D-Link | KX-TDA100 | User's Manual | D-Link KX-TDA100 User's Manual

Hybrid IP-PBX
Installation Manual
Model
KX-TDA100
KX-TDA200
Thank you for purchasing a Panasonic Hybrid IP-PBX.
Please read this manual carefully before using this product and save this manual for future use.
KX-TDA100/KX-TDA200: Version 2.0
SD Logo is
a trademark.
System Components
System Components Table
Model
Shelves
KX-TDA100
Basic Shelf
KX-TDA200
Basic Shelf
Main Processing Card
MPR Option Card
Trunk Cards
Extension Cards
2
Installation Manual
Description
Main Processing Card (MPR)
KX-TDA0105
Memory Expansion Card (MEC)
KX-TDA0196
Remote Card (RMT)
KX-TDA0180
8-Port Analogue Trunk Card (LCOT8)
KX-TDA0181
16-Port Analogue Trunk Card (LCOT16)
KX-TDA0182
8-Port DID Card (DID8)
KX-TDA0183
4-Port Analogue Trunk Card (LCOT4)
KX-TDA0184
8-Port E & M Trunk Card (E&M8)
KX-TDA0187
T-1 Trunk Card (T1)
KX-TDA0188
E-1 Trunk Card (E1)
KX-TDA0189
8-Port Caller ID/Pay Tone Card (CID/PAY8)
KX-TDA0193
8-Port Caller ID Card (CID8)
KX-TDA0284
4-Port BRI Card (BRI4)
KX-TDA0288
8-Port BRI Card (BRI8)
KX-TDA0290CE/CJ
PRI Card (PRI30)
KX-TDA0290
PRI Card (PRI23)
KX-TDA0480
4-Channel VoIP Gateway Card (IP-GW4)
KX-TDA0484
4-Channel VoIP Gateway Card (IP-GW4E)
KX-TDA0490
16-Channel VoIP Gateway Card (IP-GW16)
KX-TDA0143
4 Cell Station Interface Card (CSIF4)
KX-TDA0144
8 Cell Station Interface Card (CSIF8)
KX-TDA0170
8-Port Digital Hybrid Extension Card (DHLC8)
KX-TDA0171
8-Port Digital Extension Card (DLC8)
KX-TDA0172
16-Port Digital Extension Card (DLC16)
KX-TDA0173
8-Port Single Line Telephone Extension Card (SLC8)
KX-TDA0174
16-Port Single Line Telephone Extension Card (SLC16)
KX-TDA0175
16-Port Single Line Telephone Extension with Message
Lamp Card (MSLC16)
KX-TDA0470
16-Channel VoIP Extension Card (IP-EXT16)
System Components Table
Model
Other Cards
Description
KX-TDA0161
4-Port Doorphone Card (DPH4)
KX-TDA0162
2-Port Doorphone Card (German Type) (DPH2)
KX-TDA0164
4-Port External Input/Output Card (EIO4)
KX-TDA0166
16-Channel Echo Canceller Card (ECHO16)
KX-TDA0168
Extension Caller ID Card (EXT-CID)
KX-TDA0190
Optional 3-Slot Base Card (OPB3)
KX-TDA0191
4-Channel Message Card (MSG4)
KX-TDA0410
CTI Link Card (CTI-LINK)
Optional SD Memory
Cards
KX-TDA0820
SD Memory Card for Software Upgrade
KX-TDA0920
SD Memory Card for Software Upgrade to Enhanced
Version
Power Supply Units
(PSUs)
KX-TDA0103
L-Type Power Supply Unit (PSU-L)
KX-TDA0104
M-Type Power Supply Unit (PSU-M)
KX-TDA0108
S-Type Power Supply Unit (PSU-S)
KX-TDA0141CE
2-Channel Cell Station Unit Using a DHLC/DLC Card (PTinterface CS) for DECT Portable Station
KX-TDA0141
2-Channel Cell Station Unit Using a DHLC/DLC Card (PTinterface CS) for 2.4 GHz Portable Station
KX-TDA0142CE
4-Channel Cell Station Unit Using a CSIF Card for DECT
Portable Station
KX-TDA0142
3-Channel Cell Station Unit Using a CSIF Card for 2.4 GHz
Portable Station
KX-A228
S/M-type Back-up Battery Cable
KX-A229
L-type Back-up Battery Cable
KX-A258
Blank Slot Cover
KX-T30865
Doorphone
Cell Stations (CSs)
Proprietary Equipment
Installation Manual
3
Available Proprietary Telephones
The Hybrid IP-PBX supports all of the Panasonic KX-T7000, KX-TD7000, KX-TCA, and KX-NT series:
•
Digital/Analogue/IP proprietary telephones (e.g., KX-T7625, KX-T7630, KX-T7633, KX-T7636,
KX-NT136)
•
Portable stations (e.g., KX-TD7590, KX-TD7690, KX-TCA155, KX-TCA255)
•
DSS consoles (e.g., KX-T7640)
•
Single line telephones (e.g., KX-T7710)
Note
The Hybrid IP-PBX does not support the following telephones:
•
KX-T30800 series Proprietary Telephones and DSS consoles
•
KX-T61600 series Proprietary Telephones and DSS consoles
•
KX-T123200 series Proprietary Telephones and DSS consoles
•
KX-TD7500 DECT Portable Station
For the equipment (e.g., Add-on Key Module, USB Module, Headset*1) that can be connected to a particular
telephone, refer to the telephone's manual.
For other equipment that can be connected to the Hybrid IP-PBX, refer to "1.2.2 System Connection
Diagram".
Abbreviations in this manual
Proprietary telephone: PT
Digital proprietary telephone: DPT
Analogue proprietary telephone: APT
IP proprietary telephone: IP-PT
Portable station: PS
Single line telephone: SLT
Notice
•
There are some optional service cards and features that are not available for certain countries/
areas. Consult your certified Panasonic dealer for detailed instructions.
•
The power supply capacity of the Hybrid IP-PBX may differ from the values described in this
manual depending on the model number. Please consult your dealer for detailed information.
•
The KX-TDA100CN and KX-TDA200CN have a power supply unit (PSU-S and PSU-M,
respectively) pre-installed.
*1
4
The KX-T7090 headset can be connected to the KX-T7000, KX-T7200, KX-T7300, KX-T7400, and KX-T7500 (except for KX-T7560/KXT7565) series telephones.
Installation Manual
Important Safety Instructions
SAFETY REQUIREMENTS
When using your telephone equipment, basic safety precautions should always be followed to reduce the
risk of fire, electric shock and injury to persons, including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning.
4. Do not use this product near water, for example, near a bathtub, wash bowl, kitchen sink, or laundry
tub, in a wet basement, or near a swimming pool.
5. Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious
damage to the product.
6. Slots and openings in the cabinet and the back or bottom are provided for ventilation; to protect it from
overheating, these openings must not be blocked or covered. The openings should never be blocked
by placing the product on a bed, sofa, rug, or other similar surface. This product should never be placed
near or over a radiator or other heat source. This product should not be placed in a built-in installation
unless proper ventilation is provided.
7. This product should be operated only from the type of power source indicated on the product label. If
you are not sure of the type of power supply to your home, consult your dealer or local power company.
8. This product is equipped with a 3-wire earthing type plug, a plug having a third (earthing) pin. This plug
will only fit into an earthing type power outlet. This is a safety feature. If you are unable to insert the plug
into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose
of the earthing type plug.
9. Do not allow anything to rest on the power cord. Do not locate this product where the cord will be
abused by people walking on it.
10. Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock.
11. Never push objects of any kind into this product through cabinet slots as they may touch dangerous
voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of
any kind on the product.
12. To reduce the risk of electric shock, do not disassemble this product, but take it to a qualified person
when some service or repair work is required. Opening or removing covers may expose you to
dangerous voltages or other risks. Incorrect reassembly can cause electric shock when the appliance
is subsequently used.
13. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the
following conditions:
a)
b)
c)
d)
When the power supply cord or plug is damaged or frayed.
If liquid has been spilled into the product.
If the product has been exposed to rain or water.
If the product does not operate normally by following the operating instructions. Adjust only those
controls that are covered by the operating instructions because improper adjustment of other
controls may result in damage and will often require extensive work by a qualified technician to
restore the product to normal operation.
e) If the product has been dropped or the cabinet has been damaged.
f) If the product exhibits a distinct change in performance.
14. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote
risk of electric shock from lightning.
Installation Manual
5
15. Do not use the telephone to report a gas leak in the vicinity of the leak.
SAVE THESE INSTRUCTIONS
6
Installation Manual
Precaution
•
•
•
•
•
Keep the unit away from heating appliances and electrical noise generating devices such as fluorescent
lamps, motors and televisions. These noise sources can interfere with the performance of the Hybrid
IP-PBX.
This unit should be kept free of dust, moisture, high temperature (more than 40 °C) and vibration, and
should not be exposed to direct sunlight.
Never attempt to insert wires, pins, etc. into the vents or other holes of this unit.
If there is any trouble, disconnect the unit from the telephone line. Plug an SLT into the telephone line.
If the telephone operates properly, do not reconnect the unit to the line until the trouble has been
repaired by an authorised Panasonic Factory Service Centre. If the telephone does not operate
properly, chances are that the trouble is in the telephone network, and not in the Hybrid IP-PBX.
Do not use benzene, thinner, or the like, or any abrasive powder to clean the cabinet. Wipe it with a soft
cloth.
For users in Germany only
•
When the unit is working, the noise is less than 70 dB (A) according to DIN 45635 Part 19.
For users in Finland, Norway and Sweden only (KX-TDA100/KX-TDA200 only)
•
This unit may only be installed in a room or space with restricted access, and equipotential bonding
must be applied. For information on earthing, refer to "2.2.5 Frame Earth Connection".
For users in New Zealand only
•
This equipment shall not be set to make automatic calls to the Telecom '111' Emergency Service.
•
The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted
that the item complies with minimum conditions for connection to its network. It indicates no
endorsement of the product by Telecom, nor does it provide any sort of warranty. Above all, it provides
no assurance that any item will work correctly in all respects with another item of Telepermitted
equipment of a different make or model, nor does it imply that any product is compatible with all of
Telecom's network services.
•
This equipment is not capable, under all operating conditions, of correct operation at the higher speeds
for which it is designed. Telecom will accept no responsibility should difficulties arise in such
circumstances.
•
Some parameters required for compliance with Telecom's Telepermit requirements are dependent on
the equipment (PBX) associated with this modem. In order to operate within the limits for compliance
with Telecom's Specifications, the associated PBX equipment shall be sent to ensure that modem calls
are answered between 3 and 30 seconds of receipt of ringing.
•
IMPORTANT NOTICE
Under power failure conditions, the wireless telephones may not operate. Please ensure that a separate
telephone, not dependent on local power, is available for emergency use in emergencies.
For users in Australia only
•
No External TRC Terminal is provided due to an Internal Link between PE and TRC.
WARNING
•
THIS UNIT MAY ONLY BE INSTALLED AND SERVICED BY QUALIFIED SERVICE
PERSONNEL.
Installation Manual
7
•
•
•
•
•
WHEN A FAILURE OCCURS WHICH EXPOSES ANY INTERNAL PARTS,
DISCONNECT THE POWER SUPPLY CORD IMMEDIATELY AND RETURN THIS UNIT
TO YOUR DEALER.
DISCONNECT THE TELECOM CONNECTION BEFORE DISCONNECTING THE
POWER CONNECTION PRIOR TO RELOCATING THE EQUIPMENT, AND
RECONNECT THE POWER FIRST.
THIS UNIT IS EQUIPPED WITH AN EARTHING CONTACT PLUG. FOR SAFETY
REASONS THIS PLUG MUST ONLY BE CONNECTED TO AN EARTHING CONTACT
SOCKET WHICH HAS BEEN INSTALLED ACCORDING TO REGULATIONS.
TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR MOISTURE.
THE POWER SUPPLY CORD IS USED AS THE MAIN DISCONNECT DEVICE.
ENSURE THAT THE SOCKET-OUTLET IS LOCATED/INSTALLED NEAR THE
EQUIPMENT AND IS EASILY ACCESSIBLE.
CAUTION
DANGER OF EXPLOSION EXISTS IF THE BATTERY IS INCORRECTLY REPLACED. REPLACE THE
BATTERY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE BATTERY
MANUFACTURER. DISPOSE OF USED BATTERIES ACCORDING TO THE MANUFACTURER'S
INSTRUCTIONS.
The serial number of this product may be found on the label affixed to the
side of the unit. You should note the model number and the serial number
of this unit in the space provided and retain this book as a permanent
record of your purchase to aid in identification in the event of theft.
MODEL No.:
SERIAL No.:
For your future reference
DATE OF PURCHASE
NAME OF DEALER
DEALER'S ADDRESS
DEALER'S TEL. NO.
8
Installation Manual
The KX-TDA100E/KX-TDA200E, the KX-TDA100NE/KX-TDA200NE, the KXTDA100GR/KX-TDA200GR, and the KX-TDA100CE/KX-TDA200CE are designed to
interwork with the:
• Analogue Public Switched Telephone Network (PSTN) of European countries
• Pan-European Integrated Services Digital Network (ISDN) using ISDN basic rate access
• Pan-European Integrated Services Digital Network (ISDN) using ISDN primary rate
access
• ONP 2048 kbit/s digital structured leased lines (D2048S)
We, Panasonic Communications Co., Ltd./Panasonic Communications Company (U.K.) Ltd., declare
that this equipment is in compliance with the essential requirements and other relevant provisions of
Directive 1999/5/EC.
If you would like to receive a copy of the original Declaration of Conformity of our products which
relates to the R&TTE, please visit our web address:
http://doc.panasonic.de
Installation Manual
9
Introduction
This Installation Manual is designed to serve as an overall technical reference for the Panasonic Hybrid IPPBX, KX-TDA100/KX-TDA200. It provides instructions for installing the hardware, and programming the
Hybrid IP-PBX using the KX-TDA Maintenance Console.
The Structure of this Manual
This manual contains the following sections:
Section 1 System Outline
Provides general information on the Hybrid IP-PBX, including the system capacity and specifications.
Section 2 Installation
Describes the procedures to install the Hybrid IP-PBX. Detailed instructions for planning the installation
site, installing the shelves and optional service cards, and cabling of peripheral equipment are provided.
Further information on system expansion and peripheral equipment installation is included.
Section 3 Guide for the KX-TDA Maintenance Console
Explains the installation procedure, structure, and basic information of the KX-TDA Maintenance
Console.
Section 4 Troubleshooting
Provides information on the Hybrid IP-PBX and telephone troubleshooting.
About the Other Manuals
Along with this Installation Manual, the following manuals are available:
Feature Guide
Describes all basic, optional and programmable features of the Hybrid IP-PBX, and step-by-step
instruction for performing system programming using a proprietary telephone or a personal computer
(PC).
User Manual
Provides operating instructions for end users using a PT, SLT, PS, or DSS Console.
Trademarks
•
•
•
•
10
Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in
the United States and/or other countries.
Intel and Pentium are trademarks or registered trademarks of Intel Corporation or its subsidiaries
in the United States and other countries.
All other trademarks identified herein are the property of their respective owners.
Screen shots reprinted with permission from Microsoft Corporation.
Installation Manual
Precautions for Users in the United Kingdom
FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT CAREFULLY.
This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 5 amp
fuse is fitted in this plug. Should the fuse need to be replaced, please ensure that the replacement fuse has
a rating of 5 amps and that it is approved by ASTA or BSI to BS1362.
Check for the ASTA mark
or the BSI mark
on the body of the fuse.
If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If
you lose the fuse cover, the plug must not be used until a replacement cover is obtained. A replacement
fuse cover can be purchased from your local Panasonic Dealer.
IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR PREMISES,
THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY.
THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO
ANY 13 AMP SOCKET.
If a new plug is to be fitted, please observe the wiring code as shown below. If in any doubt, please consult
a qualified electrician.
WARNING
THIS APPLIANCE MUST BE EARTHED.
IMPORTANT: The wires in this mains leads are coloured in accordance with the following code:
Green-and-yellow: Earth
Blue: Neutral
Brown: Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured
markings identifying the terminals in your plug, proceed as follows.
The wire that is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug that is
marked with the letter E or by the safety earth symbol
or coloured GREEN or GREEN-AND-YELLOW.
The wire that is coloured BLUE must be connected to the terminal that is marked with the letter N or
coloured BLACK.
The wire that is coloured BROWN must be connected to the terminal that is marked with the letter L or
coloured RED.
Installation Manual
11
How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse and fuse
cover.
The equipment must be connected to direct exchange lines and a payphone should not be connected as an
extension.
999 and 112 can be dialled on the apparatus after accessing the Exchange line for the purpose of making
outgoing calls to the BT emergency (999) and (112) service.
During dialling, this apparatus may tinkle the bells of other telephones using the same line. This is not a fault
and we advise you not to call the Fault Repair Service.
12
Installation Manual
Table of Contents
1
System Outline......................................................................................17
1.1
1.1.1
1.2
1.2.1
1.2.2
1.3
1.3.1
1.4
1.4.1
1.4.2
1.4.3
2
System Highlights .......................................................................................................... 18
System Highlights............................................................................................................. 18
Basic System Construction........................................................................................... 20
Basic Shelf ....................................................................................................................... 20
System Connection Diagram............................................................................................ 21
Options ............................................................................................................................ 24
Options ............................................................................................................................. 24
Specifications ................................................................................................................. 27
General Description.......................................................................................................... 27
Characteristics.................................................................................................................. 29
System Capacity .............................................................................................................. 30
Installation .............................................................................................37
2.1
2.1.1
2.2
2.2.1
2.2.2
2.2.3
2.2.4
2.2.5
2.2.6
2.2.7
2.2.8
2.2.9
2.2.10
2.2.11
2.2.12
2.2.13
2.2.14
2.3
2.3.1
2.3.2
2.3.3
2.4
2.4.1
2.4.2
2.4.3
2.4.4
2.4.5
2.4.6
2.4.7
2.4.8
2.4.9
2.4.10
2.4.11
Before Installation .......................................................................................................... 38
Before Installation............................................................................................................. 38
Installation of the Hybrid IP-PBX .................................................................................. 40
Unpacking......................................................................................................................... 40
Names and Locations....................................................................................................... 41
Opening/Closing the Front Cover ..................................................................................... 42
Installing/Replacing the Power Supply Unit ...................................................................... 44
Frame Earth Connection .................................................................................................. 48
Backup Batteries Connection ........................................................................................... 49
Installing/Removing the Optional Service Cards .............................................................. 50
Types of Connectors......................................................................................................... 55
Attaching a Ferrite Core ................................................................................................... 57
Fastening Amphenol Type Connector .............................................................................. 59
Wall Mounting (KX-TDA200) ............................................................................................ 61
Wall Mounting (KX-TDA100) ............................................................................................ 63
Floor Standing (KX-TDA200 Only) ................................................................................... 65
Surge Protector Installation .............................................................................................. 68
Installation of the Main Processing Card ..................................................................... 71
MPR Card......................................................................................................................... 71
MEC Card......................................................................................................................... 73
RMT Card......................................................................................................................... 74
Installation of the Trunk Cards...................................................................................... 75
LCOT4, LCOT8, and LCOT16 Cards................................................................................ 75
DID8 Card ........................................................................................................................ 77
CID/PAY8 Card ................................................................................................................. 79
CID8 Card ........................................................................................................................ 80
E&M8 Card....................................................................................................................... 81
T1 Card ............................................................................................................................ 84
E1 Card ............................................................................................................................ 87
BRI4 and BRI8 Cards ....................................................................................................... 90
PRI30 Card....................................................................................................................... 94
PRI23 Card....................................................................................................................... 98
IP-GW4 Card .................................................................................................................. 101
Installation Manual
13
2.4.12
2.4.13
2.5
2.5.1
2.5.2
2.5.3
2.5.4
2.5.5
2.5.6
2.5.7
2.5.8
2.6
2.6.1
2.6.2
2.6.3
2.6.4
2.6.5
2.6.6
2.6.7
2.7
2.7.1
2.7.2
2.7.3
2.7.4
2.8
2.8.1
2.8.2
2.8.3
2.8.4
2.8.5
2.8.6
2.8.7
2.8.8
2.9
2.9.1
2.9.2
2.9.3
2.9.4
2.9.5
2.9.6
2.9.7
2.9.8
2.10
2.10.1
2.11
2.11.1
2.12
2.12.1
2.13
2.13.1
14
IP-GW4E Card ................................................................................................................103
IP-GW16 Card................................................................................................................. 105
Installation of the Extension Cards .............................................................................107
CSIF4 and CSIF8 Card ...................................................................................................107
DHLC8 Card....................................................................................................................109
DLC8 Card ......................................................................................................................112
DLC16 Card ....................................................................................................................114
SLC8 Card ......................................................................................................................116
EXT-CID Card ................................................................................................................. 118
SLC16 and MSLC16 Cards............................................................................................. 119
IP-EXT16 Card................................................................................................................121
Installation of the Other Cards.....................................................................................123
OPB3 Card......................................................................................................................123
DPH4 Card......................................................................................................................124
DPH2 Card......................................................................................................................126
EIO4 Card .......................................................................................................................129
ECHO16 Card ................................................................................................................. 132
MSG4 Card .....................................................................................................................133
CTI-LINK Card ................................................................................................................134
Connection of Extensions............................................................................................136
Maximum Cabling Distances of the Extension Wiring (Twisted Cable) ...........................136
Parallel Connection of the Extensions ............................................................................137
Digital EXtra Device Port (Digital XDP) Connection........................................................139
First Party Call Control CTI Connection ..........................................................................144
Connection of DECT Portable Stations....................................................................... 145
Overview .........................................................................................................................145
Procedure Overview........................................................................................................ 147
Site Planning ................................................................................................................... 149
Before Site Survey ..........................................................................................................153
Site Survey Using the KX-TCA255/KX-TD7590.............................................................. 157
After Site Survey .............................................................................................................161
Connecting a Cell Station to the Hybrid IP-PBX .............................................................162
Wall Mounting ................................................................................................................. 171
Connection of 2.4 GHz Portable Stations ...................................................................173
Overview .........................................................................................................................173
Procedure Overview........................................................................................................ 175
Site Planning ................................................................................................................... 177
Before Site Survey ..........................................................................................................181
Site Survey......................................................................................................................183
After Site Survey .............................................................................................................187
Connecting a Cell Station to the Hybrid IP-PBX .............................................................188
Wall Mounting ................................................................................................................. 196
Connection of Doorphones, Door Openers, External Sensors, and External Relays....198
Connection of Doorphones, Door Openers, External Sensors, and External Relays .....198
Connection of Peripherals ........................................................................................... 201
Connection of Peripherals ...............................................................................................201
Power Failure Connections ..........................................................................................205
Power Failure Connections ............................................................................................. 205
Starting the Hybrid IP-PBX........................................................................................... 209
Starting the Hybrid IP-PBX ............................................................................................. 209
Installation Manual
3
Guide for the KX-TDA Maintenance Console ...................................213
3.1
3.1.1
3.2
3.2.1
3.3
3.3.1
4
Troubleshooting ..................................................................................221
4.1
4.1.1
4.1.2
4.1.3
4.1.4
4.1.5
5
Overview ....................................................................................................................... 214
Overview......................................................................................................................... 214
Connection.................................................................................................................... 215
Connection ..................................................................................................................... 215
Installation of the KX-TDA Maintenance Console ..................................................... 217
Installing and Starting the KX-TDA Maintenance Console ............................................. 217
Troubleshooting ........................................................................................................... 222
Installation ...................................................................................................................... 222
Connection ..................................................................................................................... 224
Operation........................................................................................................................ 226
Using the Reset Button .................................................................................................. 228
Troubleshooting by Error Log ......................................................................................... 229
Appendix..............................................................................................241
5.1
5.1.1
5.1.2
Revision History ........................................................................................................... 242
Version 1.1...................................................................................................................... 242
Version 2.0...................................................................................................................... 243
Index ..........................................................................................................245
Installation Manual
15
16
Installation Manual
Section 1
System Outline
This section provides general information on the Hybrid IPPBX, including the system capacity and specifications.
Installation Manual
17
1.1 System Highlights
1.1
System Highlights
1.1.1
System Highlights
Networking Features
This Hybrid IP-PBX supports the following networking features:
TIE Line Service
A TIE line is a privately leased communication line between 2 or more PBXs, which provides cost
effective communications between company members at different locations.
Virtual Private Network (VPN)
VPN is a service provided by the telephone company. It uses an existing line as if it were a private line.
QSIG Network
QSIG is a protocol which is based on ISDN (Q.931) and offers enhanced PBX features in a private
network.
Voice over Internet Protocol (VoIP) Network
The PBX can connect to another PBX via a private IP network. In this case, voice signals are converted
into IP packets and sent through this network.
Built-in Small Call Centre Features
An incoming call distribution group can be used as a small call centre with the following features:
Queuing Feature
When a preprogrammed number of extensions in an incoming call distribution group are busy,
additional incoming calls can wait in a queue. While calls are waiting in the queue, the calls are handled
by the Queuing Time Table, which can be assigned for each time mode (day/lunch/break/night).
Log-in/Log-out
Incoming call distribution group members can join (Log-in) or leave (Log-out) the groups manually.
While logged-in, a member extension can have a preprogrammed time period automatically for refusing
calls after completing the last call (Wrap-up).
VIP Call
It is possible to assign a priority to incoming call distribution groups. If an extension belongs to multiple
groups and the extension becomes idle, queuing calls in the groups will be distributed to the extension
in priority order.
Computer Telephony Integration (CTI) Features
Connecting a personal computer (PC) to a DPT, or connecting a Server PC to this Hybrid IP-PBX allows
function of the PC, PBX and extension to be integrated so that, for example, detailed caller information can
be taken from a database and displayed on the PC as a call arrives, or the PC can dial numbers for the
extension automatically.
Voice Mail Features
This Hybrid IP-PBX supports Voice Processing Systems (VPS) with DTMF Integration as well as DPT
(Digital) Integration.
18
Installation Manual
1.1 System Highlights
Parallelled Telephone Features
By connecting telephones in parallel, you can increase the number of telephones connected to the PBX
without adding additional extension cards.
Parallel Mode
An SLT can be connected to an APT or DPT which is connected to a Super Hybrid Port of the PBX. The
SLT shares the same extension number with the APT or DPT.
EXtra Device Port (XDP) Mode
An SLT can be connected to a DPT which is connected to a Super Hybrid Port of the PBX. Unlike
parallel mode, XDP mode allows each telephone to act as an independent extension with its own
extension number.
Digital XDP
A DPT can be connected to another DPT which is connected to a DPT port or a Super Hybrid Port of
the PBX. Similar to XDP mode, each DPT acts as an independent extension with its own extension
number.
Portable Station (PS) Features
PSs (e.g., KX-TD7690) can be connected to this Hybrid IP-PBX. It is possible to use the Hybrid IP-PBX
features using the PS like a PT. A PS can also be used in parallel with a wired telephone (Wireless XDP
Parallel Mode). In this case, the wired telephone is the main telephone and the PS is the sub telephone.
PC Phone/PC Console Features
This Hybrid IP-PBX supports PC Phone and PC Console. These Panasonic CTI applications provide
advanced features combining telephone and PC, such as the ability to display detailed caller information,
including a photograph, on the screen of the PC when a call is received, or to dial a telephone number
automatically just by selecting a name.
Hospitality Features
This Hybrid IP-PBX has several features that support its use in a hotel-type environment. Extensions
corresponding to guest rooms can be "checked in" or "checked out" by a designated hotel operator, who can
also check or set wake-up calls, and print out records of guest charges.
Installation Manual
19
1.2 Basic System Construction
1.2
Basic System Construction
1.2.1
Basic Shelf
The basic shelf contains an MPR card. For system expansion, optional service cards and a power supply
unit can be installed in the basic shelf.
KX-TDA100
KX-TDA200
Construction of Basic Shelf
A: Slots for Expansion
B: MPR Card
A
A
B
20
Installation Manual
B
1.2 Basic System Construction
1.2.2
System Connection Diagram
Private
IP Network
Trunk (Telephone Company Lines)
Analogue/BRI/PRI/T1/E1
Remote PC
Router
Hybrid IP-PBX
PC
Batteries
IP-PT
SLT
PC
Server PC
SLT
PC
PC
Printer
Fax Machine
DPT
PC
External Sensor/
External Relay Device
Wireless Phone
APT
DSS Console
DPT
DSS Console
ISDN Telephone
Doorphone & Door Opener
BGM/Music On Hold (MOH)
PS
CS
USB
Pager/ Amplifier
Speaker
KX-T7636/
KX-T7633
PC
Voice Processing
System
KX-T7600 DPT
KX-T7600 DPT
Installation Manual
21
1.2 Basic System Construction
Hybrid IP-PBX
LCOT4
(KX-TDA0183)
LCOT16
LCOT16
(KX-TDA0181)
(KX-TDA0181)
LCOT8
LCOT8
(KX-TDA0180)
(KX-TDA0180)
CID/PAY8
(KX-TDA0189)
Analogue
Trunk
Telephone
Company
E & M Line
ISDN BRI Line
(Digital Trunk)
ISDN PRI Line
(Digital Trunk)
CID8
(KX-TDA0193)
DID8
(KX-TDA0182)
DLC16
(KX-TDA0172)
KX-T7636/
KX-T7633
DHLC8
(KX-TDA0170)
DPT
DSS Console
APT
DPT
E1 Line
(Digital Trunk)
SLC16
(KX-TDA0174)
BRI4
(KX-TDA0284)
SLC8
(KX-TDA0173)
BRI8
(KX-TDA0288)
EXT-CID
(KX-TDA0168)
PRI23
(KX-TDA0290)
T1
(KX-TDA0187)
E1
(KX-TDA0188)
PT-interface CS
DSS Console
Voice
Processing
System
PS
Fax Machine
KX-T7636/
KX-T7633
SLT Wireless Phone PT-interface CS PS
Voice
Processing
System
Wireless Phone
Router
IP-EXT16
(KX-TDA0470)
LAN
CSIF4
(KX-TDA0143)
CSIF8
(KX-TDA0144)
CS
IP-PT
PS
CTI-LINK
(KX-TDA0410)
IP-GW4
(KX-TDA0480)
OPB3
(KX-TDA0190)
IP-GW4E
(KX-TDA0484)
DPH4
(KX-TDA0161)
IP-GW16
(KX-TDA0490)
DPH2
(KX-TDA0162)
PC
Server PC*2
Doorphone & Door Opener
EIO4
(KX-TDA0164)
ECHO16
(KX-TDA0166)
Batteries
Station Message
Detail Recording (SMDR)
PSU-S/M/L*1
(KX-TDA0108/
KX-TDA0104/
KX-TDA0103)
External Sensor/External Relay Device
MSG4
(KX-TDA0191)
MPR
(Installed by default)
MEC
(KX-TDA0105)
Server PC*2
RMT
(KX-TDA0196)
Amplifier
Radio
PC
22
Installation Manual
KX-T7600 KX-T7600
DPT
DPT
Fax Machine
LAN
Private
IP Network
PC
MSLC16
(KX-TDA0175)
E&M8
(KX-TDA0184)
PRI30
(KX-TDA0290
CE/CJ)
KX-T7600
DPT
DLC8
(KX-TDA0171)
SLT
T1 Line
(Digital Trunk)
KX-T7600
DPT
PC
Mountable Equipment
Pager/Speaker
PC
1.2 Basic System Construction
*1
*2
The KX-TDA100CN and KX-TDA200CN have a power supply unit (PSU-S and PSU-M, respectively)
pre-installed.
Only 1 Server PC can be connected to the Hybrid IP-PBX. Two or more Server PCs cannot be used
simultaneously.
Installation Manual
23
1.3 Options
1.3
Options
1.3.1
Options
Model No.
Model Name
Description
KX-TDA0105
Memory Expansion Card (MEC)
KX-TDA0143
4 Cell Station Interface Card (CSIF4) 4-port CS interface card for 4 CSs.
KX-TDA0144
8 Cell Station Interface Card (CSIF8) 8-port CS interface card for 8 CSs.
KX-TDA0161
4-Port Doorphone Card (DPH4)
4-port doorphone card for 4 doorphones and 4 door
openers. To be mounted on the OPB3 card.
KX-TDA0162
2-Port Doorphone Card (German
Type) (DPH2)
2-port doorphone card for 2 German type
doorphones and 2 door openers. To be mounted on
the OPB3 card.
KX-TDA0164
4-Port External Input/Output Card
(EIO4)
4-port external input/output card. To be mounted on
the OPB3 card.
KX-TDA0166
16-Channel Echo Canceller Card
(ECHO16)
16-channel card for echo cancellation during
conferences. To be mounted on the OPB3 card.
KX-TDA0168
Extension Caller ID Card (EXT-CID)
Sends Caller ID signals to extension ports. To be
mounted on the SLC8 card.
KX-TDA0170
8-Port Digital Hybrid Extension Card 8-port digital hybrid extension card for DPTs, APTs,
(DHLC8)
SLTs, DSS consoles, and PT-interface CSs, with 2
power failure transfer (PFT) ports.
KX-TDA0171
8-Port Digital Extension Card (DLC8) 8-port digital extension card for DPTs, DSS
consoles, and PT-interface CSs.
KX-TDA0172
16-Port Digital Extension Card
(DLC16)
16-port digital extension card for DPTs, DSS
consoles, and PT-interface CSs.
KX-TDA0173
8-Port Single Line Telephone
Extension Card (SLC8)
8-port extension card for SLTs with 2 power failure
transfer (PFT) ports.
KX-TDA0174
16-Port Single Line Telephone
Extension Card (SLC16)
16-port extension card for SLTs with 4 power failure
transfer (PFT) ports.
KX-TDA0175
16-Port Single Line Telephone
Extension with Message Lamp Card
(MSLC16)
16-port extension card for SLTs with Message
Waiting Lamp control and 4 power failure transfer
(PFT) ports. Maximum power output of 160 V/90 V
for Message Waiting Lamp control.
KX-TDA0180
8-Port Analogue Trunk Card (LCOT8) 8-port analogue trunk card with 2 power failure
transfer (PFT) ports.
KX-TDA0181
16-Port Analogue Trunk Card
(LCOT16)
24
Installation Manual
Memory expansion card to increase system data
storage space, enable Broadcasting and Call Billing
for Guest Room features, and double the number of
DPTs, using Digital XDP connection. To be mounted
on the MPR card.
16-port analogue trunk card with 4 power failure
transfer (PFT) ports.
1.3 Options
Model No.
Model Name
Description
KX-TDA0182
8-Port DID Card (DID8)
8-port DID trunk card.
KX-TDA0183
4-Port Analogue Trunk Card (LCOT4) 4-port analogue trunk card with 2 power failure
transfer (PFT) ports.
KX-TDA0184
8-Port E & M Trunk Card (E&M8)
8-port E & M (TIE) trunk card. Type 5 support.
KX-TDA0187
T-1 Trunk Card (T1)
1-port T1 trunk card. EIA/TIA standard compliant.
KX-TDA0188
E-1 Trunk Card (E1)
1-port E1 trunk card. ITU-T standard compliant.
KX-TDA0189
8-Port Caller ID/Pay Tone Card (CID/ 8-port Caller ID signal type FSK/FSK (with Call
PAY8)
Waiting Caller ID [Visual Caller ID])/DTMF, and 8
ports of Pay Tone Service (12 kHz/16 kHz). To be
mounted on the LCOT8/LCOT16 cards.
KX-TDA0190
Optional 3-Slot Base Card (OPB3)
Optional 3-slot base card for mounting a maximum
of 3 option cards from the following: MSG4, DPH4,
DPH2, or ECHO16 card.
KX-TDA0191
4-Channel Message Card (MSG4)
4-channel message card. To be mounted on the
OPB3 card.
KX-TDA0193
8-Port Caller ID Card (CID8)
8-port Caller ID signal type FSK/FSK (with Call
Waiting Caller ID [Visual Caller ID])/DTMF. To be
mounted on the LCOT8/LCOT16 cards.
KX-TDA0196
Remote Card (RMT)
Analogue modem card for remote communication
with the Hybrid IP-PBX. V90 support. To be
mounted on the MPR card.
KX-TDA0284
4-Port BRI Card (BRI4)
4-port ISDN Basic Rate Interface card with 1 power
failure transfer port. EURO-ISDN/ETSI compliant.
KX-TDA0288
8-Port BRI Card (BRI8)
8-port ISDN Basic Rate Interface card with 1 power
failure transfer port. EURO-ISDN/ETSI compliant.
KX-TDA0290CE/CJ PRI Card (PRI30)
1-port ISDN Primary Rate Interface card (30B
channels). EURO-ISDN/ETSI compliant.
KX-TDA0290
PRI Card (PRI23)
1-port ISDN Primary Rate Interface card (23B
channels). NI (North American standard ISDN
protocol) compliant.
KX-TDA0410
CTI Link Card (CTI-LINK)
Ethernet card for CTI communication via 10BASE-T
port. CSTA Phase 3 protocol compatible.
KX-TDA0470
16-Channel VoIP Extension Card (IP- 16-channel VoIP extension card. Compliant with
EXT16)
Panasonic proprietary protocol, and ITU-T G.729a
and G.711 CODEC methods.
KX-TDA0480
4-Channel VoIP Gateway Card (IPGW4)
4-channel VoIP gateway card. Compliant with VoIP
H.323 V.2 protocol, and ITU-T G.729a and G.723.1
CODEC methods. G3 fax support.
KX-TDA0484
4-Channel VoIP Gateway Card (IPGW4E)
4-channel VoIP gateway card. Compliant with VoIP
H.323 V.2 protocol, and ITU-T G.729a, G.723.1, and
G.711 CODEC methods.
Installation Manual
25
1.3 Options
Model No.
Model Name
Description
KX-TDA0490
16-Channel VoIP Gateway Card (IP- 16-channel VoIP gateway card. Compliant with VoIP
GW16)
H.323 V.2 protocol, and ITU-T G.729a, G.723.1, and
G.711 CODEC methods.
KX-TDA0103
L-Type Power Supply Unit (PSU-L)
Power Supply Unit for KX-TDA200. Total power
output of 279 W. Safety Class 1 compliant.
KX-TDA0104
M-Type Power Supply Unit (PSU-M)
Power Supply Unit for KX-TDA100 and KX-TDA200.
Total power output of 140.4 W. Safety Class 1
compliant.
KX-TDA0108
S-Type Power Supply Unit (PSU-S)
Power Supply Unit for KX-TDA100. Total power
output of 74 W. Safety Class 1 compliant.
KX-TDA0820
SD Memory Card for Software
Upgrade
Optional SD Memory Card to upgrade the Hybrid IPPBX with software version 1 or 1.1 to version 2.0.
KX-TDA0920
SD Memory Card for Software
Upgrade to Enhanced Version
Optional SD Memory Card to upgrade the Hybrid IPPBX with software version 1 or 1.1 to version 2.0,
and for NDSS feature and CTI enhancement.
26
Installation Manual
1.4 Specifications
1.4
Specifications
1.4.1
General Description
Control Bus
Original bus (16-bit, 8 MHz, 10 megabytes per second)
Communication Bus
H.100 bus conformity (1024 time slot)
Switching
Non-blocking
Power Input
PSU-S
100 V AC to 130 V AC, 1.4 A/200 V AC to 240 V AC, 0.8 A,
50 Hz/60 Hz
PSU-M
100 V AC to 130 V AC, 2.5 A/200 V AC to 240 V AC, 1.4 A,
50 Hz/60 Hz
PSU-L
100 V AC to 130 V AC, 5.1 A/200 V AC to 240 V AC, 2.55 A,
50 Hz/60 Hz
External Battery
+36 V DC (+12 V DC × 3, battery capacity of 28 Ah or below
recommended for each external battery)
Maximum Power Failure Tolerance
300 ms (without using backup batteries)
Memory Backup Duration
7 years
Dialling
Trunk
Dial Pulse (DP) 10 pps, 20 pps
Tone (DTMF) Dialling
Extension
Dial Pulse (DP) 10 pps, 20 pps
Tone (DTMF) Dialling
Mode Conversion
DP-DTMF, DTMF-DP
Ring Frequency
20 Hz/25 Hz (selectable)
Trunk Loop Limit
1600 Ω maximum
Operating
Environment
Temperature
0 °C to 40 °C
Humidity
10 % to 90 % (non-condensing)
Conference Call Trunk
From 10 × 3-party conference call to 4 × 8-party conference
call
Music on Hold (MOH)
2 ports (Level Control: -11 dB to +11 dB in 1 dB steps)
MOH1: External Music Source port
MOH2: Selectable Internal/External Music Source port
Paging
Serial Interface Port
Internal
Level Control: -15 dB to +6 dB in 3 dB steps
External
2 ports (Volume Control: -15 dB to +15 dB in 1 dB steps)
RS-232C
1 (maximum 115.2 kbps)
USB
1
Installation Manual
27
1.4 Specifications
Extension Connection Cable
Dimension
Weight (when fully
mounted)
28
Installation Manual
SLT
1-pair wire (T, R)
DPT
1-pair wire (D1, D2) or
2-pair wire (T, R, D1, D2)
APT
2-pair wire (T, R, D1, D2)
PT-interface CS
1-pair wire (D1, D2)
DSS Console and Add-on
Key Module
1-pair wire (D1, D2)
KX-TDA100
334 mm (W) × 390 mm (H) × 270 mm (D)
KX-TDA200
430 mm (W) × 415 mm (H) × 270 mm (D)
KX-TDA100
Under 12 kg
KX-TDA200
Under 16 kg
1.4 Specifications
1.4.2
Characteristics
PT: KX-T7600 series: 90 Ω; all other DPTs/APTs: 40 Ω
SLT: 60 Ω including set
Doorphone: 20 Ω
CS: 130 Ω; PT-interface CS: 65 Ω
Terminal Equipment Loop Limit
•
•
•
•
Minimum Leakage Resistance
15 000 Ω minimum
Maximum Number of Extension
Instruments per Line
1 for PT or SLT
2 by Parallel or eXtra Device Port connection of an APT/DPT and an SLT
3 by Digital eXtra Device Port connection of two DPTs and an SLT
Ring Voltage
75 Vrms at 20 Hz/25 Hz depending on the Ringing Load
Trunk Loop Limit
1600 Ω maximum
Hookswitch Flash/Recall Timing
Range
24 ms to 2032 ms
BRI Cards Internal ISDN Mode
Supply Voltage: 40 V
Power Supply: 4.5 W per 1 line, 10 W per 4 lines (BRI4)
4.5 W per 1 line, 20 W per 8 lines (BRI8)
Power Supply Method: Phantom Power Supply
Door Opener Current Limit
24 V DC/30 V AC, 1 A maximum
External Relay Current Limit
24 V DC/30 V AC, 1 A maximum
External Sensor Current Limit
Power to the external sensor is provided from the EIO4 card and must be
grounded through the EIO4 card. For the connection diagram, refer to
"2.6.4 EIO4 Card". The Hybrid IP-PBX detects input from the sensor when
the signal is under 100 Ω.
Paging Terminal Impedance
600 Ω
MOH (Music on Hold) Terminal
Impedance
10 000 Ω
Installation Manual
29
1.4 Specifications
1.4.3
System Capacity
Maximum Optional Service Cards
There are 2 types of optional service cards for installation:
•
Cards installed in the slots of the Hybrid IP-PBX
•
Cards mounted on other optional service cards
Notes
•
•
Any card that exceeds the capacity of the Hybrid IP-PBX will be ignored.
When the Hybrid IP-PBX starts up with an invalid configuration, some cards will be ignored.
Cards Installed in the Slots of the Hybrid IP-PBX
KX-TDA100
KX-TDA200
MPR Card Slot
MPR Card Slot
Free Slots 1 to 10
Free Slots 1 to 5
Option Card Slot
30
Installation Manual
Option Card Slot
1.4 Specifications
The following number of optional service cards can be installed in the various slots of the Hybrid IP-PBX.
Maximum Number
Card Type
MPR
Trunk Card
Installed in
KX-TDA100
KX-TDA200
1
1
Total 4*1
Total 8*1
4
8
2
4
MPR Card Slot
LCOT4
LCOT8
LCOT16
DID8
E&M8
BRI4
BRI8
T1
E1
PRI23
PRI30
IP-GW4
IP-GW4E
Free Slot
2
4
Total 4
Total 8
4
8
2
4
IP-GW16
Extension Card
DHLC8
DLC8
DLC16
SLC8
SLC16
MSLC16
IP-EXT16
CSIF4
CSIF8
Installation Manual
31
1.4 Specifications
Maximum Number
Card Type
Installed in
KX-TDA100
KX-TDA200
OPB3
2
4
CTI-LINK
1
1
Option Card Slot/Free Slot
*1
One T1, E1, PRI30, PRI23, or IP-GW4 card counts as 2 cards. However, one IP-GW4E card counts as 1 card.
Cards Mounted on Other Optional Service Cards
The following number of optional service cards can be mounted on the specified other optional service
cards.
Maximum Number
Card Type
Mounted on
KX-TDA100
KX-TDA200
MEC
1
1
RMT
1
1
8
16
LCOT8 Card/LCOT16 Card
EXT-CID
4
8
SLC8 Card
DPH4
2
4
DPH2
4
8
2*1
4*1
MSG4
2
4
EIO4
2
4
MPR Card
CID/PAY8
CID8
ECHO16
*1
32
Only 1 ECHO16 card can be mounted on each OPB3 card.
Installation Manual
OPB3 Card
1.4 Specifications
Maximum Terminal Equipment
The following number of items of terminal equipment can be supported by the Hybrid IP-PBX. For how to
count the total number of items of equipment to be connected, refer to "MEC Card Calculation".
Terminal Equipment Type
KX-TDA100
KX-TDA200
Without MEC
Card
With MEC
Card
Without MEC
Card
With MEC
Card
88
152
176
304
SLT, APT, DPT and IP-PT
64
128
128
256
SLT
64
64
128
128
APT/DPT
64
128
128
256
IP-PT
64
64
128
128
Telephone*1
DSS console
8
8
CS
16
32
PS
128
128
Voice Processing System (VPS)
2
2
Doorphone
8
16
Door Opener
8
16
External Sensor
8
16
External Relay
8
16
Add-on Key Module
64
USB Module
*1
128
64
128
256
128
A single "T1-OPX (Off Premise Extension) port" or "BRI/PRI extension port" is counted as a wired telephone.
MEC Card Calculation
Calculate the MEC figure from the type and total number of items of equipment to be connected. If the MEC
figure exceeds 64 (for KX-TDA100) or 128 (for KX-TDA200), you need to install an MEC card.
MEC Card Calculation
Equipment Type
PT
MEC Figure
KX-T7600 series DPT/DSS console
1
KX-T7560/KX-T7565 DPT
1
Other DPT/DSS console
1
APT
1
IP-PT
1
Installation Manual
33
1.4 Specifications
Equipment Type
Extension Card*1
MEC Figure
DHLC8
8
SLC8
8
SLC16
16
MSLC16
16
CS (1 unit)
0
PT-interface CS (1 unit)
0
ISDN Extension
0
VPS (1 port)
1
*1
Only the extension cards that can support SLTs count for the MEC figures.
Calculation Example (KX-TDA100)
Equipment Type
MEC Figure
KX-T7600 series DPT
48 units
48
SLC16
1 card
16
MSLC16
1 card
16
VPS
8 ports
8
Total
88
The total MEC figure is 88. As this exceeds 64, you need to install an MEC card for this configuration.
Power Supply Unit Selection
The Hybrid IP-PBX needs an optional power supply unit (PSU) suitable for its configuration. Calculate the
load figure from the type and number of items of equipment to be connected, and determine the type of PSU
that will be required.
Load Figure Calculation
Equipment Type
PT
Extension Card*1
34
Installation Manual
Load Figure
KX-T7600 series DPT/DSS console
1
KX-T7560/KX-T7565 DPT
1
Other DPT/DSS console
4
APT
4
IP-PT
0
DHLC8
8
SLC8
8
SLC16
16
MSLC16
16
1.4 Specifications
Equipment Type
Load Figure
CS (1 unit)
4
PT-interface CS (1 unit)
4
ISDN Extension
2
VPS (1 port)
1
*1
Only the extension cards that can support SLTs count for the load figures.
PSU Capability
Each PSU supports a different amount of load figures.
PSU Type
Maximum Load Figures
PSU-S*1
64
PSU-M*2
128
PSU-L*3
512
*1
*2
*3
Available for the KX-TDA100
Available for the KX-TDA100 and KX-TDA200
Available for the KX-TDA200
Calculation Example (KX-TDA200)
Equipment Type
Load Figure
KX-T7600 series DPT
48 units
48
Other DPT
2 units
8
SLC16
1 card
16
MSLC16
1 card
16
VPS
8 ports
8
Total
96
The total load figure is 96. As this is between 64 and 128, you should install the PSU-M. But if you expect
expansion in the future, it may be better to install the PSU-L. There is no harm in installing a PSU that is
larger than is required for the current configuration.
Installation Manual
35
1.4 Specifications
36
Installation Manual
Section 2
Installation
This section describes the procedures to install the Hybrid IPPBX. Detailed instructions for planning the installation site,
installing the shelves and optional service cards, and cabling
of peripheral equipment are provided. Further information on
system expansion and peripheral equipment installation is
included.
Installation Manual
37
2.1 Before Installation
2.1
Before Installation
2.1.1
Before Installation
Please read the following notes concerning installation and connection before installing the Hybrid IP-PBX.
Be sure to comply with applicable local regulations (e.g., law, guidelines).
Safety Installation Instructions
When installing telephone wiring, basic safety precautions should always be followed to reduce the risk of
fire, electric shock and injury to persons, including the following:
1. Never install telephone wiring during a lightning storm.
2. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
3. Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected
at the network interface.
4. Use caution when installing or modifying telephone lines.
5. Anti-static precautions should be taken during installation.
Installation Precautions
This set is made for wall mounting (KX-TDA100/KX-TDA200) or floor standing (KX-TDA200 only). Avoid
installing in the following places. (Doing so may result in malfunction, noise, or discolouration.)
1. In direct sunlight and hot, cold, or humid places.
Temperature range: 0 °C to 40 °C
2. Sulphuric gases produced in areas where there are thermal springs, etc. may damage the equipment
or contacts.
3.
4.
5.
6.
Places in which shocks or vibrations are frequent or strong.
Dusty places, or places where water or oil may come into contact with the unit.
Near high-frequency generating devices such as sewing machines or electric welders.
On or near computers, telexes, or other office equipment, as well as microwave ovens or air
conditioners. (It is preferable not to install in the same room with the above equipment.)
7. Closer than 1.8 m to radios and televisions (both the Hybrid IP-PBX and PTs).
8. Do not obstruct the area around the Hybrid IP-PBX (for reasons of maintenance and inspection—be
especially careful to allow at least 20 cm above and 10 cm at the sides of the Hybrid IP-PBX for cooling).
9. Do not block the openings at top of the Hybrid IP-PBX.
10. Do not stack up the optional service cards.
Wiring Precautions
Be sure to follow these instructions when wiring.
1. Do not wire the telephone cable in parallel with an AC power source, computer, telex, etc. If the cables
are run near those wires, shield the cables with metal tubing or use shielded cables and ground the
shields.
2. If cables are run on the floor, use protectors to prevent the wires from being stepped on. Avoid wiring
under carpets.
38
Installation Manual
2.1 Before Installation
3. Avoid using the same power supply outlet for computers, telexes, and other office equipment.
Otherwise, the Hybrid IP-PBX operation may be interrupted by the inducted noise from such
equipment.
4. Please use 1-pair telephone wire for extension connection of (telephone) equipment such as standard
telephones, data terminals, answering machines, computers, Voice Processing Systems, etc., except
PTs (e.g., KX-T7600 series).
5. The power switch and battery switch of the Hybrid IP-PBX must be off during wiring. After the wiring is
completed, turn the power switch on.
6. Mis-wiring may cause the Hybrid IP-PBX to operate improperly.
7. If an extension does not operate properly, disconnect the telephone from the extension line and then
connect again, or turn the power to the Hybrid IP-PBX off and on again.
8. The Hybrid IP-PBX is equipped with a 3-wire earthing type plug. This is a safety feature. If you are
unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not
defeat the purpose of the earthing-type plug.
9. Use twisted pair cable for trunk connection.
10. Trunks should be installed with surge protectors. For details, refer to "2.2.14 Surge Protector
Installation".
Installation Manual
39
2.2 Installation of the Hybrid IP-PBX
2.2
Installation of the Hybrid IP-PBX
2.2.1
Unpacking
Unpack the box and check the items below:
KX-TDA100
KX-TDA200
Main Unit
1
1
AC Cord with a Ferrite Core*1
1
1
Metal Bracket
1
1
Screw A
3
4
Screw B (Black)
2
6
Anchor Plug
3
4
Mini Plug (for pager and music source)
4
4
SD Memory Card
1
1
*1
40
In Canada, there is no ferrite core attached to the AC cord.
Installation Manual
2.2 Installation of the Hybrid IP-PBX
2.2.2
Names and Locations
Inside View
KX-TDA100
KX-TDA200
RS-232C Port
RS-232C Port
USB Port
USB Port
ALARM Indicator
RUN Indicator
ALARM Indicator
RUN Indicator
PSU Slot
MPR Card Slot
Null Slot*
PSU Slot
MPR Card Slot
Free Slots 1 to 10
Free Slots 1 to 5
Option Card Slot
Option Card Slot
Note
* Null slot is not available for any optional service card.
Installation Manual
41
2.2 Installation of the Hybrid IP-PBX
2.2.3
Opening/Closing the Front Cover
Opening the Front Cover
1. Insert a flathead screwdriver into the opening (on the left of the screw cover) and unlatch the screw
cover.
Screw Cover
2. Turn the screw anticlockwise to loosen.
3. Slide the front cover to the right until it stops, then lift the front cover.
42
Installation Manual
2.2 Installation of the Hybrid IP-PBX
Closing the Front Cover
1. Hook the front cover onto the cabinet (line up the protrusions on the cover with the receptacles on the
cabinet). Then slide the front cover to the left until it locks.
2. Turn the screw clockwise to tighten.
3. Secure the screw cover.
2
1
Notes
•
•
For safety reasons, close the front cover and tighten the screw when the Hybrid IP-PBX is in
operation.
Do not forget to tighten the screw before securing the screw cover.
Installation Manual
43
2.2 Installation of the Hybrid IP-PBX
2.2.4
Installing/Replacing the Power Supply Unit
Function
PSU Type
Lower/Upper Input Voltage Range
Current
PSU-S
(for KX-TDA100)
Lower: 100 V AC to 130 V AC
1.4 A
Upper: 200 V AC to 240 V AC
0.8 A
PSU-M
(for KX-TDA100/200)
Lower: 100 V AC to 130 V AC
2.5 A
Upper: 200 V AC to 240 V AC
1.4 A
PSU-L
(for KX-TDA200)
Lower: 100 V AC to 130 V AC
5.1 A
Upper: 200 V AC to 240 V AC
2.55 A
Input Frequency
50 Hz or 60 Hz
PSU-S
PSU-M/PSU-L
Battery Switch
Battery Switch
Battery Connector
Battery Connector
Earth Terminal
Power Switch
Earth Terminal
AC Inlet
Power Switch
AC Inlet
Accessory and User-supplied Items
Accessory (included): Screws × 4
User-supplied (not included): earthing wire, Back-up Battery Cable (KX-A228 for PSU-S and PSU-M, or
KX-A229 for PSU-L)
Notes
•
•
For details about frame earth connection, refer to "2.2.5 Frame Earth Connection".
For details about backup batteries connection, refer to "2.2.6 Backup Batteries Connection".
Safety Instructions
Each PSU complies with Safety Class 1 of IEC60950, EN60950, UL60950,
CAN/CSA-C22.2 No.60950, and AS/NZS60950; therefore a protective earth connection exists between the
mains outlet ground and the PSU case. To ensure the PBX chassis is safely grounded, it is essential that
the PSU case be securely fastened to the PBX chassis with the 4 screws provided with each PSU.
When installing or replacing PSU, basic safety precautions should always be followed to reduce the risk of
fire, electric shock and injury to persons, including the following:
1. Never install or replace PSU during a lightning storm.
2. Never install or replace PSU in wet locations.
44
Installation Manual
2.2 Installation of the Hybrid IP-PBX
3. Never install or replace PSU unless at least 20 s has elapsed after the AC supply and backup
battery supply are disconnected.
4. To protect the back board from static electricity, do not touch parts on the back board in the main
unit and PSU. To discharge static electricity, touch ground or wear an earthing strap.
The following procedures are for installing or replacing a PSU only. Do not replace or remove the
PSU for any other purpose.
Installing the Power Supply Unit
1. Insert the PSU along the guide rails.
CAUTION
For safety reasons, do not touch parts in the PSU.
Guide Rail
Installation Manual
45
2.2 Installation of the Hybrid IP-PBX
2. Push the release lever in the direction of the arrow, so that the PSU engages securely with the
connector on the back board.
Back Board
Release Lever
3. Turn the 4 screws clockwise, in the order indicated by the numbers 1 to 4, to fix the PSU.
3 2
Screws
4 1
Replacing the Power Supply Unit
1. Unplug the AC power cord and Back-up Battery Cable.
46
Installation Manual
2.2 Installation of the Hybrid IP-PBX
2. Turn the 4 screws anticlockwise to loosen them.
Screws
3. Pull the release lever in the direction of the arrow to disconnect the PSU from the back board.
Back Board
Release Lever
4. Replace the PSU.
New PSU
Current PSU
5. Follow the steps in "Installing the Power Supply Unit".
Installation Manual
47
2.2 Installation of the Hybrid IP-PBX
2.2.5
Frame Earth Connection
IMPORTANT
Connect the frame of the Hybrid IP-PBX to earth.
1. Loosen the screw.
2. Insert an earthing wire (user-
Screw
supplied)*.
3. Tighten the screw.
4. Connect the earthing wire to
earth.
Earthing
wire
To earth
* For earthing wire, green-and-yellow insulation is required, and the cross-sectional area of the conductor
must be more than 0.75 mm2 or 18 AWG.
•
•
•
48
Be sure to comply with applicable local regulations (e.g., law, guidelines).
Proper earthing (connection to earth) is very important to protect the Hybrid IP-PBX from the bad
effects of external noise or to reduce the risk to the user of electrocution in the case of lightning strike.
The earthing wire of the AC cable has an effect against the external noise and lightning strikes, but it
may not be enough to protect the Hybrid IP-PBX. A permanent connection between earth and the earth
terminal of the Hybrid IP-PBX must be made.
Installation Manual
2.2 Installation of the Hybrid IP-PBX
2.2.6
Backup Batteries Connection
The backup batteries and Back-up Battery Cable (KX-A228 for PSU-S and PSU-M, or KX-A229 for PSU-L)
provide a backup power supply to allow full use of the Hybrid IP-PBX in the event of a power failure. In case
of power failure, the backup batteries automatically maintain the power to the Hybrid IP-PBX without
interruption.
1. Turn off the battery switch on the PSU.
2. Connect the Back-up Battery Cable with 3 identical VRLA (Valve Regulated Lead Acid) batteries (12 V
DC × 3).
ON
Battery Switch
Battery Connector
OFF
Back-up Battery Cable
Fuse
Red
Black
Backup Batteries (12 V DC x 3)
•
•
•
•
•
Turn on the battery switch on the PSU only after the installation of the Hybrid IP-PBX is finished and
AC power is available.
For each backup battery, battery capacity of 28 Ah or below is recommended (otherwise, the battery
charge may not be maintained).
Make sure that the type and capacity of the 3 backup batteries are identical.
The Back-up Battery Cable should not be exposed to direct sunlight. Keep the Back-up Battery Cable
and the backup batteries away from heating appliances and fire. Place the backup batteries in
ventilated place.
For details about the backup batteries, refer to the manual intended for the batteries.
CAUTION
•
•
•
•
•
Be sure to comply with applicable local regulations (e.g., law, guidelines).
Make sure that the polarities of the backup batteries and wiring are correct.
Make sure that you do not short the backup batteries or cables.
There is a danger of explosion if backup batteries are incorrectly replaced. Replace only with the
same or equivalent type recommended by the battery manufacturer. Dispose of used batteries
according to the manufacturer's instructions.
Use the correct type of Back-up Battery Cable for the type of the PSU.
Installation Manual
49
2.2 Installation of the Hybrid IP-PBX
2.2.7
Installing/Removing the Optional Service Cards
CAUTION
To protect the back board from static electricity, do not touch parts on the back board in the main unit
and on the optional service cards. To discharge static electricity, touch ground or wear an earthing strap.
Note
The optional service cards can be installed or removed while the DC power is supplied. However, when
installing or removing the MPR card, the DC power supply must be turned off.
Installing Optional Service Cards
1. Insert the card along the guide rails.
Guide Rail
50
Installation Manual
2.2 Installation of the Hybrid IP-PBX
2. Holding the card as shown below, push the release lever in the direction of the arrow so that the card
engages securely with the connector on the back board.
Back Board
Release Lever
3. Turn the 2 screws clockwise to fix the card in place.
Screws
Note
Make sure the screws are tightened to earth the card securely.
Installation Manual
51
2.2 Installation of the Hybrid IP-PBX
Covering the Blank Slots
Be sure to cover each slot in which no optional service card is installed by using a Blank Slot Cover.
CAUTION
Failure to install the Blank Slot Cover may cause electromagnetic interferences.
52
Installation Manual
2.2 Installation of the Hybrid IP-PBX
Handling of the Cables
When cables are connected to the Hybrid IP-PBX, run the cables to either right or left and then towards the
backside of the cabinet as shown below.
1
2
4
3
Note
For safety reasons, do not stretch, bend, or pinch the AC power cord.
Installation Manual
53
2.2 Installation of the Hybrid IP-PBX
Removing the Optional Service Cards
1. Turn the 2 screws anticlockwise to loosen them.
Screws
2. Pull the release lever in the direction of the arrow to disconnect the card from the back board. Pull the
card from the cabinet to remove it.
Back Board
Release Lever
54
Installation Manual
2.2 Installation of the Hybrid IP-PBX
2.2.8
Types of Connectors
Connector Type
Pin Number
RJ11
1
4
(Twisted pair cable)
RJ45
8
1
(Twisted pair cable)
BNC
Used for
•
•
•
•
•
•
•
DHLC8 (KX-TDA0170)
SLC8 (KX-TDA0173)
SLC16 (KX-TDA0174)
MSLC16 (KX-TDA0175)
LCOT8 (KX-TDA0180)
LCOT16 (KX-TDA0181)
LCOT4 (KX-TDA0183)
•
•
•
•
•
•
•
•
•
•
•
•
•
CSIF4 (KX-TDA0143)
CSIF8 (KX-TDA0144)
T1 (KX-TDA0187)
E1 (KX-TDA0188)
BRI4 (KX-TDA0284)
BRI8 (KX-TDA0288)
PRI30 (KX-TDA0290CE/CJ)
PRI23 (KX-TDA0290)
CTI-LINK (KX-TDA0410)
IP-EXT16 (KX-TDA0470)
IP-GW4 (KX-TDA0480)
IP-GW4E (KX-TDA0484)
IP-GW16 (KX-TDA0490)
•
•
E1 (KX-TDA0188)
PRI30 (KX-TDA0290CE/CJ)
•
•
•
•
•
•
•
•
•
•
•
DHLC8 (KX-TDA0170)
DLC8 (KX-TDA0171)
DLC16 (KX-TDA0172)
SLC8 (KX-TDA0173)
SLC16 (KX-TDA0174)
MSLC16 (KX-TDA0175)
LCOT8 (KX-TDA0180)
LCOT16 (KX-TDA0181)
DID8 (KX-TDA0182)
LCOT4 (KX-TDA0183)
E&M8 (KX-TDA0184)
1
2
Amphenol
Type A Type B
(Shielded twisted pair
cable)
50
25
26
1
Installation Manual
55
2.2 Installation of the Hybrid IP-PBX
Connector Type
10-pin
8-pin
Terminal Terminal
Block
Block
Pin Number
1
1
10
Used for
•
•
•
DPH4 (KX-TDA0161)
DPH2 (KX-TDA0162)
EIO4 (KX-TDA0164)
•
•
IP-GW4 (KX-TDA0480)
Basic Shelf
•
MPR
•
MPR
8
RS-232C
6
1
9
5
USB
3
2
4
1
Mini Plug
2
4
56
Installation Manual
2.2 Installation of the Hybrid IP-PBX
2.2.9
Attaching a Ferrite Core
A ferrite core must be attached when:
•
connecting T1, E1, PRI, BRI, IP-GW16, and IP-EXT16 cards using an RJ45 connector (except in
Canada, where the ferrite core is not necessarily required), or
•
connecting extension cards using an Amphenol connector.
The ferrite core is included with the card.
When connecting a T1/E1/PRI/IP-GW16/IP-EXT16 card
Wrap the cable once around the ferrite core, then close the case of the ferrite core. Attach the ferrite core 5
cm away from the connector.
5 cm
When connecting a BRI card
Attach the ferrite core, then close the case of the ferrite core. Attach the ferrite core as close to the card's
connector as possible.
When only 1 or 2 cables are used for connection, wrap the
cable(s) once around the ferrite core.
When 3 or 4 cables are used for connection, simply pass the
cables through the ferrite core.
Installation Manual
57
2.2 Installation of the Hybrid IP-PBX
Note
For every 4 cables, use 1 ferrite core; a ferrite core holds a maximum of 4 cables.
When connecting an extension card
Pass the cable through the ferrite core, then close the case of the ferrite core. Attach the ferrite core 3 cm
away from the connector.
3 cm
If you need to open the ferrite core, use a flathead screwdriver to unlatch the case of the ferrite core.
58
Installation Manual
2.2 Installation of the Hybrid IP-PBX
2.2.10 Fastening Amphenol Type Connector
An Amphenol 57JE type connector is used on some of the optional service cards.
To connect an Amphenol connector, use the spring latch or screw to fix the upper part and use Velcro® tape
to fix the lower part of the connector.
Type A (Spring Latch + Velcro Tape)
Type B (Screw + Velcro Tape)
Velcro
Tape
Velcro
Tape
1
Spring
Latch
Remove the
screw on the
optional service
card.
2
Spring
Latch
1
1
Insert the screw (included
with the Amphenol or
optional service card).
2
2
Installation Manual
59
2.2 Installation of the Hybrid IP-PBX
Amphenol Connector Pin Assignment Chart
Below is an Amphenol connector pin assignment chart for all optional service cards that use the Amphenol
connector. For more details, refer to the appropriate section in "2.4 Installation of the Trunk Cards" and "2.5
Installation of the Extension Cards".
Pin No.
1
26
2
27
3
28
4
29
5
30
6
31
7
32
8
33
9
34
10
35
11
36
12
37
13
38
14
39
15
40
16
41
17
42
18
43
19
44
20
45
21
46
22
47
23
48
24
49
25
50
60
LCOT4
RA
TA
RB
TB
RC
TC
RD
TD
Installation Manual
LCOT8
RA
TA
RB
TB
RC
TC
RD
TD
RE
TE
RF
TF
RG
TG
RH
TH
LCOT16
RA
TA
RB
TB
RC
TC
RD
TD
RE
TE
RF
TF
RG
TG
RH
TH
RI
TI
RJ
TJ
RK
TK
RL
TL
RM
TM
RN
TN
RO
TO
RP
TP
DID8
RA
TA
RB
TB
RC
TC
RD
TD
RE
TE
RF
TF
RG
TG
RH
TH
E&M8
TA
RA
T1A
R1A
EA
MA
SGA
SGB
TB
RB
T1B
R1B
EB
MB
TC
RC
T1C
R1C
EC
MC
TD
RD
T1D
R1D
ED
MD
TE
RE
T1E
R1E
EE
ME
TF
RF
T1F
R1F
EF
MF
TG
RG
T1G
R1G
EG
MG
TH
RH
T1H
R1H
EH
MH
DHLC8
RA
TA
D2A
D1A
RB
TB
D2B
D1B
RC
TC
D2C
D1C
RD
TD
D2D
D1D
RE
TE
D2E
D1E
RF
TF
D2F
D1F
RG
TG
D2G
D1G
RH
TH
D2H
D1H
DLC8
D2A
D1A
D2B
D1B
D2C
D1C
D2D
D1D
D2E
D1E
DLC16
D2A
D1A
D2B
D1B
D2C
D1C
D2D
D1D
D2E
D1E
D2F
D1F
D2G
D1G
D2H
D1H
D2I
D1I
D2J
D1J
D2K
D1K
D2L
D1L
D2M
D1M
D2N
D1N
D2O
D1O
D2P
D1P
MSLC16
RA
TA
RB
TB
RC
TC
RD
TD
RE
TE
RF
TF
RG
TG
RH
TH
RI
TI
RJ
TJ
RK
TK
RL
TL
RM
TM
RN
TN
RO
TO
RP
TP
SLC16
RA
TA
RB
TB
RC
TC
RD
TD
RE
TE
RF
TF
RG
TG
RH
TH
RI
TI
RJ
TJ
RK
TK
RL
TL
RM
TM
RN
TN
RO
TO
RP
TP
SLC8
RA
TA
RB
TB
RC
TC
RD
TD
RE
TE
RF
TF
D2F
D1F
RG
TG
D2G
D1G
RH
TH
D2H
D1H
2.2 Installation of the Hybrid IP-PBX
2.2.11 Wall Mounting (KX-TDA200)
CAUTION
Drive mounting screws into the wall. Be careful to avoid touching any metal laths, wire laths or metal
plates in the wall.
1. Install 4 anchor plugs in the wall, using the metal bracket as a template. Fix the metal bracket with 4
screws (A).
Anchor Plug
Wall
Hammer
Anchor Plug
Metal Bracket
6.5 mm
30 mm
TOP
TOP
Screw (A)
Screw (A)
Metal Bracket
Installation Manual
61
2.2 Installation of the Hybrid IP-PBX
2. Hook the cabinet onto the metal bracket, making sure that the unit slides down and onto the hooked
parts of the metal bracket. Use 2 screws (B) to fix both sides of the cabinet.
TOP
Screw (B)
Notes
•
•
•
•
62
Do not block the openings of the cabinet. Allow space of at least 20 cm above and 10 cm at the
sides of the cabinet.
Make sure that the wall behind the cabinet is flat and free of obstacles, so that the openings on the
back of the cabinet will not be blocked.
Make sure that the wall behind the cabinet is not made of wood.
Be careful not to drop the cabinet.
Installation Manual
2.2 Installation of the Hybrid IP-PBX
2.2.12 Wall Mounting (KX-TDA100)
CAUTION
Drive mounting screws into the wall. Be careful to avoid touching any metal laths, wire laths or metal
plates in the wall.
1. Install 3 anchor plugs in the wall, using the metal bracket as a template. Fix the metal bracket with 3
screws (A).
Anchor Plug
Hammer
Anchor Plug
Wall
6.5 mm
Metal Bracket
30 mm
TOP
Screw (A)
TOP
Screw (A)
Metal Bracket
Installation Manual
63
2.2 Installation of the Hybrid IP-PBX
2. Hook the cabinet onto the metal bracket, making sure that the unit slides down and onto the hooked
parts of the metal bracket. Use 2 screws (B) to fix both sides of the cabinet.
TOP
Screw (B)
Notes
•
•
•
•
64
Do not block the openings of the cabinet. Allow space of at least 20 cm above and 10 cm at the
sides of the cabinet.
Make sure that the wall behind the cabinet is flat and free of obstacles, so that the openings on the
back of the cabinet will not be blocked.
Make sure that the wall behind the cabinet is not made of wood.
Be careful not to drop the cabinet.
Installation Manual
2.2 Installation of the Hybrid IP-PBX
2.2.13 Floor Standing (KX-TDA200 Only)
1. Install 4 anchor plugs in the floor, using the metal bracket as a template. Fix the metal bracket with 4
screws (A).
Screw (A)
Metal Bracket
TOP
Screw (A)
Hammer
Anchor
Plug
Metal
Bracket
Anchor Plug
30 mm
Floor
6.5 mm
2. Remove the front cover of the cabinet (refer to "2.2.3 Opening/Closing the Front Cover").
Installation Manual
65
2.2 Installation of the Hybrid IP-PBX
3. Lift the cabinet, attach it to the metal bracket, slide it backwards until it locks, and retain it with 2 screws
(B).
2
1
TOP
FRONT
Screws (B)
Metal Bracket
Notes
•
•
66
Do not block the openings of the cabinet. Allow space of at least 20 cm above and 10 cm at the
sides of the cabinet.
Make sure that the surface behind the cabinet is flat and free of obstacles, so that the openings on
the back of the cabinet will not be blocked.
Installation Manual
2.2 Installation of the Hybrid IP-PBX
•
•
Make sure that the surface behind the cabinet is not made of wood.
Be careful not to drop the cabinet.
4. Fix the front cover on the cabinet (refer to "2.2.3 Opening/Closing the Front Cover").
Installation Manual
67
2.2 Installation of the Hybrid IP-PBX
2.2.14 Surge Protector Installation
Overview
A massive electrical surge can be caused if lightning strikes a telephone cable 10 m above ground, or if a
telephone line comes into contact with a power line. A surge protector is a device that is connected to a trunk
to prevent potentially dangerous electrical surges from entering the building via the trunk and damaging the
Hybrid IP-PBX and connected equipment.
To protect the system from electrical surges, we strongly recommend connecting the system to a surge
protector that meets the following specifications:
– Surge arrestor type: 3-electrode arrestor
– DC spark-over voltage: 230 V
– Maximum peak current: at least 10 kA
Additionally, proper earthing is very important for the protection of the system (refer to "2.2.5 Frame Earth
Connection").
Many countries/areas have regulations requiring surge protection. Be sure to comply with all applicable
laws, regulations, and guidelines.
Installation
Trunk
Trunk
Trunk
Surge
Protector
Terminal
Board
Extn.
Hybrid
IP-PBX
Extn. Extn.
SLT
Earth
68
Installation Manual
PT
CS
Frame
Earth
Extn.: Extension line
2.2 Installation of the Hybrid IP-PBX
Outside Installation
(Main Building)
Surge Protector
Trunk
(Another Building)
Trunk
Extn.
Terminal
Board
Extn.
Surge
Protector
CS
Extn.
Extn.
SLT
Hybrid
IP-PBX
SLT
PT
PT
CS
Earth
Extn.: Extension Line
If you install an extension outside of the building, the following precautions are recommended:
a. Install the extension wire underground.
b. Use a conduit to protect the wire.
Note
The surge protector for an extension and CS is different from that for a trunk.
Installation of an Earth Rod
Surge Protector
Trunk
Earthing
Wire
Hybrid
IP-PBX
(Underground)
Earth Rod
Installation Manual
69
2.2 Installation of the Hybrid IP-PBX
1. Connect the earth rod to the surge protector using an earthing wire with a cross-sectional area of at
least 1.3 mm2.
2. Bury the earth rod near the protector. The earthing wire should be as short as possible.
3. The earthing wire should run straight to the earth rod. Do not run the wire around other objects.
4. Bury the earth rod at least 50 cm underground.
Notes
•
•
70
The above figures are recommendations only.
The length of earth rod and the required depth depend on the composition of the soil.
Installation Manual
2.3 Installation of the Main Processing Card
2.3
Installation of the Main Processing Card
2.3.1
MPR Card
Function
Contains the main processor for all processes, basic shelf main protocol, time switch (TSW) control,
detection of system clock alarm, basic shelf power down alarm, and watchdog timer overflow. An MEC card
and an RMT card can be mounted on the MPR card (refer to "2.3.2 MEC Card" and "2.3.3 RMT Card").
1
2
SD
CARD
LEDs
SD Memory Card
Slot Cover
Reset Button
System Initialise
Switch
SD
Memory
Card 3
SD
CARD
USB
BGM/MOH
Pager
4
SD
CARD
5
Notes
•
•
•
For details about connecting peripherals, refer to "2.11.1 Connection of Peripherals".
For details about System Initialise Switch, refer to "2.13.1 Starting the Hybrid IP-PBX".
For details about Reset Button, refer to "4.1.4 Using the Reset Button".
CAUTION
•
•
•
Use only the SD Memory Card included with the Hybrid IP-PBX, or a Panasonic optional upgrade
SD Memory Card.
The SD Memory Card contains software for all the processes of the Hybrid IP-PBX and all the
customer data. The SD Memory Card must be inserted before start up.
Do not remove the SD Memory Card while power is supplied to the Hybrid IP-PBX. Doing so may
cause the Hybrid IP-PBX to fail to start when you try to restart the system.
Installation Manual
71
2.3 Installation of the Main Processing Card
•
A LITHIUM BATTERY IS USED IN THE MPR CARD. THERE IS A RISK OF EXPLOSION IF
BATTERY IS REPLACED WITH THE INCORRECT TYPE. DISPOSE OF USED BATTERIES
ACCORDING TO THE INSTRUCTIONS.
LED Indications
72
Indication
Colour
Description
BATT ALARM
Red
Battery alarm indication
•
OFF: Normal
ON: Alarm
SD ACCESS
Green
SD memory card status
•
ON: Accessing
Installation Manual
2.3 Installation of the Main Processing Card
2.3.2
MEC Card
Function
Memory expansion card to increase system data storage space, enable Broadcasting and Call Billing for
Guest Room features, and double the number of DPTs, using Digital XDP connection. To be mounted on
the MPR card.
inside
Screw
MEC Card
Accessory and User-supplied Items
Accessory (included): Screws × 2
User-supplied (not included): none
Installation Manual
73
2.3 Installation of the Main Processing Card
2.3.3
RMT Card
Function
Analogue modem card for remote communication with the Hybrid IP-PBX. V90 support. To be mounted on
the MPR card.
inside
Screw
RMT Card
Accessory and User-supplied Items
Accessory (included): Screws × 2
User-supplied (not included): none
74
Installation Manual
2.4 Installation of the Trunk Cards
2.4
Installation of the Trunk Cards
2.4.1
LCOT4, LCOT8, and LCOT16 Cards
Function
LCOT4:
LCOT8:
4-port analogue trunk card with 2 power failure transfer (PFT) ports.
8-port analogue trunk card with 2 power failure transfer (PFT) ports. One CID8 or CID/PAY8
card can be mounted on the LCOT8 card (refer to "2.4.3 CID/PAY8 Card" and "2.4.4 CID8
Card").
LCOT16: 16-port analogue trunk card with 4 power failure transfer (PFT) ports. A maximum of 2 CID8
and CID/PAY8 cards can be mounted on the LCOT16 card (refer to "2.4.3 CID/PAY8 Card" and
"2.4.4 CID8 Card").
LED
Amphenol
To trunk
Accessory and User-supplied Items
Accessory (included): Screws × 2
User-supplied (not included): Amphenol connector
Notes
•
•
•
To connect the Amphenol connector, refer to "2.2.10 Fastening Amphenol Type Connector".
For details about power failure transfer, refer to "2.12.1 Power Failure Connections".
To confirm the trunk connection, refer to "Confirming the Trunk Connection" in "2.13.1 Starting the
Hybrid IP-PBX".
Installation Manual
75
2.4 Installation of the Trunk Cards
Pin Assignments
Amphenol Connector
50
26
Notes
•
•
25
1
No.
Signal Name Function
No.
Signal Name Function
1
RA
Ring port 1
26
TA
Tip port 1
2
RB
Ring port 2
27
TB
Tip port 2
3
RC
Ring port 3
28
TC
Tip port 3
4
RD
Ring port 4
29
TD
Tip port 4
5
RE
Ring port 5
30
TE
Tip port 5
6
RF
Ring port 6
31
TF
Tip port 6
7
RG
Ring port 7
32
TG
Tip port 7
8
RH
Ring port 8
33
TH
Tip port 8
9
RI
Ring port 9
34
TI
Tip port 9
10
RJ
Ring port 10
35
TJ
Tip port 10
11
RK
Ring port 11
36
TK
Tip port 11
12
RL
Ring port 12
37
TL
Tip port 12
13
RM
Ring port 13
38
TM
Tip port 13
14
RN
Ring port 14
39
TN
Tip port 14
15
RO
Ring port 15
40
TO
Tip port 15
16
RP
Ring port 16
41
TP
Tip port 16
17-25
Reserved
–
42-50
Reserved
–
Pin assignments for the pins 5 to 8 and 30 to 33 are for the LCOT8 and LCOT16 card only.
Pin assignments for the pins 9 to 16 and 34 to 41 are for the LCOT16 card only.
LED Indications
76
Indication
Colour
Description
CARD STATUS
Green/Red
Card status indication
•
OFF: Power Off
•
Green ON: Normal (all ports are idle)
•
Green Flashing (60 times per minute): Normal (a port is in use)
•
Red ON: Fault (includes reset)
•
Red Flashing (60 times per minute): Out of Service
Installation Manual
2.4 Installation of the Trunk Cards
2.4.2
DID8 Card
Function
8-port DID trunk card.
LED
Amphenol
To DID line
Accessory and User-supplied Items
Accessory (included): Screws × 2
User-supplied (not included): Amphenol connector
Notes
•
•
To connect the Amphenol connector, refer to "2.2.10 Fastening Amphenol Type Connector".
To confirm the trunk connection, refer to "Confirming the Trunk Connection" in "2.13.1 Starting the
Hybrid IP-PBX".
Pin Assignments
Amphenol Connector
50
26
25
1
No.
Signal Name Function
No.
Signal Name Function
1
RA
Ring port 1
26
TA
Tip port 1
2
RB
Ring port 2
27
TB
Tip port 2
3
RC
Ring port 3
28
TC
Tip port 3
4
RD
Ring port 4
29
TD
Tip port 4
5
RE
Ring port 5
30
TE
Tip port 5
6
RF
Ring port 6
31
TF
Tip port 6
7
RG
Ring port 7
32
TG
Tip port 7
8
RH
Ring port 8
33
TH
Tip port 8
9-25
Reserved
–
34-50
Reserved
–
Installation Manual
77
2.4 Installation of the Trunk Cards
LED Indications
78
Indication
Colour
Description
CARD STATUS
Green/Red
Card status indication
•
OFF: Power Off
•
Green ON: Normal (all ports are idle)
•
Green Flashing (60 times per minute): Normal (a port is in use)
•
Red ON: Fault (includes reset)
•
Red Flashing (60 times per minute): Out of Service
Installation Manual
2.4 Installation of the Trunk Cards
2.4.3
CID/PAY8 Card
Function
8-port Caller ID signal type FSK/FSK (with Call Waiting Caller ID [Visual Caller ID])/DTMF, and 8 ports of
Pay Tone Service (12 kHz/16 kHz). To be mounted on the LCOT8/LCOT16 cards.
Set all DIP switches for ports
09-16 at "OFF" positions
(LCOT16 card only).
inside
OFF
OFF
ON
ON
SW2
SW2
Ports 09-16
CID/PAY8 Card
Screw
Ports 01-08
SW1
SW1
ON
ON
OFF
OFF
Set all DIP switches for
ports 01-08 at "OFF"
positions.
Accessory and User-supplied Items
Accessory (included): Screws × 2
User-supplied (not included): none
Note
Only 1 CID/PAY8 card can be mounted on the LCOT8 card.
Switch Settings (on LCOT8/LCOT16 cards)
Switch
Type
Usage and Status Definition
Port Setting
DIP
Set all DIP switches at "OFF" positions.
Note
SW2 is for the LCOT16 card only.
Installation Manual
79
2.4 Installation of the Trunk Cards
2.4.4
CID8 Card
Function
8-port Caller ID signal type FSK/FSK (with Call Waiting Caller ID [Visual Caller ID])/DTMF. To be mounted
on the LCOT8/LCOT16 cards.
LCOT16 card only
OFF
inside
ON
SW2
CID8 Card
Screw
SW1
ON
OFF
Accessory and User-supplied Items
Accessory (included): Screws × 2
User-supplied (not included): none
Note
Only 1 CID8 card can be mounted on the LCOT8 card.
Switch Settings (on LCOT8/LCOT16 cards)
Switch
Type
Usage and Status Definition
Port Setting
DIP
Keep all DIP switches at default "ON" positions. Do not change the
positions of these switches.
Note
SW2 is for the LCOT16 card only.
80
Installation Manual
2.4 Installation of the Trunk Cards
2.4.5
E&M8 Card
Function
8-port E & M (TIE) trunk card. Type 5 support.
LED
Amphenol
To terminal board from the E & M (TIE) line
Accessory and User-supplied Items
Accessory (included): Screws × 2
User-supplied (not included): Amphenol connector
Notes
•
•
•
Connect this optional service card to the trunk through terminal board from the E & M (TIE) line;
do not connect to the trunk directly.
To connect the Amphenol connector, refer to "2.2.10 Fastening Amphenol Type Connector".
To confirm the trunk connection, refer to "Confirming the Trunk Connection" in "2.13.1 Starting the
Hybrid IP-PBX".
Installation Manual
81
2.4 Installation of the Trunk Cards
Pin Assignments
Amphenol Connector
50
26
82
25
1
No.
Signal Name Function
No.
Signal Name Function
1
TA
Tip port 1
26
RA
Ring port 1
2
T1A
Tip 1 port 1
27
R1A
Ring 1 port 1
3
EA
E line port 1
28
MA
M line port 1
4
SGA
SG line port 1
29
SGB
SG line port 2
5
TB
Tip port 2
30
RB
Ring port 2
6
T1B
Tip 1 port 2
31
R1B
Ring 1 port 2
7
EB
E line port 2
32
MB
M line port 2
8
TC
Tip port 3
33
RC
Ring port 3
9
T1C
Tip 1 port 3
34
R1C
Ring 1 port 3
10
EC
E line port 3
35
MC
M line port 3
11
TD
Tip port 4
36
RD
Ring port 4
12
T1D
Tip 1 port 4
37
R1D
Ring 1 port 4
13
ED
E line port 4
38
MD
M line port 4
14
TE
Tip port 5
39
RE
Ring port 5
15
T1E
Tip 1 port 5
40
R1E
Ring 1 port 5
16
EE
E line port 5
41
ME
M line port 5
17
TF
Tip port 6
42
RF
Ring port 6
18
T1F
Tip 1 port 6
43
R1F
Ring 1 port 6
19
EF
E line port 6
44
MF
M line port 6
20
TG
Tip port 7
45
RG
Ring port 7
21
T1G
Tip 1 port 7
46
R1G
Ring 1 port 7
22
EG
E line port 7
47
MG
M line port 7
23
TH
Tip port 8
48
RH
Ring port 8
24
T1H
Tip 1 port 8
49
R1H
Ring 1 port 8
25
EH
E line port 8
50
MH
M line port 8
Installation Manual
2.4 Installation of the Trunk Cards
LED Indications
Indication
Colour
Description
CARD STATUS
Green/Red
Card status indication
•
OFF: Power Off
•
Green ON: Normal (all ports are idle)
•
Green Flashing (60 times per minute): Normal (a port is in use)
•
Red ON: Fault (includes reset)
•
Red Flashing (60 times per minute): Out of Service
Installation Manual
83
2.4 Installation of the Trunk Cards
2.4.6
T1 Card
Function
1-port T1 trunk card. EIA/TIA standard compliant.
A
LEDs
B
RJ45
To NT1 / Extension
Accessory and User-supplied Items
Accessory (included): Ferrite core × 1
User-supplied (not included): RJ45 connector
Notes
•
•
•
•
When connecting this optional service card to the trunk, connect through NT1; do not connect to
the trunk directly.
When connecting the RJ45 connector, attach the included ferrite core (except in Canada, where
the ferrite core is not necessarily required). Refer to "2.2.9 Attaching a Ferrite Core".
This optional service card can be used for either trunk or extension connection, by setting the A/B
switch or using the connector with appropriate pin assignments.
To confirm the trunk connection, refer to "Confirming the Trunk Connection" in "2.13.1 Starting the
Hybrid IP-PBX".
CAUTION
T1 ports are SELV ports and should only be connected to SELV services.
Switch Settings
84
Switch
Type
Usage and Status Definition
A/B
Slide
Select A (default) for trunk or B for extension use.
Installation Manual
2.4 Installation of the Trunk Cards
Pin Assignments
RJ45 Connector for Trunk Use
8
1
No.
Signal Name
Level [V]
Function
1
RX+
(+)
Receive data (+)
2
RX-
(-)
Receive data (-)
3
Reserved
–
–
4
TX-
(-)
Transmit data (-)
5
TX+
(+)
Transmit data (+)
6-8
Reserved
–
–
RJ45 Connector for Extension Use
8
1
No.
Signal Name
Level [V]
Function
1
TX-
(-)
Transmit data (-)
2
TX+
(+)
Transmit data (+)
3
Reserved
–
–
4
RX+
(+)
Receive data (+)
5
RX-
(-)
Receive data (-)
6-8
Reserved
–
–
LED Indications
Indication
Colour
Description
CARD STATUS
Green/Red
Card status indication
•
OFF: Power Off
•
Green ON: Normal (all ports are idle)
•
Green Flashing (60 times per minute): Normal (a port is in use)
•
Red ON: Fault (includes reset)
•
Red Flashing (60 times per minute): Out of Service
SYNC-ERR
Red
Non-synchronisation status indication
•
OFF: Normal
•
ON: Out of synchronisation
RAI
Red
RAI signal status indication
•
OFF: Normal
•
ON: Alarm (Clock Slave)
•
Flashing (60 times per minute): Alarm (Clock Master)
AIS
Red
AIS status indication
•
OFF: Normal
•
ON: Alarm
Installation Manual
85
2.4 Installation of the Trunk Cards
Indication
Colour
Description
SYNC
Green
Synchronisation status indication
•
OFF: Not synchronised
•
ON: Synchronised
•
Flashing (60 times per minute): Synchronised (Clock Master)
Maximum Cabling Distance of Extension Connection
The maximum distance of the extension cable that connects the T1 cards is shown below:
Diameter
0.5 mm:
86
Installation Manual
Maximum Distance
Under 200 m
2.4 Installation of the Trunk Cards
2.4.7
E1 Card
Function
1-port E1 trunk card. ITU-T standard compliant.
A
LEDs
B
RJ45
BNC (TX) outer conductor
J308
J308
OR
3
1 2
To NT1/Extension
For Frame
Ground Open
To NT1/Extension
For RJ45
For Frame
Ground Short
3
J309
OR
2 1
75Ω
J309
OR
2 1
120Ω
BNC (TX)
BNC (RX)
3
120Ω
For BNC
3
1 2
75Ω
BNC (RX) outer conductor
Accessory and User-supplied Items
Accessory (included): Ferrite core × 1
User-supplied (not included): RJ45 or BNC connector
Notes
•
•
•
•
•
•
In some countries/areas, this optional service card must not be connected to the Public Switched
Telephone Network.
When connecting this optional service card to the trunk, connect through NT1; do not connect to
the trunk directly.
Use only 1 type of connector (RJ45 or BNC) for connection; RJ45 and BNC cannot be used
simultaneously.
When connecting the RJ45 connector, attach the included ferrite core. Refer to "2.2.9 Attaching a
Ferrite Core".
This optional service card can be used for either trunk or extension connection, by setting the A/B
switch or using the connector with appropriate pin assignments.
To confirm the trunk connection, refer to "Confirming the Trunk Connection" in "2.13.1 Starting the
Hybrid IP-PBX".
CAUTION
E1 ports are SELV ports and should only be connected to SELV services.
Installation Manual
87
2.4 Installation of the Trunk Cards
Switch Settings
Switch
Type
Usage and Status Definition
Termination
Slide
Select 120 Ω (default) or 75 Ω for connector type to be used.
A/B
Slide
When using an RJ45 connector, select A (default) for trunk or B for
extension use.
When using BNC connectors, keep the A position.
Frame Ground
Short
Short pin
J308 is for BNC (TX) outer conductor, and J309 is for BNC (RX) outer
conductor.
Connection of 1 and 2: Open (default)
Connection of 2 and 3: Short
Pin Assignments
RJ45 Connector for Trunk Use
8
1
No.
Signal Name
Level [V]
Function
1
RX+
(+)
Receive data (+)
2
RX-
(-)
Receive data (-)
3
Reserved
–
–
4
TX-
(-)
Transmit data (-)
5
TX+
(+)
Transmit data (+)
6-8
Reserved
–
–
RJ45 Connector for Extension use
8
1
No.
Signal Name
Level [V]
Function
1
TX-
(-)
Transmit data (-)
2
TX+
(+)
Transmit data (+)
3
Reserved
–
–
4
RX+
(+)
Receive data (+)
5
RX-
(-)
Receive data (-)
6-8
Reserved
–
–
BNC (coaxial) Connector (TX)
88
No.
Signal Name
Level [V]
Function
1
1
TX+
(+)
Transmit data (+)
2
2
TX-
(-)
Transmit data (-)
Installation Manual
2.4 Installation of the Trunk Cards
BNC (coaxial) Connector (RX)
No.
Signal Name
Level [V]
Function
1
1
RX-
(-)
Receive data (-)
2
2
RX+
(+)
Receive data (+)
LED Indications
Indication
Colour
Description
CARD STATUS
Green/Red
Card status indication
•
OFF: Power Off
•
Green ON: Normal (all ports are idle)
•
Green Flashing (60 times per minute): Normal (a port is in use)
•
Red ON: Fault (includes reset)
•
Red Flashing (60 times per minute): Out of Service
SYNC-ERR
Red
Non-synchronisation status indication
•
OFF: Normal
•
ON: Out of synchronisation
RAI
Red
RAI signal status indication
•
OFF: Normal
•
ON: Alarm (Clock Slave)
•
Flashing (60 times per minute): Alarm (Clock Master)
AIS
Red
AIS status indication
•
OFF: Normal
•
ON: Alarm
SYNC
Green
Synchronisation status indication
•
OFF: Not synchronised
•
ON: Synchronised
•
Flashing (60 times per minute): Synchronised (Clock Master)
Maximum Cabling Distance of Extension Connection
The maximum distance of the extension cable that connects the E1 cards is shown below:
Diameter
0.5 mm:
Maximum Distance
Under 200 m
Installation Manual
89
2.4 Installation of the Trunk Cards
2.4.8
BRI4 and BRI8 Cards
Function
BRI4: 4-port ISDN Basic Rate Interface card with 1 power failure transfer port. EURO-ISDN/
ETSI compliant.
BRI8: 8-port ISDN Basic Rate Interface card with 1 power failure transfer port. EURO-ISDN/
ETSI compliant.
LEDs
B
A
RJ45
(LINE 1 to LINE 8)
To NT1/ Extension
Accessory and User-supplied Items
Accessory (included): Ferrite core(s) × 1 (BRI4 card) or 2 (BRI8 card)
User-supplied (not included): RJ45 connector
Notes
•
•
•
•
•
•
•
LINE 5 to LINE 8 are for BRI8 card only.
When connecting these optional service cards to the trunk, connect through an NT1; do not
connect to the U interface of the trunk directly.
These optional service cards have 100
of terminal resistance. For use in point to multi-point
connection, the cards must be placed at the end of the bus.
When connecting the RJ45 connector, attach the included ferrite core. Refer to "2.2.9 Attaching a
Ferrite Core".
These optional service cards can be used for either trunk or extension connection, by setting the
A/B switch or using the connector with appropriate pin assignments.
For details about power failure transfer, refer to "2.12.1 Power Failure Connections".
To confirm the trunk connection, refer to "Confirming the Trunk Connection" in "2.13.1 Starting the
Hybrid IP-PBX".
Notice
If the connected ISDN terminal has no external power source, make sure that the power is supplied
from the BRI4/BRI8 card by programming the Hybrid IP-PBX accordingly.
However, if there is an external power source to the terminal, make sure that there is no power supplied
to the terminal from the BRI4/BRI8 card. Failure to do so may cause damage to the power supply circuit
of the BRI4/BRI8 card or the terminal.
90
Installation Manual
2.4 Installation of the Trunk Cards
Switch Settings
Switch
Type
Usage and Status Definition
A/B
Slide
Select A (default) for trunk or B for extension use.
Pin Assignments
RJ45 Connector for Trunk Use
8
1
No.
Signal Name
Level [V]
Function
1-2
Reserved
–
–
3
TX1
(+)
Transmit data 1
4
RX2
(+)
Receive data 2
5
RX1
(-)
Receive data 1
6
TX2
(-)
Transmit data 2
7-8
Reserved
–
–
RJ45 Connector for Extension Use
8
1
No.
Signal Name
Level [V]
Function
1-2
Reserved
–
–
3
RX2
(+)
Receive data 2
4
TX1
(+)
Transmit data 1
5
TX2
(-)
Transmit data 2
6
RX1
(-)
Receive data 1
7-8
Reserved
–
–
LED Indications
Indication
Colour
Description
CARD STATUS
Green/Red
Card status indication
•
OFF: Power Off
•
Green ON: Normal (all ports are idle)
•
Green Flashing (60 times per minute): Normal (a port is in use)
•
Red ON: Fault (includes reset)
•
Red Flashing (60 times per minute): Out of Service
Installation Manual
91
2.4 Installation of the Trunk Cards
Indication
Colour
Description
LINE 8
LINE 7
LINE 6
LINE 5
LINE 4
LINE 3
LINE 2
LINE 1
Green
Line status indication (LINE 1 to LINE 8):
Refer to "LINE LED Pattern" below for details.
Note
LINE 5 to LINE 8 are for BRI8 card only.
LINE LED Pattern
Layer 1
Layer 2
Master Clock
LED Pattern
OFF
OFF
OFF
1s
ON
OFF
OFF
1s
ON
ON
OFF
1s
ON
OFF
ON
1s
ON
ON
ON
1s
Layer 1: ON (Synchronous)
Layer 2: ON (Link established)/OFF (Link not established)
Master Clock: ON (Master)/OFF (Slave)
92
Installation Manual
2.4 Installation of the Trunk Cards
Maximum Cabling Distance of S0 Bus Connection
The maximum distance of the extension cable that connects the Hybrid IP-PBX and the ISDN terminal
equipment (TE) is shown below:
CAT 5: Under 1000 m
Point-to-Point
TE
CAT 5: Under 150 m
TE 1
CAT 5: Under 500 m
TE 1
Point-to-Multipoint
TE 8
CAT 5: Under 50 m
Expansion
Point-to-Multipoint
TE 8
Installation Manual
93
2.4 Installation of the Trunk Cards
2.4.9
PRI30 Card
Function
1-port ISDN Primary Rate Interface card (30B channels). EURO-ISDN/ETSI compliant.
A
LEDs
B
RJ45
To NT1 / Extension
To NT1/Extension
For RJ45
120Ω
120Ω
BNC (TX)
BNC (RX)
OR
For BNC
75Ω
75Ω
Accessory and User-supplied Items
Accessory (included): Ferrite core × 1
User-supplied (not included): RJ45 or BNC connector
Notes
•
•
•
•
•
•
In some countries/areas, this optional service card must not be connected to the Public Switched
Telephone Network.
When connecting this optional service card to the trunk, connect through an NT1; do not connect
to the U interface of the trunk directly.
Use only 1 type of connector (RJ45 or BNC) for connection; RJ45 and BNC cannot be used
simultaneously.
When connecting the RJ45 connector, attach the included ferrite core. Refer to "2.2.9 Attaching a
Ferrite Core".
This optional service card can be used for either trunk or extension connection, by setting the A/B
switch or using the connector with appropriate pin assignments.
To confirm the trunk connection, refer to "Confirming the Trunk Connection" in "2.13.1 Starting the
Hybrid IP-PBX".
CAUTION
PRI ports are SELV ports and should only be connected to SELV services.
94
Installation Manual
2.4 Installation of the Trunk Cards
Switch Settings
Switch
Type
Usage and Status Definition
Termination
Slide
Select 120 Ω (default) or 75 Ω for connector type to be used.
A/B
Slide
When using an RJ45 connector, select A (default) for trunk or B for
extension use.
When using BNC connectors, keep the A position.
Pin Assignments
RJ45 Connector for Trunk Use
8
1
No.
Signal Name
Level [V]
Function
1
RX+
(+)
Receive data (+)
2
RX-
(-)
Receive data (-)
3
Reserved
–
–
4
TX-
(-)
Transmit data (-)
5
TX+
(+)
Transmit data (+)
6-8
Reserved
–
–
RJ45 Connector for Extension Use
8
1
No.
Signal Name
Level [V]
Function
1
TX-
(-)
Transmit data (-)
2
TX+
(+)
Transmit data (+)
3
Reserved
–
–
4
RX+
(+)
Receive data (+)
5
RX-
(-)
Receive data (-)
6-8
Reserved
–
–
BNC (coaxial) Connector (TX)
No.
Signal Name
Level [V]
Function
1
1
TX+
(+)
Transmit data (+)
2
2
TX-
(-)
Transmit data (-)
Installation Manual
95
2.4 Installation of the Trunk Cards
BNC (coaxial) Connector (RX)
No.
Signal Name
Level [V]
Function
1
1
RX-
(-)
Receive data (-)
2
2
RX+
(+)
Receive data (+)
LED Indications
96
Indication
Colour
Description
CARD STATUS
Green/Red
Card status indication
•
OFF: Power Off
•
Green ON: Normal (all ports are idle)
•
Green Flashing (60 times per minute): Normal (a port is in use)
•
Red ON: Fault (includes reset)
•
Red Flashing (60 times per minute): Out of Service
SYNC-ERR
Red
Non-synchronisation status indication
•
OFF: Normal
•
ON: Out of synchronisation
RAI
Red
RAI signal status indication
•
OFF: Normal
•
ON: Alarm (Clock Slave)
•
Flashing (60 times per minute): Alarm (Clock Master)
AIS
Red
AIS status indication
•
OFF: Normal
•
ON: Alarm
SYNC
Green
Synchronisation status indication
•
OFF: Not synchronised
•
ON: Synchronised
•
Flashing (60 times per minute): Synchronised (Clock Master)
D-LINK
Green
Data link status indication
•
OFF: Not established
•
ON: Established
Installation Manual
2.4 Installation of the Trunk Cards
Maximum Cabling Distance of Extension Connection
The maximum distance of the extension cable that connects the PRI30 cards is shown below:
Diameter
0.5 mm:
Maximum Distance
Under 200 m
Installation Manual
97
2.4 Installation of the Trunk Cards
2.4.10 PRI23 Card
Function
1-port ISDN Primary Rate Interface card (23B channels). NI (North American standard ISDN protocol)
compliant.
A
LEDs
B
RJ45
To NT1/ Extension
Accessory and User-supplied Items
Accessory (included): Ferrite core × 1
User-supplied (not included): RJ45 connector
Notes
•
•
•
•
When connecting this optional service card to the trunk, connect through an NT1; do not connect
to the U interface of the trunk directly.
When connecting the RJ45 connector, attach the included ferrite core (except in Canada, where
the ferrite core is not necessarily required). Refer to "2.2.9 Attaching a Ferrite Core".
This optional service card can be used for either trunk or extension connection, by setting the A/B
switch or using the connector with appropriate pin assignments.
To confirm the trunk connection, refer to "Confirming the Trunk Connection" in "2.13.1 Starting the
Hybrid IP-PBX".
CAUTION
PRI ports are SELV ports and should only be connected to SELV services.
Switch Settings
98
Switch
Type
Usage and Status Definition
A/B
Slide
Select A (default) for trunk or B for extension use.
Installation Manual
2.4 Installation of the Trunk Cards
Pin Assignments
RJ45 Connector for Trunk Use
8
1
No.
Signal Name
Level [V]
Function
1
RX+
(+)
Receive data (+)
2
RX-
(-)
Receive data (-)
3
Reserved
–
–
4
TX-
(-)
Transmit data (-)
5
TX+
(+)
Transmit data (+)
6-8
Reserved
–
–
RJ45 Connector for Extension Use
8
1
No.
Signal Name
Level [V]
Function
1
TX-
(-)
Transmit data (-)
2
TX+
(+)
Transmit data (+)
3
Reserved
–
–
4
RX+
(+)
Receive data (+)
5
RX-
(-)
Receive data (-)
6-8
Reserved
–
–
LED Indications
Indication
Colour
Description
CARD STATUS
Green/Red
Card status indication
•
OFF: Power Off
•
Green ON: Normal (all ports are idle)
•
Green Flashing (60 times per minute): Normal (a port is in use)
•
Red ON: Fault (includes reset)
•
Red Flashing (60 times per minute): Out of Service
SYNC-ERR
Red
Non-synchronisation status indication
•
OFF: Normal
•
ON: Out of synchronisation
RAI
Red
RAI signal status indication
•
OFF: Normal
•
ON: Alarm (Clock Slave)
•
Flashing (60 times per minute): Alarm (Clock Master)
AIS
Red
AIS status indication
•
OFF: Normal
•
ON: Alarm
Installation Manual
99
2.4 Installation of the Trunk Cards
Indication
Colour
Description
SYNC
Green
Synchronisation status indication
•
OFF: Not synchronised
•
ON: Synchronised
•
Flashing (60 times per minute): Synchronised (Clock Master)
D-LINK
Green
Data link status indication
•
OFF: Not established
•
ON: Established
Maximum Cabling Distance of Extension Connection
The maximum distance of the extension cable that connects the PRI23 cards is shown below:
Diameter
0.5 mm:
100
Installation Manual
Maximum Distance
Under 200 m
2.4 Installation of the Trunk Cards
2.4.11 IP-GW4 Card
Function
4-channel VoIP gateway card. Compliant with VoIP H.323 V.2 protocol, and ITU-T G.729a and G.723.1
CODEC methods. G3 fax support.
LEDs
RJ45 (10BASE-T)
To private IP network
Accessory and User-supplied Items
Accessory (included): CD-ROM (including PC programming software and documentation) × 1
User-supplied (not included): RJ45 connector
Notes
•
•
•
•
Maximum length of the cable to be connected to this optional service card is 100 m.
The IP-GW4 card occupies the space of 2 free slots when it is installed in the Hybrid IP-PBX.
For programming instructions and other information about the IP-GW4 card, refer to the
documentation for the IP-GW4 card. To programme the IP-GW4 card, use the PC programming
software designed for the IP-GW4 card.
To confirm the trunk connection, refer to "Confirming the Trunk Connection" in "2.13.1 Starting the
Hybrid IP-PBX".
Pin Assignments
RJ45 Connector (10BASE-T)
8
1
No.
Signal Name
Input (I)/Output (O)
Function
1
TPO+
O
Transmit data+
2
TPO-
O
Transmit data-
3
TPI+
I
Receive data+
4-5
Reserved
–
–
6
TPI-
I
Receive data-
7-8
Reserved
–
–
Installation Manual
101
2.4 Installation of the Trunk Cards
LED Indications
102
Indication
Colour
Description
CARD STATUS
Green/Red
Card status indication
•
OFF: Power Off
•
Green ON: Normal (all ports are idle)
•
Green Flashing (60 times per minute): Normal (a port is in use)
•
Red ON: Fault (includes reset)
•
Red Flashing (60 times per minute): Out of Service
ONLINE
Green
On-line status indication
•
ON: On-line mode
•
Flashing: Emergency maintenance mode
ALARM
Red
Alarm indication
•
OFF: Normal
•
ON: Alarm
IAM BUSY
Green
Busy status indication
•
OFF: Not used
•
ON: At least one line is used
LINK
Green
Link status indication
•
OFF: Connection error
•
ON: Normal connection
DATA
Green
Data transmission indication
•
OFF: No data transmitted
•
ON: Data transmitting
COL
Green
Data collision indication
•
OFF: No data collision
•
ON: Data collision
SIOSEL
Green
Serial maintenance port status indication
•
OFF: CPU power port used (maintenance port not available)
•
ON: Maintenance port available
Installation Manual
2.4 Installation of the Trunk Cards
2.4.12 IP-GW4E Card
Function
4-channel VoIP gateway card. Compliant with VoIP H.323 V.2 protocol, and ITU-T G.729a, G.723.1, and
G.711 CODEC methods.
LEDs
RJ45
(10BASE-T/100BASE-TX)
To private IP network
Accessory and User-supplied Items
Accessory (included): CD-ROM (including documentation for web programming) × 1
User-supplied (not included): RJ45 connector
Notes
•
•
•
•
Maximum length of the cable to be connected to this optional service card is 100 m.
The IP-GW4E card occupies the space of only 1 free slot when it is installed in the Hybrid IP-PBX.
For programming instructions and other information about the IP-GW4E card, refer to the
documentation for the IP-GW4E card. To programme the IP-GW4E card, use the web
programming designed for the IP-GW4E card.
To confirm the trunk connection, refer to "Confirming the Trunk Connection" in "2.13.1 Starting the
Hybrid IP-PBX".
Pin Assignments
RJ45 Connector (10BASE-T/100BASE-TX)
8
1
No.
Signal Name
Input (I)/Output (O)
Function
1
TPO+
O
Transmit data+
2
TPO-
O
Transmit data-
3
TPI+
I
Receive data+
4-5
Reserved
–
–
6
TPI-
I
Receive data-
7-8
Reserved
–
–
Installation Manual
103
2.4 Installation of the Trunk Cards
LED Indications
Indication
Colour
Description
CARD STATUS
Green/Red
Card status indication
•
OFF: Power Off
•
Green ON: Normal (all ports are idle)
•
Green Flashing (60 times per minute): Normal (a port is in use)
•
Red ON: Fault (includes reset)
•
Red Flashing (60 times per minute): Out of Service
ONLINE
Green
On-line status indication
•
ON: On-line mode
•
OFF: Off-line mode
•
Flashing: Maintenance mode
Note
If the LINK indicator is OFF, the ONLINE indicator will also be
OFF.
104
ALARM
Red
Alarm indication
•
OFF: Normal
•
ON: Alarm
VoIP BUSY
Green
VoIP (H.323) process indication
•
OFF: VoIP process inactive
•
ON: VoIP process active
LINK
Green
Link status indication
•
OFF: Connection error
•
ON: Normal connection
DATA
Green
Data transmission indication
•
OFF: No data transmitted
•
ON: Data transmitting
Installation Manual
2.4 Installation of the Trunk Cards
2.4.13 IP-GW16 Card
Function
16-channel VoIP gateway card. Compliant with VoIP H.323 V.2 protocol, and ITU-T G.729a, G.723.1, and
G.711 CODEC methods.
LEDs
RJ45
(10BASE-T/100BASE-TX
Full Duplex)
To private IP network
Accessory and User-supplied Items
Accessory (included): Ferrite core × 1, CD-ROM (including documentation for web programming) × 1
User-supplied (not included): RJ45 connector
Notes
•
•
•
•
Maximum length of the cable to be connected to this optional service card is 100 m.
When connecting the RJ45 connector, attach the included ferrite core. Refer to "2.2.9 Attaching a
Ferrite Core".
For programming instructions and other information about the IP-GW16 card, refer to the
documentation for the IP-GW16 card. To programme the IP-GW16 card, use the web programming
designed for the IP-GW16 card.
To confirm the trunk connection, refer to "Confirming the Trunk Connection" in "2.13.1 Starting the
Hybrid IP-PBX".
Pin Assignments
RJ45 Connector (10BASE-T/100BASE-TX)
8
1
No.
Signal Name
Input (I)/Output (O)
Function
1
TPO+
O
Transmit data+
2
TPO-
O
Transmit data-
3
TPI+
I
Receive data+
4-5
Reserved
–
–
6
TPI-
I
Receive data-
7-8
Reserved
–
–
Installation Manual
105
2.4 Installation of the Trunk Cards
LED Indications
Indication
Colour
Description
CARD STATUS
Green/Red
Card status indication
•
OFF: Power Off
•
Green ON: Normal (all ports are idle)
•
Green Flashing (60 times per minute): Normal (a port is in use)
•
Red ON: Fault (includes reset)
•
Red Flashing (60 times per minute): Out of Service
ONLINE
Green
On-line status indication
•
ON: On-line mode
•
OFF: Off-line mode
•
Flashing: Maintenance mode
Note
If the LINK indicator is OFF, the ONLINE indicator will also be
OFF.
106
ALARM
Red
Alarm indication
•
OFF: Normal
•
ON: Alarm
VoIP BUSY
Green
VoIP (H.323) process indication
•
OFF: VoIP process inactive
•
ON: VoIP process active
LINK
Green
Link status indication
•
OFF: Connection error
•
ON: Normal connection
DATA
Green
Data transmission indication
•
OFF: No data transmitted
•
ON: Data transmitting
Installation Manual
2.5 Installation of the Extension Cards
2.5
Installation of the Extension Cards
2.5.1
CSIF4 and CSIF8 Card
Function
CSIF4: 4-port CS interface card for 4 CSs.
CSIF8: 8-port CS interface card for 8 CSs.
LED
RJ45
(LINE 1 to LINE 8)
To CS
Accessory and User-supplied Items
Accessory (included): none
User-supplied (not included): RJ45 connector
Notes
•
•
•
LINE 5 to LINE 8 are for CSIF8 card only.
When using the CSIF4 card, please note that the Hybrid IP-PBX software will recognise the CSIF4
card as the CSIF8 card. As a result, 8 cell stations may appear to be available; however, only 4 cell
stations are supported by the CSIF4 card.
For details about connecting the CS, refer to "2.8.7 Connecting a Cell Station to the Hybrid IP-PBX"
in "2.8 Connection of DECT Portable Stations" or "2.9.7 Connecting a Cell Station to the Hybrid IPPBX" in "2.9 Connection of 2.4 GHz Portable Stations".
Installation Manual
107
2.5 Installation of the Extension Cards
Pin Assignments
RJ45 Connector
8
1
No.
Signal Name
Function
1-2
Reserved
–
3
D1
Data port (High)
4
POWH
Power (High)
5
POWL
Power (Low)
6
D2
Data port (Low)
7-8
Reserved
–
LED Indications
108
Indication
Colour
Description
CARD STATUS
Green/Red
Card status indication
•
OFF: Power Off
•
Green ON: Normal (all ports are idle)
•
Green Flashing (60 times per minute): Normal (a port is in use)
•
Red ON: Fault (includes reset)
•
Red Flashing (60 times per minute): Out of Service
Installation Manual
2.5 Installation of the Extension Cards
2.5.2
DHLC8 Card
Function
8-port digital hybrid extension card for DPTs, APTs, SLTs, DSS consoles, and PT-interface CSs, with 2
power failure transfer (PFT) ports.
LED
Amphenol
To extensions
Accessory and User-supplied Items
Accessory (included): Screws × 2, Ferrite core × 1
User-supplied (not included): Amphenol connector
Notes
•
•
•
Attach the included ferrite core to the cable. Refer to "2.2.9 Attaching a Ferrite Core".
To connect the Amphenol connector, refer to "2.2.10 Fastening Amphenol Type Connector".
For details about power failure transfer, refer to "2.12.1 Power Failure Connections".
Installation Manual
109
2.5 Installation of the Extension Cards
Pin Assignments
Amphenol Connector
50
26
25
1
No. Signal Name Function
No. Signal Name Function
1
RA
SLT Ring port 1
26
TA
SLT Tip port 1
2
D2A
PT Data port 1 (Low)
27
D1A
PT Data port 1 (High)
3
Reserved
–
28
Reserved
–
4
RB
SLT Ring port 2
29
TB
SLT Tip port 2
5
D2B
PT Data port 2 (Low)
30
D1B
PT Data port 2 (High)
6
Reserved
–
31
Reserved
–
7
RC
SLT Ring port 3
32
TC
SLT Tip port 3
8
D2C
PT Data port 3 (Low)
33
D1C
PT Data port 3 (High)
9
Reserved
–
34
Reserved
–
10
RD
SLT Ring port 4
35
TD
SLT Tip port 4
11
D2D
PT Data port 4 (Low)
36
D1D
PT Data port 4 (High)
12
Reserved
–
37
Reserved
–
13
RE
SLT Ring port 5
38
TE
SLT Tip port 5
14
D2E
PT Data port 5 (Low)
39
D1E
PT Data port 5 (High)
15
Reserved
–
40
Reserved
–
16
RF
SLT Ring port 6
41
TF
SLT Tip port 6
17
D2F
PT Data port 6 (Low)
42
D1F
PT Data port 6 (High)
18
Reserved
–
43
Reserved
–
19
RG
SLT Ring port 7
44
TG
SLT Tip port 7
20
D2G
PT Data port 7 (Low)
45
D1G
PT Data port 7 (High)
21
Reserved
–
46
Reserved
–
22
RH
SLT Ring port 8
47
TH
SLT Tip port 8
23
D2H
PT Data port 8 (Low)
48
D1H
PT Data port 8 (High)
–
49- Reserved
50
24- Reserved
25
110
Installation Manual
–
2.5 Installation of the Extension Cards
LED Indications
Indication
Colour
Description
CARD STATUS
Green/
Orange/Red
Card status indication
•
OFF: Power Off
•
Green ON: Normal (all ports are idle)
•
Green Flashing (60 times per minute): Normal (a port is in use)
•
Orange Flashing: Detection of PT-interface CS connection (when
starting up the PT-interface CS)
•
Red ON: Fault (includes reset)
•
Red Flashing (60 times per minute): Out of Service
Installation Manual
111
2.5 Installation of the Extension Cards
2.5.3
DLC8 Card
Function
8-port digital extension card for DPTs, DSS consoles, and PT-interface CSs.
LED
Amphenol
To extensions
Accessory and User-supplied Items
Accessory (included): Screws × 2, Ferrite core × 1
User-supplied (not included): Amphenol connector
Notes
•
•
112
Attach the included ferrite core to the cable. Refer to "2.2.9 Attaching a Ferrite Core".
To connect the Amphenol connector, refer to "2.2.10 Fastening Amphenol Type Connector".
Installation Manual
2.5 Installation of the Extension Cards
Pin Assignments
Amphenol Connector
50
26
25
1
No.
Signal Name Function
No.
Signal Name Function
1
Reserved
–
26
Reserved
–
2
D2A
Data port 1 (Low)
27
D1A
Data port 1 (High)
3-4
Reserved
–
28-29
Reserved
–
5
D2B
Data port 2 (Low)
30
D1B
Data port 2 (High)
6-7
Reserved
–
31-32
Reserved
–
8
D2C
Data port 3 (Low)
33
D1C
Data port 3 (High)
9-10
Reserved
–
34-35
Reserved
–
11
D2D
Data port 4 (Low)
36
D1D
Data port 4 (High)
12-13
Reserved
–
37-38
Reserved
–
14
D2E
Data port 5 (Low)
39
D1E
Data port 5 (High)
15-16
Reserved
–
40-41
Reserved
–
17
D2F
Data port 6 (Low)
42
D1F
Data port 6 (High)
18-19
Reserved
–
43-44
Reserved
–
20
D2G
Data port 7 (Low)
45
D1G
Data port 7 (High)
21-22
Reserved
–
46-47
Reserved
–
23
D2H
Data port 8 (Low)
48
D1H
Data port 8 (High)
24-25
Reserved
–
49-50
Reserved
–
LED Indications
Indication
Colour
Description
CARD STATUS
Green/
Orange/Red
Card status indication
•
OFF: Power Off
•
Green ON: Normal (all ports are idle)
•
Green Flashing (60 times per minute): Normal (a port is in use)
•
Orange Flashing: Detection of PT-interface CS connection (when
starting up the PT-interface CS)
•
Red ON: Fault (includes reset)
•
Red Flashing (60 times per minute): Out of Service
Installation Manual
113
2.5 Installation of the Extension Cards
2.5.4
DLC16 Card
Function
16-port digital extension card for DPTs, DSS consoles, and PT-interface CSs.
LED
Amphenol
To extensions
Accessory and User-supplied Items
Accessory (included): Screws × 2, Ferrite core × 1
User-supplied (not included): Amphenol connector
Notes
•
•
114
Attach the included ferrite core to the cable. Refer to "2.2.9 Attaching a Ferrite Core".
To connect the Amphenol connector, refer to "2.2.10 Fastening Amphenol Type Connector".
Installation Manual
2.5 Installation of the Extension Cards
Pin Assignments
Amphenol Connector
50
26
25
1
No.
Signal Name Function
No.
Signal Name Function
1
D2A
Data port 1 (Low)
26
D1A
Data port 1 (High)
2
D2B
Data port 2 (Low)
27
D1B
Data port 2 (High)
3
D2C
Data port 3 (Low)
28
D1C
Data port 3 (High)
4
D2D
Data port 4 (Low)
29
D1D
Data port 4 (High)
5
D2E
Data port 5 (Low)
30
D1E
Data port 5 (High)
6
D2F
Data port 6 (Low)
31
D1F
Data port 6 (High)
7
D2G
Data port 7 (Low)
32
D1G
Data port 7 (High)
8
D2H
Data port 8 (Low)
33
D1H
Data port 8 (High)
9
D2I
Data port 9 (Low)
34
D1I
Data port 9 (High)
10
D2J
Data port 10 (Low)
35
D1J
Data port 10 (High)
11
D2K
Data port 11 (Low)
36
D1K
Data port 11 (High)
12
D2L
Data port 12 (Low)
37
D1L
Data port 12 (High)
13
D2M
Data port 13 (Low)
38
D1M
Data port 13 (High)
14
D2N
Data port 14 (Low)
39
D1N
Data port 14 (High)
15
D2O
Data port 15 (Low)
40
D1O
Data port 15 (High)
16
D2P
Data port 16 (Low)
41
D1P
Data port 16 (High)
17-25
Reserved
–
42-50
Reserved
–
LED Indications
Indication
Colour
Description
CARD STATUS
Green/
Orange/Red
Card status indication
•
OFF: Power Off
•
Green ON: Normal (all ports are idle)
•
Green Flashing (60 times per minute): Normal (a port is in use)
•
Orange Flashing: Detection of PT-interface CS connection (when
starting up the PT-interface CS)
•
Red ON: Fault (includes reset)
•
Red Flashing (60 times per minute): Out of Service
Installation Manual
115
2.5 Installation of the Extension Cards
2.5.5
SLC8 Card
Function
8-port extension card for SLTs with 2 power failure transfer (PFT) ports.
LED
Amphenol
To extensions
Accessory and User-supplied Items
Accessory (included): Screws × 2, Ferrite core × 1
User-supplied (not included): Amphenol connector
Notes
•
•
•
116
Attach the included ferrite core to the cable. Refer to "2.2.9 Attaching a Ferrite Core".
To connect the Amphenol connector, refer to "2.2.10 Fastening Amphenol Type Connector".
For details about power failure transfer, refer to "2.12.1 Power Failure Connections".
Installation Manual
2.5 Installation of the Extension Cards
Pin Assignments
Amphenol Connector
50
26
25
1
No.
Signal Name Function
No.
Signal Name Function
1
RA
Ring port 1
26
TA
Tip port 1
2-3
Reserved
–
27-28
Reserved
–
4
RB
Ring port 2
29
TB
Tip port 2
5-6
Reserved
–
30-31
Reserved
–
7
RC
Ring port 3
32
TC
Tip port 3
8-9
Reserved
–
33-34
Reserved
–
10
RD
Ring port 4
35
TD
Tip port 4
11-12
Reserved
–
36-37
Reserved
–
13
RE
Ring port 5
38
TE
Tip port 5
14-15
Reserved
–
39-40
Reserved
–
16
RF
Ring port 6
41
TF
Tip port 6
17-18
Reserved
–
43-44
Reserved
–
19
RG
Ring port 7
44
TG
Tip port 7
20-21
Reserved
–
45-46
Reserved
–
22
RH
Ring port 8
47
TH
Tip port 8
23-25
Reserved
–
48-50
Reserved
–
LED Indications
Indication
Colour
Description
CARD STATUS
Green/Red
Card status indication
•
OFF: Power Off
•
Green ON: Normal (all ports are idle)
•
Green Flashing (60 times per minute): Normal (a port is in use)
•
Red ON: Fault (includes reset)
•
Red Flashing (60 times per minute): Out of Service
Installation Manual
117
2.5 Installation of the Extension Cards
2.5.6
EXT-CID Card
Function
Sends Caller ID signals to extension ports. To be mounted on the SLC8 card.
inside
SLC8 Card
Screw
EXT-CID Card
Accessory and User-supplied Items
Accessory (included): Screws × 2
User-supplied (not included): none
118
Installation Manual
2.5 Installation of the Extension Cards
2.5.7
SLC16 and MSLC16 Cards
Function
SLC16:
16-port extension card for SLTs with 4 power failure transfer (PFT) ports.
MSLC16: 16-port extension card for SLTs with Message Waiting Lamp control and 4 power
failure transfer (PFT) ports. Maximum power output of 160 V/90 V for Message
Waiting Lamp control.
LED
Amphenol
To extensions
Accessory and User-supplied Items
Accessory (included): Screws × 2, Ferrite core × 1
User-supplied (not included): Amphenol connector
Notes
•
•
•
•
Panasonic SLT with Message Waiting Lamp (e.g., KX-T7310) is recommended for connection to
the MSLC16 card.
Attach the included ferrite core to the cable. Refer to "2.2.9 Attaching a Ferrite Core".
To connect the Amphenol connector, refer to "2.2.10 Fastening Amphenol Type Connector".
For details about power failure transfer, refer to "2.12.1 Power Failure Connections".
Installation Manual
119
2.5 Installation of the Extension Cards
Pin Assignments
Amphenol Connector
50
26
25
1
No.
Signal Name Function
No.
Signal Name Function
1
RA
Ring port 1
26
TA
Tip port 1
2
RB
Ring port 2
27
TB
Tip port 2
3
RC
Ring port 3
28
TC
Tip port 3
4
RD
Ring port 4
29
TD
Tip port 4
5
RE
Ring port 5
30
TE
Tip port 5
6
RF
Ring port 6
31
TF
Tip port 6
7
RG
Ring port 7
32
TG
Tip port 7
8
RH
Ring port 8
33
TH
Tip port 8
9
RI
Ring port 9
34
TI
Tip port 9
10
RJ
Ring port 10
35
TJ
Tip port 10
11
RK
Ring port 11
36
TK
Tip port 11
12
RL
Ring port 12
37
TL
Tip port 12
13
RM
Ring port 13
38
TM
Tip port 13
14
RN
Ring port 14
39
TN
Tip port 14
15
RO
Ring port 15
40
TO
Tip port 15
16
RP
Ring port 16
41
TP
Tip port 16
17-25
Reserved
–
42-50
Reserved
–
LED Indications
120
Indication
Colour
Description
CARD STATUS
Green/Red
Card status indication
•
OFF: Power Off
•
Green ON: Normal (all ports are idle)
•
Green Flashing (60 times per minute): Normal (a port is in use)
•
Red ON: Fault (includes reset)
•
Red Flashing (60 times per minute): Out of Service
Installation Manual
2.5 Installation of the Extension Cards
2.5.8
IP-EXT16 Card
Function
16-channel VoIP extension card. Compliant with Panasonic proprietary protocol, and ITU-T G.729a and
G.711 CODEC methods.
LEDs
RJ45
(100BASE-TX
Full Duplex)
To private IP network
Accessory and User-supplied Items
Accessory (included): Ferrite core × 1
User-supplied (not included): RJ45 connector
Notes
•
•
Maximum length of the cable to be connected to this optional service card is 100 m.
When connecting the RJ45 connector, attach the included ferrite core. Refer to "2.2.9 Attaching a
Ferrite Core".
Pin Assignments
RJ45 Connector (10BASE-T/100BASE-TX)
8
1
No.
Signal Name
Input (I)/Output (O)
Function
1
TPO+
O
Transmit data+
2
TPO-
O
Transmit data-
3
TPI+
I
Receive data+
4-5
Reserved
–
–
6
TPI-
I
Receive data-
7-8
Reserved
–
–
Installation Manual
121
2.5 Installation of the Extension Cards
LED Indications
Indication
Colour
Description
CARD STATUS
Green/Red
Card status indication
•
OFF: Power Off
•
Green ON: Normal (all ports are idle)
•
Green Flashing (60 times per minute): Normal (a port is in use)
•
Red ON: Fault (includes reset)
•
Red Flashing (60 times per minute): Out of Service
ONLINE
Green
On-line status indication
•
ON: At least one port is in use (an IP-PT is connected)
•
OFF: No ports are in use (No IP-PTs are connected)
Note
If the LINK indicator is OFF, the ONLINE indicator will also be
OFF.
122
ALARM
Red
Alarm indication
•
OFF: Normal
•
ON: Alarm
VoIP BUSY
Green
Panasonic proprietary VoIP protocol process indication
•
OFF: VoIP process inactive
•
ON: VoIP process active
LINK
Green
Link status indication
•
OFF: Connection error
•
ON: Normal connection
DATA
Green
Data transmission indication
•
OFF: No data transmitted
•
ON: Data transmitting
Installation Manual
2.6 Installation of the Other Cards
2.6
Installation of the Other Cards
2.6.1
OPB3 Card
Function
Optional 3-slot base card for mounting a maximum of 3 option cards from the following:
•
DPH4 card
•
DPH2 card
•
EIO4 card
•
ECHO16 card
•
MSG4 card
LED
CAUTION
A LITHIUM BATTERY IS USED IN OPB3 CARD. THERE IS A RISK OF EXPLOSION IF BATTERY IS
REPLACED WITH THE INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE
INSTRUCTIONS.
LED Indications
Indication
Colour
Description
CARD STATUS
Green/Red
Card status indication
•
OFF: Power Off
•
Green ON: Normal (all ports are idle)
•
Green Flashing (60 times per minute): Normal (a port is in use)
•
Red ON: Fault (includes reset)
•
Red Flashing (60 times per minute): Out of Service
Installation Manual
123
2.6 Installation of the Other Cards
2.6.2
DPH4 Card
Function
4-port doorphone card for 4 doorphones and 4 door openers. To be mounted on the OPB3 card.
Fully insert the connectors through
the panel openings.
OPB3 Card
DPH4 Card
8-pin
Screw
To doorphones
To door openers
10-pin
Accessory and User-supplied Items
Accessory (included): Screws × 3, 10-pin terminal block × 1, 8-pin terminal block × 1
User-supplied (not included): Copper wire
Note
For details about connection to doorphones and door openers, refer to "2.10.1 Connection of
Doorphones, Door Openers, External Sensors, and External Relays".
124
Installation Manual
2.6 Installation of the Other Cards
Pin Assignments
8-pin Terminal Block
1
8
No.
Signal Name
Function
1
DP4
Doorphone 4 transmit
2
com4
Doorphone 4 receive
3
DP3
Doorphone 3 transmit
4
com3
Doorphone 3 receive
5
DP2
Doorphone 2 transmit
6
com2
Doorphone 2 receive
7
DP1
Doorphone 1 transmit
8
com1
Doorphone 1 receive
No.
Signal Name
Function
1-2
Reserved
–
3
OP4b
Door opener 4
4
OP4a
Door opener 4 com
5
OP3b
Door opener 3
6
OP3a
Door opener 3 com
7
OP2b
Door opener 2
8
OP2a
Door opener 2 com
9
OP1b
Door opener 1
10
OP1a
Door opener 1 com
10-pin Terminal Block
1
10
Installation Manual
125
2.6 Installation of the Other Cards
2.6.3
DPH2 Card
Function
2-port doorphone card for 2 German type doorphones and 2 door openers. To be mounted on the OPB3
card.
Fully insert the connectors through
the panel openings.
OPB3 Card
DPH2 Card
8-pin
Screw
To doorphones/
door openers
10-pin
Accessory and User-supplied Items
Accessory (included): Screws × 3, 10-pin terminal block × 1, 8-pin terminal block × 1
User-supplied (not included): Copper wire
Note
For details about connection to doorphones and door openers, refer to "2.10.1 Connection of
Doorphones, Door Openers, External Sensors, and External Relays".
126
Installation Manual
2.6 Installation of the Other Cards
Pin Assignments
8-pin Terminal Block
1
8
No.
Signal Name
Function
1
Path_2b
Doorphone 2 transmit
2
Path_2a
Doorphone 2 receive
3
Call_2b
Doorphone 2 call button
4
Call_2a
Doorphone 2 call button com
5
Path_1b
Doorphone 1 transmit
6
Path_1a
Doorphone 1 receive
7
Call_1b
Doorphone 1 call button
8
Call_1a
Doorphone 1 call button com
No.
Signal Name
Function
1-2
Reserved
–
3
OP2b
Door opener 2
4
OP2a
Door opener 2 com
5
OP1b
Door opener 1
6
OP1a
Door opener 1 com
7
DC2b
Doorphone control 2
8
DC2a
Doorphone control 2 com
9
DC1b
Doorphone control 1
10
DC1a
Doorphone control 1 com
10-pin Terminal Block
1
10
Installation Manual
127
2.6 Installation of the Other Cards
Connection Diagram for German Type Doorphones and Door Openers
German Type Doorphone 2
8
7
6
5
4
3
2
1
RT
Door
Opener 2
BL
Call_2b
L O U B
Call_2a
~0 V L O U B~12 V~8 V TO
Path_2a
Path_2b
DC2b
DC2a
OP2b
OP2a
Doorphone 2
Adaptor
220 V~
German Type Doorphone 1
RT
Door
Opener 1
BL
Call_1a
10
9
8
7
6
5
4
3
2
1
L O U B
Call_1b
~0 V L O U B~12 V~8 V TO
Path_1a
Path_1b
DC1b
DC1a
OP1b
OP1a
Doorphone 1
Adaptor
220 V~
128
Installation Manual
BL: Light
RT: Call Button
OP: Door Opener Connection Terminal
DC: Doorphone Current Supply Control Terminal
Path: Doorphone Call Path
: Speaker
: Microphone
: Shield
2.6 Installation of the Other Cards
2.6.4
EIO4 Card
Function
4-port external input/output card. To be mounted on the OPB3 card.
Fully insert the connectors through
the panel openings.
OPB3 Card
EIO4 Card
8-pin
Screw
To external sensors
To external relays
10-pin
Accessory and User-supplied Items
Accessory (included): Screws × 3, 10-pin terminal block × 1, 8-pin terminal block × 1
User-supplied (not included): Copper wire
Note
For details about connection to external sensors and external relays, refer to "2.10.1 Connection of
Doorphones, Door Openers, External Sensors, and External Relays".
Installation Manual
129
2.6 Installation of the Other Cards
Pin Assignments
8-pin Terminal Block
1
8
No.
Signal Name
Function
1
C4b
Control 4
2
C4a
Control 4 com
3
C3b
Control 3
4
C3a
Control 3 com
5
C2b
Control 2
6
C2a
Control 2 com
7
C1b
Control 1
8
C1a
Control 1 com
No.
Signal Name
Function
1-2
Reserved
–
3
OP4b
Opener 4
4
OP4a
Opener 4 com
5
OP3b
Opener 3
6
OP3a
Opener 3 com
7
OP2b
Opener 2
8
OP2a
Opener 2 com
9
OP1b
Opener 1
10
OP1a
Opener 1 com
10-pin Terminal Block
1
10
130
Installation Manual
2.6 Installation of the Other Cards
Connection Diagram for External Sensor
Power to the external sensor is provided from the EIO4 card and must be grounded through the EIO4 card
as indicated in the diagram below. A pair of "sensor" and "common" lines are connected to the EIO4 card
for each external sensor. The Hybrid IP-PBX detects input from the sensor when the signal is under 100 Ω.
Hybrid IP-PBX
OPB3
EIO4
+5V
33
10K
I/O
4.7K
External Sensor
+5V
sensor
33
common
4.7K
Installation Manual
131
2.6 Installation of the Other Cards
2.6.5
ECHO16 Card
Function
16-channel card for echo cancellation during conferences. To be mounted on the OPB3 card.
OPB3 Card
inside
ECHO16 Card
Screw
Accessory and User-supplied Items
Accessory (included): Screws × 3
User-supplied (not included): none
Note
To establish a conference call involving 6 to 8 parties, install an ECHO16 card and enable the echo
cancellation for conference using the KX-TDA Maintenance Console. For details, refer to the on-line
help of the KX-TDA Maintenance Console.
132
Installation Manual
2.6 Installation of the Other Cards
2.6.6
MSG4 Card
Function
4-channel message card. To be mounted on the OPB3 card.
OPB3 Card
inside
MSG4 Card
Screw
Accessory and User-supplied Items
Accessory (included): Screws × 3
User-supplied (not included): none
Installation Manual
133
2.6 Installation of the Other Cards
2.6.7
CTI-LINK Card
Function
Ethernet card for CTI communication via 10BASE-T port. CSTA Phase 3 protocol compatible.
LEDs
RJ45 (10BASE-T)
To LAN/
Server PC
Accessory and User-supplied Items
Accessory (included): none
User-supplied (not included): RJ45 connector
Notes
•
•
Maximum length of the cable to be connected to this optional service card is 100 m.
This optional service card can be connected to PCs on a LAN via a Server PC to provide third party
call control CTI.
The operating system of the PC or Server PC required for third party call control depends on your
CTI application software. For details, refer to the manual for your CTI application software.
Pin Assignments
RJ45 Connector (10BASE-T)
8
1
134
Installation Manual
No.
Signal Name
Input (I)/Output (O)
Function
1
TPO+
O
Transmit data+
2
TPO-
O
Transmit data-
3
TPI+
I
Receive data+
4-5
Reserved
–
–
6
TPI-
I
Receive data-
7-8
Reserved
–
–
2.6 Installation of the Other Cards
LED Indications
Indication
Colour
Description
CARD STATUS
Green/Red
Card status indication
•
OFF: Power Off
•
Green ON: Normal
•
Red ON: Fault (includes reset)
•
Red Flashing (60 times per minute): Out of Service
LINK STATUS
Green
Link status indication
•
Flashing: In communication
•
ON: In normal linking
Installation Manual
135
2.7 Connection of Extensions
2.7
Connection of Extensions
2.7.1
Maximum Cabling Distances of the Extension Wiring
(Twisted Cable)
Cable
ø 0.4 mm:
ø 0.5 mm:
ø 0.6 mm:
CAT 5:
Maximum Distance
Under 222 m
Under 347 m
Under 500 m
Under 347 m
Cable
ø 0.4 mm:
ø 0.5 mm:
ø 0.6 mm:
CAT 5:
Maximum Distance
Under 500 m
Under 720 m
Under 830 m
Under 720 m
Cable
ø 0.4 mm:
ø 0.5 mm:
ø 0.6 mm:
CAT 5:
Maximum Distance
Under 140 m
Under 229 m
Under 360 m
Under 229 m
Cable
ø 0.4 mm:
ø 0.5 mm:
ø 0.6 mm:
CAT 5:
Maximum Distance
Under 698 m
Under 1128 m
Under 1798 m
Under 1128 m
PT-interface CS
KX-T7600 Series
Other PT (DPT/APT)
and DSS Console
SLT
Notice
The maximum cabling distance may vary depending on the conditions.
PT-interface
CS
DPT
DHLC8 Card
MSLC16, SLC16, SLC8 Cards
DLC16, DLC8 Cards
"
136
" indicates that the extension card supports the terminal.
Installation Manual
APT
DSS Console
SLT
2.7 Connection of Extensions
2.7.2
Parallel Connection of the Extensions
Any SLT can be connected in parallel with an APT or a DPT as follows.
Note
In addition to an SLT, an answering machine, a fax machine or a modem (PC) can be connected in
parallel with an APT or a DPT.
With APT
To DHLC8 card
Modular
T-Adaptor
2-conductor wiring cord
Connect pins "T" and "R".
4-conductor wiring cord
Connect pins "T", "R", "D1",
and "D2".
APT
SLT
With DPT
Parallel mode or eXtra Device Port (XDP) mode can be selected through system programming.
If the XDP mode is enabled through system programming, parallel connection is not possible. Refer to
"1.10.9 Parallelled Telephone" and "2.1.1 Extension Port Configuration" in the Feature Guide for further
information.
Using a Modular T-Adaptor
To DHLC8 card
Modular
T-Adaptor
2-conductor wiring cord
Connect pins "T" and "R".
4-conductor wiring cord
Connect pins "D1" and
"D2".
DPT
SLT
Installation Manual
137
2.7 Connection of Extensions
Using an EXtra Device Port
With KX-T7600 Series DPT (except KX-T7665)
To DHLC8 card
2-conductor wiring cord
Connect pins "T" and "R".
4-conductor wiring cord
Connect pins "T", "R",
"D1" and "D2".
DPT
SLT
TO MAIN UNIT TO TEL
/ PABX
To DHLC8 card
To SLT
With Other DPT (except KX-T7560 and KX-T7565)
To DHLC8 card
2-conductor wiring cord
Connect pins "T" and "R".
4-conductor wiring cord
Connect pins "T", "R",
"D1" and "D2".
DPT
SLT
TO TEL
TO EMSS or TO MAIN UNIT
To DHLC8 card
138
Installation Manual
To SLT
2.7 Connection of Extensions
2.7.3
Digital EXtra Device Port (Digital XDP) Connection
A DPT can be connected to another DPT on the Digital XDP connection. In addition, if the DPT is connected
to a DHLC8 card, it can also have an SLT connected in Parallel mode or XDP mode.
Notes
•
•
•
Both DPTs must be KX-T7600 series DPTs (excluding KX-T7640).
Parallel mode or XDP mode can be selected through system programming.
If XDP mode is enabled through system programming, parallel connection is not possible. Refer to
"1.10.9 Parallelled Telephone" and "2.1.1 Extension Port Configuration" in the Feature Guide for
further information.
With KX-T7600 Series DPT (except KX-T7600E Series)
Using a Modular T-Adaptor
To DLC8/DLC16 card
Modular
T-Adaptor
To DHLC8 card
(for connection of SLT)
2-conductor wiring cord
Connect pins "T" and "R".
4-conductor wiring cord
Connect pins "D1" and "D2".
4-conductor wiring cord
Connect pins "D1" and
"D2".
SLT
Master DPT
Slave DPT
Back View of DPTs
TO TEL
TO MAIN UNIT
/ PABX
Cable
ø 0.4 mm:
ø 0.5 mm:
ø 0.6 mm:
CAT 5:
TO MAIN UNIT
/ PABX
Maximum Distance
Under 30 m
Under 50 m
Under 60 m
Under 50 m
Master DPT
Slave DPT
To DLC8/DLC16 card
To DHLC8 card
(for connection of SLT)
Installation Manual
139
2.7 Connection of Extensions
Using an EXtra Device Port
To DLC8/DLC16 card
To DHLC8 card
(for connection of SLT)
4-conductor wiring cord
Connect pins "T", "R",
"D1" and "D2".
4-conductor wiring cord
Connect pins "T", "R", 2-conductor wiring cord
"D1" and "D2".
Connect pins "T" and "R".
Master DPT
Slave DPT
SLT
Back View of DPTs
TO MAIN UNIT
/ PABX
TO TEL
Cable
ø 0.4 mm:
ø 0.5 mm:
ø 0.6 mm:
CAT 5:
TO MAIN UNIT
/ PABX
Maximum Distance
Under 30 m
Under 50 m
Under 60 m
Under 50 m
TO TEL
Master DPT
To DLC8/DLC16 card
To DHLC8 card
(for connection of SLT)
140
Installation Manual
Slave DPT
To SLT
2.7 Connection of Extensions
With KX-T7600E Series DPT
Using a Modular T-Adaptor
To DLC8/DLC16 card
Modular
T-Adaptor
To DHLC8 card
(for connection of SLT)
2-conductor wiring cord
Connect pins "T" and "R".
4-conductor wiring cord
Connect pins "D1" and "D2".
4-conductor wiring cord
Connect pins "D1" and "D2".
SLT
Master DPT
Slave DPT
Back View of DPTs
TO DIGITAL
TO MAIN UNIT
/ PABX
Cable
ø 0.4 mm:
ø 0.5 mm:
ø 0.6 mm:
CAT 5:
TO MAIN UNIT
/ PABX
Maximum Distance
Under 30 m
Under 50 m
Under 60 m
Under 50 m
Master DPT
Slave DPT
To DLC8/DLC16 card
To DHLC8 card
(for connection of SLT)
Installation Manual
141
2.7 Connection of Extensions
Using an EXtra Device Port
Connecting to a Slave DPT
To DLC8/DLC16 card
To DHLC8 card
(for connection of SLT)
4-conductor wiring cord
Connect pins "T", "R",
"D1" and "D2".
4-conductor wiring cord
Connect pins "T", "R", 2-conductor wiring cord
"D1" and "D2".
Connect pins "T" and "R".
Master DPT
Slave DPT
SLT
Back View of DPTs
TO MAIN UNIT
/ PABX
TO DIGITAL
Cable
ø 0.4 mm:
ø 0.5 mm:
ø 0.6 mm:
CAT 5:
TO MAIN UNIT
/ PABX
Maximum Distance
Under 30 m
Under 50 m
Under 60 m
Under 50 m
TO TEL
Master DPT
To DLC8/DLC16 card
To DHLC8 card
(for connection of SLT)
142
Installation Manual
Slave DPT
To SLT
2.7 Connection of Extensions
Connecting to a Master DPT
To DLC8/DLC16 card
To DHLC8 card
(for connection of SLT)
4-conductor wiring cord
Connect pins "D1" and "D2".
4-conductor wiring cord
Connect pins "T", "R",
"D1" and "D2".
Master DPT
Slave DPT
2-conductor wiring cord
Connect pins "T" and "R".
SLT
Back View of DPTs
TO MAIN UNIT
/ PABX
To DLC8/DLC16 card
To DHLC8 card
(for connection of SLT)
TO DIGITAL
TO TEL
To slave DPT
Cable
ø 0.4 mm:
ø 0.5 mm:
ø 0.6 mm:
CAT 5:
Maximum Distance
Under 30 m
Under 50 m
Under 60 m
To SLT
Under 50 m
Installation Manual
143
2.7 Connection of Extensions
2.7.4
First Party Call Control CTI Connection
CTI connection between a PC and a KX-T7633/T7636 DPT provides first party call control. The CTI
connection is made via a USB interface (version 1.1), and uses the TAPI 2.1 protocol.
A USB Module (KX-T7601) must be connected to the KX-T7633/T7636 DPT.
Note
The operating system of the PC required for first party call control depends on your CTI application
software. For details, refer to the manual for your CTI application software.
To PC
USB Port
L
UL
USB Cable
USB Module
Notes
•
•
144
Maximum length of the USB cable is 3 m.
USB Modules must not be connected to DPTs in the Digital XDP connection. In a Digital XDP
connection, the PC cannot be used. If a USB module is connected to a slave DPT, the DPT will not
work properly.
Installation Manual
2.8 Connection of DECT Portable Stations
2.8
Connection of DECT Portable Stations
2.8.1
Overview
The following equipment is required to connect the wireless system:
CS: Cell Station (KX-TDA0142CE/KX-TDA0141CE)
KX-TDA0142CE Using a CSIF Card
This unit determines the area covered by the wireless system. Up to 4 calls can be made at the same
time through each CS.
•
CSIF4 (KX-TDA0143)
One CSIF4 card supports up to 4 Cell Stations. Up to 2 CSIF4 cards can be installed in the KXTDA100, and up to 4 can be installed in the KX-TDA200.
•
CSIF8 (KX-TDA0144)
One CSIF8 card supports up to 8 Cell Stations. Up to 2 CSIF8 cards can be installed in the KXTDA100, and up to 4 can be installed in the KX-TDA200.
KX-TDA0141CE Using a DHLC/DLC Card
This unit determines the area covered by the wireless system. Up to 2 calls can be made at the same
time through each CS.
Note for users in Europe
This Cell Station Unit for DECT is for connection to a Panasonic PBX of a European country.
PS: DECT Portable Station (KX-TCA155/KX-TCA255/KX-TD7590/KX-TD7580)
The KX-TDA100 and KX-TDA200 can support up to 128 PSs. For more details about the PS, refer to the
PS Operating Instructions.
RF Specification
Item
Description
Radio Access Method
Multi Carrier TDMA-TDD
Frequency Band
1880 MHz to 1900 MHz*1
Number of Carriers
10*2
Carrier Spacing
1728 kHz
Bit Rate
1152 kbps
Carrier Multiplex
TDMA, 24 (Tx12, Rx12) slots per frame
Frame Length
10 ms
Modulation Scheme
GFSK
Roll-off factor=0.5
50 % roll-off in the transmitter
Data Coding for Modulator
Differential Coding
Voice CODEC
32 kbps ADPCM (CCITT G.721)
Transmission Output
Average 10 mW
Peak 250 mW
Installation Manual
145
2.8 Connection of DECT Portable Stations
*1
*2
The number may vary depending on the country/area. In Taiwan, it is 1880 MHz to 1895 MHz.
The number may vary depending on the country/area. In Taiwan, it is 8.
CAUTION
•
•
•
•
•
•
The CS should be kept free of dust, moisture, high temperature (more than 40 °C), low temperature
(less than 0 °C), vibration, and should not be exposed to direct sunlight.
The CS should not be placed outdoors (use indoors).
The CS should not be placed near high voltage equipment.
The CS should not be placed on a metal object.
Do not use this wireless system near another high power cordless system such as DECT or SS
wireless.
Keep the distances listed below between equipment in order to prevent noise, interference or the
disconnection of a conversation. (The distance may vary depending on the environment.)
Equipment
Distance
CS and office equipment such as a computer, telex, fax
machine, etc., or microwaves
More than 2 m
CS and PS
More than 1 m
Each PS
More than 0.5 m
Hybrid IP-PBX and CS
More than 2 m
Too many CSs in a small area can cause problems due to conflicts over which signal channels
each CS can use. Ideally, CSs should be a minimum of 25 m to 40 m apart.
However, the required distance between CSs may vary depending on the environment of the
installation site and conditions in which the wireless system is used. Conduct the site survey to
determine the appropriate distance.
146
Installation Manual
2.8 Connection of DECT Portable Stations
2.8.2
Procedure Overview
When connecting the wireless system, use extreme care to conduct a site survey. Site surveys can be
conducted using the KX-TCA255 or KX-TD7590 PS. Inadvertent site survey can result in poor service area,
frequent noise, and disconnection of calls.
1. Investigate the installation site
Refer to "2.8.3 Site Planning".
a. Obtain the map of the CS installation site.
b. Consider the service area demanded by the user on the map.
c. Plan the locations of each CS, taking account of distance, building materials and etc.
2. Prepare for site survey
Refer to "2.8.4 Before Site Survey".
a.
b.
c.
d.
Check and assign the CS ID number to the PS.
Assign a channel number to each CS by setting the DIP switches on the back of the CS.
Supply electricity to each CS using an AC adaptor or a battery box.
Install each CS temporarily as planned.
Notes
•
•
Install at least 2 m above the floor.
Keep the antennas in the upright position.
3. Conduct the site survey
Refer to "2.8.5 Site Survey Using the KX-TCA255/KX-TD7590".
a. Test the radio signal strength using the PS.
Confirm that the radio signal strength level is "12" near the CS.
Using the KX-TCA255
To survey
specific channel
1
9
0
Press 1, 9, and POWER
for more than 2 seconds.
Channel No.
Display example:
RADIO STRENGTH
<<< MEASURING >>>
0 to 9
RADIO STRENGTH
CH0 SLOT:06 SYNC
L:12 0000/0100
CS-ID:9005301234
Using the KX-TD7590
To survey
specific channel
1
9
Press 1, 9, and POWER
for more than 5 seconds.
0
Channel No.
0 to 9
Display example:
RADIO STRENGTH
<<< MEASURING >>>
CH0 SLOT:06 SYNC
L:12 0000/0100
CS-ID:9005301234
b. By walking away from the CS with the PS, check the radio signal strength. The radio signal strength
weakens as you walk away from the CS.
c. Map the CS coverage area at radio signal strength levels "3" and "8".
d. Make sure that adjacent CS coverage areas overlap where the radio signal strength level is "8" by
at least 5 m.
Installation Manual
147
2.8 Connection of DECT Portable Stations
e. Make sure that the radio signal strength level is greater than "3" at any location within the service
area demanded by the user.
4. Finish the site survey
Refer to "2.8.6 After Site Survey".
a. Return all DIP switches of each CS to the OFF position, and stop supplying power.
b. Turn off the PS.
5. Connect the CS and PS to the Hybrid IP-PBX and test the operation
Refer to "2.8.7 Connecting a Cell Station to the Hybrid IP-PBX".
a. Connect the CSs to the Hybrid IP-PBX.
b. Register the PSs to the Hybrid IP-PBX.
c. Walk around the service area while having a conversation using a registered PS. If noise is
frequent or conversations disconnect, relocate the CSs or install an additional CS.
6. Mount the CS on the wall
Refer to "2.8.8 Wall Mounting".
a. Assuming everything goes as planned, mount the CS on the wall.
148
Installation Manual
2.8 Connection of DECT Portable Stations
2.8.3
Site Planning
Choosing the best site for the CS requires careful planning and testing of essential areas. The best location
may not always be convenient for installation. Read the following information before installing the unit.
Understanding Radio Waves
Characteristics of Radio Waves
The transmission of radio waves and the CS coverage area depend on the structure and materials of the
building.
Office equipment, such as computers and fax machines, can interfere with radio waves. Such equipment
may create noise or interfere with the performance of the PS.
The illustration below shows the special transmitting patterns of radio waves.
1. Radio waves are reflected by objects such as those made of metal.
2. Radio waves are diffracted by objects such as metallic columns.
3. Radio waves penetrate objects like those made of glass.
CS
1. Reflection
Column
2. Diffraction
3. Penetration
Relationships Between Radio Waves and Building Structure and Materials
•
•
•
•
•
The CS coverage area is affected more by the building materials and their thickness than the number
of obstacles.
Radio waves tend to be reflected or diffracted by conductive objects and rarely penetrate them.
Radio waves tend to penetrate insulated objects and are rarely reflected by them.
Radio waves penetrate thin objects more than thick objects.
The table below shows the transmission tendency of radio waves when they reach objects made from
various materials.
Installation Manual
149
2.8 Connection of DECT Portable Stations
Object
Material
Transmission Tendency
Wall
Concrete
The thicker they are, the less radio waves
penetrate them.
Ferroconcrete
Radio waves can penetrate them, but the more iron
there is, the more radio waves are reflected.
Glass
Radio waves usually penetrate them.
Glass with wire nets
Radio waves can penetrate them, but tend to be
reflected.
Glass covered with heatresistant film
Radio waves are weakened considerably when
they penetrate windows.
Floor
Ferroconcrete
Radio waves can penetrate them, but the more iron
there is, the more radio waves are reflected.
Partition
Steel
Radio waves are reflected and rarely penetrate
them.
Plywood, Glass
Radio waves usually penetrate them.
Ferroconcrete
Radio waves can penetrate them, but the more iron
there is, the more radio waves tend to be reflected
or diffracted.
Metal
Radio waves tend to be reflected or diffracted.
Steel
Radio waves are usually reflected or diffracted,
and rarely penetrate them.
Wood
Radio waves can penetrate them, but they are
weakened.
Window
Column
Cabinet
150
Installation Manual
2.8 Connection of DECT Portable Stations
CS Coverage Area
The example below shows the size of the coverage area of 1 CS if it is installed where there is no obstacle.
Note
Radio signal strength levels are measured during the site survey (refer to "2.8.5 Site Survey Using the
KX-TCA255/KX-TD7590").
A
Coverage Area
Radio signal strength level is
greater than "3".
(About 50 m to 60 m)
A
B
B
Gray Zone:
Conversation will be
intermittent
C
Good Coverage Area
Radio signal strength
level is greater than "8".
(About 30 m to 40 m)
Good conversation
will be kept.
Out of Service:
Cannot make/receive calls
Radio Signal Strength Levels
Level: 00
Level: 01 to 02
Level: 03 to 07
Level: 08 to 10
Level: 11 to 12
Out of range
Receives noise easily or disconnects
May receive noise
Good
Better
Site Survey Preparation
1. Obtain the map and investigate the installation site.
a. Check the obstacles (e.g., shelves, columns, and partitions).
b. Check the materials of the structures (e.g., metal, concrete, and plywood).
c. Check the layout and dimensions of the room, corridor, etc.
d. Write down the above information on the map.
2. Examine the service area demanded by the user on the map, referring to the following example.
a. Draw the coverage area around a CS. Extend the coverage area to 30 m to 60 m in one direction,
depending on the materials of the building structures and obstacles in the installation site. Note
that a CS cannot be installed outside a building.
b. If 1 CS cannot cover the entire service area, install additional CSs as required. Overlap the
coverage areas of adjacent CSs.
Installation Manual
151
2.8 Connection of DECT Portable Stations
Where CS coverage areas overlap, the PS will start call handover to the next CS if the signal from
one CS becomes weak. However, if a PS moves away from a CS and there are no CSs available
for handover, the PS may go out of range and the call could be lost.
Example: Installing in a Room Separated by Walls
Things to take note of:
•
The room is separated by walls.
•
The room is surrounded by concrete walls.
CS installation plan:
•
The coverage area of each CS will not extend as much it does where there is no obstacle, because
the radio signals will be weakened by separating walls. Therefore, you will need 5 CSs to cover the
entire room.
150 m
70 m
CS no. 1
CS no. 2
CS no. 5
CS no. 3
152
Installation Manual
CS no. 4
2.8 Connection of DECT Portable Stations
2.8.4
Before Site Survey
Use the KX-TCA255 or KX-TD7590 PS to conduct the site survey.
Note
The display language for the site survey is only in English.
Checking the CS ID Number
Check the CS ID number label attached to the CS. If the CS ID number label is not attached to the CS, check
the CS ID number using the KX-TDA Maintenance Console. For details, refer to the on-line help of the KXTDA Maintenance Console.
Assigning the CS ID Number to the PS
Using the KX-TCA255
To enter letters
9
1
ABC
2
Press 1, 9, and POWER
for more than 2 seconds.
A:
+
0
C:
+
ABC
2
E:
+
GHI
4
B:
+
1
D:
+
DEF
3
F:
+
JKL
5
CS No.
CS ID No.
0 to 7
0 to 9 and A to F
To the Desired CS No.
To the initial display
Note
To clear the CS ID number assigned to the PS, follow the procedure below:
To clear one by one
CS No.
0 to 7
1
9
DEF
3
To the Desired CS No.
Press 1, 9, and POWER
for more than 2 seconds.
OR
To clear all at once
To the initial display
#
Installation Manual
153
2.8 Connection of DECT Portable Stations
Using the KX-TD7590
To enter letters
9
1
ABC
2
Press 1, 9, and POWER
for more than 5 seconds.
A:
F1
C:
F3
E:
B:
F2
D:
INT'
F:
CS No.
CS ID No.
0 to 7
0 to 9 and A to F
OK
To the Desired CS No.
To the initial display
Note
To clear the CS ID number assigned to the PS, follow the procedure below:
To clear one by one
CS No.
0 to 7
1
9
DEF
3
To the Desired CS No.
Press 1, 9, and POWER
for more than 5 seconds.
OR
To clear all at once
To the initial display
154
Installation Manual
#
2.8 Connection of DECT Portable Stations
Setting and Installing the CS Temporarily for Site Survey
1. Switch the Radio Signal Test switch from OFF to ON.
2. Set the channel number switches as desired.
DIP Switch
OFF
ON
1
2
Channel Number Switch
3
4
5
6
Radio Signal
Test Switch
Channel 0
Channel 1 Channel 2 Channel 3 Channel 4 Channel 5 Channel 6 Channel 7 Channel 8 Channel 9
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
Notes
•
•
To see the radio signal strength of more than 1 CS, a channel number must be set for each CS.
If more than 1 CS is in Radio Signal Test mode, each CS must have a unique channel number.
Installation Manual
155
2.8 Connection of DECT Portable Stations
3. After setting the DIP switch, connect an AC adaptor or battery box to the CS using a power supply
adaptor.
Notes
•
•
The AC adaptor should be connected to a vertically oriented or floor-mounted AC outlet. Do not
connect the AC adaptor to a ceiling-mounted AC outlet, as the weight of the adaptor may cause it
to become disconnected.
For users in the United Kingdom:
240 V AC must not be used on a building site. Instead of an AC adaptor, connect a battery box to
the CS.
Telephone Cord
Modular
Power Supply Adaptor
(PSZZ1TDA0142)
To AC Adaptor (KX-A11/KX-TCA1)/
Battery Box (PSZZTD142CE)
4. Install the CS temporarily for the site survey. Install the CS at least 2 m above the floor, keeping the
antennas in the upright position.
156
Installation Manual
2.8 Connection of DECT Portable Stations
2.8.5
Site Survey Using the KX-TCA255/KX-TD7590
The PS has a Radio Signal Test mode that monitors the state of the radio link to the CS for site survey. In
the Radio Signal Test mode, the frame loss and signal strength of a synchronous slot, and the signal
strength of the other slots can be measured when the PS is monitoring the CS. After installing the CSs
temporarily as planned during site planning, set the PS to the Radio Signal Test mode and locate each CS
to measure its coverage area. Then, record the results on the map of the installation site.
Testing the Radio Signal Strength
After locating the CS(s) temporarily, execute the Radio Signal Test using the PS. The PS scans whether
there is a CS that can link with on channel 0 right after entering the Radio Signal Test mode. The channel
to be scanned can be changed by pressing the appropriate keys 0 through 9.
1. Enter the Radio Signal Test mode.
Using the KX-TCA255
To survey other slots
9
1
Press 1, 9, and POWER
for more than 2 seconds.
To survey specific channel
/
Channel No.
Previous or Next
0 to 9
0
Display example:
To store the scan data
RADIO STRENGTH
<<< MEASURING >>>
RADIO STRENGTH
CH0*1 SLOT:06*2 SYNC*3
L:12*4 0000/0100*5
CS-ID:9005301234
Log No.
0 to 9
Using the KX-TD7590
To survey other slots
9
1
Press 1, 9, and POWER
for more than 5 seconds.
0
/
Channel No.
Previous or Next
0 to 9
To store the scan data
Display example:
RADIO STRENGTH
<<< MEASURING >>>
To survey specific channel
CH0*1 SLOT:06*2 SYNC*3
L:12*4 0000/0100*5
CS-ID:9005301234
Log No.
0 to 9
Notes
*1: Channel number
*2: Slot number
*3: When a slot is synchronised, "SYNC" is displayed.
*4: Radio signal strength level
*5: Frame error (0000 to 9999)/Frame counter (0000 to 9999). Frame error indicates the number of
errors out of 10 000 radio signal receptions. An increased number of frame errors indicates greater
radio signal interference and more frequent noise during conversation. The ideal number of frame error
is "0000".
CAUTION
Storing the scan data will clear all directory data.
2. Measure the radio signal strength by moving to and away from the CS.
Installation Manual
157
2.8 Connection of DECT Portable Stations
a. Move to the CS until the point the radio signal strength level becomes "12".
b. Move away from the CS and identify the CS coverage area within which the radio signal strength
level is greater than "8". Draw the area on the map.
c. Move away from the CS and identify the CS coverage area within which the radio signal strength
level is greater than "3". Draw the area on the map.
PS
Channel no. 0
CH0
L:12
PS
CH0
L:08
PS
CH0
L:03
Radio Signal Strength Levels
Level: 00
Level: 01 to 02
Level: 03 to 07
Level: 08 to 10
Level: 11 to 12
158
Installation Manual
Out of range
Receives noise easily or disconnects
May receive noise
Good
Better
2.8 Connection of DECT Portable Stations
3. Repeat the steps 1 and 2 for other CSs, and relocate the CSs when necessary.
a. Overlap adjacent CS coverage areas where the radio signal strength level is "8" by 5 m to 10 m.
Channel no. 0
5 m to 10 m
Channel no. 1
b. Overlap the CS coverage areas of at least 2 CSs at any location in the installation site.
Channel no. 0
Channel no. 1
Channel no. 2
Channel no. 3
c. Make sure that the radio signal strength level is greater than "3" at any location in the service area
demanded by the user.
Notes
•
•
If a channel is set, the results of measurement for the 24 slots on the channel are saved each time.
If the same channel is set, the new results override the previous ones. Therefore, a measurement
of 10 channels × 24 slots in total can be made.
If correct results cannot be obtained (e.g., there are many error counters), change the location of
the CS and repeat the site survey to select the best location.
Installation Manual
159
2.8 Connection of DECT Portable Stations
Referring to the Stored Scan Data
Using the KX-TCA255
9
1
1
Log No.
0 to 9
Press 1, 9, and POWER
for more than 2 seconds.
To go to other slots
To go to specific channel
/
Channel No.
Previous or Next
0 to 9
A a
Using the KX-TD7590
1
9
1
Log No.
0 to 9
Press 1, 9, and POWER
for more than 5 seconds.
To go to other slots
To go to specific channel
/
Channel No.
Previous or Next
0 to 9
Clearing the Stored Scan Data
When "CLEAR SCAN DATA" is displayed after turning on the PS, you are required to clear the scan data.
Using the KX-TCA255
1
9
GHI
4
GHI
4
Press 1, 9, and POWER
for more than 2 seconds.
Using the KX-TD7590
1
9
Press 1, 9, and POWER
for more than 5 seconds.
160
Installation Manual
2.8 Connection of DECT Portable Stations
2.8.6
After Site Survey
After obtaining the proper measurement results, exit the Radio Signal Test mode before connecting the CS
to the Hybrid IP-PBX.
1. Keep pressing POWER button on the PS until the PS is turned OFF.
2. Disconnect the AC adaptor or battery box from the CS and stop supplying electricity.
3. Switch all DIP switches on the CS from ON to OFF.
OFF
ON
1
2
3
4
5
6
Installation Manual
161
2.8 Connection of DECT Portable Stations
2.8.7
Connecting a Cell Station to the Hybrid IP-PBX
Using a CSIF Card
Refer to the following example to connect a CS to the Hybrid IP-PBX.
CSIF8 Card
Port 1
Cable
ø 0.4 mm:
ø 0.5 mm:
ø 0.6 mm:
CAT 5:
Maximum Distance
Under 444 m
Under 694 m
Under 1000 m
Under 694 m
CSIF card (RJ45)
CS (RJ11)
Signal Name
D1
POWH
POWL
D2
Pin No.
1
2
3
4
Pin No.
1
2
3
4
5
6
7
8
Signal Name
Accessory and User-supplied Items for the CS
Accessory (included): Screws × 2, Washers × 2, Ferrite core × 1
User-supplied (not included): RJ11 connector
Note
For details about CSIF card, refer to "2.5.1 CSIF4 and CSIF8 Card".
162
Installation Manual
D1
POWH
POWL
D2
2.8 Connection of DECT Portable Stations
Using a DHLC/DLC Card
Refer to the following example to connect a CS to the Hybrid IP-PBX.
DHLC8 Card
Cable
ø 0.4 mm:
ø 0.5 mm:
ø 0.6 mm:
CAT 5:
Maximum Distance
Under 222 m
Under 347 m
Under 500 m
Under 347 m
CS (RJ11)
Signal Name
D1
D2
Pin No.
1
2
3
4
DHLC/DLC card
(Amphenol)
Signal Name
D1
D2
Accessory and User-supplied Items for the CS
Accessory (included): Screws × 2, Washers × 2
User-supplied (not included): RJ11 connector
Note
For details about DHLC card or DLC card, refer to "2.5.2 DHLC8 Card", "2.5.3 DLC8 Card", or "2.5.4
DLC16 Card" .
Installation Manual
163
2.8 Connection of DECT Portable Stations
Connecting the CS
1. Connect the cable from the CSIF/DHLC/DLC card to the CS.
Modular
To CSIF/DHLC/DLC card
2. Pass the cable through the groove of the CS (in any direction depending on your preference).
TO MAIN UNIT
/ PABX
To CSIF/DHLC/DLC card
164
Installation Manual
2.8 Connection of DECT Portable Stations
For the KX-TDA0142CE User only:
3. Wrap the cable once around the ferrite core. Then close the case of the ferrite core.
To CSIF card
Note
If you need to open the ferrite core, use a flathead screwdriver to unlatch the case of the ferrite core.
Installation Manual
165
2.8 Connection of DECT Portable Stations
Registering the PS
The PS must be registered to the Hybrid IP-PBX before it can be used. Programming of both the PS and
Hybrid IP-PBX is required. A PT with multiline display (e.g., KX-T7636 6-line display) is required for the
Hybrid IP-PBX system programming.
Note
For details about system programming using a PT, refer to "2.3.2 PT Programming" and "3.3 PT
Programming" in the Feature Guide.
Entering the Hybrid IP-PBX System Programming Mode Using a PT
Administrator Level
#
PROGRAM/
PAUSE
System Password for Administrator—
for PT Programming
Programming No.
= 1234
3 digits
Note
means default value.
PS Registration
One PS can be registered to a maximum of 4 different Hybrid IP-PBXs.
[690]
ENTER
PS No.
Extn. No.
001 to 128
1 to 4 digits
ENTER
To the PS
operation
below
Using the KX-TCA155/KX-TCA255
Press POWER
for 2 seconds.
Select
"Setting Handset".
Select
"Registration".
"Please wait".
Select
"Register H/set".
"Enter Base PIN".
Select
"Base 1–4".
PIN for PS Registration
4 digits
166
Installation Manual
C.Tone
END
2.8 Connection of DECT Portable Stations
Using the KX-TD7590
System lock can be set after PS registration. When system lock is enabled, the system lock password
will be required for system setting.
F
F
Press POWER
for 5 seconds.
To register for the first time
SELECT
/
Select
"INITIAL SETTING".
OR
To re-register
If required
SELECT
/
Select
"PS-PROGRAM".
Select
"REGISTRATION".
/OK
System Lock Password
Select "DECTSYS SETTING".
SELECT
/
SELECT
/
4 digits
SELECT
/
Select
"DECT-SYS1-4"
PIN for
PS Registration
/OK
C.Tone
4 digits
To set system lock
SELECT
/
Choose
"ENABLE/DISABLE".
4 digits
DISABLE
System Lock Password
/OK
System Lock Password
ENABLE
/OK
4 digits
Using the KX-TD7580
/
Press POWER
for 2 seconds.
/
Select
"Register H/set".
Select
"Setting Handset".
/
Select
"Base 1–4".
/
Select
"Registration".
PIN for
PS Registration
C.Tone
4 digits
Installation Manual
167
2.8 Connection of DECT Portable Stations
Setting the Personal Identification Number (PIN) for PS Registration
To prevent registering the PS to a wrong Hybrid IP-PBX, a PIN for PS registration can be set to the Hybrid
IP-PBX. Before registering the PS to the Hybrid IP-PBX, register the PIN set to the Hybrid IP-PBX into the
PS. By doing so, the PS will only be registered to the Hybrid IP-PBX with the matching PIN.
Notes
•
By default, the PIN for PS registration is "1234" for both the Hybrid IP-PBX and PS. Therefore, the
PS can be registered to the Hybrid IP-PBX without setting the PIN.
•
The PIN for PS registration will only be used when registering the PS to the Hybrid IP-PBX.
Therefore, even when there is more than 1 Hybrid IP-PBX with the same PIN near the PS, the PS
will not be linked to a different Hybrid IP-PBX during normal operation after registration.
Setting the PIN for Hybrid IP-PBX
[692]
PIN for PS Registration
1 to 4 digits
1234
ENTER
END
ENTER
Changing the Display Language of the PS
Using the KX-TCA155/KX-TCA255
Press POWER
for 2 seconds.
Select
"Setting Handset".
Select
"Select Language".
Select
"Display Option".
Select the desired
language.
Using the KX-TD7590
F
0
/
Press POWER
for 5 seconds.
SELECT
/
Select
"DISPLAY SETTING".
SELECT
Select
"LANGUAGE".
SELECT
/
Select the desired
language.
Using the KX-TD7580
/
Press POWER
for 2 seconds.
168
/
Select
"Setting Handset".
/
/
Select "Select
Language".
Select the desired
language.
Installation Manual
Select
"Display Option".
SELECT
2.8 Connection of DECT Portable Stations
PS Termination
Confirm the following before cancelling the PS registration:
•
PS is turned on.
•
PS is within the range.
[691]
PS No.
001 to 128
ENTER
ENTER
If "Rejected" or "Time out" is displayed
CLEAR
YES
Press "CLEAR".
To the PS
operation
below
END
Press "YES".
If the registration information is still stored in the PS
Using the KX-TCA155/KX-TCA255
Press POWER
for 2 seconds.
Select
"Setting Handset".
Select
"Registration".
Select
"Cancel Base".
Handset PIN
C.Tone
4 digits
Select
"Base 1–4".
Select
"YES".
Using the KX-TD7590
F
0
SELECT
/
Press POWER
for 5 seconds.
Select "DECTSYS SETTING".
If required
/
/
Select the
desired item.
Select "CANCEL
DECT-SYS".
4 digits
SELECT
SELECT
/
/OK
System Lock Password
SELECT
C.Tone
Select "YES".
Using the KX-TD7580
/
Press POWER
for 2 seconds.
/
Select
"Setting Handset".
Select
"Registration".
/
Handset PIN
/
Select
"Cancel Base".
4 digits
Select the
desired item.
/
Select "YES".
C.Tone
Installation Manual
169
2.8 Connection of DECT Portable Stations
Testing the Operation
Walk around the service area while having a conversation using a registered PS. If noise is frequent or
conversations disconnect, relocate the CSs or install an additional CS.
170
Installation Manual
2.8 Connection of DECT Portable Stations
2.8.8
Wall Mounting
1. Place the reference for wall mounting (on the following page) on the wall to mark the 2 screw positions.
2. Install the 2 screws and washers (included) into the wall.
Notes
•
•
Make sure that the screw heads are at the same distance from the wall.
Install the screws perpendicular to the wall.
3. Hook the CS on the screw heads.
Installation Manual
171
2.8 Connection of DECT Portable Stations
Reference for Wall Mounting
Please copy this page and use as a reference for wall mounting.
Install a screw here.
71 mm
Install a screw here.
Note
Make sure to set the print size to correspond with the size of this page. If the dimension of the paper
output still deviates slightly from the measurement indicated here, use the measurement indicated
here.
172
Installation Manual
2.9 Connection of 2.4 GHz Portable Stations
2.9
Connection of 2.4 GHz Portable Stations
2.9.1
Overview
The following equipment is required to connect the wireless system:
CS: Cell Station (KX-TDA0142/KX-TDA0141)
KX-TDA0142 Using a CSIF Card
This unit determines the area covered by the wireless system. Up to 3 calls can be made at the same
time through each CS.
•
CSIF4 (KX-TDA0143)
One CSIF4 card supports up to 4 Cell Stations. Up to 2 CSIF4 cards can be installed in the KXTDA100, and up to 4 can be installed in the KX-TDA200.
•
CSIF8 (KX-TDA0144)
One CSIF8 card supports up to 8 Cell Stations. Up to 2 CSIF8 cards can be installed in the KXTDA100, and up to 4 can be installed in the KX-TDA200.
KX-TDA0141 Using a DHLC/DLC Card
This unit determines the area covered by the wireless system. Up to 2 calls can be made at the same
time through each CS.
PS: 2.4 GHz Portable Station (KX-TD7680/KX-TD7690)
The KX-TDA100 and KX-TDA200 can support up to 128 PSs. For more details about the PS, refer to the
PS Operating Instructions.
CAUTION
•
•
•
•
•
•
The CS should be kept free of dust, moisture, high temperature (more than 40 °C), low temperature
(less than 0 °C), vibration, and should not be exposed to direct sunlight.
The CS should not be placed outdoors (use indoors).
The CS should not be placed near high voltage equipment.
The CS should not be placed on a metal object.
Systems using 2.4 GHz ISM (Industrial, Scientific and Medical) band may interfere with the KXTDA wireless system. Examples of such systems are cordless telephones, wireless LAN, Home
RF, microwave ovens and other ISM devices. These systems may cause minor noise.
Keeping some distance between the equipment listed below may prevent interference. (The
distance may vary depending on the environment.)
Equipment
Distance
CS and office equipment such as a computer, telex, fax
machine, etc.
More than 2 m
CS and PS
More than 1 m
Each PS
More than 0.5 m
Hybrid IP-PBX and CS
More than 2 m
CS and CS
More than 15 m
Installation Manual
173
2.9 Connection of 2.4 GHz Portable Stations
Please take into consideration the distance between the CSs when site planning. Please consult
a certified dealer for details.
However, the required distance between CSs may vary depending on the environment of the
installation site and conditions in which the wireless system is used. Conduct the site survey to
determine the appropriate distance.
174
Installation Manual
2.9 Connection of 2.4 GHz Portable Stations
2.9.2
Procedure Overview
When connecting the wireless system, use extreme care to conduct a site survey. Inadvertent site survey
can result in poor service area, frequent noise, and disconnection of calls.
1. Investigate the installation site
Refer to "2.9.3 Site Planning".
a. Obtain the map of the CS installation site.
b. Consider the service area demanded by the user on the map.
c. Plan the locations of each CS, taking account of distance, building materials and etc.
2. Prepare the CS for site survey
Refer to "2.9.4 Before Site Survey".
a. Assign a CS number to each CS by setting the DIP switches on the back of the CS.
b. Supply electricity to each CS using an AC adaptor or a battery box.
c. Install each CS temporarily as planned.
Notes
•
•
Install at least 2 m above the floor.
Keep the antennas in the upright position.
3. Conduct the site survey
Refer to "2.9.5 Site Survey".
a. Test the radio signal strength using the PS.
Confirm that the radio signal strength level is "12" near the CS.
Using the KX-TD7680
Display example:
1
9
0
Press 1, 9, and POWER
for more than 2 seconds.
CS No.
CS NO.1 LEVEL:12
<< SEARCHING >>
SAVE:0123456789
1 to 9
Using the KX-TD7690
Display example:
1
9
Press 1, 9, and POWER
for more than 2 seconds.
CS No.
1 to 9
CS NO.1 LEVEL:12
<< SEARCHING >>
SAVE:0123456789
b. By walking away from the CS with the PS, check the radio signal strength. The radio signal strength
weakens as you walk away from the CS.
c. Map the CS coverage area at radio signal strength levels "3" and "8".
d. Make sure that adjacent CS coverage areas overlap where the radio signal strength level is "8" by
at least 5 m.
e. Make sure that the radio signal strength level is greater than "3" at any location within the service
area demanded by the user.
Installation Manual
175
2.9 Connection of 2.4 GHz Portable Stations
4. Finish the site survey
Refer to "2.9.6 After Site Survey".
a. Return all DIP switches of each CS to the OFF position, and stop supplying power.
b. Turn off the PS.
5. Connect the CS and PS to the Hybrid IP-PBX and test the operation
Refer to "2.9.7 Connecting a Cell Station to the Hybrid IP-PBX".
a. Connect the CSs to the Hybrid IP-PBX.
b. Register the PSs to the Hybrid IP-PBX.
c. Walk around the service area while having a conversation using a registered PS. If noise is
frequent or conversations disconnect, relocate the CSs or install an additional CS.
6. Mount the CS on the wall
Refer to "2.9.8 Wall Mounting".
a. Assuming everything goes as planned, mount the CS on the wall.
176
Installation Manual
2.9 Connection of 2.4 GHz Portable Stations
2.9.3
Site Planning
Choosing the best site for the CS requires careful planning and testing of essential areas. The best location
may not always be convenient for installation. Read the following information before installing the unit.
Understanding Radio Waves
Characteristics of Radio Waves
The transmission of radio waves and the CS coverage area depend on the structure and materials of the
building.
Office equipment, such as computers and fax machines, can interfere with radio waves. Such equipment
may create noise or interfere with the performance of the PS.
The illustration below shows the special transmitting patterns of radio waves.
1. Radio waves are reflected by objects such as those made of metal.
2. Radio waves are diffracted by objects such as metallic columns.
3. Radio waves penetrate objects like those made of glass.
CS
1. Reflection
Column
2. Diffraction
3. Penetration
Relationships Between Radio Waves and Building Structure and Materials
•
•
•
•
•
The CS coverage area is affected more by the building materials and their thickness than the number
of obstacles.
Radio waves tend to be reflected or diffracted by conductive objects and rarely penetrate them.
Radio waves tend to penetrate insulated objects and are rarely reflected by them.
Radio waves penetrate thin objects more than thick objects.
The table below shows the transmission tendency of radio waves when they reach objects made from
various materials.
Installation Manual
177
2.9 Connection of 2.4 GHz Portable Stations
Object
Material
Transmission Tendency
Wall
Concrete
The thicker they are, the less radio waves
penetrate them.
Ferroconcrete
Radio waves can penetrate them, but the more iron
there is, the more radio waves are reflected.
Glass
Radio waves usually penetrate them.
Glass with wire nets
Radio waves can penetrate them, but tend to be
reflected.
Window
Glass covered with heat- Radio waves are weakened considerably when
resistant film
they penetrate windows.
Floor
Ferroconcrete
Radio waves can penetrate them, but the more iron
there is, the more radio waves are reflected.
Partition
Steel
Radio waves are reflected and rarely penetrate
them.
Plywood, Glass
Radio waves usually penetrate them.
Ferroconcrete
Radio waves can penetrate them, but the more iron
there is, the more radio waves tend to be reflected
or diffracted.
Metal
Radio waves tend to be reflected or diffracted.
Steel
Radio waves are usually reflected or diffracted,
and rarely penetrate them.
Wood
Radio waves can penetrate them, but they are
weakened.
Column
Cabinet
178
Installation Manual
2.9 Connection of 2.4 GHz Portable Stations
CS Coverage Area
The example below shows the size of the coverage area of 1 CS if it is installed where there is no obstacle.
Note
Radio signal strength levels are measured during the site survey (refer to "2.9.5 Site Survey").
A
Coverage Area
Radio signal strength level is
greater than "3".
(About 50 m to 60 m)
A
B
B
Gray Zone:
Conversation will be
intermittent
C
Good Coverage Area
Radio signal strength
level is greater than "8".
(About 30 m to 40 m)
Good conversation
will be kept.
Out of Service:
Cannot make/receive calls
Radio Signal Strength Levels
Level: 00
Level: 01 to 02
Level: 03 to 07
Level: 08 to 10
Level: 11 to 12
Out of range
Receives noise easily or disconnects
May receive noise
Good
Better
Site Survey Preparation
1. Obtain the map and investigate the installation site.
a. Check the obstacles (e.g., shelves, columns, and partitions).
b. Check the materials of the structures (e.g., metal, concrete, and plywood).
c. Check the layout and dimensions of the room, corridor, etc.
d. Write down the above information on the map.
2. Examine the service area demanded by the user on the map, referring to the following example.
a. Draw the coverage area around a CS. Extend the coverage area to 30 m to 60 m in one direction,
depending on the materials of the building structures and obstacles in the installation site. Note
that a CS cannot be installed outside a building.
b. If one CS cannot cover the entire service area, install additional CSs as required. Overlap the
coverage areas of adjacent CSs.
Where CS coverage areas overlap, the PS will start call handover to the next CS if the signal from
Installation Manual
179
2.9 Connection of 2.4 GHz Portable Stations
one CS becomes weak. However, if a PS moves away from a CS and there are no CSs available
for handover, the PS may go out of range and the call could be lost.
If the signal from the CS fades, due to the structure of the building, there may be some handover
delay. The user will hear a range warning before handover in this case. This also applies in the case
of interference from 2.4 GHz apparatus.
Example: Installing in a Room Separated by Walls
Things to take note of:
•
The room is separated by walls.
•
The room is surrounded by concrete walls.
CS installation plan:
•
The coverage area of each CS will not extend as much it does where there is no obstacle, because
the radio signals will be weakened by separating walls. Therefore, you will need 5 CSs to cover the
entire room.
150 m
70 m
CS no. 1
CS no. 2
CS no. 5
CS no. 3
180
Installation Manual
CS no. 4
2.9 Connection of 2.4 GHz Portable Stations
2.9.4
Before Site Survey
Setting and Installing the CS Temporarily for Site Survey
1. Switch the Radio Signal Test switch from OFF to ON.
2. Set the CS number switches as desired.
DIP Switch
OFF
ON
1
2
CS Number Switch
3
4
5
6
CS no. 1
CS no. 2
CS no. 3
CS no. 4
Radio Signal
Test Switch
CS no. 5
CS no. 6
CS no. 7
CS no. 8
CS no. 9
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
Notes
•
•
To see the radio signal strength of more than 1 CS, a CS number must be set for each CS.
If more than 1 CS is in Radio Signal Test mode, each CS must have a unique CS number.
Installation Manual
181
2.9 Connection of 2.4 GHz Portable Stations
3. After setting the DIP switch, connect an AC adaptor or battery box to the CS using a power supply
adaptor.
Note
The AC adaptor should be connected to a vertically oriented or floor-mounted AC outlet. Do not connect
the AC adaptor to a ceiling-mounted AC outlet, as the weight of the adaptor may cause it to become
disconnected.
Telephone Cord
Modular
Power Supply Adaptor
(PSZZ1TDA0142)
To AC Adaptor (KX-A11/KX-TCA1)/
Battery Box (PSZZTD142CE)
4. Install the CS temporarily for the site survey. Install the CS at least 2 m above the floor, keeping the
antennas in the upright position.
182
Installation Manual
2.9 Connection of 2.4 GHz Portable Stations
2.9.5
Site Survey
The PS has a Radio Signal Test mode that monitors the state of the radio link to the CS. After installing the
CSs temporarily, set the PS to the Radio Signal Test mode and measure each CS coverage area. Then,
record the results on the map of the installation site.
Testing the Radio Signal Strength
Note
The display language for the site survey is only in English.
1. Enter the Radio Signal Test mode.
Using the KX-TD7680
Display example:
1
0
9
CS No.
CS NO.1 LEVEL:12*1
<< SEARCHING >>
1 to 9
Press 1, 9, and POWER
for more than 2 seconds.
SAVE:0123456789*2
To store the scan data
Scan Data No.
0 to 9
Using the KX-TD7690
Display example:
1
9
0
Press 1, 9, and POWER
for more than 2 seconds.
CS No.
1 to 9
CS NO.1 LEVEL:12*1
<< SEARCHING >>
SAVE:0123456789*2
To store the scan data
Scan Data No.
0 to 9
Notes
*1: CS number and radio signal strength level.
*2: Scan data (test result) number. Empty memory space will be indicated by a number; stored memory
space will be indicated by a "-".
Installation Manual
183
2.9 Connection of 2.4 GHz Portable Stations
2. Measure the radio signal strength by moving to and away from the CS.
a. Move to the CS until the point the radio signal strength level becomes "12".
b. Move away from the CS and identify the CS coverage area within which the radio signal strength
level is greater than "8". Draw the area on the map.
c. Move away from the CS and identify the CS coverage area within which the radio signal strength
level is greater than "3". Draw the area on the map.
PS
CS NO.1 LEVEL:12
CS no. 1
PS
CS NO.1 LEVEL:8
PS
CS NO.1 LEVEL:3
Radio Signal Strength Levels
Level: 00
Level: 01 to 02
Level: 03 to 07
Level: 08 to 10
Level: 11 to 12
Out of range
Receives noise easily or disconnects
May receive noise
Good
Better
3. Repeat the steps 1 and 2 for other CSs, and relocate the CSs when necessary.
a. Overlap adjacent CS coverage areas where the radio signal strength level is "8" by 5 m to 10 m.
CS no. 1
184
Installation Manual
5 m to 10 m
CS no. 2
2.9 Connection of 2.4 GHz Portable Stations
b. Overlap the CS coverage areas of at least 2 CSs at any location in the installation site.
CS no. 1
CS no. 2
CS no. 3
CS no. 4
c. Make sure that the radio signal strength level is greater than "3" at any location in the service area
demanded by the user.
Referring to the Stored Scan Data
Using the KX-TD7680
1
9
1
Scan Data No.
0 to 9
Press 1, 9, and POWER
for more than 2 seconds.
Display example:
When there is scan data
NO.1
CS No.2 LEVEL: 9
When there is no scan data
NO.0
NOT SAVED
To the Desired Scan Data No.
Using the KX-TD7690
1
9
Press 1, 9, and POWER
for more than 2 seconds.
1
Scan Data No.
0 to 9
Display example:
When there is scan data
NO.1
CS No.2 LEVEL: 9
When there is no scan data
NO.0
NOT SAVED
To the Desired Scan Data No.
Installation Manual
185
2.9 Connection of 2.4 GHz Portable Stations
Deleting the Stored Scan Data
Using the KX-TD7680
1
9
2
Scan Data No.
0 to 9, or # for all data
Press 1, 9, and POWER
for more than 2 seconds.
To the Desired Scan Data No.
Using the KX-TD7690
1
9
Press 1, 9, and POWER
for more than 2 seconds.
2
Scan Data No.
0 to 9, or # for all data
To the Desired Scan Data No.
186
Installation Manual
2.9 Connection of 2.4 GHz Portable Stations
2.9.6
After Site Survey
After obtaining the proper measurement results, exit the Radio Signal Test mode before connecting the CS
to the Hybrid IP-PBX.
1. Keep pressing POWER button on the PS until the PS is turned OFF.
2. Disconnect the AC adaptor or battery box from the CS and stop supplying electricity.
3. Switch all DIP switches on the CS from ON to OFF.
OFF
ON
1
2
3
4
5
6
Installation Manual
187
2.9 Connection of 2.4 GHz Portable Stations
2.9.7
Connecting a Cell Station to the Hybrid IP-PBX
Using a CSIF Card
Refer to the following example to connect a CS to the Hybrid IP-PBX.
CSIF8 Card
Port 1
Cable
ø 0.4 mm:
ø 0.5 mm:
ø 0.6 mm:
CAT 5:
Maximum Distance
Under 444 m
Under 694 m
Under 1000 m
Under 694 m
CSIF card (RJ45)
CS (RJ11)
Signal Name
D1
POWH
POWL
D2
Pin No.
1
2
3
4
Pin No.
1
2
3
4
5
6
7
8
Signal Name
Accessory and User-supplied Items for the CS
Accessory (included): Screws × 2, Washers × 2
User-supplied (not included): RJ11 connector
Note
For details about CSIF card, refer to "2.5.1 CSIF4 and CSIF8 Card".
188
Installation Manual
D1
POWH
POWL
D2
2.9 Connection of 2.4 GHz Portable Stations
Using a DHLC/DLC Card
Refer to the following example to connect a CS to the Hybrid IP-PBX.
DHLC8 Card
Cable
ø 0.4 mm:
ø 0.5 mm:
ø 0.6 mm:
CAT 5:
Maximum Distance
Under 222 m
Under 347 m
Under 500 m
Under 347 m
CS (RJ11)
Signal Name
D1
D2
Pin No.
1
2
3
4
DHLC/DLC card
(Amphenol)
Signal Name
D1
D2
Accessory and User-supplied Items for the CS
Accessory (included): Screws × 2, Washers × 2
User-supplied (not included): RJ11 connector
Note
For details about DHLC card or DLC card, refer to "2.5.2 DHLC8 Card", "2.5.3 DLC8 Card", or "2.5.4
DLC16 Card".
Installation Manual
189
2.9 Connection of 2.4 GHz Portable Stations
Connecting the CS
1. Connect the cable from the CSIF/DHLC/DLC card to the CS.
Modular
To CSIF/DHLC/DLC card
2. Pass the cable through the groove of the CS (in any direction depending on your preference).
TO MAIN UNIT
/ PABX
To CSIF/DHLC/DLC card
190
Installation Manual
2.9 Connection of 2.4 GHz Portable Stations
Registering the PS
The PS must be registered to the Hybrid IP-PBX before it can be used. Programming of both the PS and
Hybrid IP-PBX is required. A PT with multiline display (e.g., KX-T7636 6-line display) is required for the
Hybrid IP-PBX system programming.
Note
For details about system programming using a PT, refer to "2.3.2 PT Programming" and "3.3 PT
Programming" in the Feature Guide.
Entering the System Programming Mode
PT (Administrator Level)
#
PROGRAM/
PAUSE
System Password for Administrator—
for PT Programming
Programming No.
= 1234
3 digits
PS (Using the KX-TD7680)
FUNC
Press POWER
for 2 seconds.
Select
"PS PROGRAM".
Select
"SYSTEM SET".
If required
System Lock Password
System Setting Menu
4 digits
PS (Using the KX-TD7690)
MENU
Press POWER
for 2 seconds.
S1
SEL
Select
"PS PROGRAM".
If required
SEL
Select
"SYSTEM SETTING".
S1
S1
ENTR
System Lock Password
4 digits
System Setting Menu
S1
Note
means default value throughout this section.
Installation Manual
191
2.9 Connection of 2.4 GHz Portable Stations
PS Registration
[690]
ENTER
PS No.
Extn. No.
001 to 128
1 to 4 digits
ENTER
To the PS
operation
below
END
When the PS has not been registered yet
When registering the PS for the first time, it is possible to select the desired language for the display.
(You do not need to enter the PS system programming mode when registering for the first time.)
Using the KX-TD7680
[ F2 ]
[ F3 ]
Press S2 repeatedly
to select the desired
language.
Press S3
for 2
seconds.
C.Tone
Press
POWER for
2 seconds.
Using the KX-TD7690
F2
F3
Press S2 repeatedly
to select the desired
language.
Press S3
for 2
seconds.
C.Tone
Press
POWER for
2 seconds.
When the PS has already been registered to another Hybrid IP-PBX
One PS can be registered to a maximum of 4 different Hybrid IP-PBXs.
Using the KX-TD7680
C.Tone
Choose
"SYSTEM 1–4".
Select
"REGISTRATION".
Using the KX-TD7690
SEL
Select
"REGISTRATION".
192
Installation Manual
S1
SEL
Choose
"SYSTEM 1–4".
C.Tone
S1
2.9 Connection of 2.4 GHz Portable Stations
Setting the System Lock
When a system lock has been set, the system lock password will be required for PS system setting.
Using the KX-TD7680
Choose
"Enable/Disable".
Select
"SYSTEM LOCK".
System Lock Password
System Lock Password
4 digits
4 digits
ENABLE
DISABLE
C.Tone
Using the KX-TD7690
Select
"SYSTEM LOCK".
SEL
SEL
CHNG
S1
S1
Choose
"Enable/Disable".
System Lock Password
ENTR
System Lock Password
ENABLE
S1
DISABLE
4 digits
S1
4 digits
ENTR
C.Tone
S1
Installation Manual
193
2.9 Connection of 2.4 GHz Portable Stations
Setting the Personal Identification Number (PIN) for PS Registration
To prevent registering the PS to a wrong Hybrid IP-PBX, a PIN for PS registration can be set to the Hybrid
IP-PBX. Before registering the PS to the Hybrid IP-PBX, register the PIN set to the Hybrid IP-PBX into the
PS. By doing so, the PS will only be registered to the Hybrid IP-PBX with the matching PIN.
Notes
•
By default, the PIN for PS registration is "1234" for both the Hybrid IP-PBX and PS. Therefore, the
PS can be registered to the Hybrid IP-PBX without setting the PIN.
•
The PIN for PS registration will only be used when registering the PS to the Hybrid IP-PBX.
Therefore, even when there is more than 1 Hybrid IP-PBX with the same PIN near the PS, the PS
will not be linked to a different Hybrid IP-PBX during normal operation after registration.
Setting the PIN for Hybrid IP-PBX
[692]
PIN for PS Registration
ENTER
1 to 4 digits
1234
ENTER
Setting the PIN for PS
Using the KX-TD7680
PIN for PS Registration
Select
"CHANGE PIN"
C.Tone
1 to 4 digits
1234
Using the KX-TD7690
SEL
Select
"CHANGE PIN"
194
Installation Manual
S1
PIN for PS Registration
1 to 4 digits
1234
ENTR
C.Tone
S1
END
2.9 Connection of 2.4 GHz Portable Stations
PS Termination
Confirm the following before cancelling the PS registration:
•
PS is turned on.
•
PS is within the range.
[691]
PS No.
001 to 128
ENTER
ENTER
If "Rejected" or "Time out" is displayed
CLEAR
Press "CLEAR".
YES
To the PS
operation
below
END
Press "YES".
If the registration information is still stored in the PS
Using the KX-TD7680
Select "YES".
Select the
desired item.
Select "DELETE
SYSTEM".
C.Tone
Using the KX-TD7690
SEL
Select "DELETE
SYSTEM".
S1
SEL
Select the
desired item.
S1
Select "YES".
SEL
C.Tone
S1
Testing the Operation
Walk around the service area while having a conversation using a registered PS. If noise is frequent or
conversations disconnect, relocate the CSs or install an additional CS.
Installation Manual
195
2.9 Connection of 2.4 GHz Portable Stations
2.9.8
Wall Mounting
1. Place the reference for wall mounting (on the following page) on the wall to mark the 2 screw positions.
2. Install the 2 screws and washers (included) into the wall.
Notes
•
•
Make sure that the screw heads are at the same distance from the wall.
Install the screws perpendicular to the wall.
3. Hook the CS on the screw heads.
196
Installation Manual
2.9 Connection of 2.4 GHz Portable Stations
Reference for Wall Mounting
Please copy this page and use as a reference for wall mounting.
Install a screw here.
71 mm
Install a screw here.
Note
Make sure to set the print size to correspond with the size of this page. If the dimension of the paper
output still deviates slightly from the measurement indicated here, use the measurement indicated
here.
Installation Manual
197
2.10 Connection of Doorphones, Door Openers, External Sensors, and External Relays
2.10 Connection of Doorphones, Door Openers,
External Sensors, and External Relays
2.10.1 Connection of Doorphones, Door Openers, External
Sensors, and External Relays
The KX-TDA100 supports a maximum of 8 doorphones (KX-T30865 with a DPH4 card, or German type with
a DPH2 card), 8 door openers, 8 external sensors, and 8 external relays.
The KX-TDA200 supports a maximum of 16 doorphones (KX-T30865 with a DPH4 card, or German type
with a DPH2 card), 16 door openers, 16 external sensors, and 16 external relays.
Notes
•
•
KX-T30865 is a Panasonic doorphone.
German type doorphones, door openers, external sensors, and external relays are user-supplied.
Maximum Cabling Distance
Cable
ø 0.4 mm:
ø 0.5 mm:
ø 0.6 mm:
CAT 5:
Maximum Distance
Under 70 m
Under 113 m
Under 180 m
Under 113 m
Doorphone
Door Opener
External Sensor/
External Relay Device
Installing the Doorphone (KX-T30865)
1. Loosen the screw to separate the doorphone into 2 halves.
Pan
ason
ic
Screw
198
Installation Manual
2.10 Connection of Doorphones, Door Openers, External Sensors, and External Relays
2. Pass the wires through the hole in the base cover, and attach the base cover to a wall using 2 screws.
Screw
To 8-pin terminal block
Note
Two kinds of screws are included with a KX-T30865. Please choose the appropriate kind for your wall
type.
: when a doorphone plate has been fixed to the wall
: when you wish to install the doorphone directly onto the wall
3. Connect the wires to the screws located in the front cover.
To 8-pin terminal block
4. Re-attach the 2 halves and re-insert the screw.
Connection
Use 8-pin and 10-pin terminal blocks (included with the card) for connection.
1. While pressing down on the hole at the top of the terminal block using a screwdriver, insert the wire into
the side hole as shown below. Repeat this procedure for other doorphones, door openers, external
sensors, and external relays.
Refer to "2.6.2 DPH4 Card", "2.6.3 DPH2 Card", and "2.6.4 EIO4 Card" for pin assignments.
Doorphone
Door Opener
External Sensor/
External Relay Device
Installation Manual
199
2.10 Connection of Doorphones, Door Openers, External Sensors, and External Relays
2. Attach the terminal blocks to the connectors of the DPH4/DPH2/EIO4 card on the Hybrid IP-PBX.
To doorphones/
door openers/
external sensors/
external relays
200
Installation Manual
2.11 Connection of Peripherals
2.11 Connection of Peripherals
2.11.1 Connection of Peripherals
Maximum Distance
Under 5 m
PC Server PC
BGM/
Music on Hold
Cable
ø 0.4 mm:
ø 0.5 mm:
ø 0.6 mm:
CAT 5:
Maximum Distance
Under 10 m
Under 10 m
Under 10 m
Under 10 m
Cable
ø 0.4 mm:
ø 0.5 mm:
ø 0.6 mm:
CAT 5:
Maximum Distance
Under 10 m
Under 10 m
Under 10 m
Under 10 m
USB
Pager:
Amplifier/Speaker
Maximum Distance
Under 2 m
PC
RS-232C
Printer
BGM/MOH
The Hybrid IP-PBX provides Background Music and Music on Hold. Up to 2 external music sources (e.g.,
user-supplied radios) can be connected to the Hybrid IP-PBX.
CAUTION
•
•
Wiring should be done carefully to prevent undue force being exerted on the plug. Otherwise,
music may intermittent.
External Music Jacks are SELV ports and should only be connected to approved SELV devices, or
in Australia, via the Line Isolation Unit with the Telecommunications Compliance Label.
Note
When the Hybrid IP-PBX and external music sources are not connected to the same earth, hum noise
may be induced into Background Music and Music on Hold.
Installation Manual
201
2.11 Connection of Peripherals
Pager
Up to 2 paging devices (user-supplied) can be connected to the Hybrid IP-PBX.
CAUTION
External Paging Jacks are SELV ports and should only be connected to approved SELV devices, or in
Australia, via the Line Isolation Unit with the Telecommunications Compliance Label.
PC/Printer (via RS-232C)
The Hybrid IP-PBX is equipped with an RS-232C interface. This interface provides communication between
the Hybrid IP-PBX and the user-supplied devices such as PC or line printers. The RS-232C port is used for
system programming, SMDR, diagnostics and external system database storage (save/load) functions.
Note
Use an RS-232C cross cable for connection between the Hybrid IP-PBX and PC.
Pin Assignments
Circuit Type
No.
6
9
1
5
Signal Name
Function
EIA
CCITT
2
RD (RXD)
Receive Data
BB
104
3
4
SD (TXD)
ER (DTR)
Transmit Data
Data Terminal Ready
BA
CD
103
108.2
5
6
SG
DR (DSR)
Signal Ground
Data Set Ready
AB
CC
102
107
7
8
RS (RTS)
CS (CTS)
Request To Send
Clear To Send
CA
CB
105
106
Connection Charts
For connecting a printer/PC with a 9-pin RS-232C connector
Hybrid IP-PBX
202
Printer/PC
Circuit Type
(EIA)
Signal
Name
Pin No.
Pin No.
Signal
Name
Circuit Type
(EIA)
BB
RD (RXD)
2
2
RD (RXD)
BB
BA
SD (TXD)
3
3
SD (TXD)
BA
CD
ER (DTR)
4
4
ER (DTR)
CD
AB
SG
5
5
SG
AB
CC
DR (DSR)
6
6
DR (DSR)
CC
CA
RS (RTS)
7
7
RS (RTS)
CA
CB
CS (CTS)
8
8
CS (CTS)
CB
Installation Manual
2.11 Connection of Peripherals
For connecting a printer/PC with a 25-pin RS-232C connector
Hybrid IP-PBX
Printer/PC
Circuit Type
(EIA)
Signal
Name
Pin No.
Pin No.
Signal
Name
Circuit Type
(EIA)
BB
RD (RXD)
2
1
FG
AA
BA
SD (TXD)
3
3
RD (RXD)
BB
CD
ER (DTR)
4
2
SD (TXD)
BA
AB
SG
5
20
ER (DTR)
CD
CC
DR (DSR)
6
7
SG
AB
CA
RS (RTS)
7
5
CS (CTS)
CB
CB
CS (CTS)
8
6
DR (DSR)
CC
4
RS (RTS)
CF
RS-232C Signals
•
Receive Data (RXD):…(input)
Conveys signals from the printer or the PC.
•
Transmit Data (TXD):…(output)
Conveys signals from the unit to the printer or the PC. A "Mark" condition is held unless data or
BREAK signals are being transmitted.
•
Data Terminal Ready (DTR):…(output)
This signal line is turned ON by the unit to indicate that it is ON LINE. Circuit ER (DTR) ON does
not indicate that communication has been established with the printer or the PC. It is switched OFF
when the unit is OFF LINE.
•
Signal Ground (SG)
Connects to the DC ground of the unit for all interface signals.
•
Data Set Ready (DSR):…(input)
An ON condition of circuit DR (DSR) indicates the printer or the PC is ready. Circuit DR (DSR) ON
does not indicate that communication has been established with the printer or the PC.
•
Request To Send (RTS):…(output)
This lead is held ON whenever DR (DSR) is ON.
•
Clear To Send (CTS):…(input)
An ON condition of circuit CS (CTS) indicates that the printer or the PC is ready to receive data
from the unit. The unit does not attempt to transfer data or receive data when circuit CS (CTS) is
OFF.
•
Frame Ground (FG)
Connects to the unit frame and the earth ground conductor of the AC power cord.
Installation Manual
203
2.11 Connection of Peripherals
PC/Server PC (via USB version 1.1)
The Hybrid IP-PBX is equipped with a USB interface. This interface provides communication between the
Hybrid IP-PBX and a PC or a Server PC.
The PC is used for system programming, diagnostics and external system database storage (save/load)
functions.
The Server PC is used for connecting PCs on a LAN to provide third party call control CTI. The CTI
connection uses the CSTA Phase 3 or TAPI 2.1 protocol.
Note
The operating system of the PC or Server PC required for third party call control depends on your CTI
application software. For details, refer to the manual for your CTI application software.
Pin Assignments
No.
204
Signal Name
3
2
1
VBUS
4
1
2
USB D-
3
USB D+
4
GND
Installation Manual
2.12 Power Failure Connections
2.12 Power Failure Connections
2.12.1 Power Failure Connections
When the power supply to the Hybrid IP-PBX fails, power failure transfer (PFT) will switch from the current
connection to the Power Failure Connection. Refer to "2.4.1 Power Failure Transfer" in the Feature Guide
for further information.
Power Failure Connection is required to implement this feature.
Note
While DC power is provided by the backup batteries, the Hybrid IP-PBX will remain fully operational and
the connection will not switch to the Power Failure Connection.
Using Analogue Trunk Card and Extension Card
Power Failure Connection connects a specific SLT and a trunk in the event of power failure. The following
analogue trunk and extension cards can be used for Power Failure Connections:
•
Analogue trunk cards: LCOT16 (4 PFT ports), LCOT8 (2 PFT port), and LCOT4 (2 PFT port)
•
Extension cards: MSLC16 (4 PFT ports), SLC16 (4 PFT ports), DHLC8 (2 PFT port) and SLC8
(2 PFT port)
To 1 analogue trunk card, connect only 1 extension card.
Note
By programming the Hybrid IP-PBX, a trunk conversation established during power failure can be
maintained even when the power returns and the connection is switched back to the normal
configuration from the Power Failure Connection. However, if no special programming is performed, the
connection will be dropped when power returns.
RJ11
R2
R1
T1
T2
T2
T1
R1
R2
Extension Card
(e.g., SLC8)
Trunk Card
(e.g., LCOT8)
To trunk
To SLT
Accessory and User-supplied Items
Accessory (included): none
User-supplied (not included): RJ11 connectors
Installation Manual
205
2.12 Power Failure Connections
RJ11 Connector Pin Assignments for Analogue Trunk Card
PFT Ports 1 and 2
1
4
No.
Signal Name
Function
1
R2
Ring port 2
2
R1
Ring port 1
3
T1
Tip port 1
4
T2
Tip port 2
PFT Ports 3 and 4 (for LCOT16 card only)
1
4
No.
Signal Name
Function
1
R4
Ring port 4
2
R3
Ring port 3
3
T3
Tip port 3
4
T4
Tip port 4
RJ11 Connector Pin Assignments for Extension Card
PFT Ports 1 and 2
1
4
No.
Signal Name
Function
1
T2
Tip port 2
2
T1
Tip port 1
3
R1
Ring port 1
4
R2
Ring port 2
PFT Ports 3 and 4 (for MSLC16/SLC16 card only)
1
4
206
Installation Manual
No.
Signal Name
Function
1
T4
Tip port 4
2
T3
Tip port 3
3
R3
Ring port 3
4
R4
Ring port 4
2.12 Power Failure Connections
Using BRI Card
LINE 1 and LINE 2 of the BRI4 and BRI8 cards can be used for Power Failure Connections.
Note
When the power returns, the connection will switch back to normal configuration from the Power Failure
Connection, and a trunk conversation established during power failure will be dropped.
RJ45
(LINE 2)
Set all DIP switches
at "ON" positions.
To ISDN extension
To NT1
RJ45
(LINE 1)
OFF
OFF
ON
ON
Accessory and User-supplied Items
Accessory (included): none
User-supplied (not included): RJ45 connectors
Switch Settings
Switch
Type
Usage and Status Definition
PFT Setting
DIP
Set all DIP switches to "ON" positions to use LINE 1 and LINE 2 as a
PFT port.
LINE 1: Power Failure LINE (NT1)
LINE 2: Power Failure EXTN (extension)
RJ45 Connector LINE 1 Pin Assignments
8
1
No.
Signal Name
Level [V]
Function
1-2
Reserved
–
–
3
TX1
(+)
Transmit data 1
4
RX2
(+)
Receive data 2
5
RX1
(-)
Receive data 1
6
TX2
(-)
Transmit data 2
7-8
Reserved
–
–
Installation Manual
207
2.12 Power Failure Connections
RJ45 Connector LINE 2 Pin Assignments
8
1
208
Installation Manual
No.
Signal Name
Level [V]
Function
1-2
Reserved
–
–
3
RX2
(+)
Receive data 2
4
TX1
(+)
Transmit data 1
5
TX2
(-)
Transmit data 2
6
RX1
(-)
Receive data 1
7-8
Reserved
–
–
2.13 Starting the Hybrid IP-PBX
2.13 Starting the Hybrid IP-PBX
2.13.1 Starting the Hybrid IP-PBX
CAUTION
•
•
•
•
•
SD Memory Card must be inserted in the SD Memory Card slot of the MPR card before start up.
Before touching the System Initialise Switch, discharge static electricity by touching ground or
wearing an earthing strap.
Once you have started the Hybrid IP-PBX and if you unplug the Hybrid IP-PBX, do not perform the
following procedures to start the Hybrid IP-PBX again. Otherwise, your programmed data is
cleared. To restart the Hybrid IP-PBX, refer to "4.1.4 Using the Reset Button".
The Hybrid IP-PBX will continue to be powered even if the power switch is turned "OFF".
The power supply cord is used as the main disconnect device, ensure that the socket-outlet is
located/installed near the equipment and is easily accessible.
1. Set the System Initialise Switch to the "SYSTEM INITIALIZE" position.
RUN Indicator
Reset Button
RESET
SYSTEM
INITIALIZE
NORMAL
System Initialise Switch
Installation Manual
209
2.13 Starting the Hybrid IP-PBX
2. Plug the AC power cord into the Hybrid IP-PBX and an AC outlet, and turn on the Hybrid IP-PBX. The
RUN indicator will flash.
Note
For safety reasons, do not stretch, bend, or pinch the AC power cord.
To AC Outlet
3. While the RUN indicator is flashing, return the System Initialise Switch to the "NORMAL" position.
Depending on the configuration, initialisation takes about 1 min to 3 min. If successfully executed, the
RUN indicator will stop flashing and be kept lit.
All data will be cleared, and the Hybrid IP-PBX as well as all optional service cards (except for the IP-GW
card) will be initialised to the default values. The DPTs should show the time as 01:00.
The data of the IP-GW card will not be initialised.
Notes
•
•
Use only the AC power cord included with the Hybrid IP-PBX for the PSU.
Use only the supplied AC power cord for the purpose of applying the EMC standard, if the Hybrid
IP-PBX is connected (Germany only).
LED Indications
Indication
Colour
Description
RUN
Green
PBX status indication
•
OFF: Power Off (includes normal reset)
•
ON: Power On and running (on-line)
•
Flashing (60 times per minute): Starting up
•
Flashing (120 times per minute): Starting up or resetting with:
•
the System Initialise Switch in "SYSTEM INITIALIZE"
position
•
the SD Memory Card not inserted
ALARM
Red
Alarm indication
•
OFF: Normal
•
ON: Alarm (CPU stop, alarm for each card)
•
Flashing: Alarm (MPR file error in restarting)
Confirming the Trunk Connection
After initialisation, programme the Hybrid IP-PBX and establish trunk connection, and then use a PT to
confirm it.
210
Installation Manual
2.13 Starting the Hybrid IP-PBX
To confirm, dial [ ] [3] [7] + trunk number (3 digits) or press S-CO button. You will hear a dial tone if the trunk
is available and connected.
Installation Manual
211
2.13 Starting the Hybrid IP-PBX
212
Installation Manual
Section 3
Guide for the KX-TDA Maintenance Console
Explains the installation procedure, structure, and basic
information of the KX-TDA Maintenance Console.
Installation Manual
213
3.1 Overview
3.1
Overview
3.1.1
Overview
KX-TDA Maintenance Console is designed to serve as an overall system programming reference for the
Hybrid IP-PBX. To programme and administer the Hybrid IP-PBX by PC, you need to install the KX-TDA
Maintenance Console onto the PC.
This section describes overview and installation of the KX-TDA Maintenance Console only.
KX-TDA Maintenance Console*1
Menu Bar
Programme Menu
*1
The contents and design of the software are subject to change without notice.
214
Installation Manual
3.2 Connection
3.2
Connection
3.2.1
Connection
Serial Interface Connection
USB Port
To USB Port
PC
To COM Port
PC
RS-232C Port
Note
For pin assignments and maximum cabling distance, refer to "2.11.1 Connection of Peripherals".
LAN Connection via CTI-LINK Card
RJ45
Switching Hub
To network port
PC
Note
For pin assignments and maximum cabling distance, refer to "2.6.7 CTI-LINK Card".
Installation Manual
215
3.2 Connection
External Modem Connection
Modem
To RS-232C port (25-pin)
To trunk/Hybrid IP-PBX extension
port assigned as the trunk destination
External Modem
RS-232C Port
(9-pin)
Hybrid IP-PBX
Signal Name
Pin No.
Pin No.
Signal Name
SD (TXD)
2
2
RD (RXD)
RD (RXD)
3
3
SD (TXD)
DR (DSR)
6
4
ER (DTR)
ER (DTR)
20
6
DR (DSR)
After connecting the Hybrid IP-PBX and the external modem, set the power switch of the external modem
to "ON", then the external modem will be initialised with the default values.
The following AT command settings may be required for the modem:
•
The Data Terminal Ready (DTR) signal should be ignored.
•
The Data Terminal Equipment (DTE)/Modem flow control should be turned off.
•
The data compression should be disabled.
•
Error Correction is not necessary.
Notes
•
•
•
216
Use an RS-232C straight cable for connection between the Hybrid IP-PBX and external modem.
An AT command (for initialisation, enabling automatic answer, etc.) can only be programmed by
KX-TDA Maintenance Console. "AT&F0Q0E0V1S0=1X0&D0" is stored as the default value.
For more information about the AT command, refer to the external modem's instructions.
Installation Manual
3.3 Installation of the KX-TDA Maintenance Console
3.3
Installation of the KX-TDA Maintenance
Console
3.3.1
Installing and Starting the KX-TDA Maintenance Console
System Requirements
Operating System
•
Microsoft® Windows® 98 SE, Windows Me, Windows 2000, or Windows XP
Hardware
•
•
•
CPU: Intel® Pentium® 133 MHz or better microprocessor
RAM: at least 64 megabytes (MB) of free RAM (128 MB recommended)
HDD: at least 100 MB of hard disc space
Password Security
Warning to the Administrator or Installer regarding the system password
1. Please provide all system passwords to the customer.
2. To avoid unauthorised access and possible abuse of the PBX, keep the passwords secret, and
inform the customer of the importance of the passwords, and the possible dangers if they become
known to others.
3. The PBX has default passwords preset. For security, change these passwords the first time that
you programme the PBX.
4. Change the passwords periodically.
5. It is strongly recommended that passwords of 10 numbers or characters be used for maximum
protection against unauthorised access. For a list of numbers and characters that can be used in
system passwords, refer to "3.1.3 Entering Characters" in the Feature Guide.
6. If a system password is forgotten, it can be found by loading a backup of the system data into a
PC, and checking the password using the KX-TDA Maintenance Console software. If you do not
have a backup of the system data, you must reset the PBX to its factory defaults and reprogramme
it. Therefore, we strongly recommend maintaining a backup of the system data. For more
information on how to back up the system data, refer to the on-line help of the Maintenance
Console.
However, as system passwords can be extracted from backup copies of the system data file, do
not allow unauthorised access to these files.
Installation Manual
217
3.3 Installation of the KX-TDA Maintenance Console
Installing the KX-TDA Maintenance Console
Notes
•
•
•
Make sure to install and use the KX-TDA Maintenance Console for version 2.0.
To install or uninstall the software into Windows 2000 Professional or Windows XP Professional,
the user must be grouped either of "Administrators" or "Power Users".
To connect the PC to the Hybrid IP-PBX via USB, the KX-TDA USB driver must have been
installed. Follow the instructions of the wizard to install the KX-TDA USB driver.
1. Save the setup file of the KX-TDA Maintenance Console
on your PC.
2. Double-click the icon to execute the setup file.
3. Follow the instructions of the wizard.
Starting the KX-TDA Maintenance Console and Assigning the Basic
Items (Quick Setup)
When you start the KX-TDA Maintenance Console with the Installer Level Programmer Code and connect
to the Hybrid IP-PBX for the first time after initialisation (with the factory default setting), Quick Setup will
launch automatically. During Quick Setup, you will setup the following basic items:
•
Date and Time of the Hybrid IP-PBX. The date and time set on the PC will be used.
•
System Password for installer for PC programming.
•
Operator extension numbers. Operator extensions for all time modes (day/lunch/break/night) can
be assigned.
•
•
•
218
Flexible Numbering type to pattern 1 or pattern 2. If pattern 1 (with ) is selected, " " must prefix
all feature numbers (except access numbers) when an extension user wants to use a feature.
Operator call and Idle Line Access/ARS numbers (0 or 9). The feature numbers for operator call
and Idle Line Access/ARS can be selected.
Remote Maintenance Dial Number. Enter the complete telephone number of the PBX (including
the country code). When necessary, this number will be used to access the PBX from a remote
location for maintenance purposes.
Installation Manual
3.3 Installation of the KX-TDA Maintenance Console
1. Connect the PC to the Hybrid IP-PBX with a USB cable.
2. Start the KX-TDA Maintenance Console from the Start
menu.
3. Type the Installer Level Programmer Code (default: 1234),
then click [OK].
The Programmer Code authorises different programming
levels, and the Quick Setup is only available when you start
the KX-TDA Maintenance Console with the Installer Level
Programmer Code.
Note
There are 2 other Programmer Codes with limited
authorisation: Administrator Level (default: 1111), and
User Level (default: none).
4. Click "Connect"
"USB" from the menu bar.
5. Type the system password for installer (default: 1234), then
click [OK] to log-in.
6. When country/area data do not match:
a. Click [OK] to replace the country/area data of the
Hybrid IP-PBX. Replacement may take several
minutes to complete.
b. Follow the procedure described in "2.13.1 Starting the
Hybrid IP-PBX" and restart the Hybrid IP-PBX.
c. Repeat steps 2 to 5 to restart the KX-TDA
Maintenance Console.
Installation Manual
219
3.3 Installation of the KX-TDA Maintenance Console
7. Follow the instructions of the wizard and assign the basic
items (Quick Setup).
The programme menu appears.
Notice
1. During a long programming session, it is highly recommended that you periodically save the
system data to the SD Memory Card. You can think of system data as stored in RAM, whereas SD
Memory Card as stored on a hard disk. If the PBX undergoes a sudden power failure or system
reset for some reason, all the system data in RAM will be lost.
To save the system data to the SD Memory Card, (1) click the "SD Memory Backup" icon before
resetting the PBX or turning off the power, or (2) exit the KX-TDA Maintenance Console so that the
PBX starts automatically saving the system data.
2. When the PBX is initialised, not all data is taken from the SD Memory Card. The data for present
status of extension FWD/DND buttons is taken from battery backup memory in the PBX.
3. The PC will not perform any shutdown operation, or enter the power-saving system standby mode
while the KX-TDA Maintenance Console is connected to the Hybrid IP-PBX. To perform either of
the operations above, first close the connection to the Hybrid IP-PBX.
CAUTION
Do not remove the SD Memory Card while power is supplied to the Hybrid IP-PBX. Doing so may cause
the Hybrid IP-PBX to fail to start when you try to restart the system.
220
Installation Manual
Section 4
Troubleshooting
This section provides information on the Hybrid IP-PBX and
telephone troubleshooting.
Installation Manual
221
4.1 Troubleshooting
4.1
Troubleshooting
4.1.1
Installation
PROBLEM
Extension does not operate.
PROBABLE CAUSE
SOLUTION
Bad extension card.
•
Exchange the card for a known working
one.
Bad connection between the
Hybrid IP-PBX and telephone.
•
Take the telephone and plug it into the
same extension port using a short
telephone cord. If the telephone works,
then the connection between the Hybrid
IP-PBX and the telephone must be
repaired.
A telephone with an A-A1 relay
is connected.
•
•
Use a 2-wire cord.
Set the A-A1 relay switch of the
telephone to the "OUT" or "OFF"
position.
Bad telephone.
•
Take the telephone and plug it into
another extension port that is working.
If the telephone does not work, replace
the telephone.
Wrong type of PSU.
•
Replace the PSU with the appropriate
type.
•
Press the Reset Button (refer to "4.1.4
Using the Reset Button").
Turn off the power switch, and then turn
it back on.
Turn off the power switch, and then
unplug the Hybrid IP-PBX. After 5
minutes, plug the Hybrid IP-PBX back
in, and turn the power switch back on.
The Hybrid IP-PBX does not
operate properly.
•
•
Noise on external paging.
Induced noise on the wire
•
between the Hybrid IP-PBX and
the amplifier.
Use a shielded cable as the connection
wire between the Hybrid IP-PBX and
amplifier. A short shielded cable is
recommended.
Distorted external music.
Excessive input level from
external music source.
Decrease the output level of the
external music source by using the
volume control on the music source.
•
Voice-calling mode and Hands- •
Alternate Calling—Ring/Voice
free mode with LCS are not
and Live Call Screening (LCS)
•
do not function as set when using available with Wireless Phones.
a Wireless Phone (KX-T7880/
KX-T7885/KX-TD7894/KXTD7895).
222
Installation Manual
Switch the calling mode to ring-calling.
Set the LCS mode to "Private".
4.1 Troubleshooting
PROBLEM
PROBABLE CAUSE
The ALARM indicator on the
A major system error occurs in
front of the cabinet turns on red. the Hybrid IP-PBX.
SOLUTION
•
See the error log using the KX-TDA
Maintenance Console (refer to "4.1.5
Troubleshooting by Error Log").
Installation Manual
223
4.1 Troubleshooting
4.1.2
Connection
Connection between the Hybrid IP-PBX and a PT:
Can you dial
an extension?
CAUSE
No
SOLUTION
The T/R is connected to the D1/D2.
D1
T
R
D2
D1
T
R
D2
Hybrid IP-PBX
Use the correct cord (the
inner 2 wires are for T/R and
the outer 2 wires are for
D1/D2).
Extension
Connection between the Hybrid IP-PBX and an SLT:
CAUSE
SOLUTION
The T/R is connected to the D1/D2.
D1
T
R
D2
T
R
Hybrid IP-PBX
Yes
Extension
Connection between the Hybrid IP-PBX and an SLT that is polarity-sensitive:
CAUSE
SOLUTION
The "T" is connected to the "R".
D1
T
R
D2
Hybrid IP-PBX
(Continued on the next page.)
224
Installation Manual
Use the correct cord (the
inner 2 wires are for T/R).
• If a telephone equipped
with an A-A1 relay is
connected to the Hybrid
IP-PBX, set the A-A1
relay switch of the
telephone to "OFF".
T
R
Extension
Reverse the connections of
the T/R.
4.1 Troubleshooting
Connection between the trunk and the Hybrid IP-PBX:
(Continued from the
previous page.)
Can you dial
out on a
trunk?
CAUSE
Trunk is connected to the T2/T1.
T2
R1
T1
R2
No
Trunk
SOLUTION
Reconnect the trunk to
the T1/R1 or T2/R2 of the
telephone jack using
2-conductor wiring.
Hybrid IP-PBX
Trunk is connected to the T2/R1.
T2
R1
T1
R2
Trunk
Hybrid IP-PBX
Installation Manual
225
4.1 Troubleshooting
4.1.3
Operation
PROBLEM
PROBABLE CAUSE
•
SOLUTION
•
When using the
speakerphone on an APT,
nothing is audible.
•
•
When using the
speakerphone/monitor
mode with a DPT, nothing is
audible.
The "HEADSET" mode is
selected by Personal
Programming, "Handset/
Headset Selection".
•
When the headset is not used, select
the "HANDSET" mode by Personal
Programming.
•
The PT does not ring.
•
The ringer volume is off.
•
Turn on the ringer volume.
•
During a power failure,
extensions connected to
ports 1 to 4 of MSLC16/
SLC16 and ports 1 to 2 of
DHLC8/SLC8 cards do not
operate.
•
A DPT or APT is connected •
to the extension port.
The dialling mode (tone or •
pulse) is incorrect.
Disconnect the DPT or APT and
connect an SLT.
Set the Tone/Pulse switch to the other
position.
•
Originating an outside call,
call transfer, or conference
cannot be performed.
•
The corresponding CO
•
button does not exist on the
PT.
Programme the CO button. Refer to
"1.19.2 Flexible Buttons" in the Feature
Guide.
•
Cannot register the PS.
•
Wrong Personal
•
Identification Number (PIN)
is registered to the PS.
Register the PIN set to the Hybrid IPPBX into the PS.
•
CS is not connected
properly.
•
Make sure that the cable is connected
properly with correct pin assignments.
Also, make sure that the cable does not
make short circuits.
Switch all DIP switches off.
CSIF card is not working.
•
Install the CSIF card properly.
CS is not working.
•
Make sure that the cable is connected
properly with correct pin assignments.
Also, make sure that the cable does not
make short circuits.
Switch all DIP switches off.
•
•
PS becomes out of range.
•
•
Cannot make calls using the •
PS.
The HANDSET/HEADSET •
selector is set to the
"HEADSET" position.
•
•
•
•
226
•
Location of CS is not good. •
Locate the CS properly (refer to "2.8.5
Site Survey Using the KX-TCA255/KXTD7590" or "2.9.5 Site Survey" ).
•
Access system of the PS is •
not properly set.
Change the access system setting of
the PS to the appropriate system or
automatic.
Noise is frequent while using •
the PS.
•
Conversations disconnect
while using the PS.
Installation Manual
When the headset is not used, set the
HANDSET/HEADSET selector to the
"HANDSET" position.
Call handover is not
working.
PS is out of CS coverage
area.
•
Locate the CS properly (refer to "2.8.5
Site Survey Using the KX-TCA255/KXTD7590" or "2.9.5 Site Survey" ).
4.1 Troubleshooting
PROBLEM
•
PS stays out of service
when the CS status is
changed from Out of
Service to In Service.
PROBABLE CAUSE
•
•
It may take about 20 s for
CS to start up after the
status has been changed to
In Service.
SOLUTION
Wait until the CS starts up.
Installation Manual
227
4.1 Troubleshooting
4.1.4
Using the Reset Button
If the Hybrid IP-PBX does not operate properly, use the Reset Button. Before using the Reset Button, try
the system feature again to confirm whether there definitely is a problem or not.
CAUTION
In order to avoid possible corruption of data on the SD Memory Card, please ensure that the "SD
ACCESS" LED is off before pressing the Reset Button.
Notes
•
•
When the System Initialise Switch is set to "NORMAL", pressing the Reset Button causes the
following:
– Camp-on is cleared.
– Calls on hold are terminated.
– Calls on exclusive hold are terminated.
– Calls in progress are terminated.
– Call park is cleared.
Other data stored in memory, except the above, are not cleared.
When the Reset Button is pressed with the System Initialise Switch in the "SYSTEM INITIALIZE"
position, all data stored in memory are cleared.
Operation
If the Hybrid IP-PBX does not operate properly:
1. Set the System Initialise Switch to the "NORMAL" position.
2. Press the Reset Button.
RUN Indicator
BATT
ALARM
SD
ACCESS
LED
Reset Button
RESET
SYSTEM
INITIALIZE
NORMAL
System Initialise Switch
228
Installation Manual
4.1 Troubleshooting
4.1.5
Troubleshooting by Error Log
When a major system error occurs in the Hybrid IP-PBX, the ALARM indicator on the front of the cabinet
turns on red, and the system logs the error information.
Error Log Display Format
Below is the display format of the error log. To see the error log using the KX-TDA Maintenance Console,
refer to the on-line help of the KX-TDA Maintenance Console.
Example: KX-TDA Maintenance Console
3
1
2
4
5
6
Example: Station Message Detail Recording (SMDR)
04/01/01 10:37AM MJ ALM #000 10000 MPR WDT overflow
04/01/01 11:07AM MN ALM #010 10000 AC power down
04/01/01 03:55PM MN ALM #301 10501 Digital trunk RAI reception
1
2
3
4
5
6
Description
Item
Description
1
Date
Date of the error detection
2
Time
Time of the error detection
3
Level
Major Alarm (MJ ALM):
Errors that affect the whole system operation, or result in system
failure
Minor Alarm (MN ALM):
Errors that affect certain part of system operation
4
Error Code
Three-digit error code
Installation Manual
229
4.1 Troubleshooting
Item
5
Sub Code
Description
Five-digit sub code (1XXYY)
1: Cabinet number
XX: Slot number
KX-TDA100: 00 to 06 (00: MPR slot; 01 to 05: Free slot; 06: Option
slot)
KX-TDA200: 00 to 11 (00: MPR slot; 01 to 10: Free slot; 11: Option
slot)
YY: Physical port number (01 to 16)
For OPB3 card, sub slot number + port number will be displayed.
Sub slot 1: 11 to 14
Sub slot 2: 21 to 24
Sub slot 3: 31 to 34
Note
When there is no parameter for slot and physical port number, XX
and YY will be displayed as "00".
Example: Sub code for MPR card = 10000
6
230
Error Message
Installation Manual
Error description
4.1 Troubleshooting
List of Errors and Solutions
The tables below list the errors and their solutions.
When an error whose error code is indicated with "*" occurs in the Hybrid IP-PBX, the ALARM indicator on
the front of the cabinet turns on red, and the system logs the error information.
When the error conditions indicated by the error codes "021", "091", "092", "230", and "510" are recovered,
the ALARM indicator will turn off automatically, indicating successful troubleshooting. When other errors are
logged, the ALARM indicator will turn off only when the log for major or minor errors is cleared from the KXTDA Maintenance Console.
In other words, the ALARM indicator will turn off under the following conditions:
•
When the errors "021", "091", "092", "230", and "510" are logged: when the error conditions
are recovered
•
When other errors are logged: when the log for major or minor errors is cleared from the KX-TDA
Maintenance Console
LPR (Optional Service Card with Local Processor) Initial Self Diagnosis
Error Code
211
Error Message
Speech path
loop-back check
error
PROBABLE CAUSE
•
Optional service card
malfunction: DHLC, DLC,
SLC, CSIF, LCOT, T1, E1,
BRI, PRI, OPB3, E&M, IPGW, DID
212
Echo canceller
access error
•
Optional service card
malfunction: CSIF, ECHO
214
DSP Boot check
error
•
Optional service card
malfunction: T1, E1
215
Framer IC access •
error
Optional service card
malfunction: T1, E1, BRI, PRI
216
MSG card DSP
error
•
Optional service card
malfunction: MSG, OPB3
217
MSG card data
error
•
Optional service card
malfunction: MSG, OPB3
Erroneous recording of
messages
•
SOLUTION
•
•
•
•
•
•
•
•
•
See if the corresponding optional
service card is installed properly
Pull out and re-insert the
corresponding optional service card
Press the Reset Button
Replace the corresponding optional
service card
See if the corresponding optional
service card is installed properly
Pull out and re-insert the
corresponding optional service card
Press the Reset Button
Re-record the messages
Replace the corresponding optional
service card
Installation Manual
231
4.1 Troubleshooting
System Start-up and On-line Operation
Error Code
Error Message
000*
MPR WDT overflow
001
SDRAM bit error
PROBABLE CAUSE
•
•
•
•
002
System Restart
•
•
•
•
•
010*
AC power down
•
•
•
SOLUTION
MPR card malfunction
Optional service card
malfunction: CTI-LINK
Erroneous processing of
MPR card software
Software error due to
external factors
•
•
•
Press the Reset Button
Reprogramme the Hybrid IP-PBX
Replace the MPR card (be sure to turn
off the Hybrid IP-PBX when replacing)
Reset Button is pressed
Power failure
MPR card malfunction
Erroneous processing of
MPR card software
Software error due to
external factors
•
•
•
•
Ignore if not frequent
Press the Reset Button
Reprogramme the Hybrid IP-PBX
Replace the MPR card (be sure to turn
off the Hybrid IP-PBX when replacing)
Power supply system
malfunction (e.g., power
failure, power noise,
trouble with UPS)
Bad connection or
breaking of AC cord
Power supply circuit (PSU,
back board) malfunction
•
•
Check the power supply system
See if the AC cord is connected
properly
Check the AC cord
Replace the AC cord (be sure to turn
off the Hybrid IP-PBX when replacing)
Replace the PSU (be sure to turn off
the Hybrid IP-PBX when replacing)
Replace the back board (be sure to
turn off the Hybrid IP-PBX when
replacing)
•
•
•
•
011*
DC power down
•
•
•
AC power down
Power supply circuit (PSU,
back board) malfunction
Detection of over current
(short circuit on optional
service cards)
•
•
•
•
•
•
•
Check the power supply system
See if the AC cord is connected
properly
Check the AC cord
Replace the AC cord (be sure to turn
off the Hybrid IP-PBX when replacing)
Replace the PSU (be sure to turn off
the Hybrid IP-PBX when replacing)
Replace the back board (be sure to
turn off the Hybrid IP-PBX when
replacing)
Remove the optional service cards and
restart the Hybrid IP-PBX
012*
MPR RAM battery
low
•
•
Battery out
MPR card malfunction
•
Replace the MPR card (be sure to turn
off the Hybrid IP-PBX when replacing)
014*
FAN Alarm
•
PSU-L malfunction
•
•
See if anything is jammed in the fan
Replace the PSU (be sure to turn off
the Hybrid IP-PBX when replacing)
232
Installation Manual
4.1 Troubleshooting
Error Code
Error Message
PROBABLE CAUSE
SOLUTION
016
CS overload
•
•
•
Defective cable
CS malfunction
Optional service card
malfunction: CSIF
•
•
•
Check the cable diameter and length
Replace the CS
Replace the corresponding optional
service card
017
BRI port overload
•
•
Defective cable
Defective ISDN terminal
equipment
Optional service card
malfunction: BRI
•
•
Check the cable
Replace the defective terminal
equipment
Check the number of connected
terminal equipment
Replace the corresponding optional
service card
•
•
•
020*
SD file access error
•
•
•
021*
SD Memory Card
disconnected
•
•
•
•
022
Not enough free
space on SD card
•
SD Memory Card
malfunction
Bad connection of SD
Memory Card
MPR card malfunction
•
•
•
•
Press the Reset Button
Reprogramme the Hybrid IP-PBX
Replace the SD Memory Card
Replace the MPR card (be sure to turn
off the Hybrid IP-PBX when replacing)
•
Not enough memory
space available to save
the system data, or to
•
upload system files from
the KX-TDA Maintenance
Console
Delete the files whose file names start
with "$" from SD Memory Card
Delete the "Pxxx" files (old programme
files of optional service cards) from SD
Memory Card. "xxx" indicates the card
type (e.g., "PDHLC" for DHLC card)
SD Memory Card not
installed
Bad connection of SD
Memory Card
SD Memory Card
malfunction
MPR card malfunction
Note
Do not delete the "PMPR" file; it is the
programme file of the MPR card.
Installation Manual
233
4.1 Troubleshooting
Error Code
Error Message
PROBABLE CAUSE
023
System data file
version error
•
024
System initialization
file version error
•
025
Card initialization file
version error
026
LCD file version error
027
System data file
checksum error
028
System initialization
file checksum error
029
Card initialization file
checksum error
030
LCD file checksum
error
031*
System data file not
found
•
032*
System initialization
file not found
•
033*
Card initialization file
not found
034*
LCD file not found
035
System data file
access error
036*
System initialization
file access error
037*
Card initialization file
access error
038*
LCD file access error
039*
SD file access error
090
SOLUTION
Old system files on SD
Memory Card
Defective system files on
SD Memory Card
•
•
Restore the backup files
Re-install the software
SD Memory Card not
installed
Bad connection of SD
Memory Card
SD Memory Card
malfunction
MPR card malfunction
•
•
•
•
Press the Reset Button
Reprogramme the Hybrid IP-PBX
Replace the SD Memory Card
Replace the MPR card (be sure to turn
off the Hybrid IP-PBX when replacing)
Over Card Limitation •
Too many optional service •
cards installed
Reduce the number of optional service
cards
091*
PT connection over
•
Too many PTs connected •
Reduce the number of PTs
092*
CS connection over
•
Too many CSs connected •
Reduce the number of CSs
200
LPR start up error
(ROM NG)
•
201*
LPR start up error
(RAM NG)
Optional service card
malfunction: DHLC, DLC,
CSIF, T1, E1, BRI, PRI,
OPB3, CTI-LINK, E&M,
IP-GW, DID, SLC8
234
Installation Manual
•
•
•
•
•
Pull out and re-insert the
corresponding optional service card
Press the Reset Button
Replace the corresponding optional
service card
4.1 Troubleshooting
Error Code
Error Message
202*
LPR start up error
(No Program)
203*
LPR start up error
(Version NG)
204*
LPR start up error
(Download NG)
205*
LPR start up error
(No response)
206
LPR start up error
(Card type NG)
207
LPR start up error
(Check SUM NG)
230*
Card disconnected
PROBABLE CAUSE
•
Optional service card
malfunction: DHLC, DLC,
CSIF, T1, E1, BRI, PRI,
OPB3, CTI-LINK, E&M,
IP-GW, DID, SLC8
SOLUTION
•
•
•
•
•
•
•
Optional service card not
installed properly
Optional service card
malfunction
Back board malfunction
•
•
•
•
•
231
LPR alive check error •
232
MPR-LPR
communication error
233
LPR data check error
234
DPLL clock failure
•
•
Optional service card
malfunction: DHLC, DLC,
CSIF, T1, E1, BRI, PRI,
OPB3, CTI-LINK, E&M,
IP-GW, DID, SLC8
Back board malfunction
MPR card malfunction
•
•
•
•
•
•
Pull out and re-insert the
corresponding optional service card
Press the Reset Button
Update the software of the
corresponding optional service card
Replace the corresponding optional
service card
See if the corresponding optional
service card is installed properly
Pull out and re-insert the
corresponding optional service card
Press the Reset Button
Replace the corresponding optional
service card
Replace the back board (be sure to
turn off the Hybrid IP-PBX when
replacing)
See if the corresponding optional
service card is installed properly
Pull out and re-insert the
corresponding optional service card
Press the Reset Button
Replace the corresponding optional
service card
Replace the back board (be sure to
turn off the Hybrid IP-PBX when
replacing)
Replace the MPR card (be sure to turn
off the Hybrid IP-PBX when replacing)
235*
CS clock failure
•
Optional service card
malfunction: CSIF
•
Replace the corresponding optional
service card
250*
T1/E1 DSP failure
•
Optional service card
malfunction: T1, E1
•
251
MSG DSP failure
•
Optional service card
malfunction: MSG
•
See if the corresponding optional
service card is installed properly
Replace the corresponding optional
service card
Installation Manual
235
4.1 Troubleshooting
Error Code
Error Message
PROBABLE CAUSE
300*
Digital trunk out of
synchronization
•
301*
Digital trunk RAI
reception
•
302*
Digital trunk AIS
reception
303*
Multiframe out of
synchronization
304*
Frame error
•
•
Network (digital trunk)
malfunction
Optional service card
malfunction: PRI, T1, E1
Wrong A/B switch setting:
PRI, T1, E1
Wrong termination switch
setting: PRI30, E1
SOLUTION
•
•
•
•
•
•
305*
Data Link failure
•
•
•
306
E1 Channel Block
failure
•
•
•
•
Check the signals from the network
Check the cable
See if the A/B switch is set to A on the
corresponding optional service card
See if the termination switch is set
properly on the corresponding optional
service card: 120 Ω when using RJ45
connector; 75 Ω when using BNC
connector
See if the corresponding optional
service card is installed properly
Replace the corresponding optional
service card
Data link between the CS •
and CSIF card or DHLC/
DLC card failed
•
Data link between the
network and PRI/BRI card •
failed
Data link between the
network and IP-GW card
failed
Check the connection between the CS
and CSIF card or DHLC/DLC card
Check the connection between the
network and PRI/BRI card
Check the connection between the
network and IP-GW card
•
•
•
Check the signals from the network
Check the cable
See if the A/B switch is set to A on the
corresponding optional service card
See if the termination switch is set
properly on the corresponding optional
service card: 120 Ω when using RJ45
connector; 75 Ω when using BNC
connector
See if the corresponding optional
service card is installed properly
Replace the corresponding optional
service card
Network (digital trunk)
malfunction
Optional service card
malfunction: E1
Wrong A/B switch setting:
E1
Wrong termination switch
setting: E1
•
•
•
307
LAN No Carrier
•
IP-GW card not connected •
to the LAN
Check the connection between the
LAN and IP-GW card
308
IP-GW LAN Loop
back Error
•
Detection of IP-GW LAN
Loop back Test error
Replace the corresponding optional
service card
Collect the log data of IP-GW (refer to
the documentation for the IP-GW card)
•
•
309
236
IP-GW Core Data
Link Error
Installation Manual
•
Detection of IP-GW Core
data Link error
•
•
Press the Reset Button
Collect the log data of IP-GW (refer to
the documentation for the IP-GW card)
4.1 Troubleshooting
Error Code
310*
Error Message
Port Link Failure
PROBABLE CAUSE
•
•
SOLUTION
Voice Processing System •
malfunction
•
Ports defective on optional
service card: DHLC, DLC •
Check the Voice Processing System
See if the corresponding optional
service card is installed properly
Replace the corresponding optional
service card
320
IP-GW H.323
Dummy Call Test
Error
•
Detection of IP-GW H.323 •
Dummy Call Test error
•
Replace the corresponding optional
service card
Collect the log data of IP-GW (refer to
the documentation for the IP-GW card)
321
IP-GW Gatekeeper
Error
•
Detection of Gatekeeper
access error
•
Check the IP address setting of
Gatekeeper
Check whether the Gatekeeper is
connected to the network and work
properly
Check the route to the Gatekeeper
•
•
322
IP-GW Gatekeeper
Registration Error
•
Gatekeeper Registration
is failed
•
Check the Gatekeeper setting
323
IP-GW SDRAM
Failure
•
Detection of IP-GW
SDRAM error
•
Replace the corresponding optional
service card
324
IP-GW DPRAM
Failure
•
Detection of IP-GW
DPRAM error
•
Replace the corresponding optional
service card
325
IP-GW LAN Chip
Failure
•
Detection of IP-GW LAN
Chip failure
•
Replace the corresponding optional
service card
Collect the log data of IP-GW (refer to
the documentation for the IP-GW card)
•
326
IP-GW Stop
•
IP-GW is stopped from a
remote maintenance PC
•
This information is logged when IP-GW
is stopped from a remote maintenance
PC
330
Loop current
detection error
•
Detection of LCOT loop
current error
•
Change the corresponding trunk status
back to In Service
Enter the feature number to clear Busy
Out status
The trunk status is automatically
changed back to In Service by system
diagnosis performed at a
preprogrammed time every day
•
•
350
IP-unit SDRAM bit
error
351
IP-unit download
data check-sum error
352
IP-unit DSP failure
•
Optional service card
malfunction: IP-EXT
•
•
•
Optional service card
malfunction: IP-EXT
•
The IP-EXT card will be rebooted
automatically if the error is temporary
Replace the corresponding IP-EXT
card if the card is not rebooted
Replace the corresponding optional
service card
Installation Manual
237
4.1 Troubleshooting
Error Code
353
Error Message
IP-PT DSP failure
PROBABLE CAUSE
•
IP-PT malfunction
SOLUTION
•
•
355
IP-unit alive check
error
356
IP/TEL-unit
communication error
357
IP-unit FLASH
access error
358
IP-unit boot error
359
IP-unit DSP failure
(boot diagnosis)
360
IP-PT SUB-CPU
failure
•
Optional service card
malfunction: IP-EXT
•
•
The IP-PT will be rebooted
automatically if the error is temporary
Replace the corresponding IP-PT if the
IP-PT is not rebooted
The IP-EXT card will be rebooted
automatically if the error is temporary
Replace the corresponding IP-EXT
card if the card is not rebooted
•
Optional service card
malfunction: IP-EXT
•
Replace the corresponding optional
service card
•
IP-PT malfunction
•
The IP-PT will be rebooted
automatically if the error is temporary
Replace the corresponding IP-PT if the
IP-PT is not rebooted
•
361
IP-PT DHCP server
no response
•
•
DHCP server is not active •
Network malfunction
Consult your network administrator
362
IP-PT Rebooted
(cause DHCP
server)
•
•
•
DHCP server is not active •
Network malfunction
Network configuration has
been changed
Consult your network administrator
370
IP-GW Rebooted by •
Maintenance
Console
IP-GW is rebooted from a •
remote maintenance PC
This information is logged when IP-GW
is rebooted from a remote
maintenance PC
371
IP-GW Rebooted
Optional service card
malfunction: IP-GW
Check whether the software version of
the IP-GW card is correct
Replace the corresponding optional
service card
•
•
•
372
NDSS message over •
IPGW notification caused by IPGW Tx
resource limitation
373
NDSS message over
IPGW notification caused by IPGW Rx
resource limitation
374
NDSS message over
IPGW notification caused by shortage
of IPGW resource
238
Installation Manual
Optional service card
malfunction: IP-GW
•
•
Ignore if not frequent
Change the IP-GW card status to Out
of Service, and then back to In Service
4.1 Troubleshooting
Error Code
Error Message
PROBABLE CAUSE
SOLUTION
375
NDSS message over •
IPGW notification caused by Network
side
Network malfunction
•
•
Ignore if not frequent
Consult your network administrator
390
Digital signal
synchronization
established
•
Synchronisation of digital
line established or
restored
•
This information is logged when
synchronisation of digital line is
established, and does not indicate an
error condition that needs to be solved
391
Data Link
established
•
•
Connection with PC
Phone/PC Console or
Voice Processing System
(DPT Integration)
established or restored
This information is logged when
connection with PC Phone/PC
Console or Voice Processing System
(DPT Integration) is established, and
does not indicate an error condition
that needs to be solved.
However, if this is logged frequently
(with "305 Data Link failure"), check the
connection as it may not be done
properly.
392
Clock master card
selected
•
•
Clock master card has
been changed to the one
indicated by the sub code
Check if the proper card is selected as
the new clock master card
393
LAN Carrier detected •
IP-GW card connected to •
the LAN
This information is logged when
synchronisation of LAN is established
394
IP-GW Core Data
Link established
•
IP-GW Core Data Link
established
•
This information is logged when IP-GW
Core Data Link is recovered
395
IP-GW Gatekeeper
Error Cleared
•
Connection to the
Gatekeeper is recovered
•
This information is logged when
connection to the Gatekeeper is
recovered
396
IP-GW Run
•
IP-GW is started from a
remote maintenance PC
•
This information is logged when IP-GW
is started from a remote maintenance
PC
510*
SMDR disconnect
•
RS-232C cable not
connected
Breaking of RS-232C
cable
Printer (terminal
equipment) malfunction
•
•
Check the RS-232C cable
Check the terminal equipment
•
•
Installation Manual
239
4.1 Troubleshooting
240
Installation Manual
Section 5
Appendix
Installation Manual
241
5.1 Revision History
5.1
Revision History
5.1.1
Version 1.1
New Options
•
System Components Table
•
KX-TDA0105
Memory Expansion Card (MEC)
•
KX-TDA0182
8-Port DID Card (DID8)
•
KX-TDA0183
4-Port Analogue Trunk Card (LCOT4)
•
KX-TDA0484
4-Channel VoIP Gateway Card (IP-GW4E)
•
KX-TDA0143
4 Cell Station Interface Card (CSIF4)
•
KX-TDA0141CE
2-Channel Cell Station Unit Using a DHLC/DLC Card (PT-interface CS) for
DECT Portable Station
•
KX-TDA0141
2-Channel Cell Station Unit Using a DHLC/DLC Card (PT-interface CS) for
2.4 GHz Portable Station
New Contents
•
2.7.3 Digital EXtra Device Port (Digital XDP) Connection
Changed Contents
•
242
1.4.3 System Capacity
Installation Manual
5.1 Revision History
5.1.2
Version 2.0
New Options
•
System Components Table
•
KX-TDA0490
16-Channel VoIP Gateway Card (IP-GW16)
•
KX-TDA0470
16-Channel VoIP Extension Card (IP-EXT16)
•
KX-TDA0164
4-Port External Input/Output Card (EIO4)
•
KX-TDA0168
Extension Caller ID Card (EXT-CID)
•
KX-TDA0820
SD Memory Card for Software Upgrade
•
KX-TDA0920
SD Memory Card for Software Upgrade to Enhanced Version
Changed Contents
•
•
1.4.3 System Capacity
2.10.1 Connection of Doorphones, Door Openers, External Sensors, and External Relays
Installation Manual
243
5.1 Revision History
244
Installation Manual
Index
Installation Manual
245
Index
Numerics
16-Channel Echo Canceller Card (KX-TDA0166)
24, 132
16-Channel VoIP Extension Card (KX-TDA0470)
25, 121
16-Channel VoIP Gateway Card (KX-TDA0490)
26, 105
16-Port Analogue Trunk Card (KX-TDA0181)
24, 75
16-Port Digital Extension Card (KX-TDA0172)
24, 114
16-Port Single Line Telephone Extension Card (KX-TDA0174)
24, 119
16-Port Single Line Telephone Extension with Message Lamp Card (KXTDA0175)
24, 119
2-Port Doorphone Card (German Type) (KX-TDA0162)
24, 126
4 Cell Station Interface Card (KX-TDA0143)
24, 107
4-Channel Message Card (KX-TDA0191)
25, 133
4-Channel VoIP Gateway Card (KX-TDA0480)
25, 101
4-Channel VoIP Gateway Card (KX-TDA0484)
25, 103
4-Port Analogue Trunk Card (KX-TDA0183)
25, 75
4-Port BRI Card (KX-TDA0284)
25, 90
4-Port Doorphone Card (KX-TDA0161)
24, 124
4-Port External Input/Output Card (KX-TDA0164)
24, 129
8 Cell Station Interface Card (KX-TDA0144)
24, 107
8-Port Analogue Trunk Card (KX-TDA0180)
24, 75
8-Port BRI Card (KX-TDA0288)
25, 90
8-Port Caller ID Card (KX-TDA0193)
25, 80
8-Port Caller ID/Pay Tone Card (KX-TDA0189)
25, 79
8-Port DID Card (KX-TDA0182)
25, 77
8-Port Digital Extension Card (KX-TDA0171)
24, 112
8-Port Digital Hybrid Extension Card (KX-TDA0170)
24, 109
8-Port E & M Trunk Card (KX-TDA0184)
25, 81
8-Port Single Line Telephone Extension Card (KX-TDA0173)
24, 116
A
About the Other Manuals
10
After Site Survey
161, 187
Amphenol Connector Pin Assignment Chart
Appendix
241
Attaching a Ferrite Core
57
60
B
Backup Batteries Connection
49
Basic Shelf
20
Basic System Construction
20
Before Installation
38
Before Site Survey
153, 181
BRI4 and BRI8 Cards
90
Built-in Small Call Centre Features
18
Connection Diagram for External Sensor
131
Connection of 2.4 GHz Portable Stations
173
Connection of DECT Portable Stations
145
Connection of Doorphones, Door Openers, External Sensors, and External
198
Relays
Connection of Extensions
136
Connection of Peripherals
201
Construction of Basic Shelf
20
Covering the Blank Slots
52
CSIF4 and CSIF8 Card
107
CTI Link Card (KX-TDA0410)
25, 134
CTI-LINK Card
134
CTI—First Party Call Control
144
CTI—Third Party Call Control
134, 204
D
DHLC8 Card
109
DID8 Card
77
Digital EXtra Device Port (Digital XDP) Connection
Digital XDP
139
DLC16 Card
114
DLC8 Card
112
Door Opener
124, 126, 198
Doorphone
124, 126, 198
DPH2 Card
126
DPH4 Card
124
E
E&M8 Card
81
E1 Card
87
E-1 Trunk Card (KX-TDA0188)
25, 87
ECHO16 Card
132
EIO4 Card
129
EXT-CID Card
118
Extension Caller ID Card (KX-TDA0168)
24, 118
External Relay
129, 198
External Sensor
129, 198
EXtra Device Port (XDP) Mode
137, 139
F
Fastening Amphenol Type Connector
59
First Party Call Control CTI Connection
144
Floor Standing (KX-TDA200 Only)
65
Frame Earth Connection
48
C
G
Calculation Example (KX-TDA100)
34
Calculation Example (KX-TDA200)
35
Cards Installed in the Slots of the Hybrid IP-PBX
30
Cards Mounted on Other Optional Service Cards
32
Changed Contents
242, 243
Characteristics
29
CID/PAY8 Card
79
CID8 Card
80
Computer Telephony Integration (CTI) Features
18
Confirming the Trunk Connection
210
Connecting a Cell Station to the Hybrid IP-PBX
162, 188
Connection
215, 224
General Description
27
Guide for the KX-TDA Maintenance Console
246
Installation Manual
139
213
H
Handling of the Cables
53
Hospitality Features
19
I
Installation
37
Installation of the Extension Cards
107
Installation of the Hybrid IP-PBX
40
Installation of the KX-TDA Maintenance Console
217
Index
Installation of the Main Processing Card
71
Installation of the Other Cards
123
Installation of the Trunk Cards
75
Installation Precautions
38
Installing and Starting the KX-TDA Maintenance Console
Installing the KX-TDA Maintenance Console
218
Installing/Removing the Optional Service Cards
50
Installing/Replacing the Power Supply Unit
44
IP-EXT16 Card
121
IP-GW16 Card
105
IP-GW4 Card
101
IP-GW4E Card
103
L-Type Power Supply Unit (KX-TDA0103)
M
217
Maximum Cabling Distances of the Extension Wiring (Twisted Cable)
136
Maximum Terminal Equipment
33
MEC Card
73
MEC Card Calculation
33
Memory Expansion Card (KX-TDA0105)
24, 73
MPR Card
71
MSG4 Card
133
M-Type Power Supply Unit (KX-TDA0104)
26, 44
K
N
KX-TDA0103 (L-Type Power Supply Unit)
26, 44
KX-TDA0104 (M-Type Power Supply Unit)
26, 44
KX-TDA0105 (Memory Expansion Card)
24, 73
KX-TDA0108 (S-Type Power Supply Unit)
26, 44
KX-TDA0143 (4 Cell Station Interface Card)
24, 107
KX-TDA0144 (8 Cell Station Interface Card)
24, 107
KX-TDA0161 (4-Port Doorphone Card)
24, 124
KX-TDA0162 (2-Port Doorphone Card (German Type))
24, 126
KX-TDA0164 (4-Port External Input/Output Card)
24, 129
KX-TDA0166 (16-Channel Echo Canceller Card)
24, 132
KX-TDA0168 (Extension Caller ID Card)
24, 118
KX-TDA0170 (8-Port Digital Hybrid Extension Card)
24, 109
KX-TDA0171 (8-Port Digital Extension Card)
24, 112
KX-TDA0172 (16-Port Digital Extension Card)
24, 114
KX-TDA0173 (8-Port Single Line Telephone Extension Card)
24, 116
KX-TDA0174 (16-Port Single Line Telephone Extension Card)
24, 119
KX-TDA0175 (16-Port Single Line Telephone Extension with Message Lamp
Card)
24, 119
KX-TDA0180 (8-Port Analogue Trunk Card)
24, 75
KX-TDA0181 (16-Port Analogue Trunk Card)
24, 75
KX-TDA0182 (8-Port DID Card)
25, 77
KX-TDA0183 (4-Port Analogue Trunk Card)
25, 75
KX-TDA0184 (8-Port E & M Trunk Card)
25, 81
KX-TDA0187 (T-1 Trunk Card)
25, 84
KX-TDA0188 (E-1 Trunk Card)
25, 87
KX-TDA0189 (8-Port Caller ID/Pay Tone Card)
25, 79
KX-TDA0190 (Optional 3-Slot Base Card)
25, 123
KX-TDA0191 (4-Channel Message Card)
25, 133
KX-TDA0193 (8-Port Caller ID Card)
25, 80
KX-TDA0196 (Remote Card)
25, 74
KX-TDA0284 (4-Port BRI Card)
25, 90
KX-TDA0288 (8-Port BRI Card)
25, 90
KX-TDA0290 (PRI Card [PRI23])
25, 98
KX-TDA0290CE/CJ (PRI Card [PRI30])
25, 94
KX-TDA0410 (CTI Link Card)
25, 134
KX-TDA0470 (16-Channel VoIP Extension Card)
25, 121
KX-TDA0480 (4-Channel VoIP Gateway Card)
25, 101
KX-TDA0484 (4-Channel VoIP Gateway Card)
25, 103
KX-TDA0490 (16-Channel VoIP Gateway Card)
26, 105
KX-TDA0820 (SD Memory Card for Software Upgrade)
26, 71
KX-TDA0920 (SD Memory Card for Software Upgrade to Enhanced
Version)
26, 71
Names and Locations
41
Networking Features
18
New Contents
242
New Options
242, 243
L
LCOT4, LCOT8, and LCOT16 Cards
75
26, 44
O
OPB3 Card
123
Opening/Closing the Front Cover
42
Operation
226
Optional 3-Slot Base Card (KX-TDA0190)
Options
24
Overview
145, 173, 214
25, 123
P
Parallel Connection of the Extensions
137
Parallel Mode
137, 139
Parallelled Telephone Features
19
Password Security
217
PC Phone/PC Console Features
19
Portable Station (PS) Features
19
Power Failure Connections
205
Power Supply Unit Selection
34
PRI Card (PRI23) (KX-TDA0290)
25, 98
PRI Card (PRI30) (KX-TDA0290CE/CJ)
25, 94
PRI23 Card
98
PRI30 Card
94
Procedure Overview
147, 175
R
Remote Card (KX-TDA0196)
Revision History
242
RF Specification
145
RMT Card
74
25, 74
S
Safety Installation Instructions
38
Safety Instructions
44
SAFETY REQUIREMENTS
5
SD Memory Card
71
SD Memory Card for Software Upgrade
26, 71
SD Memory Card for Software Upgrade to Enhanced Version
Site Planning
149, 177
Site Survey
183
Site Survey Using the KX-TCA255/KX-TD7590
157
26, 71
Installation Manual
247
Index
SLC16 and MSLC16 Cards
119
SLC8 Card
116
Specifications
27
Starting the Hybrid IP-PBX
209
Starting the KX-TDA Maintenance Console and Assigning the Basic Items
218
(Quick Setup)
S-Type Power Supply Unit (KX-TDA0108)
26, 44
Surge Protector Installation
68
System Capacity
30
System Components Table
2
System Connection Diagram
21
System Highlights
18
System Outline
17
T
T1 Card
84
T-1 Trunk Card (KX-TDA0187)
25, 84
The Structure of this Manual
10
Troubleshooting
221, 222
Troubleshooting by Error Log
229
Types of Connectors
55
U
Unpacking
40
Using a CSIF Card
162, 188
Using a DHLC/DLC Card
163, 189
Using a Modular T-Adaptor
137, 139, 141
Using an EXtra Device Port
138
Using the Reset Button
228
V
Version 1.1
242
Version 2.0
243
Voice Mail Features
18
W
Wall Mounting (CS)
171, 196
Wall Mounting (KX-TDA100)
63
Wall Mounting (KX-TDA200)
61
Wiring Precautions
38
248
Installation Manual
Index
Installation Manual
249
Panasonic Communications Co., Ltd.
1-62, 4-chome, Minoshima, Hakata-ku, Fukuoka 812-8531, Japan
Copyright:
This material is copyrighted by Panasonic Communications Co., Ltd., and may be reproduced for internal use
only. All other reproduction, in whole or in part, is prohibited without the written consent of Panasonic
Communications Co., Ltd.
2003 Panasonic Communications Co., Ltd. All Rights Reserved.
PSQX2633VA KK0103AH6094
Download PDF