m DB25 ILDA Cable
1 PCS
USER MANUAL
1 PCS
Flight Case
1PCS
Power Supply
To determine the power requirements for a particular fixture, see the label affixed
to the back plate of the fixture of refer to the fixture’s specifications chart. A
fixture’s listed current rating is its average current draw under normal conditions.
All fixtures must be powered directly off a switched circuit and cannot be run off a
rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer
channel is used solely for a 0% to 100% switch. Before applying power to a fixture,
8
USER MANUAL
channel is used solely for a 0% to 100% switch. Before applying power to a fixture,
check that the source voltage matches the fixture’s requirement.
The unit is supplied with a power plug appropriate to its voltage and
destination. Should any other connections be required they must be
carried out with the following configuration.
Cable(EU)
Cable(US)
Pin
International
Brown
Black
Live
L
Liht blue
White
Neutral
N
Yellow/Green
Green
Earth
DMX-512 connection between fixtures
The fixture is equipped with 2-pin XLR sockets for DMX input and output. The
sockets are wired in parallel. Only use a shielded twisted-pair cable designed for
3-pin XLR-plugs and connectors in order to connect the controller with the fixture
or one fixture with another.
Occupation of the XLR-connection
Caution: At the laser fixture, the DMX-cable has to terminated with a
terminator. Solder a 120 Ohm resistor between Signal (-) and
Signal (+) into a 3-pin XLR-plug and plug and plug it in the
DMX-output of the last fixture.
9
USER MANUAL
Building a serial DMX-chain
z
z
z
z
z
z
z
z
If you are using the standard DMX-controllers, you can connect the
DMX-output of the controller directly with the DMX-input of the first fixture in
the DMX-chain. If you wish to connect DMX-controllers with other
XLR-outputs, you need to use adapter cables.
Connect the DMX-output of the first fixture in the DMX-chain with the
DMX-input of the next fixture. Always connect output with the input of the next
fixture until all fixtures are connected.
If you use a controller with 5 pins DMX connector, you need to use a 5 to 3
pins adpter
At last fixture, the DMX cable has to be terminated with a terminator. Solder a
120 Ohm 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3 pins
XLR-plug and plug it in the DMX-output of the last fixture.
Connect the fixture together in a daisy chain by XLR plug cable from the
output of the fixture to the input of the next fixture. The cable cannot be
branched or split to a Y cable. DMX 512 is a very high speed signal.
Inadequate or damaged cables, soldered joints or corroded connectors can
easily distort the signal and shut down the system.
The DXM output and input connectors are pass-through to maintain the DMX
circuit, when power is disconnected to the unit.
Each fixture needs to have a DMX address to receive the data from the
controller. The DMX address number which could be read from rear panel of
each fixture is between 000~511.
The end of the DMX 512 chain should be terminated to reduce signal errors.
10
USER MANUAL
Proper Laser Set Up & Usage
This fixture has been designed to be hung. It is recommended for safety purposes,
your lighting effect are properly mounted using a suitable hanging clamp and
safety cable.
Items appropriate for safe and effective mounting are easily
sourced from your lighting vendor.
International laser safety regulations require that lasers must be operated in the
fashion illustrated below, with a minimum of 3 meters (9.8 ft) of vertical separation
between the floor and the lowest laser light vertically. Additionally, 2.5 meters of
horizontal separation is required between laser light and audience or other public
spaces.
11
USER MANUAL
Rigging the Fixture
CAUTION!
z
z
z
z
z
z
Please consider the respective national norms during
the installation! The installation must only be carried out
by an authorized employee or dealers!
The installation of the fixture has to be built and constructed in a way that it
can hold 10 times the weight for 1 hour without any harming deformation..
The installation must always be secured with a secondary safety attachment,
e.g. an appropriate catch net. This secondary safety attachment must be
constructed in a way that no part of the installation can fall down if the main
attachment fails.
Make sure the area below the installation place is free from unwanted persons
during rigging, de-rigging and servicing.
The operator has to make sure that safety-relating and machine-technical
installations are approved by an expert before taking into operation for the first
time and after changes before taking into operation another time.
The operator has to make sure that safety-relating and machine-technical
installations are approved by a skilled person once a year.
The fixture should be installed in the position where persons cannot reach and
where persons may walk by or be seated.
CAUTION!
When installing the device, make sure there is no highly
in inflammable material (decoration articles, etc.) in
between a distance of min 0.5 meter.
12
USER MANUAL
PRODUCT OVERVIEW
z
This device has left out premise in absolutely perfect condition. In order to
maintain this condition and to ensure safe operation, it is necessary for the
user to follow the safety instructions and warning notes written in this manual.
z
The manufacturer will not accept liability for any resulting damages caused by
the non-observance of this manual or any unauthorized modification to the
device.
Features
z
STABLE TE COOLED LASER DIODE (CNI)
z
HIGH SPEED 30KHz SCANNER
z
2 x AUTO SHOW + 2 x MUSIC SHOW
z
128 ANIMATED GRAPHIC SHOW PATTERNS
z
HUNDRES PREPROGRAMED BEAM EFFECT
z
MULTIMODE REAL WAVE EFFECT
z
PERFECT WHITE COLOR BALANCE
z
LCD CONTROL MONITOR
z
SMART PRESS BUTTON CONTROL PANEL
z
AUTO SELF CHECKING SYSTEM
z
AUTO, SOUND, DMX & ILDA
z
2 DMX MODES & 13DMX CHANNELS
z
AUTO DETECTED ILDA SIGNAL INTERFACE
z
EXACTLY 3D ADJUSTABL COLOR MIXER
z
KEY SWITCH & INTERLOCK
z
100% LASER SAFETY REGULATION
z
BEAM, WAVE, TEXT, ANIMATION, LOGO
13
USER MANUAL
Front Panel
NO
NAME
FUNCTION
1
POWER
Main power indicated LED. Red is ON.
2
MUSIC
Synchronize to detected music signal
3
Laser output
Laser output aperture.
4
HANDING BAND
Product handing band
HANGING
with 2 knobs on both sides to fasten the unit
and a mounting hole to fix a mounting hook.
5
BRACKET
14
USER MANUAL
Rear Panel
NO
NAME
FUNCTION
6
Switch
Switch on and off the power
7
Mains input
With socket and integrated fuse holder
8
ILDA / Hardware Setting
Music, ILDA, Patterns Setting
9
Urgent and safe switch
Switch off the laser manually if error occurs
10
SD card Storage RAM
SD MMC storage RAM (less than 2G)
11
Key switch
Make sure the professional person use
12
Cooling fan
Cooling and never cover this fan outlet
13
DMX output
3PIN Female XLR port,using for DMX
14
DMX input
3PIN Male XLR port, using for DMX
15
Safety eye
Attach the safety cable
15
USER MANUAL
ILDA / Hardware Setting Panel
NO
NAME
FUNCTION
16
X SIZE
The Size of X axis adjustment
17
Y SIZE
The Size of Y axis adjustment
18
MUSIC
Turn the knob to adjust the audio respond
sensitivity.
19
ILDA THROUGH
Standard ILDA DB25 Output(through)
20
ILDA INPUT
Standard ILDA DB25 Input
21
ILDA
ILDA connection indicator LED. Red is
connection and green is disconnection.
22
RGB
Laser beam output indicator LED.
23
MIC
Microphone. Turn the knob to adjust the
sound activated sensitivity.
24
LCD control Panel
Intelligent LCD control panel of the system
16
USER MANUAL
IMPORTANT
For your own safely and full laser safety
Regulation, we do strongly recommend
You to take this optional switch!
CONTROL & FUNCTION
z
z
z
z
Regular breaks during operation are essential to maximize the life of this
device as it is not designed for continual use.
Do not switch the unit on and off in short time intervals
Always unplug the unit when it is not used for a longer time. Or before
replacing the bulb or start servicing.
In the event of serious operation problems, stop using the fixture and contact
your dealer immediately.
Attention
Laser Safety Scanner Board is included in the system.
The Laser light will be turned off when the scanned angle
is less than 1 degree.
Operating Mode
Attention
Once after every power on laser, the VERSION and
MANUFACTURE INFORMATION will be shown in LCD
monitor of rear panel.
When laser is powered on, LCD monitor on rear panel shows the current
operating standalone mode or DMX address of DMX mode. With help of LCD
control panel, is very easy to set and change the operating mode of laser. After
every resetting and saved, the new mode information will be shown on LCD
monitor at next power on.
17
USER MANUAL
Mode Option, to choose the operating mode of laser.
Confirmation, to confirm the laser to show the present mode at the
next operation.
UP/DOWN, to change operating mode, parameter or DMX address.
OPERATION
18
USER MANUAL
AUTO SHOW 1
z
Press FUNC to enter MODE OPTION
z
Till to AUTO SHOW 1 shown on LCD monitor.
The laser is set at AUTO SHOW 1 standalone mode and it will play the
preprogrammed show until next setting is changed. AUTO SHOW 1 is fast
and hot show which is better for
DISCO.
z
Press ENTER to confirm the laser to
show the present mode at the next
operation.
AUTO SHOW 2
z
Press FUNC to enter MODE OPTION
z
Till to AUTO SHOW 2 shown on LCD monitor.
The laser is set at AUTO SHOW 2 standalone mode and it will play the
preprogrammed show until next setting is changed. AUTO SHOW 2 is slow
and soft show which is better for
MUSIC BAR.
z
Press ENTER to confirm the laser to
show the present mode at the next
operation.
MUSIC SHOW 1
z
Press FUNC to enter MODE OPTION
z
Till to MUSIC SHOW 1 shown on LCD
monitor.
The laser is set at MUSIC SHOW 1
standalone mode and it will play the
preprogrammed show until next setting is changed. MUSIC SHOW 1 is fast
and hot show which is better for DISCO.
z
Press ENTER to confirm the laser to show the present mode at the next
operation.
19
USER MANUAL
MUSIC SHOW 2
z
Press FUNC to enter MODE OPTION
z
Till to MUSIC SHOW 2 shown on LCD
monitor.
The laser is set at MUSIC SHOW 2
standalone mode and it will play the
preprogrammed show until next setting is changed. MUSIC SHOW 2 is slow
and soft show which is better for MUSIC BAR.
z
Press ENTER to confirm the laser to show the present mode at the next
operation.
Attention
In preprogrammed standalone MUSIC SHOW mode, the
laser beam will be blank-out in 3 seconds without
AUDIO/MIC activated signal.
SD SHOW
z
Press FUNC to enter MODE OPTION
z
Press UP/DOWN to choose folder, the folder name have to be 8 characters
including letter or numbers. Any folder name with more than 8 characters can
not be displaced on LED monitor. Press ENTER to choose the folder.
z
Press UP/DOWN to choose show mode: ILDA single show or PRG
preprogrammed show.
z
Press ENTER to confirm the laser to show the present mode at the next
peration.
Attention: Please put ‘ild’ format laser show in SD card only. DO NOT
Save any other files in it. SD maximum support 100 folders with less
than 255 files in each folder. The SD has to be FAT32 format system.
Attention: PRG preprogram show
In SD card in folder ANIMATION, for example, to do the PRG
preprogrammed show, a TXT file (with WINDOW SYSTEM) has to be
done in the same folder. The TXT file has to be renamed to *.PRG
For example:
20
USER MANUAL
In folder ANIMA folder, there are 3 ild file show. They are ANIMA1.ild,
ANIMA2.ild, ANIMA3.ild. If you want to do a preprogram show with
them, you should do the TXT files as:
ANIMA1.ild,12,3
ANIMA2.ild,20,1
ANIMA3.ild,18,4
Save this TXT file with name ANIMA.TXT, change the file name from
ANIMA.TXT to ANIMA.PRG
IMPORTANT NOTES: “ANIMA1.ild” is the ild show name, “12” is
scanner speed, “3” is how many times you want this show to repeat.
DMX MODE
z
Press FUNC to enter MODE OPTION
z
Till to DMX address shown on LCD monitor.
z
Press UP/DOWN to change the DMX
address that you wanted.
z
Press ENTER to confirm the laser
to show the present mode at the
next operation.
Attention
When the laser is connected with DMX controlled or under
control by DMX signal, the DMX indicated LED on front
panel is in RED.
21
USER MANUAL
SLAVE MODE
z
Press FUNC to enter MODE OPTION
z
Till to SLAVE shown on LCD monitor.
Connect MASTER and SLAVE lasers with DMX cable. The SLAVE lasers are
in SLAVE MODE. Check XLR Control cable connection section for your
reference.
z
Press ENTER to confirm the laser to show the present mode at the next
operation.
SETTING MODE
z
Press FUNC to enter MODE OPTION
z
Till to SETTING shown on LCD monitor.
z
Press UP/DOWN to choose MODE. You will have COLOR, MIRROR, MUSIC
modes. Press ENTER to confirm the mode.
z
COLOR MODE:SINGLE COLOR – single white color show,DOUBLE
COLOR – RGY three color show. MULTICOLOR – full color show
z
MIRROR MODE : Press UP/DOWN to change
scanned world mirror. UP is for Y direction mirror
setting and DOWN is for X direction mirror setting.
z
MUSIC MODE:To set the sensitivity of SOUND mode.
ILDA Control Mode
z
z
This unit has the ILDA DB25 port, and it can be controlled by the PC, There is
auto transform set in the inside of the unit to transform the ILDA and
preprogrammed show. when connecting by the 25 pin cable, the unit will be
control by PC, when disconnect the unit, it will be preprogrammed program
control。
In the theory, as long as it is ILDA B25, It can control this unit, but in the
reality, some of the software can not control this unit, for the 4 pin and the 17
pin of the output card has not connect. In fact this is an easy problem. As
long as you connect them. It can control this unit.
22
USER MANUAL
DMX Channels Chart
Several optional operating modes were preprogrammed set into this
laser projector at DMX channel 1. Before control other DMX channels,
please be sure that the channel 1 was set in proper mode (value).
DMX CHANNEL 1 CHART
CHANNEL
VALUE
FUNCTION
000-073
Laser Block Out
074-110
PRG show in SD card
111-147
ILD show in SD card
CH 1
148-165
AUTO SHOW 1
MODE
166-184
AUTO SHOW 2
185-202
MUSIC SHOW 1
203-221
MUSIC SHOW 2
222-255
DMX MODE (Other channels activated)
PRG or ILD mode
CHANNEL
VALUE
DESCRIPTION
CH 2
000-255
Folders
CH 3
000-255
Shows (PRG or ILD)
DMX PATTERN MODE
CHANNEL
CH 2
PATTERN
VALUE
000-255
FUNCTION
84 Patterns as shown in PATTERN LIST
23
USER MANUAL
000-010
NO strobing
011-199
Strobing from slow to fast
200-255
Strobing to Sound
000-125
X position
126-185
Moving from slow to fast
186-225
Moving with random speed
226-245
Random position
246-255
Sound to random position
000-125
Y position
126-185
Moving from slow to fast
186-225
Moving with random speed
226-245
Random position
246-255
Sound to random position
000-010
Original size
011-100
Fixed Sizing
101-150
Zooming out
151-200
Zooming in
201-255
Zooming out and in
CH 7
000-010
No rolling
Y AXIS
ROLLING
011-110
Fixed rolled position
111-255
Rolling from slow to fast
CH 8
000-010
No rolling
X AXIS
ROLLING
011-110
Fixed rolled position
111-255
Rolling from slow to fast
CH 3
Strobe
CH4
X Moving
CH5
Y Moving
CH6
Zooming
000
CH 9
No rolling
000-180
Fixed rolled position
181-217
Rolling to clockwise
218-255
Rolling to anticlockwise
CH 10
000-010
Original pattern
CLIPING
010-074
Fixed cliping
Z AXIS
ROLLING
24
USER MANUAL
CH11
WAVE
CH12
COLOR
CH13
075-104
Clipping out
105-144
Clipping in
145-184
Clipping out and in
185-224
Clipping on
224-255
Clipping off
000-009
Original pattern
010-199
Wave effect in pattern with speed control
200-255
Wave effect in pattern with amplitude control
000-016
White
018-033
Red
034-050
Green
051-067
Blue
068-084
Yellow
085-101
Purple
102-118
Cyan
119-135
White, red, green, blue 4 fixed colors
136-152
Blue, yellow, purple, cyan 4 fixed colors
153-169
Severn colors
170-186
White, red, green, blue 4 colors looping
187-203
Blue, yellow, purple, cyan 4 colors looping
204-220
Severn colors looping
221-237
Random color
238-255
Color changing to sound
000-063
Original pattern
064-127
Pattern with bright points
128-191
Pattern with blanking
192-255
Points to make pattern
25
USER MANUAL
PATTERN LIST
DMX
000-050
051-101
102-152
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
26
153-203
204-254
255
USER MANUAL
SPECIFICTAIONS
Mains Input:
Fuse:
Total Power:
X/Y Axis Beam Angle:
Music Control:
Laser Power:
Laser Classification:
Laser Safety Standard:
Condition Temperature:
DMX Connections:
DMX Channels
Measurement:
N Weight:
AC100~240V, 50/60Hz
250V /1.6A Slow Blow (20mm Glass)
68W
±20°
Audio / Sound Activated
500mW 650nm Red
300mW 532nm Green
400mW 450nm Blue
Class 4
EN60825-1 2007
10~40℃
3 pins XLR Male/Female
Max 13 channels
See picture below
11.5Kg
Every information is subject to change without prior notice.
The availability of particular products may vary by region. Please check with the dealer.
27
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement