burglar alarm systems 2016 catalogue
BURGLAR ALARM
SYSTEMS
2016 CATALOGUE
CAME GROUP
A SINGLE GLOBAL CONTACT
TRADING
BRANCHES IN ITALY
Came Nord Est Srl
Via Barone, 2/c
33050 Fiumicello (UD)
Tel. +39 0431/970210
Fax +39 0431/970220
E-mail address
for all retail outlets:
Came Centro Srl
Via Caselle, 25
25010 San Zeno Naviglio (BS)
Tel. +39 030/2667564
Fax +39 030/2667380
E-mail address
for all retail outlets:
[email protected]
[email protected]
Came Nord Ovest Srl
Via C. Cavallotto, 10
12060 Roddi (CN)
Tel. +39 0173 620511
Fax +39 0173 620555
[email protected]
Opening soon
Florence branch
Udine branch
Via Tavagnacco, 91/8
33100 Udine (UD)
Tel. +39 0432 484899
Fax +39 0432 484345
Mantua branch
Via Sandro Pertini, 2
46045 Marmirolo (MN)
Tel. +39 0376 299350
Fax +39 0376 294479
Padua branch
Via A. Volta, 21/B
35010 Limena (PD)
Tel. +39 049 8842518
Fax +39 049 8845042
Bologna branch
Via Roma, 120
40012 Calderara di Reno (BO)
Tel. +39 051 728135
Treviso branch
Via della Pace, 30
31030 Dosson di Casier (TV)
Tel. +39 0422 494298
fax +39 0422 494276
Parma branch
Via Giovanni Giolitti, 2A
43126 Parma (PR)
Tel. +39 0521 942551
Fax +39 0521 943721
Came Sud Srl
Via Ferrante Imparato, 198
Lotto A/7
80146 Naples
Tel. +39 081/7524455
Fax +39 081/7529190
[email protected]
Ever since Came Cancelli Automatici was founded in
1972, Came has been leading the way in the design,
development and manufacturing of entry-point operators.
With over forty years' experience, the Came group has
built up a global network of industry-leading partners.
Came S.p.A., a group well-known both in Italy and
worldwide in the Home & Building Automation sector, is
today a global partner in the field of control in the home,
public spaces and in the world of urban planning, for
which it offers integrated solutions for parking facilities,
management of flows
and security.
A large group - represented by the
Came Safety&Comfort trademark - which designs,
makes and markets automation solutions
for entry-points, home automation systems, burglar alarm
and video surveillance systems, video entry systems,
temperature control and LED lighting for residential and
industrial environments.
TECHNICAL
SUPPORT
CENTRES
A widespread network of service centres
able to provide rapid,
competent support for any requirements.
came.com service section
EXPO MILANO 2015
ALL OF CAME'S EXPERTISE
AT THE SERVICE OF THE
DIGITAL SMART CITY
AT EXPO MILANO 2015
The all-round offer, the focus on innovation and the ability
to integrate the most advanced technologies made Came
the technology partner of EXPO Milano 2015, managing
access control for 21 million visitors
to the Universal Exposition.
With the XVia turnstile and the access control system
designed especially for EXPO Milano 2015,
Came, along with the event's main technology partners,
contributed to undertaking the most important Italian
project for a Digital Smart City.
An objective reached in terms of innovation and
modernisation also thanks to the latest-generation
technological solutions, 100% Made in Italy, with the
Came brand.
CAME
OFFICIAL PARTNER
OF EXPO MILANO 2015
CAMECONNECT
A SINGLE SYSTEM TRULY
CONNECTING THINGS AND
PEOPLE
CAME C
USER
TURNSTILES
AUTOMATIC PARKING
FACILITIES
OPERATORS
AUTOMATIC
DOORS
Came offers a Cloud service that
enables users to enjoy all the functionalities of the
devices installed, not only in a room, but also remotely, via
a simple, safe and highly reliable connection.
Innovative Came Connect technology enables
communication
between your Came system and the Cloud, for total
control in real time.
Advantages for installers.
Users can perform a complete system diagnosis and
identify any problems,
intervening quickly and effectively, with just an internet
connection.
A remote assistance service, added value for customers
and your business.
Advantages for users.
Using the special app, just a few clicks connects users in
total safety, so they can check the status of all the areas,
the images from the cameras, activate scenarios,
manage various appliances and interact with their homes
remotely, simply using their smartphone,
tablet or PC.
CLOUD
INSTALLER
HOME AUTOMATION
SECURITY
TEMPERATURE
CONTROL
VIDEO ENTRY
SYSTEMS
CCTV
CAME GROUP
LEADER IN
HOME & BUILDING
AUTOMATION
Entry
automation
Video entry phones
Alarm
CCTV
Since 1972, CAME has been producing the widest range
of operators for residential and industrial entrances,
parking facilities and access control, including the
development
of home automation and burglar alarm systems.
Tubular
Motors
Home Automation
Temperature Control
LED
Lighting
Parking Facilities and
Barriers
Bollards
Access
Control
CONTENTS
12
14 18 KEY TO ICONS
SELECTION GUIDE
20
20 24 28 32 WIRED CONTROL UNITS
PROXINET8
PROXINET36
PROXINET76
PROXINET192
36
36 WIRELESS CONTROL UNITS
PROXINET W2
40 EXPANSION MODULES
40 CONTROL DEVICES
40KEYPADS
41READERS
42 42
42
43
44 48 51 COMMUNICATION MODULES
PSTN MODULES
GSM MODULES
VOICE CARDS
GPRS MODULES
LAN CARDS
KNX CARDS
52 WIRELESS DEVICES
53RECEIVERS
53 VOLUMETRIC DETECTORS FOR INDOOR USE
53 PERIMETER DETECTORS
54 DETECTORS WITH CAMERA
56 CURTAIN-EFFECT DETECTORS
58 DETECTORS FOR OUTDOOR USE
59 CONTROL DEVICES
59SIRENS
62 62 63 65 VOLUMETRIC DETECTORS FOR INDOOR USE
WALL-MOUNTED DETECTORS
RECESSED DETECTORS
CURTAIN-EFFECT DETECTORS
66 66 66
VOLUMETRIC DETECTORS FOR OUTDOOR USE
CURTAIN-EFFECT DETECTORS
WALL-MOUNTED DETECTORS
67 67 67 68 68 68 PERIMETER DETECTORS
MAGNETIC CONTACTS
MAGNETIC CONTACTS FOR DOORS AND FIXTURES IN FERROUS MATERIAL
SPECIAL MAGNETIC CONTACTS
VIBRATION AND MOTION DETECTORS
ACCESSORIES FOR PERIMETER DETECTORS
69BARRIERS
69
INFRARED BARRIERS FOR DOORS AND WINDOWS
70
INFRARED BARRIERS FOR DOORS AND WINDOWS CONFIGURED FOR WIRELESS TRANSMITTERS
71
INFRARED BARRIERS FOR OUTDOOR USE
72
72
72
DETECTORS FOR TECHNICAL ALARMS
LIQUID DETECTORS
MANUAL ALARM ACTIVATORS
73
73 73
73
WIRED SIRENS
SIRENS FOR OUTDOOR USE
SIRENS FOR INDOOR USE
ACCESSORIES FOR SIRENS
74
UNIVERSAL TELEPHONE DIALLERS
75
POWER SUPPLIES AND BATTERIES
75 UNIVERSAL POWER SUPPLIES
75
POWER SUPPLIES SUPERVISED ON BUS
75BATTERIES
76ACCESSORIES
77KITS
78
ANALYTICAL INDICES
13
KEY TO ICONS
Control Unit Identification
PROXINET8
PROXINET8
PROXINET36
Identifies
control unit devices.
This control unit, with 12 inputs, expandable to
20 wired and 16 wireless inputs, is used in
medium systems that require the ability to use
wireless devices.
KEY TO ICONS
Identifies
control unit devices.
This control unit is not expandable and is used
in small systems where high performance is
required at a low cost.
PROXINET36
PROXINET76
Identifies PROXINET76 control unit devices.
This control unit, with 12 inputs, expandable to
36 wired and 40 wireless inputs, is used in
medium to large systems that require the ability
to expand the system in wired or wireless
mode at any time.
Standards and
approvals
PROXINET192
Identifies PROXINET192 control unit devices.
This control unit, with 16 inputs, expandable to
128 wired and 64 wireless inputs, is used in
systems where that require a significant ability
to expand the system and set the access logics
to the various system sectors.
14
PROXINET W2
I
d
e
n
t
i
f
i
e
s
PROXINET W2 control unit devices. This
control unit, with 99 wired and 6 wireless
inputs, is used in systems where a high
standard of protection is required without the
need for building works in order to install the
system.
EN 50131
Product complies with the EN 50131 series
standards where applicable.
Technical features
WIRELESS device
EXP
PXManager
Identifies control units that can be programmed
via a PC equipped with PXManager
programming software.
KEY TO ICONS
Identifies a device that communicates with Identifies control units that feature wired and
other components of the system using radio wireless expansion.
frequency technology.
Compatibility
CAME CLOUD
Video verification
Identifies devices that support the video
verification function, i.e. the ability to record
one or more images, or a video clip, following
an alarm event.
HOME AUTOMATION
Identifies control units that can interact with the
CAME Domotic 3.0 home automation system.
CAME CLOUD
Identifies the control units that be connected to
the CAME CLOUD.
15
5 CONTROL UNITS
For all protection requirements
Thanks to the experience gained over the years, BPT is now presenting the latest generation of the PROXINET line, a range of
products for the burglar alarm industry with innovative features. The range of control units, broad and varied, means that it is
possible to manage from 8 to 192 inputs.
It starts with PROXINET8, the entry level model for small systems where the required performance is still high: it has 8
programmable inputs, keypad and transponder key reader on board. The container can also house PSTN and/or GSM
telephone diallers.
PROXINET36, PROXINET76 and PROXINET192, on the other hand, are models that feature expansion with both specific wireless
devices and expansion modules on bus.
The range is completed with PROXINET W2, a wireless control unit with built-in keypad, display, transponder key reader and
siren that combines the professional characteristics of the full range with the ease of installation of a wireless system.
The control units can be connected via a special interface to a LAN, and thus be accessible by portable devices (PCs,
smartphones, tablets) via a local connection or over the internet by connecting to the Came Cloud.
The system also feature an alarm video verification function. Thanks to special detectors with cameras on board, it is possible
to obtain a sequence of images or a video clip linked to an alarm event, making it possible to discriminate between any false
alarms and the actual presence of intruders in the protected environment.
The latest generation CAME D app, simple and intuitive, gives users complete control over the system.
All the control units provide ample opportunities for connecting to home automation systems. They can in fact be integrated
with the Came Domotic 3.0 system or connected, via a special interface, to systems made with the KNX protocol.
16
They are expandable with specific
wireless devices or expansion
modules on bus.
From 8 to 192 inputs.
They can be integrated into
the Came Domotic 3.0 home
automation system.
CAME CLOUD
They can be connected to the cloud
via CAME Connect technology
for complete remote control from
both users as regards system
management and installers
as regards remote assistance
operations.
They can be managed locally and
remotely via graphical maps with
the CAME Domotic app.
Video verification function. Images
and video clips related to alarm
events
They can be integrated with KNX
systems through a special interface.
17
SELECTION
CONTROL UNITS
GUIDE
PICTURE
*
ITEM /CODE
64300070
64300081
64300091
64300111
64300121
DESCRIPTION
PX8IR
64380040
Expansion
module - 8 inputs
on bus
-
Up to 1
Up to 3
Up to 14
-
PX8OR
64380050
Expansion
module - 8
outputs on bus
-
Up to 2
Up to 4
Up to 15
-
PXKIN
64320040
PXKIB
64320030
LED keypad
Up to 4
wired keypad
Up to 4 keypads Up to 8 keypads Up to 16 keypads
(1 LCD wired (1 LCD wired - (1 LCD wired 3 wireless or
7 wireless or
15 wireless or
wired)
wired)
wired)
Up to 2
wired keypad
PXKD
643200190
LCD keypad
Up to 4
wired keypad
Up to 4 keypads Up to 8 keypads Up to 16 keypads
(1 LCD wired (1 LCD wired - (1 LCD wired 3 wireless or
7 wireless or
15 wireless or
wired)
wired)
wired)
Up to 2
wired keypad
PXKTN
64320060
PXKTB
64320050
Capacitive LCD
keypad
Up to 4
wired keypad
Up to 4 keypads Up to 8 keypads Up to 16 keypads
(1 LCD wired (1 LCD wired - (1 LCD wired 3 wireless or
7 wireless or
15 wireless or
wired)
wired)
wired)
Up to 2
wired keypad
PXITU
64330380
Reader for
transponder key
Up to 4
PXTAG
64330020
Transponder key
Up to 16
PXTEL
64380020
PSTN module
Yes
(optional)
No
(built-in)
No
(built-in)
No
(built-in)
Yes
(optional)
PXGSM
64380060
GSM module
Yes
(optional)
Yes
(optional)
Yes
(optional)
Yes
(optional)
Yes
(optional)
PXGPRS
64380240
GPRS module
Yes
(optional)
Yes
(optional)
Yes
(optional)
Yes
(optional)
Yes
(optional)
PXV64
64380070
Voice card
Yes
(optional)
Yes
(optional)
Yes
(optional)
Yes
(optional)
No
(built-in)
PXV256
64380080
Voice card
Yes
(optional)
Yes
(optional)
Yes
(optional)
Yes
(optional)
-
PXLAN
64380090
PXWEB
64380110
LAN cards
Yes
(optional)
Yes
(optional)
Yes
(optional)
Yes
(optional)
Yes
(optional)
*
SELECTION GUIDE
*
18
Up to 4
Up to 8
Up to 16
Up to 20
Up to 50
Up to 50
(99 with PXV256 (99 with PXV256 (99 with PXV256
card)
card)
card)
Up to 2
Up to 20
CONTROL UNITS
*
ITEM /CODE
64300081
64300091
64300111
64300121
DESCRIPTION
PXWRX
64380160
Wireless receiver
-
Up to 2
Up to 8
Up to 16
Up to 2
PXWIR01
64340191
Wireless
volumetric
detector
-
16 wireless
inputs
40 wireless
inputs
64 wireless
inputs
99 wireless
inputs
PXWCOB01
64340211
PXWCOM01
64340221
Wireless
perimeter
detector
-
16 wireless
inputs
40 wireless
inputs
64 wireless
inputs
99 wireless
inputs
PXWIRCB
64340380
Wireless curtaineffect PIR
detector
-
16 wireless
inputs
40 wireless
inputs
64 wireless
inputs
99 wireless
inputs
PXWDTCB
64340390
PXWDTCM
64340410
Wireless curtaineffect DT detector
-
16 wireless
inputs
40 wireless
inputs
64 wireless
inputs
99 wireless
inputs
PXWDTCL
64340360
Wireless curtaineffect DT detector
-
16 wireless
inputs
40 wireless
inputs
64 wireless
inputs
99 wireless
inputs
PXWIRFC
64340440
PXWIRWFC
64340450
Wireless PIR
detector with
camera
-
Up to 6
Up to 6
Up to 6
Up to 6
PXWDTVE
64340370
Wireless
volumetric DT
detector for
outdoor use
-
16 wireless
inputs
40 wireless
inputs
64 wireless
inputs
99 wireless
inputs
PXWRC
64320021
Remote control
-
Up to 8
Up to 32
Up to 32
Up to 32
PXWKTN
64320080
PXWKTB
64320070
Wireless
capacitive LCD
keypad
-
PXWSE
64420050
Wireless siren for
outdoor use
-
Up to 2
Up to 4
Up to 8
Up to 4
PXManager
Programming
software
YES
YES
YES
YES
YES
Up to 4 keypads Up to 8 keypads Up to 16 keypads
(1 LCD wired (1 LCD wired - (1 LCD wired 3 wireless or
7 wireless or
15 wireless or
wired)
wired)
wired)
Up to 38
* With the exception of systems featuring Proxinet8 and Proxinet W2 control units, at least one PXKD - PXKTN - PXKTB wired
LCD keypad must be included in every system.
19
SELECTION GUIDE
PICTURE
64300070
WIRED CONTROL UNITS
Proxinet 8 is a programmable control unit with 8 inputs. It has a keypad and display which can be used to manage the system
and program the functional parameters. It features a transponder key reader which, thanks to a special electronic key, allows
the systems to be armed, disarmed and partialised.
The inputs can be grouped into 8 individually programmable areas.
There are 4 programmable outputs, which can be paired with control unit events or activated remotely.
An RS485 bus line can connect up to 4 keypads and 4 transponder readers.
The PSTN PXTEL telephone communicator and the PXV64 voice card, which can be installed inside the control unit, allow the
alarms to be transmitted in voice form. The messages can be set using the dedicated TTS (Text To Speech) function, which
turns a written text into a voice message.
The PXV64 card also features voice guidance for remote control which, by calling the control unit, makes it possible to perform
a variety of control operations (activating and deactivating the control unit, querying the power and fuse status, querying the
event log, querying and activating outputs) assisted by voice messages.
Proxinet 8 can be completed with the PXGPRS GPRS module so that alarms can also be transmitted to the GSM network.
This module can be used to transmit alarms in SMS format and perform remote control operations again described by SMS
messages. PXGPRS also allows:
WIRED CONTROL UNITS
• Direct internet connection to the Cloud for remote control
• System management using the Came D app
• Connection to a LAN using the PXDGETH dongle
• Connecting to a WiFi network using the PXDGWF dongle
Via the LAN connection, it is then possible to connect the control unit to the CAME Domotic 3.0 home automation system in
order to achieve centralised control and full integration between the two systems.
The control unit comes with a weekly programmable timer that allows users to manage various control unit functions
automatically at scheduled times.
Programming operations can be carried out using the PX Manager Software by connecting your PC to the RS232 port provided
on board or reaching the control unit via the LAN.
PROXINET8 is an excellent solution for small systems, where high performance is required but cost is also an important aspect
not to be overlooked.
20
Sample installation of PROXINET 8 control unit
sms
Telephone
PXGPRS
SA10L
GPRS module
Siren for
outdoor use
Smartphone
PXV64 /PXV256
Voice card
PXTEL
PSTN dialler
PXKIN
LED keypad
Tablet
WIRED CONTROL UNITS
PXKTN
up to 4
keypads
Wired keypad
PXDGETH
LAN dongle (1)
PXITU
Transponder key
reader - up to 4
PXIPC
CAME CLOUD
Programming
cable
PXTAG
Switch
Transponder key
Modem router
Local PC
Home Automation
system
CAME Domotic 3.0
• LAN
• INTERNET
• RS485 bus
• PSTN line
• Internal connection
• Standard connection
• Wireless connection
(1) PXDGETH dongle to connect to the PXGPRS module.
21
The
PROXINET8 control unit
Burglar alarm system control unit with 8 inputs and built-in
keypad and display. Transponder key reader provided on board.
4 programmable outputs. 4 areas for system management.
RS485 bus line for connection of keypads and remote
transponder key readers. PSTN and GSM telephone diallers can
be installed internally. Can be connected to the LAN through a
special interface. Programmable from keypad or PC. Supplied
with 1 x transponder key.
Item PROXINET8
Code 64300070
WIRED CONTROL UNITS
CAME CLOUD
TECHNICAL FEATURES
DESCRIPTION
22
Power supply
230 V AC –15% + 10% 50/60 Hz
Card current draw
(excluding battery charging and accessory cards)
70 mA
Power supply
1A
Transformer
25 VA
Battery
7.2 Ah
Protection rating
IP30
Dimensions
350 x 230 x 85 mm
Weight (without battery)
1.7 kg
Container material
ABS
Operating temperature
From -10 ° to +40 °C
Storage temperature
From -10 ° to +50 °C
Relative humidity during operation
75% RH non-condensing
Relative humidity during storage
75% RH non-condensing
Regulatory compliance
EN 50131-6; EN 50131-3 Grade 2 Environmental Class II
WIRED CONTROL UNITS
FUNCTIONAL FEATURES
DESCRIPTION
Basic control unit inputs
8
Alarm outputs
1
Programmable outputs (OC) on the control unit
4
Built-in keypad
Yes
Built-in transponder reader
Yes
Bus
1 x RS485 line
Areas
4
Scenarios
6
Readers
4
Wired keypads
4
Keys
16
User codes
16
Programmable timer
Daily On/Off control unit and outputs
Events
250
PSTN communicator
PXTEL module
GSM or GPRS module
PXGSM or PXGPRS module
Control via SMS
With PXGSM or PXGPRS module
Remote control with voice guidance
With PXV64 voice card and PXTEL, PXGSM or PXGPRS modules
Communication port
RS232
LAN connection
With PXLAN or PXWEB card or with PXGPRS module and PXDGETH LAN
dongle
Remote programming via internet
Yes
Connection to home automation system
Via LAN
23
Proxinet 36 is a programmable control unit with 12 inputs that can be expanded to 20 wired and 16 wireless inputs. It has an
RS485 BUS line to which external devices can be connected. To expand the 12 basic inputs, users can use a PX8IR remote
module with 8 inputs to be connected on the bus, while by using the PXWRX wireless receiver, again connected to the bus
line, users can access a further 16 wireless inputs available on the control unit. The inputs can be grouped into 4 individually
programmable areas.
There are 4 programmable outputs on board which can be expanded to 20, using 2 PX8OR remote expansion modules with 8
outputs to be connected on the bus. All the outputs are programmable, and can therefore be paired with control unit events or
activated remotely.
It is also possible to connect up to 4 keypads and 4 PXIT transponder readers on the bus line.
The PSTN telephone communicator is integrated on board and enables the transmission of alarms in digital format towards
security companies and can be coupled to the PXV64 or PXV256 voice card for the transmission of alarms in voice format. The
messages can be set using the dedicated TTS (Text To Speech) function, which turns a written text into a voice message.
The PXV64 (or PXV256) card also features voice guidance for remote control which, by calling the control unit, makes it
possible to perform a variety of control operations (activating and deactivating the control unit, querying the power and fuse
status, querying the event log, querying and activating outputs) assisted by voice messages.
WIRED CONTROL UNITS
Proxinet 36 can be completed with the PXGPRS GPRS module so that alarms can also be transmitted to the GSM network.
This module can be used to transmit alarms in SMS format and perform remote control operations again described by SMS
messages. PXGPRS also allows:
• Direct internet connection to the Cloud for remote control
• System management using the Came D app
• Support for video verification function
• Connection to a LAN using the PXDGETH dongle
• Connecting to a WiFi network using the PXDGWF dongle
Via the LAN connection, it is then possible to connect the control unit to the CAME Domotic 3.0 home automation system in
order to achieve centralised control and full integration between the two systems.
The control unit comes with a weekly programmable timer that allows users to manage various control unit functions
automatically at scheduled times.
Programming operations can be carried out using the PX Manager Software by connecting your PC to the RS232 port provided
on board or reaching the control unit via the LAN.
PROXINET36 is an excellent solution for small to medium systems, where it is necessary to have wireless devices.
24
Sample installation of PROXINET 36 control unit
PXGPRS
sms
Telephone
PXV64
PXV256
GPRS module (1)
SA10L
Siren for
outdoor use
Voice
card
Smartphone
PXKIN
LED keypad
PXKTN
Tablet
Wired keypad
PXITU
Transponder key
reader - up to 4
WIRED CONTROL UNITS
up to 4
keypads
PXDGETH
LAN dongle (1)
PXIPC
Programming
cable
CAME CLOUD
Switch
Modem router
PX8IR
Local PC
Expansion module with
8 inputs
Home Automation
system
CAME Domotic 3.0
PX8OR
Expansion module with
8 outputs - up to 2
PXWRC
Remote control
PXWRX
Wireless
receiver - up to 2
• LAN
• INTERNET
• RS485 bus
• PSTN line
• Internal connection
• Standard connection
• Wireless connection
PXWCOB01
16 wireless
inputs
Wireless perimeter
detector
PXWIR01
Wireless volumetric detector
(1) PXDGETH dongle to connect to the PXGPRS module.
25
The
PROXINET36 control unit
Burglar alarm system control unit with 12 inputs that
can be expanded to 20 wired and 16 wireless inputs. 4
outputs that can be expanded to 20; 4 areas for system
management. RS485 bus line for connection of keypads and
remote transponder key readers. Built-in PSTN telephone
communicator. Can be connected to the LAN through a special
interface. Programmable from keypad or PC.
Item PROXINET36
Code 64300081
WIRED CONTROL UNITS
CAME CLOUD
TECHNICAL FEATURES
DESCRIPTION
26
Power supply
230 V AC –15% + 10% 50/60 Hz
Card current draw
(excluding battery charging and accessory cards)
70 mA
Power supply
1A
Transformer
20 VA
Battery
7.2 Ah
Protection rating
IP30
Dimensions
305 x 215 x 70 mm
Weight (without battery)
1.9 kg
Container material
Metal
Operating temperature
From -10 ° to +40 °C
Storage temperature
From -10 ° to +50 °C
Relative humidity during operation
75% RH non-condensing
Relative humidity during storage
75% RH non-condensing
Regulatory compliance
EN 50131-6; EN 50131-3 Grade 2 Environmental Class II
FUNCTIONAL FEATURES
Basic control unit inputs
12
Remote inputs on bus
8
Wireless inputs
16 (with PXWRX module)
Total inputs
20 wired + 16 wireless
Alarm outputs
1
Programmable outputs (OC) on the control unit
4
Programmable remote outputs on bus
16
Total programmable outputs.
20
Built-in keypad
No
Bus
1 x RS485 line
Areas
4
Scenarios
32
Readers
4
*Keypads (wireless or wired)
4 (1 LCD wired -3 wireless or wired)
Keys
20 (99 with PXV256 card)
Remote controls
8
Wireless sirens
2
User codes
20 (99 with PXV256 card)
Programmable timer
Weekly for complete system management
Events
250 (999 with PXV256 card)
PSTN communicator
Built-in
GSM or GPRS module
PXGSM or PXGPRS module
Control via SMS
With PXGSM or PXGPRS module
Remote control with voice guidance
With PXV64 or PXV256 voice card
Communication port
RS232
LAN connection
With PXLAN or PXWEB card or with PXGPRS module and PXDGETH LAN
dongle
Remote programming via internet
Yes
Connection to home automation system
Via LAN
WIRED CONTROL UNITS
DESCRIPTION
*At least one wired PXKD - PXKTN - PXKTB LCD keypad must be included.
27
Proxinet 76 is a programmable control unit with 12 inputs that can be expanded to 36 wired and 40 wireless inputs. It has an
RS485 BUS line to which external devices can be connected. To expand the 12 basic inputs, users can use 3 PX8IR remote
modules with 8 inputs to be connected on the bus, while by using the PXWRX radio receiver, again connected to the bus line,
users can access a further 40 wireless inputs available on the control unit. The inputs can be grouped into 8 individually
programmable areas.
There are 4 programmable outputs on board which can be expanded to 36, using 4 PX8OR remote expansion modules with 8
outputs to be connected on the bus. All the outputs are programmable, and can therefore be paired with control unit events or
activated remotely.
It is also possible to connect up to 8 keypads and 8 PXIT transponder readers on the bus line.
The PSTN telephone communicator is integrated on board and enables the transmission of alarms in digital format towards
security companies and can be coupled to the PXV64 or PXV256 voice card for the transmission of alarms in voice format. The
messages can be set using the dedicated TTS (Text To Speech) function, which turns a written text into a voice message.
The PXV64 (or PXV256) card also features voice guidance for remote control which, by calling the control unit, makes it
possible to perform a variety of control operations (activating and deactivating the control unit, querying the power and fuse
status, querying the event log, querying and activating outputs) assisted by voice messages.
WIRED CONTROL UNITS
Proxinet 76 can be completed with the PXGPRS GPRS module so that alarms can also be transmitted to the GSM network.
This module can be used to transmit alarms in SMS format and perform remote control operations again described by SMS
messages. PXGPRS also allows:
• Direct internet connection to the Cloud for remote control
• System management using the Came D app
• Support for video verification function
• Connection to a LAN using the PXDGETH dongle
• Connecting to a WiFi network using the PXDGWF dongle
Via the LAN connection, it is then possible to connect the control unit to the CAME Domotic 3.0 home automation system in
order to achieve centralised control and full integration between the two systems.
The control unit comes with a weekly programmable timer that allows users to manage various control unit functions
automatically at scheduled times.
Programming operations can be carried out using the PX Manager Software by connecting your PC to the RS232 port provided
on board or reaching the control unit via the LAN.
PROXINET76 is an excellent solution for medium to large systems, where it is necessary to be able to expand the system using
wired or wireless devices at any time.
28
Sample installation of PROXINET 76 control unit
sms
PXGPRS
GPRS module (1)
PXV64
PXV256
Telephone
SA10L
Siren for
outdoor use
Voice
card
Smartphone
PXKIN
LED keypad
PXKTN
Tablet
Wired keypad
PXITU
Transponder key
reader - up to 8
WIRED CONTROL UNITS
up to 8
keypads
PXDGETH
LAN dongle (1)
PXIPC
Programming
cable
CAME CLOUD
PXTAG
Transponder key
Switch
PX8IR
Expansion module with
8 inputs - up to 3
Modem router
Local PC
Home Automation
system
CAME Domotic 3.0
PX8OR
Expansion module with
8 outputs - up to 4
PXWRC
Remote control
PXWRX
Wireless
receiver - up to 8
• LAN
• INTERNET
• RS485 bus
• PSTN line
• Internal connection
• Standard connection
• Wireless connection
PXWCOB01
Wireless perimeter
detector
40 wireless
inputs
PXWIR01
Wireless volumetric detector
(1) PXDGETH dongle to connect to the PXGPRS module.
29
The
PROXINET76 control unit
Burglar alarm system control unit with 12 inputs that can be
expanded to 36 wired and 40 wireless inputs. 4 outputs that
can be expanded to 36; 8 areas for system management.
RS485 bus line for connection of keypads and transponder
key readers. Built-in PSTN telephone communicator. Can
be connected to the LAN through a special interface.
Programmable from keypad or PC.
Item PROXINET76
Code 64300091
WIRED CONTROL UNITS
CAME CLOUD
TECHNICAL FEATURES
DESCRIPTION
30
Power supply
230 V AC –15% + 10% 50/60 Hz
Card current draw
(excluding battery charging and accessory cards)
70 mA
Power supply
1.5 A
Transformer
38 VA
Battery
7.2/17 Ah
Protection rating
IP30
Dimensions
405 x 295 x 90 mm
Weight (without battery)
1.9 kg
Container material
Metal
Operating temperature
From -10 ° to +40 °C
Storage temperature
From -10 ° to +50 °C
Relative humidity during operation
75% RH non-condensing
Relative humidity during storage
75% RH non-condensing
Regulatory compliance
EN 50131-6; EN 50131-3 Grade 2 Environmental Class II
FUNCTIONAL FEATURES
Basic control unit inputs
12
Remote inputs on bus
24
Wireless inputs
40 (with PXWRX module)
Total inputs
36 wired + 40 wireless
Alarm outputs
2
Programmable outputs (OC) on the control unit
4
Programmable remote outputs on bus
32
Total programmable outputs.
36
Built-in keypad
No
Bus
1 x RS485 line
Areas
8
Scenarios
32
Readers
8
*Keypads (wireless or wired)
8 (1 LCD wired -7 wireless or wired)
Keys
50 (999 with PXV256 card)
Remote controls
32
Wireless sirens
4
User codes
50 (999 with PXV256 card)
Programmable timer
Weekly for complete system management
Events
999 (9999 with PXV256 card)
PSTN communicator
Built-in
GSM or GPRS module
PXGSM or PXGPRS module
Control via SMS
With PXGSM or PXGPRS module
Remote control with voice guidance
With PXV64 or PXV256 voice card
Communication port
RS232
LAN connection
With PXLAN or PXWEB card or with PXGPRS module and PXDGETH LAN
dongle
Remote programming via internet
Yes
Connection to home automation system
Via LAN
WIRED CONTROL UNITS
DESCRIPTION
*At least one wired PXKD - PXKTN - PXKTB LCD keypad must be included.
31
Proxinet192 is a programmable control unit with 16 inputs that can be expanded to 128 wired and 64 wireless inputs. It has an
RS485 BUS line to which external devices can be connected. To expand the 16 basic inputs, users can use 14 PX8IR remote
module with 8 inputs to be connected on the bus, while by using the PXWRX radio receiver, again connected to the bus line,
users can access a further 64 wireless inputs available on the control unit. The inputs can be grouped into 16 individually
programmable areas.
There are 8 programmable outputs on board which can be expanded to 128, using 15 PX8OR remote expansion modules with
8 outputs to be connected on the bus. All the outputs are programmable, and can therefore be paired with control unit events
or activated remotely.
It is also possible to connect up to 16 keypads and 16 PXIT transponder readers on the bus line.
The PSTN telephone communicator is integrated on board and enables the transmission of alarms in digital format towards
security companies and can be coupled to the PXV64 or PXV256 voice card for the transmission of alarms in voice format. The
messages can be set using the dedicated TTS (Text To Speech) function, which turns a written text into a voice message.
The PXV64 (or PXV256) card also features voice guidance for remote control which, by calling the control unit, makes it
possible to perform a variety of control operations (activating and deactivating the control unit, querying the power and fuse
status, querying the event log, querying and activating outputs) assisted by voice messages.
WIRED CONTROL UNITS
Proxinet192 can be completed with the PXGPRS GPRS module so that alarms can also be transmitted to the GSM network.
This module can be used to transmit alarms in SMS format and perform remote control operations again described by SMS
messages. PXGPRS also allows:
• Direct internet connection to the Cloud for remote control
• System management using the Came D app
• Support for video verification function
• Connection to a LAN using the PXDGETH dongle
• Connecting to a WiFi network using the PXDGWF dongle
Via the LAN connection, it is then possible to connect the control unit to the CAME Domotic 3.0 home automation system in
order to achieve centralised control and full integration between the two systems.
The control unit comes with a weekly programmable timer that allows users to manage various control unit functions
automatically at scheduled times.
Programming operations can be carried out using the PX Manager Software by connecting your PC to the RS232 port provided
on board or reaching the control unit via the LAN.
PROXINET192 is an excellent solution for systems that require a significant ability to expand the system and set the access
logics to the various system sectors.
32
Sample installation of PROXINET 192 control unit
sms
PXGPRS
GPRS module (1)
PXV64
PXV256
Telephone
SA10L
Siren for
outdoor use
Voice
card
Smartphone
PXKIN
LED keypad
PXKTN
Tablet
Wired keypad
PXITU
Transponder key
reader - up to 16
WIRED CONTROL UNITS
up to 16
keypads
PXDGETH
LAN dongle (1)
PXIPC
Programming
cable
CAME CLOUD
PXTAG
Transponder key
Switch
PX8IR
Expansion module with
8 inputs - up to 14
Modem router
Local PC
Home Automation
system
CAME Domotic 3.0
PX8OR
Expansion module with
8 outputs - up to 15
PXWRC
Remote control
PXWRX
Wireless
receiver - up to 16
• LAN
• INTERNET
• RS485 bus
• PSTN line
• Internal connection
• Standard connection
• Wireless connection
PXWCOB01
Wireless perimeter
detector
64 wireless
inputs
PXWIR01
Wireless volumetric detector
(1) PXDGETH dongle to connect to the PXGPRS module.
33
The
PROXINET192 control unit
Burglar alarm system control unit with 16 inputs that can be
expanded to 128 wired and 64 wireless inputs. 8 outputs that
can be expanded to 128; 16 areas for system management.
RS485 bus line for connection of keypads and transponder
key readers. Built-in PSTN telephone communicator. Can
be connected to the LAN through a special interface.
Programmable from keypad or PC.
Item PROXINET192
Code 64300111
WIRED CONTROL UNITS
CAME CLOUD
TECHNICAL FEATURES
DESCRIPTION
34
Power supply
230 V AC –15% + 10% 50/60 Hz
Card current draw
(excluding battery charging and accessory cards)
71 mA
Power supply
2.5 A
Transformer
52 VA
Battery
17 Ah
Protection rating
IP30
Dimensions
490 x 360 x 90 mm
Weight (without battery)
1.9 kg
Container material
Metal
Operating temperature
From -10 ° to +40 °C
Storage temperature
From -10 ° to +50 °C
Relative humidity during operation
75% RH non-condensing
Relative humidity during storage
75% RH non-condensing
Regulatory compliance
EN 50131-6; EN 50131-3 Grade 2 Environmental Class II
Basic control unit inputs
16
Remote inputs on bus
112
Wireless inputs
64 (with PXWRX module)
Total inputs
128 wired + 64 wireless
Alarm outputs
2
Programmable relay outputs on the control unit
1
Programmable outputs (OC) on the control unit
7
Programmable remote outputs on bus
120
Total programmable outputs.
128
Built-in keypad
No
Bus
2 x RS485 lines
Areas
16
Scenarios
32
Readers
16
*Keypads (wireless or wired)
16 (1 LCD wired -15 wireless or wired)
Keys
50 (999 with PXV256 card)
Remote controls
32
Wireless sirens
8
User codes
50 (999 with PXV256 card)
Programmable timer
Weekly for complete system management
Events
999 (9999 with PXV256 card)
PSTN communicator
Built-in
GSM or GPRS module
PXGSM or PXGPRS module
Control via SMS
With PXGSM or PXGPRS module
Remote control with voice guidance
With PXV64 or PXV256 voice card
Communication port
RS232
LAN connection
With PXLAN or PXWEB card or with PXGPRS module and PXDGETH LAN
dongle
Remote programming via internet
Yes
Connection to home automation system
Via LAN
WIRED CONTROL UNITS
DESCRIPTION
*At least one wired PXKD - PXKTN - PXKTB LCD keypad must be included.
35
WIRELESS CONTROL UNITS
PROXINET W2 is a programmable control unit with 99 wireless and 6 wired inputs. It has a keypad and display which can be
used to manage the system and program the functional parameters. It features a siren for indoor use and a transponder key
reader which, thanks to a special electronic key, allows the systems to be armed, disarmed and partialised. It converses in
Dual Band two-way mode with all of the wireless range devices (described in the relevant section of the catalogue). The inputs
can be grouped into 8 individually programmable areas.
There are 4 programmable outputs, which can be paired with control unit events or activated remotely.
An RS485 BUS line can connect up to 2 wired keypads (PXKTN - PXKTB - PXKD - PXKIN - PXKIB), two transponder key
readers (PXITU) and two additional PXWRX wireless receivers (used to improve the system range).
The PSTN telephone communicator is integrated on board and enables the transmission of alarms in voice format and digital
format towards security companies. The messages can be set using the dedicated TTS (Text To Speech) function, which turns
a written text into a voice message, or they can be recorded using the special built-in microphone.
WIRELESS CONTROL UNITS
It comes with voice guidance, which, thanks to a series of voice messages related to various system statuses and events,
guides the user in using the system. The voice guidance also enables remote control which, by calling the control unit, makes
it possible to perform a variety of control operations (activating and deactivating the control unit, querying the power and fuse
status, querying the event log, querying and activating outputs) assisted by voice messages.
The control unit can be completed with the PXGPRS GPRS module so that alarms can also be transmitted to the GSM network.
This module can be used to transmit alarms in SMS format and perform remote control operations again described by SMS
messages. PXGPRS also allows:
• Direct internet connection to the Cloud for remote control
• System management using the Came D app
• Support for video verification function
• Connection to a LAN using the PXDGETH dongle
• Connecting to a WiFi network using the PXDGWF dongle
Via the LAN connection, it is also possible to connect the control unit to the CAME Domotic 3.0 home automation system in
order to achieve centralised control and full integration between the two systems.
The control unit comes with a daily programmable timer that allows users to manage various control unit functions
automatically at scheduled times.
For simple installations, users can use the self-learning device function that allows users to program the control unit without a
PC, in an easy, immediate way, with dedicated voice guidance.
For complete programming, it is possible to use the PX Manager Software by connecting your PC to the RS232 port provided
on board or reaching the control unit via the LAN.
Together with the high performance of the PROXINET range, PROXINET W2 offers the ease of installation typical of wireless
systems. For this reason, it is an excellent solution to adequately protect your home without resorting to building work.
36
Sample installation of PROXINET W2 control unit
PXWCOB01
Telephone
PXGPRS
Wireless perimeter
detector
PXWSE
GPRS module (1)
Wireless siren
for outdoor use
SA10L
Siren for
outdoor use
sms
PXWIR01
Wireless volumetric detector
Smartphone
PXWKTN
Wireless keypad
PXKIN
LED keypad
PXKTN
Wired keypad
Tablet
PXITU
Transponder key
reader - up to 2
WIRELESS CONTROL UNITS
up to 2
keypads
PXDGETH
LAN dongle (1)
CAME CLOUD
PXTAG
Transponder key
Switch
Modem router
Local PC
Home Automation
system
CAME Domotic 3.0
PXWRC
Remote control
PXWRX
Wireless
receiver - up to 2
• LAN
• INTERNET
• RS485 bus
• PSTN line
• Internal connection
• Standard connection
• Wireless connection
PXWCOB01
Wireless perimeter
detector
99 wireless
inputs
PXWIR01
Wireless volumetric detector
(1) PXDGETH dongle to connect to the PXGPRS module.
37
The
PROXINET W2 control unit
Burglar alarm system control unit with 99 wireless inputs and
6 wired inputs with built-in keypad, display, transponder key
reader and siren for indoor use. 4 programmable outputs;
8 areas for system management. Built-in PSTN telephone
communicator. Built-in speech synthesis for local and remote
system management. Can be connected to the LAN through a
special interface. Programmable from keypad or PC.
Item PROXINET W2
Code 64300121
WIRELESS CONTROL UNITS
CAME CLOUD
TECHNICAL FEATURES
DESCRIPTION
38
Power supply
230 V AC –15% + 10% 50/60 Hz
Card current draw
(excluding battery charging and accessory cards)
70 mA
Power supply
0.8 A
Transformer
25 VA
Battery
2.2 Ah
Protection rating
IP30
Dimensions
300 x 250 x 65 mm
Weight (without battery)
1.5 kg
Container material
ABS
Operating temperature
From -10 ° to +40 °C
Storage temperature
From -10 ° to +50 °C
Relative humidity during operation
75% RH non-condensing
Relative humidity during storage
75% RH non-condensing
Regulatory compliance
EN 50131-6; EN 50131-3 Grade 2 Environmental Class II
FUNCTIONAL FEATURES
Wireless inputs
99
Wired inputs
6
Alarm outputs
1
Programmable outputs (OC) on the control unit
4
Built-in keypad
Yes
Built-in transponder reader
Yes
Siren for indoor use
Built-in (100 dB at 1 m)
Transmission
Dual Band 868.65 MHz and 433.92 MHz Two-Way
Modulation type
GFSK
Bus
1 x RS485 line
Areas
8
Scenarios
16
Readers
2
Wired keypads
2
Additional wireless receivers can be connected on the
bus
2
Keys
20
User codes
20
Remote controls
32
Wireless keypads
8
Wireless sirens
4
Programmable timer
Daily ON/OFF control unit and outputs
Events
999
PSTN communicator
Built-in
GSM or GPRS module
PXGSM or PXGPRS module
Control via SMS
With PXGSM or PXGPRS module
Remote control with voice guidance
Yes
Communication port
USB
LAN connection
With PXLAN or PXWEB card or with PXGPRS module and PXDGETH LAN
dongle
Remote programming via internet
Yes
Connection to home automation system
Via LAN
WIRELESS CONTROL UNITS
DESCRIPTION
39
EXPANSION MODULES
EXPANSION MODULES - CONTROL DEVICES
EXPANSION MODULES
ITEM
CODE
DESCRIPTION
PX8IR
64380040
PX8OR
64380050
EBTAM
64380050
Expansion module - 8 inputs on bus It allows users to expand the number of wired inputs on
Proxinet36, Proxinet76 and Proxinet192 control units. It can be connected to the control unit
via the RS485 bus line. Current draw 40 mA. Dimensions 85.5 x 60 x 21 mm. Regulatory
compliance: EN 50131-3 Grade 2 Environmental Class II. Supplied complete with plastic
container.
Expansion module - 8 outputs on bus It allows users to expand the number of outputs on
Proxinet36, Proxinet76 and Proxinet192 control units. It can be connected to the control unit
via the RS485 bus line. Current draw 40 mA. Dimensions 85.5 x 60 x 21 mm. Compliance
with EN 50131-3 Grade 2 Environmental Class II. Supplied complete with plastic container.
Opening- and teat-resistant cover for PX8IR and PX8OR.
CONTROL DEVICES
KEYPADS
40
ITEM
CODE
DESCRIPTION
PXKD
64320090
Keypad with rubber keys. It allows the programming of all the parameters of the control unit
and total system control through the launch of 16 scenarios (programmed partitions e.g.
“NIGHT” scenario, arming of perimeter area, outdoor area, day area) set on the control unit.
Can be installed directly on the wall. Current draw 60 mA. Dimensions 105 x 140 x 28 mm
Regulatory compliance: EN 50131-3 Grade 2 Environmental Class II.
PXKIN
64320040
PXKIB
64320030
LED keypad. It allows the launch of 3 scenarios (programmed partitions e.g. “NIGHT”
scenario, arming of perimeter area, outdoor area, day area) set on the control unit. Equipped
with reinforcements suitable for installation with plates used in the main wiring systems on a
type 503 box. Current draw 50 mA. Dimensions 66 x 45 x 50 mm Regulatory compliance:
EN 50131-3 Grade 2 Environmental Class II. Black.
LED keypad. White.
(Features as PXKIN).
PXKTN
64320060
PXKTB
64320050
Capacitive keypad with touch keys. It allows the programming of all the parameters of the
control unit and total system control through the launch of 16 scenarios (programmed
partitions e.g. “NIGHT” scenario, arming of perimeter area, outdoor area, day area) set
on the control unit. It features a transponder key reader to use with PXTAG key. It can be
installed directly on the wall or recessed in an OPALESI box (see example of installation).
Current draw 140 mA. Dimensions 158 x 138 x 31 mm Regulatory compliance: EN 50131-3
Grade 2 Environmental Class II. Black.
Capacitive keypad with touch keys. White.
(Features as PXKTN).
READERS
ITEM
CODE
DESCRIPTION
PXITU
64330380
Reader for transponder key. In combination with the PXTAG transponder key, it allows the
launch of 3 scenarios (programmed partitions e.g. “NIGHT” scenario, arming of perimeter
area, outdoor area, day area) set on the control unit. It shows the system status signals. It
can be installed on a hole cover in a recessed wiring system (see example of installation).
Current draw 100 mA. Regulatory compliance: EN 50131-3 Grade 2 Environmental Class II.
PXTAG
64330020
Transponder key. To be paired with a transponder reader. Programmed with factory code to
be transferred in the control unit programming stage. Dimensions 50 x 33 mm. Blue.
Example of installation
RECESSED INSTALLATION
CONTROL DEVICES
WALL MOUNTING
Max overall size
9 mm
INSTALLING A READER ON A HOLE COVER
IN A RECESSED WIRING SYSTEM
HOLE
COVER
BASE MODULE
BOX
41
COMMUNICATION MODULES
PSTN - GSM - VOICE CARDS
The built-in PSTN communicator on Proxinet36, Proxinet76, Proxinet192 and Proxinet W2 control units enables the
transmission of alarms in digital format to security companies with the Contact ID protocol. Using the PXV64 voice card, users
can pair a voice message to be transmitted to a series of telephone numbers to every control unit event. The messages can be
set using the dedicated TTS (Text To Speech) function, which turns a written text into a voice message.
The PXV64 voice card also incorporates voice guidance for remote control. This feature allows users to call the control unit
and perform a series of remote control operations assisted by specific voice messages.
By pairing the control units with the PXGSM GSM telephone module, in addition to transmitting the alarms and performing
remote control operations with voice guidance via the GSM network, it is possible to control the unit remotely using
text messages. Using the PXGSM module, it is also possible to determine which line, PSTN or GSM, will have priority for
transmission and which will act as the auxiliary line if the default line proves unusable.
The main operations that can be carried out remotely via PSTN and GSM line with voice guidance, or via text message, are as
follows:
COMMUNICATION MODULES
• Querying control unit status, arming and disarming the control unit
• Checking for faults and anomalies
• Arming and disarming areas
• Querying, activating and deactivating outputs for remote load control
• Querying inputs
• Querying event log
A second PXV256 voice card is included. This, in addition to the features of the PXV64 model, makes it possible to expand the
number of user codes, transponder key codes and events that can be memorised as set out in the tables that summarise the
functional characteristics of each control unit.
The same considerations apply as regards the Proxinet8 control, with the difference that the PSTN communicator is additional
(PXTEL) and the voice card is the PXV64.
PSTN MODULES
ITEM
CODE
DESCRIPTION
PXTEL
64380020
PSTN telephone dialler. This can send control unit events to 8 telephone numbers. Digital
transmission with contact ID protocol. Used with a voice card, it enables users to send voice
messages and use remote control with voice guidance. Current draw 20 mA. Dimensions 74
x 74 x 32 mm Regulatory compliance: EN 50131-3 Grade 2 Environmental Class II.
ITEM
CODE
DESCRIPTION
PXGSM
64380060
GSM telephone dialler. This can send control unit events to 16 telephone numbers.
Transmission via text message. Used with a voice card, it enables users to send voice
messages and use remote control with voice guidance. Current draw 100 mA. Dimensions
34 x 81 x 30 mm Regulatory compliance: EN 50131-3 Grade 2 Environmental Class II,
R&TTE Directive 99/05 EC.
GSM MODULES
42
COMMUNICATION MODULES
VOICE CARDS
CODE
DESCRIPTION
PXV64
64380070
Voice card. This enables the transmission of alarm messages in voice form and remote
control with voice guidance. It can be programmed with the TTS (Text To Speech) function
that transforms voice messages into written text. Current draw 10 mA. Dimensions 22 x
22 x 12 mm Regulatory compliance: EN 50131-3 Grade 2 Environmental Class II, R&TTE
Directive 99/05 EC.
PXV256
64380080
Voice card. This enables the transmission of alarm messages in voice form and remote
control with voice guidance. It can be programmed with the TTS (Text To Speech) function
that transforms voice messages into written text. It also allows users to extend user codes,
key codes, and the number of events at the highest values envisaged ​​for the Proxinet36,
Proxinet76 and Proxinet192 control units (see control unit functional characteristic tables).
Current draw 10 mA. Dimensions 22 x 22 x 12 mm Regulatory compliance: EN 50131-3
Grade 2 Environmental Class II, R&TTE Directive 99/05 EC.
COMMUNICATION MODULES
ITEM
Example of installation
PXGSM
GSM module
PXV64
PXV256
Voice
card
sms
TRANSMISSION WITH DIGITAL PROTOCOL
TO SECURITY COMPANIES
Smartphone
Telephone
• PSTN line
• Internal connection
43
GPRS
The Came Group offers a Cloud service that guarantees users a simple, secure and highly reliable connection to their system
remotely via the internet. The Cloud is configured to allow users to connect to the system on one hand, in order to enable
remote system management operations using a portable device featuring the Came Domotic APP, and to allow installers to
connect and perform remote assistance operations (diagnosis and programming) with customer authorisation, on the other.
The PXGPRS module, in addition to the typical characteristics of PXGSM module, also makes use of Came Connect technology
for this purposes, allowing the burglar alarm system to be connected to the Cloud via a VPN (Virtual Private Network), as
follows:
• GPRS data connection. This ensures a direct, simple and reliable connection to the Cloud, very useful when no other types
of connection (WiFi or LAN) are available.
• WIFI connection via PXDGWF dongle. This guarantees control unit connection to a LAN and direct connection to a PC to
perform programming operations, via WIFI. In this configuration, it also allows images to be received from the PXWIRWFC
detector.
• LAN connection via PXDGETH dongle. This allows direct wired connection to a LAN and connection to a PC to perform
programming operations.
With the central networked, via WIFI or LAN, you can:
COMMUNICATION MODULES
• Connect the TS7 and TS10 touchscreen terminals from the CAME Domotic 3.0 system and use these to manage the burglar
alarm system using the graphical maps available on the terminals themselves.
• Connect the control unit to the Cloud avoiding the GPRS connection, and manage the system remotely.
• In the case of security systems connected to the CAME Domotic 3.0 system, connect the control unit to the ETI/DOMO home
automation system and ensure seamless integration between the two systems.
GPRS MODULES
44
ITEM
CODE
DESCRIPTION
PXGPRS
64380240
PXDGWF
64440230
GPRS module. It allows you to send control unit events to up to 16 phone numbers via
voice messages (if the PXV64 or PXV256 card is present), sending alarm text messages
and receive text messages and DTMF tones for remote control. It ensures the control unit
connection to the Cloud. It has a connector for connecting the WIFI and LAN dongle.
Current draw 100 mA. Dimensions 34 x 81 x 30 mm Regulatory compliance: EN 50131-3
Grade 2 Environmental Class II, R&TTE Directive 99/05 EC.
WIFI dongle. When used with the PXGPRS module, it enables the control unit to be
connected to a WIFI network.
PXDGETH
64440220
LAN dongle. When used with the PXGPRS module, it enables the control unit to be
connected to a LAN network.
Example of installation
Tablet
PXGPRS
GPRS module
COMMUNICATION MODULES
CAME CLOUD
Example of installation
PXDGWF
Tablet
WIFI dongle
PXGPRS
GPRS module
CAME CLOUD
Switch
Modem router
Touchscreen
• LAN
• INTERNET
• Internal connection
• WIFI connection
Home Automation
system
CAME Domotic 3.0
45
Example of installation
PXDGWF
Tablet
WIFI dongle
PXGPRS
COMMUNICATION MODULES
GPRS module
PXWRX
Wireless receiver
PXWIRWFC
Wireless PIR detector with
camera
INSTALLER
CAME CLOUD
Switch
Modem router
Touchscreen
Home Automation
system
CAME Domotic 3.0
• LAN
• INTERNET
• RS485 bus
• PSTN line
• Internal connection
• Wireless connection
• WIFI connection
46
Example of installation
PXGPRS
GPRS module
PXDGETH
LAN dongle
Tablet
PXDGETH
PXWRX
Wireless receiver
COMMUNICATION MODULES
LAN dongle
PXWIRWFC
Wireless PIR detector with
camera
INSTALLER
CAME CLOUD
Switch
Modem router
Touchscreen
Home Automation
system
CAME Domotic 3.0
• LAN
• INTERNET
• RS485 bus
• PSTN line
• Internal connection
• Wireless connection
• WIFI connection
47
LAN CARDS
All the control units in the Proxinet series feature a built-in RS232 port. The PXLAN LAN interface, which allows the control
unit to be connected to the network, can be connected to this.
In addition to ensuring the connection to a LAN, the PXWEB card, equipped with Web Server, allows users to connect any
device with a web browser as a PC or handheld computer to the control unit and download a control screen consisting of a
virtual keypad with the same functions as a local keypad.
The PXWEB and PXLAN cards also allow Proxinet control units to be connected to the Came Domotic 3.0 home automation
system via LAN. This makes it possible to achieve seamless integration between the two systems and control them both
via touchscreen terminals or using portable devices equipped with the Came Domotic app. All with the aid of graphic maps
available on both the terminals and the app.
The home automation system server to which the terminals and portable devices are connected is constantly informed about
the status of the control unit inputs and outputs. It is therefore possible to use programmable logics to set actions on the home
automation system when events occur in the security system (e.g. turn on the garden lights when an external barrier detects
an intrusion, or lock the temperature control of a thermal zone when a window with a magnetic contact is opened).
Whilst perfectly integrated with each other, the systems remain compliant with the respective product and system standards.
COMMUNICATION MODULES
The control unit can also be connected to the home automation system via the PXGPRS module and PXDGETH LAN or PXDGWF
WIFI dongle, as explained in the relevant chapter.
LAN CARDS
48
ITEM
CODE
DESCRIPTION
PXLAN
64380090
LAN interface. This enables the control unit to be connected to a LAN and via this system to
the Came Domotic 3.0 home automation system. It also allows programming operations via
a PC equipped with PXManager software. Current draw 85 mA. Dimensions 75 x 45 x 20
mm Regulatory compliance: EN 50131-3 Grade 2 Environmental Class II.
PXWEB
64380110
LAN interface with web server. In addition to the features described for the PXLAN interface,
it allows a remote PC with a web browser to be connected to the control unit via the internet.
Once online with the control unit, it is possible to download a control screen consisting of
a virtual keypad with the same functions as a local keypad onto remote PC from the web
server. Current draw 85 mA. Dimensions 75 x 45 x 20 mm Regulatory compliance: EN
50131-3 Grade 2 Environmental Class II.
Example of installation
Touchscreen
VIDEO ENTRY SYSTEM
Tablet
PXLAN - PXWEB
LAN interface
COMMUNICATION MODULES
Switch
Local PC
VIDEO ENTRY SYSTEM
VIDEO ENTRY SYSTEM
HOME AUTOMATION
SERVER
Home automation
modules
• LAN
• Internal connection
• Standard connection
• Home automation BUS cable
• WIFI connection
49
INTERFACE CARDS FOR KNX SYSTEMS
The PXKNX interface card greatly expands the communication possibilities of Proxinet control units, enabling them to
communication systems featuring the KNX protocol. PXKNX connects to the RS232 port on all Proxinet control units and
supports the following communication functions:
ALERTS
COMMANDS
• Armed status for security areas
• Alarm status for security areas
• General burglar alarm status
• Arming enabling status for individual areas
• Burglar alarm memory
• Network malfunction
• Battery malfunction
• Tampering status
• Input status alert
• Output status alert
• event state message
• Total arming/disarming commands
• Arming/disarming commands for areas
• Activation/deactivation commands for burglar alarm
outputs
• Running alarm scenarios through KNX scenarios
COMMUNICATION MODULES
Minimum event duration for correct transfer to KNX bus
greater than 3 sec.
The following additional communication ports are also available:
• USB port for connecting to a PC in order to perform programming with the PXManager software (in this case, the connection
between the control unit and PC is direct and can take place using a simple USB cable).
• Second RS232 port that replicates the RS232 port on the control unit and allows the connection of additional communication
cards (e.g. connection of PXWEB LAN interface card).
50
N.B. KNX project for ETS available on the Bpt website.
KNX CARDS
ITEM
CODE
DESCRIPTION
PXKNX
64440211
KNX interface. This makes it possible to connect the control unit to systems featuring the
KNX protocol. Current draw 20 mA. Current draw from KNX bus 10 mA.
Dimensions 74 x 46 x 20 mm Regulatory compliance: EN 50131-3 Grade 2 Environmental
Class II.
Example of installation
PXKNX
COMMUNICATION MODULES
KNX interface card
Local PC
to the KNX system
• RS232
• KNX system
• USB
N.B.
For all details about programming, please contact the service centre.
51
WIRELESS DEVICES
The Proxinet36, Proxinet76 and Proxinet192 control units can also be expanded in wireless mode. By connecting one or
more PXWRX receivers to the control unit RS485 bus line, it is possible to enable the radio inputs on the control unit to use
PXWCOB/M wireless volumetric and perimeter detectors radio. It is also possible to use PXWRC, remote controls. PXWKTN/B
wireless keypads (in combination with wired keypads) and PXWSE wireless sirens. As shown in the diagram, more than one
wireless receiver can be installed on the bus, in order to improve the dialogue between the wireless devices and the control
unit. The number of wireless devices that can be used depends on the control unit used as shown in the table below.
WIRELESS DEVICES
Transmission is dual band (433 MHz and 868 MHz) and two-way. The detector transmits the alarm signal on the 868 MHz
band, the control unit sends the response that it has been received to the detector. If the detector does not receive the
response signal, it transmits the alarm signal a second time using the 433 MHz band.
With a transmission algorithm of this type, used by various devices in the wireless range, the dialogue between the control
unit and the relative devices is precise and highly reliable, unlike the one-way transmissions without no signal of receipt,
which necessarily leave the transmission of the alarm signal to the control unit to chance.
The system is also supervised. The detector transmits the signal of presence in life at regular
and set intervals during the programming phase; in case of non-receipt, after a preset time the control unit generates an alarm
signal. The detectors also transmit the battery status signal, displayed on the control unit.
The radio range is about 100 m with no obstacles and in the total absence of interference on the band. It can see significant
reductions indoors, due to the location in relation to the structure of the environment and/or due to disturbance on the radio
band.
CONTROL UNITS
64300081
64300091
64300111
WIRELESS INPUTS
16
40
64
PXWRX MODULES
2
8
16
DESCRIPTION
PXWRX REMOTE CONTROL
8
32
32
* WIRED KEYPADS
1
1
1
* PXWKTN - PXWKTB WIRELESS KEYPADS
3
7
15
PXWSE SIRENS
2
4
8
*At least one wired PXKD - PXKTN - PXKTB LCD keypad must be included.
The remaining ones can be wireless and wired, chosen from the various models.
52
RECEIVERS
ITEM
CODE
DESCRIPTION
PXWRX
64380160
Wireless receiver. Connected on the RS485 bus line of Proxinet36, Proxinet76 and
Proxinet192 control units, it allows dialogue with wireless devices. Two-way dual band radio
transmission. GFSK modulation. Current draw 100 mA. Dimensions 110 x 80 x 25 mm
Regulatory compliance: EN 50131-5-3 Grade 2 Environmental Class II, R&TTE Directive
99/05 EC. It can also be used with the ProxinetW control unit (maximum 2 units) in order to
improve the range of the unit itself.
VOLUMETRIC DETECTORS FOR INDOOR USE
ITEM
CODE
DESCRIPTION
PXWIR01
64340191
Wireless infrared volumetric detector. Range 15 m, opening 110°. Sensitivity can be adjusted
using a dip switch. It can be used with the PROXINET W2 wireless control unit and with
the PROXINET 36, PROXINET 76 and PROXINET 192 control units featuring the PXWRX
receiver connected to the bus. Two-way dual band radio transmission. GFSK modulation.
Powered by 1 x CR123A lithium battery
Battery life with average use, approximately 2 years. Dimensions 89 x 52 x 39 mm
Regulatory compliance: EN 50131-5-3 Grade 2 Environmental Class II, R&TTE Directive
99/05 EC.
ITEM
CODE
DESCRIPTION
PXWCOB01
64340211
PXWCOM01
64340221
Wireless perimeter detector. Suitable for protecting doors and windows. It features two
auxiliary inputs for the transmission of the alarm signal coming from external devices.
Each input can be programmed, by means of special dip switches, to work with
NC contacts or with shutter movement detectors (pulse counter function). It can be used
with
the Proxinet W2 wireless control unit and with the Proxinet36, Proxinet76 and Proxinet192
control units featuring
the PXWRX receiver connected to the bus. Wireless transmission on three channels - dual
band,
two-way. GFSK modulation. Powered by 1 x CR123A lithium battery. Battery life with
average use, approximately 3 years. Dimensions 28 x 95 x 28 mm Regulatory compliance:
EN 50131-2-6, EN 50131-5-3 Grade 2 Environmental Class II, R&TTE Directive 99/05 EC.
White.
Wireless perimeter detector. Brown.
(Features as PXWCOB01).
WIRELESS DEVICES
PERIMETER DETECTORS
PXWIR01
Diagram
TOP WIEV
70°
2,5
2
m
1,5
1
0,5
m
0,5 1 1,5 2 2,5 3 3,5 4 4,5 5 5,5 6 6,5 7 7,5 8 8,5 9 9,5 10
53
DETECTORS WITH CAMERA
PXWIRFC and PXWIRWFC are passive infrared detectors with built-in camera for video verification. Following the detection of
an intrusion, they make it possible to generate and transmit a series of images or a video clip to the control unit, as explained
below.
PXWIRFC. Following an alarm, the detector transmits its signal to the control unit using the dual band 868.65 MHz and 433.92
MHz two-way radio transmission, available for all the system’s wireless devices. If armed, the control unit sends a consensus
to the detector to activate the built-in camera. The detector then transmits the image obtained to the control unit using
wireless transmission on the 868.65 MHz frequency. The camera has QVGA resolution
(320 x 240) and it is possible to transmit up to 5 images for each alarm event. As an alternative to the images, a 2 fps video
lasting 3 seconds can be generated and transmitted.
The control unit must be equipped with a PXGPRS module, which allows image storage on the CAME Cloud and users are sent
a notification telling them to connect to the Cloud to view the images.
PXWIRWFC. Operation is similar to that described for the previous model, with the difference that the image is transmitted
via WIFI technology, thanks to a special built-in transmitter. This can significantly improve transmission by reducing latency
times. If the detector is unable to reach the control unit via the WIFI channel, the image is transmitted using the transmission
frequency of 868.65 MHz, thus ensuring system functionality. The camera has resolution that can be selected from QVGA
(320 x 240) or VGA (640 x 480) and it is possible to transmit up to 20 QVGA or 10 VGA images for each alarm event. As an
alternative to the images, a 2 fps video lasting 10 seconds can be generated and transmitted (with QVGA resolution).
The control unit must be equipped with a PXGPRS module with relative PXDGWF WIFI dongle. Once again in this case, users
receive a notification telling them to connect to the Cloud to view the images. In both cases, if the connection to the Cloud is
not envisaged, it is possible to send an MMS or an e-mail containing images of the event.
At any time and remotely, users can send a text massage to generate and receive images or video clips.
WIRELESS DEVICES
The detectors with camera incorporate an IR illuminator for shooting in dark conditions.
DETECTORS WITH CAMERA
54
ITEM
CODE
DESCRIPTION
PXWIRFC
64340440
PXWIRWFC
64340450
Wireless passive infrared detector with camera. Range 23 m, opening 110°. In the event
of an alarm, it allows you to generate and transmit a series of images or a video clip to the
control unit. Complete with IR illuminator for shooting in dark conditions. It can be used with
the Proxinet W2 wireless control unit and with the Proxinet36, Proxinet76 and Proxinet192
control units featuring
the PXWRX receiver connected to the bus. Two-way dual band radio transmission. GFSK
modulation. Powered by 3 x CR123A lithium batteries (or by an external power supply with
micro-USB connector). Battery life with average use, approximately 2 years. Dimensions 89
x 52 x 39 mm Regulatory compliance: EN 50131-2-2, EN 50131-5-3 Grade 2 Environmental
Class II, R&TTE Directive 99/05 EC.
Wireless passive infrared detector with camera and WIFI transmitter. Range 23 m, opening
110°. In the event of an alarm, it allows you to generate and transmit a series of images
or a video clip to the control unit via a WIFI connection. Complete with IR illuminator for
shooting in dark conditions. It can be used with the Proxinet W2 wireless control unit and
with the Proxinet 36, Proxinet 76 and Proxinet 192 control units featuring the PXWRX
receiver connected to the bus. Two-way dual band radio transmission. GFSK modulation.
Powered by 3 x CR123A lithium batteries (or by an external power supply with micro-USB
connector). Battery life with average use, approximately 2 years. Dimensions 89 x 52 x 39
mm Regulatory compliance: EN 50131-2-2, EN 50131-5-3 Grade 2 Environmental Class II,
R&TTE Directive 99/05 EC.
Example of installation
MMS
MMS MESSAGE
CAME CLOUD
CAME CLOUD
Smartphone
E-MAIL
E-MAIL
Telephone
sms
PXGPRS
GPRS module
Smartphone
PXDGWF
WIFI dongle
TRA
NSM
NV
IA W
WIRELESS DEVICES
GE
IMA
IO
ISS
IFI
PXWIRWFC
Detector with camera
ALARM
ALARM
• RS485 bus
• PSTN line
• Internal connection
• Wireless connection
• WIFI connection
PXWIRFC - PXWIRWFC
Diagram
TOP WIEV
110°
m
2,25
2
1,5
1
0,5
m
1
TOP WIEV
90°
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23
m
2,25
6,40
2
65°
1,5
1
0,5
CAMERA
m
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23
55
WIRELESS DEVICES
CURTAIN-EFFECT DETECTORS
56
ITEM
CODE
DESCRIPTION
PXWIRCB
64340380
PXWDTCB
64340390
PXWDTCM
64340410
Wireless passive infrared curtain-effect detector. Ceiling installation (indoors or outdoors if
protected) or laterally (indoors only). Particularly suitable for protecting doors and windows.
Circuit to differentiate the crossing direction (the user can cross the entrance from the inside
outwards without triggering the alarm, while an intruder coming in from outside is detected
as normal). It features two auxiliary inputs for the transmission of the alarm signal coming
from external devices. Each input can be programmed, using special dip switches, to work
with NC contacts or shutter motion detectors (pulse count function). It can be used with the
Proxinet W2 wireless control unit and with the Proxinet 36, Proxinet 76 and Proxinet 192
control units featuring the PXWRX receiver connected to the bus. Wireless transmission on
three channels - dual band, two-way. GFSK modulation. Powered by 1 x 3 V CR123A lithium
battery. Battery life with average use, approximately 2 years. IP43 protection rating.
Dimensions: 151 x 30 x 38 mm. Regulatory compliance: EN 50131-2-2 Grade 2
Environmental Class III, R&TTE directive 99/05/EC. White.
Dual technology wireless curtain-effect detector, made with passive infrared section and
microwave section. Ceiling installation (indoors or outdoors if protected) or laterally (indoors
only). Particularly suitable for protecting doors and windows. Circuit to differentiate the
crossing direction (the user can cross the entrance from the inside outwards without
triggering the alarm, while an intruder coming in from outside is detected as normal). It
features two auxiliary inputs for the transmission of the alarm signal coming from external
devices. Each input can be programmed, using special dip switches, to work with NC
contacts or shutter motion detectors (pulse count function). It can be used with the Proxinet
W2 wireless control unit and with the Proxinet 36, Proxinet 76 and Proxinet 192 control units
featuring the PXWRX receiver connected to the bus. Wireless transmission on three channels
- dual band, two-way. GFSK modulation. Powered by 1 x 3 V CR123A lithium battery.
Battery life with average use, approximately 2 years. IP43 protection rating. Dimensions:
151 x 30 x 38 mm. Regulatory compliance: EN 50131-2-4 Grade 2 Environmental Class III,
R&TTE directive 99/05/EC. White.
Dual technology wireless curtain-effect detector, made with passive infrared section and
microwave section. Brown.
(Features as PXWDTCB).
PXWDTCL
64340360
Dual technology wireless curtain-effect detector, made with dual passive infrared section
and microwave section. Range 3 m opening 28° adjustable. Protected indoor and outdoor
installation. Particularly suitable for protecting doors and windows. It can be used with the
Proxinet W2 wireless control unit and with the Proxinet 36, Proxinet 76 and Proxinet 192
control units featuring the PXWRX receiver connected to the bus. Two-way dual band radio
transmission. GFSK modulation. Powered by 2 x CR123A lithium batteries. Battery life with
average use, approximately 2 years. Dimensions: 330 x 40 x 30 mm.
Operating temperature -40 to +70 °C. Regulatory compliance: R&TTE directive 99/05 EC.
Diagrams
5m
2.5 m
PXWDTCB - PXWDTCM
PXWIRCB
PXWIRCB
PXWDTCB
PXWDTCM
Diagrams
3m
4m
0.5 m
1.2 m
WIRELESS DEVICES
PXWIRCB
PXWDTCB
PXWDTCM
Diagrams
1.5 m
2.5 m
PXWIRCB
Diagrams
0.15 m
2.2 m
1.2 m
0.30 m
0.15 m
PXWDTCL
Diagrams
SHORT RANGE
1.2 m
3m
LONG RANGE
1.5 m
0.3 m
0.8 m
0.2 m
57
DETECTORS FOR OUTDOOR USE
ITEM
CODE
DESCRIPTION
PXWDTVE
64340370
Dual technology wireless volumetric detector. Made with two detection heads, one passive
infrared and one microwave, operating in AND logic, individually adjustable to achieve
the best coverage. Range 12 m opening 80° with 5 beams on 1 floor. The range of both
heads can be adjusted using trimmers and dip switches. Installation outdoors on the wall
or on a post, particularly suitable for protective outdoor volumes. Two-way dual band radio
transmission. GFSK modulation. Powered by 2 x CR123A lithium batteries. Battery life with
average use, approximately 2 years. IP54 protection rating. Dimensions 190 x 85 x 75 mm
Operating temperature -40 to +70 °C. Regulatory compliance: R&TTE directive 99/05 EC.
PXWDTVE
Diagram
TOP WIEV
100°
m
2,5
NO ALARM
2
1,5
NO ALARM
1
ALARM
0,5
m
WIRELESS DEVICES
12 m
58
1
2
3
4
5
6
7
8
9
10 11 12
CONTROL DEVICES
ITEM
CODE
DESCRIPTION
PXWRC
64320021
PXWKTN
64320080
PXWKTB
64320070
Two-way remote control. It allows system control through the launch of 3 scenarios
(programmed partitions e.g. “NIGHT” scenario, arming of perimeter area, outdoor area, day
area). It shows the system status signals and the scenario activated. It can be used with
the Proxinet W2 wireless control unit and with the Proxinet 36, Proxinet 76 and Proxinet
192 control units featuring the PXWRX receiver connected to the bus. Two-way wireless
transmission (868 MHz), GFSK modulation. Powered by 1 x CR2032 lithium battery. Battery
life with average use, approximately 2 years. Dimensions 38 x 76 x 9 mm Regulatory
compliance: EN 50131-5-3 Grade 2 Environmental Class II, R&TTE Directive 99/05 EC.
Backlit wireless capacitive LCD keypad with touch-sensitive keys. It allows total system
control through the launch of 16 scenarios (programmed partitions e.g. “NIGHT” scenario,
arming of perimeter area, outdoor area, day area). It features a transponder key reader
to use with PXTAG key. It can be used with the Proxinet W2 wireless control unit and
with the Proxinet 36, Proxinet 76 and Proxinet 192 control units featuring the PXWRX
receiver connected to the bus. Two-way dual band radio transmission, GFSK modulation.
Powered by 3 x CR123A lithium batteries. Battery life with average use, approximately 2
years. Dimensions 158 x 138 x 31 mm Regulatory compliance: EN 50131-5-3 Grade 2
Environmental Class II, R&TTE Directive 99/05 EC. Black.
Backlit wireless capacitive LCD keypad with touch-sensitive keys. White.
(Features as PXWKTN).
ITEM
CODE
DESCRIPTION
PXWSE
64420050
Wireless self-powered siren for outdoor use. Polycarbonate container. Sound power 101 dB
at 1 m. High-efficiency LED flasher. It can be used with the Proxinet W2 wireless control unit
and with the Proxinet 36, Proxinet 76 and Proxinet 192 control units featuring the PXWRX
receiver connected to the bus. Two-way dual band radio transmission, GFSK modulation.
Powered by 5 x CR123A lithium batteries. Battery life with average use, approximately 2
years. Operating temperature -25 to +55 °C. IP34 protection rating. Dimensions 217 x 302 x
107 mm Regulatory compliance: EN 50131-4, EN 50131-5-3 Grade 2 Environmental Class
III, R&TTE Directive 99/05 EC.
WIRELESS DEVICES
SIRENS
59
Example of installation
PXWIRFC
IR detector with
camera
PXWSE
Wireless siren for
outdoor use
PXWRC
Remote control
PXWKTN
Wireless keypad
PXWRX
PXWCOB/M01
Wireless receiver
WIRELESS DEVICES
Wireless
perimeter
detector
PXWIR01
Wireless
volumetric detector
PXWRC
Remote control
PXKTN
Wired keypad
PXWDTCB
DT curtain wireless
detector
PXWDTVE
DT wireless detector
for outdoor use
PXWRX
Wireless receiver
PXWDTCL
DT curtain wireless
detector
• RS485 bus
• Wireless connection
60
PX8IR
Expansion module
with 8 inputs
Example of installation
PXWDTCL
DT curtain wireless
detector
PXWSE
Wireless siren for
outdoor use
PXWRC
Remote control
PXWKTN
Wireless keypad
PXWCOB/M01
WIRELESS DEVICES
Wireless
perimeter
detector
PXWIR01
Wireless
volumetric detector
PXWDTCB
DT curtain wireless
detector
PXWDTVE
DT wireless detector
for outdoor use
PXWIRFC
IR detector with
camera
• Wireless connection
61
VOLUMETRIC DETECTORS
FOR INDOOR USE
VOLUMETRIC DETECTORS FOR INDOOR USE
WALL-MOUNTED DETECTORS
ITEM
CODE
DESCRIPTION
PXIRV
64340260
Passive infrared volumetric detector made with dual PIR element. Range 15 m opening
90° with 18 beams on 4 floors. Range regulation via dip switch. Featuring alarm memory
circuit. TC input for detector inhibition when control unit is off. Complete with articulated joint.
Current draw 17 mA. Dimensions: 107 x 61,5 x 44 mm. Regulatory compliance: EN 501312-2 Grade 2 Environmental Class II.
PXDTV
64340270
Dual technology wireless detector, made with passive infrared section and microwave
section. Range 15 m opening 90° with 18 beams on 4 floors. Microwave section range
regulation via dimmer. Featuring alarm memory circuit. TC input for detector inhibition when
control unit is off. Complete with articulated joint. Current draw 22 mA. Dimensions 107 x
61.5 x 44 mm Regulatory compliance: EN 50131-2-4 Grade 2 Environmental Class II.
PXDTAM
64340280
Dual technology wireless detector, made with passive infrared section and microwave
section. Operation of the two sections in AND or OR logic, selectable using dip switches.
Anti-blinding function of infrared section (the alarm is generated if detections occur on the
microwave section and not on the infrared section). Anti-masking function of microwave
section indicated by
special relay output. Range 15 m opening 90° with 18 beams on 4 floors. Sensitivity
adjustment of both sections via dip switch. Microwave section range regulation via dimmer.
Featuring alarm memory circuit. TC input for detector inhibition when control unit is off.
Complete with articulated joint. Current draw 34 mA. Dimensions 107 x 61,5 x 44 mm
Regulatory compliance: EN 50131-2-4 Grade 2 Environmental Class II.
PXIRV
Diagram
m
TOP WIEV
90°
1,9
3,3
5,9
2
1,5
1
0,5
m
10.5 m
0
10.5 m
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15
PXDTV - PXDTAM
Diagram
m
TOP WIEV
90°
1,9
3,3
6,9
2
1,5
1
0,5
m
10.5 m
62
0
10.5 m
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15
RECESSED DETECTORS
DESCRIPTION
Passive infrared volumetric detector. Range 10 m opening 140° with beams on 3 floors.
Sensitivity adjustment via pulse counters. Featuring alarm memory circuit. Current draw 9
mA. Operating temperature -5 to +45 °C.
Dimensions: 1 x recessed wiring series module.
AVE
IPIAB
64345600
For AVE Blanc wiring series.
BTICINO
IPIXA
64343800
For BTICINO Axolute grey wiring series.
IPIXN
64343900
For BTICINO Axolute black wiring series.
IPITL
64340800
For BTICINO Light wiring series.
IPITT
64343600
For BTICINO Light Tech wiring series.
IPILV
64340600
For BTICINO Living wiring series.
IPILI
64340500
For BTICINO Living International wiring series.
IPIMA
64340700
For BTICINO Magic wiring series.
IPIXB
64340160
For BITICINO Axolute white wiring series.
IPITM
64340170
For BITICINO Matix white wiring series.
IPITB
64340180
For BITICINO Magic TT light beige wiring series.
IPIGB
64340300
For civil series GEWISS System white.
IPICT
64345500
For GEWISS Chorus titanium wiring series.
IPIGP
64340400
For GEWISS Playbus wiring series.
IPIGN
64344100
For GEWISS System black wiring series.
IPICB
64340120
For GEWISS Chorus white wiring series.
IPICN
64340130
For GEWISS Chorus black wiring series.
VOLUMETRIC DETECTORS
GEWISS
63
RECESSED DETECTORS
DESCRIPTION
Passive infrared volumetric detector. Range 10 m opening 140° with beams on 3 floors.
Sensitivity adjustment via pulse counters. Featuring alarm memory circuit. Current draw 9
mA. Operating temperature -5 to +45 °C.
Dimensions: 1 x recessed wiring series module.
LEGRAND
IPILC
64344000
For LEGRAND Cross wireless series.
VIMAR
IPIVE
64344300
For VIMAR Eikon anthracite grey wiring series.
IPIVB
64340900
For VIMAR Idea white wiring series.
IPIVN
64341000
For VIMAR Idea black wiring series.
IPIVP
64343700
For VIMAR Plana wiring series.
IPIVX
64340140
For VIMAR Eikon Next silver wiring series.
IPIVA
64340150
For VIMAR Eikon white wiring series.
VOLUMETRIC DETECTORS
Diagram for all recessed
volumetric detectors
m
TOP WIEV
140°
3
2
2
1,5
1
0,5
5m
0
5m
1
2
3
4
5
6
7
8
9
10
CURTAIN-EFFECT DETECTORS
64
ITEM
CODE
DESCRIPTION
PXDTCI
64340250
PXDTC01
64340420
Dual technology curtain-effect detector, made with passive infrared section and microwave
section. Range 6 m. The range can be adjusted using trimmers and dip switches. Protected
indoor and outdoor installation. Particularly suitable for protecting doors and windows.
Featuring alarm memory circuit. TC input for detector inhibition when control unit is off.
Current draw 27 mA. Dimensions 87 x 32 x 35 mm Regulatory compliance: EN 50131-2-4
Grade 2 Environmental Class III.
Dual technology curtain-effect detector, made with passive infrared section and microwave
section. Anti-masking function of both sections indicated by a special relay output. Range
8 m The range can be adjusted using trimmers and dip switches. Protected indoor and
outdoor installation. Particularly suitable for protecting doors and windows. When used with
the PXDTCP shutter, it is immune to small animals. Featuring alarm memory circuit. TC input
for detector inhibition when control unit is off. Complete with angle bracket for wall mounting
on the right or left side. Current draw 32 mA. IP61 protection rating.
Dimensions 110 x 44 x 41 mm Regulatory compliance: EN 50131-2-4 Grade 2
Environmental Class III.
CURTAIN-EFFECT DETECTORS
CODE
DESCRIPTION
PXDTCS
64380180
PXDTCP
64380190
Articulated joint for PXDTC01 and PXDTCE detectors. It allows you to direct the detector and
optimise the coverage area.
Shutter for PXDTC01 and PXDTCE detectors. Installed on the lens, this makes it possible to
exclude the lower protective beams in order to avoid detecting small animals in the coverage
area.
VOLUMETRIC DETECTORS
ITEM
PXDTCI
Diagram
m
TOP WIEV
100°
0,8
0,4
2.5 m
0
2.5 m
m
0
1
2
3
4
5
m
PXDTC01
Diagram
2
1
TOP WIEV
0
1
1
2
0
3
1
4
m
1
2
3
4
5
6
7
8
65
VOLUMETRIC DETECTORS
FOR OUTDOOR USE
CURTAIN-EFFECT DETECTORS
ITEM
CODE
DESCRIPTION
PXDTCE
64340430
Dual technology curtain-effect detector, made with passive infrared section and microwave
section. Anti-masking function of both sections indicated by a special relay output. Range
12 m The range can be adjusted using trimmers and dip switches. Installation indoors and
outside, particularly suitable for protecting exterior facades. When used with the PXDTCP
shutter, it is immune to small animals. Featuring alarm memory circuit. TC input for detector
inhibition when control unit is off. Complete with angle bracket for wall mounting on the right
or left side and rain canopy. Current draw 32 mA. IP65 protection rating. Dimensions 110 x
44 x 42 mm Regulatory compliance: EN 50131-2-4. Grade 2, Environmental Class IV.
ITEM
CODE
DESCRIPTION
PXIRVE
64340340
Passive infrared volumetric detector. Made with two detection heads, adjustable individually
to achieve the best coverage. Possibility of operation of the two heads in AND OR logic.
Range 12 m opening 100° with 10 beams for each detection head. The range can be
adjusted using dip switches. Installation outdoors on the wall or on a post, particularly
suitable for protective outdoor volumes. Current draw 100 mA. Operating temperature -40 to
+70 °C. IP54 protection rating.
Dimensions 190 x 85 x 75 mm
PXDTVE
64340350
Dual technology volumetric detector. Made with two detection heads, one passive infrared
and one microwave, operating in AND logic, individually adjustable to achieve the best
coverage. Range 12 m opening 80° with 5 beams on 1 floor. The range of both heads
can be adjusted using trimmers and dip switches. Installation outdoors on the wall or on a
post, particularly suitable for protective outdoor volumes. Current draw 50 mA. Operating
temperature -40 to +70 °C. IP54 protection rating.
Dimensions 190 x 85 x 75 mm
VOLUMETRIC DETECTORS FOR OUTDOOR USE
WALL-MOUNTED DETECTORS
PXIRVE
Diagram
m
TOP WIEV
100°
NO ALARM
2,5
2
ALARM
1,5
1
NO ALARM
0,5
m
10 m
PXDTVE
Diagram
0
TOP WIEV
100°
10 m
1
2
3
4
5
6
7
8
9
10 11 12
m
2,5
NO ALARM
2
1,5
NO ALARM
1
ALARM
0,5
m
12 m
PXDTCE
Diagram
1
2
3
4
5
6
7
8
9
10 11 12
m
2
1
TOP WIEV
0
1
1
2
0
3
1
4
m
1
66
2
3
4
5
6
7
8
9
10 11 12
PERIMETER DETECTORS
MAGNETIC CONTACTS
ITEM
CODE
DESCRIPTION
CSP01
64386700
CSP02
64386800
Magnetic contact for surfaces. Plastic container. NC contact connection via internal
terminals. Operating distance 15 mm. Dimensions: REED contact 60 x 17 x 13 mm; Magnet:
60 x 13 x 13 mm. Regulatory compliance: EN 50131-2-6, Grade 2, Environmental Class I.
White.
Magnetic contact for surfaces. Plastic container. NC contact connection via internal
terminals. Operating distance 15 mm. Dimensions: REED contact 60 x 17 x 13 mm; Magnet:
60 x 13 x 13 mm. Regulatory compliance: EN 50131-2-6, Grade 2, Environmental Class I.
Brown.
CSP21
64386900
CXP31
64387600
CIO21
64387000
CIO23
64387100
Recessed magnetic contact. Brass container with knurled body. Connection via 4 wires, 2 to
prevent tampering and 2 for the NC contact, 30 cm long. Operating distance 10 mm.
Dimensions: REED contact 30 x 7,6 mm; magnet: 19.5 x 7.6 mm; fixing diameter 8 mm.
Regulatory compliance: EN 50131-2-6, Grade 2, Environmental Class IV.
CIO22
64387200
Recessed magnetic contact. Brass container with smooth body. Connection to NC contact
via 2 wires, 30 cm long. Operating distance 12 mm. Operating temperature -40 to +125 °C.
Dimensions: REED contact 22 x 7.5 mm; magnet: 22 x 7.5 mm; fixing diameter 8 mm.
CSPM02
64380210
Miniature magnetic contact for surfaces. Aluminium container. Connection via 4 wires, 2 to
prevent tampering and 2 for the NC contact, 30 cm long. Operating distance 10 mm.
Dimensions: REED contact 25 x 6 x 6 mm; magnet: 25 x 6 x 6 mm.
Regulatory compliance: EN 50131-2-6, Grade 2, Environmental Class IV.
CSP60
64380220
Miniature magnetic contact for surfaces. Aluminium container. Connection via 4 wires, 2 to
prevent tampering and 2 for the NC contact, 30 cm long. Operating distance 18 mm.
Dimensions: REED contact 32 x 15 x 8 mm; magnet: 32 x 15 x 18 mm.
Regulatory compliance: EN 50131-2-6, Grade 2, Environmental Class IV.
PERIMETER DETECTORS
Magnetic contact for surfaces. Plastic container. Connection via 4 wires, 2 to prevent
tampering and 2 for the NC contact, 30 cm long. Operating distance 18 mm.
Dimensions: REED contact 32 x 8 x 13 mm; magnet 32 x 8 x 13 mm. Regulatory
compliance: EN 50131-2-6, Grade 2, Environmental Class IV. White.
Magnetic contact for surfaces. Plastic container. Connection to NC contact via 2 wires, 1 m
long. Operating distance 40 mm. REED contact dimensions 60 x 5 x 16 mm; magnet:
60 x 5 x 16 mm. Regulatory compliance: EN 50131-2-6, Grade 2, Environmental Class II.
White.
Recessed magnetic contact. Brass container with knurled body. Connection via 4 wires, 2 to
prevent tampering and 2 for the NC contact, 30 cm long. Operating distance 10 mm.
Dimensions: REED contact 15 x 6 mm; magnet: 15 x 6 mm; fixing diameter 6 mm.
Regulatory compliance: EN 50131-2-6, Grade 2, Environmental Class IV.
MAGNETIC CONTACTS FOR DOORS AND FIXTURES IN FERROUS MATERIAL
ITEM
CODE
DESCRIPTION
CSA31
64387800
CSA11
64387300
Magnetic contact for surfaces. Aluminium container. Connection via 4 wires, 2 to prevent
tampering and 2 for the NC contact, 120 cm long. Operating distance 22 mm. Dimensions:
REED contact 80 x 18 x 18 mm; magnet: 80 x 18 x 18 mm.
Regulatory compliance: EN 50131-2-6, Grade 2, Environmental Class IV.
Magnetic contact for surfaces. Aluminium container. NC contact connection via internal
terminals. Operating distance 22 mm. Dimensions: REED contact 80 x 18 x 18 mm; magnet:
80 x 18 x 18 mm. Regulatory compliance: EN 50131-2-6, Grade 2, Environmental Class II.
CIP31
64387500
Recessed magnetic contact. Plastic container. Connection via 4 wires, 2 to prevent
tampering and 2 for the NC contact, 30 cm long. Operating distance 10 mm. Dimensions:
REED contact 28 x 20 mm; magnet: 28 x 20 mm; fixing diameter 18 mm. Regulatory
compliance: EN 50131-2-6, Grade 2, Environmental Class IV.
67
SPECIAL MAGNETIC CONTACTS
ITEM
CODE
DESCRIPTION
CPA31
64387700
CSA12
64387400
Magnetic contact for overhead doors. Aluminium container. Connection via 4 wires, 2 to
prevent tampering and 2 for the NC contact, in metal sheath, 1.5 m long. Operating distance
25 mm. Dimensions: REED contact 130 x 42 x 15 mm; magnet: 98 x 30 x 25 mm.
Regulatory compliance: EN 50131-2-6, Grade 2, Environmental Class IV.
Double balancing safety magnetic contact for surfaces. Aluminium container. Connection via
4 internal terminals, 2 to prevent tampering and 2 for the NC contact. Operating distance 10
mm. Dimensions: REED contact 120 x 37 x 27 mm; magnet: 120 x 37 x 27 mm. Regulatory
compliance: EN 50131-2-6, Grade 3, Environmental Class IV.
PERIMETER DETECTORS
VIBRATION AND MOTION DETECTORS
ITEM
CODE
DESCRIPTION
CAS01
64345700
Shutter motion rod detector. Plastic container. Connection via 3 wires (C-NO-NC contact),
10 cm long. Dimensions 55 x 57 x 31 mm Rod length 330 mm.
CFSST
64341900
Wired shutter motion detector. Plastic container. Connection via two wires. Operating
temperature -5 to +40 °C. Dimensions 93 x 85 x 10 mm. Rope length 3 m. Requires the
SAC01 analysis card.
CFSST02
64340290
Shutter motion rope detector. Plastic container. Steel sliding pulley. Connection via terminals.
Operating temperature -5 to +50 °C. Dimensions: 102 x 90 x 14 mm. Rope length 2.8 m.
Requires the SAC01 analysis card.
RRV14
64342200
Volumetric glass break detector. Plastic container. Range 14 m Current draw 14 mA.
Operating temperature -10 to +60 °C. Dimensions 29 x 52 x 89 mm.
CFI02
64345900
Shutter motion rope detector with built-in analysis card. Plastic container. Connection via 4
wires, 2 for powering the device and 2 for alarm contact, 1 m long. Current draw 100 uA.
Operating temperature -5 to +50 °C. Dimensions: 102 x 98 x 16 mm. Rope length 2.9 m.
RVB01
64346000
Piezoelectric vibration detector. Plastic container. Connection via terminals. Particularly
suitable for protecting doors and windows. Adjusting amperometric sensitivity. Current draw
20 mA. Operating temperature 0 to +55 °C. Dimensions 86 x 21 x 25 mm.
RIN01
64346200
CIS03
64340330
Gold bar vibration detector. Plastic container. Connection via 4 wires, 2 to prevent tampering
and 2 for the NC contact, 90 cm long. Particularly suitable for protecting glass surfaces.
Coverage range on glass 2.5 m. Operating temperature -5 to +50 °C. IP55 protection rating.
Dimensions 34 x 34 x 21 mm Requires the SAC02 analysis card.
Gold bar vibration detector. Plastic container. Connection via terminals. Particularly suitable
for protecting glass, walls and surfaces in general. Coverage range on glass 2.5 m.
Operating temperature -5 to +50 °C. Dimensions 28,5 x 50 x 16 mm. Requires the SAC02
analysis card.
CEG65
64380230
Ball vibration detector for outdoor use. Painted aluminium container. Connection via 4 wires,
2 to prevent tampering and 2 for the NC contact, in metal sheath, 1 m long. Particularly
suitable for protecting gratings and fencing. Operating temperature -20 to +60 °C. IP65
protection rating. Dimensions 56 mm x 22 Ø. Requires the SAC02 analysis card.
ACCESSORIES FOR PERIMETER DETECTORS
68
ITEM
CODE
DESCRIPTION
SAC01
64340310
Analysis card for CFSST and CFSST02 detectors. This allows the connection of one or
more shutter motion detectors (max 5). Adjusting the number of pulses via jumpers and
potentiometer. Current draw 32 mA. Operating temperature -5 to +50 °C. Dimensions 77 x
57 x 20 mm.
SAC02
64340320
Balanced line analysis card for RIN01, CIS03, CEG65 detectors. This allows the connection
of one or more vibration detectors connected in series (max 5). Sensitivity adjustment via
potentiometer. Current draw 32 mA. Operating temperature -5 to +50 °C. Dimensions 76 x
57 x 20 mm.
BARRIERS
ITEM
CODE
DESCRIPTION
BI205
64360010
BI410
64360020
BI615
64360030
BI820
64360040
BI825
64360050
BI205W
64360060
BI410W
64360070
BI615W
64360080
BI820W
64360090
BI825W
64360110
BI4SD
64360120
Infrared barrier for doors and windows. Height 0.5 m with 2 detection beams each consisting
of two beams operating with AND logic (to stop the beam, it is necessary to interrupt both
the rays). It is also possible to set the AND function between two beams in order to prevent
false alarms. Wired synchronism connection between the two bars. Range: 30 m indoors;
15 m outdoors. Minimum distance between the bars 40 cm. Current draw 50 mA. Operating
temperature -10 to +65 °C. IP54 protection rating. Width 25 mm, depth 22 mm. Black.
Infrared barrier for doors and windows. Height 1 m with 4 detection beams each consisting
of two beams operating with AND logic (to stop the beam, it is necessary to interrupt both
the rays). It is also possible to set the AND function between two beams in order to prevent
false alarms. Wired synchronism connection between the two bars. Range: 30 m indoors;
15 m outdoors. Minimum distance between the bars 40 cm. Current draw 50 mA. Operating
temperature -10 to +65 °C. IP54 protection rating. Width 25 mm, depth 22 mm. Black.
Infrared barrier for doors and windows. Height 1.5 m with 6 detection beams each consisting
of two beams operating with AND logic (to stop the beam, it is necessary to interrupt both
the rays). It is also possible to set the AND function between two beams in order to prevent
false alarms. Wired synchronism connection between the two bars. Range: 30 m indoors;
15 m outdoors. Minimum distance between the bars 40 cm. Current draw 50 mA. Operating
temperature -10 to +65 °C. IP54 protection rating. Width 25 mm, depth 22 mm. Black.
Infrared barrier for doors and windows. Height 2 m with 8 detection beams each consisting
of two beams operating with AND logic (to stop the beam, it is necessary to interrupt both
the rays). It is also possible to set the AND function between two beams in order to prevent
false alarms. Wired synchronism connection between the two bars. Range: 30 m indoors;
15 m outdoors. Minimum distance between the bars 40 cm. Current draw 80 mA. Operating
temperature -10 to +65 °C. IP54 protection rating. Width 25 mm, depth 22 mm. Black.
Infrared barrier for doors and windows. Height 2,5 m with 8 detection beams each consisting
of two beams operating with AND logic (to stop the beam, it is necessary to interrupt both
the rays). It is also possible to set the AND function between two beams in order to prevent
false alarms. Wired synchronism connection between the two bars. Range: 30 m indoors;
15 m outdoors. Minimum distance between the bars 40 cm. Current draw 80 mA. Operating
temperature -10 to +65 °C. IP54 protection rating. Width 25 mm, depth 22 mm. Black.
Infrared barrier for doors and windows. Height 0,5 m with 2 detection beams each consisting
of two beams operating with AND logic (to stop the beam, it is necessary to interrupt both
the rays). It is also possible to set the AND function between two beams in order to prevent
false alarms. Wired synchronism connection between the two bars. Range: 5 m indoors; 5
m outdoors. Minimum distance between the bars 40 cm. Current draw 50 mA. Operating
temperature -10 to +65 °C. IP54 protection rating. Width 25 mm, depth 22 mm. White.
Infrared barrier for doors and windows. Height 1 m with 4 detection beams each consisting
of two beams operating with AND logic (to stop the beam, it is necessary to interrupt both
the rays). It is also possible to set the AND function between two beams in order to prevent
false alarms. Wired synchronism connection between the two bars. Range: 5 m indoors; 5
m outdoors. Minimum distance between the bars 40 cm. Current draw 50 mA. Operating
temperature -10 to +65 °C. IP54 protection rating. Width 25 mm, depth 22 mm. White.
Infrared barrier for doors and windows. Height 1,5 m with 6 detection beams each consisting
of two beams operating with AND logic (to stop the beam, it is necessary to interrupt both
the rays). It is also possible to set the AND function between two beams in order to prevent
false alarms. Wired synchronism connection between the two bars. Range: 5 m indoors; 5
m outdoors. Minimum distance between the bars 40 cm. Current draw 50 mA. Operating
temperature -10 to +65 °C. IP54 protection rating. Width 25 mm, depth 22 mm. White.
Infrared barrier for doors and windows. Height 2 m with 8 detection beams each consisting
of two beams operating with AND logic (to stop the beam, it is necessary to interrupt both
the rays). It is also possible to set the AND function between two beams in order to prevent
false alarms. Wired synchronism connection between the two bars. Range: 5 m indoors; 5
m outdoors. Minimum distance between the bars 40 cm. Current draw 80 mA. Operating
temperature -10 to +65 °C. IP54 protection rating. Width 25 mm, depth 22 mm. White.
Infrared barrier for doors and windows. Height 2,5 m with 8 detection beams each consisting
of two beams operating with AND logic (to stop the beam, it is necessary to interrupt both
the rays). It is also possible to set the AND function between two beams in order to prevent
false alarms. Wired synchronism connection between the two bars. Range: 5 m indoors; 5
m outdoors. Minimum distance between the bars 40 cm. Current draw 80 mA. Operating
temperature -10 to +65 °C. IP54 protection rating. Width 25 mm, depth 22 mm. White.
Pack of 4 brackets for infrared barriers for doors and windows. It allows the rotation of the
bars on their vertical axis, in order to achieve proper positioning (use a pack of 4 brackets for
each barrier).
BARRIERS
INFRARED BARRIERS FOR DOORS AND WINDOWS
69
BARRIERS
INFRARED BARRIERS FOR DOORS AND WINDOWS CONFIGURED FOR WIRELESS TRANSMITTERS
ITEM
CODE
DESCRIPTION
BIWB205AS
64360191
BIWB410AS
64360211
BIWB615AS
64360221
BIWB820AS
64360231
BBW219
64480060
Infrared barrier for doors and windows. Supplied with external containers for housing batteries
and the PXWCO01 perimeter detector to use as transmitter (this allows radio dialogue
between the barrier and the wireless ProxinetW2 control unit and with the Proxinet36,
Proxinet76 and Proxinet192 control units equipped with PXWRX receiver). Height 0.5 m with
2 detection beams each consisting of two beams operating with AND logic (to stop the beam,
it is necessary to interrupt both the rays). It is also possible to set the AND function between
two beams in order to prevent false alarms. Optical synchronism between the two bars with
simplified alignment system. Range: 15 m indoors; 5 m outdoors. Minimum distance between
the bars 40 cm. Alarm output with NC contact. Powered by 2 x 3.6 V 19 Ah lithium batteries
(one per bar), supplied as standard. Acoustic low battery alert. Battery duration of between 1
and 3 years. Operating temperature -10 to +65 / -40 to +70 °C. IP54 protection rating. Width
25 mm, depth 22 mm. Outer container dimensions 40 x 40 x 220 mm (-12 mm to obtain the
total height). Black.
Infrared barrier for doors and windows. Supplied with external containers for housing batteries
and the PXWCO perimeter detector to use as transmitter (this allows radio dialogue between
the barrier and the wireless ProxinetW2 control unit and with the Proxinet36, Proxinet76 and
Proxinet192 control units equipped with PXWRX receiver). Height 1 m with 4 detection beams
each consisting of two beams operating with AND logic (to stop the beam, it is necessary
to interrupt both the rays). It is also possible to set the AND function between two beams
in order to prevent false alarms. Optical synchronism between the two bars with simplified
alignment system. Range: 15 m indoors; 5 m outdoors. Minimum distance between the bars
40 cm. Alarm output with NC contact. Powered by 2 x 3.6 V 19 Ah lithium batteries (one per
bar), supplied as standard. Acoustic low battery alert. Battery duration of between 1 and 3
years. Operating temperature -10 to +65 °C. IP54 protection rating. Width 25 mm, depth
22 mm. Outer container dimensions 40 x 40 x 220 mm (-12 mm to obtain the total height).
Black.
Infrared barrier for doors and windows. Supplied with external containers for housing batteries
and the PXWCO perimeter detector to use as transmitter (this allows radio dialogue between
the barrier and the wireless ProxinetW2 control unit and with the Proxinet36, Proxinet76 and
Proxinet192 control units equipped with PXWRX receiver). Height 1,5 m with 6 detection
beams each consisting of two beams operating with AND logic (to stop the beam, it is
necessary to interrupt both the rays). It is also possible to set the AND function between
two beams in order to prevent false alarms. Optical synchronism between the two bars with
simplified alignment system. Range: 15 m indoors; 5 m outdoors. Minimum distance between
the bars 40 cm. Alarm output with NC contact. Powered by 2 x 3.6 V 19 Ah lithium batteries
(one per bar), supplied as standard. Acoustic low battery alert. Battery duration of between
1 and 3 years. Operating temperature -10 to +65 °C. IP54 protection rating. Width 25 mm,
depth 22 mm. Outer container dimensions 40 x 40 x 220 mm (-12 mm to obtain the total
height). Black.
Infrared barrier for doors and windows. Supplied with external containers for housing batteries
and the PXWCO perimeter detector to use as transmitter (this allows radio dialogue between
the barrier and the wireless ProxinetW2 control unit and with the Proxinet36, Proxinet76 and
Proxinet192 control units equipped with PXWRX receiver). Height 2 m with 8 detection beams
each consisting of two beams operating with AND logic (to stop the beam, it is necessary
to interrupt both the rays). It is also possible to set the AND function between two beams
in order to prevent false alarms. Optical synchronism between the two bars with simplified
alignment system. Range: 15 m indoors; 5 m outdoors. Minimum distance between the bars
40 cm. Output with NC alarm contact. Powered by 2 x 3.6 V 19 Ah lithium batteries (one
per bar), supplied as standard. Acoustic low battery alert. Battery duration of between 1 and
3 years. Operating temperature -10 to +65 °C. IP54 protection rating. Width 25 mm, depth
22 mm. Outer container dimensions 40 x 40 x 220 mm (-12 mm to obtain the total height).
Black.
Pack of 2 x 3.6 V 19 Ah batteries for BIWB205AS, BIWB410AS and BIWB615AS barriers.
BIWBOX
64360240
Pack of 2 spare outer containers for housing batteries and the PXWCO01 perimeter detector.
Housing the
PXWCOB01 - PXWCOM01
perimeter detector
BATTERIES
OUTER
CONTAINER
PXWCOB01
Perimeter detector
(not supplied as standard)
70
INFRARED BARRIERS FOR OUTDOOR USE
CODE
DESCRIPTION
BE260
64360130
Infrared barrier for outdoor use. Height 18.5 cm with 1 detection beam each consisting of
two beams operating with AND logic (to stop the beam, it is necessary to interrupt both the
rays). Optical synchronism between the two bars. Wall installation. Range: 250 m indoors;
60 m outdoors. Total current draw of columns 90 mA. Operating temperature -25 to +65 °C.
IP65 protection rating. Width 78 mm, depth 78 mm. Black.
BE260H
64360140
Internal heater kit for BE260 barriers. Consisting of a heating resistor and a special
thermostat, this guarantees a suitable temperature value inside the TX and RX devices,
allowing the smooth functioning of the barrier even at low temperatures. To be installed in
both the receiver and the transmitter (1 kit for each barrier). Total current draw of pair of
heaters 250 mA.
BQ10AS
64361601
BQ15AS
64361701
BE820AS
64360101
BE825AS
64360201
BISPL
64383200
Infrared barrier for outdoor use. Height 1 m with 16 cross detection rays. Possibility to set
the AND function, between two rays (the alarm is generated when two beams, from those
envisaged, are interrupted at the same time) or only between the first two rays, in order to
prevent false alarms. Optical synchronism between the two bars with simplified alignment
system. Can be wall-mounted or installed on a post. Range: 200 m indoors; 100 m
outdoors. Minimum distance between the bars 4 m. Power supply 10-30 V DC, current draw
135-210 mA per pair of columns (TX and RX). Built-in thermostatically-controlled heater,
separate 10-30 V AC-DC power supply, current draw 35-85 W per column. Operating
temperature -25 to +70 °C. IP65 protection rating. Width 60 mm, depth 60 mm. Black.
Infrared barrier for outdoor use. Height 1.5 m with 16 cross detection rays. Possibility to set
the AND function, between two rays (the alarm is generated when two beams, from those
envisaged, are interrupted at the same time) or only between the first two rays, in order to
prevent false alarms. Optical synchronism between the two bars with simplified alignment
system. Can be wall-mounted or installed on a post. Range: 200 m indoors; 100 m
outdoors. Minimum distance between the bars 4 m. Power supply 10-30 V DC, current draw
135-210 mA per pair of columns (TX and RX). Built-in thermostatically-controlled heater,
separate 10-30 V AC-DC power supply, current draw 35-85 W per column. Operating
temperature -25 to +70 °C. IP65 protection rating. Width 60 mm, depth 60 mm. Black.
Infrared barrier for outdoor use. Height 2 m with 36 cross detection rays. Possibility to set
the AND function, between two rays (the alarm is generated when two beams, from those
envisaged, are interrupted at the same time) or only between the first two rays, in order to
prevent false alarms. Optical synchronism between the two bars with simplified alignment
system. Can be wall-mounted or installed on a post. Range: 200 m indoors; 100 m
outdoors. Minimum distance between the bars 4 m. Power supply 10-30 V DC, current draw
135-210 mA per pair of columns (TX and RX). Built-in thermostatically-controlled heater,
separate 10-30 V AC-DC power supply, current draw 35-85 W per column. Operating
temperature -25 to +70 °C. IP65 protection rating. Width 60 mm, depth 60 mm. Black.
Infrared barrier for outdoor use. Height 2.5 m with 36 cross detection rays. Possibility to set
the AND function, between two rays (the alarm is generated when two beams, from those
envisaged, are interrupted at the same time) or only between the first two rays, in order to
prevent false alarms. Optical synchronism between the two bars with simplified alignment
system. Can be wall-mounted or installed on a post. Range: 200 m indoors; 100 m
outdoors. Minimum distance between the bars 4 m. Power supply 10-30 V DC, current draw
135-210 mA per pair of columns (TX and RX). Built-in thermostatically-controlled heater,
separate 10-30 V AC-DC power supply, current draw 35-85 W per column. Operating
temperature -25 to +70 °C. IP65 protection rating. Width 60 mm, depth 60 mm. Black.
Bracket for post/wall assembly for BQ810AS, BQ815AS, BE820AS, BE825AS barriers for
outdoor use (use 2 brackets for TX and 2 brackets for RX for each barrier).
BARRIERS
ITEM
71
DETECTORS FOR TECHNICAL ALARMS
LIQUID DETECTORS
ITEM
CODE
DESCRIPTION
RLI01
64400500
Liquid and moisture detector for floor installation. Plastic container. Output with NC contact
for connection to an alarm control unit. Power supply 12/24 V DC; current draw 30 mA.
Operating temperature -5 to +50 °C. Dimensions 80 x 80 x 20 mm.
RLI02
64400010
High-precision liquid detector for floor installation. Aluminium container. Output with NC
contact for connection to an alarm control unit. Power supply 12/24 V DC; current draw 40
mA. Operating temperature -10 to +50 °C. Dimensions: 120 x 37 x 26 mm.
ITEM
CODE
DESCRIPTION
PAR01
64400600
Vertical anti-theft button with memory and key reset. Plastic container. Operating
temperature -10 to +50 °C. Dimensions: 50 x 66 x 25 mm.
DETECTORS FOR TECHNICAL ALARMS
MANUAL ALARM ACTIVATORS
72
WIRED SIRENS
SIRENS FOR OUTDOOR USE
ITEM
CODE
DESCRIPTION
SA10L
64422300
Self-powered siren for outdoor use. White polycarbonate container. Sound power 101 dB
at 1 m. High-efficiency LED flasher. Possibility to select the acoustic signal from 8 different
versions. Current draw: at rest 18 mA, during alarm 1.2 A.
Operating temperature -25 to +55 °C. Protection rating IP34.
Dimensions 217 x 302 x 107 mm Takes 2 Ah battery (BB020).
SIRENS FOR INDOOR USE
ITEM
CODE
DESCRIPTION
BXSIAS01
64422000
Recessed siren for indoor use. ABS container. Sound power 80 dB at 1 m. Equipped with
reinforcements suitable for installation with plates used in the main wiring systems on a type
503 box. Current draw 30 mA. Operating temperature 5 to +40 °C. IP30 protection rating.
Dimensions 68 x 46 x 49 mm Black.
APF22
64422100
Wall-mounted siren for indoor use. ABS container. Sound power 114 dB at 1 m. Current
draw 200 mA. IP30 protection rating. Operating temperature -25 to +55 °C. Dimensions: 160
x 110 x 50 mm. White.
ITEM
CODE
DESCRIPTION
KITAS
64423000
Defoamer kit with steel case for SA10L sirens.
LASTR
64422600
Flashing light kit with xenon lamp for SA10L sirens.
WIRED SIRENS
ACCESSORIES FOR SIRENS
73
UNIVERSAL TELEPHONE DIALLERS
UNIVERSAL TELEPHONE DIALLERS
UNIVERSAL TELEPHONE DIALLERS
74
ITEM
CODE
DESCRIPTION
GSM11
64440060
GSM21
64440080
C4MO0401
64385800
Dual band GSM communicator (900/1800 MHz) with built-in keypad and display. 2 alarm
inputs, 20 storable phone numbers, 2 voice messages for signalling alarm events and a
message address for system identification. Possibility of sending text messages, voice
messages or both for each number stored. 4 open collector outputs that can be activated
remotely via SMS, DTMF tones or remote control function (output is activated with a simple
call to the communicator via a number stored in the phonebook. Remote activation function
free of charge) with notification that activation has taken place. Event memory (last 50
events). Programming using the keypad and display, text message or PRGSM programming
kit. No SIM provided. 12 V DC power supply. Takes 3 x AA 2.1 Ah - 1.2 V BB022 buffer
batteries. Current draw at rest 150 mA, during transmission 400 mA. Operating temperature
-5 to +40 °C. IP40 protection rating. Dimensions 260x130x42 mm.
Dual band GSM communicator (900/1800 MHz) with built-in keypad and display. 4 alarm
inputs, 20 storable phone numbers for alarm notifications. 4 voice messages for signalling
alarm events and a message address for system identification. Possibility of sending text
messages, voice messages or both for each number stored. 4 open collector outputs
that can be activated remotely via SMS, DTMF tones or in remote control mode (output is
activated with a simple call to the communicator via a number stored in the phonebook.
Remote activation function free of charge): Notification that activation of remote commands
has taken place. 50 additional storable phone numbers for controlling an output in remote
control mode (Barrier function). Burglar alarm control unit features (a code is used to enable
the operation of the inputs, totally or partially). Event memory (last 50 events). Programming
using the keypad and display, text message or PRGSM programming kit. No SIM provided.
12 V DC power supply. Takes 3 x AA 2.1 Ah - 1.2 V BB022 buffer batteries. Current draw
at rest 150 mA, during transmission 400 mA. Operating temperature -5 to +40 °C. IP40
protection rating. Dimensions 260x130x42 mm.
Card with 4 relays for connection to the open collector outputs on the GSM11 and GSM21
diallers.
BXANGM01
64441800
Additional external antenna for BXGM0001 and GSM21 telephone diallers, including 3 m
long cable.
BB022
64480020
AA 2.1 Ah - 1,2 V nickel-metal hydride battery for GSM11 - GSM21 series diallers. 3 are
required for each dialler.
PRGSM
64480040
Programming kit for GSM11 and GSM21 telephone diallers. RS232 interface for connection
to PC complete with GSManager programming software.
POWER SUPPLIES AND BATTERIES
UNIVERSAL POWER SUPPLIES
ITEM
CODE
DESCRIPTION
PXAL2
64440160
Auxiliary power supply for burglar alarm systems in metal container. Supply voltage 230 V
AC; output voltage 13.8 V DC. Output current 2 A; additional current for battery charging
0.5 A. Protection against short-circuits and overloads. Protection against excessive battery
discharge. Mains power failure relay output. Takes 1 x 7 Ah BB065 buffer battery. Operating
temperature -10 to +40 °C. IP20 protection rating. Dimensions 230 x 230 x 88 mm
PXAL3
64440170
Auxiliary power supply for burglar alarm systems in metal container. Supply voltage 230 V
AC; output voltage 13.8 V DC. Output current 3 A; additional current for battery charging
1 A. Protection against short-circuits and overloads. Protection against excessive battery
discharge. Open collector output for signalling mains power failure and device fault. Takes 1
x 17 Ah BB180 buffer battery. Operating temperature -10 to +40 °C. IP20 protection rating.
Dimensions 230 x 300 x 98 mm
ITEM
CODE
DESCRIPTION
PXALS15
64440180
PXALS30
64440190
Auxiliary power supply supervised for burglar alarm systems in metal container. Supply
voltage 230 V AC; output voltage 13.8 V DC. Output current 1.5 A. Protection against
short-circuits and overloads. When connected on the system bus, it communicates its
operating status to the control unit, analysing all operating conditions. The container takes 1
x 7Ah battery (BB065) and two of the following types of modules: PX8IR, PX8OR, PXABR.
Possibility of use even without the connection to the system bus as a standard power supply
station. 2 x OC outputs for local signalling of power supply fault and mains fault. Operating
temperature -10/+40°C. Dimensions: 405x295x90 mm. Regulatory compliance: EN 50131-6
Grade 2.
Auxiliary power supply supervised for burglar alarm systems in metal container. Supply
voltage 230 V AC; output voltage 13.8 V DC. Output current 3 A. Protection against
short-circuits and overloads. When connected on the system bus, it communicates its
operating status to the control unit, analysing all operating conditions. The container takes 1
x 17Ah battery (BB180) and five of the following types of modules: PX8IR, PX8OR, PXABR.
Possibility of use even without the connection to the system bus as a standard power supply
station. 2 x OC outputs for local signalling of power supply fault and mains fault. Operating
temperature -10/+40°C. Dimensions: 490x360x90 mm. Regulatory compliance: EN 50131-6
Grade 2.
ITEM
CODE
POWER SUPPLIES AND BATTERIES
POWER SUPPLIES SUPERVISED ON BUS
BATTERIES
DESCRIPTION
BB020
64480300
Lead-acid battery 12 V 2 Ah.
BB065
64480400
Lead-acid battery 12 V 7.2 Ah.
BB180
64480500
Lead-acid battery 12 V 17 Ah.
75
ACCESSORIES
PROGRAMMING CABLES
ITEM
CODE
DESCRIPTION
PXIPC
64380120
Programming cable kit. The package contains an RS232 cable, a RS232-USB converter and
a CD with PXManager software to use for programming Proxinet control units.
ITEM
CODE
DESCRIPTION
PXSTB
64380130
Temperature sensor. Can be used to control the control unit battery temperature. To be
connected to the control unit card. In the event of battery overheating, the charge voltage
supplied by the control unit is suitably adjusted.
TEMPERATURE SENSOR
BATTERY DISCHARGE PROTECTION CARD
ITEM
PXPSB
CODE
64380140
DESCRIPTION
Battery discharge protection card. Can be used to control the battery charge level of Proxinet
control units. When the charge level drops below a set threshold, the battery is disconnected
to prevent damage.
ANTENNA
ITEM
ACCESSORIES
PXANGM
CODE
64440150
DESCRIPTION
GSM antenna. Supplied with steel bracket and 10 m long cable. Can be used with PXGSM
module when the standard antenna is not receiving an adequate signal.
AMPLIFIER
ITEM
PXABR
CODE
64380150
DESCRIPTION
RS485 bus signal amplifier. This guarantees communication when the BUS line is very long
(over 400 m) or has numerous branches.
PROGRAMMING SOFTWARE
ITEM
PXMANAGER
CODE
N.A.
DESCRIPTION
Programming software. This allows the programming of all control unit parameters. The latest
version can be downloaded for free from the Bpt site.
BUS CABLE
ITEM
PXC75
CODE
64380170
DESCRIPTION
Bus cable for alarm systems, shielded and twisted grade 4. 2 x 0.75 + 2 x 2 x 0.22. 200 m
reel.
RELAY CARDS
ITEM
76
CODE
DESCRIPTION
RL002
64385500
Card with 2 relays for connection to the open collector outputs on the control unit.
RL004
64385600
Card with 4 relays for connection to the open collector outputs on the control unit.
RL008
64385700
Card with 8 relays for connection to the open collector outputs on the control unit.
KITS
Control units, detectors, sirens and batteries: all in one pack.
A practical solution to have everything you need to create an
efficient system to hand.
ITEM
CODE
DESCRIPTION
PXKIT01
64470070
PXKIT02
64470081
PXKIT03
64470091
PXKIT04
64470111
PXKITWL
64470141
Wired burglar alarm kit consisting of: 1 x PROXINET8 control unit, 1 x 12 V 7.2 Ah BB065
battery, 2 x PXIRV infrared volumetric detectors, 1 x SA10L self-powered sired for outdoor
use with flashing light, 1 x 12 V - 2 Ah BB020 battery, 1 x APF22 siren for indoor use.
Wired burglar alarm kit consisting of: 1 x PROXINET8 control unit, 1 x 12 V 7.2 Ah BB065
battery, 2 x PXDTV infrared volumetric detectors, 1 x SA10L self-powered sired for outdoor
use with flashing light, 1 x 12 V - 2 Ah BB020 battery, 1 x APF22 siren for indoor use.
Wired burglar alarm kit consisting of: 1 x PROXINET36 control unit, 1 x PXKTB keypad, 1 x
12 V 7.2 Ah BB065 battery, 2 x PXIRV infrared volumetric detectors, 1 x SA10L self-powered
sired for outdoor use with flashing light, 1 x 12 V - 2 Ah BB020 battery, 1 x APF22 siren for
indoor use.
Wired burglar alarm kit consisting of: 1 x PROXINET36 control unit, 1 x PXKTB keypad, 1 x
12 V 7.2 Ah BB065 battery, 2 x PXDTV dual technology detectors, 1 x SA10L self-powered
sired for outdoor use with flashing light, 1 x 12 V - 2 Ah BB020 battery, 1 x APF22 siren for
indoor use.
Wireless burglar alarm kit consisting of: 1 x PROXINETW 2 control unit, 1 x PXWCOB1
wireless perimeter detector, 1 x PXWIR01 volumetric detector, 1 x PXWRC remote control,
1 x BB020 12 V 2 Ah battery.
KITS
KITS
77
ANALYTICAL INDEX BY CODE
ANALYTICAL INDEX BY CODE
pg
22
26
30
34
38
59
40
40
40
40
59
59
40
41
41
63
63
64
64
63
63
63
53
53
53
64
62
62
62
68
63
68
68
68
66
66
56
58
56
56
63
56
64
64
54
54
63
63
63
63
64
64
68
68
63
64
63
63
64
63
64
63
63
68
68
68
68
69
78
CODE
64300070
64300081
64300091
64300111
64300121
64320021
64320030
64320040
64320050
64320060
64320070
64320080
64320090
64330020
64330380
64340120
64340130
64340140
64340150
64340160
64340170
64340180
64340191
64340211
64340221
64340250
64340260
64340270
64340280
64340290
64340300
64340310
64340320
64340330
64340340
64340350
64340360
64340370
64340380
64340390
64340400
64340410
64340420
64340430
64340440
64340450
64340500
64340600
64340700
64340800
64340900
64341000
64341900
64342200
64343600
64343700
64343800
64343900
64344000
64344100
64344300
64345500
64345600
64345700
64345900
64346000
64346200
64360010
ITEM
PROXINET8
PROXINET36
PROXINET76
PROXINET192
PROXINET W2
PXWRC
PXKIB
PXKIN
PXKTB
PXKTN
PXWKTB
PXWKTN
PXKD
PXTAG
PXITU
IPICB
IPICN
IPIVX
IPIVA
IPIXB
IPITM
IPITB
PXWIR01
PXWCOB01
PXWCOM01
PXDTCI
PXIRV
PXDTV
PXDTAM
CFSST02
IPIGB
SAC01
SAC02
CIS03
PXIRVE
PXDTVE
PXWDTCL
PXWDTVE
PXWIRCB
PXWDTCB
IPIGP
PXWDTCM
PXDTC01
PXDTCE
PXWIRFC
PXWIRWFC
IPILI
IPILV
IPIMA
IPITL
IPIVB
IPIVN
CFSST
RRV14
IPITT
IPIVP
IPIXA
IPIXN
IPILC
IPIGN
IPIVE
IPICT
IPIAB
CAS01
CFI02
RVB01
RIN01
BI205
pg
69
69
69
69
69
69
69
69
71
69
69
71
71
70
71
70
70
70
71
70
42
40
40
40
42
43
43
48
48
76
76
76
76
53
76
65
65
67
67
68
44
71
76
76
76
74
67
67
67
67
67
67
67
68
67
67
68
67
72
72
72
59
73
73
73
73
73
74
CODE
64360020
64360030
64360040
64360050
64360060
64360070
64360080
64360090
64360101
64360110
64360120
64360130
64360140
64360191
64360201
64360211
64360221
64360240
64361601
64361701
64360231
64380020
64380040
64380050
64380050
64380060
64380070
64380080
64380090
64380110
64380120
64380130
64380140
64380150
64380160
64380170
64380180
64380190
64380210
64380220
64380230
64380240
64383200
64385500
64385600
64385700
64385800
64386700
64386800
64386900
64387000
64387100
64387200
64387300
64387400
64387500
64387600
64387700
64387800
64400010
64400500
64400600
64420050
64422000
64422100
64422300
64422600
64423000
ITEM
BI410
BI615
BI820
BI825
BI205W
BI410W
BI615W
BI820W
BE820AS
BI825W
BI4SD
BE260
BE260H
BIWB205AS
BE825AS
BIWB410AS
BIWB615AS
BIWBOX
BQ10AS
BQ15AS
BIWB820AS
PXTEL
PX8IR
PX8OR
EBTAM
PXGSM
PXV64
PXV256
PXLAN
PXWEB
PXIPC
PXSTB
PXPSB
PXABR
PXWRX
PXC75
PXDTCS
PXDTCP
CSPM02
CSP60
CEG65
PXGPRS
BISPL
RL002
RL004
RL008
C4MO0401
CSP01
CSP02
CSP21
CIO21
CIO23
CIO22
CSA11
CSA12
CIP31
CXP31
CPA31
CSA31
RLI02
RLI01
PAR01
PXWSE
BXSIAS01
APF22
SA10L
LASTR
KITAS
pg
74
76
75
75
75
75
51
44
44
74
77
77
77
77
77
74
74
70
75
75
75
76
CODE
64440060
64440080
64440150
64440160
64440170
64440180
64440190
64440211
64440220
64440230
64441800
64470070
64470081
64470091
64470111
64470141
64480020
64480040
64480060
64480300
64480400
64480500
N. D.
ITEM
GSM11
GSM21
PXANGM
PXAL2
PXAL3
PXALS15
PXALS30
PXKNX
PXDGETH
PXDGWF
BXANGM01
PXKIT01
PXKIT02
PXKIT03
PXKIT04
PXKITWL
BB022
PRGSM
BBW219
BB020
BB065
BB180
PXMANAGER
ANALYTICAL INDEX BY ITEM
ITEM
APF22
BB020
BB022
BB065
BB180
BBW219
BE260
BE260H
BE820AS
BE825AS
BI205
BI205W
BI410
BI410W
BI4SD
BI615
BI615W
BI820
BI820W
BI825
BI825W
BISPL
BIWB205AS
BIWB410AS
BIWB615AS
BIWB820AS
BIWBOX
BQ10AS
BQ15AS
BXANGM01
BXSIAS01
C4MO0401
CAS01
CEG65
CFI02
CFSST
CFSST02
CIO21
CIO22
CIO23
CIP31
CIS03
CPA31
CSA11
CSA12
CSA31
CSP01
CSP02
CSP21
CSP60
CSPM02
CXP31
EBTAM
GSM11
GSM21
IPIAB
IPICB
IPICN
IPICT
IPIGB
IPIGN
IPIGP
IPILC
IPILI
IPILV
IPIMA
IPITB
IPITL
CODE
64422100
64480300
64480020
64480400
64480500
64480060
64360130
64360140
64360101
64360201
64360010
64360060
64360020
64360070
64360120
64360030
64360080
64360040
64360090
64360050
64360110
64383200
64360191
64360211
64360221
64360231
64360240
64361601
64361701
64441800
64422000
64385800
64345700
64380230
64345900
64341900
64340290
64387000
64387200
64387100
64387500
64340330
64387700
64387300
64387400
64387800
64386700
64386800
64386900
64380220
64380210
64387600
64380050
64440060
64440080
64345600
64340120
64340130
64345500
64340300
64344100
64340400
64344000
64340500
64340600
64340700
64340180
64340800
pg
63
63
64
64
64
64
64
64
63
63
63
73
73
72
74
38
34
26
30
22
40
40
76
75
75
75
75
76
76
44
44
62
64
64
64
65
65
62
66
44
42
76
62
66
41
40
40
40
77
77
77
77
77
51
40
40
48
76
76
76
41
42
43
43
53
53
56
56
ITEM
IPITM
IPITT
IPIVA
IPIVB
IPIVE
IPIVN
IPIVP
IPIVX
IPIXA
IPIXB
IPIXN
KITAS
LASTR
PAR01
PRGSM
PROXINET W2
PROXINET192
PROXINET36
PROXINET76
PROXINET8
PX8IR
PX8OR
PXABR
PXAL2
PXAL3
PXALS15
PXALS30
PXANGM
PXC75
PXDGETH
PXDGWF
PXDTAM
PXDTC01
PXDTCE
PXDTCI
PXDTCP
PXDTCS
PXDTV
PXDTVE
PXGPRS
PXGSM
PXIPC
PXIRV
PXIRVE
PXITU
PXKD
PXKIB
PXKIN
PXKIT01
PXKIT02
PXKIT03
PXKIT04
PXKITWL
PXKNX
PXKTB
PXKTN
PXLAN
PXMANAGER
PXPSB
PXSTB
PXTAG
PXTEL
PXV256
PXV64
PXWCOB01
PXWCOM01
PXWDTCB
PXWDTCL
CODE
64340170
64343600
64340150
64340900
64344300
64341000
64343700
64340140
64343800
64340160
64343900
64423000
64422600
64400600
64480040
64300121
64300111
64300081
64300091
64300070
64380040
64380050
64380150
64440160
64440170
64440180
64440190
64440150
64380170
64440220
64440230
64340280
64340420
64340430
64340250
64380190
64380180
64340270
64340350
64380240
64380060
64380120
64340260
64340340
64330380
64320090
64320030
64320040
64470070
64470081
64470091
64470111
64470141
64440211
64320050
64320060
64380090
N. D.
64380140
64380130
64330020
64380020
64380080
64380070
64340211
64340221
64340390
64340360
pg
56
58
48
53
56
54
54
59
59
59
53
59
68
76
76
76
72
72
68
68
73
68
68
ITEM
PXWDTCM
PXWDTVE
PXWEB
PXWIR01
PXWIRCB
PXWIRFC
PXWIRWFC
PXWKTB
PXWKTN
PXWRC
PXWRX
PXWSE
RIN01
RL002
RL004
RL008
RLI01
RLI02
RRV14
RVB01
SA10L
SAC01
SAC02
CODE
64340410
64340370
64380110
64340191
64340380
64340440
64340450
64320070
64320080
64320021
64380160
64420050
64346200
64385500
64385600
64385700
64400500
64400010
64342200
64346000
64422300
64340310
64340320
ANALYTICAL INDEX BY ITEM
pg
73
75
74
75
75
70
71
71
71
71
69
69
69
69
69
69
69
69
69
69
69
71
70
70
70
70
70
71
71
74
73
74
68
68
68
68
68
67
67
67
67
68
68
67
68
67
67
67
67
67
67
67
40
74
74
63
63
63
63
63
63
63
64
63
63
63
63
63
79
NOTES
80
81
Came Nord Est
Udine - ITALY
Came Nord Ovest
Cuneo - ITALY
Came Centro
Brescia - ITALY
Came Sud
Naples - ITALY
Came United Kingdom
Nottingham – UK
Came France
Paris – FRANCE
Came Spain
Madrid – SPAIN
Came Portugal
Lisbon – PORTUGAL
Came Deutschland GMBH
Stuttgart – GERMANY
Came Benelux
Lessines – BELGIUM
Came Nederland
Breda – NETHERLANDS
Came Poland
Warsaw – POLAND
Came Americas Automation
Miami – USA
Came Adriatic
Kastav – CROATIA
Came do Brasil Serviços de Automaçao
São Paulo - BRAZIL
Came Automatismos de Mexico
Mexico City - MEXICO
Came Rus
Moscow – RUSSIA
Came Gulf
Dubai - U.A.E.
Came India Automation Solutions
New Delhi – INDIA
Came S.p.A. has certified
Quality, Environment and Safety
management systems in
compliance with the following
standards:
UNI EN ISO 9001
UNI EN ISO 14001
BS OHSAS 18001
Came Bpt South Africa
Germiston – SOUTH AFRICA
Came S.p.A.
Via Martiri della Libertà, 15
31030 Dosson di Casier
Treviso – Italy
Tel. (+39) 0422 4940
Fax (+39) 0422 4941
[email protected] - www.came.com
© CAME SPA - KBCENAI016 - 03/2016 - EN/EN
EVEN PARTIAL REPRODUCTION IS FORBIDDEN
CAME RESERVES THE RIGHT TO MAKE MODIFICATIONS TO THIS DOCUMENT AT ANY TIME
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement