Craftsman | 16278350 | User's Manual | Craftsman 16278350 User's Manual

User Instructions
Shop Phone
Model 27413
5. Slots and openings in the cabinet back or bottom are provided for
ventilation, to protect it from overheating. These openings must
not be blocked or covered. The openings should never be
blocked by placing the product on the bed, sofa, rug, or other
similar surface. This product should not be placed in a built-in
installation unless proper ventilation is provided.
11. Do not store this product, or the battery(ies) provided with or
identified for use with this product, in high-temperature areas.
Batteries that are stored in a freezer or refrigerator for the
purpose of extending shelf life should be protected from
condensation during storage and defrosting. Batteries should be
stabilized at room temperature prior to use after cold storage.
6. This product should be operated only from the type of power
source indicated on the marking label. If you are not sure of the
type of power supply to your home, consult your dealer or local
power company.
12. If your product uses rechargeable battery(ies), charge the
battery(ies) only in accordance with the instructions and
limitation specified in the User Manual.
7. Do not allow anything to rest on the power cord. Do not locate
this product where the cord will be abused by persons walking
on it.
8. Do not overload wall outlets and extension cords as this can
result in the risk of fire or electric shock.
9. Never push objects of any kind into this product through cabinet
slots as they may touch dangerous voltage points or short out
parts that could result in a risk of fire or electric shock. Never
spill liquid of any kind on the product.
CALL BACK
TALK
FORMAT
1
2 abc
3 def
4 ghi
5 jkl
6 mno
8 tuv
9 wxyz
7 pqrs
exit
*
tone
redial
delete/channel
0
oper
ringer
# pause
memory
10. To reduce the risk of electric shock, do not disassemble this
product, but take it to a qualified serviceman when service or
repair work is required. Opening or removing covers may expose
you to dangerous voltages or other risks. Incorrect reassembly
can cause electric shock when the telephone equipment is
subsequently used.
11. Do not expose the product to extreme temperatures such as
areas near a hot radiator or stove or in a hot car.
EQUIPMENT APPROVAL INFORMATION
Your telephone equipment is approved for connection to the Public
Switched Telephone Network and is in compliance with parts 15 and
68, FCC Rules and Regulations and the Technical Requirements for
Telephone Terminal Equipment published by ACTA.
1 Notification to the Local Telephone Company
On the bottom of this equipment is a label indicating, among other
information, the US number and Ringer Equivalence Number (REN)
for the equipment. You must, upon request, provide this
information to your telephone company.
The REN is useful in determining the number of devices you may
connect to your telephone line and still have all of these devices
ring when your telephone number is called. In most (but not all)
areas, the sum of the RENs of all devices connected to one line
should not exceed 5. To be certain of the number of devices you
may connect to your line as determined by the REN, you should
contact your local telephone company.
program/flash
12. Do not place lighted candles, cigarettes, cigars, etc., on the
telephone.
13. Never touch uninsulated telephone wires or terminals unless the
telephone line has been disconnected at the network interface.
14. Never install or modify telephone wiring during a lightning storm.
15. Never install telephone jacks in wet locations unless the jack is
specifically designed for wet locations.
16. Use caution when installing or modifying telephone lines to
prevent electrical shock and/or fire.
17. Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
A. When the power supply cord or plug is damaged or frayed.
B. If the product has been exposed to rain or water.
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
www.sears.com/craftsman
C. If the product does not operate normally by following the
operating instructions.
D. If the product's cabinet has been damaged.
WARRANTY
ONE-YEAR FULL WARRANTY
If this Craftsman Shop Phone is defective in material or workmanship
within one year from the date of purchase, RETURN IT TO YOUR
NEAREST SEARS STORE in the United States, and it will be replaced
free of charge. The batteries supplied with this phone are expendable
parts not covered by this warranty. This warranty gives you specific
legal rights, and you may also have other rights which vary from state
to state.
Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179
HELP LINE
E. If the product exhibits a distinct change in performance.
18. Avoid using a telephone (other than a cordless type) during an
electrical storm. There may be a remote risk of electric shock
from lightning.
19. Do not use the telephone to report a gas leak in the vicinity of
the leak.
20. Do not place this product on an unstable cart, stand or table. The
product may fall, causing serious damage to the product.
IF YOUR PRODUCT UTILIZES BATTERIES, THE FOLLOWING
ADDITIONAL PRECAUTIONS SHOULD BE OBSERVED:
1. Use only the type and size battery(ies) specified in the user
manual.
2. Do not dispose of the battery(ies) in fire. They may explode.
Check with local codes for possible special disposal instructions.
For assistance in the use of this product, please call the following
Toll-Free Help Line: 1-800-448-0329, and tell the representative that
you have a Sears Craftsman Shop Phone.
3. Do not open or mutilate the battery(ies). Released electrolyte is
corrosive and may cause damage to the eyes or skin. It may be
toxic if swallowed.
If the equipment is causing harm to the telephone network, the
telephone company may request that you disconnect the equipment
until the problem is resolved.
4.
Attach your sales receipt to this booklet for future reference or jot
down the date this product was purchased or received as a gift. This
information will be valuable in the unlikely even that the product
develops problems during the warranty period.
Purchase Date:___________________________________________
Name of Store:____________________________________________
IMPORTANT SAFETY INSTRUCTIONS
Some of the following information may not apply to your particular
product; however, when using telephone equipment, basic safety
precautions should always be followed to reduce the risk of fire,
electric shock and injury to persons, including the following:
5.
Exercise care in handling battery(ies) in order not to short out the
battery(ies) with conducting materials such as rings, bracelets, and
keys. The battery(ies) or conductor may overheat and cause burns.
Do not attempt to recharge the battery(ies) provided with or
identified for use with this product that are not intended to be
charged. The battery(ies) may leak corrosive electrolyte or explode.
6. Do not attempt to rejuvenate the battery(ies) provided with or
identified for use with this product by heating them. Sudden
release of the battery(ies) electrolyte may occur causing burns
or irritation to eyes or skin.
7. When replacing battery(ies), all batteries should be replaced at
the same time. Mixing fresh and discharged batteries could
increase internal cell pressure and rupture the discharged
battery(ies). (Applies to products employing more than one
separately replaceable primary battery.)
2. Follow all warnings and instructions marked on the product.
8. When inserting battery(ies) into this product, the proper polarity
or direction must be observed. Reverse insertion of battery(ies)
can cause charging, and that may result in leakage or explosion.
3. Unplug this product from the wall outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
9. Remove battery(ies) from this product if storing over 30 days
because the battery(ies) could leak and damage the product.
4. Telephones should not be used while you are in a bathtub,
shower or pool. Immersion of the telephone or handset in water
could cause an electrical shock.
10. Discard "dead" battery(ies) as soon as possible since "dead"
batteries are more likely to leak in a product.
1. Read and understand all instructions.
A plug and jack used to connect this equipment to the premises
wiring and telephone network must comply with the applicable
FCC Part 68 rules and requirements adopted by the ACTA. A
compliant telephone cord and modular plug is provided with this
product. It is designed to be connected to a compatible modular
jack that is also compliant. See installation instructions for details.
Notes
• This equipment may not be used on coin service provided by
the telephone company.
• Party lines are subject to state tariffs, and therefore, you may
not be able to use your own telephone equipment if you are on
a party line. Check with your local telephone company.
• Notice must be given to the telephone company upon
permanent disconnection of your telephone from your line.
• If your home has specially wired alarm equipment connected to
the telephone line, ensure the installation of this product does
not disable your alarm equipment. If you have questions about
what will disable alarm equipment, consult your telephone
company or a qualified installer.
2 Rights of the Telephone Company
Should your equipment cause trouble on your line which may harm
the telephone network, the telephone company shall, where
practicable, notify you that temporary discontinuance of service may
be required. Where prior notice is not practicable and the
circumstances warrant such action, the telephone company may
temporarily discontinue service immediately. In case of such
temporary discontinuance, the telephone company must: (1) promptly
notify you of such temporary discontinuance; (2) afford you the
opportunity to correct the situation; and (3) inform you of your right to
bring a complaint to the Commission pursuant to procedures set forth
in Subpart E of Part 68, FCC Rules and Regulations.
The telephone company may make changes in its communications
facilities, equipment, operations or procedures where such action is
required in the operation of its business and not inconsistent with FCC
Rules and Regulations. If these changes are expected to affect the
use or performance of your telephone equipment, the telephone
company must give you adequate notice, in writing, to allow you to
maintain uninterrupted service.
HEARING AID COMPATIBILITY (HAC)
This telephone system meets FCC standards for Hearing Aid
Compatibility.
US Number is located on the cabinet bottom
REN number is located on the cabinet bottom
INTRODUCTION
CAUTION: When using telephone equipment,
there are basic safety instructions that should
always be followed. Refer to the IMPORTANT
SAFETY INSTRUCTIONS provided with this
product and save them for future reference.
This telephone has been designed to be simple to use,
however, you can reach its full potential more quickly by
taking a few minutes to read this user’s Guide. This
telephone is a multifunction product for use with the Call
Waiting Caller ID services available from your local
telephone company.
Your Call Waiting Caller ID phone stores and displays
specific information, provided by your local telephone
company, to subscribers of Caller ID or similar caller
identification services.
HANDSET, BASE AND REMOTE
CHARGER LAYOUT
Your Call Waiting Caller ID phone allows you to:
• View the name and telephone number of a caller.
• Identify callers before you answer the phone.
• Store up to 40 Caller ID records sequentially.
• Know who is calling while you are on the phone or
when you are away.
IMPORTANT: In order to use all of the Caller ID
features of this phone, you must subscribe to either
the standard Name/Number Caller ID Service or Call
Waiting Caller ID Service. To know who is calling while
you are on the phone, you must subscribe to Call
Waiting Caller ID Service.
IMPORTANT: Because cordless phones operate on
electricity, you should have at least one phone in your
home that isn’t cordless, in case the power in your
home goes out.
CALL BACK/
TALK button
2 abc
3 def
4 ghi
5 jkl
6 mno
7 pqrs
8 tuv
9 wxyz
tone
redial
0
oper
ringer
# pause
memory
program/flash
delete/channel
1. Press the program/flash button until 1TONE 2PULSE
shows in the display.
memory button
2. Use the cid/vol (+/> or -/<) buttons or the handset
touch-tone pad to select 1TONE if you have touch-tone
service or 2PULSE if you have rotary service.
program/flash
button
delete/channel
button
Battery pack
Warning: To prevent
fire or electrical shock
hazard, do not
expose this product
to rain or moisture.
The exclamation
point within the
triangle is a warning
sign alerting you of
important
instructions
accompanying the
product.
DEFAULT SETTING
You may use the factory default settings or your
own settings.
antenna
page
CONNECTING THE TELEPHONE LINE
1. Press the program/flash button until DEFAULT shows in
the display, NO is the default setting.
1. Connect one end of the telephone line cord to the LINE
jack on the bottom of the base.
2. Use the cid/vol (+/> or -/<) buttons or the handset
touch-tone pad to select NO to use your settings or
YES to restore the factory default settings.
2. Connect the other end of the telephone line cord to a
telephone jack on the wall.
telephone jacks
Handset charge cradle
3. Press program/flash to store selection.
ringer button
page button
in use/page
indicator
3. Press program/flash to store selection.
# pause button
exit
*
redial button
2. Use the cid/vol (+/> or -/<) buttons or the handset
touch-tone pad to move the arrow to 1, 2 or 3.
Set your phone according to the type of service you are
subscribed to.
FORMAT
1
FORMAT button
1. Press the program/flash button until RINGERTONE
shows in the display. 1 is the default setting.
TONE/PULSE DIALING
TALK
Risk of electric shock
Do not open
Caution: To reduce the risk of
electric shock, do not remove
cover (or back). No user
serviceable parts inside. Refer
servicing to qualified service
personnel.
You may choose from three different ringer tones.
CALL BACK
Caution:
The lightning flash
and arrow head
within the triangle is
a warning sign
alerting you of
“dangerous voltage”
inside the product.
The battery packs are interchangeable. While one battery
pack is charging, the other is in use. To remove the battery
pack from the handset, push in on the tabs and pull. To
attach the battery pack to the handset, snap the battery
pack onto the bottom of the handset.
cid/vol (+/> or -/<)
buttons
• Screen unwanted calls, eliminate harassment from
annoying calls, or to get prepared before answering a call.
To get the most from your new phone, we suggest that
you take a few minutes right now to read through this
user's guide.
RINGER TONE
INSTALLING THE PHONE
Display
• View the time and date of each incoming call.
SWITCHING BATTERY PACKS
3. Raise the antenna on the base.
Battery charge cradle
See marking on bottom / Back of product
3. Press program/flash to store selection. You will hear a
confirmation tone.
CONNECTING THE AC (ELECTRICAL)
POWER
TELEPHONE OPERATION
1. Plug the base into an electrical outlet.
BEFORE YOU BEGIN
HANDSET REGISTRATION
2. Place the remote charger on a flat surface. Plug the
power supply into an electrical outlet.
The handset is pre-registered. If your handset is not
registered, follow these steps:
PARTS CHECKLIST
Allow the system to charge for 16 hours prior to first use.
If you don’t properly charge the phone, battery
performance is compromised.
1. Make sure the phone is OFF (not in TALK mode).
Make sure your package includes the items shown here.
INSTALLING THE BATTERY PACK
AC Power supply cord
CALL BACK
TALK
Charge indicators
1. Detach the battery pack from the handset by pressing
the side tabs.
FORMAT
1
4 ghi
7 pqrs
2 abc
5 jkl
8 tuv
3 def
2. Remove the "Prior to Use" tag.
page
6 mno
9 wxyz
exit
*
tone
redial
delete/channel
Remote charger
with battery pack
0
oper
ringer
# pause
memory
program/flash
Handset with
battery pack
Base unit
Telephone
line cord
TELEPHONE JACK REQUIREMENTS
To use this phone, you need an RJ11C
type modular telephone jack, which
might look like the one pictured here,
installed in your home. If you don’t
have a modular jack, call your local
phone company to find out how to
get one installed.
Wall plate
Modular
telephone
line jack
INSTALLATION NOTE: Some cordless telephones
operate at frequencies that may cause interference to
nearby TVs, microwave ovens, and VCRs. To minimize
or prevent such interference, the base of the cordless
telephone should not be placed near or on top of a
TV, microwave ovens, or VCR. If such interference
continues, move the cordless telephone farther away
from these appliances.
DIGITAL SECURITY SYSTEM
Your cordless phone uses a digital security system to
provide protection against false ringing, unauthorized
access, and charges to your phone line.
When you place the handset in the base, the unit verifies
its security code. After a power outage or battery
replacement, you should place the handset in the base for
about 20 seconds to reset the code.
IMPORTANT INSTALLATION
INFORMATION
• Never install telephone wiring during a lightning storm.
• Never install telephone jacks in wet locations unless the
jack is specifically designed for wet locations.
• Never touch non-insulated telephone wires or terminals,
unless the telephone line has been disconnected at the
network interface.
• Use caution when installing or modifying telephone lines.
• Temporarily disconnect any equipment connected to the
phone such as faxes, other phones, or modems.
IMPORTANT INSTALLATION GUIDELINES
• Install telephone near both a telephone (modular) jack
and an electrical power outlet.
• Avoid sources of noise, such as a window by a busy
street, and electrical noise, such motors, microwave
ovens, and fluorescent lighting.
3. Re-attach the battery pack to the handset.
4. Place the handset in the charge cradle on the remote
charger and charge for 16 hours prior to first use.
NOTE: If you don't properly charge the handset,
battery performance is compromised.
5. Place the extra battery pack on the battery charge cradle
on the remote charger and charge for 16 hours prior to
first use.
SET UP
There are five programmable menus available:
Language, Area Code, Ringer Tone, Tone/Pulse Dialing,
and Default Setting.
NOTE: To program these settings, the handset must
be OFF (not in TALK mode).
LANGUAGE
Set the display language to show messages in either
English, Spanish, or French.
• Avoid heat sources, such as heating air ducts, heating
appliances, radiators, and direct sunlight.
1. Press the program/flash button until 1ENG 2FRA 3ESP
shows in the display.
• Avoid areas of excessive moisture or extremely low
temperature.
2. Use the cid/vol (+/> or -/<) buttons or the handset touchtone pad to choose 1ENG (English), 2FRA (French) or 3
ESP (Spanish).
• Avoid dusty locations.
• Avoid other cordless telephones or personal computers.
CHARGING THE BATTERY PACKS
For your convenience, this shop phone includes two
rechargeable battery packs. One battery pack is attached to
the bottom of the cordless handset, and the other is
attached to the top of the recharge cradle. While one is in
use, the other is charging.
3. Press program/flash to store selection.
AREA CODE
2. Press and hold the format button on the handset until
you hear a beep and PRESS AND HOLD BASE PAGE KEY
shows in the handset's display.
3. Move the handset close to the base.
4. Press and hold the base page button.
NOTE: You must press the page button on the base
within 30 seconds to continue registration.
5. You will hear a confirmation tone when the registration
is complete, and the handset's display shows
REGISTERED.
MAKING A CALL
1. Press the CALLBACK/TALK button.
2. When you hear a dial tone, dial a telephone number.
Or
Dial the phone number first, then press the CALLBACK/
TALK button.
3. When finished, press the CALLBACK/TALK button again
to hang up.
ANSWERING A CALL
1. Pick up the handset and press the CALLBACK/TALK button.
NOTE: The CALLBACK/TALK button is disabled
when the handset is in the remote charger cradle.
2. To disconnect a call, place the handset back in the
cradle on the remote charger or press the CALLBACK/
TALK button again.
REDIAL
While the phone is on, press the redial button to immediately
redial the last number you dialed (up to 32 digits). If you get a
busy signal, and want to keep dialing the number, just press
redial again (you don't have to turn the phone off and back on).
1. Press the program/flash button until AREA CODE --shows in the display. --- is the default setting.
FLASH
2. Use the handset number pad to enter your three digit
area code.
Use the program/flash button to activate custom calling
services such as call waiting or call transfer, which
are available through your local phone company.
NOTE: If you make a mistake, press the delete/
channel button to erase the wrong area code and
repeat step 2.
3. Press program/flash to store selection.
TIP: Don’t use the CALLBACK/TALK button to
activate custom calling services such as call waiting, or
you’ll hang up the phone.
CHANNEL BUTTON
CALL WAITING CALLER ID
3. Press CALLBACK/TALK button. The number dials
automatically.
While talking, you might need to manually change the
channel in order to get rid of static. Press and release
the delete/channel button to advance to the next
channel. The current channel number appears on the left
side of the display.
To receive Caller ID information for a Call Waiting call, you
must subscribe to the combined Call Waiting Caller ID
service from your local telephone company. Call Waiting
Caller ID service allows you to see Caller ID information
for an incoming call while you are on the telephone.
The in use indicator is lit when the handset is charging in the
cradle on the base or when the phone is ON. It flashes when
you receive a call or when the page button is pressed.
TEMPORARY TONE
This feature is useful only if you use pulse dialing service.
Temporary tone dialing enables pulse (rotary) service
phone users to access touch-tone services offered by
banks, credit card companies, etc. For example, when you
call your bank you may need to enter your account
number. Using the temporary tone feature allows you to
temporarily switch to touch tone mode so you can enter
and send your number.
1. Dial the telephone number and wait for the line to connect.
2. When your call is answered, press the *tone/exit button
on your handset number pad to temporarily change
from pulse dialing to tone dialing.
3. Follow the automated instructions to get the information
you need.
4. Hang up the handset and the phone automatically
returns to pulse (rotary) dialing mode.
IMPORTANT: In order to use all of the Caller ID
features of this unit, you must subscribe to either the
standard Name/Number Caller ID Service or Call
Waiting Caller ID Service. To know who is calling
while you are on the phone, you must subscribe to
Call Waiting Caller ID Service.
RECEIVING AND STORING CID
RECORDS
When you receive a call, the information is transmitted by
the phone company to your Caller ID telephone between
the first and second ring.
When the memory is full, a new call automatically
replaces the oldest call in memory. NEW appears in the
display for calls received that have not been reviewed.
REPT indicates that a new call from the same number was
received more than once.
NOTE: Check with your local phone company
regarding name service availability.
CANCEL
As calls are received and stored, the display is updated to
let you know how many calls have been received.
FINDING THE HANDSET
This feature helps locate a misplaced handset.
• Press the cid/vol (-/<) arrow button to scroll through the
call records from the most recent to the oldest.
Press the page button on the base. The handset beeps
continuously for about two minutes or until you press any
button on the handset. You may also press page to cancel.
• Press the cid/vol (+/>) arrow button to scroll through the
call records from the oldest to the newest.
NOTE: The ringer does not have to be ON for this
feature to work.
RINGER BUTTON
TRANSFERRING CID RECORDS TO
MEMORY
You may transfer a CID record to your phone’s memory.
Three options are available: RINGER OFF, LOW, and HIGH.
The default setting is RINGER LOW.
1. When the phone is OFF (not in TALK mode), press
RINGER once to listen to the current ringer tone.
2. Use the cid/vol (+/> or -/<) buttons to choose the ringer
level you want.
3. Press RINGER again to store selection. The desired
setting shows in the display.
NOTE: It is important that you format CID records
correctly before storing in memory. It is not possible
to re-format CID records stored in memory.
1. Use the cid/vol (-/<) arrow or cid/vol (+/>) arrow button
to scroll to the desired record.
2. Press the memory button.
CHANGING THE CID NUMBER FORMAT
The format button lets you change the format of the
displayed CID number. The available formats are as follows.
1. Use the cid/vol (-/<) arrow or cid/vol (+/>) arrow button
to scroll to the number you want to call back.
2. If the number will not dial as shown, press the format
button. Repeat if necessary, until the correct number of
digits are shown.
3. Press CALLBACK/TALK button. The number dials
automatically.
MEMORY
Store up to 10 24-digit numbers in memory for quick
dialing. This memory feature is in addition to the 40 Caller
ID records that can be stored in the Caller ID memory log.
STORING A NAME AND NUMBER IN
MEMORY
1. Make sure the phone is OFF (not in TALK mode).
2. Press the memory button.
3. Press the desired memory location (0 through 9).
4. Press the memory button again. The display shows
ENTER NAME (up to 15 characters).
NOTE: If you don't want to enter the name, skip step 5.
5. Use the touch-tone pad to enter the name (up to 15
characters).
For example, to enter the name Bill Smith, press the two
key twice for the letter B, press the four key three times
for the letter I, and press the five key three times for the
letter L. After one second, press the five key three times
again for the second letter L and press the one key to
insert a space between the letter L and S. Press the
seven key four times for the letter S, press the six key
once for the letter M, press the four key three times for
the letter I, press the eight key once for the letter T, and
press the four key twice for the letter H.
NOTE: If you enter a wrong letter, press delete/
channel button to backspace.
While talking, press the cid/vol (+/> or -/<) buttons to
adjust the listening level of the handset's earpiece. There
are four volume levels. Press the right arrow (+/>) button to
increase the volume level, and press the left arrow (-/<)
button to decrease. VOL 1 is the lowest level and VOL 4 is
the loudest.
NEW CALL #
Caller ID name
- OR -
3. Use the cid/vol (-/<) arrow or cid/vol (+/>) arrow button
to scroll through the numbers stored in memory until
the desired number is shown.
IMPORTANT: If you make test calls to emergency
numbers stored in memory, remain on the line and
briefly explain the reason for the call to the dispatcher.
Also, it’s a good idea to make these calls in off-peak
hours, such as early morning or late evening.
INSERTING A PAUSE IN THE DIALING
SEQUENCE
When storing information in memory, press the # pause
button twice within one second to insert a delay in the
dialing sequence of a stored telephone number when a
pause is needed to wait for a dial tone (for example after
you dial 9 for an outside line, or to wait for a computer
access tone). PAUSE shows on the display as a “P. “ Each
pause counts as 1 digit in the dialing sequence.
Ni-Cd
Signals an incoming call
• You must reprogram numbers into memory after a
power outage or battery replacement.
Page signal
Low battery warning
Confirmation Tone
Error tone
GENERAL PRODUCT CARE
TROUBLESHOOTING TIPS
To keep your telephone working and looking good, follow
these guidelines:
• Avoid putting the phone near heating appliances and
devices that generate electrical noise (for example,
motors or fluorescent lamps).
• DO NOT expose to direct sunlight or moisture.
CALLER ID SOLUTIONS
• Avoid dropping and other rough treatment to the phone.
No Display
• Clean with a soft cloth.
• Make sure the battery is fully charged and properly
installed and connected. Replace the battery.
• Never use a strong cleaning agent or abrasive powder
because this will damage the finish.
• If you are using electrical power, make sure that the unit
is connected to a non-switched electrical outlet.
Disconnect the unit from the plug and plug it in again.
• Retain the original packaging in case you need to ship
the phone at a later date.
• To receive Caller ID information, you must be
subscribed to Caller ID service from your local
telephone company.
CAUSES OF POOR RECEPTION
Caller ID Error Message
• Foil backing on insulation.
• The unit displays this message if it detects anything
other than valid Caller ID information during the silent
period after the first ring. This message indicates the
presence of noise on the line.
• Heating ducts and other metal construction can shield
radio signals.
• Aluminum siding.
• You’re too close to appliances such as microwaves,
stoves, computers, etc.
3. Press delete/channel again to delete the entry. DELETED
shows in the display.
INCOMPLETE DATA
CHAIN DIALING FROM MEMORY
ENTER NAME
Use this feature to make calls which require a sequence of
numbers such as using a calling card for a frequently
called long distance number. Basically, you dial each part
of the sequence from memory. The following example
shows how you can use chain dialing to make a call
through a long distance service:
The Number For
ENTER TEL NUMBR
DELETE?
Memory Location
Long distance access number
Authorization code
Frequently called long distance number
7
8
9
DELETE ALL?
DELETED
END OF LIST
1. Make sure the phone is ON.
STORING A REDIAL NUMBER
2. Press memory and then press 7.
TIP: Wait for the access tones between pressing the
memory button, or your call might not go through.
BLOCKED NUMBER/
NAME
HANDSET X
NEW
UNKNOWN NAME/
CALLER/NUMBER
REPLACING THE BATTERY
PAGING
The handset runs on a consumerreplaceable battery located inside the
battery pack. If you experience any of the
following problems, you may need to
replace the battery:
BLOCKED CALL
BLOCKED NAME
• Short talk time
CALL BACK
TALK
• Poor sound quality
• Limited range
FORMAT
1
4 ghi
7 pqrs
• In use indicator light fails to light
2 abc
3 def
5 jkl
6 mno
8 tuv
9 wxyz
0
# pause
REPT
exit
*
tone
redial
2. Press the memory button and REPLACE MEMO? shows
in the display.
• Make sure the tone/pulse setting is programmed correctly.
A long warbling tone
(with ringer on)
One short and one long beep
Two beeps every 7 seconds
Two long beeps
Three short beeps
• Base is installed in the basement or lower floor of
the house.
3. Press delete/channel. The display shows DELETE?
1. Repeat steps 1 through 6 in Storing a Name and
Number in Memory.
Meaning
• Check or repeat installation steps:
3. Press *tone/cancel to exit, or press the memory button
to store the number. You will hear a confirmation tone.
To replace an old redial number stored in a memory
locations with a new redial number:
NOTE: The RBRC seal on the battery used in
your CRAFTSMAN product indicates that we
are participating in a program to collect and
recycle Nickel Cadmium batteries throughout
the United States. Please call 1-800-8BATTERY for information or contact your
local recycling center.
• Make sure you follow the proper dialing sequence.
Signal
The following indicators show the status of a message or
of the unit.
2. Use the cid/vol (-/<) arrow or cid/vol (+/>) arrow button
to display the desired Caller ID record.
4. Press delete/channel again to erase all CID records.
You will hear a confirmation tone, and the display
shows NO CALLS.
• Remove batteries if storing over 30 days.
• Make sure memory location keys are correctly
programmed.
2. While the entry is displayed, press delete/channel button
to delete the entry. The display shows DELETE?
4. At the next access tone, press memory and then 9.
2. Use the cid/vol (-/<) arrow or cid/vol (+/>) arrow button
to display any Caller ID record.
• Keep batteries out of the reach of children.
Memory Dialing
• Atmospheric conditions, such as strong storms.
1. Make sure the phone is OFF (not in TALK mode).
1. Make sure the phone is OFF (not in TALK mode).
• To reduce the risk of fire or personal injury, use only the
battery listed in the User’s Guide.
• Replace the battery.
No dial tone
DELETING A CID RECORD
3. Press the memory button to store the number. You will
hear a confirmation tone.
• Do not burn, disassemble, mutilate, or puncture. Like
other batteries of this type, toxic materials could be
released which can cause injury.
• See solutions for “No dial tone.”
TELEPHONE SOLUTIONS
2. Press the memory button and REPLACE MEMO? shows
in the display.
DELETING ALL CID RECORDS
BATTERY SAFETY PRECAUTIONS
• Place handset in remote charger for 20 seconds to reset
the security code. If that doesn’t work, charge battery for
16 hours.
DISPLAY MESSAGES
3. When you hear the access tone, press memory again
and then press 8.
2. Press the redial button.
CAUTION: To reduce the risk of fire or personal
injury, use Sears battery pack 24279, or G.E.
battery pack TL26506 or TL96506.
HANDSET SOUND SIGNALS
Unit beeps
1. Press memory, then use the cid/vol (-/<) arrow or cid/vol
(+/>) arrow button to view the entry.
1. Repeat steps 1 through 6 in Storing a Name and
Number in Memory.
1. Repeat steps 1 through 6 in Storing a Name and
Number in Memory.
7. Place handset in the remote charger to charge. Allow
the handset battery to properly charge (for 16 hours)
prior to first use or when you install a new battery. If
you do not properly charge the phone, battery
performance is compromised.
REVIEWING AND DELETING STORED
NUMBERS
CHANGING A STORED NUMBER
4. Press delete/channel again to erase the record showing
in the display. You will hear a confirmation tone. The
display shows DELETED and the next Caller CID record
shows in the display.
Replacement batteries are available at your local Sears
store, item no. 24279.
4. Press CALLBACK/TALK. The numbers dial automatically.
3. Press *tone/exit to exit, or press memory again and the
new CID record replaces the old CID record in that
memory location. You will hear a confirmation tone.
3. Press and hold channel/delete button until the unit
beeps and DELETE ALL? shows in the display.
Caller ID phone number
3. Press the number (0-9) for the desired memory location.
The number dials automatically.
2. Press memory button.
8. Press memory again to store the number. You will hear a
confirmation tone.
New call
6. Put the battery pack cover back on, and
snap the battery pack onto the bottom of
the handset.
long distance code “1” + 3-digit area code +
7-digit telephone number.
2. Press the memory button and REPLACE MEMO? shows
in the display.
Date
2. Press memory button.
Indicates registration is in process,
and you should wait until you hear
a confirmation tone.
11-digit
1. Repeat steps 1 through 2.
Time
REGISTERING...
WAIT FOR BEEP
1. Make sure the phone is OFF (not in TALK mode).
VOLUME
Caller ID (CID) is a service available from your local
telephone company. For Caller ID to work on this system,
you must subscribe to Caller ID service from your local
telephone company.
5. Insert the new battery and connect the
cord into the jack inside the handset.
3-digit area code + 7-digit telephone number.
7. Use the number keypad to enter the telephone number
you want to store (up to 24 digits).
CALLER (CID) FEATURES
1. Make sure the phone is ON by pressing the CALLBACK/
TALK button.
10-digit
To replace a CID record stored in a memory location with
a new CID record:
While you are talking on the phone, the total talk time is
displayed on the bottom line of the display.
Prompt telling you to move the
handset near the base and press
and hold the base page button.
7-digit telephone number.
6. Press the memory button to save the name. The display
shows ENTER TEL NUMBR.
CALL TIMER
PRESS AND HOLD
BASE PAGE KEY
7-digit
3. Press the desired memory location. You will hear a
confirmation tone. Example, press the number 1 key to
store the record in memory location 1.
NOTE: If you turn the ringer off, the display shows
RINGER = OFF when the phone is in standby mode.
DIALING A STORED NUMBER
4. Disconnect the battery plug from the jack
in the handset battery pack compartment
and remove the battery.
3. Remove the battery pack cover.
RC
REVIEWING CID RECORDS
2. Use the cid/vol (-/<) arrow or cid/vol (+/>) arrow button
to display the desired Caller ID record.
Indicates a message is available.
Prompt telling you to register the
handset to the base.
RB
Press the *tone/exit button to cancel any command you
initiated.
1. Make sure the phone is OFF (not in TALK mode).
2. Use a screw driver to loosen the screws
on the battery pack cover.
MESSAGE WAITING
PRESS AND HOLD
FORMAT KEY
3. Press *tone/exit to exit, or press the memory button
again and the new redial number replaces the old redial
number in that memory location. You will hear a
confirmation tone.
C
DIALING A CID NUMBER
RBR
This unit receives and displays CID information
transmitted by your local telephone company. This
information can include the phone number, date, and
time; or the name, phone number, date, and time. The unit
stores up to 40 calls for later review.
IN USE INDICATOR LIGHT
delete/channel
oper
ringer
memory
program/flash
Make sure the telephone is OFF before
you replace the battery.
NO DATA
EMPTY
1. Push in on the tabs on the battery
pack to detach it from the handset.
NO CALLS
CID information is interrupted
during transmission or the phone
line is excessively noisy.
Prompt telling you to enter the
name for one of the 10 memory
locations.
Prompt telling you to enter the
telephone number for one of the
10 memory locations.
Prompt asking if you want to erase
CID records or one of the 10
numbers stored in the phone’s
outgoing memory.
Prompt asking if you want to erase
all CID records.
Prompt confirming the CID/
Memory record is erased.
Indicates that there is no
additional information in CID
memory.
Indicates the caller's name and
number is blocked from transmission.
Indicates the handset is in use
Indicates call or calls have not
been reviewed.
The incoming call is from
an area not serviced by CID or the
information was not sent.
Someone has pressed the page
button on the base.
The person is calling from a
number that has been blocked
from transmission.
The person’s name is blocked
from transmission.
Repeat call message. Indicates that
a new call from the same number
was received more than once.
No CID information was received.
Indicates a memory location is
vacant.
Indicates no CID records have
been stored.
Make sure the base is plugged into a working outlet.
• Base is plugged into an AC outlet with other
electronic devices.
Make sure the telephone line cord is connected to the
base and the wall jack.
• Baby monitor is using the same frequency.
• Disconnect the base from the wall jack and connect
another phone to the same jack. If there is no dial tone
in the second phone, the problem might be your wiring
or local service.
• The handset may be out of range of the base. Move
closer to the base.
• Handset battery is low.
• You’re out of range of the base.
INTERFERENCE INFORMATION
• Make sure the battery pack installed correctly.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference; and (2) This device must accept any
interference received, including interference that may cause
undesired operation.
• Did the handset beep when you pressed the CALL
BACK/TALK button? Did the display indicator turn on?
The battery may need to be charged.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
• The handset may lose registration with the base unit;
follow the handset registration steps to re-register it to
the base unit.
This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation.
• Make sure the battery is properly charged (16 hours).
Dial tone is OK, but can't dial out
• Make sure the tone/pulse setting is programmed correctly.
Handset does not ring
• Make sure the ringer switch on the handset is
turned ON. Press the RINGER button to check your
current setting.
• You may have too many extension phones on your line.
Try unplugging some phones.
• See solutions for “No dial tone.”
Handset Loses Registration ID
• The handset prompts you to re-register the handset to
the base to restore the registration ID.
You experience static, noise, or fading in and out
• Change channels
• Handset may be out of range of the base. Move closer
to the base.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna (that is, the antenna
for radio or television that is “receiving” the interference).
• Reorient or relocate and increase the separation between the
telecommunications equipment and receiving antenna.
• Connect the telecommunications equipment into an outlet on a
circuit different from that to which the receiving antenna is
connected.
• Consult the dealer or an experienced radio/TV technician for
help.
If these measures do not eliminate the interference, please consult
your dealer or an experienced radio/television technician for
additional suggestions. Also, the Federal Communications
Commission has prepared a helpful booklet, “How To Identify and
Resolve Radio/TV Interference Problems.” This booklet is available
from the U.S. Government Printing Office, Washington, D.C. 20402.
Please specify stock number 004-000-00345-4 when ordering copies.
• Relocate the base.
• Charge the battery.
• Make sure base is not plugged into an outlet with
another household appliance.
Sears, Roebuck and Co., Dept. 817WA,
Hoffman Estates, IL 60179 Dept.
Model 27413
16278350
Printed in China
Download PDF

advertising