Manuel d`utilisation 3M MP8647

Manuel d`utilisation 3M MP8647
Document téléchargé sur www.lampe-videoprojecteur.info
MP8647
Multimedia Projector
Operator's Guide
MP8647 Projecteur multimedia - Guide de L' opérateur
MP8647 Multimedia-Projektor - Benutzerhandbuch
MP8647 Proyector de Multimedia - Guía del usuario
MP8647 Proiettore Multimediale - Guida dell' operatore
MP8647 Multimedia Projector - Gebruiksaanwijzing
MP8647 Projector dos Multimedia - Guia da operador
MP8647 Multimedia Projektør- Brukerhåndbok
Intended Use Statement
Before operating this machine, please read the Operator’s Guide and
Product Safety Guide thoroughly. The 3M™ Multimedia Projectors are
designed, built, and tested for use indoors, using 3M lamps, 3M ceiling
mount hardware, and nominal local voltages. The use of other
replacement lamps, outdoor operation, or different voltages have not
been tested and could damage the projector peripheral equipment and/or
create a potentially unsafe operating condition. 3M Multimedia
projectors are designed to operate in a normal office environment.
• 16° to 29°C (60° to 85° F)
• 10-80 % RH (without condensation)
• 0-1828 m (0-6000 feet) above sea level
The ambient operating environment should be free of airborne smoke,
grease, oil and other contaminates that can affect the operation or
performance of the projector.
Use of this product in adverse conditions will
void the product warranty.
Operator's Guide
Thank you for purchasing this liquid crystal projector.
WARNING • Please read the accompanying manual “Product Safety Guide”
and this “Operator's Guide” thoroughly to ensure correct usage through
understanding. After reading, store this instruction manual in a safe place for
future reference.
NOTE • The information in this manual is subject to change without notice.
• The manufacturer assumes no responsibility for any errors that may appear in this manual
• The reproduction, transmission or use of this document or contents is not permitted without
express written authority.
TRADEMARK ACKNOWLEDGMENT : PS/2, VGA and XGA are registered trademarks of
International Business Machines Corporation. Apple, Mac and ADB are registered trademarks of
Apple Computer, Inc. VESA and SVGA are trademarks of the Video Electronics Standard
Association. Windows is a registered trademark of Microsoft Corporation. Carefully observe the
trademarks and registered trademarks of all companies, even when not mentioned.
CONTENTS
Page
Page
FEATURES .......................................2
BEFORE USE ...................................2
TROUBLESHOOTING ....................20
Contents of Package ..............................2
Part Names.............................................3
Loading the Battery ................................5
Fixing the Handle....................................5
INSTALLATION ................................6
Installation of the Projector and Screen........6
Angle Adjustment ...................................6
Cabling ...................................................7
Power Connection ..................................8
Example of System Setup ......................8
Plug & Play .............................................8
OPERATIONS ...................................9
Power On ...................................................9
Power Off ................................................9
Basic Operation ....................................10
Setup Menu ..........................................12
Input Menu............................................13
Image Menu..........................................14
Options Menu .......................................15
No Signal Menu ....................................16
MAINTENANCE ..............................17
Lamp.....................................................17
Air Filter ................................................19
Other Maintenance ...............................19
Service Infomation................................20
OSD Message ......................................20
Indicators Message ..............................21
Symptom ..............................................22
SPECIFICATIONS...........................23
ACCESSORIES...............................24
TECHNICAL APPENDIX.................25
TABLES
Table 1. Installation Reference.................6
Table 2. Cabling .......................................7
Table 3. Basic Operations ......................10
Table 4. Setup Menu ..............................12
Table 5. Input Menu................................13
Table 6. Image Menu..............................14
Table 7. Options Menu ...........................15
Table 8. No Signal Menu ........................16
Table 9. OSD Message ..........................20
Table 10. Indicator Message ..................21
Table 11. Symptom ................................22
Table 12. Specifications .........................23
.......................................................................................
For "TECHNICAL" and "REGULATORY
NOTICE", see the end of this manual.
ENGLISH-1
ENGLISH
Multimedia Projector
FEATURES
This liquid crystal projector is used to project various computer signals as well as NTSC / PAL /
SECAM video signals onto a screen. Little space is required for installation and large images can
easily be realized.
Outstanding Brightness
The UHB lamp and high-efficiency optical system assure a high level of brightness.
Partial Magnification Function
Interesting parts of images can be magnified for closer viewing.
Distortion Correction Function
Distortion-free images are quickly available.
BEFORE USE
Contents of package
Make sure all of the following items are included in the package. If anything is missing, please
contact your dealer.
NOTE • Keep the original packing material for future reshipment.
Power Cord x 3
S-Video Cable
(US, UK, Europe)
(Mini DIN4-pin)
RGB Cable
Video/Audio Cable
Projector
VIDEO
STANDBY/ON
RGB
MENU
SELECT
MENU
MAGNIFY
POSITION RESET
FREEZE VOLUME
MUTE
OFF
AUTO
TIMER
BLANK
Remote Control
Transmitter
containing Battery
(with white lead)
MP8647
Multimedia Projector
Operator's Guide
MP8647 Projecteur multimedia - Guide de I' opérateur
MP8647 Multimedia-Projektor - Benutzerhandbuch
MP8647 Proyector de Multimedia - Guía del usuario
MP8647 Proiettore Multimediale - Guida dell' operatore
MP8647 Projector dos Multimedia - Guia da operador
MP8647 Multimedia Projector - Gebruiksaanwijzing
Operator's Guide
Product Safety Guide
ENGLISH-2
Mouse cable
(PS/2)
Handle
Part Names
Speaker
Zoom Knob
Focus Ring
Handle Hook
Remote Control Sensor
Power Switch
Lens
Slide Lens Door
Foot Adjuster
FRONT/LEFT VIEW OF
THE PROJECTOR
AC Inlet
(to the Power Cord)
Ventilation Openings
(Intake)
Control Panel (Refer to P.9 "OPERATIONS")
INPUT Button
LAMP Indicator
TEMP Indicator
POWER Indicator
RESET Button
MENU Button
STANDBY/ON Button
MUTE Button
Foot Adjuster Button
Air Filter and Intake
(for the Cooling Fan)
Ventilation Openings
(exhaust)
Rear Foot Adjuster
REAR/RIGHT VIEW OF
THE PROJECTOR
Terminal Panel
(Refer below)
S-VIDEO Terminal
Remote Control Sensor
VIDEO IN Terminal
RGB IN 1 Terminal
AUDIO IN L Terminal
RGB IN 2 Terminal
1
AUDIO IN R Terminal
AUDIO IN
AUDIO 1
IN
VIDEO IN
2 AUDIO OUT
2
RGB IN
S-VIDEO IN
USB
RGB OUT
CONTROL
AUDIO IN 1 Terminal
CONTROL Terminal
AUDIO IN 2 Terminal
RGB OUT Terminal
AUDIO OUT Terminal
USB Terminal
TERMINAL PANEL
ENGLISH-3
ENGLISH
BEFORE USE (continued)
BEFORE USE (continued)
Part Names (continued)
VIDEO Button
STANDBY/ON Button
VIDEO
STANDBY/ON
RGB
RGB Button
MENU SELECT Button
Used to click the left
mouse button.
Button
MENU
SELECT
Used to operate the
mouse shift function .
POSITION Button
MENU
MENU Button
MAGNIFY
Button
OFF
RESET Button
Used to click the right
mouse button.
Button
MAGNIFY
MAGNIFY
POSITION RESET
MAGNIFY
FREEZE VOLUME
Button
MUTE
OFF
AUTO
AUTO Button
TIMER Button
TIMER
BLANK
VOLUME
Button
VOLUME
Button
FREEZE Button
MUTE Button
BLANK Button
Battery Holder
REMOTE CONTROL TRANSMITTER
(Refer to P.9 "OPERATIONS")
These functions work when the mouse control function is activated. Remember, the POSITION,
BLANK ON and MENU ON functions disable the mouse control function.
NOTE To prevent any malfunction;
• Do not exert excessive physical force on the remote control transmitter. Take care not to drop.
• Do not place the heavy objects on the remote control transmitter.
• Do not wet the remote control transmitter or place it on any wet object.
• Do not place the remote control transmitter close to the cooling fan of the projector.
• Do not disassemble the remote control transmitter in case of malfunction. Please send to a
servicing dealer.
ENGLISH-4
BEFORE USE (continued)
ENGLISH
Loading the Battery
First Loading:
In original packing, the battery is installed in the battery
holder of the remote control transmitter with protection
film(the transparent filmsome of which is inside the battery
holder). Pull out the protection film to load the battery.
“+” side
Replacing:
1. See the reverse side of the remote control transmitter.
2. Pinch the groove and pull out battery holder as the
drawing right.
3. Remove the worn battery.
4. Install the new battery (3V micro lithium battery type
no.CR2025) with “+” side facing.
5. Push in and click the battery holder.
Pull out
Battery Holder
CAUTION • Use only the specified batteries with this remote control
transmitter. Also, do not mix new and old batteries. This could cause
battery cracking or leakage, which could result in fire or personal injury.
• When loading the batteries, make sure the plus and minus terminals are
correctly oriented as indicated in the remote control transmitter. Incorrect
orientation could cause battery cracking or leakage, which could result in
personal injury or pollution of the surrounding environment.
• When you dispose the battery, you should obey the law in the relative area or
country.
• Keep the battery away from children and pets.
• When not to be used for an extended period, remove the batteries from the
remote control transmitter.
NOTE Replace the batteries when remote control transmitter operation becomes difficult.
Fixing the Handle
Fix the enclosed handle if you need.
1. Raise up the handle hook, and pass one end of the
handle through the hole of handle hook.
2. Buckle the end of the handle, as the right drawing.
3. Fix the other end of the handle to the other handle
hook in the same way.
1
2
CAUTION Make sure the handle is fixed before carrying the projector with
the handle. If the projector should be dropped from the handle should be off, it
could result in an injury, and continued use could result in fire or electrical shock.
Do not flourish the projector with the handle.
ENGLISH-5
INSTALLATION
Installation of the Projector and Screen
Refer to the drawing and table below for determining the screen size and projection distance.
The projection distances shown in the table below are
Screen
for full size (800 x 600 dots)
a: Distance from the projector to the screen. (±10%)
Table 1 Installation Reference
Screen size
[inches (m)]
a [inches (m)]
Min.
Top View
Max.
40 (1.0)
60 (1.5)
65 (1.7)
98 (2.5)
78 (2.0)
117 (3.0)
80 (2.0)
131 (3.3)
157 (4.0)
100 (2.5)
163 (4.1)
196 (5.0)
120 (3.0)
196 (5.0)
236 (6.0)
150 (3.8)
246 (6.2)
295 (7.5)
200 (5.0)
328 (8.3)
394 (10.0)
Lens center
a
Side View
CAUTION • Install the projector in a suitable environment according to
instructions of the accompanying manual “Product Safety Guide” and this
manual.
• Please basically use liquid crystal projector at the horizontal position. If you use
liquid crystal projector by the lens up position, the lens down position and the side up
position, this may cause the heat inside to build up and cause damage. Be especially
careful not to install it with ventilation holes blocked.
• Do not install LCD projector in smoke effected environment. Smoke residue may
buildup on critical parts (i.e.LCD panel, Lens Assy etc.).
Angle Adjustment
Use the foot adjusters on the bottom of the
projector to adjust the projection angle. It is
variable within 0˚ to 9˚ approximately.
1. Lift up the front side of the projector,
and pressing the foot adjuster button,
adjust the projection angle.
2. Release the button to lock at the desired
angle.
3. Use the rear foot adjuster to adjust the
left-right slope. Do not force the foot
adjuster screws. This could damage the
adjusters or cause the lock to fail.
Foot Adjuster
Press the foot adjuster button
Rear Foot Adjuster
Variable within the range of approximately 0˚-9˚
CAUTION • Do not release the foot adjuster button unless the projector is
being held; otherwise, the projector could overturn or fingers could get
caught and cause personal injury.
ENGLISH-6
INSTALLATION (continued)
ENGLISH
Cabling
Refer to the table below for connecting each terminal of the projector to a device.
Table 2. Cabling
Function
Analog RGB input
Analog RGB output
Audio input
(from the computer)
Terminal
RGB IN 1
RGB IN 2
RGB OUT
Cable
Accessory RGB cable or optional RGB
cable with D-sub 15-pin shrink jack and
inch thread screws
AUDIO IN 1
(interlocked with RGB IN 1)
Optional audio cable with stereo mini jack
AUDIO IN 2
(interlocked with RGB IN 2)
PS/2 mouse control
Accessory PS/2 mouse cable
ADB mouse control
Optional ADB mouse cable
CONTROL
Serial mouse control
Optional Serial mouse cable
RS-232C communication
Optional RS-232C cable
USB mouse control
USB
Optional USB cable
S-video input
S-VIDEO
Accessory S-video cable with mini DIN 4pin jack
Video input
VIDEO IN
Accessory video/audio cable
Audio input
(from video equipment)
AUDIO IN L
AUDIO IN R
Accessory video/audio cable or optional
audio cable with RCA jack
Audio output
AUDIO OUT
Optional audio cable with stereo mini jack
CAUTION • Incorrect connecting could result in fire or electrical shock.
Please read this manual and the separate “Product Safety Guide”.
• Before connecting, turn off to all devices to be connected, except for the USB
cable.
• The cables may have to be used with the core set to the projector side. Use the
cables which are included with the projector or specified.
NOTE • Before connecting, read instruction manuals of the devices to be connected, and make sure that the
projector is compatible with the device.
• Secure the screws on the connectors and tighten.
• For some RGB input modes, the optional Mac adapter is necessary.
• Some computers may have multiple display screen modes. Use of some of these modes will not be possible
with this projector.
• Refer to the “TECNICAL” section for the pin assignment of connectors and RS-232C communication data.
ENGLISH-7
INSTALLATION (continued)
Power Connection
Use the correct power cord depending on the power outlet to be used.
Connect the AC inlet of the projector to the power outlet firmly by the power cord.
CAUTION • Be carful in handling the power
cord according to instructions of the
accompanying manual "Product Safety Guide"
and this manual.
• Connect the power cord firmly. Avoid using a
loose, unsound outlet or failed contact .
Power outlet
Power
Cord
AC Inlet
Example of system setup
Video tape recorder
with S jack
Video tape recorder
Computer
(notebook type)
1
AUDIO IN
AUDIO 1
IN
VIDEO IN
2 AUDIO OUT
RGB IN
RGB Cable
2
S-VIDEO IN
USB
RGB OUT
CONTROL
RS-232C
Cable
Computer
(desktop type)
Speaker (with amplifier)
Display monitor
NOTE • When connecting with a notebook computer, set the proper RGB external image output
(setting CRT display or simultaneous display of LCD and CRT). Please read instruction manual of
the notebook for more information.
Plug & Play
This projector is VESA DDC 1/2B compatible. Plug & play is possible by connecting to a computer
that is VESA DDC (Display Data Channel) compatible.
Please use this function by connecting the accessory RGB cable with RGB IN 1 terminal (DDC
1/2B compatible). Plug & play may not operate by other connections.
NOTE • Plug & play is a system configured with peripheral equipment including a computer,
display and an operating system.
• This projector is recognized as a plug & play monitor. Use the standard display drivers.
• Plug & play may not operate by the computer to connect. Plug & play will not operate in the
connection with Apple computer.
ENGLISH-8
STANDBY/ON Button
POWER Indicator
STANDBY/
ON Button
VIDEO
STANDBY/ON
RGB
MENU
SELECT
MENU
POSITION RESET
Zoom Knob
MAGNIFY
FREEZE VOLUME
Focus Ring
MUTE
OFF
AUTO
Power Switch
TIMER
BLANK
Slide Lens Door
Power ON
1. Check that the power cord is connected correctly.
2. Set the power switch to [ | ]. The standby mode is selected, and the POWER indicator is turned to
orange.
3. Press the STANDBY/ON button
on the control panel or the remote control transmitter.
Warm-up begins and the POWER indicator blinks in green.
4. The POWER indicator ceases blinking and turns to green when power is on. Open the Slide Lens
Door.
5. Adjust picture size using the ZOOM knob.
6. Adjust focus using the FOCUS ring .
Power OFF
1. Press the STANDBY/ON button
on the control panel or the remote control transmitter for
approximately two second. The projector lamp is extinguished and lamp cooling begins. The
POWER indicator blinks orange during lamp cooling. Pressing the STANDBY/ON button
has no effect while the POWER indicator is blinking.
2. The system assumes the Standby mode when cooling is complete, and the POWER indicator
ceases blinking and changes to orange. Check that the indicator is orange and set the Power
switch to [O].
3. The POWER indicator is extinguished when power is off. Do not forget to close the Slide Lens
Door.
WARNING • Please read this manual, and the separate “Product Safety
Guide” thoroughly before using the equipment. Always ensure that the
equipment is used safely.
NOTE • Except in emergencies, do not turn off unless the POWER indicator is orange as it will
reduce the life of the projector lamp.
• To prevent any troble, turn on/off the projector when the computer or video tape recorder is OFF.
Providing a RS-232C cable is connected, turn on the computer before the projector.
ENGLISH-9
ENGLISH
OPERATIONS
OPERATIONS (continued)
Basic Operation
The basic operations shown in Table 3 is performed from the supplied remote control transmitter or
the projector control panel. Items indicated by (*) may be used from the control panel.
Table 3 . Basic Operation
Item
Description
Select Input Signal (*) : Press the INPUT button.
RGB IN 1 → RGB IN 2 → VIDEO → S-VIDEO (→ RGB IN 1)
Select RGB Input : Press the RGB button.
INPUT
SELECT
VIDEO/S-VIDEO/ → RGB IN 1/RGB IN 2
RGB IN 1 → RGB IN 2 → DIGITAL (→ RGB IN 1)
Select Video Input : Press the VIDEO button.
RGB IN 1/RGB IN 2 ↔ VIDEO/S-VIDEO
VIDEO ↔ S-VIDEO
• The selected signal name is displayed for approximately 3 seconds when the input
signal is changed.
Set/Clear Position Adjustment Mode : Press the POSITION button.
The [
] icon is displayed in the POSITION mode.
POSITION
Image Position Adjustment: Press the
POSITION mode.
,
,
and
buttons in the
RESET (*)
Initialize Each Item : Select an item and press the RESET button.
Initialize Position Adjustment : Press the RESET button and the
POSITION mode. This function is valid only when RGB signal is input.
• Valid only in the MAGNIFY mode with a video signal is input.
• After approximately 10 seconds of inactivity the [ ] icon is extinguished and the
POSITION mode is cleared automatically.
buttons may operate as the mouse control button. Refer to page 4.
•
, ,
and
• Valid except for the VOLUME, LANGUAGE and H PHASE.
• The RESET button may operate as the mouse control button. Refer to page 4.
MAGNIFY
Set MAGNIFY Mode : Press the MAGNIFY
button.
Move Magnified Area : Run the POSITION in the MAGNIFY mode.
Adjust Magnification : Press the MAGNIFY
/
button in MAGNIFY
mode.
Clear MAGNIFY Mode : Press the MAGNIFY
button.
OFF
• The MAGNIFY mode is cleared by running or setting the AUTO, ASPECT, INPUT
SELECT or VIDEO, or by changing the input signal.
Set/Clear FREEZE Mode : Press the FREEZE button. The [II] icon is
displayed, and the image frozen, in the FREEZE mode.
FREEZE
• The FREEZE mode is cleared by running or setting POSITION, VOLUME, MUTE,
Automatic Adjustment, BLANK ON/OFF, or MENU ON/OFF, or by changing the input
signal.
• Do not forget to clear frozen static images.
NOTE • Use the remote control transmitter at a distance of approximately 3m from the sensor on
the front of the projector, and within a range of 30° left-right. Strong light and obstacles will
interfere with operation of the remote control transmitter.
ENGLISH-10
OPERATIONS (continued)
ENGLISH
Items indicated by (*) may be used from the control panel.
Table 3. Basic Operation (continued)
Item
Description
VOLUME
Volume Adjustment : Press the VOLUME
MUTE (*)
Set/Clear Mute Mode : Press the MUTE button. No sound is heard in the
MUTE mode.
AUTO
/
button.
Automatic Adjustment at RGB Input : Press the AUTO button. Horizontal
position(H.POSIT), vertical position (V.POSIT),clock phase (H.PHASE), and
horizontal size(H.SIZE) are automatically adjusted. Use with the window at
maximum size in the application display.
Automatic Adjustment at Video Input : Press the AUTO button. A signal
type appropriate for the input signal is selected automatically. Valid only
when AUTO is set for VIDEO on the menu.
• This operation requires approximately 10 seconds. It may not function correctly with
some input signals.
TIMER
ON/OFF
BLANK
ON/OFF
Timer Start/Stop: Press the TIMER button.
Count-down and display by the minute from the initial value (1~99) set in
TIMER on the Options menu to 0.
• The timer is not displayed in the BLANK MODE or FREEZE MODE.
Set/Clear Blank Mode: Press the BLANK button. No image is displayed in
the Blank mode. The screen color is as set in BLANK on the Image menu.
Menu Display Start/Stop: Press the MENU button.
MENU
• The menu display is terminated automatically after approximately 10 seconds of
ON/OFF (*)
inactivity.
Select Menu Type: Press the MENU SELECT button. Allows the user to
select the normal menu or the single menu. Only the selected item is
displayed on the single menu, and other items are displayed with the
and
buttons as with the normal menu.
MENU
SELECT
• Valid only when the Setup menu is used. Push the MENU SELECT button after
selecting items such as "BRIGHTNESS".
• The MENU SELECT button may operate as the mouse control button. Refer to
page 4.
Normal menu
Single menu
(MENU SELECT)
SETUP
INPUT
BRIGHT
CONTRAST
V POSIT
H POSIT
H PHASE
H SIZE
COLOR BAL R
COLOR BAL B
ASPECT
IMAGE
OPT.
0
-2
100
100
+1
800
0
0
CONTRAST
-2
ENGLISH-11
OPERATIONS (continued)
Setup Menu
SETUP
The following adjustments and settings are possible
when SETUP is selected at the top of the menu. Part
of the Setup menu differs between RGB input and
video input. Select an item with the
and
buttons, and start operation. Use the Single menu to
reduce menu size (see Table 3, MENU SELECT).
Table 4. Setup Menu
Item
INPUT
BRIGHT
CONTRAST
V POSIT
H POSIT
H PHASE
H SIZE
COLOR BAL R
COLOR BAL B
ASPECT
IMAGE
OPT.
SETUP
0
-2
INPUT
IMAGE
OPT.
0
+1
+1
0
0
0
0
BRIGHT
CONTRAST
SHARPNESS
COLOR
TINT
COLOR BAL R
COLOR BAL B
ASPECT
100
100
+1
800
0
0
VIDEO
S-VIDEO
RGB IN 1
RGB IN 2
Description
↔ Light
RGB IN 1
RGB IN 2
VIDEO
S-VIDEO
✔
✔
BRIGHT
Adjustment: Dark
CONTRAST
Adjustment: Weak
↔ Strong
✔
✔
V POSIT
Adjustment: Down
↔ Up
✔
-
H POSIT
Adjustment: Left
↔ Right
✔
-
H PHASE
Adjustment: Left
↔ Right
• Adjust to eliminate flicker.
✔
-
H SIZE
↔ Large
• The image may not be displayed correctly if the horizontal
size is excessive. In such cases, press the RESET button, and
initialize the horizontal size.
✔
-
SHARPNESS
Adjustment: Soft
↔ Clear
-
✔
COLOR
Adjustment: Light
↔ Dark
-
✔
TINT
Adjustment: Red
-
✔
COLOR BAL R
Adjustment: Light
↔ Dark
✔
✔
COLOR BAL B
Adjustment: Light
↔ Dark
✔
✔
✔
-
-
✔
Adjustment: Small
↔ Green
• Valid only when NTSC or NTSC 4.43 signal is received.
Select Image Aspect Ratio : 4:3[
]
↔
16:9[
]
Select Position of Image:
Press the
button while 16:9[
] is selected.
Center →
Down →
Up ( → Center
)
ASPECT
Select Image Aspect Ratio:
4:3[
]
↔
16:9[
]
↔
4:3 small[
Select Position of Image :
Press the
button while 16:9[
] / 4:3 small[
selected.
Center →
Down →
Up ( → Center
)
]
] is
• 4:3 small may not be displayed correctly with some input
signals.
ENGLISH-12
Input Menu
The following functions are available when INPUT is selected on the
menu. Select an item with the
and
buttons, and start or stop
operation with the
and
buttons. The function indicated (**) are
effective on video input mode only, not on RGB input mode, except in
the P.IN P. window on RGB input mode.
SETUP
RGB
VIDEO
AUTO
INPUT
IMAGE
OPT.
fH:38kHz
fV:60Hz
Table 5. Input Menu
Item
RGB
Description
Displays RGB Input Frequency: Displays the horizontal and vertical sync
signal frequencies for RGB input.
• Valid only at RGB input.
VIDEO (**)
AUTO
Select Video Signal Type: Select the signal type with the
and
buttons. Select NTSC, PAL, SECAM, NTSC4.43, M-PAL, or N-PAL as
appropriate for the input signal. The selection of AUTO enables and
executes the function AUTO (Automatic Adjustment at Video Input), except
for the N-PAL input.
• Use this function when the image becomes unstable (eg. the image becomes
irregular, or lacks color) at VIDEO/S-VIDEO input.
• Automatic Adjustment requires approximately 10 seconds. It may not function
correctly with some input signals. Pressing the AUTO button in this case may correct
this problem except for the N-PAL input.
Automatic Adjustment at RGB Input: Select the EXECUTE with the
button. Horizontal position (H.POSIT), vertical position (V.POSIT), clock
phase (H.PHASE), and horizontal size (H.SIZE) are automatically adjusted.
Use with the window at maximum size in the application display.
Automatic Adjustment at Video Input: Select the EXECUTE with the
button. A signal type appropriate for the input signal is selected
automatically when EXECUTE is selected automatically. Valid only when
AUTO is set for VIDEO on the menu.
• This operation requires approximately 10 seconds. It may not function correctly with
some input signals. Pressing the AUTO button in this case may correct this problem.
• This function is the same as for the AUTO function in Basic operation.
ENGLISH-13
ENGLISH
OPERATIONS (continued)
OPERATIONS (continued)
Image Menu
SETUP
The following adjustments and settings are available when IMAGE is
selected on the menu. Select an item with the
and
buttons, and
start operation.
INPUT
IMAGE
OPT.
+1
KEYSTONE
BLANK
MIRROR
START UP
Table 6. Image Menu
Item
KEYSTONE
Description
Keystone Adjustment:
Reduce size of bottom of image
↔ Reduce size of top of image
• When this function is activated, the image may not be displayed correctly with some
input signals.
Select Blank Screen Color: Select color with the
BLANK
MIRROR
START UP
and
buttons.
• The image is cleared when the BLANK mode is set with BLANK ON, or when there
is no signal, and the entire screen is displayed in the selected color.
Operation Start/Stop: Press the
or
button.
Select Mirror Status: Select mirror status with
and
Operation Start/Stop: Press the
or
button.
Setup Initial Screen Display: Select TURN ON with the
Clear Initial Screen Display: Select TURN OFF with the
buttons.
button.
button.
• Note that if TURN OFF is selected the blank screen is displayed in blue when there
is no signal.
ENGLISH-14
Options Menu
SETUP
The following adjustments and settings are available when OPT. is
selected on the menu. Select an item with the
and
buttons, and
start operation.
INPUT
IMAGE
OPT.
128
VOLUME
MENU COLOR
TIMER
LANGUAGE
AUTO OFF
SYNC ON G
WHISPER
Table 7. Options Menu
Item
VOLUME
Description
Volume Adjustment: Reduce VOLUME
↔ Increase VOLUME
MENU COLOR Select Menu Background Color: Select with the
TIMER
LANGUAGE
AUTO OFF
SYNC ON G
and
buttons.
Operation start/stop: Press the
or
button.
Setup initial timer value:
Set 1~99 minutes with the
and buttons.
Operation Start/Stop: Press the
or
button.
Select Menu Display Language: Select with the
and
buttons.
Operation Start/Stop: Press the
or
button.
Set AUTO OFF: Set 1~99 minutes with the
and
buttons. The
system automatically enters the standby mode when a signal is not
received for the set time.
Clear AUTO OFF: Select STOP (0 min.) with the
button. When STOP
is selected the system does not enter the standby mode even if no signal
is received.
Operation Start/Stop: Press the
or
button.
SYNC ON G Valid: Select TURN ON with the
button.
SYNC ON G Invalid: Select TURN OFF with the
button.
• May not be displayed correctly with some input signals when SYNC ON G is
valid. In such cases, remove the signal connector so that no signal is received, set
SYNC ON G to invalid, and reconnect the signal.
ENGLISH-15
ENGLISH
OPERATIONS (continued)
OPERATIONS (continued)
No Signal Menu
The same adjustments and settings are available with the Image and
Options menus when the MENU button is pressed during display of the
“NO INPUT IS DETECTED ON ***” or “SYNC IS OUT OF RANGE
ON ***” message while no signal is received.
Table 8. No Signal Menu
Item
VOLUME
KEYSTONE
BLANK
MIRROR
START UP
MENU COLOR
TIMER
LANGUAGE
AUTO OFF
SYNC ON G
WHISPER
40
+1
Description
↔ Increase VOLUME
• When this function is used, audio input is automatically switched to video. The
audio input can be switched by moving the DISK PAD left and right during the
display of the volume adjustment bar. The volume adjustment bar is displayed by
pressing VOLUME
or VOLUME
button.
Volume Adjustment: Reduce VOLUME
VOLUME
KEYSTONE
BLANK
MIRROR
START UP
Keystone Adjustment: Reduce the size of bottom of image
↔
Reduce the size of top of image
Select Blank Screen Color: Select the color with the
and
buttons.
• When the blank mode is set with BLANK ON, by absence of a signal, or by input
of a non-standard signal, the image is cleared and the complete screen is
displayed in the selected color.
Operation Start/Stop: Press the
or
button.
Select Mirror Status: Select the mirror status with the
and
buttons.
Operation Start/Stop: Press the
or
button.
Setup Initial Screen Display: Select the TURN ON with the
button.
Clear Initial Screen Display: Select the TURN OFF with the
button.
• Note that if TURN OFF is selected the blank screen is displayed in blue when
there is no signal.
MENU COLOR Select Menu Background Color: Select the color with the
and
buttons.
Operation start/stop: Press the
or
button.
TIMER
Setup initial timer value: Set 1~99 minutes with the
and
buttons.
Operation Start/Stop: Press the
or
button.
LANGUAGE
Select Menu Display Language: Select the language with the
and
buttons.
Operation start/stop: Press the
or
button.
Set AUTO OFF: Set 1~99 minutes with the
and
buttons. The
system automatically enters the standby mode when a signal is not
AUTO OFF
received for the set time.
Clear AUTO OFF: Select the STOP (0 min.) with the
button. When the
STOP is selected the system does not enter the standby mode even if no signal is
received.
SYNC ON G
ENGLISH-16
Operation Start/Stop: Press the
or
button.
SYNC ON G Valid: Select the TURN ON with the
button.
SYNC ON G Invalid: Select the TURN OFF with the
button.
• May not be displayed correctly with some input signals when the SYNC ON G is
valid. In such cases, remove the signal connector so that no signal is received, set
the SYNC ON G to invalid, and reconnect the signal.
Lamp
HIGH VOLTAGE
HIGH TEMPERATURE
HIGH PRESSURE
Contact your dealer before replacing the lamp.
For the optional lamp, see the item “Accessories” of P.24.
Before replacing the lamp, switch power OFF, remove the power cord from the power outlet, and
wait approximately 45 minutes until the lamp has cooled. The lamp may explode if handled at high
temperatures.
WARNING • For disposal of used lamp, treat
according to the instruction of community
authorities.
• Since the lamp is made of glass, do not apply shock
to it and do not scratch it.
• Also, do not use old lamp. This could also cause
explosion of the lamp.
• If it is probable that the lamp has exploded (explosive
sound is heard), disconnect the power plug from the
power outlet and ask your dealer to replace lamp. The
lamp is covered by front glass , but, in rare cases, the
reflector and the inside of the projector may be
damaged by scattered broken pieces of glass, and
broken pieces could cause injury when being handled.
• Do not use the projector with the lamp cover removed.
Lamp
Reflector
Front
glasss
Lamp Life
Projector lamps have a finite life. The image will become darker, and hues will become weaker,
after a lamp has been used for a long period of time.
Replace the lamp if the LAMP indicator is red, or the CHANGE THE LAMP message appears
when the projector is switched ON. See Table 9 of P.20 and Table 10 of P.21.
NOTE • The LAMP indicator is also red when the lamp unit reaches high temperature. Before
replacing the lamp, switch power OFF, wait approximately 20 minutes, and switch power ON again.
If the LAMP indicator is still red, replace the lamp.
ENGLISH-17
ENGLISH
MAINTENANCE
MAINTENANCE (continued)
Replacing the Lamp
1. Switch the projector OFF, remove the power cord from the
power outlet, and wait at least 45 minutes for the unit to cool.
2. Prepare a new lamp.
3. Check that the projector has cooled sufficiently, and gently
turn it upside down.
4. Loosen the two screws as shown in the diagram, and remove
the lamp cover.
5. Loosen the three screws, and gently remove the lamp while
holding the grips. Touching the inside of the lamp case may
result in uneven coloring.
6. Install the new lamp and tighten the three screws firmly.
Also steadily push the opposite side of the screwed lamp into
the unit.
7. Replace the lamp cover in position and tighten the two
screws firmly.
8. Gently turn the projector right-side up.
CAUTION • Ensure that screws are tightened
properly. Screws not tightened fully may result
in injury or accidents.
• Do not use the projector with the lamp cover
removed.
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp. When the lamp has been replaced after the LAMP
indicator is red, or the CHANGE THE LAMP message is displayed, complete the following
operation within 10 minutes of switching power ON. The power will be turned off automatically in
over 10 minutes.
1. Switch power ON, and press the TIMER button on the remote control transmitter, or the RESET
button on the control panel, for approximately three seconds. The ‘LAMP xxxx hr’ message
will appear on the lamp timer on the bottom of the screen.
2. Press the MENU button on the remote control transmitter, or the RESET button on the control
panel, while the lamp timer is displayed. The ‘LAMP xxxx → 0 ■ CANCEL’ message will
then appear.
3. Press the
and select 0, and wait until the timer display is cleared.
NOTE • Do not reset the lamp timer without replacing the lamp. Reset the lamp timer always
when replacing the lamp. The message functions will not operate properly if the lamp timer is not
reset correctly.
ENGLISH-18
Air Filter Maintenance
The air filter should be cleaned as described below at intervals of approximately 100 hours.
1. Switch the projector power supply OFF, and remove the power cord from the power outlet.
2. Clean the air filter with a vacuum cleaner.
CAUTION • Switch power OFF and remove the power cord from the power
outlet before beginning maintenance work. Please read the separate “Product
Safety Guide” thoroughly to ensure that maintenance is performed correctly.
• Replace the air filter if contamination cannot be removed, or if it is damaged.
Contact your dealer in such case. For the optional air filter, see the item
“Accessories” of P.24.
• Do not use the equipment with the air filter removed.
• When the air filter is clogged with dust etc. the power supply is switched OFF
automatically to prevent the temperature rising inside the projector.
Other Maintenance
Maintenance Inside the Equipment
For safety reasons, ensure that the equipment is cleaned and checked by the dealer once every two
years. Maintaining the equipment by yourself is dangerous.
Cleaning the Lens
Gently wipe the lens with lens cleaning paper. Do not touch the lens with your hands.
Cleaning the Cabinet and Remote control transmitter
Gently wipe with a soft cloth. If dirt and stains etc. are not easily removed, use a soft cloth
dampened with water, or water and a neutral detergent, and wipe dry with a soft, dry cloth.
CAUTION • Switch power OFF and remove the power cord from the power
outlet before beginning maintenance work. Please read the separate “Product
Safety Guide” thoroughly to ensure that maintenance is performed correctly.
• Do not use detergents or chemicals other than those noted above (e.g. benzene
or thinners).
• Do not use cleaning sprays.
• Do not rub with hard materials, or tap the equipment.
ENGLISH-19
ENGLISH
MAINTENANCE (continued)
TROUBLESHOOTING
Service Infomation
For product infomation, product assistance, service infomation, or to order accessories, please call:
In U.S. or Canada : 1-800-328-1371
In other locations, contact your local 3M sales office.
OSD Message
The messages as described below may appear on the screen at power ON. Take the appropriate
measures when such messages appears.
Table 9. OSD Messages
Message
Contents
The message shown at left appears after the lamp has
been used for more than 1700 hours.
CHANGE THE LAMP
The lamp is approaching the end of its life.
AFTER REPLACING LAMP,
Power is switched OFF automatically when the lamp
RESET THE LAMP TIME.
*1) reaches the end of its life. Prepare a new lamp for
installation.
Always reset the lamp timer after replacing the lamp.
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIME.
THE POWER WILL TURN OFF
AFTER ** hr.
*1)
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIME.
THE POWER WILL
TURN OFF
AFTER 0 hr.
NO INPUT IS DETECTED
ON ***
SYNC IS OUT OF RANGE
ON ***
CHECK THE AIR FLOW
The lamp will reach the end of its life in ** hours.
Power will be switched OFF automatically in ** hours.
Replace the lamp as shown in P.17~18 “Lamp”.
Always reset the lamp timer after replacing the lamp.
The lamp has reached the end of its life. Power will be
switched OFF in a few minutes.
Switch power OFF immediately and replace the lamp as
shown in P.17~18 “Lamp”.
Always reset the lamp timer after replacing the lamp.
No input signal found.
Check signal input connections and signal sources.
The horizontal or vertical frequency of the input signal is
not within the specified range.
Check the specifications of the equipment and the signal
source.
The internal temperature has risen.
Switch power OFF, and wait 20 minutes until the
equipment cools.
Check the following and Switch power ON again.
• Are the ventilation openings blocked?
• Is the air filter dirty?
• Is the ambient temperature in excess of 35°C?
NOTE *1) This message is cleared automatically after approximately 3 minutes, and appears
every time power is switched ON.
ENGLISH-20
Indicators Message
The POWER indicator, LAMP indicator, and TEMP indicator are lit and blank as follows. Take the
appropriate measures.
Table 10. Indicators Message
POWER
LAMP
TEMP
indicator indicator indicator
Contents
Lights
orange
Turns off Turns off The Standby mode has been set.
Blinks
green
Turns off Turns off Warming up. Please wait.
Lights
green
Turns off Turns off ON. Normal operation possible.
Blinks
orange
Turns off Turns off Cooling. Please wait.
Lights red
Lights red
Lights
red
Lamp is not lit.
The interior of the equipment may be too hot. Switch
power OFF, wait 20 minutes until the equipment cools,
Turns off and check whether the ventilation openings are blocked,
whether the air filter is dirty, or whether the ambient
temperature exceeds 35 °C. And switch power ON
again. Replace the lamp if the same problem occurs.
Blinks
red
Lamp or lamp cover is not found, or hasn’t been fitted in
correctly.
Switch power OFF, and wait for 45 minutes until the
Turns off
equipment cools. Check fitting of the lamp and lamp
cover, and switch power ON again. Contact your dealer if
the same problem occurs again.
Lights red Turns off
Blinks
red
The cooling fan is not operating.
Switch power OFF, and wait for 20 minutes until the
equipment cools. Check for foreign matters in the fan,
and switch power ON again. Contact your dealer if the
same problem occurs again.
The interior of the equipment is too hot. *2)
Switch power OFF, and wait for 20 minutes until the
equipment cools. Check whether the ventilation openings
Lights red Turns off Lights red are blocked, whether the air filter is dirty, or whether the
ambient temperature exceeds 35 °C. Then switch power
ON again. Contact your dealer if the same problem
occurs again.
NOTE *2) When the internal temperature becomes excessive power is switched OFF
automatically for safety reasons, and the indicator is extinguished. Set the power switch to [O] and
wait for 20 minutes until the equipment has cooled sufficiently.
ENGLISH-21
ENGLISH
TROUBLESHOOTING (continued)
TROUBLESHOOTING (continued)
Symptom
Before requesting repair, check in accordance with the following chart. If the situation cannot be
corrected, then contact your dealer.
Table 11. Symptom
Symptom
The power is not
turned on.
Possible cause
Turn on the main power switch.
The power cord is
disconnected.
Plug the power cord into an AC
power outlet.
The input is not correctly set.
Use the projector or remote control
transmitter to set.
10
No signal input.
Connect correctly.
7,8
The projector is not correctly
connected.
Connect correctly.
7,8
Video is present but
The volume is set to minimum.
no audio.
11,15
11
Press the MUTE
The projector is not correctly
connected.
Connect correctly.
7,8
Select BRIGHT with the MENU
button and the press the
button.
12
The lens cap is still attached.
Colors are pale and Color density and color
color matching is
matching are not correctly
poor.
adjusted.
ENGLISH-22
Press VOLUME
on the remote
control or display the menu screen
and adjust the volume.
8,9
Mute is turned on.
Audio is present but The brightness is set to
minimum.
no video.
Images are blurred.
Page
The main power switch is not
turned on.
No video or audio.
Images are dark.
Remedy
button.
Remove the lens cap.
9
Adjust the video.
12
Brightness and contrast are not
correctly adjusted.
Adjust the video.
12
The lamp is nearing the end of
its service life.
Replace with a new lamp.
17
Focus or H PHASE is out of
adjustment.
Adjust the focus or H PHASE.
9,12
ENGLISH
SPECIFICATIONS
Table 12. Specifications
Item
Product name
Liquid
crystal
panel
Panel size
Specification
Liquid crystal projector
2.3 cm (0.9 type)
Drive system TFT active matrix
Pixels
480,000 pixels (800 horizontal x 600 vertical)
Lens
Zoom lens F=1.7 ~ 2.0 f=37.5 ~ 45.1 mm
Lamp
160 W UHB
Speaker
1.0 W + 1.0W (Stereo)
Power supply
AC100 ~ 120V, 2.8A / AC220 ~ 240V, 1.2A
Power consumption
250W
Temperature range
0 ~ 35°C (Operating)
Size
298 (W) x 94.6 (H) x 228 (D) mm
Weight (mass)
3.25 kg
RGB signal
input
RGB IN 1/2
AUDIO IN
1/2
VIDEO IN
Video: Analog 0.7Vp-p, 75Ω terminator (positive)
H/V. sync.: TTL level (positive/negative)
Composite sync.: TTL level
D-sub 15-pin shrink jack
200mVrms, 50 kΩ (max. 3.0Vp-p)
Stereo mini jack
1.0Vp-p, 75Ω terminator
RCA jack
Brightness signal: 1.0Vp-p, 75Ω terminator
Video
S-VIDEO IN Color signal: 0.286Vp-p (burst signal), 75Ω terminator
signal input
Mini DIN 4-pin jack
AUDIO IN
R/L
Signal
output
Control
functions
200mVrms, 50 kΩ (max. 3.0Vp-p)
RCA jack
Video: Analog 0.7Vp-p, 75Ω output impedance (positive)
H/V. sync.: TTL level (positive/negative)
RGB OUT
Composite sync.: TTL level
D-sub 15-pin shrink jack
200mVrms, output impedance 1 kΩ (max. 3.0Vp-p)
AUDIO OUT
Stereo mini jack
CONTROL
D-sub 15-pin shrink plug
USB
USB jack (B type)
NOTE • This specifications are subject to change without notice.
ENGLISH-23
ACCESSORIES
Acccessories..................................................................................Part Number
UHB lamp, 160W ...........................................................................78-6969-9260-7
Air Filter..........................................................................................78-8118-8896-1
Power cable (US) ..........................................................................DY-0205-1356-9
Power cable (UK) ..........................................................................DY-0205-1355-1
Power cable (Europe) ...................................................................DY-0205-1354-4
S-Video cable.................................................................................78-8118-3238-1
RGB cable......................................................................................78-8118-8708-8
Video/audio cable...........................................................................78-8118-3234-0
Mouse cable (PS/2)........................................................................78-8118-8105-7
Remote control transmitter.............................................................78-8118-8652-8
Handle............................................................................................78-8118-8673-4
Not Included with Basic Packet....................................................Part Number
Ceiling mount .................................................................................78-6969-9261-5
Adjustable height suspension ........................................................78-6969-8312-7
Shipping case.................................................................................78-6969-9259-9
Soft carry case ...............................................................................78-6969-9203-7
Deluxe leather carry case ..............................................................78-6969-9144-3
Stereo mini jack cable ....................................................................78-8118-8290-7
Mouse cable (ADB) ........................................................................78-8118-8106-5
Mouse cable (Serial) ......................................................................78-8118-8107-3
Mouse cable (USB) ........................................................................78-8118-8186-7
RS-232C control cable ...................................................................78-8118-3312-4
Mac adapter ...................................................................................78-8118-3308-2
How to Order
Please order these parts through your dealer, or contact 3M Customer Service at the
following number :
In U.S. or Canada : 1-800-328-1371
In other locations,contact your local 3M sales office.
ENGLISH-24
TECHNICAL
228
Dimension Diagram
AC N
298
76
94.6
54
Unit : mm
76.5
Signal Connector Pin Assignment
1. D-sub 15-pin Shrink Connector (RGB IN 1/RGB IN 2/RGB OUT)
Pin No
1
2
3
4
5
6
7
8
Signal
Video input Red
Video input Green
Video input Blue
Ground
Ground Red
Ground Green
Ground Blue
Pin No
Signal
9
10
11
-
12
13
14
Ground
RGB IN 1: SDA(DDC)
RGB IN 2: RGB OUT: H. sync./ Composite sync.
Vertical sync
Pin No
15
Signal
RGB IN 1: SCL(DDC)
RGB IN 2: RGB OUT: -
# " !
' & % $
# " ! 2. Mini Din 4-pin Connector (S-VIDEO)
Signal
1
Color:0.286Vp-p (NTSC, burst signal),75Ω terminator
0.3Vp-p (PAL/SECAM, burst signal),75Ω terminator
2
Brightness:1.0Vp-p, 75Ω terminator
3
Ground
4
Ground
TECHNICAL
Pin No
TECHNICAL - 25
TECHNICAL (continued)
Example of computer signal
Resolution
H×V
fH (kHz)
fV (Hz)
Rating
720 × 400
37.9
85.0
640 × 480
31.5
59.9
640 × 480
35.0
66.7
640 × 480
37.9
72.8
640 × 480
37.5
75.0
640 × 480
43.3
85.0
800 × 600
35.2
56.3
800 × 600
37.9
800 × 600
800 × 600
Signal mode
Display
mode
VESA
TEXT
Zoom in
VESA
VGA (60Hz)
Zoom in
Mac13"mode
Zoom in
VESA
VGA (72Hz)
Zoom in
VESA
VGA (75Hz)
Zoom in
VESA
VGA (85Hz)
Zoom in
VESA
SVGA (56Hz)
60.3
VESA
SVGA (60Hz)
48.1
72.2
VESA
SVGA (72Hz)
46.9
75.0
VESA
SVGA (75Hz)
800 × 600
53.7
85.1
VESA
SVGA (85Hz)
832 × 624
49.7
74.5
Mac16"mode
Zoom out
1024 × 768
48.4
60.0
VESA
XGA (60Hz)
Zoom out
1024 × 768
56.5
70.1
VESA
XGA (70Hz)
Zoom out
1024 × 768
60.0
75.0
VESA
XGA (75Hz)
Zoom out
1024 × 768
68.7
85.0
VESA
XGA (85Hz)
Zoom out
1280 × 1024
64.0
60.0
VESA
SXGA (60Hz)
Zoom out *
NOTE • Some computers may have multiple display screen modes. Use of some of these modes
will not be possible with this projector.
• Be sure to check jack type, signal level, timing and resolution before connecting this projector to a
computer.
• Depending on the input signal, full-size display may not be possible in some cases. Refer to the
number of display pixels above.
* It becomes the simple display of thinning out data.
TECHNICAL - 26
TECHNICAL (continued)
Initial set signals
The following signals are used for the initial settings.
The signal timing of some computer models may be different. In such case, refer to adjust the
V.POSIT and H.POSIT of the menu.
Back porch b
Front porch d
Display interval c
Back porch b
Front porch d
Display interval c
DATA
DATA
HSYNC
VSYNC
Sync a
Computer /
Signal
Sync a
Horizontal signal timing (µs)
TEXT
a
2.0
b
3.0
c
20.3
d
1.0
VGA (60Hz)
3.8
1.9
25.4
Mac 13"mode
2.1
3.2
VGA (72Hz)
1.3
VGA (75Hz)
Computer /
Signal
Vertical signal timimg (lines)
a
3
b
42
c
400
d
1
0.6
VGA (60Hz)
2
33
480
10
21.2
2.1
Mac 13"mode
3
39
480
3
3.8
20.3
1.0
VGA (72Hz)
3
28
480
9
2.0
3.8
20.3
0.5
VGA (75Hz)
3
16
480
1
VGA (85Hz)
1.6
2.2
17.8
1.6
VGA (85Hz)
3
25
480
1
SVGA (56Hz)
2.0
3.6
22.2
0.7
SVGA (56Hz)
2
22
600
1
SVGA (60Hz)
3.2
2.2
20.0
1.0
SVGA (60Hz)
4
23
600
1
SVGA (72Hz)
2.4
1.3
16.0
1.1
SVGA (72Hz)
6
23
600
37
SVGA (75Hz)
1.6
3.2
16.2
0.3
SVGA (75Hz)
3
21
600
1
SVGA (85Hz)
1.1
2.7
14.2
0.6
SVGA (85Hz)
3
27
600
1
Mac 16"mode
1.1
3.9
14.5
0.6
Mac 16"mode
3
39
624
1
XGA (60Hz)
2.1
2.5
15.8
0.4
XGA (60Hz)
6
29
768
3
XGA (70Hz)
1.8
1.9
13.7
0.3
XGA (70Hz)
6
29
768
3
XGA (75Hz)
1.2
2.2
13.0
0.2
XGA (75Hz)
3
28
768
1
XGA (85Hz)
1.0
2.2
10.8
0.5
XGA (85Hz)
3
36
768
1
1280×1024(60Hz)
1.0
2.3
11.9
0.4
1280×1024(60Hz)
3
38
1024
1
TECHNICAL
TEXT
TECHNICAL - 27
TECHNICAL (continued)
Connection to the Mouse Control
1. PS/2, ADB or Serial Mouse
(1) Turn off the projector and computer, and connect the two units with the appropriate cable. For
PS/2 mouse control (for IBM and compatible), use the enclosed mouse cable. For others, consult
your dealer.
(2) Disconnect the USB cable from the projector if it is connected. Then turn on the projector.
(3) Turn on the computer.
(4) Start the mouse function. If the mouse has not been started, reboot the computer (soft reboot or
reboot buttons). Refer to the descriptions of “DISC PAD” and “MOUSE/RIGHT button” of page 4.
2. USB Mouse
(1) Connect the projector and computer with a suitable commercially available USB cable. Consult
your dealer to get the cable, if you need.
(2) Start the mouse function. Refer to the descriptions of “DISC PAD” and “MOUSE/RIGHT
button” of page 4.
NOTE • Before connecting, read the instruction manuals of the devices to be connected.
• In the case of notebook type computers with an internal pointing device, the mouse control
function will not work unless the internal pointing device is disabled. In such case, disable the
internal pointing device and change the BIOS setting to select an external mouse before the
operations described in (1) to (4) above.
Also, some computers may not have a utility program to operate a mouse.
Refer to the computer hardware manual for detail.
PS/2 Mouse
Projector
CONTROL Terminal
CLK
DATA
D-sub 15-pin shrink jack
$
! " #
% & ' ! " #
SEL0
RTS
+5V
GND
TECHNICAL - 28
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Computer
1
2
3
4
5
6
DATA
GND
+5V
CLK
Mouse jack
Mini DIN 6-pin
6
5
3
4
2
1
TECHNICAL (continued)
ADB Mouse
Projector
CONTROL Terminal
DATA
D-sub 15-pin shrink jack
$
! " #
% & ' ! " #
RTS
+5V
GND
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Computer
1 ADB
2 (POWER ON)
3 +5V
4 GND
Mouse jack
Mini DIN 4-pin
3
4
1
2
Serial Mouse
Projector
CONTROL Terminal
D-sub 15-pin shrink jack
$
! " #
% & ' ! " #
SEL0
RTS
GND
TD
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
1
2
3
4
5
6
7
8
9
Computer
CD
RD
TD
DTR
GND
DSR
RTS
CTS
RI
Mouse jack
D-sub 9-pin
1
2
6
3
7
5
4
8
9
USB Mouse
2
3
1
4
Computer
Projector
+5V 1
1
+5V
—DATA 2
2 —DATA
+DATA 3
3
GND 4
USB jack
(A type)
+DATA
4 GND
1
2
3
4
USB cable
TECHNICAL - 29
TECHNICAL
USB jack
(B type)
TECHNICAL (continued)
RS-232C communication
(1) Turn off the projector and computer power supplies and connect with the RS-232C cable.
(2) Turn on the computer power supply and after the computer has started up, turn on the projector
power supply.
Projector
Control jack
D-sub 15-pin shrink jack
# " !
' & % $
# " ! Computer
1
2
3
4
5
SELO 6
RTS 7
8
9
GND 10
11
12
RD 13
TD 14
15
1
2
3
4
5
6
7
8
9
CD
RD
TD
DTR
GND
DSR
RTS
DTS
RI
RS-232C jack
D-sub 9-pin
2
1
6
3
7
Communications setting
19200bps, 8N1
1 Protocol
Consist of header (7 bytes) + command data (6 bytes).
2 Header
BE + EF + 03 + 06 + 00 + CRC_low + CRC_high
CRC_low : Lower byte of CRC flag for command data.
CRC_high : Upper byte of CRC flag for command data.
3 Command data
Command data chart
byte_0
byte_1
byte_2
Action
low
byte_3
Type
high
low
byte_4
byte_5
Setting code
high
low
high
Action (byte_0 - 1)
Action
Classification
Content
1
SET
Change setting to desired value.
2
GET
Read projector internal setup value.
4
INCREMENT
Increment setup value by 1.
5
DECREMENT
Decrement setup value by 1.
6
EXECUTE
Run a command.
TECHNICAL - 30
4
8
5
9
TECHNICAL (continued)
Requesting projector status (Get command)
(1) Send the request code Header + Command data (‘02H’+‘00H’+ type (2 bytes) +‘00H’+‘00H’)
from the computer to the projector.
(2) The projector returns the response code ‘1DH’+ data (2 bytes) to the computer.
Changing the projector settings (Set command)
(1) Send the setting code Header + Command data (‘01H’+‘00H’+ type (2 bytes) + setting code (2
bytes)) from the computer to the projector.
(2) The projector changes the setting based on the above setting code.
(3) The projector returns the response code ‘06H’ to the computer.
Using the projector default settings (Reset Command)
(1) The computer sends the default setting code Header + Command data (‘06H’+‘00H’+ type (2
bytes) +‘00H’+‘00H’) to the projector.
(2) The projector changes the specified setting to the default value.
(3) The projector returns the response code ‘06H’ to the computer.
Increasing the projector setting value (Increment command)
(1) The computer sends the increment code Header + Command data (‘04H’+‘00H’+ type (2 bytes)
+‘00H’+‘00H’) to the projector.
(2) The projector in creases the setting value on the above setting code.
(3) The projector returns the response code ‘06H’ to the computer.
Decreasing the projector setting value (Decrement command)
(1) The computer sends the decrement code Header + Command data (‘05H’+‘00H’+ type (2 bytes)
+‘00H’ + ‘00H’) to the projector.
(2) The projector decreases the setting value on the above setting code.
(3) The projector returns the response code ‘06H’ to the computer.
When a command sent by the projector cannot be understood by the computer
When the command sent by the projector cannot be understood, the error command ‘15H’ is
returned by the computer. Some times, the projector ignores RS-232C commands during other
works. If the error command ‘15H’ is returned, please send the same command again.
When data sent by the projector cannot be practice
NOTE • Operation cannot be guaranteed when the projector receives an undefined command or
data.
• Provide an interval of at least 40ms between the response code and any other code.
• The projector outputs test data when the power supply is switched ON, and when the lamp is lit.
Ignore this data.
• Commands are not accepted during warm-up.
TECHNICAL - 31
TECHNICAL
When the command sent by the projector cannot be practiced, the the error code ‘1cH’ +‘xxxxH’ is
returned.
When the data length is greater than indicated by the data length code, the projector will ignore the
excess data code.
Conversely, when the data length is shorter than indicated by the data length code, an error code
will be returned to the projector.
TECHNICAL (continued)
Command data chart
Names
Blank Color
Operation type
Set
Type
Setting code
Red
BE EF
03
06 00
3B D3
01 00
00 30
00 00
Orange
BE EF
03
06 00
AB D2
01 00
00 30
01 00
Green
BE EF
03
06 00
5B D2
01 00
00 30
02 00
Blue
BE EF
03
06 00
CB D3
01 00
00 30
03 00
Purple
BE EF
03
06 00
FB D1
01 00
00 30
04 00
White
BE EF
03
06 00
6B D0
01 00
00 30
05 00
Black
BE EF
03
06 00
9B D0
01 00
00 30
06 00
BE EF
03
06 00
08 D3
02 00
00 30
00 00
Normal
BE EF
03
06 00
C7 D2
01 00
01 30
00 00
H Inverse
BE EF
03
06 00
57 D3
01 00
01 30
01 00
V lnverse
BE EF
03
06 00
A7 D3
01 00
01 30
02 00
H&V Inverse
BE EF
03
06 00
37 D2
01 00
01 30
03 00
BE EF
03
06 00
F4 D2
02 00
01 30
00 00
Normal
BE EF
03
06 00
83 D2
01 00
02 30
00 00
Freeze
BE EF
03
06 00
13 D3
01 00
02 30
01 00
BE EF
03
06 00
B0 D2
02 00
02 30
00 00
Red
BE EF
03
06 00
7F D3
01 00
03 30
00 00
Orange
BE EF
03
06 00
EF D2
01 00
03 30
01 00
Green
BE EF
03
06 00
1F D2
01 00
03 30
02 00
Blub
BE EF
03
06 00
8F D3
01 00
03 30
03 00
Purple
BE EF
03
06 00
BF D1
01 00
03 30
04 00
Transparent
BE EF
03
06 00
2F D0
01 00
03 30
05 00
Gray
BE EF
03
06 00
DF D0
01 00
03 30
06 00
Get
BE EF
03
06 00
4C D3
02 00
03 30
00 00
Turn ON
BE EF
03
06 00
0B D2
01 00
04 30
00 00
Turn OFF
BE EF
03
06 00
9B D3
01 00
04 30
01 00
Get
BE EF
03
06 00
38 D2
02 00
04 30
00 00
English
BE EF
03
06 00
F7 D3
01 00
05 30
00 00
Français
BE EF
03
06 00
67 D2
01 00
05 30
01 00
Deutsch
BE EF
03
06 00
97 D2
01 00
05 30
02 00
Español
BE EF
03
06 00
07 D3
01 00
05 30
03 00
Italiano
BE EF
03
06 00
37 D1
01 00
05 30
04 00
Norsk
BE EF
03
06 00
A7 D0
01 00
05 30
05 00
Nederlands
BE EF
03
06 00
57 D0
01 00
05 30
06 00
Português
BE EF
03
06 00
C7 D1
01 00
05 30
07 00
Japanese
BE EF
03
06 00
37 D4
01 00
05 30
08 00
Get
BE EF
03
06 00
C4 D3
02 00
05 30
00 00
Get
Mirror
Set
Get
Freeze
Set
Get
Menu Color
Startup
Language
Set
Set
Set
TECHNICAL - 32
Command data
Header
CRC
Action
TECHNICAL (continued)
Command data chart
Operation type
Command data
Header
Type
Setting code
Get
BE EF
03
06 00
7C D2
02 00
07 30
00 00
Increment
BE EF
03
06 00
1A D2
04 00
07 30
00 00
Decrement
BE EF
03
06 00
CB D3
05 00
07 30
00 00
Get
BE EF
03
06 00
08 86
02 00
10 31
00 00
Increment
BE EF
03
06 00
CE 86
04 00
10 31
00 00
Decrement
BE EF
03
06 00
BF 87
05 00
10 31
00 00
Get
BE EF
03
06 00
08 86
02 00
10 31
00 00
Increment
BE EF
03
06 00
6E 86
04 00
10 31
00 00
Decrement
BE EF
03
06 00
BF 87
05 00
10 31
00 00
Brightness Reset
Execute
BE EF
03
06 00
58 D3
06 00
00 70
00 00
Contrast Reset
Execute
BE EF
03
06 00
A4 D2
06 00
01 70
00 00
V.Position Reset
Execute
BE EF
03
06 00
E0 D2
06 00
02 70
00 00
H.Position Reset
Execute
BE EF
03
06 00
IC D3
06 00
03 70
00 00
H.Size Reset
Execute
BE EF
03
06 00
68 D2
06 00
04 70
00 00
Color Balance R Reset
Execute
BE EF
03
06 00
94 D3
06 00
05 70
00 00
Color Balance B Reset
Execute
BE EF
03
06 00
D0 D3
06 00
06 70
00 00
Aspect Reset
Execute
BE EF
03
06 00
2C D2
06 00
07 70
00 00
Video Format Reset
Execute
BE EF
03
06 00
38 D1
06 00
08 70
00 00
Sharpness Reset
Execute
BE EF
03
06 00
C4 D0
06 00
09 70
00 00
Color Reset
Execute
BE EF
03
06 00
80 D0
06 00
0A 70
00 00
Tint Reset
Execute
BE EF
03
06 00
7C D1
06 00
0B 70
00 00
Keystone Reset
Execute
BE EF
03
06 00
08 D0
06 00
0C 70
00 00
Mirror Reset
Execute
BE EF
03
06 00
F4 D1
06 00
0D 70
00 00
Blank Color Reset
Execute
BE EF
03
06 00
B0 D1
06 00
0E 70
00 00
Startup Reset
Execute
BE EF
03
06 00
4C D0
06 00
0F 70
00 00
Auto
Execute
BE EF
03
06 00
91 D0
06 00
0A 20
00 00
off
BE EF
03
06 00
FB D8
01 00
20 30
00 00
on
BE EF
03
06 00
6B D9
01 00
20 30
01 00
BE EF
03
06 00
C8 D8
02 00
20 30
00 00
off
BE EF
03
06 00
07 D9
01 00
21 30
00 00
on
BE EF
03
06 00
97 D8
01 00
21 30
01 00
BE EF
03
06 00
34 D9
02 00
21 30
00 00
BE EF
03
06 00
D9 D8
02 00
20 60
00 00
Magnify
Timer
Auto off
Blank on/off
Set
Get
Timer on/off
Set
Get
Error Status
Get
(Example of Return)
00 00
01 00
(Normal) (Cover-error)
04 00
(Temp-error)
CRC
Action
02 00
(Fan-error)
05 00
(Air flow-error)
03 00
(Lamp-error)
06 00
(Lamp-Time-over)
TECHNICAL - 33
TECHNICAL
Names
TECHNICAL (continued)
Command data chart
Names
Power
Operation type
Type
Setting code
OFF
BE EF
03
06 00
2A D3
01 00
00 60
00 00
ON
BE EF
03
06 00
BA D2
01 00
00 60
01 00
BE EF
03
06 00
19 D3
02 00
00 60
00 00
RGB1
BE EF
03
06 00
FE D2
01 00
00 20
00 00
RGB2
BE EF
03
06 00
3E D0
01 00
00 20
04 00
Video
BE EF
03
06 00
6E D3
01 00
00 20
01 00
SVideo
BE EF
03
06 00
9E D3
01 00
00 20
02 00
Get
BE EF
03
06 00
CD D2
02 00
00 20
00 00
Get
BE EF
03
06 00
31 D3
02 00
01 20
00 00
Increment
BE EF
03
06 00
57 D3
04 00
01 20
00 00
Decrement
BE EF
03
06 00
86 D2
05 00
01 20
00 00
Normal
BE EF
03
06 00
46 D3
01 00
02 20
00 00
Mute
BE EF
03
06 00
D6 D2
01 00
02 20
01 00
Get
BE EF
03
06 00
75 D3
02 00
02 20
00 00
Get
BE EF
03
06 00
89 D2
02 00
03 20
00 00
Increment
BE EF
03
06 00
EF D2
04 00
03 20
00 00
Decrement
BE EF
03
06 00
3E D3
05 00
03 20
00 00
Get
BE EF
03
06 00
FD D3
02 00
04 20
00 00
Increment
BE EF
03
06 00
9B D3
04 00
04 20
00 00
Decrement
BE EF
03
06 00
4A D2
05 00
04 20
00 00
Get
BE EF
03
06 00
01 D2
02 00
05 20
00 00
Increment
BE EF
03
06 00
67 D2
04 00
05 20
00 00
Decrement
BE EF
03
06 00
B6 D3
05 00
05 20
00 00
Get
BE EF
03
06 00
45 D2
02 00
06 20
00 00
Increment
BE EF
03
06 00
23 D2
04 00
06 20
00 00
Decrement
BE EF
03
06 00
F2 D3
05 00
06 20
00 00
Get
BE EF
03
06 00
B9 D3
02 00
07 20
00 00
Increment
BE EF
03
06 00
DF D3
04 00
07 20
00 00
Decrement
BE EF
03
06 00
0E D2
05 00
07 20
00 00
4:3
BE EF
03
06 00
9E D0
01 00
08 20
00 00
16:9
BE EF
03
06 00
0E D1
01 00
08 20
01 00
Small
BE EF
03
06 00
FE D1
01 00
08 20
02 00
BE EF
03
06 00
AD D0
02 00
08 20
00 00
Default
BE EF
03
06 00
62 D1
01 00
09 20
00 00
Bottom
BE EF
03
06 00
F2 D0
01 00
09 20
01 00
Top
BE EF
03
06 00
02 D0
01 00
09 20
02 00
BE EF
03
06 00
51 D1
02 00
09 20
00 00
Set
Get
Input Source
Set
Volume
Mute
Set
Brightness
Contrast
Color
Balance R
Color
Balance B
Keystone
Set
Aspect
Get
Display
Position at
16 : 9 or Small
Command data
Header
Set
Get
TECHNICAL - 34
CRC
Action
TECHNICAL (continued)
Command data chart
Operation type
V.Position
H.Position
H.Size
H.Phase
Sharpness
Color
Tint
Set
Video Format
Command data
Header
CRC
Action
Type
Setting code
Get
BE EF
03
06 00
0D 83
02 00
00 21
00 00
Increment
BE EF
03
06 00
6B 83
04 00
00 21
00 00
Decrement
BE EF
03
06 00
BA 82
05 00
00 21
00 00
Get
BE EF
03
06 00
F1 82
02 00
01 21
00 00
Increment
BE EF
03
06 00
97 82
04 00
01 21
00 00
Decrement
BE EF
03
06 00
46 83
05 00
01 21
00 00
Get
BE EF
03
06 00
B5 82
02 00
02 21
00 00
Increment
BE EF
03
06 00
D3 82
04 00
02 21
00 00
Decrement
BE EF
03
06 00
02 83
05 00
02 21
00 00
Get
BE EF
03
06 00
49 83
02 00
03 21
00 00
Increment
BE EF
03
06 00
2F 83
04 00
03 21
00 00
Decrement
BE EF
03
06 00
FE 82
05 00
03 21
00 00
Get
BE EF
03
06 00
F1 72
02 00
01 22
00 00
Increment
BE EF
03
06 00
97 72
04 00
01 22
00 00
Decrement
BE EF
03
06 00
46 73
05 00
01 22
00 00
Get
BE EF
03
06 00
B5 72
02 00
02 22
00 00
Increment
BE EF
03
06 00
D3 72
04 00
02 22
00 00
Decrement
BE EF
03
06 00
02 73
05 00
02 22
00 00
Get
BE EF
03
06 00
49 73
02 00
03 22
00 00
Increment
BE EF
03
06 00
2F 73
04 00
03 22
00 00
Decrement
BE EF
03
06 00
FE 72
05 00
03 22
00 00
Auto
BE EF
03
06 00
9E 75
01 00
00 22
0A 00
NTSC
BE EF
03
06 00
FE 71
01 00
00 22
04 00
PAL
BE EF
03
06 00
6E 70
01 00
00 22
05 00
SECAM
BE EF
03
06 00
6E 75
01 00
00 22
09 00
NTSC 4.43
BE EF
03
06 00
5E 72
01 00
00 22
02 00
M-PAL
BE EF
03
06 00
FE 74
01 00
00 22
08 00
N-PAL
BE EF
03
06 00
0E 71
01 00
00 22
07 00
BE EF
03
06 00
0D 73
02 00
00 22
00 00
Get
TECHNICAL
Names
TECHNICAL - 35
Intended Use
Before operating this machine, please read this entire manual thoroughly. The 3M™ Multimedia Projectors are
designed, built, and tested for use indoors, using 3M lamps, 3M ceiling mount hardware, and nominal local
voltages.
The use of other replacement lamps, outdoor operation, or different voltages has not been tested and could
damage the projector peripheral equipment and/or create a potentially unsafe operating condition.
3M Multimedia projectors and Wall Display Systems are designed to operate in a normal office environment.
• 16° to 29°C (60° to 85° F)
• 10- 80 %RH (without condensation)
• 0- 1828 m (0-6000 feet) above sea level
The ambient operating environment should be free of airborne smoke, grease, oil and other contaminates that
can affect the operation or performance of the projector.
Use of this product in adverse conditions will void the product warranty.
Let us help you make the most of your next presentation. We offer everything from presentation supplies to tips
for better meetings. And we’re the only transparency manufacturer that offers a recycling program for your used
transparencies. For late-breaking news, handy reference and free product samples, call us toll-free in the
continental United States and Canada, 24 hours a day, or visit our Internet Website.
3M Austin Center
Building A145-5N-01
6801 River Place Blvd.
Austin, TX 78726-9000
QR47301
3M Canada
P.O. Box 5757
London, Ontario
N6A 4T1
3M Mexico, S.A. de C.V.
Apartado Postal 14-139
Mexico, D.F. 07000
Mexico
3M Europe
Boulevard de l’Oise
95006 Cerge Pontoise Cedex
France
Litho in Japan
Copyright © 2001 3M IPC.
All Rights Reserved
78-6970-9094-8 Rev.A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement