SMV 3000 Smart Multivariable Flow Transmitter Specifications, 34

SMV 3000 Smart Multivariable Flow Transmitter Specifications, 34
SMV 3000 Smart Multivariable Flow Transmitter
Specifications
34-SM-03-01 August 2010
Introduction
The SMV 3000 combines integrated sensor and microprocessor
technologies as well as dynamic flow compensation to produce
the most accurate and consistent flow measurement possible,
and is based on ST 3000 technology which is the most reliable in
the industry. These features help improve product yield, increase
process efficiency and enhance plant safety. In addition to the
advantages of superior accuracy and reliability, the SMV 3000
Smart Multivariable Flow Transmitter significantly lowers your
lifetime cost of ownership in several ways.
Models
SMA110
0 to 100 psia
0-1in / 25 inH2O
SMA125
0 to 750 psia
0-1in / 400 inH2O
SMG170
0 to 3,000 psi
0-1in / 400 inH2O
Installation - Wiring cost savings are achieved, as well as
reduced costs of piping, manifolds, mounting, safety barriers,
etc., with the SMV 3000 due to its unique ability to measure both
differential and static pressure with a single sensor, and Process
Temperature with an external RTD or thermocouple.
By dynamically calculating the compensated mass flow, the
SMV 3000 totally eliminates the need for a dedicated flow
computer, or it can free your control system from performing
this function.
Commissioning - The Hand-held SFC III Smart Field
Communicator or SCT 3000 Smart Configuration Toolkit lets a
single technician remotely configure SMV 3000 Smart
Multivariable Flow Transmitters and re-range them when
application requirements change. The SCT must be used to
configure the advanced flow parameters
Figure 1 - SMV 3000 Smart Multivariable Flow Transmitter
Key Features

Unique single capsule sensor design provides highly
accurate measurements of differential pressure, absolute
or gauge pressure and meter body temperature.

3 process measurements (DP, SP and Temp.) and a flow

Flexible Electronics design allows RTD or Thermocouple
calculation from a single transmitter.
Input with standard wiring.

“Smart” features include remote communication,
calibration, configuration and diagnostics.

Flexible software allows flow calculation for liquids, gases
and steam.
Maintenance - The SMV 3000 offers greater accuracy and
stability, reducing the frequency of calibration. Self-diagnostics
can automatically indicate impending problems before they affect
reliability or accuracy. Also, a single technician can diagnose
problems remotely, using the SFC, SCT 3000 or TPS Global
User Station, saving time and reducing cost. The SMV 3000 also
provides improved reliability with a single device replacing up to
three transmitters.

Inventory stocking - Enhanced reliability, combined with the
high turndown capability of the SMV 3000, reduces the quantity
of instruments needed to stock as backups for the installed
transmitters.

Performs dynamic mass and volume flowrate
compensation for Orifice meters and Laminar Flow
Elements for highest accuracy. Standard compensation
supports other primary flow elements:
- Venturi
- Nozzle
- Averaging Pitot Tube
Digital integration with Honeywell control systems
provides local measurement accuracy to the system level
2
Description
Honeywell’s SMV 3000 Smart Multivariable Flow
Transmitter extends our proven “smart” technology to the
measurement of three separate process variables
simultaneously with the ability to calculate compensated mass
or volume flow rate as a fourth process variable according to
industry standard methods for air, gases, steam and liquids.
It measures differential pressure and absolute or gauge
pressure from a single sensor and temperature from a
standard 100-ohm Resistance Temperature Detector (RTD)
or thermocouple type E, J, K, or T input signals.
The SMV 3000’s flow calculation may include compensation
of pressure and/or temperature as well as more complex
variables such as viscosity, discharge coefficient, thermal
expansion factor, velocity of approach factor and gas
expansion factor.
Functions
Proven Pressure Sensor Technology with
characterization
The SMV 3000 utilizes proven Piezoresistive sensor
technology and has an ion-implanted silicon chip hermetically
sealed in its meter body. This single piezoresistive capsule
actually contains three sensors in one; a differential pressure
sensor, an absolute or gauge pressure sensor, and a meter
body temperature sensor. Process pressure applied to the
transmitter’s diaphragm transfers through the fill fluid to the
sensor. Voltage bridge circuits on the chip measures the
differential and static pressures while a resistor in a voltage
divider measures the temperature. These three input signals
from the sensor coupled with the characterization data stored
in the transmitter EPROM are then used by the
microprocessor to calculate highly accurate pressure and
temperature compensated values for the differential pressure
and static pressure measurements.
In this way, the SMV 3000 can provide an output signal that is
stable and fully compensated for changes in process
pressure and ambient temperature over a very wide range.
Microprocessor-based electronics coupled with the sensor
characterization provide higher span-turndown ratio, improved temperature and pressure compensation, and
improved accuracy.
Process Temperature Measurement and
Compensation
Similar to the differential and static pressure measurements,
the SMV 3000’s temperature electronics are characterized for
ambient temperature changes so that the resistance or
millivolt input from a Pt. 100 Ohm RTD or Type J, K, T or E
Thermocouple is compensated for ambient temperature
effects and therefore can be reported as the most accurate
temperature possible. The SMV 3000’s flexibility allows the
connection of either a standard 2, 3 or 4 wire 100 ohm RTD or
a Type J, K, T or E thermocouple without special installation
consideration. RTDs, thermocouples and thermowells can be
ordered from Honeywell under this specification.
SMV 3000 Smart Multivariable Flow Transmitter
Mass Flow Measurements for Steam, Air, Gas
or Liquid
The SMV 3000 includes flow equations for steam, air,
gas and liquids so that one model is all you need in
your plant. The mass flow equation with dynamic
compensation (Equation 1) is based on the ASME
MFC-3M-1989 standard for orifice meters.
Equation 1:
Qm = NCEvY1d
hw  f
2
Where,
Qm = mass flowrate
N = units conversion factor
C = discharge coefficient
Y1 - gas expansion factor
Ev = velocity of approach factor
f = density at flowing conditions
hw = differential pressure
d = bore diameter
SMV 3000 Flow Compensation
Most differential pressure transmitters utilized in steam,
gas and liquid flow applications today measure the
differential pressure across a primary flow element and
report it to a DCS, PLC or flow computer for flow
calculation. Most often, the calculation inside assumes
that the density of the fluid is constant per the following
equation.
hw
Qv = K

Where,
Qv = volumetric flowrate
hw = differential pressure
K = flow factor
 = flowing density
In other applications, one will take the equation a step
further and compensate for changes in pressure and
temperature using additional pressure and temperature
transmitters. For example, if a gas is being measured,
the following volumetric flow equation based on multiple
transmitters - the “Old” approach - applies (Figure 2). Or,
in the case of Mass flowrate,
Qm = K
h
w
P
T
SMV 3000 Smart Multivariable Flow Transmitter
3
The “Old” Flow Approach
Today, the three key measurements
(differential pressure, static pressure and
process temperature) and the flow calculation
can be made with one multivariable
transmitter. So, whether you just want to
compensate for density or use full dynamic
flow compensation, consider the SMV 3000
and the “Enhanced” flow approach (Figure 3).
Unlike most DP transmitters, the SMV 3000
with dynamic compensation can correct flow
errors due to the K factor. Per Equation 1, the
K factor is not a constant and can vary:
Flow Computer or DCS
Q v = k hw x T
FIC
P
PT
PT
2
k = NCEvY1d
DP
Pressure
Temp.
Figure 2 —Flow Compensation Using the “Old” Approach
Description of Flow Variables for Dynamic
Flow Compensation
Dynamic flow compensation is the process of
measuring the required variables (differential pressure,
static pressure and temperature) and using these
variables to perform real time, calculations of variables
such as density, viscosity, Reynolds number,
discharge coefficient, thermal expansion factor and
gas expansion factor - all which can affect the
accuracy of your mass flow measurement.
With the SMV 3000, you have the flexibility to choose
which variables you need to compensate. For
example, the transmitter can be easily configured to
compensate for density only and calculate flowrate via
a standard equation. If you have a liquid, steam or gas
application with small flow turndown requirements,
choose the easy, standard equation and in minutes
your mass or volumetric flowrate is compensated for
density changes.
On the other hand, if you have a more demanding flow
application utilizing an orifice plate or laminar flow
element that requires high accuracy at larger flow
turndowns, choose the more complex mass or volumetric
flow equation and compensate for density as well as
other variables such as viscosity, discharge coefficient,
gas expansion factor, velocity of approach factor and
thermal expansion factor.
The “Enhanced” Flow Approach
D yn am ic com p ensation o f
F lo w inside S MV 3000
Q m  NCE v Y 1 d 2 h w 
S MV 3000
Transm itter
C on trol d on e in DC S, PL C
or Sin gle L oo p C o ntro ller
F IC
PT
T em p .
Figure 3 —Flow Compensation Using the
“Enhanced” Approach
4
SMV 3000 Smart Multivariable Flow Transmitter
Discharge Coefficient
Discharge coefficient is defined as the true flowrate divided
by the theoretical flowrate and corrects the theoretical
equation for the influence of velocity profile (Reynolds
number), the assumption of no energy loss between taps,
and pressure tap location. It is dependent on the primary
flow element, the  ratio and the Reynolds number.
Reynolds number is in turn dependent on the viscosity,
density and velocity of the fluid as well as the pipe
diameter per the following equation:
Re =
vD

where,
 = velocity
D = inside pipe diameter
 = fluid density
 = fluid viscosity
The SMV 3000 can be configured to dynamically
compensate for discharge coefficient.
This method follows the standard Stoltz equation for orifice,
Venturi and nozzle primary elements to predict discharge
coefficient for flowrate in the turbulent regime Re > 4000.
C = C +
b
Re n
Where,
C = Discharge coefficient at
infinite Re #
b = function of primary element
Re = Reynolds number
n = depends on the primary
element
As an example, a fluid at 600 degrees F could cause as
much as 1% error in flow measurement using 300 series
stainless steel materials.
Gas Expansion Factor
The gas expansion factor corrects for density differences
between pressure taps due to expansion of compressible
fluids. It does not apply for liquids which are essentially
non-compressible and approaches unity when there are
small differential pressures for gas and steam
measurements. The gas expansion factor is dependent on
the Beta ratio, the Isentropic exponent, the differential
pressure and the static pressure of the fluid per the following
equation:
where,
1 = 1 - (0.41 + 0.354)X1/k
 = beta ratio
X1 = hw /P
k = isentropic exp. (ratio of specific heats)
The SMV 3000 dynamically compensates for gas
expansion effects and provides better mass flow accuracy,
especially for low static pressure applications.
Velocity of Approach Factor
Ev is dependent on the Beta ratio as defined by the following
equation:
Ev = 1/
1- 4
Dynamically compensating for discharge coefficient allows
the SMV 3000 to obtain better flow accuracy at higher
turndowns for orifice, Venturi and nozzles.
In turn, Beta ratio is dependent on the bore diameter and
pipe diameter which are functions of temperature. The SMV
3000 compensates dynamically for velocity of approach
factor by calculating the true Beta ratio at flowing
temperature. This ensures high flowrate accuracy at low
and high temperature applications.
Thermal Expansion Factor
Density and Viscosity of Fluids
The material of the process pipe and primary flow element
expands or contracts with changes in temperature of the
fluid being measured. When a primary flow element, such
as an orifice, is sized, the flowrate is calculated based on the
Beta ratio (d/D) at 68 degrees F. The SMV 3000, using the
thermal expansion coefficients which are dependent of the
material of the pipe and flow element, calculates the change
in Beta ratio per the following equations:
 = d/D
D = 1 + p(Tf - 68)Dref
d = 1 + pe(Tf - 68)dref
where,
 = beta ratio
D = pipe diameter
d = bore diameter
Dref = pipe diameter at design
dref = bore diameter at design
p = Thermal Expansion Coef.
pe = Thermal Expansion Coef.
Tf = flowing temperature
Density directly effects the flowrate calculation as well as
the discharge coefficient due to changes in the Reynolds
number. The SMV 3000 can be configured to compensate
for density of fluids due to changes in the temperature
and/or pressure per the following:

Gases as a function of P and T per the Gas Law
Equations.

Steam as function of P and T based on the ASME
Tables.

Liquids as a function of T per a 5th Order Polynomial.
 = d1 + d2TF + d3TF2 + d4TF3 + d5TF4
temperature
temperature
of pipe
of bore
Changes in the viscosity of a fluid due to changes in
temperature can also effect the Reynolds number and
therefore discharge coefficient. The SMV 3000 can
compensate the viscosity of liquids based on the following
5th order polynomial equation:
 = v1 + v2TF + v3TF2 + v4TF3 + v5TF
SMV 3000 Smart Multivariable Flow Transmitter
5
Support of Proprietary Flow Elements
The SMV 3000 with dynamic flow compensation supports
orifice meters and the Meriam Laminar Flow Elements.
The SMV 3000 with density compensation supports other
flow elements such as Venturi meters, nozzles, averaging
pitot tubes.
Averaging Pitot Tubes
Averaging pitot tubes are a low differential pressure,
insertion type flow element and can be used in clean
steam, air, gas and liquid applications. Since averaging
pitot tubes are insertion type elements, they have lower
installation costs than many other primary flow elements.
The SMV 3000 can be configured to compensate for
density and calculate flowrate for liquids, gases and steam
utilizing averaging pitot tubes (Figure 4).
And for mass flowrate:
Qm = Qv • 
Where,
Qm = standard volumetric flowrate
 = density at standard conditions
The relationship between flowrate and differential pressure
can be determined two ways.
The first method uses a 6th order polynomial equation that
custom fits the flow element. The second method is an nsegment fit (maximum n = 5) between flow and differential
pressure which also custom fits the flow element.
Figure 4 —SMV 3000 with Averaging Pitot Tube
Meriam Laminar Flow Element
Laminar Flow Elements (Figure 5) are gas volume rate of
flow differential producers operating on capillary flow
principles and are similar to averaging pitot tubes in that
they are low differential pressure producers. They are
applicable over wider flow ranges than conventional types of
primary flow elements and are ideally suited for
measurements of combustion air and gases such as argon,
helium and nitrogen. Laminar Flow Elements behave
according to the following flow formulas and can be
configured for standard volumetric flowrate:
2
(Ts/Tf) • (Pf/Ps) • (w/d)
Qv = (B x hw + C x hw ) • (s/w) •
Where,
Qv = standard volumetric flowrate
B & C = calibration constants
hw = differential pressure
s = standard viscosity
Tf = flowing temperature
Pf = flowing pressure
w = wet air density
d = dry air density
Figure 5 —SMV 3000 with Meriam Laminar Flow
Elements
The SMV 3000 can use either one of these methods as well
as compensate for density and viscosity to increase the
accuracy of the flow measurement for the Laminar Flow
Element over greater flow turndowns.
6
SMV 3000 Smart Multivariable Flow Transmitter
Smart Technology Delivers Broad Benefits and Reduces Total Cost of Ownership
Other Multivariable Applications
Smart Configuration Flexibility
Most multivariable transmitters are used in flow
applications. However, there are other applications
which require that multiple process variables (DP, AP
and T) be transmitted to a control system - DCS or PLC.
It is in the control system where a calculation such as
compensated level for liquid level applications or
complex calculations to infer composition in distillation
columns are performed. A SMV 3000 in these
applications can save substantial wiring, installation and
purchase costs versus 2 or 3 separate single-variable
transmitters. Whether integrating digitally to a
Experion/TDC/TPS 3000 Control System or providing 4
analog 1-5 V outputs to a PLC or DCS via the MVA
Multivariable Analog Card, the SMV 3000 is very cost
effective in multivariable applications.
Like other Smartline Transmitters, the SMV 3000 features
two-way communication between the operator and the
transmitter via the SCT 3000 Smart Configuration Toolkit or
SFC - Smart Field Communicator or MC Toolkit. You connect
the SFC or SCT anywhere that you can access the
transmitter signal lines. These communicators provide the
capabilities of transmitter adjustments and diagnostics from
remote locations, such as the field installation, I/O rack or
control room. The SFC and SCT3000 support other
Smartline Instruments too: ST 3000, STT 3000.
Figure 7 — MC Tookit
Figure 6 — Smart Field Communicator
The SCT 3000 has an advantage over the SFC in that it
can also be used to configure the complete SMV 3000
database and save this database for later access. The
SCT 3000 is a software package and hardware interface
which runs on an IBM compatible computer utilizing the
Windows 95, Windows 98 or Windows NT platforms. The
SCT 3000 must be used to configure the advanced flow
parameters for the SMV 3000.
Figure 8 — SCT 3000
SMV 3000 Smart Multivariable Flow Transmitter
Digital Integration Links the SMV 3000 to
Experion and TDC/TPS 3000 for greater
7
MVA Provides Integration with Analog Systems
process efficiency
Digital Integration combines the functions of TDC/TPS
3000 system with the strengths of the SMV 3000 to help
achieve maximum productivity, by providing:





Database security and integrity - PV Status
transmission precedes the PV value,
guaranteeing that a bad PV is not used in a
control algorithm.
Bidirectional communication and a
common database for the system and the
transmitter - Data upload and download
capability lowers transmitter installation costs.
Single-window diagnostics for the
transmitter (electronics and meter body)
and loop - Remote troubleshooting reduces
maintenance effort and expedites repairs.
Automatic historization of all transmitter
parameter changes - System maintenance
log automatically provides audit trail of
changes.
Enhanced accuracy - Elimination of D/A and
A/D converters improves measurement
accuracy.
The MultiVariable Analog (MVA) interface in Figure 6
provides a cost effective way to interface with analog
instrumentation while utilizing all the advantages of
Honeywell’s digitally enhanced (DE) communications.
The MVA is fully compatible with all Honeywell Smartline™
transmitters. This includes the SMV 3000 Smart
Multivariable Transmitter, ST 3000 Smart Pressure
Transmitters, STT 3000 Smart Temperature Transmitter.
The MVA also works in conjunction with any of Honeywell’s
DE control system interfaces (STDC, STI-MV). In addition,
Honeywell’s handheld communicators, SFC III and SCT
3000 and the MC Tool kit, may be used with no
disturbances to the analog outputs or device status. MVA
accepts the digital DE signal from any Smartline™
transmitter and outputs analog signals. Digitally integrated
to the SMV 3000, the MVA can provide up to 4 analog 1-5
Volt outputs for differential pressure, static pressure,
temperature and compensated flowrate. This provides an
economical means of integrating SMV 3000 in analog
applications when all process variables are required.
Digital Integration of the SMV 3000 Smart Multivariable
Flow Transmitter with Experion/TDC/TPS 3000 allows
you to combine advanced transmitter technology with
our state-of-the-art, process connected controllers - the
Process Manager, Advanced Process Manager and
High Performance Process Manager.
Digital Integration of the SMV 3000 Smart Multivariable
Flow Transmitter with Experion/TDC/TPS 3000
improves the integrity of the process data
measurements, letting you monitor process variability
with greater accuracy. Accurate and more reliable data
lets you implement advanced control strategies,
providing greater bottom-line profits.
Figure 6 —MultiVariable Analog Interface
MVA141 Ordered Separately under Spec. 34-MV-03-01
8
SMV 3000 Smart Multivariable Flow Transmitter
SMV 3000 Specifications
Operating Conditions
Parameter
Reference
Condition
Rated
Condition
Operative
Limits
Transportation
and Storage
–40 to 93
–40 to 200
–55 to 125
–67 to 257
Ambient Temperature
C
F
25 ±1
77 ±2
–40 to 85
–40 to 185
Meter Body Temperature
C
F
25 ±1
77 ±2
–40 to 110
1
–40 to 230
–40 to 125
1
–40 to 257
–55 to 125
–67 to 257
10 to 55
0 to 100
0 to 100
0 to 100
Atmospheric
Atmospheric
25
13
2 (short term )
2
1 (short term )
Humidity
%RH
Vacuum Region - Minimum Pressure
mmHg absolute
inH2O absolute
Supply Voltage, Current, and Load
Resistance
3
4
2
3
(ST 3000 products are rated to Maximum
Allowable Working Pressure. MAWP depends
on Approval Agency and transmitter materials of
construction.)
2
1
Voltage Range: 10.8 to 42.4 Vdc at terminals
Current Range: 3.0 to 20.8 mA
Load Resistance: 0 to 1440 ohms (as shown in Figure 7).
Maximum Allowable Working
4
Pressure (MAWP)
1
1
SMA110 = 100 psi, 7 bar
3
SMA125 = 3,000 psi, 210 bar
3
SMG170 = 3,000 psi, 210 bar
Static Pressure Limit = Maximum Allowable Working Pressure (MAWP) =
Overpressure Limit
For CTFE fill fluid, the rating is –15 to 110C (5 to 230F).
Short term equals 2 hours at 70C (158F).
The MAWP is intended as a pressure safety limit. Honeywell does not recommend use above the PV 2 Upper Range Limit.
Consult factory for MAWP of transmitters that require CSA approval (CRN)
1440
1200
Loop
Resistance
(ohms)
= Operating
Area
NOTE: A minimum of 250
0hms of loop resistance is
necessary to support
communications. Loop
resistance equals barrier
resistance plus wire
resistance plus receiver
resistance. Also 45 volt
operation is permitted if
not an intrinsically safe
installation.
800
650
450
250
0
10.8 16.28 20.63 25 28.3
37.0
Operating Voltage (Vdc)
42.4
21012
Figure 7 —Supply Voltage and Loop Resistance Chart.
SMV 3000 Smart Multivariable Flow Transmitter
9
SMV 3000 Specifications, continued
Performance Under Rated Conditions5 - Differential Pressure Measurement - SMA110
Parameter
Description
Upper Range Limit
± 25 inH2O (62.5 mbar) at 39.2F (4C) standard reference temperature for inches of
water measurement range.
Turndown Ratio
25 to 1
Minimum Span
±1.0 inH2O (2.5 mbar)
Zero Elevation and Suppression
No limit (except minimum span) with ±100% URL.
Accuracy (Reference – Includes
combined effects of linearity,
hysteresis, and repeatability)
• Applies for model with Stainless
Steel barrier diaphragms
• Accuracy includes residual error
after averaging successive
readings.
In Analog Mode: ±0.125% of calibrated span or upper range value (URV), whichever
is greater, - Terminal based.
For URV below reference point (10 inH2O), accuracy equals:

 10 inH 2 O 
 span inH O  or

2 
 0.025  0.1 

 25 mbar 
 in % of span.
 span mbar 

In Digital Mode: ±0.1% of calibrated span or upper range value (URV), whichever is
greater, - Terminal based.
For URV below reference point (10 inH2O), accuracy equals:
10 inH2O
± 0. 1  span inH O or ± 0. 1

2 
Zero Temperature Effect per 28C
(50F)
• Applies for model with Stainless
Steel barrier diaphragms

 0.025  0.1
25 mbar
( span
mbar) in % of span.
In Analog Mode: ±0.525% of calibrated span.
For URV below reference point (10 inH2O), effect equals:

 10 inH 2 O 
 span inH O  or

2 
 0.025  0.50 


 25 mbar 
 in % of span.
 span mbar 
 0.025  0.50 

In Digital Mode: ±0.5% of calibrated span.
For URV below reference point (10 inH2O), effect equals:
10 inH2O
±0.50  span inH O or ±0.50

2 
Combined Zero and Span
Temperature Effect per 28C (50F)
• Applies for model with Stainless
Steel barrier diaphragms
25 mbar
( span
mbar) in % of span.
In Analog Mode: ±0.675% of calibrated span.
For URV below reference point (10 inH2O), effect equals:

 10 inH 2 O 
 span inH O 

2 
 0.175  0.50


 25 mbar 

 span mbar 
or  0.175  0.50

in % of span
In Digital Mode: ±0. 625% of calibrated span.
For URV below reference point (10 inH2O), effect equals:

 10 inH 2 O 
 span inH O 

2 
 0.125  0.50



Stability (At Reference Conditions)
±1.0% of URL per year.
Damping Time Constant
Adjustable for 0 to 32 seconds digital damping.
5
 25 mbar 

 span mbar 
or  0.125  0.50
in % of span
Performance specifications are based on reference conditions of 25C (77F), zero (0) static pressure, 10 to 55% RH, and 316 Stainless Steel barrier diaphragm.
10
SMV 3000 Smart Multivariable Flow Transmitter
SMV 3000 Specifications, continued
Performance Under Rated Conditions5 - Differential Pressure Measurement - SMA125
Parameter
Upper Range Limit
Turndown Ratio
Minimum Span
Description
±400 inH2O (1000 mbar) at 39.2F (4C) standard reference temperature for inches of
water measurement range.
400 : 1
±1 inH2O (2.5 mbar)
Zero Elevation and Suppression No limit (except minimum span) with ±100% URL.
In Analog Mode: ±0.10% of calibrated span or upper range value (URV), whichever is
Accuracy (Reference – Includes
greater, - Terminal based.
combined effects of linearity,
For URV below reference point (25 inH2O), accuracy equals:
hysteresis, and repeatability)
• Applies for model with

 25 inH 2 O 

 62 mbar 
Stainless Steel barrier
 0.025  0.075 
 span inH O  or  0.025  0.075  span mbar  in % of span.
diaphragms




2 

• Accuracy includes residual error
In Digital Mode: ±0.075% of calibrated span or upper range value (URV), whichever is
after averaging successive
greater, - Terminal based.
readings.
For URV below reference point (25 inH2O), accuracy equals:
 25 inH 2 O 
 span inH O  or

2 

 0.0125  0.0625 

Zero Temperature Effect per
28C (50F)
• Applies for model with
Stainless Steel barrier
diaphragms

 62 mbar 
 in % of span.
 span mbar 
 0.0125  0.0625 

In Analog Mode: ±0.1125% of calibrated span.
For URV below reference point (50 inH2O), effect equals:

 50 inH 2O 
 span inH O 

2 
 0.0125  0.10




 span
or  0.0125  0.10


mbar 
125 mbar
in % of span
In Digital Mode: ±0.10% of calibrated span.
For URV below reference point (50 inH2O), effect equals:
50 inH2O
±0.10  span inH O or ±0.10

2 
Combined Zero and Span
Temperature Effect per 28C
(50F)
• Applies for model with
Stainless Steel barrier
diaphragms
125 mbar
( span
mbar) in % of span.
In Analog Mode: ±0.2625% of calibrated span.
For URV below reference point (50 inH2O), effect equals:

 50 inH 2O 
 span inH O 

2 
 0.1625  0.10 




 span
or  0.1625  0.10 
in % of span
In Digital Mode: ±0.225% of calibrated span.
For URV below reference point (50 inH2O), effect equals:

 50 inH 2 O 
 span inH O 

2 
 0.125  0.10 


 125 mbar 

 span mbar 
or  0.125  0.10 

Zero Static Pressure Effect per
1,000 psi (70 bar)
• Applies for model with
Stainless Steel barrier
diaphragms
±0.24% of calibrated span.
For URV below reference point (50 inH2O), effect equals:
Combined Zero and Span Static
Pressure Effect per 1,000 psi
(70 bar)
• Applies for model with
Stainless Steel barrier
diaphragms
±1.04% of calibrated span.
For URV below reference point (50 inH2O), effect equals:
Stability (At Reference Conditions)
±0.0625% of URL per year.
Damping Time Constant
Adjustable for 0 to 32 seconds digital damping.
5


mbar 
125 mbar

 50 inH 2 O 
 span inH O 

2 
 0.05  0.19 


 0.85  0.19

 50 inH 2 O 


 span inH 2 O 

or  0.05  0.19


or  0.85  0.19

 125 mbar 


 span mbar 
 125 mbar 


 span mbar 
in % of span
in % of span
in % of span
Performance specifications are based on reference conditions of 25C (77F), zero (0) static pressure, 10 to 55% RH, and 316 Stainless Steel barrier diaphragm.
SMV 3000 Smart Multivariable Flow Transmitter
11
SMV 3000 Specifications, continued
Performance Under Rated Conditions5 - Differential Pressure Measurement - SMG170
Parameter
Upper Range Limit
Turndown Ratio
Minimum Span
Description
400 inH2O (1000 mbar) at 39.2F (4C) standard reference temperature for inches of
water measurement range.
400 to 1
1 inH2O (2.5 mbar)
Zero Elevation and Suppression No limit (except minimum span) with ±100% URL. Specifications valid from –5 to +100%
URL.
Accuracy (Reference – Includes
In Analog Mode: ±0.10% of calibrated span or upper range value (URV), whichever is
greater, - Terminal based.
combined effects of linearity,
hysteresis, and repeatability)
For URV below reference point (50 inH2O), accuracy equals:
• Applies for model with

 50 inH 2 O 

Stainless Steel barrier
 125 mbar 
 0.025  0.075 
diaphragms
 span inH O  or  0.025  0.075  span mbar  in % of span.




2 

• Accuracy includes residual error
after averaging successive
In Digital Mode: ±0.075% of calibrated span or upper range value (URV), whichever is
readings.
greater, - Terminal based.
For URV below reference point (50 inH2O), accuracy equals:



 span
 0.0125  0.0625 

Zero Temperature Effect per
28C (50F)
• Applies for model with
Stainless Steel barrier
diaphragms


 125 mbar 
 or  0.0125  0.0625 
 in % of span.
inH 2 O  
 span mbar 

50 inH 2 O
In Analog Mode: ±0.1375% of calibrated span.
For URV below reference point (100 inH2O), effect equals:
 100 inH 2 O 

 250 mbar 
 span inH O  or  0.0125  0.125  span mbar  in % of span.




2 

 0.0125  0.125 

In Digital Mode: ±0.125% of calibrated span.
For URV below reference point (100 inH2O), effect equals:
100 inH2O
250 mbar
±0.125  span inH O or ±0.125 span mbar in % of span.

2 
(
Combined Zero and Span
Temperature Effect per 28C
(50F)
• Applies for model with
Stainless Steel barrier
diaphragms
)
In Analog Mode: ±0.35% of calibrated span.
For URV below reference point (100 inH2O), effect equals:

 100 inH 2 O 
 span inH O  or

2 
 0.225  0.125 




 span
 0.225  0.125 
In Digital Mode: ±0.325% of calibrated span.
For URV below reference point (100 inH2O), effect equals:

 100 inH 2 O 
 span inH O  or

2 
 0.20  0.125 


 250 mbar 
 in % of span.
 span mbar 
 0.20  0.125 

Zero Static Pressure Effect per
1,000 psi (68 bar)
• Applies for model with
Stainless Steel barrier
diaphragms
±0.15% of calibrated span.
For URV below reference point (100 inH2O), effect equals:
Combined Zero and Span Static
Pressure Effect per 1,000 psi
(68 bar)
• Applies for model with
Stainless Steel barrier
diaphragms
Stability (At Reference Conditions)
Damping Time Constant
±0.35% of calibrated span.
For URV below reference point (100 inH2O), effect equals:
5

 in % of span.
mbar 
250 mbar

 100 inH 2 O 

 250 mbar 
 span inH O  or  0.025  0.125  span mbar  in % of span.




2 
 0.025  0.125 


 100 inH 2 O 
 span inH O  or

2 
 0.225  0.125 




 span
 0.225  0.125 

 in % of span.
mbar  
250 mbar
±0.0625% of URL per year.
Adjustable for 0 to 32 seconds digital damping.
Performance specifications are based on reference conditions of 25C (77F), zero (0) static pressure, 10 to 55% RH, and 316 Stainless Steel barrier diaphragm.
12
SMV 3000 Smart Multivariable Flow Transmitter
SMV 3000 Specifications, continued
Performance Under Rated Conditions5 - Absolute Pressure Measurement - SMA110
Parameter
Description
Upper Range Limit (URL)
100 psia (7 bara)
Turndown Ratio
20 to 1
Minimum Span
5 psia (.35 bara)
Zero Suppression
No limit (except minimum span) from absolute zero to 100% URL. Specifications valid
over this range.
Accuracy (Reference – Includes
combined effects of linearity,
hysteresis, and repeatability)
• Applies for model with Stainless
Steel barrier diaphragms
• Accuracy includes residual error
after averaging successive
readings.
In Analog Mode: ±0.10% of calibrated span or upper range value (URV), whichever is
greater - Terminal based.
For URV below reference point (20 psi), accuracy equals:
 20 psi 
 or
 span psi 


 0.025  0.075 

In Digital Mode: ±0.075% of calibrated span or upper range value (URV), whichever is
greater, - Terminal based.
For URV below reference point (20 psi), accuracy equals:

 20 psi 
 or
 span psi 
 0.0125  0.0625 

Zero Temperature Effect per 28C
(50F)
• Applies for model with Stainless
Steel barrier diaphragms
 1.4 bar 
 in % of span.
 span bar 

 0.025  0.075 

 1.4 bar 
 in % of span.
 span bar 
 0.0125  0.0625 

In Analog Mode: ±0.125% of calibrated span.
For URV below reference point (50 psi), effect equals:

 0.025  0.10

 50 psi 
 or

 span psi 

 0.025  0.10

 3.5 bar 
 in % of span.

 span bar 
In Digital Mode: ±0.10% of calibrated span.
For URV below reference point (50 psi), effect equals:
±0.10
Combined Zero and Span
Temperature Effect per 28C
(50F)
• Applies for model with Stainless
Steel barrier diaphragms
50 psi
3.5 bar
( span
psi) or ±0.10 ( span bar) in % of span.
In Analog Mode: ±0.2625% of calibrated span.
For URV below reference point (50 psi), effect equals:

 0.1625  0.10

 50 psi 

 or
 span psi 

 0.1625  0.10

 3.5 bar 

 in % of span.
 span bar 
In Digital Mode: ±0.225% of calibrated span.
For URV below reference point (50 psi), effect equals:

 0.125  0.10

 50 psi 

 or
 span psi 

 0.125  0.10

Stability (At Reference Conditions)
±0.125% of URL per year.
Damping Time Constant
Adjustable from 0 to 32 seconds digital damping.
5
 3.5 bar 

 in % of span.
 span bar 
Performance specifications are based on reference conditions of 25C (77F), zero (0) static pressure, 10 to 55% RH, and 316 Stainless Steel barrier diaphragm.
SMV 3000 Smart Multivariable Flow Transmitter
13
SMV 3000 Specifications, continued
Performance Under Rated Conditions5 - Absolute Pressure Measurement - SMA125
Parameter
Description
Upper Range Limit (URL)
750 psia (52 bara)
Turndown Ratio
150 to 1
Minimum Span
5 psia (0.3 bara)
Zero Suppression
No limit (except minimum span) from absolute zero to 100% URL. Specifications
valid over this range.
Accuracy (Reference – Includes
combined effects of linearity,
hysteresis, and repeatability)
• Applies for model with Stainless
Steel barrier diaphragms
• Accuracy includes residual error
after averaging successive
readings.
In Analog Mode: ±0.10% of calibrated span or upper range value (URV), whichever
is greater - Terminal based.
For URV below reference point (20 psi), accuracy equals:

 20 psi 
 or
 span psi 

 0.025  0.075 


In Digital Mode: ±0.075% of calibrated span or upper range value (URV), whichever
is greater, - Terminal based.
For URV below reference point (20 psi), accuracy equals:

 20 psi 
 or
 span psi 
 0.0125  0.0625 

Zero Temperature Effect per 28C
(50F)
• Applies for model with Stainless
Steel barrier diaphragms
 1.4 bar 
 in % of span.
 span bar 
 0.025  0.075 

 1.4 bar 
 in % of span.
 span bar 
 0.0125  0.0625 

In Analog Mode: ±0.1125% of calibrated span.
For URV below reference point (50 psi), effect equals:

 0.0125  0.10

 50 psi 

 or
 span psi 

 0.0125  0.10

 3.5 bar 

 in % of span.
 span bar 
In Digital Mode: ±0.10% of calibrated span.
For URV below reference point (50 psi), effect equals:
±0.10
Combined Zero and Span
Temperature Effect per 28C
(50F)
• Applies for model with Stainless
Steel barrier diaphragms
50 psi
3.5 bar
( span
psi) or ±0.10 ( span bar) in % of span.
In Analog Mode: ±0.2625% of calibrated span.
For URV below reference point (50 psi), effect equals:

 0.1625  0.10

 50 psi 
 or

 span psi 

 0.1625  0.10

 3.5 bar 
 in % of span.

 span bar 
In Digital Mode: ±0.225% of calibrated span.

 0.125  0.10

 50 psi 
 or

 span psi 

 0.125  0.10

Stability (At Reference Conditions)
±0.016% of URL per year.
Damping Time Constant
Adjustable from 0 to 32 seconds digital damping.
5
 3.5 bar 
 in % of span.

 span bar 
Performance specifications are based on reference conditions of 25C (77F), zero (0) static pressure, 10 to 55% RH, and 316 Stainless Steel barrier diaphragm.
14
SMV 3000 Smart Multivariable Flow Transmitter
SMV 3000 Specifications, continued
Performance Under Rated Conditions5 - Gauge Pressure Measurement - SMG170
Parameter
Description
Upper Range Limit (URL)
3,000 psig (210 barg)
Turndown Ratio
50 to 1
Minimum Span
60 psig (1.04 barg)
Zero Suppression
No limit (except minimum span) from absolute zero to 100% URL. Specifications
valid over this range.
Accuracy (Reference – Includes
combined effects of linearity,
hysteresis, and repeatability)
• Applies for model with Stainless
Steel barrier diaphragms
• Accuracy includes residual error
after averaging successive
readings.
In Analog Mode: ±0.10% of calibrated span or upper range value (URV), whichever
is greater - Terminal based.
For URV below reference point (300 psi), accuracy equals:

 300 psi 
 or
 span psi 
 0.025  0.075 



In Digital Mode: ±0.075% of calibrated span or upper range value (URV), whichever
is greater, - Terminal based.
For URV below reference point (300 psi), accuracy equals:

 300 psi 
 or
 span psi 
 0.0125  0.0625 

Zero Temperature Effect per 28C
(50F)
• Applies for model with Stainless
Steel barrier diaphragms
 21 bar 
 in % of span.
 span bar 
 0.025  0.075 

 21 bar 
 in % of span.
 span bar 
 0.0125  0.0625 

In Analog Mode: ±0.1125% of calibrated span.
For URV below reference point (300 psi), effect equals:

 300 psi 
 or
 span psi 
 0.0125  0.10 


 21 bar 
 in % of span.
 span bar 
 0.0125  0.10 

In Digital Mode: ±0.10% of calibrated span.
For URV below reference point (300 psi), effect equals:
±0.10
Combined Zero and Span
Temperature Effect per 28C
(50F)
• Applies for model with Stainless
Steel barrier diaphragms
300 psi
21 bar
( span
psi) or ±0.10 ( span bar) in % of span.
In Analog Mode: ±0.25% of calibrated span.
For URV below reference point (300 psi), effect equals:

 300 psi 
 or
 span psi 
 0.15  0.10 


 21 bar 
 in % of span.
 span bar 
 0.15  0.10 

In Digital Mode: ±0.225% of calibrated span.
For URV below reference point (300 psi), effect equals:

 300 psi 
 or
 span psi 
 0.125  0.10 



Stability (At Reference Conditions)
±0.025% of URL per year.
Damping Time Constant
Adjustable from 0 to 32 seconds digital damping.
5
 21 bar 
 in % of span.
 span bar 
 0.125  0.10 
Performance specifications are based on reference conditions of 25C (77F), zero (0) static pressure, 10 to 55% RH, and 316 Stainless Steel barrier
diaphragm.
SMV 3000 Smart Multivariable Flow Transmitter
15
SMV 3000 Specifications, continued
Performance Under Rated Conditions - Process Temperature Measurement
Probe Type
Digital
Accuracy
(Ref.) 6
Rated Range Limits
Operative Range Limits
Standards
C
F
C
F
C
F
±0.6
±1.0
–200 to 450
–328 to 842
–200 to 850
–328 to 1562
DIN 43760
E
±1.0
±1.8
0 to 1,000
32 to 1,832
–200 to 1,000
–328 to 1,832
IEC584.1
J
±1.0
±1.8
0 to 1,200
32 to 2,192
–200 to 1,200
–328 to 2,192
IEC584.1
K
±1.0
±1.8
–100 to 1,250
–148 to 2,282
–200 to 1,370
–328 to 2,498
IEC584.1
T
±1.0
±1.8
–100 to 400
–148 to 752
–250 to 400
–418 to 752
IEC584.1
RTD
Platinum 100ohm
Thermocouple
6
Add ±0.025% of calibrated span for transmitter operating in analog mode.
Parameter
Adjustment Range
Output D/A Accuracy
Minimum Span
Description
Select zero and span output for any input from 0% to +100% of the upper
range limit (operative limit) shown above for each probe type. Specifications
only apply to rated limit.
±0.025% of span.
±10C
In Analog Mode
In Digital Mode
Total Reference Accuracy
= Digital Accuracy + Output D/A Accuracy
= Digital Accuracy
• Accuracy includes residual error after
averaging successive readings.
Combined Zero and Span Temperature In Digital Mode:
Effect
RTD
= None
Thermocouple  ±0.10% of input mV per 28C (50F) ±CJ Rejection
In Analog Mode:
Add ±0.15% of calibrated span to calculation for digital mode above.
Cold Junction Rejection
40 to 1
Thermocouple Burnout
Burnout (open lead) detection is user selectable: ON = upscale or downscale
failsafe action with critical status message for any open lead.
Drift (At Reference Conditions)
±1.0C (1.8F) per year.
Damping Time Constant
Adjustable from 0 to 102 seconds digital damping.
Performance Under Rated Conditions - Flowrate Calculation
Mass Flowrate Accuracy
±1.0% of mass flowrate over an 8:1 flow range (64:1 DP range) for steam, air and liquids for a ASME MFC3M - ISO 1567
Orifice meter with flange taps.
Performance Under Rated Conditions - General
Parameter
Description
Output (two-wire)
Analog 4 to 20 mA or digital (DE protocol).
Power Supply Voltage Effect
0.005% of span per volt.
16
SMV 3000 Smart Multivariable Flow Transmitter
SMV 3000 Specifications, continued
Physical
Parameter
Description
Barrier Diaphragms Material
SMA110
SMA125
SMG170
Process Head Material
SMA110
SMA125
SMG170
Vent/Drain Valves & Plugs
1
316L SS
®
®
316L SS, Hastelloy C -2767, Monel 400 8 and Tantalum
®
7
316L SS, Hastelloy C -276
11
Carbon Steel (Zinc-Plated) or 316L SS
®
®10
11
9
Carbon Steel (Zinc-Plated) , 316L SS, Hastelloy C -276 or Monel 400 .
®
11
9
Carbon Steel (Zinc-Plated) , 316L SS, or Hastelloy C -276 .
®
®8
7
316 SS, Hastelloy C-276 , Monel 400
®
Head Gaskets
Glass filled PTFE standard. Viton is optional
Meter Body Bolting
Carbon Steel (Zinc plated) standard. Options include 316 SS, NACE A286
SS bolts and 304 SS nuts and B7M.
Optional Adapter Flange and Bolts
Adapter Flange materials include 316L SS, Hastelloy C-276 and Monel
®
400
DC
Electronic Housing
. Bolt material for flanges is dependent on process head bolts material
®
®
200 Silicone oil or CTFE (Chlorotrifluoroethylene).
Epoxy-polyester hybrid paint
Low Copper-Aluminum. Meets NEMA 4X (watertight) and NEMA 7
(explosion-proof).
1/4-inch NPT (Option 1/2-inch NPT with adapter).
Accepts up to 16 AWG (1.5 mm diameter).
See Figure 8.
5.3 Kg (11.6 lb)
See Figure 9.
Process Connections
Wiring
Dimensions
Net Weight
Mounting
®
Vent/Drains are sealed with Teflon or PTFE
7
Hastelloy® C-276 or UNS N10276
8
Monel 400® or UNS N04400
9
Hastelloy® C-276 or UNS N10276. Supplied as indicated or as Grade CW12MW, the casting equivalent of Hastelloy® C-276
10
Monel 400® or UNS N04400. Supplied as indicated or as Grade M30C, the casting equivalent of Monel 400®
11
9
chosen. Standard adaptor o-ring material is glass-filled PTFE. Viton and
graphite are optional.
Carbon Steel (Zinc-plated) available in angle or flat style.
Mounting Bracket
Fill Fluid
1
®10
Carbon Steel heads are zinc-plated and not recommended for water service due to hydrogen migration. For that service, use 316L stainless steel wetted
Process Heads.
SMV 3000 Smart Multivariable Flow Transmitter
17
Certifications
Type of Protection
Explosionproof:
Class I, Division 1, Groups A, B, C, D
locations
Dust Ignition Proof:
Class II, III, Division 1, Groups E, F,
G locations,
Enclosure Type 4X
Intrinsically Safe:
Class I, II, III, Division 1, Groups A,
B, C, D, E, F, G locations, Enclosure
Type 4X
Comm. Option
All
FM
SM
Approvals
T4 Ta = 93ºC
4-20 mA /
Vmax = 30V
Imax = 225mA
Ci = 4.2nF
Li = *
Pi =1.2W
T4 Ta = 93ºC
Fieldbus – Entity
(Not FISCO)
Vmax = 32V
Imax = 120mA
Ci = 4.2nF
Li = 0
Pi =0.84W
T4 Ta = 40ºC
T3 Ta = 93ºC
Fieldbus – Entity
(Not FISCO)
Vmax = 24V
Imax = 250mA
Ci = 4.2nF
Li = 0
Pi =1.2W
T4 Ta = 40ºC
T3 Ta = 93ºC
FISCO
Vmax = 17.5V
Imax = 380mA
Ci = 4.2nF
Li = 0
Pi =5.32W
T4 Ta = 40ºC
T3 Ta = 93ºC
4-20 mA / DE
Vmax = 42.4V
Imax = 225mA
Ci = 4.2nF
Li = *
Pi =1.2W
T4 Ta = 93ºC
4-20 mA / HART
Vmax = 30V
Imax = 225mA
Ci = 4.2nF
Li = *
Pi =1.2W
T4 Ta = 93ºC
Fieldbus – Entity
(Not FNICO)
Vmax = 32V
Imax = 120mA
Ci = 4.2nF
Li = 0
Pi =0.84W
T4 Ta = 40ºC
T3 Ta = 93ºC
Fieldbus – Entity
(Not FNICO)
Vmax = 24V
Imax = 250mA
Ci = 4.2nF
Li = 0
Pi =1.2W
T4 Ta = 40ºC
T3 Ta = 93ºC
Vmax = 32V
Ci = 4.2nF
Li = 0
T4 Ta = 40ºC
T3 Ta = 93ºC
Class I, Division 2, Groups A, B, C, D
locations, Enclosure Type 4X
Nonincendive:
Class I, Division 2, Groups A, B, C,
D;
Suitable for:
Class II, Division 2, Groups F&G;
Class III, Division 2;
Class I, Zone 2, Group IIC,
Enclosure Type 4X / IP 66/67
Li = 0 except Li = 150µH when Option ME, Analog Meter, is selected.
FM Approvals
SM
is a service mark of FM Global
T5 Ta = 93ºC
4-20 mA / DE
Class 1, Zone 0, AEx ia Group IIC,
Enclosure Type 4X / IP 66/67
Nonincendive:
All
Temp. Codes
Vmax = 42.4V
Imax = 225mA
Ci = 4.2nF
Li = *
Pi =1.2W
Intrinsically Safe:
Class I, II, III, Division 1, Groups A,
B, C, D, E, F, G locations;
Field Parameters
FNICO
18
SMV 3000 Smart Multivariable Flow Transmitter
Type of Protection
Comm. Option
Explosion Proof: Class I, Division
1, Groups B, C, D locations
Dust Ignition Proof: Class II, III,
Division 1, Groups E, F, G
locations,
Enclosure Type 4X
All
Canadian
Standards
Association
(CSA)
Canadian Registration Number
(CRN):
T4 Ta = 93ºC
4-20 mA / DE
T4 Ta = 93ºC
4-20 mA / HART
Vmax = 42V
Imax = 225mA
Ci = 4.2nF
Li = *
Pi =1.2W
T4 Ta = 93ºC
Fieldbus – Entity
(Not FISCO)
Vmax = 24V
Imax = 250mA
Ci = 4.2nF
Li = 0
Pi =1.2W
T4 Ta = 40ºC
T3 Ta = 93ºC
4-20 mA / DE
Vmax = 42.4V
Imax = 225mA
Ci = 4.2nF
Li = *
Pi =1.2W
T4 Ta = 93ºC
4-20 mA / HART
Vmax = 30V
Imax = 225mA
Ci = 4.2nF
Li = *
Pi =1.2W
T4 Ta = 93ºC
Fieldbus – Entity
(Not FNICO)
Vmax = 24V
Imax = 250mA
Ci = 4.2nF
Li = 0
Pi =1.2W
T4 Ta = 40ºC
T3 Ta = 93ºC
Nonincendive:
Class I, Division 2, Groups A, B, C,
D locations, Enclosure Type 4X
All
Temp. Codes
Vmax = 42V
Imax = 225mA
Ci = 4.2nF
Li = *
Pi =1.2W
Intrinsically Safe:
Class I, II, III, Division 1, Groups A,
B, C, D, E, F, G locations,
Enclosure Type 4X
Field Parameters
All ST 3000 models except STG19L, STG99L, STG170 and STG180
have been registered in all provinces and territories in Canada and are
marked CRN: 0F8914.5C.
* Li = 0 except Li = 150µH when Option ME, Analog Meter, is selected.
SMV 3000 Smart Multivariable Flow Transmitter
Type of Protection
19
Comm. Option
Field Parameters
Flameproof, Zone 1:
All
All
Ex d IIC, Enclosure IP 66/67
IECEx
International
Electrotechnical
Commission
(LCIE)
T5 Ta = –50 to 93ºC
T6 Ta = –50 to 78ºC
4-20 mA / DE
Ui = 30V
Ii = 100mA
Ci = 4.2nF
Li = *
Pi =1.2W
T4 Ta = –50 to 93ºC
T5 Ta = –50 to 85ºC
T6 Ta = –50 to 70ºC
4-20 mA / HART
Ui = 30V
Ii = 100mA
Ci = 4.2nF
Li = *
Pi =1.2W
T4 Ta = –50 to 93ºC
T5 Ta = –50 to 63ºC
T6 Ta = –50 to 48ºC
Fieldbus
(Not FISCO)
Ui = 24V
Ii = 250mA
Ci = 4.2nF
Li = 0
Pi =1.2W
T3 Ta = –50 to 93ºC
T4 Ta = –50 to 40ºC
Intrinsically Safe, Zone 0/1:
Ex ia IIC, Enclosure IP 66/67
Temp. Codes
*Li = 0 except Li = 150µH when Option ME, Analog Meter, is selected.
Type of Protection
Flameproof, Zone 1:
Ex d IIC, Enclosure IP 66/67
Intrinsically Safe, Zone 0/1:
Ex ia IIC, Enclosure IP 66/67
SAEx
(South Africa)
Comm. Option
All
Intrinsically Safe, Zone 0/1:
Ex ia IIC, Enclosure IP 66/67
The user must determine the type of
protection required for installation of the
equipment. The user shall then check the
box [√] adjacent to the type of protection
used on the equipment certification
nameplate. Once a type of protection has
been checked on the nameplate,
subsequently the equipment shall not be
reinstalled using any of the other
certification types.
*Li = 0 except Li = 150µH when Option ME, Analog Meter, is selected.
All
Temp. Codes
T5 Ta = –50 to 93ºC
T6 Ta = –50 to 78ºC
4-20 mA / DE
Ui = 30V
Ii = 100mA
Ci = 4.2nF
Li = *
Pi =1.2W
T4 Ta = –50 to 93ºC
T5 Ta = –50 to 85ºC
T6 Ta = –50 to 70ºC
4-20 mA / HART
Ui = 30V
Ii = 100mA
Ci = 4.2nF
Li = *
Pi =1.2W
T4 Ta = –50 to 93ºC
T5 Ta = –50 to 63ºC
T6 Ta = –50 to 48ºC
Fieldbus
(Not FISCO)
Ui = 24V
Ii = 250mA
Ci = 4.2nF
Li = 0
Pi =1.2W
T3 Ta = –50 to 93ºC
T4 Ta = –50 to 40ºC
4-20 mA / DE
Ui = 30V
Ii = 100mA
Ci = 4.2nF
Li = *
Pi =1.2W
T4 Ta = –50 to 93ºC
T5 Ta = –50 to 85ºC
T6 Ta = –50 to 70ºC
4-20 mA / HART
Ui = 30V
Ii = 100mA
Ci = 4.2nF
Li = *
Pi =1.2W
T4 Ta = –50 to 93ºC
T5 Ta = –50 to 63ºC
T6 Ta = –50 to 48ºC
Fieldbus
(Not FISCO)
Ui = 24V
Ii = 250mA
Ci = 4.2nF
Li = 0
Pi =1.2W
T3 Ta = –50 to 93ºC
T4 Ta = –50 to 40ºC
Multiple Marking:
Flameproof, Zone 1:
Ex d IIC, Enclosure IP 66/67
Field Parameters
20
SMV 3000 Smart Multivariable Flow Transmitter
Type of Protection
Flameproof, Zone 0:
, Ex tD
Enclosure IP 66/67
Flameproof, Zone 1:
, Ex d IIC, Ex tD
Enclosure IP 66/67
Comm. Option
Field Parameters
All
All
A20 IP6X T95ºC Ta = 93ºC
or T80ºC Ta = 78ºC
All
All
T5 Ta = –50 to +93ºC
T6 Ta = –50 to +78ºC,
A21 IP6X T95ºC Ta = 93ºC
or T80ºC Ta = 78ºC
4-20 mA / DE
Ui = 30V
Ii = 100mA
Ci = 4.2nF
Li = *
Pi =1.2W
T4 Ta = –50 to 93ºC
T5 Ta = –50 to 85ºC
T6 Ta = –50 to 70ºC
4-20 mA / HART
Ui = 30V
Ii = 100mA
Ci = 4.2nF
Li = *
Pi =1.2W
T4 Ta = –50 to 93ºC
T5 Ta = –50 to 63ºC
T6 Ta = –50 to 48ºC
Fieldbus
(Not FISCO)
Ui = 24V
Ii = 250mA
Ci = 4.2nF
Li = 0
Pi =1.2W
T3 Ta = –50 to 93ºC
T4 Ta = –50 to 40ºC
4-20 mA / DE
Ui = 30V
Ii = 100mA
Ci = 4.2nF
Li = *
Pi =1.2W
T4 Ta = –50 to 93ºC
T5 Ta = –50 to 85ºC
T6 Ta = –50 to 70ºC
4-20 mA / HART
Ui = 30V
Ii = 100mA
Ci = 4.2nF
Li = *
Pi =1.2W
T4 Ta = –50 to 93ºC
T5 Ta = –50 to 63ºC
T6 Ta = –50 to 48ºC
Fieldbus
(Not FNICO)
Ui = 24V
Ii = 250mA
Ci = 4.2nF
Li = 0
Pi =1.2W
T3 Ta = –50 to 93ºC
T4 Ta = –50 to 40ºC
4-20 mA / DE
Ui = 30V
Ii = 100mA
Ci = 4.2nF
Li = *
Pi =1.2W
T4 Ta = –50 to 93ºC
T5 Ta = –50 to 85ºC
T6 Ta = –50 to 70ºC
4-20 mA / HART
Ui = 30V
Ii = 100mA
Ci = 4.2nF
Li = *
Pi =1.2W
T4 Ta = –50 to 93ºC
T5 Ta = –50 to 63ºC
T6 Ta = –50 to 48ºC
Fieldbus
(Not FISCO/FNICO)
Ui = 24V
Ii = 250mA
Ci = 4.2nF
Li = 0
Pi =1.2W
T3 Ta = –50 to 93ºC
T4 Ta = –50 to 40ºC
Intrinsically Safe, Zone 0/1:
, Ex ia IIC,
Enclosure IP 66/67
ATEX
(LCIE)
Non-Sparking, Zone 2:
,Ex nA IIC
(Honeywell),
Enclosure IP 66/67
Multiple Marking:
Flameproof, Zone 1:
, Ex d IIC
Intrinsically Safe, Zone 0/1:
, Ex ia IIC
Non-Sparking, Zone 2:
, Ex nA IIC
Temp. Codes
NOTE: The user must determine the
type of protection required for
installation of the equipment. The user
shall then check the box [ √ ] adjacent to
the type of protection used on the
equipment certification nameplate.
Once a type of protection has been
checked on the nameplate,
subsequently the equipment shall not be
reinstalled using any of the other
certification types.
*Li = 0 except Li = 150µH when Option ME, Analog Meter, is selected.
SMV 3000 Smart Multivariable Flow Transmitter
Type of Protection
21
Comm. Option
Field Parameters
Temp. Codes
All
All
T5 Ta = –50 to 93ºC
T6 Ta = –50 to 78ºC
Flameproof, Zone 1:
BR-Ex d IIC
Enclosure IP 66/67
INMETRO
(CERTUSP)
Brazil
T4 Ta = –50 to 93ºC
T5 Ta = –50 to 85ºC
T6 Ta = –50 to 70ºC
4-20 mA / HART
Ui = 30V
Ii = 100mA
Ci = 4.2nF
Li = *
Pi =1.2W
T4 Ta = –50 to 93ºC
T5 Ta = –50 to 63ºC
T6 Ta = –50 to 48ºC
Fieldbus
(Not FISCO)
Ui = 24V
Ii = 250mA
Ci = 4.2nF
Li = 0
Pi =1.2W
T3 Ta = –50 to 93ºC
T4 Ta = –50 to 40ºC
Intrinsically Safe, Zone 0/1:
BR-Ex ia IIC
Enclosure IP 66/67

4-20 mA / DE
Ui = 30V
Ii = 100mA
Ci = 4.2nF
Li = *
Pi =1.2W
Li = 0 except Li = 150µH when Option ME, Analog Meter, is selected.
This certificate defines the certifications covered for the ST 3000 Pressure Transmitter family of
products, including the SMV 3000 Smart Multivariable Transmitter. It represents the compilation of
the five certificates Honeywell currently has covering the certification of these products into marine
applications.
For ST 3000 Smart Pressure Transmitter and SMV 3000 Smart Multivarible Transmitter
American Bureau of Shipping (ABS) - 2009 Steel Vessel Rules 1-1-4/3.7, 4-6-2/5.15, 4-8-3/13 &
ST 3000 Pressure
13.5, 4-8-4/27.5.1, 4-9-7/13. Certificate number: 04-HS417416-PDA
Transmitter Marine
Certificate
Bureau Veritas (BV) - Product Code: 389:1H. Certificate number: 12660/B0 BV
(MT Option)
Det Norske Veritas (DNV) - Location Classes: Temperature D, Humidity B, Vibration A, EMC B,
Enclosure C. For salt spray exposure; enclosure of 316 SST or 2-part epoxy protection with 316
SST bolts to be applied. Certificate number: A-11476
Korean Register of Shipping (KR) - Certificate number: LOX17743-AE001
Lloyd's Register (LR) - Certificate number: 02/60001(E1) & (E2)
22
SMV 3000 Smart Multivariable Flow Transmitter
The ST 3000 Smart Pressure Transmitters are in conformity with the essential requirements of the Pressure
Equipment Directive.
Honeywell ST 3000 Smart Pressure Transmitters are designed and manufactured in accordance with the
applicable portions of Annex I, Essential Safety Requirements, and sound engineering practices. These
transmitters have no pressurized internal volume, or have a pressurized internal volume rated less than 200 bar
(2,900 psig), and/or have a maximum volume of less than 0.1 liter (Article 3, 1.1.(a) first indent, Group 1 fluids).
Therefore, these transmitters are not subject to the essential requirements of the directive 97/23/EC (PED,
Annex I) and shall not have the CE mark applied.
European
Pressure
Equipment
Directive (PED)
(97/23/EC)
For transmitters rated > 200 bar (2,900 psig) < 1,000 bar (14,500 psig) Honeywell maintains a technical file in
accordance with Annex III, Module A, (internal production control) when the CE mark is required. Transmitter
Attachments: Diaphragm Seals, Process Flanges and Manifolds comply with Sound Engineering Practice.
NOTE: Pressure transmitters that are part of safety equipment for the protection of piping (systems) or
vessel(s) from exceeding allowable pressure limits, (equipment with safety functions in accordance with
Pressure Equipment Directive 97/23/EC article 1, 2.1.3), require separate examination.
A formal statement from TÜV Industry Service Group of TÜV America, Inc., a division of TÜV Süddeutschland,
a Notified Body regarding the Pressure Equipment Directive, can be found at www.honeywell.com. A hard
copy may be obtained by contacting a Honeywell representative.
Electro Magnetic Compatibility (EMC) (2004/108/EC)
CE Mark
All Models: EN 50081-1: 1992; EN 50082-2:1995; EN 61326-1:1997 + A1, A2, and A3 – Industrial Locations
Dual Seal Certification based on ANSI/NFPA 70-202 and ANSI/ISA 12.27.01 requirements without the use of
additional seal protection elements.
Dual Seal
Certification
Recommended
Frequency of
Calibration
Honeywell recommends verifying the calibration of these devices once every four years.
Approved
Manufacturing
Locations
Honeywell Process Solutions - York, PA USA
Honeywell (Tianjin) Limited – Tianjin, P.R. China
Honeywell Automation India Ltd. – Pune 411013 India
®
Hastelloy C-276 is a registered trademark of Haynes International.
®
Monel 400 is a registered trademark of Special Metals Corporation.

ST 3000

and Experion are registered trademarks of Honeywell International Inc.
®
Viton is a registered trademark of DuPont
Teflon
DC
®
®
is a registered trademark of DuPont.
200 is a registered trademark of Dow Corning.
FM Approvals
SM
is a service mark of FM Global
SMV 3000 Smart Multivariable Flow Transmitter
23
Mounting
Reference Dimensions:
millimeters
inches
190,5
7.5
108
4.25
82,5
3.25
114
4.49
with output meter
115
4.53
29
1.14
21
0.83
Minimum
clearance for
cap removal
(both ends)
136
5.35
68
2.68
115
4.53
231,9
9.13
73,6
2.9
Optional
Adapters
Process heads have 1/4-inch
NPT connections.
Optional Adapters have 1/2-inch
NPT connections.
Connections at Optional Adapters
are offset from center (1, 5 mm/0.06 in.).
Distance between process connections
can be configured to:
27,4
1.079
49,3
1.94
98,6
3.88
Figure 8 —Approximate Mounting Dimensions for Reference Only.
Optional
Integral
Meter
Optional
Flange
Adapter
Figure 9 —Examples of Typical Mounting Positions.
24
SMV 3000 Smart Multivariable Flow Transmitter
Options

Angle Mounting Bracket – (Options MB, MX, SB, SX

Laminar Flow Element - (Option LF)
and FB)
The angle mounting bracket is available in either
carbon steel or stainless steel and is suitable for
horizontal or vertical mounting on a two inch
(50mm) pipe, as well as wall mounting. An
optional flat mounting bracket is also available in
carbon steel for 2 inch (50mm) pipe mounting.
An option also exists for Marine approved
mounting brackets used with the Marine
certification options.

Convert standard 1/4 inch NPT connections to 1/2
inch NPT. Available in Stainless Steel, Hastelloy C
and Monel with CS, 316SS, B7M or NACE A286
bolts.







Certificate confirming that the SMV 3000 has been
leak tested to 4,500 psi.


Additional Warranty - (Options W1 - W4)
Standard warranty for the SMV 3000 is 1 year after
delivery. The extended warranty options allow the
SMV 3000 to be warranted for up an additional 4
years.
Multivariable Tx. Configuration - (Option MC)
Allows you to have the SMV 3000 configured at
the factory based on your application. Includes
range configuration for DP, AP, Temp. and
Compensated Flowrate. The MC form must be
completed at time of order.

NACE Nuts and Bolts - (Option CR)
Standard head nuts and bolts for the SMV 3000
are carbon steel. CR option supplies A286SS
bolts and 302/304SS nuts for environments that
are corrosive to carbon steel. 316SS bolts for
adapters supplied when ordered.
Oxygen Cleaned Transmitter - (Option OX)
Over-Pressure Leak Test - (Option TP)
Custom Calibration - (Option CC)
Standard calibration for SMV 3000 includes:
0 - 100 inH2O for DP, 0 - 125 psia for AP and 328 to 852oF. for a Pt. 100 Ohm RTD input.
Custom calibration allows you to have the
factory calibrate the SMV 3000 based on your
application. The CC - Custom Calibration form
must be completed at time of order.
Customer Tag - (Option TG)
Insures that the SMV 3000 has been cleaned of
hydrocarbons so that it can be used in applications
such as oxygen and chlorine service.
Head Gaskets - (Option VT)
Replaces standard PTFE head gaskets with
Viton.
Write Protection – (Options WP, WX)
This stainless steel tag connected to the SMV 3000
via wire allows you to specify information - 4 lines
with 28 characters per line maximum.
SS Center Vent/Drain and Bushing - (Option CV)
Allows a special bushing on side and end ventdrain plugs.
Conduit Adapters - (Options A1, A2)
A jumper on the SMV 3000’s main board is
activated so that the configuration database, as
delivered from the factory, is in "read-only" and
cannot be changed with WX. The WP option allows
configuration changes when delivered from the
factory.
Side Vent/Drain - (Option SV)
Replaces standard End Vent/Drain plugs with
side vent/drain plugs.
Converts standard 1/2 inch NPT Electrical Conduit
Entry to M20 or 3/4 inch NPT. Adapters are 316
SS.

Lightning Protection - (Option LP)
A terminal block with circuitry that protects the
transmitter from transient surges induced by
nearby lightning strikes. This does not provide
protection for RTD or thermocouple wiring.
Adapter Flanges - (Options S2, S3, S4, S5, T2, T3,
V2, V3)


Indicating Meter – (Options ME and SM)
An analog or digital meter is available with 0 to 10
square root or 0 to 100% linear scale.

Provides a SMV 3000 transmitter with specific mass
flow equations supporting the Meriam Laminar Flow
Element for applications such as combustion air.

Calibration Test Report - (Option F1)
Provides document stating calibration points for
all measured variables.

NACE Certificate - (Options F7, FG)
Provides documentation verifying that either
Process-wetted parts only (FG) or both processwetted and non-wetted parts (F7) conform to
NACE specifications.
SMV 3000 Smart Multivariable Flow Transmitter
25
Model Selection Guides are subject to change and are inserted into the specifications as guidance only.
Prior to specifying or ordering a model check for the latest revision Model Selection Guides which are published at:
http://hpsweb.honeywell.com/Cultures/en-US/Products/Instrumentation/ProductModelSelectionGuides/default.htm
SMV 3000 Model Selection Guide
34-ST-16U-51
Issue 22
Page 1 of 4
SMV 3000 Smart Multivariable
Flow Transmitter
Model Selection Guide
Differential Pressure, Static Pressure,
Process Temperature & Flowrate
Instructions
●
●
●
●
Select the desired Key Number. The arrow to the right marks the selection available.
Make one selection from each table, I and II, using the column below the proper arrow.
Select as many Table III options as desired (if no options are desired, specify 00).
A dot (●) denotes unrestricted availability. A letter denotes restricted availability.
Restrictions follow Table IV.
Key Number
______
I
-
___
II
-
III (Optional)
_____
KEY NUMBER
Differential Pressure Range
0-1" / 25" H20
0-2.5 to 0-62.5 mbar
0-1" / 400" H20
0-2.5 to 0-1,000 mbar
0-1" / 400" H20
0-2.5 to 0-1,000 mbar
-
_ _, _ _, _ _
IV
-
Pressure Range
0-100 psia (7.0 bara)
0-750 psia (52.5 bara)
0-3,000 psig (210 barg)
XXXX
Selection
Availability
SMA110
SMA125
SMG170
See 13:STT-21and 13:STT-35 for temperature probes and thermowells ordering information.
TABLE I - METER BODY
Process Heads
Materials of
Construction
Fill Fluid
Process Head
Configuration
Vent/Drain Valves
and Plugs2
1
316 SS
316L SS
Carbon Steel
1
®
3
316 SS
Carbon Steel
Hastelloy C-276
1
®4
316 SS
Monel 400
Carbon Steel
1
Tantalum
316 SS
Carbon Steel
5
316L SS
316 SS
316 SS
5
®
3
316 SS
316 SS
Hastelloy C-276
5
®4
316 SS
316 SS
Monel 400
5
316 SS
Tantalum
316 SS
®
3, 6
®
3
®
3
Hastelloy C-276
Hastelloy C-276
Hastelloy C-276
®
3, 6
®
3
Tantalum
Hastelloy C-276
Hastelloy C-276
® 4, 7
®4
®4
Monel 400
Monel 400
Monel 400
®
DC 200 Silicone
CTFE
1/4" NPT
1/2" NPT with Adapter (on 1/4" NPT Head)
TABLE II
No Selection
1
Carbon Steel heads are zinc-plated.
Vent/Drains are sealed with Teflon® 9 or PTFE.
Hastelloy® C-276 or UNS N10276
4
Monel 400® or UNS N04400
5
Supplied as 316 SS or as Grade CF8M, the casting equivalent of 316 SS.
6
Supplied as indicated or as Grade CW12MW, the casting equivalent of Hastelloy® C-276
7
Supplied as indicated or as Grade M30C, the casting equivalent of Monel 400®
2
3
Barrier Diaphragms
Selection
A__
B__
C__
D__
E__
F__
G__
H__
J__
K__
L__
_1_
_2_
__A
__H
00000
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
t
t
t
●
●
●
●
●
●
●
●
●
●
●
●
26
SMV 3000 Smart Multivariable Flow Transmitter
SMV 3000 Model Selection Guide (continued)
34-ST-16U-51
Issue 22
Page 2 of 4
Availability
10 25 70
SMX1xx
TABLE III - OPTIONS
Indicating Meter Options
Analog Meter (0-100 Even 0-10 Square Root)
** (0 to 100% digital display only) **
Smart Meter
Transmitter Housing & Electronics Options
Lightning Protection
Custom Calibration and I.D. in Memory
Multivariable Transmitter Configuration
Write Protection (Delivered in the "enabled" position)
Write Protection (Delivered in the "disabled" position)
M20 316 SS Conduit Adaptor
3/4" NPT 316 SS Conduit Adapter
Stainless Steel Customer Wired-On Tag
(4 lines, 28 characters per line, customer supplied information)
Stainless Steel Customer Wired-On Tag (blank)
Laminar Flow Element Software
End Cap Live Circuit Warning Label in Spanish (only with ATEX 3D)
End Cap Live Circuit Warning Label in Portuguse (only with ATEX 3D)
End Cap Live Circuit Warning Label in Italian (only with ATEX 3D)
End Cap Live Circuit Warning Label in German (only with ATEX 3D)
Meter Body Options
316 SS Bolts and 316 SS Nuts for Process Heads
B7M Bolts and Nuts for Process Heads
A286 SS (NACE) Bolts and 304 SS (NACE) Nuts for Heads
5
316 SS Adapter Flange - 1/2" NPT with CS Bolts
5
316 SS Adapter Flange - 1/2" NPT with 316 SS Bolts
5
316 SS Adapter Flange - 1/2" NPT with NACE A286 SS Bolts
5
316 SS Adapter Flange - 1/2" NPT with B7M Bolts
®
3, 6
Adapter Flange - 1/2" NPT with CS Bolts
Hastelloy C-276
®
3, 6
Adapter Flange - 1/2" NPT with 316 SS Bolts
Hastelloy C-276
® 4, 7
Monel 400
Adapter Flange - 1/2" NPT with CS Bolts
® 4, 7
Monel 400
Adapter Flange - 1/2" NPT with 316 SS Bolts
5
316 SS Blind Adapter Flange with CS Bolts
5
316 SS Blind Adapter Flange with 316 SS Bolts
5
316 SS Blind Adapter Flange with NACE A286 SS Bolts
5
316 SS Blind Adapter Flange with B7M Bolts
Side Vent/Drain (End Vent Drain is standard)
316 SS Center Vent Drain and Bushing
®8
Viton Process Head Gaskets (½" adapter gaskets ordered separately)
®8
Viton Adapter Flange Gaskets
Transmitter Mounting Bracket Options
Angle Mounting Bracket - Carbon Steel
Marine Approved Angle Mounting Bracket - Carbon Steel
Angle Mounting Bracket - 304 SS
Marine Approved Angle Mounting Bracket - 304 SS
Flat Mounting Bracket
Selection
ME
SM
p
r
p
r
p
r
LP
CC
MC
WP
WX
A1
A2
●
●
●
●
●
n
u
●
●
●
●
●
n
u
●
●
●
●
●
n
u
TG
●
●
●
TB
LF
SP
PG
TL
GE
●
●
a
a
a
a
●
●
a
a
a
a
●
SS
B7
CR
S2
S3
S4
S5
T2
T3
V2
V3
B3
B4
B5
B6
SV
CV
VT
VF
● ● ●
● ● ●
● ● ●
c c c
c c c
c c c
c c c
c c c
c c c
c c c
c c c
c c c
c c c
c c c
c c c
● ● ●
● ● ●
● ● ●
17 17 17
MB
MX
SB
SX
FB
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
UM
0X
TP
F1
F3
F5
F7
FG
FX
MT
●
j
●
●
●
●
o
●
●
2
●
j
●
●
●
●
o
●
●
2
●
j
●
●
●
●
o
●
●
2
a
a
a
a
b
b
b
b
b
b
b
b
b
Services/Certificates/Marine Type Approval Options
User's Manual Paper Copy
Clean Transmitter for Oxygen or Chlorine Service with Certificate
Over-Pressure Leak Test with F3392 Certificate
Calibration Test Report and Certificate of Conformance (F33208)
Certificate of Conformance (F3391)
Certificate of Origin (F0195)
NACE Certificate (Process-Wetted & Non-Process Wetted) (FC33339)
NACE Certificate (Process-Wetted only) (FC33338)
Material Traceability Certification per EN 10204 3.1 (FC33341)
Marine Type Approvals (DNV, ABS, BV, KR & LR) (FC33340)
3
Hastelloy® C-276 or UNS N10276
Monel 400® or UNS N04400
5
Supplied as 316 SS or as Grade CF8M, the casting equivalent of 316 SS.
6
Supplied as indicated or as Grade CW12MW, the casting equivalent of Hastelloy® C-276
7
Supplied as indicated or as Grade M30C, the casting equivalent of Monel 400®
8
Viton® or Fluorocarbon Elastomer
4
b
b
SMV 3000 Smart Multivariable Flow Transmitter
27
SMV 3000 Model Selection Guide (continued)
Issue 22
Page 3 of 4
SMX1xx
TABLE III - OPTIONS (continued)
Warranty Options
Additional Warranty - 1 year
Additional Warranty - 2 years
Additional Warranty - 3 years
Additional Warranty - 4 years
Availability
10 25 70
Selection
●
●
●
●
●
●
●
●
●
●
●
●
9X
●
●
●
1C
●
●
●
W1
W2
W3
W4
b
TABLE III - OPTIONS (continued)
Approval
Body
None
FM
ApprovalsSM
Approval Type
None
Explosion Proof
Dust Ignition Proof
Suitable for use in
Non-Incendive
Intrinsically Safe
Canadian
Standards
Association
(CSA)
Explosion Proof
Dust Ignition Proof
Suitable for use in
Intrinsically Safe
Flameproof, Zone 1
IECEx
Intrinsically Safe,
Zone 0/1
Intrinsically Safe Zone
0/1
Flameproof, Zone 1
ATEX10
(LCIE)
Non-Sparking
Zone 2
Multiple Marking
11
Int. Safe, Zone 0/1, or
Flameproof, Zone 1, or
Non-Sparking, Zone 2
Intrinsically Safe,
Zone 0/1
SAEx
Flameproof, Zone 1
(South Africa) Multiple Marking 11
Int. Safe, Zone 0/1, or
Flameproof, Zone 1
10
Selection
Location or Classification
Class I, Div. 1, Groups A,B,C,D
Class II, Div. 1, Groups E,F,G
Class III, Div. 1
Class I, Div. 2, Groups A,B,C,D
Class I, II, III, Div. 1, Groups
A,B,C,D,E,F,G
- - T4 at Ta < 93oC
Class I, Div. 1, Groups B,C,D
Class II, III, Div. 1, Groups E,F,G
Class I, II, III, Div. 2, Groups
A,B,C,D,E,F,G
Class I, II, III, Div. 1, Groups
b
2J
●
●
●
CA
●
●
●
3S
●
●
●
3D
●
●
●
3N
●
●
●
Ex II 1 G Ex ia IIC T4, T5, T6
Ex II 2 G Ex d IIC T5, T6
Ex II 3 G Ex nA, IIC T6 (Honeywell)
Enclosure IP 66/67
3H
●
●
●
Ex ia IIC T4, T5, T6
Z2
●
●
●
EX d IIC T5, T6 Enclosure IP 66/67
Ex ia IIC T4, T5, T6
Ex d IIC T5, T6
Enclosure IP 66/67
ZD
●
●
●
ZA
●
●
●
-
A,B,C,D,E,F,G
o
T4 at Ta < 93 C
Ex d IIC; T5 (Ta = -40 to +93ºC), T6 (Ta = -40 to
+78ºC)
Ex ia IIC; T3, T4, T5 , T6. See Spec for detailed
temperature codes by Communications option.
Ex ia IIC T5
Ex d IIC T6,
Enclosure IP 66/67
Ex nA, IIC T6
Vmax = 42 Vdc
T4 at Ta = 930C
T5 at Ta = 800C
T6 at Ta = 650C
(Honeywell). Enclosure IP 66/67
See ATEX installation requirements in the ST 3000 User's Manual
The user must determine the type of protection required for installation of the equipment. The user shall then check the box [√]
adjacent to the type of protection used on the equipment certification nameplate. Once a type of protection has been checked on
the nameplate, subsequently the equipment shall not be reinstalled using any of the other certification types.
11
28
SMV 3000 Smart Multivariable Flow Transmitter
SMV 3000 Model Selection Guide (continued)
34-ST-16U-51
Issue 22
Page 4 of 4
TABLE IV
Factory Identification
XXXX
●
●
●
RESTRICTIONS
Restriction
Letter
Table
Not Available With
Available Only With
Selection
Table
Selection
3D or 3H
Select only one option from this group.
__H
a
b
c
III
j
n
o
p
I
_2_
III
CR, S4 or B5
r
III
Display is 0-100% only. No other smart
functions available with this option.
t
u
2
17
III
III
III
III
S2, T2 or V2
1C, 2J
MX, SX
VT
I
III
III
1C, 2J
Functions in the analog mode only.
III
Ordering Example: SMA125-E1A-00000-MB,MC,1C + XXXX
Hastelloy® is a registered trademark of Haynes International
Monel 400® is a registered trademark of Special Metals Corporation.
HART® is a registered trademark of HART Communication Foundation.
FOUNDATIONTM Fieldbus is a registered trademark of Fieldbus Foundation.
Viton® is a registered trademark of DuPont Performance Elastomers.
FM ApprovalsSM is a service mark of FM Global
DC® 200 is a registered trademark of Dow Corning
Teflon® is a registered trademark of DuPont.
FB, MB, SB
SMV 3000 Smart Multivariable Flow Transmitter
29
Ordering information
For application assistance, current specifications, pricing, or name of the nearest Authorized Distributor, contact one of the
offices below. Or, visit Honeywell on the World Wide Web at: http://www.honeywell.com.
ASIA PACIFIC
Bulgaria
Honeywell EOOD
Phone: +(359) 2 40 20 900
FAX: +(359) 2 40 20 990
Slovak Republic
Honeywell s.r.o.
Phone: +421-2-58247 410
FAX: +421-2-58247 415
Czech Republic
Honeywell spol. s.r.o.
Phone: +420 242 442 232
FAX: +420 242 442 131
Spain
Honeywell S.A.
Phone: +34 (0)91313 61 00
FAX: +34 (0)91313 61 30
Denmark
Honeywell A/S
Phone: +(45) 39 55 55 55
FAX: +(45) 39 55 55 58
Sweden
Honeywell AB
Phone: +(46) 8 775 55 00
FAX: +(46) 8 775 56 00
Finland
Honeywell OY
Phone: +358 (0) 20752 2753
FAX: +358 (0) 20752 2751
Switzerland
Honeywell AG
Phone: +41 18552448
FAX: +(41) 1 855 24 45
France
Honeywell SA
Phone: +33 (0)1 60198075
FAX: +33 (0)1 60198201
Turkey
Honeywell Turkey A.S.
Phone: +90 216 578 71 00
FAX: +90 216 575 66 35
Thailand
Honeywell Systems
(Thailand) Ltd.
Phone: +(662) 693-3099
FAX: +(662) 693-3089
Germany
Honeywell AG
Phone: +49 (69)8064-299
FAX: +49 (69)806497336
Ukraine
Honeywell
Tel: +380-44-201 44 74
Fax: +380-44-201-44-75
Taiwan R.O.C.
Honeywell Taiwan Ltd.
Phone: +(886-2) 2245-1000
FAX: +(886-2) 2245-3241
Hungary
Honeywell Kft.
Phone: +36-1-451 4300
FAX: +36-1-451 4343
United Kingdom
Honeywell Control Systems
Ltd.
Phone: +44 (0)1344 655251
FAX: +44 (0) 1344 655554
SE Asia Countries
Italy
Honeywell S.p.A.
Phone: +39 02 92146 307/
395
FAX: +39 0292146377
Control Products
Asia Pacific Headquarters
Phone: +(65) 6355-2828
Fax: +(65) 6445-3033
New Zealand
Honeywell Limited
Phone: +(64-9) 623-5052
Fax: +(64-9) 623-5060
Toll Free (0800) 202-088
Asia Pacific Global
Technical Support
Philippines
Honeywell Systems
(Philippines) Inc.
Phone: +(63-2) 633-2830-31/
636 1661-62
Fax: +(63-2) 638-4013
Field Instruments
Phone: +65 6580 3156
Fax: +65 6445-3033
Process Instruments
Phone: (603) 76950 4777
Fax: (603) 7958 8922
Australia
Honeywell Limited
Phone: +(61) 7-3846 1255
FAX: +(61) 7-3840 6481
Toll Free 1300-36-39-36
Toll Free Fax:
1300-36-04-70
China – PRC - Beijing
Honeywell China Inc.
Phone: +(86-10) 8458-3280
Fax: +(86-10) 8458-4650
China – PRC - Shanghai
Honeywell China Inc.
Phone: (86-21) 5257-4568
Fax: (86-21) 6237-2826
China – PRC - Chengdu
Honeywell China Inc.
Phone: +(86-28) 8678-6348
Fax: +(86-28) 8678-7061
China – PRC - Xi’an
Honeywell China Ltd - Xi’an.
Phone: +(86-29) 8833-7490
Fax: +(86-29) 8833-7489
China – PRC - ShenzhenHoneywell China Inc.
Phone: +(86) 755-2518-1226
Fax: +(86) 755-2518-1221
Indonesia
PT Honeywell Indonesia
Phone: +(62) 21-535-8833
FAX: +(62) 21-5367 1008
India
Automation India Ltd.
Honeywell Ltd.
Phone:+(91) 5603-9400
Fax: +(91) 5603-9600
Japan
Honeywell Inc.
Phone: +(81) 3 6730 7150
Fax: +(81) 3 6730 7228
Malaysia
Honeywell Engineering
Sdn Bhd
Phone: +(60-3) 7950-4776
Fax: +(60-3) 7958-8922
Singapore
Honeywell Pte Ltd.
Phone: +(65) 6580 3278
Fax: +(65) 6445-3033
South Korea
Honeywell Korea Co Ltd
Phone: +(822) 799 6315
Fax: +(822) 792 9015
see Honeywell Pte Ltd
(Singapore)
for:
Pakistan
Cambodia
Guam
Laos
Myanmar
Vietnam
East Timor
SE Asia Countries
see Honeywell Automation
India Ltd for:
Bangladesh
Nepal
Sri Lanka
EUROPE
Austria
Honeywell Austria GmbH
Phone: +43 (316)400123
FAX: +43 (316)40017
Belgium
Honeywell SA/NV
Phone: +32 (0) 2 728 24 07
FAX: +32 (0) 2 728 22 45
The Netherlands
Honeywell B.V.
Phone: +31 (0) 20 5656200
FAX: +31 (0) 20 5656210
Norway
Honeywell A/S
Phone: (45) 39 55 55 55
Poland
Honeywell Sp. zo.o
Phone: +48-22-6060900
FAX: +48-22-6060901
Portugal
Honeywell Portugal Lda
Phone: +351 21 424 5000
FAX: +351 21 424 50 99
Romania
Honeywell Bucharest
Phone: +40 (0) 21 2316437
FAX: +40 (0) 21 2316439
Russian Federation (RF),
ZAO "Honeywell"
Phone: +7 (095) 796 98 00
FAX: +7 (495) 797 99 64
Specifications are subject to change without notice.
MIDDLE EAST
Abu Dhabi U A E
Middle East Headquarters
Honeywell Middle East Ltd.
Phone: +971 2 4041246
FAX: +971 2 4432536
Sultanate of Oman
Honeywell & Co Oman LLC
Phone: +968 24 701153/
Ext.33
FAX +968 24 787351
AFRICA
Mediterranean & African
Distributors
Honeywell SpA
Phone: +39 (02) 250 10 604
FAX: +39 (02) 250 10 659
South Africa (Republic of)
and sub saharan
Honeywell Southern Africa
Honeywell S.A. Pty. Ltd.
Phone: +27 11 6958000
FAX +27 118051504
NORTH AMERICA
Canada
Honeywell LTD
Phone: 1-800-737-3360
FAX: 1-800-565-4130
USA
Honeywell Process Solutions,
Phone: 1-800-423-9883
Or 1-800-343-0228
Email: ask-
[email protected]
SOUTH AMERICA
Argentina
Honeywell S.A.I.C.
Phone: +(54-11) 4383-3637
FAX: +(54-11) 4325-6470
Brazil
Honeywell do Brasil & Cia
Phone: +(55-11) 7266-1900
FAX: +(55-11) 7266-1905
Chile
Honeywell Chile, S.A.
Phone: +(56-2) 233-0688
FAX: +(56-2) 231-6679
Mexico
Honeywell S.A. de C.V.
Phone: +(52) 55 5259-1966
FAX: +(52) 55 5570-2985
Saudia Arabia
Honeywell Turki Arabia Ltd
Jubail Office
Phone: +966-3-341-0140
Fax: +966-3-341-0216
Honeywell - ATCO
Dammam Office
Phone: 0096638304584
Fax: 0096638338059
Puerto Rico
Honeywell Inc.
Phone: +(809) 792-7075
FAX: +(809) 792-0053
Kuwait
Honeywell Kuwait KSC
Phone: +965 242 1327 to 30
Fax: +965 242 8315
and
Phone: +965 326 2934/1821
Fax: +965 326 1714
Venezuela
Honeywell CA
Phone: +(58-2) 238-0211
FAX: +(58-2) 238-3391
Trinidad
Honeywell Inc.
Phone: +(868) 624-3964
FAX: +(868) 624-3969
30
SMV 3000 Smart Multivariable Flow Transmitter
For More Information
Learn more about how Honeywell’s SMV 3000
Smart Multivariable Flow Transmitter can increase
performance, reduce downtime and decrease
configuration costs, visit our website
www.honeywell.com/ps or contact
your Honeywell account manager.
Honeywell Process Solutions
1860 West Rose Garden Lane
512 Virginia Drive
Tel: 1-800-423-9883 or 1-800-343-0228
www.honeywell.com/ps
34-SM-03-01
August 2010
© 2010 Honeywell International Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement