Delfield 536-SR68 User's Manual

Delfield 536-SR68 User's Manual
Delfield
™
®
536-SR68 & 536-SRR68 Dual View Display Case
Service, Installation and Care Manual
Please read this manual completely before attempting to install or operate this equipment! Notify carrier
of damage! Inspect all components immediately. See page 2.
536-SR68
TION
A
M
R
O
T INF
N
A
T
R
O
USE
IMP
E
R
O
F
E
ONS!
I
T
C
READ B
U
R
INST
E
S
E
H
T
AVE
S
E
S
A
E
Effective Date June 2008
PL
Dual View Series Service and Installation Manual
Serial Number Location
Contents
Serial Number Location . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Receiving and Inspecting the Equipment . . . . . . . . . . . . 2
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Display Case Glass Replacement . . . . . . . . . . . . . . . . . . 3
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Pressure Control Settings . . . . . . . . . . . . . . . . . . . . . . . . 5
Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Replacement Parts Lists . . . . . . . . . . . . . . . . . . . . . . . . . 6
Standard Warranties . . . . . . . . . . . . . . . . . . . . . . . . . . 7-9
The serial number is located on the rear of the unit on the
bottom right hand side.
Always have the serial number available when calling for
parts or service.
©2008 The Delfield Company. All rights reserved. Reproduction
without written permission is prohibited. “Delfield” is a registered
trademark of The Delfield Company.
Receiving And Inspecting The Equipment
Even though most equipment is shipped crated, care should
be taken during unloading so the equipment is not damaged
while being moved into the building.
1. Visually inspect the exterior of the package and skid or
container. Any damage should be noted and reported to
the delivering carrier immediately.
2. If damaged, open and inspect the contents with the
carrier.
3. In the event that the exterior is not damaged, yet upon
opening, there is concealed damage to the equipment
notify the carrier. Notification should be made verbally as
well as in written form.
4. Request an inspection by the shipping company of the
damaged equipment. This should be done within 10 days
from receipt of the equipment.
5. Also open the compressor compartment housing and
visually inspect the refrigeration package. Be sure lines
are secure and base is still intact.
6. Freight carriers can supply the necessary damage forms
upon request.
7. Retain all crating material until an inspection has been
made or waived.
Uncrating the Equipment
First cut and remove the banding from around the crate.
Remove the front of the crate material, use of some tools will
be required.
Warning: While uncrating do not lay unit on side.
If compressor is set on side, return to upright
position for 24 hours to allow for all compressor
oil to drain back into compressor.
Specifications
Model
Length
Overall
Depth
Height
536-SR68
36”
28”
68”
(91.4cm) (71.1cm) (172.7cm)
536-SRR68
36”
28”
68”
(91.4cm) (71.1cm) (172.7cm)
Shelf
Area
19.9ft2
Storage
Capacity
21.8ft3
Design
Load
H.P.
Volts
Amps
NEMA
Plug
Ship Weight
1286
1/2
120
12.0
5-15P
600lbs/272kg
19.9ft2
21.8ft3
1286
N/A
120
5.0
N/A
575lbs/261kg
Delfield
™
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
®
Dual View Series Service and Installation Manual
Installation
Location
These units are intended for indoor use only. Be sure the
location chosen has a floor strong enough to support 1000
pounds of the cabinet and contents. Reinforce the floor as
necessary to provide for maximum loading.
For the most efficient refrigeration, be sure to provide good
air circulation inside and out.
Inside cabinet: Do not pack refrigerator so full that air
cannot circulate.
Outside cabinet: Be sure that the unit has access to ample
air. Avoid hot corners and locations near stoves and ovens.
Leveling
A level cabinet looks better and will perform better because:
1. The drain pan will drain properly.
2. The doors will line up with the frames properly.
3. The cabinet will not be subject to undue strain.
To meet NSF standards, this unit must be sealed to the
floor.
Installation of glass shelves
1. Remove stainless steel shelf bracket assemblies by
sliding key slots over shoulder bolts on inside edges of
posts.
2. Plug light cords into receptacles.
3. Place 0.25” safety glass shelves on brackets.
Installation of dry section front & side glass
1. Remove (2) acorn nuts on bottom side of shelf.
2. Remove top of stainless steel shelf by lifting shelf off
subtop.
3. Place 0.25” thick side glass pieces into bottom channel
and lower rear of stainless steel shelf.
4. Place 0.25” thick front glass piece into bottom channel
and lower front of stainless steel shelf over top edge of
glass.
5. Replace acorn nuts on bottom side of shelf.
Plumbing
Self-contained models are standard with a condensate
evaporator. If the evaporator fails, the unit’s drain must have
an outlet to an appropriate drainage area or container.
CAUTION
Moisture collecting from improper drainage
can create a slippery surface on the floor
and a hazard to employees. It is the owner’s
responsibility to provide a container or outlet for
drainage.
Electrical connection
Refer to the wattage data on page 2, the serial tag and your
local code to be sure the unit is connected to the proper
power source. A protected circuit of the correct voltage
and amperage must run for connection of the line cord, or
permanent connection to the unit.
Self-contained units have an ON/OFF switch located in the base
of the unit. Simply turn the switch to ON to begin operation.
The power switch must be turned OFF and
the unit disconnected from the power source
whenever performing service or maintenance
functions.
Operation Information
On self-contained models, after turning the ON/OFF switch
to ON, the unit’s compressor will begin operating. Delfield
display cases are designed to maintain an operation
temperature of 36°F to 40°F at ambient room temperature of
75°F and relative humidity of 55%.
Do not load the storage area in a way that restricts the air
flow. Overloading will result in a loss of temperature.
Continuous opening and closing of the doors will hamper
the units ability to maintain operational temperature.
Display Case Glass Replacement
Delfield professionally packages the glass in the crate
to minimize the risk of freight damage. However, during
shipment glass damage can happen and breakage is not
covered under warranty. If your Delfield unit arrives with
broken glass in the top dry section, we recommend that you
purchase replacement glass locally. The table to the right lists
replacement sizes for the dry top section only.
Please call your Delfield service or sales representative if you
have any questions on glass replacement.
Delfield
™
Shelves
(Top)
34.0” x 15.84”
(Center)
34.0” x 17.24”
(Bottom)
32.50” x 15.43”
Front
24.95” x 35.0”
Sides
Two Each Required:
24.57” tall;
19.38” at bottom
15.04” at top
*** All glass shelving is .25” thick safety glass.***
®
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
Dual View Series Service and Installation Manual
Maintenance
Door Gasket Maintenance
Door gaskets require regular cleaning to prevent mold and mildew
build up and also to retain the elasticity of the gasket. Gasket cleaning
can be done with the use of warm soapy water. Avoid full strength
cleaning products on gaskets as this can cause them to become brittle
and crack. Never use sharp tools or knives to scrape or clean the
gasket. Gaskets can be easily replaced and do not require the use of
tools or an authorized service person. The gaskets are “Dart” style and
can be pulled out of the groove in the door and new gaskets can be
“pressed” back into place.
Caster Maintenance
Wipe casters with a damp cloth monthly to prevent corrosion.
The power switch must be turned to OFF and the
unit disconnected from the power source whenever
performing service, maintenance functions or cleaning
the refrigerated area.
Refrigerators and Freezers
The interior and exterior can be cleaned using soap and warm water.
If this isn’t sufficient, try ammonia and water or a nonabrasive liquid
cleaner. When cleaning the exterior, always rub with the “grain” of
the stainless steel to avoid marring the finish. Do not use an abrasive
cleaner because it will scratch the stainless steel and can damage the
breaker strips and gaskets.
Stainless Steel Care and Cleaning
To prevent discoloration or rust on stainless steel several important
steps need to be taken. First, we need to understand the properties of
stainless steel. Stainless steel contains 70- 80% iron, which will rust.
It also contains 12-30% chromium, which forms an invisible passive
film over the steel’s surface, which acts as a shield against corrosion.
As long as the protective layer is intact, the metal is still stainless.
If the film is broken or contaminated, outside elements can begin to
breakdown the steel and begin to form discoloration or rust. Proper
cleaning of stainless steel requires soft cloths or plastic scouring
pads.
NEVER USE STEEL PADS, WIRE BRUSHES OR SCRAPERS!
Cleaning solutions need to be alkaline based or non-chloride cleaners.
Any cleaner containing chlorides will damage the protective film of
the stainless steel. Chlorides are also commonly found in hard water,
salts, and household and industrial cleaners. If cleaners containing
chlorides are used be sure to rinse repeatedly and dry thoroughly.
Routine cleaning of stainless steel can be done with soap and water.
Extreme stains or grease should be cleaned with a non-abrasive
cleaner and plastic scrub pad. Always rub with the grain of the
steel. There are stainless steel cleaners available which can restore
and preserve the finish of the steels protective layer. Early signs of
stainless steel breakdown are small pits and cracks. If this has begun,
clean thoroughly and start to apply stainless steel cleaners in attempt
to restore the passivity of the steel.
Never use an acid based cleaning solution! Many food
products have an acidic content, which can deteriorate the
finish. Be sure to clean the stainless steel surfaces of ALL
food products. Common items include, tomatoes, peppers
and other vegetables.
Cleaning the Condenser Coil
In order to maintain proper refrigeration performance, the condenser
fins must be cleaned of dust, dirt and grease regularly. It is recommended
that this be done at least every three months. If conditions are such
that the condenser is totally blocked in three months, the frequency
of cleaning should be increased. Clean the condenser with a vacuum
cleaner or stiff brush. If extremely dirty, a commercially available
condenser cleaner may be required.
Failure to maintain a clean condenser coil can initially cause high
temperatures and excessive run times. Continuous operation with
a dirty or clogged condenser coil can result in compressor failure.
Neglecting the condenser coil cleaning procedures will void any
warranties associated with the compressor and cost to replace the
compressor.
Never use a high-pressure water wash for this cleaning
procedure as water can damage the electrical components
located near or at the condenser coil.
Doors/Hinges
Over time and with heavy use doors the hinges may become loose. If
this happens tighten the screws that mount the hinge brackets to the
frame of the unit. Loose or sagging doors can cause the hinges to pull
out of the frame, which may damage both the doors and the hinges. In
some cases this may require qualified service agents or maintenance
personnel to perform repairs.
Do not place hot pans on/against the blue ABS liner. Do not
throw items into the storage area. Failure to follow these
recommendations could result in damage to the interior of
the cabinet or to the blower coil. Overloading the storage
area, restricting the airflow, and continuous opening and
closing of the doors and drawers will hamper the units
ability to maintain operational temperature.
Preventing blower coil corrosion
To help prevent corrosion of the blower coil, store all acidic items,
such as pickles and tomatoes, in sealable containers. Immediately
wipe up all spills.
Units with pans should be operated with pans in place.
Operating the unit without all pans in place will lower
efficiency and may damage the unit.
Continuous opening and closing of the doors will hamper the unit’s
ability to maintain optimum refrigeration temperature. Top section is
not intended for overnight storage. Product should be removed from
pans. Pans can remain in unit while empty.
Cleaning the condensate evaporator (remote models only)
The stainless steel condensate evaporator pan should be cleaned
every six months. Use a vacuum cleaner or damp cloth to remove
dust that may have accumulated. This will prevent corrosion of the
stainless steel.
Delfield
™
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
®
Dual View Series Service and Installation Manual
Pressure Control Settings
The temperature is controlled by an adjustable pressure
control located in the machine compartment. An
adjustable control has the word COLDER near the knob,
with an arrow to indicate the adjustment direction. These
controls are field adjustable and do not require a service
agent. If you have any questions, feel free to contact the
Delfield Service Department.
The refrigeration system on self-contained models was
adjusted at the factory to maintain between 36°F and
40°F. No adjustment should be necessary. If adjustment
does become needed, however, the factory recommended
settings are:
Operating pressure: 80 psi cut-in, 50 psi cut-out, 30 psi
differential.
Display Case Condensation And Temperature Adjustment
If your Delfield unit has excessive condensation on the
refrigerated glass, the temperature should be adjusted to
maintain 41° to minimize condensation.
There is a hanging thermometer in the refrigerated section.
Please note that the adjustment needed is very small
and it will take the case 24 hours to equilibrate after the
adjustment is made.
Wiring Diagram
536-SR68
L1
N
G
S1
PS1
CONDENSING UNIT
COOLING FANS
CONDENSATE EVAPORATOR
S2
Remote Units Only
BALLAST
BALLAST
BALLAST
Delfield
™
FLUORESCENT LIGHTS
®
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
Dual View Series Service and Installation Manual
Replacement Parts
Description
Adjustable foot leveler
Alum. light with 6” cord
Alum. light ext with 6” cord
Alum. light ext with 15” cord
Alum. light ext with 17” cord
Angled coil assy. cover
Box and ballast assy.
Button bumper
Compressor
Cord/plug assy.
Danfoss Condenser Kit
Part#
3234696
2194523
2194526
2194524
2194525
226-A12-Z0004
2194522
9291179
3526752
2183347
2194753KT
Door catch magnet bracket
Dry 24.95 x 35.00 glass front
Dry 24.75 x 19.38 glass side
Dry door plate mount LT
Dry door plate mount RT
Evaporator coil
Evaporator fan motor
Expansion valve
Fan motor blower coil bracket
Filter dryer
Glass shelf 15.43 x 32.50
Glass shelf - bottom dry
Glass shelf - top dry
Lexan fan blade
Lexan fan guard
Louver access front s/s
Louvered panel access
Magnetic snap in catch
*Pike door and frame assy.
*Pike door dry hinged set
Plastic drain
Rocker switch
Screw #8
264-052-Z000D
3455355
3455357
264-AYK-Z000E
264-AYK-Z000F
3510086
2162691
3516273
031-264-0000
3516101
3544342
3455341
3455340
3516172
3516173
311-411-Z0005
312-411-Z0004
3234156
3234299
3234300
3234242
2190154
9321137
Includes control, display knobs, and probe
*Special order item. Allow for longer delivery time.
Delfield
™
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
®
Dual View Series Service and Installation Manual
Standard Labor Guidelines To Repair Or Replace Parts On Delfield Equipment
Advice and recommendations given by Delfield Service Technicians do not constitute or guarantee any special coverage.
•A maximum of 1-hour is allowed to diagnose a defective component.
•A maximum of 1-hour is allowed for retrieval of parts not in stock.
•A maximum travel distance of 100 miles round trip and 2-hours will be reimbursed.
•Overtime, installation/start-up, normal control adjustments, general maintenance, glass breakage, freight damage, and/or
correcting and end-user installation error will not be reimbursed under warranty unless pre-approved with a Service Work
Authorization from Delfield. You must submit the number with the service claim.
LABOR OF 1-HOUR IS ALLOWED TO REPLACE:
•Circulating Fan Motor and Blade
•Compressor Start Components and Overload Protector
•Condensate Element
•Door Hinges, Locks, and Gaskets
•Evaporator/Condenser Fan Motor and Blade
LABOR OF 2 HOURS TO REPLACE:
•Heating Element
•Locate/Repair Leak
•Pressure Control
LABOR OF 3 HOURS TO REPLACE:
•Condenser or Evaporator Coil
•Expansion Valve
LABOR OF 4 HOURS TO REPLACE:
•Compressor
This includes recovery of refrigerant and leak check.
$55.00 maximum reimbursement for refrigerant recovery (includes recovery machine, pump, torch, oil, flux, minor fittings,
solder, brazing rod, nitrogen, or similar fees.)
REFRIGERANTS
•R404A A maximum of $15.00/lb. or &1.00/oz. will be reimbursed.
Delfield
™
®
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
Dual View Series Service and Installation Manual
Standard One Year Warranty (One year parts, 90 days labor.)
The Delfield Company (“Delfield”) warrants to the Original Purchaser
of the Delfield product (herein called the “Unit”) that such Unit, and all
parts thereof, will be free from defects in material and workmanship
under normal use and service for a period of one (1) year from the
date of shipment of the Unit to the Original Purchaser or, if the
Original Purchaser returns the warranty card completely filled out
including the date of installation within thirty (30) days of receipt
of the Unit, one (1) year from the date of installation. During this
one year warranty period, Delfield will repair or replace any defective
part or portion there of returned to Delfield by the Original Purchaser
which Delfield determines was defective due to faulty material or
workmanship. The Original purchaser will pay all labor, crating, freight
and related costs incurred in the removal of the Unit of defective
component and shipment to Delfield, except that during a period of
either ninety (90) days from the date of shipment of the Unit to the
Original Purchaser or, if the Original Purchaser returns the warranty
card completely filled out including the date of installation within thirty
(30) days of receipt of the Unit, ninety (90) days from the date of
installation Delfield will pay all related labor costs. Delfield will pay the
return costs if the Unit or part thereof was defective.
The term “Original Purchaser” as used herein means that person, firm,
association, or corporation for whom the Unit was originally installed.
This warranty does not apply to any Unit or part thereof that has
been subjected to misuse, neglect, alteration, or accident, such as
accidental damage to the exterior finish, operated contrary to the
recommendations specified by Delfield; or repaired or altered by
anyone other than Delfield in any way so as to, in Delfield’s sole
judgement, affect its quality or efficiency. This warranty does not
apply to any Unit that has been moved from the location where it was
originally installed. This warranty also does not cover the refrigerator
drier or the light bulbs used in the Unit. The warranty is subject to
the user’s normal maintenance and care responsibility as set
forth in the Service and Installation Manual, such as cleaning the
condenser coil, and is in lieu of all other obligations of Delfield.
Delfield neither assumes, nor authorizes any other person
to assume for Delfield, any other liability in connection with
Delfield’s products.
Removal or defacement of the original Serial Number or Model
Number from any Unit shall be deemed to release Delfield from all
obligations hereunder or any other obligations, express or implied.
Parts furnished by suppliers to Delfield are guaranteed by Delfield
only to the extent of the original manufacturer’s express warranty
to Delfield. Failure of the Original Purchaser to receive such
manufacturer’s express warranty to Delfield. Failure of the Original
Purchaser to receive such manufacturers warranty shall in no way
create any warranty, expressed or implied, or any other obligation or
liability on Delfield’s part in respect thereof.
IF THE CUSTOMER IS USING A PART THAT RESULTS IN
A VOIDED WARRANTY AND A DELFIELD AUTHORIZED
REPRESENTATIVE TRAVELS TO THE INSTALLATION
ADDRESS TO PERFORM WARRANTY SERVICE, THE SERVICE
REPRESENTATIVE WILL ADVISE CUSTOMER THE WARRANTY IS
VOID. SUCH SERVICE CALLS WILL BE BILLED TO CUSTOMER
AT THE AUTHORIZED SERVICE CENTER’S THEN APPLICABLE
TIME AND MATERIALS RATES. CONSIDER: CUSTOMER MAY
INITIATE A SERVICE AGREEMENT WITHOUT PARTS COVERAGE.
If shipment of a replacement part is requested prior to the arrival in
the Delfield factory of the part claimed to be defective, the Original
Purchaser must accept delivery of the replacement part of a C.O.D.
basis, with credit being issued after the part has been received and
inspected at Delfield’s plant and determined by Delfield to be within
this warranty.
Under no condition does this warranty give the Original Purchaser
the right to replace the defective Unit with a complete Unit of the
same manufacturer or of another make. Unless authorized by
Delfield in writing, this warranty does not permit the replacement of
any part, including the motor-compressor, to be made with the part
of another make or manufacturer.
No claims can be made under this warranty for spoilage of any
products for any reason, including system failure.
The installation contractor shall be responsible for building access,
entrance and field conditions to insure sufficient clearance to allow
any hood(s), vent(s), or Unit(s) if necessary, to be brought into the
building. Delfield will not be responsible for structural changes or
damages incurred during installation of the Unit or any exhaust
system.
Delfield shall not be liable in any manner for any default or delay in
performance hereunder caused by or resulting from any contingency
beyond Delfield’s control, including, but not limited to, war,
governmental restrictions or restraints, strike, lockouts, injunctions,
fire, flood, acts of nature, short or reduced supply of raw materials,
or discontinuance of the parts by the original part manufacturer.
Except as provided in any Additional Four Year Protection
Plan, if applicable, and the Service Labor Contract, if
applicable, the foregoing is exclusive and in lieu of all other
warranties, whether written or oral, express or implied. This
warranty supersedes and excludes any prior oral or written
representations or warranties. Delfield expressly disclaims any
implied warranties of merchantability, fitness for a particular
purpose of compliance with any law, treaty, rule or regulation
relating to the discharge of substances into the environment.
The sole and exclusive remedies of any person relating to
the Unit, and the full liability of Delfield for any breach of this
warranty, will be as provided in this warranty.
Other than this Delfield Standard One Year Limited Warranty, any
applicable Delfield Additional Four Year Protection Plan or applicable
Delfield Service Labor Contract, the Original Purchaser agrees and
acknowledges that no other warranties are offered or provided in
connection with or for the unit or any other part thereof.
In no event will Delfield be liable for special, incidental or
consequential damages, or for damages in the nature of penalties.
IF DURING THE WARRANTY PERIOD, CUSTOMER USES
A PART FOR THIS DELFIELD EQUIPMENT OTHER THAN
AN UNMODIFIED NEW OR RECYCLED PART PURCHASED
DIRECTLY FROM DELFIELD OR ANY OF ITS AUTHORIZED
SERVICE CENTERS AND/OR THE PART BEING USED IS
MODIFIED FROM ITS ORIGINAL CONFIGURATION, THIS
WARRANTY WILL BE VOID. FURTHER, DELFIELD AND
ITS AFFILIATES WILL NOT BE LIABLE FOR ANY CLAIMS
DAMAGES OR EXPENSES INCURRED BY THE CUSTOMER
WHICH ARISE DIRECTLY OR INDIRECTLY, IN WHOLE OR IN
PART, DUE TO THE INSTALLATION OF ANY MODIFIED PART
AND/OR PART RECEIVED FROM AN UNAUTHORIZED SERVICE
CENTER. If the warranty becomes void, Customer may
purchase from Delfield, if available, a Service Agreement or
service at the then current time and materials rate.
For more information on Delfield warranty’s log on and check out the
service section of our web site at www.delfield.com.
Delfield
™
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
®
Dual View Series Service and Installation Manual
Additional Four Year Protection Plan
Delfield Model# Serial #
(for Motor-Compressor only)
Installation
Date
Replacement of a defective Motor-Compressor is limited to one (1)
Motor-Compressor by us during the four (4) year period. Delfield shall
replace the Motor-Compressor at no charge.
In addition to the Standard One Year Warranty on the MotorCompressor contained in the above listed Delfield product (the
“Unit”), The Delfield Company (“Delfield”) also agrees to repair, or
exchange with similar or interchangeable parts in design and capacity
at Delfield’s option, the defective Motor-Compressor contained in the
Unit (the “Motor-Compressor), or any part thereof, for the Original
Purchaser only, at any time during the four (4) years following the
initial one (1) year period commencing on the date of installation
for the Original Purchaser. Failure of the Original Purchaser to
register the registration card containing the Original Purchasers
name, address, date of installation, model number and serial
number of the Unit containing the Motor-Compressor within
30 days from the date of installation shall void this warranty.
This additional warranty is only available if the Motor-Compressor
is inoperative due to defects in material or factory workmanship, as
determined by Delfield in its sole judgement and discretion. The
Original Purchaser shall be responsible for returning the defective
Motor-Compressor to Delfield prepaid, F.O.B. at the address shown on
the back cover of this manual.
The term “Original Purchaser” as used herein means that person, firm,
association, or corporation for whom the Unit was originally installed.
The term “Motor-Compressor” as used herein does not include unit
base, air or water cooled condenser, receiver, electrical accessories
such as relay, capacitors, refrigerant controls, or condenser fan/motor
assembly. This warranty does not cover labor charges incidental to
the replacement of parts. This warranty further does not include
any equipment to which said condensing unit is connected, such as
cooling coils, temperature controls or refrigerant metering devices.
This warranty shall be void if the Motor-Compressor, in Delfield’s
sole judgement, has been subjected to misuse, neglect, alteration
or accident, operated contrary to the recommendations specified
by the Unit manufacturer, repaired or altered by anyone other than
Delfield in any way so as, in Delfield’s sole judgment, to affect its
quality or efficiency or if the serial number has been altered, defaced
or removed. This Warranty does not apply to a Motor-Compressor in
any Unit that has been moved from the location where it was originally
installed. The addition of methyl chloride to the condensing unit or
refrigeration system shall void this warranty.
General Conditions
Delfield shall not be liable in any manner for any default or delay in
performance hereunder caused by or resulting from any contingency
beyond Delfield’s control, including, but not limited to, war,
governmental restrictions or restraints, strike, lockouts, injunctions,
fire, flood, acts of nature, short or reduced supply of raw materials,
or discontinuance of any part or the Motor-Compressor by the unit
manufacturer.
Delfield
™
This warranty does not give the Original Purchaser of the MotorCompressor the right to purchase a complete replacement MotorCompressor of the same make or of another make. It further does
not permit the replacement to be made with a Motor-Compressor
of another kind unless authorized by Delfield. In the event Delfield
authorizes the Original Purchaser to purchase a replacement MotorCompressor locally, only the wholesale cost of the Motor-Compressor
is refundable.
Expressly excluded from this warranty are damages resulting from
spoilage of goods.
Except as provided in any applicable Standard One Year Limited
Warranty or applicable Service Labor Contract, the foregoing is
exclusive and in lieu of all other warranties, whether written or
oral, express or implied. This Warranty supersedes and excludes
any prior oral or written representations or warranties. Delfield
expressly disclaims any implied warranties of merchantability,
fitness for a particular purpose or compliance with any law,
treaty, rule or regulation relating to the Motor-Compressor, and
the full liability of Delfield for any breach of this warranty, will be
as provided in this warranty.
Other than any applicable Delfield Standard One year Limited
Warranty, this Delfield Additional Four Year Protection Plan and any
applicable Delfield Service Labor Contract, the Original Purchaser
agrees and acknowledges that no other warranties are offered or
provided in connection with or for the Motor-Compressor or any part
thereof.
In no event will Delfield be liable for special, incidental or
consequential damages, or for damages in the nature of penalties.
®
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
Dual View Series Service and Installation Manual
Notes:
Delfield
™
10
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
®
Dual View Series Service and Installation Manual
notes:
Delfield
™
®
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
11
Covington, TN
Mt. Pleasant, MI
Thank you for choosing Delfield!
Help is a phone call away. Help our team of professional, courteous
customer service reps by having your model number and serial number
available at the time of your call (800) 733-8829.
Model:_____________________ S/N: ____________________
Installation Date:_____________
For a list of Delfield’s authorized parts depots,
visit our website at www.delfield.com.
980 S. Isabella Rd., Mt. Pleasant, MI 48858, U.S.A. • (989) 773-7981 or (800) 733-8829 • Fax (989) 773-3210 • www.delfield.com
Delfield reserves the right to make changes in design or specifications without prior notice. ©2008 The Delfield Company. All rights reserved. Printed in the U.S.A.
DMDUAL 06/08
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement