Daewoo Electronics DDQ-9H1SC User's Manual

Add to my manuals
33 Pages

advertisement

Daewoo Electronics DDQ-9H1SC User's Manual | Manualzz

OWNER'S MANUAL

DDQ-9H1SC

BEFORE USING TELEVISION RECEIVER,

READ AND OBSERVE ALL OF THIS OWNER’S MANUAL.

Part No. 11906570B

IMPORTANT SAFEGUARDS

HOW TO GET THE MOST ENJOYMENT FROM YOUR NEW COLOR TV SET

Your new Color TV incorporates a host of features designed to give you excellent performance.

In addition, this model utilizes a highly sophisticated Control Microprocessor that can give you unprecedented convenience and control in the areas of Picture Adjustment, Channel

Tuning, On-Screen Information.

We therefore strongly urge that you read all of these instructions before using your TV for the first time.

It is especially important that you read and follow the instructions under the heading:

"CHANNEL MEMORY" on page 16.

SAFETY INSTRUCTION

ANTENNA

Unless your TV is connected to a Cable TV system or to a centralized antenna system, a good outdoor color TV antenna is recommended for the best performance. However, if you are located in a strong signal area that is free from interference and ghost conditions (multipath), an indoor antenna may be insufficient. The two pole antenna packed with this set is for your convenience only. It is not capable of providing you with the sharp detail and rich color that this television was designed to display.

LOCATION

Select an area where sunlight or bright indoor illumination will not fall directly on the picture screen.

Also, be sure that the location selected allows a free flow of air to and from the perforated back cover of the set.

NOTES

Never remove the back cover of the set. This can expose you to very high voltage and other hazards.

If the set does not operate properly, unplug it and call your dealer or service shop.

VIEWING

This color receiver may be viewed from any desired distance. Most viewers prefer a distance of three to six feet or more depending on-screen size for maximum eye comfort.

Caution

To prevent electric shock do not use this (polarized) plug with an extension cord, receptacle or other outlet unless the blades can be inserted to prevent blade exposure.

2

Caution

Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could avoid the user’s authority to operate the equipment.

GRAPHICAL SYMBOLS EXPLANATION

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN.

CAUTION : TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT

REMOVE COVER(OR BACK)

NO PARTS INSIDE.

REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

This lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (Servicing) instructions in the literature accompanying the appliance.

FEATURES

FS(Full-Square) picture tube.

181-channel cable-compatible frequency synthesizer tuner.

Full on-screen display of all functions.

Video/Audio input/output terminals.

With various picture functions.(STANDARD, DYNAMIC, MILD, CUSTOM) and sound (STANDARD, MUSIC, MOVIE, SPEECH, CUSTOM) functions.

TIME (Clock, Sleep Timer, On/Off timer)

Automatic power shut-off.

Full Remote Control.

Built-in CCD (Closed Caption Decoder)

IMPORTANT FOR LASER PRODUCTS

LASER This Digital Video Disc Player employs a Laser System. To ensure proper use of this product please read this owner's maual carefully and retain for future reference. Should the unit require maintenance, contact an authorized service location - see service procedure.

Use of control adjustments or the performance of procedures other than those specified may result in hazardous radiation when open and interlocks defeated.

DO NOT STARE INTO THE BEAM.

DANGER Visible laser radiation when open and interlock failed or defeated. Avoid direct exposure to beam.

CAUTION Do not open the top cover. There are no user serviceable parts inside the Unit; leave all servicing to qualified service personnel.

CLASS 1

LASER PRODUCT

3

CONTENTS

Important Safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Location of Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Connecting External Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Antenna Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Cable TV(CATV) Connecton . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Video/Audio Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Remote Control Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

TV FUNCTION & OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

On Screen Language Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Basic of MENU Operation Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Channel Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Picture Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Sound Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Time Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Other Useful Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

DVD Function & Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Disc Requirement/Copyright Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Remote Control Unit(DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Basic Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Searching for a Specific Screen/Song During Playback . . . . . . . . . . . . . . . . 41

Setting a Custom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Changing the Audio/Subtitle Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Change the Size and of the Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Selecting a Menu and 3D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Using the Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Setting the Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Setting the Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Setting the Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Setting the Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Custom Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Setting Parental Rating Level and Password . . . . . . . . . . . . . . . . . . . . . . . . 54

Operating with an MP3 Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Use of MP3 Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Use of JPEG Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Trouble Shooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Interference Causes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

4

LOCATION OF CONTROLS

5

CONNECTING EXTERNAL EQUIPMENT

AUDIO/VIDEO IN JACK

If your receiver has AUDIO/VIDEO IN JACK, connect this JACK to VCR and TV receiver.

Select AV by pressing the AV mode selection key on the remote control.

Push PLAY key of your VCR. The advantage of this connection is a superior quality of picture and sound during play back.

ANTENNA To "RF IN"

ANTENNA

From Audio/Video Out (VCR)

OR

To "RF IN"

To Audio/Video Input(TV)

From Audio/Video Out (VCR)

To Audio/Video Input(TV)

6

CONNECTING EXTERNAL EQUIPMENT

EARPHONES

The earphones must have an impedance of between 8 and 32 ohms and have a 3.5mm

stereo jack plug.

1. Plug the earphone jack into the earphone socket on the right hand side of the TV.

2. Adjust the volume of sound using VOL-,+ buttons.

NOTE : If earphone is inserted there will be no sound output at the loud speaker.

VCR OPERATION BY USING THE RF OUT

To connect a home VCR to the receiver, connect the coaxial cable from the RF OUT socket of the VCR to the antenna socket of the TV SET, and connect the antenna lead-in cable to the RF IN socket of the recorder.

ANTENNA To "RF IN"

Coaxial cable

To "RF OUT"

To antenna socket

7

ANTENNA CONNECTION

Antenna

The antenna requirements for a good color television reception are more important than those for black & white television reception. For this reason,a good quality of outdoor antenna is strongly recommended.

The following is a brief explanation of the type of connections that are provided with the various antenna systems:

1. A 75 ohm system is generally a round cable with F-type connector that can easily be attached to a terminal without tools.

2. A 300 ohm system is a flat "twin-lead" cable that can be attached to a 75 ohm terminal through a 300-75 ohm ADAPTOR.

(Refer to 300-75 ohm ADAPTOR as supplied)

F-type connector

75-ohm coaxial cable (round)

300-ohm twin-lead cable (flat)

OUTDOOR ANTENNA CONNECTION

Use one of the following two diagrams if you connect an outdoor antenna.

A : Using a VHF/UHF combination outdoor antenna.

B : Using separate VHF and/or UHF outdoor antenna.

Connect an outdoor antenna cable lead-in to the COAXIAL CABLE CONNECTOR on the rear of the TV set.

A. Combination VHF/UHF Antennas

VHF/UHF ANTENNA

300/75-ohm

ADAPTOR

(as supplied)

VHF/UHF ANTENNA

300-ohm twin-lead or

75-ohm coaxial cable

ANT/

CABLE

REAR OF TV

75Ω

B. Separated VHF/UHF Antennas

VHF ANTENNA UHF ANTENNA or

300-ohm twin-lead

300-ohm twin-lead

75-ohm coaxial cable

COMBINER

(not supplied)

IN OUT

REAR OF TV

ANT/

CABLE

75Ω

8

CABLE TV(CATV) CONNECTION

A 75 ohm coaxial cable connector is built into the set for easy hookup.

When connecting the 75 ohm coaxial cable to the set, screw the 75 ohm cable to the

COAXIAL CABLE CONNECTOR.

Some cable TV companies offer "premium pay channels". Since the signals of these premium pay channels are scrambled, a cable TV converter/descrambler is generally provided to the subscriber by the cable TV company. This converter/descrambler is necessary for normal viewing of the scrambled channels. (Place your TV on channel 3 or 4, typically one of these channels is used. If this is unknown, consult your cable TV company. One possible method of utilizing the converter/descrambler provided by your cable TV company is explained below.

NOTE : RF switch equipped with position A/B(not provided) is required.

"A" position on the RF switch (not supplied)

: You can view all unscrambled channels using the TV's channel keys.

"B" position on the RF switch (not supplied)

: You can view the scrambled channels via the converter/descrambler using the converter's channel keys.

RF switch (not supplied)

OUT

A

IN

B

Two-set signal splitter

(not supplied)

Cable TV line

TV

OUT IN

Cable TV converter/ descrambler

VIDEO/AUDIO CONNECTIONS

Prior to making any connections to your TV set, be sure to turn the POWER off.

For a more detailed understanding of each connection, it is recommended that you read the instruction manual for each connected component.

If you use video or audio equipment placed near the Monitor/Receiver,picture and/or sound may become distorted due to interference between these components.

In such a case,separate each piece of equipment at a sufficient distance.

The following shows examples for connecting external equipment.

Do not connect another audio source to the same speaker to which the TV set is connected, otherwise damage may result to the amplifier of the TV set or to that of the other audio source.

75 ohm

ANT

VCR or VDP

TO VIDEO IN TO VIDEO OUT

VIDEO AUDIO TO AUDIO IN TO AUDIO OUT

VHF/ UHF

OUTPUT

AUDIO/VIDEO INPUT

1.Connect the VIDEO OUT jack from the VCR to the VIDEO IN jack on the TV.

2.Connect the AUDIO OUT jack from the VCR to the AUDIO IN jack on the TV.

3.Turn TV on and press VIDEO button on the Remote control to select VIDEO mode.

4.Turn the VCR on and Playback tape.(consult your VCR system's owner's manual.)

9 10

REMOTE CONTROL USE

Correct

Point at the Remote Control Sensor of the TV set.

The maximum operable distance is approximately 6m from the Remote Control Sensor, and not more than 30 to either side of center.

The operation of the Remote Control is most effective when there is nothing between it and the Remote Control Sensor.

The duration of the batteries is approximately 6 months to 1 year.

Replace the batteries when the remote control operation becomes unstable.

Battery Installation/Notes

Press the indentation and lift up the cover in the direction of the arrow.

Correctly install the batteries, observing polarities as shown

Do not use a combination of old and new batteries or batteries of different types.

If batteries become exhausted, remove and replace them soon.

When battery leakage occurs, clean the battery compartment with a soft cloth and replace the batteries.

100 Button

Direct channel selection Buttons

TV Menu Button

Mute Button

Display Button

MTS Button

DVD 3D Button

TV/Video Button

Power Button

DVD Control Button

Channel Down( )/

Up( ) Buttons

Volume Down(-)/

Up(+) Buttons

Quick View Buttons

Add/Delete Buttons

DVD Function Buttons

NOTICE : To select channels (to jump directly to a desired channel)100 through 125, press the

"1" button for 2 second and then the last two digits within a few seconds after pressing the " 1" button.

11

TV FUNCTION & OPERATION

Connect either Antenna or Cable TV according to "ANTENNA CONNECTION" instruction on page 8.

Insert batteries into the Remote Control unit according to "REMOTE CONTROL USE" instruction on page 11.

Connect the power cord to AC outlet.

– Voltage is between 120 Volts.

– Frequency is compatible (50/60Hz)

POWER ON

1) Press the MAIN POWER switch on the control panel of the set to turn on and stand-by

RED LED will illuminate.

2) The TV set is now in stand-by mode, to turn it on press CH of the set or press power or CH key located front panel key on the remote control hand unit.

The NO LED will illuminate.

or or

POWER OFF Remote control (Front panel)

1) Press the POWER key on the remote control hand unit.

The RED LED will illuminate.

2) If you want to turn off for a long time, Press the MAIN POWER switch on the control panel.

3) When there is no broadcasting signal, the TV set goes off automatically after 15 minutes.

In this case, the TV set goes to stand-by mode, there for The RED LED will illuminate.

This function is the same as in the AV mode.

NOTE : Power button of front panel is not active when you use the DC battery cord.

CHANNEL SELECTION

Use CHANNEL ( ) buttons on the Remote Control (or CHANNEL ( ) buttons on the front panel).

Pressing the ( ) button to advances for the higher channels, and press the ( ) button to go down for the lower channels.

NOTE : Certain channels have been preset at the factory. It may be necessary to add or erase some channels in your areas. See "AUTO PROGRAM" on page 17 for presetting channels.

Channels can be selected directly by using 10-Digit Keypad on the Remote Control.

For example, if you select channel 5, press "0" first, then press "5". (Be sure to press "0" first, before pressing "5" for channel 5.)

For channel 120, press the 100 button first, then press "2", "0". Also refer to the CABLE

CHANNEL CONVERSION CHART below.

12

CABLE TV CHANNEL CONVERSION CHART

In addition to the normal TV reception from an antenna for VHF (Channels 2-13) and UHF

(Channel 14-69), your TV set is equipped to receive non-scrambled cable TV channels.

SubMid band (A-8, A-5-A-1), Mid band (A-I) Super band (J-W) Hyper band (W 1 - W 28) and Ultra band (W 29 - W 84) can be received by using the channel selections as shown in the following chart.

A-8 A-5 A-4 A-3 A-2 A-1 A B C D E F G H I J K L M N

01

O

28

95

P

96

Q

97

R

98

S

99

T

14

U

15

V

16

W

17 18

W 1 W 2

19 20 21 22 23 24 25 26

W 3 W 4 W 5 W 6 W 7 W 8 W 9 W 10

29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46

W 11 W 12 W 13 W 14 W 15 W 16 W 17 W 18 W 19 W 20 W 21 W 22 W 23 W 24 W 25 W 26 W 27 W 28 W 29

47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65

27

W 30 W 31 W 32 W 33 W 34 W 35 W 36 W 37 W 38 W 39 W 40 W 41 W 42 W 43 W 44 W 45 W 46 W 47 W 48

66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84

W 49 W 50 W 51 W 52 W 53 W 54 W 55 W 56 W 57 W 58 W 59 W 60 W 61 W 62 W 63 W 64 W 65 W 66 W 67

85 86 87 88 89 90 91 92 93 94 100 101 102 103 104 105 106 107 108

W 68 W 69 W 70 W 71 W 72 W 73 W 74 W 75 W 76 W 77 W 78 W 79 W 80 W 81 W 82 W 83 W 84

109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125

Regular cable channel designations.

Your TV set's corresponding on-screen CABLE channel numbers.

Press VOLUME

Remote Control or( sound volume, the decrease sound volume. buttons on either the

) front panel to adjust volume to your desired listening level.

Pressing the button will increase button will

The volume level is indicated on the screen by reference number (0-100)and by bar scale as shown.

VOLUME 25

ADJ.

NOTES The volume level can be muted instantly by pressing MUTE button on the Remote

Control. See "MUTE Button" on page 34.

Your TV set can receive the normal TV channel(2-13) including the CABLE TV channel

NOTE TO CATV SYSTEM INSTALLER

This reminder is provided to call the CATV system installer’s attention to article 820-40 of the

NEC that provides guidelines for proper grounding and, in particular, specifies that cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

13

ON SCREEN LANGUAGE SELECTION

MENU

PICTURE

SOUND

TIME

SETUP

FUNCTION

LANGUAGE ENGLISH

: MOVE : ADJ.

: EXIT

1) Press the TV MENU button.

2) Press the CHANNEL UP/DOWN reach LANGUAGE mode. button to

3) Press the or VOLUME + button to select the desired language.

4) It will appear on the screen like below;

ENGLISH ESPAÑOL PORTUGUÊS FRANÇAIS

5) Press the TV MENU button to exit.

BASIC OPERATION

1. Press POWER button to turn the TV on.

2. Press TV MENU button and move the cursor to "SET UP" option and press or VOLUME + button, then the "SET UP" menu is displayed.

MENU

PICTURE

SOUND

TIME

SETUP

FUNCTION

LANGUAGE ENGLISH or

SET UP

ANTENNA

AUTO PROGRAM

FINE TUNE

CATV 2

0

: MOVE :SELECT : EXIT

: MOVE :SELECT : PREV.

3. Press VOLUME button to Select ANTENNA option.(TV or CATV)

4. Press CH / buttons to place cursor on the "AUTO PROGRAM " option and press VOL

+ button.

SET UP

ANTENNA

AUTO PROGRAM

FINE TUNE

CATV 2

0

AUTO PROGRAMMING 2 or

: MOVE :SELECT : PREV.

: STOP

5. Press CH / buttons to Select the channel you want.

6. Press VOL + or VOL - buttons to adjust volume to your desired listening level.

14

BASIS OF "MENU" OPERATION METHOD

You can execute every operation by pressing CH / buttons and VOL +/- or alternately.

If you learn one method, You can easily operate another function by viewing picture.

buttons

1. Pressing these buttons alternately makes every operation easy.

2. MOVE Press CH / buttons to place cursor.

3. PICTURE CHANGE Press VOL +/- or buttons to change picture by inputting selected function.

MENU

PICTURE

SOUND

TIME

SETUP

FUNCTION

LANGUAGE ENGLISH

: MOVE : SELECT : EXIT

TIME

CLOCK

SLEEP

TIMER

ON TIME

OFF TIME

ON CHANNEL

AM12:00

OFF

OFF

AM12:00

AM12:00

2

: MOVE : SELECT : PREV.

PICTURE

PICTURE STANDARD

CONTRAST 75

BRIGHTNESS 50

SHARPNESS 50

COLOR 50

TINT 0

: MOVE : ADJ.

: PREV.

FUNCTION

BLUE BACK

HALF TONE

CCD

: MOVE : ADJ.

ON

ON

OFF

SET UP

ANTENNA

AUTO PROGRAM

FINE TUNE

: PREV.

CATV2

0

SOUND

SOUND

EQUALIZER

BALANCE

SURROUND

: MOVE : ADJ.

STANDARD

0

OFF

AVL OFF

: PREV.

15

CHANNEL MEMORY(SET UP)

ANTENNA SELECTION

In this mode, you can change the broadcast mode between "TV" (for regular VHF/UHF channels) and " CATV " (for cable channels).

1. Press TV MENU button and move the cursor to "SET UP" option and press VOL + or button then the "SET UP" menu is displayed.

MENU

PICTURE

SOUND

TIME

SETUP

FUNCTION

LANGUAGE ENGLISH

: MOVE : SELECT : EXIT

SET UP

ANTENNA

AUTO PROGRAM

FINE TUNE

CATV 2

0

2. Press CH / buttons to place the cursor on the "ANTENNA" option and press VOL + or button. You can select "TV"(on-air) or "CATV"(cable TV) broadcast mode.

SET UP

ANTENNA

AUTO PROGRAM

FINE TUNE

CATV 2

0

SET UP

ANTENNA

AUTO PROGRAM

FINE TUNE

TV 2

0

3. After you have finished selecting "ANTENNA" mode, press TV MENU button repeatedly until the menu disappears.

16

CHANNEL MEMORY(SET UP)

AUTO PROGRAM

This function allows the channels to be memorized automatically to match the TV broadcasts and cable channels in your area.

1. Press TV MENU button and move the cursor to "SET UP" option and press VOL + or button, then the "SET UP" menu is displayed.

MENU

PICTURE

SOUND

TIME

SETUP

FUNCTION

LANGUAGE ENGLISH

: MOVE : SELECT : EXIT

SET UP

ANTENNA

AUTO PROGRAM

FINE TUNE

CATV 2

0

: MOVE : SELECT : PREV.

2. Press CH / buttons to place cursor on the "AUTO PROGRAM" option and press VOL + or button.

SET UP

ANTENNA

AUTO PROGRAM

FINE TUNE

CATV 2

0

AUTO PROGRAMMING 2

: STOP

When tuned to a channel in which TV program is broadcasted, this channel is memorized and the color changes from magenta to green.

After every channels were memorized, "SET UP" menu is displayed.

3. When you have finished "AUTO PROGRAMMING", press TV MENU button repeatedly until the menus disappear.

NOTES If the broadcast signal is weak, the channel will not be memorized.

In this case, perform the MANUAL MEMORY procedure.(Refer to the next page)

If you wish to stop this procedure during the operation, Press VOL + or button.

17

CHANNEL MEMORY(SET UP)

MANUAL MEMORY(channel add/delete)

1. TO ADD A CHANNEL

If you want to add to the memory a channel the TV did not store during AUTO PROGRAM, follow these steps.

Press the 10-Digit Keypad button to select a channel you want to view.

Press "A/D" button on the Remote Control.

The channel is added to memory and the color of the channel number changes from red to green.

CH ADDING CH DELETING

CATV 12

CHANNEL ADDED

CATV 12

CHANNEL DELETED

COLOR : GREEN COLOR : RED

2. TO DELETE CHANNEL

You can exclude the channels of your choice from the memorized channel.

Follow these steps to delete the channel in the TV's memory.

Press CH / buttons or Press the 10-Digit keypad button to select a channel you want to delete.

Press "A/D" button on the Remote Control.

The channel is removed from the memory, and the color of the channel number changes from green to red.

18

CHANNEL MEMORY(SET UP)

FINE TUNE

If the reception is clear, you do not have to fine-tune the channel, as this is done automatically during auto program and manual memory.

If however the signal is weak or distorted, you may have to fine-tune the channel manually.

1. Press CH / buttons or Press the 10-Digit keypad button to adjust a channel you want.

2. Press TV MENU button and move the cursor to "SET UP" option and press VOL + or button, then the "SET UP" menu is displayed.

MENU

PICTURE

SOUND

TIME

SETUP

FUNCTION

LANGUAGE ENGLISH

: MOVE : SELECT : EXIT

SET UP

ANTENNA

AUTO PROGRAM

FINE TUNE

CATV 2

0

: MOVE : SELECT. :PREV.

3. Press CH / buttons to place the cursor on the "FINE TUNE" option.

4. Use VOL +/- or buttons until you obtain a sharp and clear picture and good sound quality.

SET UP

ANTENNA

AUTO PROGRAM

FINE TUNE

CATV 2

0

SET UP

ANTENNA

AUTO PROGRAM

FINE TUNE

CATV 2

+1

A/D:MEMORY A/D:MEMORY

5. If you wish to memorize adjusted FINE TUNE state, press "A/D" button, and then the memorie icon is displayed.

If you wish to initialize it, press that button again, and then the icon disappear.

NOTES The memorized channel does not operate AFT(automatic frequency tuning)mode.

The FINE-TUNE is operated only selected channel.

After the "AUTO PROGRAM", the memorized channel operate AFT(automatic frequency tuning)mode automatically.

19

PICTURE ADJUSTMENT 1

USING ON-SCREEN MENU

You can sequentially select any one of the four possible preferred analogue picture presets.

MENU

PICTURE

SOUND

TIME

SETUP

FUNCTION

LANGUAGE ENGLISH

: MOVE :SELECT : EXIT

Press the TV MENU button. Move the cursor to PICTURE by pressing the CH

/ buttons and press the VOL + or button.

PICTURE

PICTURE STANDARD

CONTRAST 75

BRIGHTNESS 50

SHARPNESS 50

COLOR 50

TINT 0

Move the cursor to PICTURE by pressing the CH / buttons.

: MOVE : ADJ.

: PREV.

PICTURE

PICTURE DYNAMIC

CONTRAST 100

BRIGHTNESS 50

SHARPNESS 75

COLOR 50

TINT 0

: MOVE : ADJ.

: PREV.

Press the VOL +/- or button.

Whenever this button is pressed, the mode will change as follows.

STANDARD DYNAMIC

CUSTOM MILD

MODE

STANDARD

DYNAMIC

MILD

CUSTOM

PICTURE

Select this mode to view the factory-presetting standard picture.

Select this mode to view a powerful and clear picture.

- watch in the brighter(daylight) environments.

Select this mode to emphasize mildness

- When it is dark around to lessen the fatigue of eyes.

Select this mode to view the adjusted picture you want.

20

PICTURE ADJUSTMENT 2

You can sequentially select and adjust one of five picture levels.

Contrast, Brightness, Color, Sharpness or Tint e.g. : Contrast Adjustment.

MENU

PICTURE

SOUND

TIME

SETUP

FUNCTION

LANGUAGE ENGLISH

: MOVE :SELECT : EXIT

Press the TV MENU button. Move the cursor to PICTURE by pressing the CH

/ buttons and press the VOL + or button.

PICTURE

PICTURE STANDARD

CONTRAST 75

BRIGHTNESS 50

SHARPNESS 50

COLOR 50

TINT 0

: MOVE : ADJ.

: PREV.

Move the cursor to CONTRAST by pressing the CH / press the VOL +/- or buttons and buttons.

CONTRAST 75

: ADJ.

: PREV.

Adjust " CONTRAST " by VOL +/- or buttons.

When you have finished contrast adjustment, press TV MENU repeatedly until the menu disappears.

21

SOUND ADJUSTMENT

USING ON-SCREEN MENU

There is a choice of five audio settings by using the on-screen menu, the five settings can by viewed in the sequence illustrated.

MENU

PICTURE

SOUND

TIME

SETUP

FUNCTION

LANGUAGE ENGLISH

: MOVE :SELECT : EXIT

Press the TV MENU button. Move the cursor to SOUND by pressing the CH

/ buttons and press the VOL + or button.

SOUND

SOUND

EQUALIZER

BALANCE

SURROUND

STANDARD

0

OFF

Move the cursor to SOUND by pressing the CH /

AVL OFF buttons.

: MOVE : ADJ.

: PREV.

STANDARD

MUSIC

MOVIE

SPEECH

CUSTOM

SOUND

SOUND MUSIC

Press the VOL + or button.

EQUALIZER

BALANCE 0

Whenever this button is pressed, the

SURROUND OFF mode will change as follows.

AVL OFF

: MOVE : ADJ.

: PREV.

STANDARD MUSIC MOVIE SPEECH CUSTOM

Select this mode to use the factory presetting.

Select this mode when listening to music

Select this mode when viewing a movie.

Select this mode to hear voices clearly.

Select this mode to hear the adjusted sound you want. See EQUALIZER page.

22

SOUND ADJUSTMENT

EQUALIZER

You can adjust five frequency ranges to your preference.

MENU

PICTURE

SOUND

TIME

SETUP

FUNCTION

LANGUAGE ENGLISH

: MOVE : SELECT : EXIT

Press the TV MENU button. Move the cursor to SOUND by pressing the CH

/ buttons and press the VOL + or button.

SOUND

SOUND

EQUALIZER

BALANCE

SURROUND

: MOVE : ADJ.

STANDARD

0

OFF

Move the cursor to EQUALIZER by pressing the CH / buttons and press the VOL + or button.

: PREV.

EQUALIZER

50 50 50 50 50

120 500 1.5K

5K 10K

: ADJ : MOVE : PREV.

Adjust each frequency band, using

CH / buttons.

23

SOUND ADJUSTMENT

BALANCE

SOUND MENU

MENU

PICTURE

SOUND

TIME

SETUP

FUNCTION

LANGUAGE ENGLISH

: MOVE : SELECT : EXIT

Press the TV MENU button. Move the cursor to SOUND by pressing the CH

/ buttons and press the VOL + or button.

SOUND

SOUND

EQUALIZER

STANDARD Move the cursor to BALANCE by pressing the CH / buttons.

BALANCE 0

SURROUND OFF

AVL OFF

: MOVE : ADJ.

: PREV.

BALANCE 0

: ADJ. : PREV.

Press the VOL +/- or buttons.

The Sound BALANCE is adjusted.

24

SOUND ADJUSTMENT

SURROUND SOUND

SOUND MENU

MENU

PICTURE

SOUND

TIME

SETUP

FUNCTION

LANGUAGE ENGLISH

: MOVE : SELECT : EXIT

Press the TV MENU button. Move the cursor to SOUND by pressing the CH

/ buttons and press the VOL + or button.

SOUND

SOUND

EQUALIZER

STANDARD Move the cursor to SURROUND by pressing the CH / buttons.

BALANCE 0

SURROUND OFF

AVL OFF

: MOVE : ADJ.

: PREV.

Press the VOL + or buttons.

Whenever this button is pressed, the mode will change as follows.

OFF ON

25

SOUND ADJUSTMENT

AVL

SOUND MENU

MENU

PICTURE

SOUND

TIME

SETUP

FUNCTION

LANGUAGE ENGLISH

: MOVE : SELECT : EXIT

Press the TV MENU button. Move the cursor to SOUND by pressing the CH

/ buttons and press the VOL + or button.

SOUND

SOUND

EQUALIZER

BALANCE

SURROUND

STANDARD

0

OFF

AVL OFF

: MOVE : ADJ.

: PREV.

Move the cursor to AVL by pressing the

CH / buttons.

Press the VOL + or buttons.

Whenever this button is pressed, the mode will change as follows.

OFF ON

AVL(Automatic Volume Limitter)

Different sound sources fairly do not have the same volume level.

This results in annoying volume changes.

AVL solves the problem by equalizing the volume levels.

26

SOUND ADJUSTMENT

MTS

USING MTS BUTTON :

Your TV set incorporates an MTS (Multichannel Television Sound) decoder to receive stereo broadcasts and any accompanying SAP (Second Audio Program) such as another language sound track).

1. Press the MTS button

Depending on the audio signal type of the currently receiving broadcast, on-screen selection appears as follows:

Receiving signal

Stereo and SAP

On-screen selections

STEREO SAP MONO

Stereo or SAP

Mono

STEREO

MONO only

MONO or SAP MONO

The "STEREO", "SAP" text indicate that MTS mode is being broadcast.

When the power is switched on or channel is changed, the "STEREO", "SAP" text are automatically displayed, depending on the current broadcast.

MTS STEREO

NOTES

If the received signal is weak, noise may be heard.

In such a case, press MTS button to set to the MONO mode for better sound reception.

If the received SAP signal is weak, the SAP will not be heard.

Even if both STEREO and SAP broadcasts are received, both broadcasts cannot be heard at the same time.

Transmission of CABLE TV signals may differ from off-air TV broadcasts.

27

TIME SETTING

CLOCK

You can set the television’s clock so that the current time will be displayed when you press the

TV MENU button.

You must set the current time before you can set the automatic On/Off timer.

MENU

PICTURE

SOUND

TIME

SETUP

FUNCTION

LANGUAGE ENGLISH

: MOVE : SELECT : EXIT

Press TV MENU button and move the cursor to TIME by CH / buttons.

Press VOL + or button and press it again.

TIME

CLOCK

SLEEP

TIMER

ON TIME

OFF TIME

ON CHANNEL

WHITE

AM12:00

OFF

OFF

AM12:00

AM12:00

2

: ADJ. : MOVE : PREV.

GREEN

Adjust "HOUR " by CH / buttons.

Whenever these buttons are pressed, the hour increases or decreases by 1.

TIME

CLOCK

SLEEP

TIMER

ON TIME

OFF TIME

ON CHANNEL

GREEN

AM12:00

OFF

OFF

AM12:00

AM12:00

2

WHITE

Press VOL + or button and adjust

"MINUTE " by CH / buttons.

Whenever these buttons are pressed, the minute increases or decreases by 1.

: ADJ. : MOVE : PREV.

Press the TV MENU button to return to the main menu.

28

TIME SETTING

SLEEP TIMER

You can select a time period from 15 through 90 minutes so that the television automatically switches to power-off mode.

MENU

PICTURE

SOUND

TIME

SETUP

FUNCTION

LANGUAGE ENGLISH

: MOVE : SELECT : EXIT

Press TV MENU button the cursor to

TIME by pressing the CH / button and press the VOL + or button.

TIME

CLOCK

SLEEP

TIMER

ON TIME

OFF TIME

ON CHANNEL

AM12:00

OFF

OFF

AM12:00

AM12:00

2

: ADJ. : MOVE : PREV.

"TIME " is displayed on the screen.

Move the cursor to SLEEP by CH / buttons and press the VOL + or button to set SLEEP time.

Whenever VOL + or button is pressed, the time is changed.

OFF 15 30 45 60 90

NOTE : To cancel the sleep timer function, in this mode, press VOL + or button repeatedly until the word " OFF " is displayed.

TIME SETTING

ON/OFF TIMER

The ON/OFF time lets you use alarm and automatic off function.

MENU

PICTURE

SOUND

TIME

SETUP

FUNCTION

LANGUAGE ENGLISH

: MOVE : SELECT : EXIT

Press TV MENU button.

Move the cursor to TIME by pressing the

CH / buttons and press the VOL + or button.

"TIME " is displayed on the screen.

TIME

CLOCK

SLEEP

TIMER

ON TIME

OFF TIME

ON CHANNEL

: ADJ. : MOVE

AM12:00

OFF

ON

AM12:00

AM12:00

2

: PREV.

Move the cursor to Timer by CH / buttons and press VOL + or button to set " TIME R ON"

NOTES If you have not yet set the television’s clock, the message "CLOCK STOPPED" is displayed.

If this happens, refer to "CLOCK" on the previous page.

29 30

TIME SETTING

TIME

CLOCK

SLEEP

TIMER

ON TIME

OFF TIME

ON CHANNEL

: ADJ. : MOVE

AM12:00

OFF

ON

AM07:30

AM12:00

2

: PREV.

Move the cursor to "ON TIME" by CH / buttons and press the VOL +/- or buttons to set the time.

TIME

CLOCK

SLEEP

TIMER

ON TIME

OFF TIME

ON CHANNEL

: ADJ. : MOVE

AM12:00

OFF

ON

AM07:30

PM10:15

2

: PREV.

Move the cursor to "OFF TIME"by CH / buttons and press the VOL +/- or buttons to set the time.

Press " TV MENU " to return to the main menu.

AUTOMATIC POWER OFF MODE

If the set is not switched off when the TV station stops broadcasting, it will automatically go to power-off mode after about 15 minutes.

NOTES If you set "ON TIME" and "OFF TIME" with the same time, the "ON/OFF TIME" will be clear and please set again the "ON/OFF TIME".

If the power is disconnected (in case of a power failure) and reapplied later, the clock operation will stop.

31

TIME SETTING

ON TIME CHANNEL NUMBER

You can select the channel on which the TV turns on as programmed by ON-TIMER.

This function will not work if the TIMER is set to OFF or the current time has not been set.

TIME

CLOCK

SLEEP

TIMER

ON TIME

OFF TIME

ON CHANNEL

AM12:00

OFF

ON

AM07:30

PM10:15

2

: ADJ. : MOVE : PREV.

1) Move cursor to ON CHANNEL and press VOL + or button the color of the channel number changes to white.

2) Set channel number you want use

CH / buttons.

FUNCTION

1. Press the TV MENU button. Move the cursor to a FUNCTION by pressing the CH / buttons.

Adjust it by pressing the VOL + or button.

MENU

PICTURE

SOUND

TIME

SETUP

FUNCTION

LANGUAGE ENGLISH

: MOVE : SELECT : EXIT or

MENU

PICTURE

SOUND

TIME

SETUP

FUNCTION

LANGUAGE ENGLISH

: MOVE : SELECT : EXIT

FUNCTION

BLUE BACK

HALFTONE

CCD

OFF

OFF

OFF

: MOVE : ADJ.

: PREV.

32

FUNCTION

BLUE BACK

When no picture signal is inputed, or the signal is weak, the screen reverts to a blue back color.

FUNCTION FUNCTION

BLUE BACK

HALFTONE

CCD

OFF

OFF

OFF

BLUE BACK

HALFTONE

CCD

ON

OFF

OFF or

: MOVE : ADJ.

: PREV. : MOVE : ADJ.

: PREV.

On this feature disable to continue watching very weak signals.

HALFTONE

You can select Halftone mode in the on-screen.

FUNCTION

BLUE BACK

HALFTONE

CCD

OFF

OFF

OFF or

FUNCTION

BLUE BACK

HALFTONE

CCD

OFF

ON

OFF

: MOVE : ADJ.

: PREV. : MOVE : ADJ.

: PREV.

CCD

You can select closed caption mode.

In this mode, press VOL + or button.Whenever this button is pressed.

OFF CCD 1 CCD 2 TEXT 1 TEXT 2

FUNCTION

BLUE BACK

HALFTONE

CCD

OFF

OFF

OFF

FUNCTION

BLUE BACK

HALFTONE

CCD or

: MOVE : ADJ.

: PREV.

OFF

OFF

CCD1

: MOVE : ADJ.

: PREV.

33

OTHER USEFUL FUNCTIONS

QUICK VIEW Button :

Press QUICK VIEW button on the Remote Control. The previously viewed channel will appear on the screen. Press QUICK VIEW again to switch back to the original channel.

Repeatedly pressing QUICK VIEW switches between these two channel.

DISPLAY BUTTON :

Press DISPLAY button on the Remote Control The channel number of the program you are now viewing, the current time and sleep time setting are displayed.

MUTE BUTTON :

Press MUTE button on the Remote Control. The volume of the TV program being viewed will be reduced to zero and "MUTE" will appear on the screen.

NOTE : Changing the audio volume also restores the sound.

34

DVD FUNCTION & OPERATION

INTRODUCTION

Manufactured under license from Dolby Laboratories.

"Dolby" and the double-D symbol are trademarks of Dolby Laboratories.

35 36

Disc Requirements/Copyright Information

37

Remote Control Unit (DVD)

1. OPEN/CLOSE BUTTON

Use this button to open/close the disc tray.

Pressing this button will while on TV/Video mode will automatically change it to DVD mode.

2. PLAY/PAUSE BUTTON

Use this button to play or pause the disc. Pressing this button during play, cause the disc pause if in pause mode it function as the play.

Pressing this button will while on TV/Video mode will automatically change it to DVD mode.

3. STOP BUTTON

Use this button to stop the current playing mode.

4. SETUP BUTTON

Use this button to setup the various operation information of this unit to customize DVD performance.

5. FF/SF BUTTON

Use this button to play the disc fast forward or slow forward. During pause or step state, the button work as slow forward.

6. FR/SR BUTTON

Use this button to play the disc fast reverse or slow reverse. During pause or step state, the button work as slow reverse.

7. NEXT BUTTON

Use this button to move to the next chapter (DVD).

8. PREV BUTTON

Use this button to move to the previous chapter (DVD).

9. MENU BUTTON

Use this button to display the contents menu of the loaded DVD disc. This function is disc dependent. A DVD disc may not contain a contents menu.

10. STEP BUTTON

Use this button to play one frame at a time.

11. SUBTITLE BUTTON

Use this button to change the subtitle language to a different language or from the one selected at the initial settings. When the loaded disc support multiple subtitle.

38

Remote Control Unit (DVD)

12. ANGLE BUTTON

If a disc includes multi angle information, the user can watch a screen in multi angles. The function is limited to a DVD disc supporting multi angle information.

13. ZOOM BUTTON

Use this button to enlarge DVD or DVD screen image up to 4 times. You may also move the image using CH , buttons.

14. TITLE BUTTON

Use this button to display the title menu of the loaded DVD disc. This function is disc dependent. A DVD disc may not contain a contents menu.

15. 3D BUTTON

Use this button for stereophonic sound system.

16. AUDIO BUTTON

Use this button to change the audio language to a different language from the one selected at the initial settings, when the loaded disc supports multiple audio language.

17. REPEAT BUTTON

Use this button to set up repeat viewing during play, for repeated playback of disc titles, to repeat the selected segment, or for specifying and repeating playback of a chapters or sound.

Basic Playback

39 40

Searching for a specific screen/song during playback Searching for a specific screen/song during playback

41 42

Setting a custom view Changing the audio/subtitle language

43 44

Changing the size and angle of the screen Selecting a menu and 3D

45 46

Using the Setup Menu Setting the Language

47 48

Setting the Language Setting the VIDEO

49 50

Setting the SPEAKERS Setting the Audio

51 52

CUSTOM settings Setting rating level and password

53 54

Operation with an MP3 disc Operation with an MP3 disc

C:001 / T:008

55 56

Use of JPEG DISC Use of JPEG DISC

57 58

TROUBLE SHOOTING GUIDE

TV

Before requesting service, please refer to the following chart for the symptom and possible solution. For more information, see the corresponding page in this manual.

SYMPTOM

TV does not operate

Poor sound or no sound

Poor picture or no picture

Poor reception on some channels.

Poor color or no color

Picture wobbles or drifts

No CATV reception

Horizontal or diagonal bars on screen

No reception above

Channel 13

No remote operation

TV shuts off

POSSIBLE SOLUTIONS

Make sure the power cord is plugged in.

Try another AC outlet.

Power is off, check fuse or circuit breaker.

Station or CATV experiencing problems, turn to another station.

Check sound adjustments (Volume and Mute).

Check for sources of possible interference.

Station or CATV experiencing problems, turn to another station.

Check antenna or CATV connections, reorient antenna.

Check for sources of possible interference.

Check picture control adjustments.

Station or CATV experiencing problems, turn to another station.

Station signal is weak, reorient antenna to receive a strong signal.

Check for sources of possible interference.

Station or CATV experiencing problems, turn to another station.

Make sure channels are set into memory.

Check picture control adjustments.

Make sure TV/CATV Mode is in the correct position.

Check antenna or CATV connections, reorient antenna.

Check for sources of possible interference.

Station or CATV experiencing problems, turn to another station.

Make sure channels are set into memory.

CATV company is scrambling signal.

Check antenna connections and reorient antenna.

Check CATV connections

Make sure TV/CATV is in the correct position.

Station or CATV system problems,try another station.

Check antenna connections and reorient antenna.

Make sure TV/CATV Mode in the correct position.

Check for sources of possible interference.

Make sure TV/CATV Mode is in the correct position.

If using antenna, check UHF antenna connections.

Batteries are weak, dead, or inserted improperly.

Remote is out of range, move closer to TV.

Make sure remote is aimed at sensor.

Confirm there are no obstructions between the remote and the TV.

Make sure the power cord is plugged in.

Power interrupted.

Sleep Timer , On Timer or Off Timer are set; Station has stopped broadcasting.

59

DVD

60

SPECIFICATION

TV

DVD

Power Source

TV Broadcasting

Receiving Channels

Channel indicator

Sound Output

Speakers

Dimension (W H D)

Weight

Video Output

Audio Output

AC 120V~, 60Hz, 60W

DC 12-24V, 54W

NTSC

VHF 2-13CH, UHF 14-69CH

CATV 1, 14 - 125CH (T/T 181CH)

On Screen Display

1.5W+1.5W (Stereo)

3W(8ohm) x 2 (Stereo)

273mm (W) x 318mm (H) x 318mm (D)

8.4Kg

1.0Vp-p, 75 unbalanced

2.0Vrms (at 1KHz)

61

INTERFERENCE CAUSES

The most up-to-date technology to eliminate an interference is incorporated in your television receiver. Local conditions, however, can create the disturbances which visibly affect your picture. Proper installation, good antenna connection and following advice of your dealer are your best safeguards against the following disturbances.

The most common type of television disturbances are as follows:

IGNITION

Black spots or horizontal streaks may appear, picture may flutter or drift. Usually caused by interference from automobile ignition system, neon lamps, electrical drills and other electrical appliances.

GHOSTING

Ghostings are caused by the television signal following two paths. One is the direct path and the other is reflected from tall buildings, hills or some other objects. Changing the direction or position of the antenna may improve the reception.

SNOW lf your receiver is located at the fringe area of a television station where the signal is weak, your picture may be blurred by the appearance of small dots. When the signal is extremely weak, it may be necessary to install a special antenna to improve the picture.

RADIO FREQUENCY INTERFERENCE

The interference produces moving ripples or diagonal streaks, and in some cases, causes the loss of the contrast in picture.

62

MEMO

63 64

MEMO

65

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals