Installer Guide

Add to My manuals
16 Pages

advertisement

Installer Guide | Manualzz

®

Installer Guide

TM

Universal Programmable Smart Wi-Fi Thermostat

7320 Up to 3 Heat / 2 Cool Heat Pump

Up to 2 Heat / 2 Cool Conventional

with wireless Humidity Control*

Model number is located on back of thermostat.

See Wi-Fi Setup Guide for Wi-Fi Setup Instructions

1

Specifications 2 Installation and Wiring 3 Quick Reference

4 Installer Settings 5 Wireless Remote Sensors 6 System Testing

Attention

To prevent damage to the thermostat, never use a sharp instrument to press the touchscreen keys. Always press keys with your fingers.

Warning

For installation by experienced service technicians only.

Caution

• Possible electric shock or damage to equipment can occur.

• Disconnect power before beginning installation.

This thermostat requires 24 Volt AC Power or 2 properly installed “AA” Alkaline batteries for proper operation. If connecting this thermostat to a Wi-Fi network,

a 24 VAC common (C wire) is required.

For use only as described in this manual. Any other use will void warranty.

1 Specifications

This thermostat is compatible with:

• Single stage heat / cool conventional and heat pump systems

• Conventional systems up to 2 stages of heating and 2 stages of cooling

• Heat pump systems up to 3 stages of heating and 2 stages of cooling

Electrical and control specifications:

• Electrical Rating: 24 Volt AC

• 1 amp maximum load per terminal, 6 amp maximum load

• AC Power: 18 – 30 Volts AC

• DC Power: 3.0 Volt DC (2 “AA” Alkaline Batteries Included)

• Control Range: 45° – 90° F (7° – 32° C)

• Temperature Accuracy: +/- 1° F (+/- .5° C)

• Outdoor Temperature Display Range: -40° - 120° F (-40° - 49° C)

Terminations:

Rc, Rh, C, W2/AUX, W1/E, L, A, O/B, G, Y2, Y1, K, S2, S1

* Wireless Humidity Control requires accessory model 7330.

7320-100-01

2 Installation and Wiring

Warning

Disconnect power before beginning installation.

Thermostat Location

Install the thermostat approximately 5 feet (1.5m) above the floor in an area that has a good amount of air circulation and maintains an average room temperature.

Avoid installation in locations where the thermostat can be affected by drafts, dead air spots, hot or cold air ducts, sunlight, appliances, concealed pipes, chimneys and outside walls.

Install your new Braeburn thermostat in 4 basic steps:

1 Install the Sub-Base

2 Provide Power

3 Connect Your Wires

4 Attach Thermostat to Sub-Base

• Remove the sub-base from the body of the thermostat.

• Mount the sub-base as shown below:

Drill 3/16” pilot holes in your desired location. Use supplied anchors for drywall or plaster.

UP UP

Installer Guide 2

Provide Power

+

C

+

24VAC Power Terminal (C)

Batteries Installed as Shown

For 24 Volt AC power, you must connect the common side of the transformer to the C terminal on the thermostat

sub-base. In dual transformer installations, the transformer common must come from the cooling transformer.

• For battery power, insert the 2 supplied “AA” type alkaline batteries into the battery compartment located in the rear

housing of the thermostat. Make sure to position the Positive (+) and Negative (-) sides of the batteries correctly with

the +/- symbols in the battery compartment.

• If connecting this thermostat to a Wi-Fi network, a 24 VAC common (C wire) is required.

Connect Your Wires

Terminal Function Description

Rc

Rh

Input

Input

24 Volt AC Cooling Transformer

(Dual Transformer Systems Only)

Power Connection (24 Volt AC

Heating Transformer)

G

Y2

Y1

K

S2

S1

C

W2 / AUX

W1 / E

L

A

O / B

Input

Output

Output

Input

Output

Output

Output

Output

Output

-

Input

24 Volt AC Transformer Common

(W2) 2nd Stage Conventional Heat

(AUX) Auxiliary Heat (Heat Pump)

(W1) 1st Stage Conventional Heat

(E) Emergency Heat

System Malfunction Indicator

Economizer, Fresh Air or Output Control

(O) Cool Active Reversing Valve

(B) Heat Active Reversing Valve

Fan Control

2nd Stage Compressor

1st Stage Compressor

Optional Share-a-Wire

TM module connection

Optional Wired Remote Sensor

(indoor or outdoor)

3 Installer Guide

Conventional Systems

Typical Wiring Configurations

NOTE: The “System Type” option will be configured in the Installer Settings section.

Heat Only

Set System Type to 11CONV

Rh 24 Volt AC Power

W1 Heat Relay

G Fan Relay [note 4]

C 24 Volt AC Transformer Common [note 1]

1 HEAT / 1 COOL Single or Dual Transformer

Set System Type to 11CONV

Rh 24 Volt AC Power (heating transformer) [note 2]

Rc 24 Volt AC Power (cooling transformer) [note 2]

W1 Heat Relay

Y1 Compressor Relay

G Fan Relay

C 24 Volt AC Transformer Common [note 1, 3]

2 HEAT / 2 COOL Single or Dual transformer

Set System Type to 22CONV

Rh 24 Volt AC Power (heating transformer) [note 2]

Rc 24 Volt AC Power (cooling transformer) [note 2]

W1 Heat Relay Stage 1

W2 Heat Relay Stage 2

Y1 Compressor Relay Stage 1

Y2 Compressor Relay Stage 2 [note 4]

G Fan Relay

C 24 Volt AC Transformer Common [note 1, 3]

NOTES - Conventional Systems

[1] Optional 24 Volt AC common connection

(required for Wi-Fi).

[2] Remove factory installed jumper for dual transformer systems.

[3] In dual transformer systems, transformer common must come from cooling transformer.

[4] If needed for system.

Provide disconnect and overload protection as required.

Installer Guide 4

Heat Pump Systems

Typical Wiring Configurations

NOTE: The “System Type” option will be configured in the Installer Settings section.

1 HEAT / 1 COOL - No Auxiliary Heat

3 HEAT / 2 COOL – Including Auxiliary Heat

Set System Type to 11HP

Set System Type to 32HP

Rh 24 Volt AC Power

Rc Connected to Rh with supplied Jumper Wire

O/B Changeover Valve [note 2]

Y1 Compressor Relay

G Fan Relay

C 24 Volt AC Transformer Common [note 1]

2 HEAT / 2 COOL - No Auxiliary Heat

Set System Type to 32HP

Rh 24 Volt AC Power

Rc Connected to Rh with supplied Jumper Wire

O/B Changeover Valve [note 2]

Y1 Compressor 1 Relay (1st stage heating/cooling)

Y2 Compressor 2 Relay (2nd stage heating/cooling)

G Fan Relay

C 24 Volt AC Transformer Common [note 1]

L Optional System Fault Monitor

[note 4]

Rh

Rc

24 Volt AC Power

Connected to Rh with supplied Jumper Wire

O/B Changeover Valve

[note 2]

Y1 Compressor 1 Relay (1st stage heating/cooling)

Y2 Compressor 2 Relay (2nd stage heating/cooling)

AUX

Auxiliary Heat Relay (3rd stage heating)

[note 3]

E

G

Emergency Heat Relay

Fan Relay

[note 3]

C

L

24 Volt AC Transformer Common

[note 1]

Optional System Fault Monitor

[note 4]

NOTES - Heat Pump Systems

[1] Optional 24 Volt AC common connection

(required for Wi-Fi).

[2] O (cool active) or B (heat active) is selected in the Installer Settings menu.

[3] Install a field supplied jumper between the

W2/AUX and W1/E terminals if there is no separate emergency heat relay installed.

[4] If the L terminal is used, the 24 Volt AC common must be connected (C terminal).

Provide disconnect and overload protection as required.

2 HEAT / 1 COOL - Including Auxiliary Heat

Set System Type to 22HP

Rh 24 Volt AC Power

Rc Connected to Rh with supplied Jumper Wire

O/B Changeover Valve [note 2]

Y1 Compressor Relay (1st stage heating/cooling)

W2 Auxiliary Heat Relay (2nd stage heating) [note 3]

E Emergency Heat Relay

[note 3]

G Fan Relay

C 24 Volt AC Transformer Common [note 1]

L

Optional System Fault Monitor

[note 4]

5 Installer Guide

Additional Wiring Options - All System Types

NOTE: Additional options are configured in the

Installer Settings section.

S1

Indoor or Outdoor Remote Sensor

[note 1]

S2

A Economizer, Fresh Air or Output Control

K Share-a-Wire

TM

Module

[note 2]

NOTES - Additional Wiring Options

[1] Can be used to connect a Braeburn

® indoor or outdoor wired remote sensor.

[2] Can be used to share a wire on existing installations where a common connection (C wire) is required.

4

Attach Thermostat to Sub-Base

UP UP

L

W2/

AUX2

RH

RC

S1

A

H

Y1

Y2

INSTRUCTIONS

HUMID

1) Line up the thermostat body with the sub-base.

2) Carefully push the thermostat body against the sub-base until it snaps in place.

3) Insert Quick Reference Card into slot on top of thermostat.

NOTE: This thermostat ships configured as a 1H/1C conventional thermostat. Confirm installer settings. See page 9.

Installer Guide 6

3) Insert Quick Reference Card into slot on top of thermostat.

3 Quick Reference

14

13 12

INSTRUCTIONS

1

2

3

16

HUMID

4 5 6

Thermostat Display

Service Indicators ...................... Displays various service/maintenance information

or dehumidification

Time of Day ................................. Displays the current time of day

11

10

9

8

7

15

Wi-Fi/Wireless Indicator .............. Indicates when connected to Wi-Fi/wireless (flashes

when connection has been lost)

Fan Indicator ................................ Indicates when the system fan is running

Thermostat

Quick Reference Instructions ...... Stored in slot located at top of thermostat

SpeedBar

®

................................... Increases or decreases settings (time, temperature, etc.)

Battery Compartment ................. Located in the back of thermostat

7 Installer Guide

INSTRUCTIONS

HUMID

Thermostat TouchPads

NOTE: Thermostat TouchPads are located on the left, right and bottom portions of the display screen. They are

the “touch sensitive” segments used to adjust your thermostat. Depending on the equipment installed, all touch pads may not show.

SYSTEM......

Selects AUTO (Heat/Cool), COOL, OFF HEAT or EMER (Emergency Heat)

FAN.............

Selects AUTO, ON, CIRC (Circulation) and PROG (Program) fan modes

PROG..........

Selects programming mode or press for 3 seconds to select SpeedSet

® mode

HOLD..........

Enters / Exits the HOLD mode (program bypass)

DAY/TIME...

Sets the current time and day of the week

BACK..........

Moves back in setting and programming modes

NEXT...........

Moves forward in setting and programming modes

RETURN......

Returns to normal mode from program or settings modes

CONFIG.......

Enters the User and Installer settings modes

HUMID........

Displays or adjusts the current humidity level

Outdoor Temperature

If an outdoor temperature sensor was connected, you may touch the room temperature area of the screen to view the outdoor temperature.

Installer Guide 8

4 Installer Settings

The Installer Settings must be properly configured in order for this thermostat to operate correctly. The Installer

Settings are menu driven. The portion of these settings that do not apply to your setup will be skipped. These settings are indicated below with comments. More detail on each setting follows this table.

1. Touch and hold down the

SYSTEM and CONFIG TouchPads for 3 seconds.

2. Release both buttons and the first installer setting will be displayed.

3. Change settings as required using the

UP or DOWN portion of the SpeedBar

® .

4. Touch

NEXT or BACK to move to the next or previous setting, touch RETURN to exit.

No. Installer Setting Factory Setting

(

Notes follow this table)

Default

Options

1 Residential or

or Commercial Profile

2 Programming Mode

[note 1]

3 Clock Format

4 Temperature Scale

5 Auto Changeover

6 System Type

7 1st Stage Differential

8 2nd Stage Differential

[note 2]

9 3rd Stage Differential

[note 2]

RES

7 PROG

12 HR

F DEG oF AUTO

11CONV

0.5 DIF1

2.0 DIF2

2.0 DIF3

10 1st Stage Fan Control

[note 3]

HG FAN 1

11 Emergency Heat]

HE EMER

Fan Control [note 4]

12 Reversing Valve

REVO

(O/B Terminal) [note 5]

Comments

(More information follows this table)

RES

COMM

Select for Residential profile

Select for Commercial profile

7 PROG

52 PROG

NO PROG

12 HR

24 HR

F DEG

C DEG

oF AUTO

ON AUTO

11CONV

22CONV

11HP

22HP

32HP

Select for 7 day programming mode

Select for 5-2 day programming mode

Select for non-programmable mode

Select for 12 hour clock

Select for 24 hour clock

Select for Fahrenheit display

Select for Celsius display

Disables Auto Changeover mode

Enables Auto Changeover mode

Select for 1H/1C Conventional system

Select for 2H/2C Conventional system

Select for 1H/1C Heat Pump system

Select for 2H/2C Heat Pump system

Select for 3H/2C Heat Pump system

0.5, 1.0 or

Select a 1st stage temperature differential of .5°,

2.0 DIF1

1° or 2° F (.25°, .5° or 2° C)

1.0, 2.0, 3.0, Select a 2nd stage temperature differential of 1°,

4.0, 5.0 or 2°, 3°, 4°, 5° or 6° F (.5°, 1°, 1.5°, 2°, 2.5° or 3° C)

6.0 DIF2

1.0, 2.0, 3.0, Select a 3rd stage temperature differential of 1°, 2°,

4.0, 5.0 or 3°, 4°, 5° or 6° F (.5°, 1°, 1.5°, 2°, 2.5° or 3°C)

6.0 DIF3

HG FAN 1

HE FAN 1

HE EMER

HG EMER

REVO

REVB

Select for 1st stage Gas heating

Select for 1st stage Electric heating

Select for Electric Emergency Heat

Select for Gas Emergency Heat

Select for cool active Reversing Valve (O terminal)

Select for heat active Reversing Valve (B terminal)

9 Installer Guide

No. Installer Setting Factory Setting

(

Notes follow this table)

Default

Options

Comments

(More information follows this table)

13 Fossil Fuel

15 AC Power Interrupt

Backup Heat

Protection

Warning [note 6]

16 Compressor Short

Cycle Protection

17 Residual Cooling

Fan Delay

AE AUX

[note 4]

14 Compressor Power Outage

oF CPOP

[notes 4, 6]

Select for Electric Auxiliary heat (with compressor)

Select for Gas Auxiliary heat (without compressor)

Disables Power Outage Lockout Delay

Enables Power Outage Lockout Delay

AC oF MONR AC oF MONR Disables AC Power Interrupt Warning

AC on MONR Enables AC Power Interrupt Warning

5 CSCP

5, 4, 3, 2 or Select a compressor short cycle protection delay of 5,

0 CSCP

4, 3, 2 or 0 minutes

60 FAN

AE AUX

AG AUX

oF CPOP

on CPOP

18 Circulating Fan Lock

19 Adaptive Recovery

Mode (ARM™) [note 7]

20 Indoor Remote Sensor

Control* [note 8]

(wireless sensors must be paired)

oF CIRC oF REC

I SENS

90, 60, 30 Select a Residual Cooling Fan Delay of 90, 60, or

0 FAN

30 or 0 seconds.

oF CIRC

on CIRC

oF REC

on REC

I SENS

E SENS

A SENS

Disables Circulating Fan Lock mode

Enables Circulating Fan Lock mode

Disables Adaptive (early) Recovery mode

Enables Adaptive (early) Recovery mode

Temperature is sensed from thermostat only.

Temperature is sensed from remote sensor(s) only.

(averaged if more than one)

Temperature is averaged with the thermostat and

the remote sensor(s).

21 Lockout Security Level

2 LOCK

(set 3-digit code in user settings)

22 Auto Changeover

Dead Band

[note 10]

3 BAND

2 LOCK

1 LOCK

If locked – Complete lockout is enabled

If locked – Partial lockout is enabled (SpeedBar ® still functional)

2, 3, 4 or 5 Select a Dead Band of 2°, 3°, 4° or 5˚ F

BAND

(1°, 2° or 3° C) for Auto Changeover mode.

is

23 Compressor Balance

24 Auxiliary Heat Balance

25 Economizer Fresh Air or

Point

Point

[notes 4, 10]

[notes 4, 10]

Output Control [note 11]

NO BALC

NO BALA

OA NONE

NO BALC

Disables Balance Points

0-50 BALC Select a Compressor Balance Point of 0° - 50°F

(-18° - 10° C)

NO BALA

Disables Balance Points

70-40 BALA Select a Auxiliary Heat Balance Point of 70°- 40° F

(21°- 4° C)

OA NONE

OA ECON

OA TOD

Disables Fresh Air Intake option

Enables Fresh Air Intake (Economizer Mode)

Enables Fresh Air Intake (Time of Day Mode)

26 Heat Set Point Upper Limit

90LIM

27 Cool Set Point Lower Limit

45LIM

28 Humidification

[note 12]

OFF

29 Auto Humidity Set

AUTO

Point Limit

[notes 10, 12]

30 Dehumidification

[note 12]

31 Installer Clear

OFF

CLR0

90-60 LIM Select a Heat Set Point Upper Limit of 90°-60° F (32°-10° C)

45-80 LIM Select a Cool Set Point Lower Limit of 45°-80° F (7°-27° C)

OFF

DEP

IND

AUTO

MAN

OFF

NI

NA

CLR0

CLR1

CLR2

Disables Humidification

Enables Dependant Humidification

Enables Independent Humidification

Enables automatic humidity control based on outdoor temperature.

Enables manual humidity control from thermostat.

Disables Dehumidification

Normally inactive (open) relay

Normally active (closed) relay

Clear Off - No changes made to settings

Clears wireless remote sensor settings

Clears all thermostat settings (factory defaults)

Options (shaded) 28 - 30 only appear if optional wireless remote humidity sensor is installed.

*When an outdoor sensor is connected, the thermostat automatically recognizes it. Press room temperature digits to display outdoor temperature.

NOTE: Additional options such as Service Monitors, Setting the lock code, audible tone, etc. are located in the User Settings – See User manual for information on setting these options.

Installer Guide 10

NOTES - Installer Settings

1 Only available if Residential profile was selected in option 1.

2 Only available if a 2 or 3 stage system type was selected in option 6.

3 Only available if a Conventional system was selected in option 6.

4 Only available if a 2 or 3 stage Heat Pump system was selected in option 6.

5 Only available if a Heat Pump system was selected in option 6.

6 Only available if the 24 Volt AC common wire is connected to the C terminal.

7 Only available if a programmable profile was selected in option 2.

8 Only available if a Braeburn

®

indoor remote sensor is connected (wired or wireless).

9 Only available if auto changeover was enabled in option 5.

10 Only available if a Braeburn outdoor sensor was connected.

11 Only available if Commercial profile was selected in option 1.

12 Only available if a Braeburn wireless humidity sensor (Model 7330) is connected.

Detailed Explanation of Installer Settings (also see NOTES above):

1 Profile – Selects a residential (RES) or commercial (COMM) profile. If residential is selected, 4 programming events per day are available. If commercial is selected, 2 event, 7 day programming is available.

2 Programming Mode [note 1] – Selects the programming mode, either full 7 day or 5-2 day (weekday/ weekend) programming or non-programmable.

3 Clock Type – Selects either a 12 hour or 24 hour clock.

4 Temperature Scale – Selects a temperature scale of either °F or °C.

5 Auto Changeover – Selects auto changeover on or off. When auto changeover mode is enabled and selected, the system automatically switches between heating and cooling modes. There is a 5 minute delay when switching from heating to cooling or cooling to heating in auto changeover mode.

NOTE: Also see “Auto Changeover Dead Band” in option 22.

6 System Type – Selects the system type for your installation. NOTE: Changes made to this option will reset

options 7 through 14 back to their default values dependant on the system type.

7 1st Stage Differential – Selects a 1st stage temperature differential.

8 2nd Stage Differential [note 2] – Selects a 2nd stage temperature differential.

9 3rd Stage Differential [note 2] – Selects a 3rd stage temperature differential.

10 1st Stage Fan Control [note 3] – Selects a 1st stage fan control of either gas or electric heat.

11 Emergency Heat Fan Control [note 4] – Selects emergency heat fan control of either gas or electric heat.

12 Reversing Valve [note 5] – Selects the output state of the O/B terminal. Select O for this terminal to be active in the cool mode or select B for this terminal to be active in the heat mode.

13 Auxiliary Fossil Fuel Heat Pump Control [note 4] – When set to electric (AE AUX), both the compressor

(1st stage) and auxiliary stage(s) will run when a call for auxiliary heat is made. When set to gas (AG AUX), the compressor stage(s) will be locked out one minute after a call for auxiliary heat.

NOTE: This option can be overridden if setting an auxiliary heat balance point in Option 24.

14 Compressor Power Outage Protection [notes 4, 6] – Selects power outage protection on or off. When enabled, this thermostat will provide cold weather compressor protection by locking out the compressor stage(s) of heating for a period of time after a power outage greater than 60 minutes.

11 Installer Guide

15 AC Power Interrupt Warning [note 6] – When enabled, the thermostat will display an outage warning when AC power to the thermostat is lost.

16 Short Cycle Protection – Selects the number of minutes the cooling compressor will be locked out after turning off. This short cycle protection is also active in the heat mode if a heat pump system was selected in

Option 6.

17 Residual Cooling Fan Delay – Selects a delay for the system fan after the cooling compressor has turned off. This delay will help remove the remaining cool air out of the ductwork providing additional efficiency.

18 Circulating Fan Lock – When enabled, the only user fan options available are ON and CIRC (Circulation).

The AUTO option is not available with this option enabled.

19 Adaptive Recovery Mode (early recovery) [note 7] – Enables or disables the ARM

TM

(adaptive recovery mode) feature. During ARM, room temperature is recovered by turning on the heating or cooling before the end of the set back period. The set point temperature is changed to that of the upcoming program temperature.

20 Indoor Remote Sensor Control [note 8] – If a Braeburn

®

indoor remote sensor is connected (wired) or paired (wireless) during installation, the thermostat will automatically detect the sensor. When an indoor sensor is detected, you may select between thermostat only (I SENS), remote sensor only (E SENS) or combining the thermostat and the remote sensor(s) (A SENS).

NOTE: This option does not apply to the Braeburn outdoor sensor. When an outdoor sensor is connected

(wired) or paired (wireless), the thermostat automatically recognizes it and no further configuration is necessary.

21 Lockout Security Level – Selects the level of keypad lockout when the thermostat is locked. Level 2 locks the entire thermostat (including the front reset button). Level 1 locks everything except the SpeedBar

® allowing for up and down temperature adjustment. NOTE: The lock code is set in the User Settings mode

(see User Manual).

22 Auto Changeover Dead Band [note 9] – When auto changeover mode is enabled in option 5 and selected, the system automatically switches between heating and cooling when the room temperature meets the normal criteria for either a heating or cooling call. There is a forced separation (dead band) between the heating and cooling set points so that the systems do not work against each other. This option selects the amount of this dead band in degrees with the default being 3° F.

23 Compressor Balance Point [notes 4, 10] – Locks out the use of the compressor heat stage when the outside air temperature is less than the selected setting of 0 ˚F to 50 °F (-9° C to 10° C)

24 Auxiliary Heat Balance Point [notes 4, 10] – Locks out the use of the auxiliary heat stage when the outside air temperature exceeds the selected setting of 70° F to 40° F (21° C to 4° C). NOTE: This balance

point overrides the fossil fuel compressor lockout in option 13. If this option is set to gas and the outdoor temperature is over the auxiliary balance point, the compressor will remain on during a call for auxiliary heat.

Installer Guide 12

25 Economizer, Fresh Air or Output Control [note 11] – Selects control options. Select between disabled

(NONE), economizer mode (ECON) and time of day (TOD) mode.

Time Step / Override Cooling Call

Occupied

Unoccupied

Override

YES or NO

YES

NO

YES or NO

External Air or Output Control (A)

Economizer Time of Disabled

Mode Day Mode

ON

ON

OFF

ON

ON

OFF

OFF

ON

OFF

OFF

OFF

OFF

Time Step / Override Heating Call

Occupied

Unoccupied

Override

YES or NO

YES

NO

YES or NO

External Air Output (A)

Economizer Time of Disabled

Mode Day Mode

ON

OFF

OFF

ON

ON

OFF

OFF

ON

OFF

OFF

OFF

OFF

26 Heat Set Point Upper Limit – Selects the heating set point upper adjustment limit.

27 Cool Set Point Lower Limit – Selects the cooling set point lower adjustment limit.

28 Humidification Mode [note 12] – For use with an external humidifier. Selects between disabling humidification (OFF), dependent control (DEP) or independent control (IND). The DEP setting controls humidification only during a call for heating. The IND setting allows humidification output in the heat mode, but does not require a call for heating. NOTE: It is recommended that the IND setting only be used with

systems designed for low air temperature humidification such as steam humidification. Always ensure the heat exchanger or other system parts are not exposed to excess water from condensation or other sources.

When there is any doubt, use the OFF or DEP setting.

29 Auto Humidity Set Point Limit [notes 10, 12] – Select between turning the automatic humidity set point limit to auto (AUTO) or manual (MAN). When AUTO is selected, humidity control is provided automatically based on the outdoor temperature. Selecting MAN allows you to manually control the level of humidity.

30 Dehumidification [note 12] – For use with an external dehumidifier. Select between dehumidification disabled (OFF), a normally inactive (NI) or normally active (NA) relay, depending on the requirements of your external dehumidification equipment.

31 Installer Clear – Clears settings based on your selection. CLRO makes no changes, CLR1 clears all wireless remote sensor settings and CLR2 clears ALL thermostat settings to factory default.

WARNING: If you press NEXT or RETURN after selecting CLR1 or CLR2 the clear will take place and the appropriate settings will be returned to factory defaults. If you do not wish to make any changes, use the

SpeedBar

®

to select CLRO.

13 Installer Guide

5 Wireless Remote Sensors

NOTE: See the wireless remote sensor manual for complete installation and use instructions.

Compatible Wireless Remote Sensors

Wireless Remote Indoor Sensor(s) – 4 sensors maximum

Wireless Remote Outdoor Sensor – 1 sensor maximum

Wireless Remote Humidity Sensor – 1 sensor maximum

NOTE: No more than 4 wireless remote sensors can be connected.

Pairing Wireless Remote Sensors

1 Press and hold the CONFIG and DAY/TIME buttons for 3 seconds.

2 Press NEXT until the word SENS appears in the display and the symbol flashes.

3 After the remote sensor is powered, press and hold the CONNECT button at the sensor for 3 seconds.

4 The remote sensor will enter pairing mode for 60 seconds. During this time the blue LED on the wireless

remote sensor will flash once every 2 seconds.

5 The thermostat display will change and indicate which remote sensor has been paired (see Table 1). The

symbol will stop flashing and the blue LED on the remote sensor will turn on for 60 seconds.

6 To pair another wireless remote sensor, press NEXT and repeat steps 3 - 5.

7 Press RETURN at any time to exit.

NOTE: Sensors that have already been paired will appear in the thermostat display first, with a solid symbol.

IDS1, IDS2, IDS3 or IDS4

Remote Indoor Sensor 1-4

HMS

ODS

Remote Humidity Sensor

Remote Outdoor Sensor

Table 1

Using Wired Remote Sensors

One wired indoor or wired outdoor remote sensor can also be connected to the thermostats S1 and S2 terminals using 2-wire thermostat cable.

You cannot mix wired and wireless remote sensors of the same type (i.e. mixing an indoor wireless remote sensor and an indoor wired remote sensor).

Replacing a Thermostat

If you are replacing a thermostat that is paired with an existing wireless sensor, you will need to clear the remote sensor and pair it again with the newly installed thermostat.

1 Install the new thermostat.

2 On the wireless remote sensor you want to clear, press and hold the CONNECT button for 10 seconds until the

red LED turns on solid.

3 Release the CONNECT button and the blue and red LED will each flash once to indicate the sensor was

successfully cleared.

4 Pair the remote sensor again.

Replacing a Sensor

If you are replacing a wireless remote sensor that is paired with an existing thermostat, you will need to clear the thermostat’s remote sensor settings before pairing the new wireless remote sensor.

1 Install the new wireless remote sensor.

2 Thermostat remote sensor settings are cleared by adjusting Installer Setting 31 to CLR1 (see pages 9-10).

This setting clears all the remote sensors paired with the thermostat.

NOTE: Be careful not to select CLR2 unless you want to clear all the thermostat settings.

3 Once the remote sensor settings are cleared you will need to pair your new wireless remote sensor. You will

also need to pair any other existing wireless remote sensors that were previously connected.

Installer Guide 14

Wireless Remote Sensor Communication Loss

If communication between the remote sensor and thermostat is lost, the red LED on the remote sensor will begin to flash once every 10 seconds. The sensor will attempt to reconnect to the thermostat several times automatically.

NOTE: To attempt to reconnect manually, press and hold the CONNECT button for 3 seconds.

The thermostat display will also indicate which wireless remote sensor has lost communication by flashing

COMM LOSS along with the remote sensor that has lost communication (see Table 2).

Wireless Remote Sensor Low Battery

If the batteries in a wireless remote sensor are low, the red LED will flash 3 times every 30 seconds. The thermostat display will also indicate which wireless remote sensor has a low battery by flashing LOW BATT along with the remote sensor that has the low battery condition (see Table 2). Replace the remote sensor batteries immediately.

IDS1, IDS2, IDS3 or IDS4 Remote Indoor Sensor 1-4

HMS

Remote Humidity Sensor

ODS Remote Outdoor Sensor

Table 2

NOTE: If Audible Tone is enabled in User Options (see User Manual), the thermostat will also sound a beep every

60 seconds when communication has been lost. You can press RETURN to cancel the beeping sound.

6 System Testing

Warning

Read Before Testing

• Do not short (or jumper) across terminals on the gas valve or at the heating or cooling system control board to test the thermostat installation. This could damage the thermostat and void the warranty.

• Do not select the COOL mode of operation if the outside temperature is below 50º F (10º C). This could possibly damage the controlled cooling system and may cause personal injury.

• This thermostat includes an automatic compressor protection feature to avoid potential damage to the compressor from short cycling. When testing the system, make sure to take this delay into account.

NOTE: The compressor delay can be bypassed by pressing the reset button on the front of the thermostat.

All user settings will be returned to factory default, however all Installer settings will remain as originally programmed in section 4.

1 Touch the SYSTEM TouchPad until the thermostat is in HEAT mode.

2 Using the SpeedBar

®

raise the set temperature a minimum of 3 degrees above the current room

temperature. The system should start within a few seconds. With a gas heating system, the fan may

not start right away.

3 Touch SYSTEM until the thermostat is in the OFF mode. Allow the heating system to fully shut down.

4 Touch SYSTEM until the thermostat is in the COOL mode.

5 Using the SpeedBar lower the set temperature a minimum of 3 degrees below the current room

temperature. The system should start within a few seconds (unless compressor short cycle protection

is active – See note above).

6 Touch SYSTEM until the thermostat is in the OFF mode. Allow the cooling system to fully shut down.

7 Touch FAN until the thermostat is in FAN ON mode. The system fan should start within a few seconds.

8 Touch FAN until the thermostat is in FAN AUTO mode. Allow the system fan to turn off.

9 If the thermostat is controlling auxiliary equipment such as an economizer etc., adjust the thermostat

settings to test these devices.

15 Installer Guide

®

FCC Compliance Statement (Part 15.19) (USA only)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1 This device may not cause harmful interference, and

2 This device must accept any interference received, including interference that may cause undesired operation.

FCC Warning (Part 15.21) (USA only)

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC Interference Statement (Part 15.105 (b)) (USA only)

this equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Equipment interface module, thermostats and outdoor sensor

To comply with FCC and Industry Canada RF exposure limits for general population/ uncontrolled exposure, the antenna(s) used for these transmitters must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna.

Portable Comfort Control

This portable transmitter with its antenna complies with FCC and industry Canada RF exposure limits for general population/uncontrolled exposure.

This device must not be co-located or operating in conjunction with any other antenna or transmitter.

Section 7.1.2 of RSS-GEN

Under industry Canada regulations, this radio transmitter may only operate using an antenna of type and maximum (or lesser) gain approved for the transmitter by industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

Section 7.1.3 of RSS-GEN

Operation is subject to the following two conditions:

1 This device may not cause interference, and

2 This device must accept any interference, including interference that may cause undesired operation of the device.

MPEG LA License Agreement

THIS PRODUCT IS LICENSED UNDER THE WIRELESS NETWORK PATENT PORTFOLIO LICENSE FOR USE BY A CONSUMER OR OTHER USES FOR WHICH

THERE IS NO REMUNERATION. ANY OTHER USE OF THIS PRODUCT IN ANY MANNER IS NOT LICENSED AND IS EXPRESSLY PROHIBITED WITHOUT A

LICENSE UNDER APPLICABLE PATENTS IN THE WIRELESS NETWORK PATENT PORTFOLIO, WHICH LICENSE IS AVAILABLE FROM MPEG LA, LLC, 4600 S.

ULSTER ST., SUITE 400, DENVER, COLORADO 80237 U.S.A. SEE HTTP://WWW.MPEGLA.COM.

Limited Warranty

When installed by a professional contractor, this product is backed by a 5 year limited warranty. Limitations apply. For limitations, terms and conditions, you may obtain a full copy of this warranty:

· Visit us online: www.braeburnonline.com/warranty

· Phone us: 866.268.5599

· Write us: Braeburn Systems LLC

2215 Cornell Avenue

Montgomery, IL 60538

5

YEAR

LIMITED

WARRANTY

Store this manual for future reference.

www.bluelinksmartconnect.com

®

Braeburn Systems LLC

2215 Cornell Avenue • Montgomery, IL 60538

Technical Assistance: www.braeburnonline.com

844-BLU-LINK (844-258-5465) (U.S.)

630-844-1968 (Outside the U.S.)

©2015 Braeburn Systems LLC • All Rights Reserved • Made in China.

7320-100-01

advertisement

Related manuals

Download PDF

advertisement