Craftsman | 115 | User's Manual | Craftsman 115 User's Manual

OPERATOR'S
MANUAL
318 in. DRILL-DRIVER
VARIABLE SPEED/REVERSIBLE
Model Nos,
315.115340 -12 Volt
315,115350 -14,4 Volt
_,
WARNING: To red_)cethe risk of in}ury,
the L_Se_
must read and understandthe
operator's manual before using this
product.
Customer
Sears,
Help Line: 1-800-932-3188
Roebuck
V'_it the Craftsman
983000-709
5-05
and Co., 3333 Beverly
Rd., Hoffman
Estates,
IL 60179 USA
web page: www.sears.com/craftsman
Save this manual
for future
reference
•
Warranty ..........................................................................................................................................................................
• Introduction .........................................................................................................
•
2
............................................................ 2
GenaraJ S_.fetyRules....................................................................................................................................................
3-4
• Speciitc Sataty RuTes.......................................................................................................................................................
•
4
Safety Rules for Charger .......................................................................................... ;...................................................... 5
== Symbols........................................................................................................................................................................
• Features...............................................................................................................................................................
6-7
_........ 8-9
• Assembly .........................................................................................................................................................................
9
•
Operation..................................................................................................................................................................
10-15
•
Maintenance.............................................................................................................................................................
16-17
•
Exploded View and Parts List...................................................................................................................................
18-1g
•
Parts Ordering/Service ....................................................................................................................................
Back Page
ONE YEAR FULL WARRANTY ON CRAFTSMAN TOOL
If this Craftsman tool fails to give €omplate satisfactionwithin one year from date of purchase, RETURN IT TO THE
NEAREST SEARS STORE IN THE UNITED STATES, and Sears will replace it, free of charge.
If this Craftsman tool is used for cornmemialor rental purposes, this warranty applies for only90 days from the date of
purchase.
This warranty gives you specific legal fights, and you may also have other dghts which vary from state to state.
Sears, Roebuck and Co., Dept. 817 WA, Hoffman Estates, IL 60179
This tool has many features for making "¢.suse more pleasant and enjoyable. Safety, pertom_nce, and dependability
have been given top priority in the design of this product making it easy to maintain and operate.
2
•
Do not overreach. Keep proper footing and balance
at all 5rues. Proper foo_ng and ba_nce enable be_er
cOnLTO[
of the tool in unexpected situations.
• Use safety equipment. Nwaye wear eye protection.
Dust mask, non-skidsafety shoes, hard hat, or hearing
protectionmust be used for appropriate conditions.
• Do notwear loose clothing or jewelry. Contain long
hair. Looseclothes, jewelry, or long hair can be drawn
into ah"vents.
• Do not use on a ladder or unstable support. Stable
tootingon a solid surface scabies better controlof the
too[in unexpected situatbns.
WARNING!READANDUNDERSTAND
ALLINSTRUCTIONS. Failureto follow all instructions§sted
below may result in electric shock, ('ire and/or sadous
personsi intury.
SAVE THESE INSTRUCTIONS
WORK AREA
• Keepyourwork ares clean sndwsll lit. Cluttered
benches and dark areas invite accidents`
• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liqulde, gases, or dust. Power tools create sparks which
may igNte the dust or fumes.
• Keep bystanders, children, andvisitora awaywhile
operating a power tool. DislTactionscan cause you to
lose contm[.
TOOL USE AND CARE
• Use damps or other pracfieal way to secure and
support the workplece to • stable platform. Holding
the work by hand or against your body is uns_ble and
may lead to Tossof con_'ol.
• Do not force tool. Use the correct tool for your application. The correct too[will do the job better and
safer at the rate for which it is designed.
• Do sot use tool if switch does not turn it on or off.
A tool that cannot be controlled with the switch is dangerous and must be repaired.
• Disconnect battery pack from tool or place the
=witch in the locked or off position before making
any adjustments, changing accessories, or storing
the tool. Such preventivesat'elymeasures reduce the
riskor st_'t_ngthetoo( aucident_iy.
• Store idle tools out of reach of ch|ldren and other
untrained persons. TooLsare dangerous in the hands
of untrainedusers.
• When battery pack is not Jnuse, keep it away from
other metal objects like: paper clips, coins, keys,
nails, screws, or other small metal objects that can
make • connection from one terminal to another.
Shordngthe battery terminals together may cause
sparks, bums, or a fire.
• Maintain tools with care. Keep cutting tools sharp
and clean. Properlymaintainedtools with sharp cutting edges are less likely to bind and are easierto
control
• Check for mlsallgnment or binding of moving parts,
breakage of parts, and any other condition that
may affect the tool's operation. If damaged, have
the tool serviced before using. Many accidents are
caused by poorlymaintained tools.
• Use only accessories that ere recommended by the
manufacturer for your model. Accessories that may
be sui_=blefor one too{ may create a risk of injurywhen
used on another too[.
• Keep the tool end its handle dry, clean and free
from oil and grease, Always use a clean clothwhen
cleaning.Never use brake _uJds,gasoline,petrcleumbased r_oducts,orany strong solvents to oJeanyour
tool. Followingthis rule will reduce the risk of loss of
con_'oland deteriorationof the enclosureplastic.
ELECTRICAL SAFETY
• A battery operated tool with integral batteries or a
separate battery pack must be recharged only with
the specified charger for the battery, A charger that
may be suitable for one type of battery may create a
risk of firs when used with another battery.
• Use battery operated tool onlywlth epeclficaliy designated battery pack. Use of any other batteries may
create a risk of fire.
• Use battery only with charger listed.
MODEL
315.115340
315.115350
BATTERY PACK
130139017
Item No, P.11057
130139014
Item No, _.11007
CHARGER
140302002
Item No. _.1_055
140302003
Item No..9.11006
• Do not abuse the cord. Never use the cord to carry
the charger. Keep cord sway fl'om heat, oil, sharp
edges, or moving parts. Replace damaged cords
immediately, Damaged cords may create e fire.
PERSONAL SAFETY
• Stay alert, watch what you are doing and use common sense when operating • power tool. Do not
Use tool while f_red or under the Influence of drugs,
alcohol, or medication, A moment of inattentionwhile
operating power tools may resultin serious personal
iniury.
• Dress properly. Do notwesr loose clothing or
jewelry. Contain long hair. Keep your heir, clothing,
end gloves away from moving parts. Loose clothes,
jewelry, or long hair can be caught in moving parts.
• Avoid accidental starting. Be sure switch Is in the
looked or off position before inserting battery pack,
Carrying tools with your finger on the switch or inserting the battery pack into a too[ with the switch on
invitesaccidentS.
•
Remove adjusting keys or wrenches before turning
the tool on. A wrench or a key that {s left attached to a
rotating part of the tool may resultin personal in{ury.
3
SERVICE
• Tool service must be performed only by qualified
repair personnel. Service or maintenance performed
bY ur_uaI_fisd per_nnel may resu{t {n a risk of Inju_.
•
Hold tool by insulated gripping surfaces when
performing en operation whore the cutting tool may
contec_thidden _rlng. Contact with a "tire" wire wi_
also make exposed metal parts of the tool "live" and
shock the operator.
•
Know your power tool. Read operator's manual
carefully. Learn ito appnsetions and lirnltetione, as
well as the specific potential hazards rotated to this
tool. Followingthis rule will reduce the risk of electric
shock, fire, or serious injury.
• Always wear safety glasses with side shields.
Everyday glasses have only impaof resistant lenses.
They are NOT safety glasses. Followingthis rule will
reduce the risk of eye il_ury.
•
•
Battery tools do not have to be plugged into an
electTIcal outlet;,therefore, they ere always, In
operating condffion. Be aware of possible hazards
when not using your battery tool or when changing
accessories, Followingthis ru[e will reduce the risk of
eIecbic shock, fire, or serious personal iniury.
Do not place battery tools or their batteries near
fire or heat. This witl reduce the risk of explosionand
possib(yinjury,
• When servicing e tool, use only Identical replacement parts. Follow instructions in the Maintenance
section of this manual. Use of unauthorized parts or
bailumto I'ollcw Mainter_ance Instructions may create a
nsk of shock or iniury.
• Never use a battery that has been dropped or
received a sharp blow. A damaged battery is subisc_
to explosion. Properly dispose of +tdropped or damaged battery tmrnsdia1:e}y.
• Ballades vent hydrogen gas and can explode in
the presence of a source of Ignlfion, such as s pgot
light. To reduce _he risk ol serious personalinjury,
never use any cordtsssproduct in the presence of
open flame. An exploded battery can propel debde and
chemicals. If exposed, flush with water immediately.
•
Do not charge battery tool in a damp or wet Ioce5o_. Fallowingthis rule wilt reduce the risk of electr_,
shock.
•
For best results, your battery tool shou_ be
charged In a location where the temperature Is
more than 50°F but less than 100+i:, Do not store
outside or in vehicles.
•
Under exhume usage or temperature conditions, battery I_aakags may occur. If liquid comes
In contact with your skin, wash Immediately with
soap and water, then ceutralize with lemon jules
or vinegar. If liquid gets into your eyes, flush them
wif_ clean water for at least 10 minutes, then seek
Immediate medical attention. Following this rulewill
reduce the risk of serious personal Inlury.
'_
•
a. That pins on plug ofextension cord _re the
same number, size and shape as those of
plug on charger.
Before using battery charger, read all instructions
end cautionarymarkings in this manual, on battery
charger, battery, and produ_ using battery to prevent
misuse of the productsand possibleinjury or damage.
_IL
•
could resultin a risk of fire and electric shock, ff
extensioncord must be used, make sure:
WARNING! READ AND UNDERSTAND ALL
INSTRUCTIONS. Failureto follow all ins_'uctions
listed below, may result;in e]ecV_cshook, Tire
and(or seriouspersor_l injury.
b. That extension cord is properlywired and in
good etect_cat condition;and
c. That wire size is large enoughfor AC ampere
rating of charger as specified below;
Cord Length {Feet)
25'
50'
Cord Size (AWG)
16
16
HOTII="AWG = AmericanWire Gauge
CAUTION." 3-oreduce the risk of electric shock
or damage to the charger and battery, charge only
nickel-cadmium rechargsable batteries as specificell'/designated on your charger.Other types of
batteries may burst, causing personal injury or
damage.
•
Do not operate charger with a damaged cord or
plug, which €ould causeshoKmgand e{ectr_ shook. If
darnaoed, he_e thech_ger tegk_ced by an Buth_rized
servioem&n,
Do not use charger outdoors or expose to wet or
damp conditions. Water enteringcharger will increase
the risk of electricshock.
• Do not operate charger if ithas received a sharp
blow, been dropped, or othermdsedamaged in any
way. Take it to an authorized servicemanfor eiectlicat
check to determine if the charger is in goodworking
order.
Do not disassemble charger. Take it to an authorized
servicemanwhen serviceor repair is required. Incorrect reassomblymay result in a risk of electricshook or
fire,
• Use of an attachment not recommended or sold
by the batter,/charger manufacturer may result in
a risk of fire, electric shock, or in;_'ryto persons.
Following this rule will reduce the risk of electric shock,
fire, or serious personal iniury.
• Do not abuse cord or charger. Never usethe cord to
carry the charger. Do notpull _hs shargsr cord rather
than the plug when disconnecting from receptacle.
Damage tothe cordorchmg_r couldoccurand create
an electric shock hazard, Replace damaged cords immediately.
• Make sure cord is located so that It will not be
stepped on, tripped over, come in contsct with
•sharp edges or moving parts or otherwise subjected to damage or skess. Thiswill reduce the risk of
accidental fails, whish could cause injury, and damage
to the cord, which could result in electric shook.
• Unplug charger from outlet before attempting any
m_dnte_nce or _isaning to reduce the risk of
elecbio shock.
•
Disconnect charger from the power supply when
not in use. This will reduce the dsk of electric shock
or damage to the charger if metal items shouM f_ into
the opening.It also will help prevent damage to the
charger dunng a power surge.
• Risk of electric shock. Do not touch uninsolated
portionof output connector or uninsuistedbattery
terminal.
• Keep cord end charger from heat to prevent
damage to housing or internal parts.
• Save these instructions. Refer to them frequentJy and
use them to lnstruct otherswho may use this tool If
you loan someone this tool, loan them these instructions also to preventmisuse of the product and
possible Injury.
• Do not let gasoline, oils, petroleum-based produ¢ts,
etc. come In €ontact with plastic parts. They contain
chemicalsthatcan dmTmgs,weaken, or destroyplastic.
• An extsnston cord should not be used unless
absolutely necessary. Use of improper extensioncord
_k
100'
16
WARNING: Some dust created by power sending,sawing, grinding,drilling, and other constructionactivities
contains chemicals knownto cause cancer,birth defects or otherreproductiveharm. Some examples of these
them{cats are:
• _cadJrom _ead-based
palnhs,
= crystanlne silicafrom bricks and cement and othermasonryproducts, and
• arsenic and chromiumfrom chemically-treated lumbar.
Your risk from these exposures varies, depending on how ot_snyou do this type of work. To reduce your exposure
tc these chemicals: work in a we_lvantiisted area, and work with approved safety equipment, such as those dust
masks that are speciallydesigned to filterout microscopicparticles.
5
Some of the following symbols may be used on this tool. Please study them end learntheir meaning. Proper interpretation of these symbolswfl[allow you to operate the tool better and safer.
SYMBOL
NAME
DESIGNATION/EXPLANATION
V
Volts
Voltage
A
Amperss
Current
Hz
Her_.
Frequency (cycles per second)
W
Watt
Power
min
Minutes
Time
AlterrmtingCurrent
Type of current
-.
Direct Current
"[ypeor a characteristicof current
no
No Load Speed
Rotationalspeed, at no load
[]
Class I! Construction
Double-insulated construction
Per Minute
Revolutions,strokes, surface speed, orbits eta., per mince
Wet Conditions Alert
Do not expose to rain or use in damp locations.
Read The Operator's Manual
operator's
manual
before
using
product.
To
reduce the
risk of
Injury,
userthis
must
read and understand
Eye Protection
Always
safetywhen
gogg(es
or safety
glasses
with side shields,
or
a full wear
face shield
operating
this
product.
Safety Alert
Precautionsthat invotveyour safety.
_)
No Hands Symbol
serious
personal
injury.
Fal_umto
keep your
handsawsy from the bk-_dewitt result In
_)
No Hands Symbol
Failure to
keep your
hands away from the blade will result in
serious
personal
injury.
_)
No Hands Symbol
Failure to
keep your
hands away from the blade will result in
serious
personal
injury.
No Hands Symbol
Failureto
keep your hands away from the blade will resultin
serious
personaJinjury.
Hot Surface
To reduce
the dsk of injuryor damage, avoid oontactwith
any
hot surface.
..Jmin
_IL
(_)
6
Thefollowing
signalwords and meaningsare intendecLto expl_n the levels of risk associated with this
product.
SYMBOL
_k
SIGNAL
MEANING
DANGER:
Indicates an imminentlyhazardous situation,which, ff not avoided, will
resultin death or serious injury.
WARNING:
Indicates a potentially hazardoussituation, which, ff not avoided, could
result
indeathor serious
injury.
CAUTION:
indicates a potantialtyhazardous situation,which, if not avoided, rnay
resuffin minor or moderate injury.
CAUTION:
(WithoutSafety Alert SyrnboDIndicates a situationthat may result in
propertydamage.
SERVICE
Servicingrequires extreme care and knowledgeand
should be performed only by a qualified service technician.For service we suggestyou returnthe productto
your nearest AUTHORIZED SERVICE CENTER for
repair.When servicing, use only identioalreptacement
parts.
_,
WARNING: To m/oid seriousparsons1 injury,do not
attempt to use this productuntil you read thoroughly
and understandcompletely the operator's manual
Save this operator'smanual and review fTequentlyfor
contLnuingsaia operatior_and instructing oth_rswho
may use this product.
_,WARNING:
O
The operation of any power tool can resultin foreign objects being thrown into your eyes, which
c_n result in severeeye damage. Beforebeginning power tool operation,always wear safety goggles or safety glasseswith side Shields,or a full face shield when needed. We recommendWide
Vision SaFetyMask for Hss over eyeglasses or standard safety gl_sses with side shielc_s,Always
use eye protection which is marked to complywith ANSI Z87.1.
SAVE THESE INSTRUCTIONS
7
PRODUCTSPECIFICATIONS
MODELNO.315.t15340
Chuck .......................................................... 3/8 in. Keyless
Motor .................................................................. 12 Volt DC
MODEL NO. 3t5.t15350
Chuck .......................................................... 3/8 in. Ksyles=
Motor .................................................................. 14 Volt DC
Switch.......................................................... Variable Speed
No Load Speed ................................................. 0-600/rain.
Clutch ................................................................ 24 Position
Switch.......................................................... Variable Speed
No Load Speed ................................................. 0-600/min.
Clutoh.......:........................................................ 24 Position
Torque.................................................. Maximum 100 in.lb.
Torque.................................................. Maximum 110 in.lb.
Charger Pnput................................... 120 V, 60 HT_,
AC only
Charge Rate ............................................................ 3 hours
Charger hput ................................... 120 V,60 Hz, AC only
Charge Rate ............................................... _............ 3 hours
TORQUE
ADJUSTMENT
RQ_G
LEVEL
DIRECTIONOF
SELECTOR
(FORWARD)REVERSE]
CENTERLOCK)
KEYLESS
CHUCK
SWITCH
TR(GGER
CHARGER
LED
WORKLIGHT
SCREWDRIVER
BITS
BITSTORAGE
REDLED
BATTERY
PACK
ORANGE
LED
8
Fig. 1
KNOWYOURDRILL-DRIVER
See Figure 1.
Before attempting to use this product, familiarizeyourself
with all operating features and safety rules.
BIT STORAGE
LED WQRKLIGHT
The LEDworPJight,located on the front of the tool base,
illuminateswhen the switch _'iggar ts depressed.This
providesextra light for inoreased yisibility.
LEVEL
Bits provided with the drill-drivercan be placed in the
storagearea, located on the base of the drill.
A level is located on the top of the motor housingto help
you keep the drill bit level during use;
DIRECTION OF ROTATION SELECTOR
(FORWARD/REVERSE/CENTER LOCK)
Your drill-driverhas a direction of rotation(forward/reverss/
centei"lock) selector located above the switch _ggar for
changing the direction of bit rotation. Setting the switch
trigger in the OFF (center lock) position helps reduce the
possibilityof accidentalstarting when not in use.
TORQUE AI0klMSTMENT RING
KEYLESS CHUCK
"me keylass chuck allows you to hand-tighten or release
the drill bit in the chuck jaws.
UNPACKING
This producthas been shipped eompiatsly assembled.
• Carefulfyremove the tool and any accessoriesfTomthe
box. Make sure that a_litems listed in the packing list
are included.
•
Inspect the too[ carefullyto make sure no breakage or
damage occurred dunng shipping.
• Do not discard the packing material until you have
carefully inspected and setistactoril¥ operated the tool.
• If any parts are damaged or missing, please call
1-800-932-3188 for ase'_tance.
PACKING UST
Drill-Driver
Battery Pack (2)
Charger
Double-ended Bits (2I
Carrying Case
Operator's Manual
Yourdrill-driverhas a 24-position clutch.The torque
adjustment ring can be turnedto select the right amount
of torque for your application.
VARIABLE SPEED
The variablespeed switch triggar delivers higher speed
with increased ttlgger pressureand lower speed with de,teased triggerpressure.
,P=
41L WARNING: If any parts are missingdo not operate
this tool untilthe missingparts are replaced. Failure
to do so could resultin possible seriouspersonal
injury.
A
WARNING: Do not attempt to modify this tool
or create accessories not recommended for use
with this tool. Any such alterationor modification is
misuse arid coutdresul_in s h_.ardous condition
leadingto possibleserious personalir(|ury.
_1_ WARNING: To preventaccidental startingthat
could cause serious persenaf injury, a_,ays remove
the battery pack _om the too[ when assembling
parts.
•
_1_ WARNING: Do not allow famiSa_tywith tools to
make you careJess.Remember that a careless
fracbon of a second is sufficientto intiict serious
]njury.
_k
Press down on b_ttsry pack to be'sure contacts on
battery pack engage properlywith contacts in charging
stand.
•
The charge indicator light (LED), located on the charging stand, wi_ I'_ghtup red and glow when the eharger
is properly connected to power supply. "Thislight
indicates the charger is operating property. It will
remain on unbl battery pack is removed from charging
stand or charger is disconnectedf_om power supply.
• After normaJusage, 3 hours or k_saof charging time is
required to hJftyrecharge battery pack.
WARNING: Always wear safety gogglesor safety
glasses with side shields when operating tools.
Failureto do so could result in objects being thrown
into your eyes, resulting in poasibisserious injury.
_1= WARNING: Do not use any attachments or acoasseries not recommended by th_ rna_u_oturer of
this tool. The use of attachments or accessories not
recommended can result in serlous personalinjury.
NOTE; If both red and orange LED ind_caforsglow, the
battery pack is deeply or compk=.te0jd(scharged, and
6 hours er longerof chargingtime }s required to fully
rechargethebattery
pack,
APPLICATIONS
You may use this tool for the foUowingpurposes:
• Drilling in wood
• Drilling in ceramics, plastics, fibergtess,and laminates
• Ddlling in metals
Ifthechargerdoes notcharge_hebattery
pack,or
the orange LED corr_nuesto glow after more than 30
m_nutes of chsrg'lng,return the battery pack and charging e.ssemb[yto your nearest Sears Repair Center for
electrical check.
•
•
Mbdng paint
CAUTION: If at any point during the charging
process none of the LEDs are lit, remove the battary pack _'om _e chargerto avoid damaging the
product. DO NOT insert another battery.Return the
charger and battery to your nearest service center
for service or replacement.
The battery packwill become slightlywarm to the
touch while charging.This is normal and does not
indicate a problem.
m Do not place charger in an area of extreme heat or
cold. It wilt work best at normal room temperature.
II When batteries become fully charged, unplug charger
from power supply and remove the battery pack.
CHARGING A HOT BA'rrt=RY PACK
When using your tool continuously, the batteries In your
battery pack will become hot. You should let a hot battery
pack cool down for approximately 30 minutes before
attempting to recharge.
CHARGING THE BAI-I'ERY PACK
The battery pack for this tool has been shippedin a low
charge conditionto prevent possible problems.Therefore,
you should charge overnight priorto use.
NOTE: This situationorgyoccurs when continuoususe of
your ddll causes the batteries to become hot. It does not
occur under nonT_ circumstances.Refer to =CHARGING
THE BATTERY PACI_ for normal recharg]ng of battedes.
If the chargingaasembly does not charge your battery
pack under normal circumstances,return both the battery
pack and chargingassembly to your nearest Sears Repair
Center for electrical check.
NOTE: Batteries will not reach furl oharge the first time
they are charged. Allow several cycles (operationfollowed
by recharging]for them to become fully charged.
• Charge battery pack only w_ththe charging assembly
provided.
•
Make sure power supply is normal householdvoltage,
120 volts, 60 Hz, AC on_y.
• Connect charger to power supply.
• Place battery pack in charging stand.Align raised db
on bat_eP/pack with groove in chargingstan_. See
F/gum 2.
10
BATTERY
PACK
SHOWN
INCHARGER
TO REMOVEBATTERY
PACK
CI'.I_GING
ASSEMBLY
See Figure3.
•
Lock the switch triggeran the drill by placingthe direction of rotation selectorin the center position.
•
Locate the latcheson the side of the battery pack and
depress to releasethe battery pack fTomthe drill.
Remove the battery pack from the drill.
•
REDLED
ORANGELED
CHARGING
STAND
Fig. 2
TO INSTALL BATTERY PACK
See FTgure3.
LATCHES
• Lock the switch trigger on the drillby placingthe direct(on of rotation selector in the center position.
• Place the battery pack in the ddlLAlignthe raised rib
on the bakery pack wtth the groove Inside the drill
CAUTION: When placing baC_tery
paeY,_nthe tool,
be sure raised rib on battery pack alignswith the
bottom of the ddll and latches into place propedy.
Improper installationof the battery pack can _use
damage to internalcomponents.
DEPRESS
UITCHESTO
RELEASE
BAT'rERY
PACK
• Make sure the latches on each side of the battery pack
snap into place and the battery pack issecwed in the
dd[{before beginning operation.
11
F_g.3
A
WARNING:
6artery tools are a(ways in operatirtg
conditfon. Therefore, the switch should always be
locP.ed when not in use or carrying at you_" side.
SWITCH TRIGGER
See Rgure 4.
To turn the driJlON, depress the switch trigger.To turn it
OFF, release the switch trigger.
VARIABLE SPEED
See F/gum 4.
The variable speed switch triggerdelivers higher spee(J
and torque wi_ increased _gger pressureand lower
speed with decreased trigger pressure.
NOTE= You might hear a whistling or ringing noisefrom
the switch during use. Do not be concerned; this isa normal part of the switch function.
DIRECTIONOF
HOTA'I"[ON
SELECTOR
(FORWARD/ REVERSE
/_
LOCK)
VARIABLE
SPEED
SWITCHTRIGGER
REVERSE
Avoid runningthe drll_at low speeds for extswdedperiods
of Lime.Runningat low speeds under constantusage may
cause the drillto become overheated. If this occurs, cool
the drillby running it without a load and at full speed.
KEYLESS CHUCK
See Figure 5.
The drin-driverhas a keytese chuck to tighten or release
dd[[ bits in the chuck jaws. Grasp and holdthe collar of
the chuckwlth one hand. Rotate the chuck body with your
other hand. The arrows on the chuck indicate which direction to rotate the chuck body in order to LOCK (tighten)or
UNLOCK (release)the dr_UbiL
dl_ WARNING: Do not hold the chuck body with one
hand and use the power of the dn'llto tighten the
chuck jaws on the dd]] bit. The chuck body could slip
in your hand, or your hand could sI_pand come in
contact with the rotating drtnbit. This could cause an
accident resulting in serious personalInjury.
DRILLBIT
!
FORWARD
UNLOCK
(RELEASE)
JAWS
Fig. 4
FORWARD/REVERSE/CENTER
LOCK
See FTgure4.
"['hedirection of bit rotation is reversibleand is controlled
by a selector located above the switch trigger. With the
driftheld in nom_aloperating position, the direction of
rotationselector shou[d be positionedto the left of the
switch trigger for drilling.The ddflingdirection is reversed
when the selector isto the right ot the switch t_gger.
LOCI(
(TIGHTEN)
CHUCK
BODY
Flg"5
Setting the switch trigger in the OFF (car_er look) position
helps reduce the possibilityof accidental starting when not
in use.
CAUTION: To prevent gear damage, always allow
the chuck to come to a complete stop before changing the direction of rotation.
To stop the drill, release the switch trigger and allow the
chuck Locome to a complete stop.
NOTE: The drillwill not run unlessthe direction of rotation
selector is pushed fully to the left or right.
12
ADJUSTABLE
TORQUE CLUTCH
LED WORKLIGHT
See F/gum 7.
The drill ls equipped with an adjustable torque clutch for
driving different types of screws into differentmaterials.
The proper setting depends on the type of material and
the size of sorew you are using.
The LED workJighton the foot of the drillwill come on
when the switch _'igger ie depressed.This providesadditional lightingon the surface of the workpieoefor operaLion in lower-lightareas.
ADJUSTING TORQUE
See Ftgure 6.
• There are Lwenty-fourtorque indicatorsettings located
on the _TO_ofthe drill.
• Rotate the adjusting ring to the desired setting.
• 1- 4
For drivingsmed[screws
•
5-8
For drivingscrews into soft
materia_
• g - 12
For ddving screws into soft and hard
materials
• 13 - 16
For drivingscrews into hardwood
=17 - 23
• 4U
For driving large screws
For heavy drifting
TODECREASE
TORQUE
LED
WORKLIGHT
ADJUSTING
R/NO
Fig. 7
Bff STORAGE
See Figure 8.
When not in use, bits providedwith the drill can be placed
in t_e storage area located on the base of the driU.
TOIXCREASE
TORQUE _,
SCREWDRIVER
BIT(S)
\
Fig. 6
BIT
AREA
13
INSTALLING BITS
F/gure 9.
_k
•
Lock the switch trigger by piecing the direction of rotation selector in the center position.
• Open or close the chuck j_zwsto a point where the
opening Lsalight/largar then the bit elze you intend to
use. Also, raise the front of the driftstighttyto keep the
b_ from fa_ling out of the chuck jaws.
• Insert the drill bit straight into the chuck the full length
of the jaws.
• Tighten the chuck jaws on the drill bit.
DRILLBIT
UNLOCK
. (RELEAEE)
WARNING: Make sure to insertthe drillbit straight
into the chuck jaws. Do not insertthe drillbit into
the chuck jaws at an angle then tighten, as shownin
figure 1O.Thls could cause the drill bit to be thrown
from the drill, resultingin possib]e serious personal
injuryor damage to the chuck.
CHUCK
COLLAR
WRONG
LOCK
(TIGHTEN)
Fig. 10
REMOVING BITS
See F_jure g.
•
Lock the sw(tch t_gar by placing the direction of rotation selector in the center position.
• Loosen the chuck jaws from the drillbiL
• To loosen: grasp and hold the collar of the chuck with
one hand,while ro_ting the chuck body with your
other hand.
CHUCK
BODY
RIGHT
Fig. 9
• TOtighten: grasp and hold the collar of the chuck with
one hand, while ro'_ting the chuck body with your
other hand.
NOTE: Rotate the chuck body in the direction at the
arrow ma_sd UNLOCK to loosenthe chuck jaws.
• Do not use a wrench to tighten or loosen the chuck
NOTE: Rotate the chuck body in the direction of the
arrow marked LOCK to tighten the chuck jaws.
• Do not use a wrench to tighten or loosen the chuck
jaws.
•
ja.w8.
14
Remove the driftbit from the chuck jaws.
'_
LEWL
WARNING: Alwayswsar safety goggles or safety
glasseswith aide shields when operating tools. Failure to do so could resultin objects being throwninto
your eyes, resultingin possibleseriousinjury.
DRILLING
See Figure 11.
A level is located on top of the motor housing to help keep
the drill bit level during use.
• Check the direction of rotation selector for the correct
sathng (forward or raverae).
• Secure the material to be drilled in a vise or with
clamps to keep _t'{Tomturning as the ddlt bit rc>_atas.
• Hold the drillfirmlyand place the bit at the point to be
• Depress the switch trigger to start the drill.
• Move the drillbit intothe work,piece, applying only
enough _ress_e to keep the bit cuthng.Do not toms
the driti or apphj side pressure 'coelongate a hole. Let
the tool do the work.
F_g.tl
_lk WARNING: Be prepaxsd for binding a_ bit breakthrough. When these situationsoccur, drillhas a
tendency to grab and kick oppositeto the direction
of rotationand could cause loss ot control when
breaking throughmaterial. )1'not prepared,this loss
of controlcan result inpossible seriousin(ury:.
• When drilling hard, smooth surfaces, use a center
punch to mark the desired hole location. Thiswill prevent the dn'ilbit from slippingoff-center as the hole is
started.
• When drillingmetals, use a light oil on the drill bit to
keep it from overheating.The oil will prolong the life ot
the bitand increase _e driltingaction.
• If the bit )aresin the workpieca or it the ddll stalls,
stop the tool irnmed_tel'/. Remove the bit from the
workpiece and determinethe reasonfor jamming.
This drillhas an elecb'Jobrake. When the switch trigger
isreleased, the chuck stops turning,When the brake is
functioning properly,sparks will be visiblethroughthe
vent slots on the housing.This is normal and is the action
of the brake.
15
_I_
WARNING: When servicing, use on3yidentical
Craftsman replar.sment parts. Use of any other paTt
may create a hazard or cause product damage.
CHUCK REMOVAL
See F-_ums 12- 14.
The chuci( may be removed and replaced bye new one.
•
_k
WARN|NG: Always wear safety goggles or safety
gta.sesswith side shields when using compressed air
to clean tools. ITthe operation is dusty,siso wear a
dust mask.
Lock the switch triggerby placing the directionof rotation selector in center position.
•
|nsert a 5116 in. or larger hex key into the chuck of the
driUarid tighten the chuck jaws securely.
• Tap the box key sharplywith a ma[(et in a clockwise
direc_on. This w|_ loosen the scrs_, _nthe ohucY,tot
easy removal
_lk WARNING: To avoid serious personalinjury,always
remove the battery pack from the tool when cleaning
or performingany maintenance.
G ENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plasticsare susceptible to damage from various types st
commemia] solventsand may be damaged by their use.
Use clean cloths to remove dirt, dust, sit, grease, eta.
_1_ WARNING: Do not at any time let brake fluids,
gasoline, petroleum-based products, penetrating
oils, etc. come ]n con'_ct with plastic parts. ChsmiPals can damage, weaken or destroy plasticwhich
may result in serious personalinjury.
Only the parts shown on the parts [(st are intended to be
repairedor rep(aced by the customer.All other parts
should be replaced at a Sears Service Center.
KEYt,.ESS
CHUCK
Fig. "t2
•
Open the chuck jaws and remove the hsx key. Using a
scrawdriver,remove the chuck screw by b._'ningit in a
clockwise
direction.
NOTE: The screw has left hand threads.
SCREWDRIVER
Fig. 13
16
• Insert the hex key into the chuck and tighten the chuck
jaws sacurety.Tap sharplywith a m_et in a counterclockwise d_rection.This wilt loosenthe chuck on the
BA'rrERIES
The battery pack for this tool is equipped with nickel-cadmium rechargeabiebatteries. Length of servicefrom each
charging willdepend on the type of work you are doing.
spindle. It can now be unscrewed by hand.
The batteriesin this tool have been designed 10 provide
maximum b-ouble-frse life. However, llke all batteries, they
w[Uevantusllywear ouL Do not disassemble battery pack
and attempt to replace the batteries. H_ndtingof these
batteries, especiallywhen wearing rings and jewelry,could
result in a serious burn.
N_-_ET
To obtain the longest possible battery life, we suggestthe
foUoWing:
•
Remove the battery pack from the charger once it is
futly charged and ready for use.
For battery pack storage longer than 30 days:
•
Store the battery pack where the temperature is below
80°F.
•
Store battery packs in a "discharged" condition.
BATTERY PACK REMOVAL AND
PREPARATION FOR RECYCLING
To preservenatural resources,please
mcyc_ ordispose of t_tteries
properly.
ThLs productcontains nickel-cadmium
batteries, Local, state or federal
laws may prohibitdisposal of nickelcadmium batteries in ordinary b'esh.
Consult your local waste authority for information
regardingavailab[e recyclingand/or c_ispoea(options.
Fig. 14
TO RETIGHTEN A LOOSE CHUCK
l'ha chuck may become loose on the spindle and develop
a wobble. Periodicallycheck the chuck.screwfor tightne_s.
• Lock the switch trigger by placing the directiono! rotation selector in the canter position.
_k
• Open the chuck iaws.
• insert the hex key into the chuck and _ghten the chuck
jaws sscurel'/. "Tapthe hex key sharplyw_h a mallet in
a clockwise direction.This will tighten the chuck on the
spindle.
• Open the chuck jaws and remove the hax key.
• Tighten the chuck screw.
NOTE: The chuck screw has left hand threads.
17
wARNING: Upon removal, cover the battery pack's
terminalswith heaw-duty adhesive tape, Do net
attempt to destroy or disessemb_eb_tary pack or
remove any of its components. Nickel-cadmium
batteriesmust be recycled or d(spossd of properly.
Also, never touch both terminals with metal objects
andJor body p_'ts as short circuit may result. Keep
away from c_ldren. Failureto comply with these
warnings could result in fire and/or serious injury.
_-
CRAFTSMAN
12 VOLT DRILL-DRIVER
- MODEL NUMBER
315,115,340
-.----.--ii
number
[nall
correspondence
regarding
yourDRILL-DRIVER
orwhen
ordering
repair
parts,
The model
number
w([[ ba found
on a plats
attachedtothemotor
housing.
Alwaysmentionthemodel
SEE BACK PAGE FOR PARTS ORDERING
J
|
INSTRUCTIONS
2
1
\
4
5
\
PARTS LIST
Key
No.
Part
Number
1
2
3
4
5
6
6612001
6903326
9,;0237076
140302002
130139017
300912192
983000709
DesQription
Qty.
Chuck Screw ..............................................................
I
Chuck .........................................................................................................
1
Data Plate ..................................................................................................
1
* Charger (Item No, _tl 1057) ..........................................................................
1
* Battery Pack (Item No. _-11055}.................................................................. 2
Carrying Case (Not Shown) ........................................................................ 1
Operator's Manual
• Can Be Purchased Thru RSOS (Retail Special Order System)
18
CRAFTSMAN
14A VOLT DRILL-DRIVER
- MODEL NUMBER
315.1t5350
I
number
in artcorrespondence
regarding
your
DRILL-DRIVER
or when
ordering
repair
parts. the model
J The
model
number will be found
on a plate
attached
to the motor
housing.
Always
mention
SEE BACK PAGE FOR PARTS ORDERING
|
INSTRUCTIONS
2
1
\
5
\
PARTS LIST
Key
No.
Part
Number
1
2
3
4
5
6
6612001
6903326
940237074
140302003
13O139014
300912193
983000709
Oescription
Qty.
Chuck Screw ............................................ .................................................. 1
Chuck .........................................................................................................
1
Data Plate ...................................................................................................
1
"Charger (Item No. _.110C_)..........................................................................
"Battery Pack _ltem No. 211007) ..................................................................
Carrying Case (Not Shown) ........................................................................
Operator's Manual
* Can Be Purch=sed Thru RSOS (Fletail Special Order System)
19
1
2
1
Your Home
For repair-in your home-of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold PJ
For the replacement parts, accessories and
owner's manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME
®
(l-_o-4ss-4ss3)
Call any'dine, clay or night (U.S.A.
www.sears.com
and Canada)
www,seal_.Ca
ill
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call or go on-line for the location of your nearest
Sears Parts & Repair Center.
1-800-488-1222
Call any6me, day or night (U.S J_. only)
www_rs.co111
To purchasea protectionagreement(U.S.A.)
or maintenanceagreement(Canada) on a productservicedby Sears:
1-800-827-6655
(u.s.A_)
PaPa pedir servicio de reparacibn
a domici5o, y para ordanar piezas:
1-888-SU-HOGAR
=
1-800-361-6665
(Canada)
Au Canada pour service en frontals:
1-800-LE-FOYER _c
O-soo-s33-s_7)
(1-888-784-6427)
_ Registmed Trademark I _ Trademark I _ _x,/icQ V_rk of Seres, Roe_jck and _.
0 Mar_ P_ada
I'm Marca de F_txlca I su Marca de Seriic]o de Sears, Roobuck a_
r'_ Mar_pJe do €o_mrcQ I _m I_
d6pos_ de Serum, Roebuck er_l Co.
_.seal_.Ca
_.
© seam, Roebuck and CO.
Download PDF

advertising