Craftsman | 315.27127 | User's Manual | Craftsman 315.27127 User's Manual

Owner's Manual
iPR
0 FES
S I 0 HAL
i
112 in. PROFESSIONAL
CORDLESS HAMMER DRILL
Variable Speed / Reversible
Model No.
315.271270
Save this manual
future reference
_,
for
•
•
•
•
•
•
CAUTION:
Read and
follow all Safety Rules and
Operating Instructions before
first use of this product.
Customer
Help
Line:
1-800-932-3188
Sears, Roebuck
and Co., Hoffman
Estates,
IL 60179
Visit the Craftsman web page: www.sears.com/craftsman
972000-717
1-00
USA
Safety
Features
Assembly
Operation
Maintenance
Parts List
®
TABLE
OF CONTENTS
•
General Safety Rules .................................................................................................................................................
2-3
•
Specific Safety Rules/Symbols
3-5
•
Features .....................................................................................................................................................................
5-8
•
Assembly ..................................................................................................................................................................
9-10
•
Operation ................................................................................................................................................................
•
Maintenance ................................................................................................................................................................
•
Accessories
•
Exploded View And Repair Parts List .........................................................................................................................
19
•
Parts Ordering / Service ..............................................................................................................................................
20
..................................................................................................................................
..........................................................................................................................................
WARNING:
Read and understand all instructions.
Failure to follow all instructions listed below, may
result in electric shock, fire and/or serious personal
injury.
SAVE THESE
Personal
•
Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases, or dust. Power tools create sparks
which may ignite the dust or fumes.
•
Keep bystanders, children, and visitors away while
operating a power tool. Distractions can cause you
to lose control.
Electrical
•
•
A battery operated tool with integral batteries or a
separate battery pack must be recharged only with
the specified charger for the battery. A charger that
may be suitable for one type of battery may create a
risk of fire when used with another battery. Use battery
only with charger listed.
MODEL
BATTERY PACK
CHARGER
315.271270
•
Item No. 9_-11034
Item No. 9_-11040
Use battery operated tool only with specifically
designated battery pack. Use of any other batteries
may create a risk of fire. Use only with battery pack
listed.
Safety
•
Dress properly. Do not wear loose clothing or
jewelry. Contain long hair. Keep your hair, clothing,
and gloves away from moving parts. Loose clothes,
jewelry, or long hair can be caught in moving pads.
•
Avoid accidental starting. Be sure switch is in the
locked or off position before inserting battery
pack. Carrying tools with your finger on the switch or
inserting the battery pack into a tool with the switch on,
invites accidents.
•
Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached
to a rotating part of the tool may result in personal
injury.
•
Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enable
better control of the tool in unexpected situations.
•
Use safety equipment. Always wear eye protection.
Dust mask, non-skid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions.
Safety
Do not abuse the cord. Never use the cord to carry
the charger. Keep cord away from heat, oil, sharp
edges, or moving parts. Replace damaged cords
immediately. Damaged cords may create a fire.
:...................... 18
Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use tool while tired or under the influence of
drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious
personal injury.
Work Area
Keep your work area clean and well lit. Cluttered
benches and dark areas invite accidents.
17
•
INSTRUCTIONS
•
11-16
Tool Use and Care
•
Use clamps or other practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body is unstable and
may lead to loss of control.
•
Do not force tool. Use the correct tool for your
application. The correct tool will do the job better and
safer at the rate for which'it is designed.
Do not use tool if switch does not turn it on or off.
A tool that cannot be controlled with the switch is
dangerous and must be repaired.
•
•
•
Disconnect battery pack from tool or place the switch
in the locked or off position before making any adjustments, changing accessories, or storing the tool. Such
•
When
other
nails,
make
Maintain tools with care. Keep cutting tools sharp
and clean. Properly maintained tools, with sharp
cutting edges are less likely to bind and are easier to
control.
•
Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
affect the tool's operation. If damaged, have the tool
serviced before using. Many accidents are caused by
poorly maintained tools.
•
Use only accessories that are recommended by
the manufacturer for your model. Accessories that
may be suitable for one tool, may create a risk of injury
when used on another tool.
Service
preventive safety measures reduce risk of starting the tool
accidentally.
Store idle tools out of reach of children and other
untrained persons.
of untrained users.
•
•
Tool service must be performed only by qualified
repair personnel. Service or maintenance performed
by unqualified personnel could result in a risk of injury.
•
When servicing a tool, use only identical replacement parts. Follow instructions
in the Maintenance
section of this manual. Use of unauthorized parts or
failure to follow Maintenance Instructions may create a
risk of shock or injury.
Tools are dangerous in the hands
battery pack is not in use, keep it away from
metal objects like: paper clips, coins, keys,
screws, or other small metal objects that can
a connection from one terminal to another.
Shorting the battery terminals together may cause
sparks, burns, or a fire.
Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact
hidden wiring. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator.
Additional
•
•
Rules For Safe Operation
ing accessories. Following this rule will reduce the
risk of electric shock, fire, or serious personal injury.
Know your power tool. Read operator's manual
carefully. Learn its applications and limitations, as
well as the specific potential hazards related to
this tool. Following this rule will reduce the risk of
electric shock, fire, or serious injury.
Make sure your extension cord is in good condition. When using an extension cord, be sure to
use one heavy enough to carry the current your
product will draw. A wire gage size (A.W.G.) of at
least 16 is recommended for an extension cord
100 feet or less in length. A cord exceeding 100
feet is not recommended. If in doubt, use the next
heavier gage. The smaller the gage number, the
heavier the cord. An undersized cord will cause a
drop in line voltage resulting in loss of power and
overheating.
Important
•
Rules for Battery Tools
Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in
operating condition. Be aware of possible hazards
when not using your battery tool or when chang3
•
Do not place battery tools or their batteries near
fire or heat. They may explode. Following this rule
will reduce the risk of electric shock, fire, or serious
personal injury.
•
Do not charge battery tool in a damp or wet
location. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
•
Your battery tool should be charged in a location
where the temperature is more than 50°F but less
than 100°F. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
•
Under extreme usage or temperature conditions,
battery leakage may occur. If liquid comes in
contact with your skin, wash immediately with
soap and water, then neutralize with lemon juice
or vinegar. If liquid gets into your eyes, flush them
with clean water for at least 10 minutes, then seek
immediate medical attention. Following this rule will
reduce the risk of serious personal injury.
c. That wire size is large enough forAC ampere
rating of charger as specified below:
Important Safety Instructions For Charger
•
•
Save these instructions. This manual contains
important safety and operating instructions for
battery charger part number 9-11040, Following this
rule will reduce the risk of electric shock, fire, or
serious personal injury.
To reduce risk of injury, charge only nickelcadmium and nickel metal hydride type rechargeable batteries. Other types of batteries may burst
causing personal injury and damage. Following this
rule will reduce the risk of electric shock, fire, or
Cord Size (AWG)
16
16
16
•
Do not operate charger with a damaged i:ord or
plug. If damaged, have replaced immediately by a
qualified serviceman. Following this rule will reduce
the risk of electric shock, fire, or serious personal
injury.
•
Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in any
way; take it to a qualified serviceman. Following
this rule will reduce the risk of electric shock, fire, or
serious personal injury.
•
To reduce the risk of electric shock, unplug
charger from outlet before attempting any maintenance or cleaning. Turning off controls will not
reduce this risk. Following this rule will reduce the
risk of electric shock, fire, or serious personal injury.
•
Do not use charger outdoors. Following this rule will
reduce the risk of electric shock, fire, or serious
personal injury.
•
stepped on, tripped over, or otherwise subjected
to damage or stress. Following this rule will reduce
the risk of serious personal injury.
Disconnect charger from power supply when not
in use. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
,_
An extension cord should not be used unless
absolutely necessary, Use of improper extension
cord could result in a risk of fire and electric shock. If
extension cord must be used, make sure:
DANGER: RISK OF ELECTRIC SHOCK. DO NOT
TOUCH UNINSULATED PORTION OF OUTPUT
CONNECTOR OR UNINSULATED BATTERY TERMINAL.
•
Save these instructions. Refer to them frequently
and use them to instruct others who may use this
tool. If you loan someone this tool, loan them
these instructions also. Following this rule will
reduce the risk of electric shock, fire, or serious
personal injury.
Do not expose charger to rain or snow. Following
this rule will reduce the risk of electric shock, fire, or
serious personal injury.
•
Use of an attachment not recommended or sold
by the battery charger manufacturer may result in
a risk of fire, electric shock, or injury to persons.
Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.
III
100'
Do not disassemble charger; take it to a qualified
serviceman when service or repair is required.
Incorrect reassembly may result in a risk of
electric shock or fire. Following this rule will reduce
the risk of electric shock, fire, or serious personal
injury.
•
•
50'
•
serious personal injury.
•
25'
Note: AWG = American Wire Gage
Before using battery charger, read all instructions
- and cautionary markings in this manual, on
battery charger, and product using battery
charger. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
•
Cord Length (Feet)
To reduce risk of damage to charger body and
cord, pull by charger plug rather than cord when
disconnecting charger. Following this rule will
reduce the risk of electric shock, fire, or serious
personal injury.
Make sure cord is located so that it will not be
a. That pins on plug of extension cord are the
same number, size and shape as those of
plug on charger.
b. That extension cord is properly wired and in
good electrical condition; and
4
SYMBOLS
SYMBOL
NAME
DESIGNATION/EXPLANATION
V
Volts
Voltage
A
Amperes
Current
Hz
Hertz
Frequency (cycles per second)
min
Minutes
Time
Alternating Current
Type or a charact'eristic of current
--=-
Direct Current
Type or a characteristic
no
No Load Speed
Rotational speed, at no load
.../min
Revolutions or Reciprocation
_.
Safety Alert Symbol
Per Minute
of current
Revolutions, strokes,
surface speed, orbits etc. per minute
Indicates danger, warning or caution.
It means attention!!! Your safety is
involved.
DEFINITIONS
A)
DANGER: Failure to obey a safety warning will result in serious injury to yourself or to others,
Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury,
B)
WARNING: Failure to obey a safety warning can result in serious injury to yourself or to others,
Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.
C)
CAUTION: Failure to obey a safety warning may result in property damage or personal injury
to yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric
shock and personal injury.
D)
NOTE: Advises you of information or instructions vital to the operation or maintenance of the
equipment.
5
KNOW YOUR
HAMMER
BIT STORAGE
DRILL
See Figure 1.
Before attempting to use your hammer drill, familiarize
yourself with all operating features and safety
requirements.
,_
WARNING: Carefully read through this entire owner's
manual before using your new hammer drill. Pay close •
attention to the Rules For Safe Operation, Warnings
and Cautions. If you use your hammer drill properly and
only for what it is intended, you will enjoy years of safe,
reliable service.
When not in use, bits provided with your hammer drill can
be placed in the storage area located on the top of the
motor housing.
LEVEL
To keep drill bit level during drilling operations, a level is
located on the top and end of the motor housing.
AUXILIARY
An auxiliary handle is packed with your hammer drill for
ease of operation and to help prevent loss of control.
DEPTH
_L
WARNING: Do not allow fam)liarity with your hammer
drill to make you careless. Remember that a careless
fraction of a second is sufficient to inflict severe injury.
CHUCK
Your hammer drillhas a keyless chuck that allows you to
hand tighten or release drill bit in the chuck jaws.
GAGE
ROD
A depth gage rod has been packed with your hammer drill
to assist you in controlling the depth of drilled holes.
_1,
KEYLESS
HANDLE
WARNING: If any parts are missing, do not operate
your hammer drill until the missing parts are replaced.
Failure to do so could result in possible serious
personal injury.
SWITCH
PRODUCT
SPECIFICATIONS:
To turn your hammer drill ON, depress tile switch trigger.
Release switch trigger to turn your hammer drill OFF.
SWITCH
LOCK
The switch trigger can be locked in the OFF position. This
feature helps reduce the possibility of accidental starting
tool when not in use.
VARIABLE
SPEED
GEAR TRAIN
(DIRECTION
1/2 in. Keyless
Motor
DC Motor 18 Volt
Gear Train
Two Speed
OF ROTATION SELECTOR)
Your hammer drill has a forward/reverse
Variable Speed
No Load Speed
selector located
0-400 RPM (Low)
0-1400 RPM (High)
0-6,400 (Low)
0-22,400 (High)
Clutch
24 Positions
Maximum Torque
SELECTOR
315.271270
Chuck
Hammer Speed
Your hammer drill has a two speed gear train designed for
drilling or driving at HI or LO speeds. A slide switch is
located on top of your drill to select either HI or LO speed.
FORWARD/REVERSE
DRILL
Switch
This tool has a variable speed switch that delivers higher
speed with increased trigger pressure. Speed is controlled
by the amount of switch trigger depression.
TWO SPEED
HAMMER
500 in./Ibs.
CHARGER
ITEM NO. 9-11040
Input
120 V, 60 Hz, AC only
above the switch trigger.
WRIST
STRAP
A wrist strap is provided to reduce the chances of dropping
your hammer drill. Place one hand through the wrist strap
when carrying tool.
Charging Voltage
Charge Rate
BATTERY
PACK
9.6 - 24 Volt
1 Hour
ITEM NO. 9-11034
TWO
SPEED
GEAR
TRAIN
(HI-LO)
AUXILIARY
HANDLE
LEVEL
WiNG
SCREW
BIT
STORAGE
AREA
DEPTH
GAGEROD
DIRECTIONOF
ROTATIONSELECTOR
(FORWARD/REVERSE)
KEYLESS
CHUCK
MODE
SELECTOR
• TORQUE
ADJUSTMENT
RING
TRIGGER
BATTERY
PACK
WRISTSTRAP
Fig.1
7
LED FUNCTIONOF CHARGER
YELLOW
LIGHT
"ON" AND RED
LIGHTFLASHINGINDICATES
DEFECTIVEBATTERYPACK
CHARGER
\
CHARGER
FASTCHARGINGMODE
BATTERYPACKSHOWN
IN CHARGER
GREENLIGHT"ON" INDICATESFULLY
CHARGEDANDSLOWCHARGING
TO MAINTAINBATTERYPACK
Fig,2
CHARGER
See Figure 3,
Your charger has a "key hole" hanging feature for
convenient, space saving storage. Screws should be
installed so that center distances are 4-1/8 inches apart.
4-1/8in.
BACKSIDEOF CHARGER
Fig. 3
8
AUXILIARY
HANDLE
•
Lock the switch trigger by placing the direction of
rotation selector in center position. See Figure 13.
An auxiliary handle is packed with your drill for ease of
operation and to help prevent loss of control. The handle
can be rotated 360 ° and it can also be mounted on
•
Align raised ribs on battery pack with grooves on
bottom of drill, then attach battery pack to drill as
shown in Figure 5.
opposite side for left hand use.
•
Make sure latch on battery pack snaps in place and
battery pack is secured to drill before beginning
operation.
See Figure 4.
Note: For convenience and ease of starting threads, the
hex nut has been trapped inside the mblded slot in the
auxiliary handle.
TO INSTALL:
•
RAISEDRIBS
Lock the switch trigger by placing the direction of
rotation selector in center position. See Figure 13.
•
Loosen wing screw enough to make ring of handle
large enough to fit over chuck.
•
Place ring of handle over the chuck and mode selector. Note: Handle fits in a groove behind torque
adjusting ring.
•
Rotate handle to desired angle.
•
Tighten wing screw securely.
Note: If wing screw and wear plate is removed from
auxiliary handle, when reassembling, the markings on
the wear plate must be positioned as shown in Figure
4. This prevents the depth gage rod from slipping.
See Figure 4.
LATCH
BATTERYPACK
CAUTION:
When attaching battery pack to your
drill, be sure raised ribs and grooves align properly
and latch snaps in place properly. Improper assembly
can cause damage to drill and battery pack.
WINGSCREW
TO
TORUE
KEYLESS ADJUSTING
CHUCK
RING GROOVE
TIGHTEN
Fig, 5
TO REMOVE
TO
LOOSEN
BATTERY
PACK FROM
DRILL
See Figure 6.
•
Lock the switch trigger by placing the direction of
rotation selector in center position. See Figure 13.
•
Depress latch located on front of battery pack (1) to
release battery pack.
•
Pull forward on battery pack (2) to remove from drill.
MODE
DEPRESSLATCHTO
RELEASEBATTERYPACK
360_o SELECTOR
ROTATION
RAISEDRIB
AUXILIARY
HANDLE
MARKINGSON
BACKSIDE
OF WEARPLATE
Fig. 4
To prevent possible loss of control, auxiliary handle
should be checked periodically for tightness. Do not
operate hammer drill with auxiliary handle loose.
TO ATTACH
BATTERY
PULL
FORWARD
TO REMOVE
PACK TO DRILL
See Figure 5.
Note: Battery pack is shipped in a low charge condition.
Therefore, it must be charged prior to use. Refer to page 11,
"CHARGING BATTERY PACK" for charging instructions.
BATTERYPACK
9
Fig. 6
INSTALLING
BITS
REMOVING
BITS
See Figure 7.
See Figure Z
•
Lock the switch trigger by placing the direction of
rotation selector in center position. See Figure 13.
•
Lock the switch trigger by placing the direction of
rotation selector in center position. See Figure 13.
•
Open or close chuck jaws to a point where the opening is slightly larger than the bit size you intend to use.
Also, raise the front of your drill slightly to keep the bit
from f;_lling out of the chuck jaws.
•
Loosen the chuck jaws from drill bit.
•
To loosen, grasp and hold the drill with one hand,
while rotating chuck sleeve with your other hand.
Note: Rotate chuck sleeve in the direction of the arrow
marked UNLOCK to loosen the chuck jaws.
•
Do not use a wrench to tighten or loosen the chuck
jaws.
•
Remove drill bit from chuck jaws.
•
Insert drill bit into chuck the full length of the jaws as
shown in Figure 7.
CHUCKJAWS
USING DEPTH
See Figure 9.
GAGE
ROD
A depth gage rod has been packed with your hammer drill
to assist you in controlling the depth of drilled holes.
•
Loosen wing screw on auxiliary handle.
•
Orient depth gage rod so that markings on depth gage
rod face markings on wear plate. See Figure 4. Insert
depth gage rod through hole on auxiliary handle.
Adjust depth gage rod so that the drill bit extends
beyond the end of the. rod to the required drilling
depth.
DRILLBIT
LOCK
•
CHUCKSLEEVE
RIGHT
•
•
Fig. 7
Tighten the chuck jaws on drill bit. To tighten, grasp
and hold the drill with one hand, while rotating the
chuck sleeve with your other hand.
Tighten wing screw securely. This secures depth
gage rod at desired depth of cut. It also secures
auxiliary handle.
WING
SCREW
Note: Rotate the chuck sleeve in the direction of the
arrow marked LOCK to tighten chuck jaws.
•
Do not use a wrench to tighten or loosen the chuck
jaws.
,_
WARNING:
Do not insert drill bit into chuck jaws
and tighten as shown in Figure 8. This could cause
drill bit to be thrown from drill resulting in possible
serious personal injury or damage to the chuck.
WEAR
PLATE
DRILLBIT
TO
DEPTH
DRILLING
DEPTH
DRILLING
DEPTH
MARKINGSON
DEPTHGAGEROD
AUXILIARY
HANDLE
Fig. 9
When drilling holes with the depth gage rod installed, the
desired hole depth has been reached when the end of the
rod comes in contact with the surface of the material
being drilled.
Fig. 8
10
_, WARNING:Alwayswearsafetygogglesor safety
glasseswithsideshieldswhenoperatingtools.
Failureto dosocouldresultin objectsbeingthrown
intoyoureyes,resultingin possibleseriousinjury.
If after one hour red light is still flashing, this indicates a
defective battery pack and should be replaced.
CHARGINGBATTERYPACK
Thebatterypackforthistoolhasbeenshippedin a low
chargeconditionto preventpossibleproblems.Therefore,
youshouldchargeit untillightonfrontof chargerchanges
fromredtogreen.
Note:Batteries
will notreachfullchargethefirsttimethey
arecharged.Allowseveralcycles(drillingfollowedby
recharging)
forthemtobecomefullycharged.
TO CHARGE
Yellow light on and red light flashing indicates defective
battery pack. Return battery pack to your nearest Sears
Repair Center for checking or replacing.
•
Charge battery pack only with the charger provided.
•
Make sure power supply is normal house voltage,
120 volts, 60 Hz, AC only.
•
Connect charger to power supply.
•
Attach battery pack to charger by aligning raised ribs
on battery pack with grooves in charger, then slide
battery back onto charger. See Figure 10.
Green light on indicates battery pack is fully charged
and slow charging to maintain battery pack.
•
When your battery pack becomes fully charged, the red light
will tum OFF and the green light will tum ON,
•
After normal usage, 1 hour of charging time is required to be
fully charged. A minimum charge time of 1-1/2 hours is
required to recharge a completely discharged tool.
•
The battery pack will become slightly warm to the touch while
charging. This is normal and does not indicate a problem.
•
Do not place charger in an area of extreme heat or
cold. It will work best at normal room temperature.
•
When the batteries become fully charged, unplug your
charger from power supply and remove the battery
pack.
LED FUNCTION
LED WILL BE LIGHTED TO INDICATE STATUS OF
CHARGER AND BATTERY PACK:
BATTERY
PACK
TO
REMOVE
•
Red LED Lighted = Fast Charging Mode.
•
Green LED Lighted = Fully Charged And Slow
Charging To Maintain Battery Pack.
•
Red LED Flashing = Hot Or Deeply Discharged
Battery Pack. Also Defective Battery Pack After 1
Hour.
•
Yellow LED Lighted and Red LED Flashing =
Defective Battery Pack.
CHARGER
IMPORTANT
INFORMATION
HOT BATTERIES
TO
ATTACH
FOR
RECHARGING
Under extreme continuous use, the batteries in your
battery pack will become hot. You should let a hot battery
pack cool down for approximately 1 hour before attempting to recharge. When the battery pack becomes discharged and is hot, this will cause the red light on your
battery charger to flash. When battery pack cools down,
red light will glow continuously indicating fast charging
mode, 1 hour charge time. Once the battery pack cools
down, it will recharge battery pack in fast charging mode
as normal.
GROOVES
Fig, 10
•
OF CHARGER
Red light should turn on. Red light indicates fast
charging mode.
Note: This situation only occurs when extreme continuous
use of your drill causes the batteries to become hot. It
does not occur under normal circumstances. Refer to
"CHARGING BATTERY PACK" for normal recharging of
batteries. If the charger does not charge your battery pack
under normal circumstances, return both the battery pack
and charger to your nearest Sears repair center for
electrical check.
If red light is flashing, this indicates battery pack is
deeply discharged or hot.
If battery pack is hot, red light should become steady
after battery pack has cooled down.
If battery pack is deeply discharged, red light should
become steady after voltage has increased, normally
within 60 minutes.
11
SWITCH
SWITCH
LOCK
See Figure 11.
See Figure 13.
To turn your drill ON, depress the switch trigger. To turn it
OFF, release the switch trigger.
The switch trigger can be locked in the OFF position. This
feature can be used to prevent the possibility of accidental
starting when not in use. To lock switch trigger, place the
direction of rotation selector in center position.
FORWAR_REVERSE
SELECTOR
SELECTOR
CENTERPOSITION
(LOCK)
CENTERPOSITION
,,OCK
TRIGGER
VARIABLE
Fig, 11
_,._REVERSE
-_
Fig. 13
SPEED
This tool has a variable speed switch that delivers higher
speed and torque with increased trigger pressure, Speed
is controlled by the amount of switch trigger depression,
Note: You might hear a whistling or ringing noise from the
switch during use. Do not be concerned, this is a normal
part of the switch function.
TWO SPEED
GEAR TRAIN
See Figure 12.
Your drill has a two-speed gear train designed for drilling
or driving at LO (1) or HI (2) speeds. A slide switch is
located on top of your drill to select either LO (1) or HI (2)
speed, When using drill in the LO (1) speed range, speed
will decrease and unit will have more power and torque.
When using drill in the HI (2) speed range, speed will
increase and unit will have less power and torque, Use
LO (1) speed for high power and torque applications and
HI (2) speed for fast drilling or driving applications.
TWOSPEED
GEARTRAIN(HI-LO)
LO
\
SPEED
,_
WARNING:
Battery tools are always in operating
condition. Therefore, switch should always be locked
when not in use or carrying at your side.
REVERSIBLE
See Figure 13.
This tool has the feature of being reversible. The direction
of rotation is controlled by a selector located above the
switch trigger. With the drill held in normal operating
position, the direction of rotation selector should be
positioned to the left of the switch for drilling. The drilling
direction is reversed when the selector is to the right of
the switch. When the selector is in center position, the
switch trigger is locked.
,_
CAUTION:
To prevent gear damage, always allow
chuck to come to a complete stop before changing
the direction of rotation or the two speed gear train
(hi-lo).
To stop, release switch trigger and allow the chuck to
come to a complete stop.
HI
SPEED
Fig. 12
12
KEYLESS
CHUCK
TO DECREASE ADJUSTINGRING
TORQUE
See Figure 14.
A keyless chuck has been provided with your drill to allow
for easy installation and removal of bits. As the name
implies, you can hand tighten or release drill bits in the
chuck jaws. Arrows on the chuck indicate which direction
to rotate the chuck sleeve in order to LOCK (tighten) or
UNLOCK (release) the chuck jaws. Loosen the chuck
sleeve by rotating it counterclockwise with one hand.
Insert drill bit into the chuck the full length of the jaws,
tighten securely by rotating the chuck sleeve in clockwise
direction.
CHUCKJAWS
TOINCREASE
TORQUE
UNLOCK
Fig. 15
Note: Remember the two-speed feature (HI-LO) when
setting torque. The amount of torque will vary depending
on which speed setting you have your drill. Switching to
LO speed will increase torque. Switching to HI speed will
decrease torque,
BIT STORAGE
See Figure 16.
DRILLBIT
LOCK
(Tighten)
When not in use, bits provided with your drill can be
placed in the storage area located on the top of your drill
as shown in Figure 16.
CHUCKSLEEVE
RIGHT
BIT
STORAGEAREA
Fig. 14
WARNING:
Do not hold chuck sleeve with one hand
and use power of the drill to tighten chuck jaws on
drill bit. Chuck sleeve could slip in your hand or your
hand could slip and come in contact with rotating drill
bit. This could cause an accident resulting in serious
personal injury.
ADJUSTABLE
TORQUE
SCREWDRIVER
BIT
SCREWDRIVER
BIT
CLUTCH
Your drill is equipped with an adjustable torque clutch for
driving different types of screws into different materials.
The proper setting depends on the type of material and
the size of screw you are using.
TO ADJUST
•
•
Fig. 16
TORQUE
Identify the twenty four torque indicator settings
located on the front of your drill. See Figure 15.
Rotate adjusting ring to the desired setting.
1 - 4
For driving small screws.
•
5 - 8
For driving screws into soft
material.
•
9 - 12
For driving screws into soft and
hard materials.
• 13 - 16
For driving screws in hard wood.
• 17 - 20
For driving large screws.
• 21 - 4111
For heavy drilling.
13
DRILLING
APPLICATIONS
See Figure 18.
(Use only for the purposes listed below)
END VIEW
•
Hammer drilling in concrete and masonry.
•
Drilling in wood.
•
Drilling in ceramics, plastics, fiberglass, and laminates.
•
Drilling in both hard and soft metals.
•
Using driving accessories, such as driving screws
with screwdriver bits.
LEVEL
LEVEL
DRILLING
See Figure 17.
A convenient feature provided on your drill is a level. It is
recessed in the motor housing on top and end of your
drill. It can be used to keep drill bits level during most
drilling operations.
TOP VIEW
Fig. 18
LEVEL
When drilling hard smooth surfaces use a center punch to
mark desired hole location. This will prevent the drill bit
from slipping off center as the hole is started. However,
the low speed feature allows starting holes without center
punching if desired. To accomplish this, simply operate
your drill at a low speed until the hole is started.
The material to be drilled should be secured in a vise or
with clamps to keep it from turning as the drill bit rotates.
Hold tool firmly and place the bit at the point to be drilled.
Depress the switch trigger to start tool.
Move the drill bit into the workpiece applying only enough
pressure to keep the bit cutting. Do not force or apply side
pressure to elongate a hole.
A
Fig. 17
WARNING:
Be prepared for binding or bit
breakthrough. When these situations occur, drill has
a tendency to grab and kick opposite to the direction
of rotation and could cause loss of control when
breaking through material, if not prepared, this loss
of control can result in possible serious injury.
When drilling metals, use a light oil on the drill bit to keep
it from overheating. The oil will prolong the life of the bit
and increase the drilling action.
If the bit jams in workpiece or if the drill stalls, release
switch trigger immediately. Remove the bit from the
workpiece and determine the reason for jamming.
14
TO ADJUST
DRILLING
OR HAMMER
MODE
WOOD
DRILLING
See Figure 19.
To adjust drill to drilling or hammer operation, rotate mode
•
For maximum performance, use high speed steel bits
for wood drilling.
selector in the direction of arrows as shown in Figure 19.
For your convenience a hammer symbol and drill bit
symbol have been molded into the selector.
•
Turn mode selector ring on hammer drill to normal
drilling action.
_
Begin drilling at a very low speed to prevent the bit
from slipping off the starting point. Increase the speed
as the drill bit bites into the material.
WARNING:
Your hammer drill has not been
designed for reverse hammering. Reverse
hammering may damage your drill.
When drilling through holes, place a block of wood
behind the workpiece to prevent ragged or splintered
edges on the back side of the hole.
Do not lock the trigger on for jobs where your
hammer drill may need to be stopped suddenly.
MODE
SELECTOR
METAL
DRILLING
For maximum performance, use high speed steel bits
for metal or steel drilling.
Turn mode selector on hammer driU to normal drilling
action.
Begin drilling at a very low speed to prevent the bit
from slipping off the starting point.
Maintain a speed and pressure which allows cutting
without overheating the bit. Applying too much
pressure will:
Fig. 19
We recommend that you use carbide-tipped bits and
select hammer mode when drilling in hard materials such
as brick, tile, concrete, etc.
•
Overheat the drill;
•
•
Wear the bearings;
Bend or burn bits; and
•
Produce off-center or irregular shaped holes.
When drilling large holes in metal, we recommend that
you drill with a small bit at first, then finish with a larger
bit. Also, lubricate the bit with oil to improve drilling
action and increase bit life.
We recommend that you select normal drilling mode when
drilling with twist drills, hole saws, etc. in steel and soft
materials.
MASONRY
DRILLING
•
For maximum performance use carbide-tipped
masonry impact bits when drilling holes in
brick, tile, concrete, etc.
•
Turn mode selector on hammer drill to
hammer mode. Rotate torque selector to drill position.
15
•
Apply light pressure and medium speed for best
results in brick.
•
Apply additional pressure and high speed for hard
materials such as concrete.
•
When drilling holes in tile, practice on a scrap
piece to determine the best speed and pressure.
CHUCKREMOVAL
Insert hex key wrench in chuck and tighten chuck
jaws securely. Tap sharply with a mallet in a counterclockwise direction. This will loosen chuck on the
spindle. It can now be unscrewed by hand.
See Figure 22.
See Figures 20, 21, and22.
The chuck must be removed in order to use some
accessories. To remove:
•
Lock the switch trigger by placing the direction of
rotation selector in center position. See Figure 13.
•
Insert a 5/16 inch or larger hex key wrench into the
chuck of yo_Jrdrill and tighten the chuck jaws securely.
•
Tap the wrench sharply with a mallet in a clockwise
direction. See Figure 20. This will loosen the screw in
the chuck for easy removal.
MALLET
CHUCKJAWS
Fig, 22
TO RETIGHTEN
HEX KEY
WRENCH
KEYLESS
CHUCK
Fig. 20
Open chuck jaws and remove wrench. Remove the
chuck screw by turning it in a clockwise direction. See
Figure 21.
A LOOSE
CHUCK
The chuck may become loose on spindle and develop a
wobble. Also, the chuck screw may become loose causing the chuck jaws to bind and prevent them from closing.
To tighten, follow these steps:
Note: The screw has left hand threads:
SCREWDRIVER
Fig. 21
16
•
Lock the switch trigger by placing the direction of
rotation selector in center position. See Figure 13.
•
Insert hex key wrench into chuck and tighten chuck
jaws securely. Tap wrench sharply with a mallet in a
clockwise direction. This will tighten chuck on the
spindle.
•
Open the chuck jaws and remove wrench.
•
Tighten the chuck screw.
Note: The chuck screw has left hand threads.
,_
Do not abuse power tools. Abusive practices can damage
WARNING:
When servicing use only identical
Craftsman replacement parts. Use of any other
parts may create a hazard or cause product damage.
tool as well as workpiece.
Only the parts shown on parts list, page 19, are intended
to be repaired or replaced by the customer. All other parts
should be replaced by a qualified service technician at an
authorized service facility.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, carbon dust, etc.
,_
,_
WARNING:
Do not at any time let brake fluids,
gasoline, petroleum-based products, penetrating oils,
etc. come in contact with plastic parts. They contain
chemicals that can damage, weaken, or destroy
plastic.
WARNING:
Do not attempt to-modify this tool or
create accessories not recommended for use with
this tool. Any such alteration or modification is
misuse and could result in a hazardous condition
leading to possible serious personal injury.
BATTERIES
Store and charge your batteries in a cool area.
Temperatures above normal room temperature will
shorten battery life.
The battery pack for your drill is equipped with nickelcadmium rechargeable batteries. Length of service from
each charging will depend on the type of work you are
doing.
Never store batteries in a discharged condition.
Recharge them immediately after they are
discharged.
The batteries in this tool have been designed to provide
maximum trouble free life. However, like all batteries, they
will eventually wear out. Do not disassemble battery pack
and attempt to replace the batteries. Handling of these
batteries, especially when wearing rings and jewelry,
could result in a serious burn.
All batteries gradually lose their charge. The higher
the temperature the quicker they lose their charge. If
you store your tool for long periods of time without
using it, recharge the batteries every month or two.
This practice will prolong battery life.
To obtain the longest possible battery life, we suggest the
following:
BATTERY
To preserve natural resources, please
recycle or dispose of properly.
PACK REMOVAL
AND PREPARATION
FOR RECYCLING
This product contains nickel-cadmium
batteries. Local, state or federal laws
may prohibit disposal of nickeFcadmium
batteries in ordinary trash.
A
Consult your local waste authority for information
regarding available recycling and/or disposal options.
WARNING:
Upon removal, cover the battery pack's
terminals with heavy duty adhesive tape. Do not
attempt to destroy or disassemble battery pack or
remove any of its components. Nickel-cadmium
batteries must be recycled or disposed of properly.
Also, never touch both terminals with metal objects
and/or body parts as short circuit may result. Keep
away from children. Failure to comply with these
warnings could result in fire and/or serious injury.
OVERLOAD
Your drill has a built-in overload protector to protect the motor during overloading or prolonged use. The overload
protector automatically activates to break the circuit. When this occurs, allow your drill to cool a few seconds before
resuming operation.
17
Thefollowingrecommended
accessories
arecurrentlyavailableatSearsRetailStores.
•
HighSpeedBits......1/2in. Max.
•
6-Pc.ExtraLengthMagnitePowerBitSet
•
WoodBoringBits......1-1/4in. Max.
•
30-Pc.PowerScrewdriver/Nutdriver
SetandCase
•
MasonryBits......1/2in. Max.
•
17-Pc.PowerScrewdriver/Nutdriver
SetandCase
_
_IL
WARNING:
The use of attachments or accessories not listed might be hazardous.
WARNING:
The operation of any power tool can
result in severe eye damage. Before
safety glasses with side shields and
Safety Mask for use over eyeglasses
Retail Stores.
result in foreign objects being thrown into your eyes, which can
beginning power tool operation, always wear safety goggles or
a full face shield when needed. We recommend Wide Vision
or standard safety glasses with side shields, available at Sears
WARRANTY
FULL ONE YEAR WARRANTY
ON I:RRFT$1qRN PROFESSIONAL
CORDLESS HAMMER
DRILL
If this rRRFTSMRN Professional Cordless Hammer Drill fails due to a defect in material or workmanship
from the date of purchase, Sears will repair it, free of charge.
within one year
WARRANTY SERVICE IS AVAILABLE BY SIMPLY RETURNING THE TOOL TO THE NEAREST SEARS STORE IN
THE UNITED STATES.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179
SAVE THESEINSTRUCTIONS
18
CRAFTSMAN
1/2 in. PROFESSIONAL
CORDLESS
MODEL NO, 315.271270
HAMMER
DRILL
t
I
The model number will be found on a plate attached to the motor housing. Always mention the model number
in all correspondence regarding your CRAFTSMAN 1/2 in. PROFESSIONAL
CORDLESS HAMMER
DRILL or when ordering repair parts.
SEE BACK
PAGE FOR PARTS
ORDERING
INSTRUCTIONS
3
2
4
5
6
\
0
PARTS
Key
No.
Pa_
Number
LIST
Description
Quan.
1
975379-000
Screw (Special) .............................................................................................
1
2
979599-000
Auxiliary Handle Assembly ............................................................................
1
3
975111-001
1/2 in. Chuck (Item No. 9_-20956) ..................................................................
1
4
981501-001
Logo Plate .....................................................................................................
1
Battery Pack (Include Part Number 981404-001) .........................................
1
Depth Gage Rod ...........................................................................................
1
5
6
7
8
* 9-11034
980199-000
* 9-11040
Battery Charger (includes Part Number 981399-001) ..................................
1
981500-001
Carrying Case - Not Shown ..........................................................................
1
972000-717
Owner's Manual
* Can Be Purchased At Your Nearest Sears Retail Store
19
In U.S.A. or Canada
for in-home major brand repair service:
Call 24 hours a day, 7 days a week
1-800-4-MY-HOME
Para pedir servicio de reparacibn
s_ (1-800-469-4663)
a domicilio
- 1-800-676-5811
Au Canada pour tout le service ou les pieces - 1-800-469 4663
For the repair or replacement
parts you need:
Call 6 a.m. - 11 p.m. CST, 7 days a week
Parts Direct s.
1-800-366-PART
Para ordenar
piezas con entrega
(1-800-366-7278)
a domicilio - 1-800-659-7084
For the location of a Sears Service Center in your area:
Call 24 hours a day, 7 days a week
1-800-488-1222
To purchase or inquire about a Sears Maintenance Agreement:
Call 7 a.m. - 5 p.m. CST, Monday - Saturday
1-800-827-6655
HomeCentral
s°
Download PDF

advertising