GLX handleidingen.indd

Add to my manuals
2 Pages

advertisement

GLX handleidingen.indd | Manualzz

RV-100 DIGITAL REVERB

RV-100 DIGITAL REVERB

OWNER’S MANUAL

INSTRUCTIONS

Thanks for purchasing our product. In order to make the best use of your

RV-100, please read the following carefully.

FEATURES

The RV-100 is a high quality, multifunction digital reverb effect. It features spring, plate, hall, room, gate and modulate reverb. Stereo output and studio quality sound ensure that the pedal can be used in any environment.

BATTERY REPLACEMENT

1. Loosen the screw on the pedal to open it.

2. Remove the battery from the battery compartment and disconnect the battery cable.

3. Connect a new battery to the battery cable and put it back in the battery compartment.

Make sure that the polarity of the battery is correct and the battery cable does not interfere with the spring or pedal cover.

4. Push the coil spring into the spring base and close the pedal.

5. Insert the thumb screw into the guide bush hole and firmly tighten the screw.

PANEL DESCRIPTION

1. AC Adaptor Jack: Connect an AC adaptor (100-140V/50-60Hz).

An AC adaptor allows long and secure operation without worrying about battery life.

Use the proper supply for your area’s Mains line voltage.

2. Indicator LED: This LED indicates when the effect is turned on.

• Operating on battery power only: when the LED becomes dim or does

not light the battery needs to be replaced.

3. Level Knob: Use this control to adjust the output level of the effect.

4. Tone Knob: Use this control to adjust the tone of the reverb. Rotate clockwise for a brighter sound and counter-clockwise for a warm sound.

5. Time Knob: Use this control to adjust the reverb time.

6. Mode Knob: Use this control to switch the reverb mode. Ordinary reverbs include spring, plate, hall, room and gate. Specialized reverbs include modulate.

7. Output Jacks A/B: Use the jacks to connect an amplifier or other units.

Use Jack A for mono output.

8. Pedal: Press the pedal to turn the effect on and off.

9. Thumb Screw: Loosen the screw to open the pedal for battery replacement. (For details of the battery replacement, see “BATTERY

REPLACEMENT”)

10. Input Jacks A/B: Connect your instrument to this jack. To prolong battery life, disconnect all cables from the pedal when it’s not in use.

IMPORTANT NOTES

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Do not use this apparatus near water.

5. Clean only with dry cloth.

6. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

7. Do not install near any heat sources such as radiators, heat registers, stoves or any other apparatus (including amplifiers) that create heat.

8. WARNING: to reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

9. Protect the power cord from being walked on or being pinched.

10. Unplug this apparatus when unused for long periods of time.

11. There are no user serviceable parts inside. All servicing has to be done by qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as when the power supply cord or plug is damaged, when liquid has been spilled or objects have fallen into the apparatus, when the apparatus has been exposed to rain or moisture, when the apparatus does not operate normally or when it has been dropped.

SPECIFICATIONS

Input Impedance 1MΩ

Output impedance 1kΩ

Recommended Load

Impedance

Residual Noise

Power Supply

Connections

Controls

Indicator

Current draw

Dimensions

Weight

Option

10kΩ or greater

-92dBu (IHF-A, Typ.)

DC 9V; Dry Battery (6F22/9V), AC adaptor

Input A (Mono) / B,

Output A (Mono) / B,

AC Adaptor

Pedal Switch, Level, Tone,

Time, Mode

Check indicator (serves also as battery check indicator)

55mA, (DC 9V)

72*128*60 mm.

415g (no battery)

AC adaptor

CONNECTIONS

1. Connecting an instrument to this jack will automatically switch the unit on.

Be sure to disconnect the cord from this jack when the unit is not being used.

2. Before connecting or disconnecting any instrument, make sure that the volume of the amplifier is turned down.

3. For monaural output, use Output Jack A. Both the dry and the processed signal are output.

4. For stereo use:

Output A: only the processed signal is output.

Output B: only the dry

(unprocessed) signal is output.

5. When you use a high output guitar, the sound may be distorted. If distortion occurs, turn down the volume of the guitar or use a limiter.

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement