Exterior Dot-HP - Martin Professional

Exterior Dot-HP - Martin Professional
Exterior Dot-HP™
User Manual
Please check that you have the latest user manual for this product before
installing, operating or servicing the product.
User manual revisions are identified at the bottom of page 2. You can download the
latest user documentation from the Product Support / Tech Docs pages at
www.martin.com
Dimensions
Exterior Dot-HP, clear front
34
55
177
Ø72
177
55
Ø18
Ø16
Input
Throughput
Exterior Dot-HP, diffuser dome front
49
33
55
177
Ø72
177
55
Ø18
Ø16
Input
Throughput
Direct dot-to-dot connection allows up to 0.5 m (19.6 in.) pixel pitch
All dimensions are in millimeters
© 2015-2016 Martin Professional ApS. Information subject to change without notice. Martin Professional and all affiliated companies
disclaim liability for any injury, damage, direct or indirect loss, consequential or economic loss or any other loss occasioned by the
use of, inability to use or reliance on the information contained in this document. The Martin logo, Martin name, Harman name and all
other trademarks in this document pertaining to services or products by Martin Professional or its affiliates and subsidiaries are trademarks owned or licensed by Martin Professional or its affiliates or subsidiaries.
Exterior Dot-HP™ User Manual P/N 5080227 Rev. A (preliminary)
Exterior Dot-HP mounting plate
Ø4.5
Ø6.5
Ø15
54 45
26
86
100
3
Exterior Dot-HP mounting profile
38
51
43
28.5
36
27
57
Mounting profile shown with dot bracket installed
26
45
Ø6.5
20
All dimensions are in millimeters
Dimensions
3
Contents
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Precautions to avoid damage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Exterior Dot-HP™ overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Physical installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Avoiding damage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Mounting on a surface or structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Installing using mounting profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
System installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Installing a P3 system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Installing a DMX-controlled system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
System setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Setting up for P3 display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Setting up for DMX control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
RDM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Using the Exterior Dot-HP™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Thermal regulation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
P3 display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DMX control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Magnetic ‘control button’ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
26
26
26
27
Service and maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Condensation and pressure relief valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LED performance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing new software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
30
30
30
31
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
DMX protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
RGB Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Basic Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Pre-programmed FX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
4
Exterior Dot-HP™ User Manual
Safety information
WARNING!
Read the safety precautions in this section before
installing, powering, operating or servicing this
product.
The following symbols are used to identify important safety information on the product and in this document:
Warning!
Warning!
Safety hazard.
Hazardous
Risk of severe voltage. Risk
injury or
of severe or
death.
lethal electric
shock.
Warning!
Fire hazard.
Warning!
Burn hazard.
Hot surface
with risk of
burns.
Warning!
Refer to user
manual.
Warning!
• Check the Exterior Dot-HP™ Product Support / Tech Docs page on the Martin™ website at
www.martin.com and make the sure that you have the latest user documentation for the product.
Martin™ user manual revisions are identified at the bottom of page 2.
• Read the latest revision of the user manual before installing, operating or servicing the Martin
Exterior Dot-HP™.
• Follow the safety precautions given in this user manual and in the manuals of all the devices you
connect to the product. Observe all warnings given in manuals and printed on devices. Make sure
that everyone who is involved in working on or using the product has read and understood these
safety precautions and warnings.
• Install, connect, operate and service devices only as described in this user manual and in
connected devices’ user documentation and only in accordance with local laws and regulations.
All Martin™ user documentation is supplied with devices and available for download from
www.martin.com.
• This product is suitable for installations where chains of Exterior Dot-HP™ dots are located
outdoors, provided that either:
- Each chain is connected to a device that is earthed (grounded) such as a Martin™ P3 PowerPort
or a Martin™ IP66 PSU 240W device and maximum 10 m (32 ft.) total in length, or
- Each chain is secured directly to an earthed (grounded) metal structure.
The above conditions are based on the provisions of Installation Class 3, EN 61000-4-5, under
which surges may not exceed 2 kV.
• This product is not for household use. It presents risks of severe injury or death due to fire and
burn hazards, electric shock and falls. It must be installed by qualified technicians only.
• This product does not have user-serviceable parts. Refer any operation not described in this
manual to Martin™ Global Service or a Martin™ authorized service agent.
If you have any questions about how to operate this product safely, please contact your Martin™ supplier or
call the Martin™ 24-hour service hotline on +45 8740 0000, or in the USA on 1-888-tech-180.
Safety information
5
PROTECTION FROM ELECTRIC SHOCK
• Read and respect the directions given in the user documentation of all the devices that you intend to
connect to the Exterior Dot-HP™, particularly the instructions, warnings and limits that apply to:
- system layout,
- connections to other devices,
- specified cables,
- maximum cable lengths, and
- maximum number of devices that can be connected.
• Use only the cables specified in this manual and on the Martin™ website at www.martin.com to
interconnect devices in the installation. If the specified cables are not long enough for an intended cable
run, consult Martin™ for assistance in finding or creating a safe alternative solution.
• Provide a means of locking out AC mains power so that power to the installation can be shut down and
made impossible to reapply, even accidentally, during work on the installation.
• Shut down power to the installation during service and when it is not in use.
• Before applying power to the installation, check that all power distribution equipment and cables are in
perfect condition and rated for the current requirements of all connected devices.
• Isolate the installation from power immediately if any product, power cable or power plug is in any way
damaged, defective, or if it shows signs of overheating.
• Do not immerse the Exterior Dot-HP™ in water.
• If you supply a chain of Exterior Dot-HP™ dots with DC power from a generic 48 VDC external PSU and
the DC output used does not have constant overcurrent protection that limits current to 7.5 A, install an
inline fuseholder with a 7.5 A fuse on the circuit that you connect to that DC output.
• Do not allow the total number of dots in a linked chain of Exterior Dot-HP™ dots to exceed the safe limits
given in the tables in the following section of this manual.
Safety limits for connecting devices
This user manual (Revision A) contains preliminary information on safety limits for connecting devices. We
are currently (from November 2016) preparing more complete information on the maximum number of
Exterior Dot-HP™ dots that can be interconnected in a chain and the maximum permitted length of a chain,
and we will publish this information in a later revision of the manual. In the meantime, please respect the
limits given here.
Do not exceed the maximum safety limits given below and in the following tables.:
• The maximum permitted total length of a chain of Exterior Dot-HP™ dots is 120 m (394 ft.). When you
calculate the total length of the chain, include the cable tails on dots (1 meter or 3.3 feet per dot) plus the
lead-in cable (cable between the DC power source and the first Exterior Dot-HP™ dot), plus all extension
cable added between dots.
• The maximum permitted length of a lead-in cable is 100 m (328 ft.).
• The maximum permitted length of cable between two Exterior Dot-HP™ dots is 20 m (65 ft.). If you need
a distance longer than 20 m between two dots, create a new chain of dots with its own power and data
source.
• The maximum number of Exterior Dot-HP™ dots that you can connect in one chain depends on the
following:
- type of device used as DC power source
- length of chain from DC power source to last Exterior Dot-HP™ dot in chain
- calibration mode of Exterior Dot-HP™ dots: uncalibrated or calibrated mode.
Do not exceed the limits given in the following sections.
Martin P3 PowerPort 1500™ safety limits
If you supply Exterior Dot-HP™ dots with DC power from a Martin P3 PowerPort 1500™:
• Do not connect more than one chain of dots per DC output on the P3 PowerPort 1500™. Since the P3
PowerPort 1500™ has four DC outputs, you can connect a maximum of four chains of dots to one P3
PowerPort 1500™.
• Check whether there is a possibility that the dots may be used in uncalibrated mode or whether the dots
will be used in calibrated mode only:
- If there is a possibility that the dots may be used in uncalibrated mode, consult the figures for
‘Uncalibrated mode or mixed calibrated and uncalibrated modes’ in Table 1.
- If the dots will be used in calibrated mode only, consult the figures for ‘Calibrated mode only’ in Table 1.
6
Exterior Dot-HP™ User Manual
• Do not exceed the maximum total number of dots that you can include in one chain for the total cable
lengths listed in Table 1. If the total cable length is not given in the table, respect the maximum total
number of dots given for the next highest length. In other words, if you create a cable with a total length of
46 m, do not exceed the maximum total number of dots for a chain with a 70 m cable length.
Maximum permitted
number of dots in
chain
Uncalibrated mode or
mixed calibrated and
uncalibrated modes
(7 W per dot)
Calibrated mode only
(5 W per dot)
45 m (147 ft.) total cable length
44
70 m (230 ft.) total cable length
41
115 m (377 ft.) total cable length
33
45 m (147 ft.) total cable length
63
70 m (230 ft.) total cable length
58
115 m (377 ft.) total cable length
48
Table 1: Max. number of Exterior Dot-HP™ dots per P3 PowerPort 1500™ output
Martin P3 PowerPort 1000 IP™ safety limits
If you supply Exterior Dot-HP™ dots with DC power from an output on a Martin P3 PowerPort 1000 IP™:
• Do not connect more than one linked chain of Exterior Dot-HP™ dots to one DC output. Since the P3
PowerPort 1000 IP™ has four DC outputs, you can connect a maximum of four chains of dots to one P3
PowerPort 1000 IP™.
• Check whether there is a possibility that the dots may be used in uncalibrated mode or whether the dots
will be used in calibrated mode only:
- If there is a possibility that the dots may be used in uncalibrated mode, consult the figures for
‘Uncalibrated mode or mixed calibrated and uncalibrated modes’ in Table 2.
- If the dots will be used in calibrated mode only, consult the figures for ‘Calibrated mode only’ in Table 2.
• Do not exceed the maximum total number of dots that you can include in one chain for the total cable
lengths listed in Table 2. If the total cable length is not given in the table, respect the maximum total
number of dots given for the next highest length. In other words, if you create a cable with a total length of
46 m, do not exceed the maximum total number of dots for a chain with a 70 m cable length.
Maximum permitted
number of dots in
chain
Uncalibrated mode or
mixed calibrated and
uncalibrated modes
(7 W per dot)
Calibrated mode only
(5 W per dot)
45 m (147 ft.) total cable length
30
70 m (230 ft.) total cable length
29
115 m (377 ft.) total cable length
25
45 m (147 ft.) total cable length
45
70 m (230 ft.) total cable length
42
115 m (377 ft.) total cable length
37
Table 2: Max. number of Exterior Dot-HP™ dots per P3 PowerPort 1000 IP™ output
Safety information
7
Martin™ IP66 PSU 240W safety limits
If you supply Exterior Dot-HP™ dots with DC power from a Martin™ IP66 PSU 240W external power supply
unit:
• Do not connect more than one linked chain of Exterior Dot-HP™ dots to the DC power output of the
Martin™ IP66 PSU 240W.
• Check whether there is a possibility that the dots may be used in uncalibrated mode or whether the dots
will be used in calibrated mode only:
- If there is a possibility that the dots may be used in uncalibrated mode, consult the figures for
‘Uncalibrated mode or mixed calibrated and uncalibrated modes’ in Table 3.
- If the dots will be used in calibrated mode only, consult the figures for ‘Calibrated mode only’ in Table 3.
• Do not exceed the maximum total number of dots that you can include in one chain for the total cable
lengths listed in Table 3. If the total cable length is not given in the table, respect the maximum total
number of dots given for the next highest length. In other words, if you create a cable with a total length of
46 m, do not exceed the maximum total number of dots for a chain with a 70 m cable length.
Maximum permitted
number of dots in
chain
Uncalibrated mode or
mixed calibrated and
uncalibrated modes
(7 W per dot)
Calibrated mode only
(5 W per dot)
45 m (147 ft.) total cable length
29
70 m (230 ft.) total cable length
28
115 m (377 ft.) total cable length
24
45 m (147 ft.) total cable length
42
70 m (230 ft.) total cable length
40
115 m (377 ft.) total cable length
36
Table 3: Max. number of Exterior Dot-HP™ dots per Martin™ IP66 PSU 240W
Generic 48 VDC external PSU safety limits
If you supply a chain of Exterior Dot-HP™ dots with DC power from a 48 VDC external PSU (power supply
unit) that is not from Martin™, you must not exceed the maximum power rating of the output from the
PSU. Follow these instructions:
• Check whether there is a possibility that the dots may be used in uncalibrated mode or whether the dots
will be used in calibrated mode only:
- If there is a possibility that the dots may be used in uncalibrated mode, allow a power consumption of 7
watts per dot.
- If the dots will be used in calibrated mode only, allow a power consumption of 5 watts per dot.
• Calculate the total power consumption in watts of the dots in each chain you plan to create. Do not create
a chain that will exceed the maximum power rating of the PSU output used to supply that chain with
power. Each time the total power consumption in watts for one chain reaches the PSU output’s maximum
power rating, you must create a new chain of dots that is connected to a new 48 VDC power output.
• Do not exceed the maximum total number of dots that you can include in one chain for the total cable
lengths listed in Table 4. If the total cable length is not given in the table, respect the maximum total
number of dots given for the next highest length. In other words, if you create a cable with a total length of
46 m, do not exceed the maximum total number of dots for a chain with a 70 m cable length.
8
Exterior Dot-HP™ User Manual
Maximum permitted
number of dots in
chain
Uncalibrated mode or
mixed calibrated and
uncalibrated modes
(7 W per dot)
Calibrated mode only
(5 W per dot)
45 m (147 ft.) total cable length
29
70 m (230 ft.) total cable length
28
115 m (377 ft.) total cable length
24
45 m (147 ft.) total cable length
42
70 m (230 ft.) total cable length
40
115 m (377 ft.) total cable length
36
Table 4: Max. number of Exterior Dot-HP™ dots per generic 240 watt external PSDU
PROTECTION FROM BURNS AND FIRE
• The Exterior Dot-HP™ is cooled by convection. Provide free airflow and a minimum clearance of 10 mm
(0.4 in.) around the product.
• Do not operate the Exterior Dot-HP™ if the ambient temperature (Ta) exceeds 55° C (131° F).
• The surface of the product can become hot when in use. Take precautions to avoid accidental skin
contact.
• Do not modify the Exterior Dot-HP™ in any way not described in this manual or install other than genuine
Martin™ parts. Use only accessories approved by Martin™.
PROTECTION FROM INJURY
• Read carefully the chapter “Physical installation” on page 13 and respect the limits and instructions given
in that chapter.
• Ensure that the installation hardware and supporting surface or structure can hold at least 10 times the
weight of all the devices they support.
• Block access below the work area and work from a stable platform whenever installing, servicing or
moving the Exterior Dot-HP™.
• Make sure that all items are securely installed, taking into consideration all possible environmental
conditions including temperature variation and wind. Make sure that it is impossible for items to fall and
cause injury or damage.
• Use grade 8.8 strength fasteners that are suitable for their purpose and for the installation environment.
• Fasten Exterior Dot-HP™ products to the supporting surface or structure with a minimum of two fasteners
(screws, bolts, etc.) per product.
• Either use self-locking nuts or use lockwashers with standard nuts on all machine screws and bolts.
Safety information
9
Introduction
Thank you for selecting a product from the Martin Exterior Dot-HP™ family. These compact LED-based
display fixtures are designed to integrate into a Martin P3™ video system, where they can display video
from a variety of sources. Each fixture forms one pixel in the video display. As well as video, the Exterior
Dot-HP™ can be controlled using a DMX lighting controller. Use of an RDM-compliant DMX controller such
as the Martin M-PC™ also allows two-way communication and remote management of Exterior Dot-HP™
fixtures from the controller.
The Exterior Dot-HP™ has an array of LEDs in a circular cast aluminum housing with a front cover that is
permanently sealed onto the unit to give a rugged IP66-rated dot. Dots are supplied in clear front, diffuser
dome and directional front versions. All versions are available as either RGB or CW (cool white) models,
and various mounting options are available from Martin™ (see “Accessories” on page 36).
A hybrid (combined power and data) cabling system allows Exterior Dot-HP™ dots to be daisy-chained for
easy setup and minimal cabling.
The Exterior Dot-HP™ system offers the following features:
• IP66-rated dots and connectors
• Fast, flexible mounting options
• Range of optical variants
• Individually controllable red, green and blue pixel groups in RGB dots
• High-quality 16-bit per color RGB image processing technology in RGB dots
• Pixel-level brightness and color calibration for optimal image quality
• P3 video and DMX lighting control with automatic protocol detection
• Intuitive pixel mapping and addressing using a controller from the Martin P3™ system controller range
• Single hybrid cable carrying both power and data
• External power and data processor from the Martin P3 PowerPort™ range and simple cabling system
• Corrosion resistance to C5-M (very high corrosivity environments including marine / coastal / offshore
according to ISO 12944).
• Clear anodized finish as standard, with custom RAL colors available by special order
For detailed dimensions drawings in various file formats of all the products in the Exterior Dot-HP™ family,
please see the Exterior Dot-HP™ Tech Docs / Product Support pages on the Martin™ website at
www.martin.com
Martin™ user documentation is supplied with products and available for download from www.martin.com,
where you can also find the latest specifications, firmware updates and support information for all Martin™
products. Before you install or use the Exterior Dot-HP™, please check www.martin.com and make sure
that you have the latest user documentation for this product. Martin™ user documentation revisions are
identified at the bottom of page 2.
At Martin™ we welcome input from users. Comments or suggestions regarding this manual can be e-mailed
to [email protected] or posted to: User Documentation, Martin Professional ApS, Olof Palmes Allé 18,
DK-8200 Aarhus N, Denmark.
10
Exterior Dot-HP™ User Manual
Precautions to avoid damage
Important! To get the best out of the Exterior Dot-HP™ and avoid causing damage that is not covered by
the product warranty, make sure that everyone who is involved in installing, working on or using the Exterior
Dot-HP™ has read and understood the following information.
Cleaning
Excessive dirt buildup causes overheating and may lead to damage that is not covered by the product
warranty. Clean the product at regular intervals (see “Cleaning” on page 30).
Operating temperature precautions
• Do not operate the Exterior Dot-HP™ in an ambient temperature that exceeds the specified maximum of
55° C (131° F) for showing average video content.
• Exterior Dot-HP™ dots have an internal thermal sensor. If the sensor measures excessive temperature, a
thermal protection cutout shuts down the dot. The dot will not function normally again until the
temperature has fallen to a safe level.
• When using a Martin P3™ System Controller you can enable "thermal throttling" functionality. This feature
gradually dims dots if they get hot, avoiding full thermal shutdowns.
Sealing unused connectors with blanking caps
Blanking caps for female BBD connectors can be ordered separately in sets of 10 (see “Connectors” on
page 37). Install blanking caps on all unused female BBD connectors to seal them against water and dirt,
otherwise short-circuits and damage may occur.
Maintaining IP66 protection
The Exterior Dot-HP™ is supplied as a sealed unit. Do not try to remove optical components or disassemble
the product in any other way or you will affect the product’s IP66-rated weatherproofing, which may cause
the product to malfunction and lead to damage.
Pressure relief vent
A vent with a Gore-Tex membrane in the base of the product equalizes pressure by allowing air to pass
through it when the product heats up and cools down, but at the same time it acts as a barrier to water in
liquid form. The expulsion of warm air (with a slightly higher water vapor content) and intake of cool air (with
a slightly lower water vapor content) prevents humidity buildup over time, provided that the vent works
correctly and that the product is correctly sealed.
Vents become blocked over time as the micropores in the membrane fill with particles. If a vent becomes
blocked by dirt – or by water if it has formed a pool over the vent – excess pressure can damage seals or
cause air and even water to be sucked into the product along cables. Vents cannot be cleaned and must be
replaced if not in perfect condition. Vent replacement intervals depend on the amount of airborne dirt and
dust in the installation location. Please contact an authorized Martin service agent for vent replacement.
• Any water that reaches the base of an Exterior Dot-HP™ will normally drain away, so there is normally no
risk of water forming a pool on a vent. However, do not install a dot in any way that prevents rainwater,
condensation etc. from draining away from the base of the dot.
• Contact an authorized Martin™ service agent for vent replacement if the vent shows signs of
contamination or is not in perfect condition.
• Vents must be replaced by an authorized Martin service agent after an extended period of use. Intervals
for vent replacement depend on the installation environment.
Introduction
11
Exterior Dot-HP™ overview
B
C
D
A
E
A - DC power + data male BBD-type input
connector
B - DC power + data female BBD-type output
(thru) connector
C - Dot fixture
D - Pressure relief vent
E - Mounting plate (optional accessory)
Figure 1: Overview
12
Exterior Dot-HP™ User Manual
Physical installation
Warning! Read “Safety information” on page 5 before installing the Exterior Dot-HP™ and read all of
this ‘Physical installation’ chapter before starting work.
You can install the Exterior Dot-HP™ on a surface or structure using one of two methods:
• You can fasten Exterior Dot-HP™ dots to mounting plates and then fasten the mounting plates to the
surface or structure.
• You can fasten Exterior Dot-HP™ mounting profile to a flat surface or structure first and then clip and lock
Exterior Dot-HP™ dots onto the mounting profile. This option lets you conceal up to two cable runs inside
the profile, giving a clean appearance.
The Exterior Dot-HP™ can be installed in any orientation.
Do not install Exterior Dot-HP™ dots with a cable run longer than 20 m (65 ft.) between any two dots.
Allow free airflow around the product and at least 10 mm (0.4 in.) of clearance around the front surface.
The Exterior Dot-HP™ is designed to withstand water projections such as rainfall and low-pressure water
jets and can be installed outdoors, but do not submerge it and do not install it in a location where water can
build up around the dot or under the base of the dot. If necessary, provide drainage at the installation
location.
Avoiding damage
Avoid causing damage that is not covered by the product warranty by following these instructions carefully.
Keeping connections dry
Moisture on connectors can cause short circuits and damage to products. Check that all connectors are
perfectly dry before you connect them. Do not install the Exterior Dot-HP™ during wet weather conditions or
if condensation is visible on any surfaces.
Avoiding shocks and stress
Do not expose the Exterior Dot-HP™ to physical shocks (by dropping onto a hard surface, for example).
Do not apply pressure to or otherwise stress diffusers or lenses.
Do not stress cables (by bending them sharply, for example). Protect cables from sharp edges.
Protecting from galvanic corrosion
Dots and profiles are manufactured in marine-grade corrosion-resistant anodized aluminum, but take
precautions to avoid direct contact between aluminum and other metals, as this can cause galvanic
corrosion:
• Use an electrically insulating material (such as rubber or plastic) or a coating between aluminum dots or
mounting profiles and any other metal.
• Use a non-conductive coating such as Delta Seal on fasteners (screws, bolts, washers, etc.) where they
come into contact with dots or mounting profiles.
Physical installation
13
Pressure relief vent
The air inside dots expands and
contracts as components warm
up and cool down. See Figure 2.
To equalize the resulting pressure
variations without allowing water
into the dot, the Exterior
Dot-HP™ features a pressure
relief vent (arrowed) with a
Gore-Tex membrane.
Do not allow pressure relief vents
to become submerged in water or
blocked.
Figure 2: Pressure relief vent
If a vent is not in perfect condition, do not operate the dot. Contact Martin™ Service for replacement.
Mounting on a surface or structure
Installing using mounting plates
The mounting plates available from Martin™ as optional accessories for the Exterior Dot-HP™ (see
“Accessories” on page 36) are recommended for installation on a flat surface or structure.
All fasteners must be suitable for the application and environment. Steel fasteners must be grade 8.8
minimum. Stainless steel fasteners must be grade 304 (A2) or better,. In marine environments, stainless
steel fasteners must be grade 316 (A4) or better.
To install an Exterior Dot-HP™ using a mounting plate:
1. To reduce galvanic corrosion, apply a non-conductive coating such as Delta Seal to all parts of the bolts
that will come into contact with the dot.
B
A
Figure 3: Installing using a mounting plate
2. See illustration above. Fasten the mounting plate to the base of the dot using the four M4 x 8 mm
countersunk Torx screws A supplied with the mounting plate.
3. For each dot, obtain two grade 8.8 or better M6 (quarter-inch) fasteners (screws, screwbolts, etc.) and
screw plugs. You can use M6 machine screws and self-locking nuts if you have access to the back of the
installation surface. Check that fasteners are suitable for the application and have appropriate corrosion
resistance.
4. With reference to “Dimensions” on page 2 and page 3, prepare two holes with centers 86 mm (3.39 in.)
apart in the installation surface to accept two fasteners passed through the holes in the mounting plate.
Use screw plugs if necessary to ensure a secure installation.
5. Fasten the Exterior Dot-HP™ and mounting plate assembly securely to the surface using two fasteners
B per mounting plate.
14
Exterior Dot-HP™ User Manual
6. Connect the dot’s input connector to the output connector of the previous device on the link, either
directly or via a patch cable. Make sure that all connectors are correctly fastened together with locking
rings twisted to ensure a seal.
7. Check that the dot is held securely before you leave it.
Installing directly on a surface
It is also possible to install the Exterior Dot-HP™ directly on a surface such as a metal plate if you have
access to the back of the surface.
To install an Exterior Dot-HP™ on a surface:
1. Pre-drill the surface with four holes suitably positioned to accept mounting screws.
2. Obtain four M8 machine screws or bolts of a suitable length to pass through the surface and into the dot.
3. Apply a small amount of Loctite to the threads of the screws or bolts, then pass them through the surface
and fasten them into the back of the dot.
Installing using mounting profile
To simplify installation on a surface or structure, you can install Exterior Dot-HP™ mounting profiles on the
surface and then fasten Exterior Dot-HP™ dots into the profiles. Martin™ supplies mounting profiles as
optional accessories in kits (see “Mounting hardware” on page 36). The mounting profile is deep enough to
hold two cable runs behind a dot.
See Figure 4. Each mounting profile kit includes:
• Mounting profile D
• Lock assembly E and locking bolt F
• Bracket B
• Four screws C for fastening brackets to dots.
To install an Exterior Dot-HP™ on a surface using a mounting profile:
1. See Figure 4. Fasten each dot A to a mounting profile bracket B using the four screws C supplied.
2. For each mounting profile, obtain two grade 8.8 or better M6 (quarter-inch) fasteners (screws,
screwbolts, etc.) and screw plugs. Check that fasteners are suitable for the application and have
appropriate corrosion resistance. Apply an electrically insulating coating such as Delta Seal to fasteners
to prevent contact between the aluminum profile and the fasteners. If necessary, use electrically
insulating material to prevent contact between the aluminum profile and any other metals when the
profile is installed.
3. With reference to the mounting profile dimensions drawing on page 3, prepare two holes with centers 20
mm (0.55 in.) apart to accept the fasteners for each mounting profile. Use screw plugs if necessary for a
secure installation.
Physical installation
15
4. Fasten each mounting profile D securely to the surface or structure using two fasteners per profile.
A
B
D
C
E
F
Figure 4: Installation with a mounting profile
5. If you are going to install the dot now, apply a small quantity of Loctite 243 to the threads of the locking
bolt F (if you are going to install the dot in the profile later, apply the Loctite when you install the dot).
With the two halves of a lock E assembled as shown in Figure 4 and located in the grooves in the
mounting profile, tighten the bolt F through the mounting profile and into the lock finger-tight only.
6. Connect the dot’s input connector to the
output connector of the previous device on
the link, either directly or via a patch cable.
Make sure that all connectors are correctly
fastened together with locking rings twisted
to ensure a seal.
7. See Figure 5. Clip the dot onto the mounting
profile so that the lips on the mounting
bracket engage in the channels on both
sides of the profile as shown at G.
8. Tighten the locking bolt F to secure the dot
in the profile. The bolt accepts a 2.5 mm
Allen key or a 7 mm wrench. Tighten the bolt
to a torque of 1 Nm (0.75 ft.-lbs.) using a
torque driver or torque wrench. When you
have tightened the bolt, check that the head
of the bolt sits flat against the mounting
profile.
9. Check that the dot is held securely before
Figure 5: Installing a dot on a mounting profile
you leave it.
G
F
16
Exterior Dot-HP™ User Manual
System installation
Warning! Read “Safety information” on page 5 and “Precautions to avoid damage” on page 11
carefully before installing an Exterior Dot-HP™ system.
Warning! Connect the Exterior Dot-HP™ only to the devices and using only the Martin™ cables
specified in this manual.
Warning! Do not exceed the maximum numbers of devices that can be connected in chains and
maximum cable lengths specified in ”Protection from electric shock” starting on page 6 and in the
manuals of the other devices in the system.
Important! If using DMX, make sure that the DMX console and DC power source are at the same
earth (ground) potential, or the data signal may become saturated.
The Exterior Dot-HP™ is designed to display either Martin P3™ video or DMX-controlled lighting effects. It
automatically recognizes and responds to either a Martin P3™ or a DMX data signal. The next sections
explain how to create an Exterior Dot-HP™ installation to display P3 video data or DMX-controlled lighting
effects.
Installing a P3 system
See Figure 7 for an overview of the elements and layout of a Martin P3™ video display system.
To install a system that displays P3 video on Exterior Dot-HP™ dots, see the overview in Figure 7 and follow
these directions:
1. Make sure that no devices in the installation can be connected to AC mains power until all installation
work is complete.
2. Read “Safety information” on page 5 and “Precautions to avoid damage” on page 11.
3. Connect Exterior Dot-HP™ dots together in chains either directly using the dots’ cable tails and BBD
connectors or by adding Martin™ hybrid cables with BBD connectors (see “Cables” on page 36).
Warning! Do not exceed the maximum number of dots per chain given in “Safety limits for connecting
devices” on page 6.
4. Install a blanking cap (see “Connectors” on page 37) on the output connector of the last dot on each
chain to protect from water, dirt etc.
5. Connect each chain of Exterior Dot-HP™ dots to one of the four 4-pin female XLR hybrid (48 VDC
power + P3 data) outputs on a P3 PowerPort 1500™ using a Martin™ hybrid 4-pin male XLR to BBD
adapter cable, P/N 11840257 (see Figure 6). Alternatively, connect each chain of Exterior Dot-HP™
dots to one of the 4 outputs on a P3 PowerPort 1000 IP™.
4-pin XLR-to-BBD Input Cable, P/N 11840257
4-pin male XLR
Female BBD
DC power and
data to Exterior
Dot-HP™ chain
DC power and
data from P3
PowerPort 1500
Insert 4-pin XLR hybrid
extension
extension
cablecable
herehere
if required
if
necessary
Insert BBD-to-BBD hybrid
extension cable here if
necessary
Figure 6: Power and P3 video data input
6. If necessary, add a BBD-to-BBD extension cable between the first dot and the P3 PowerPort. Suitable
extension cables are available from Martin™ in various lengths. See “Cables” on page 36.
7. Create a P3 video data link from a Martin P3™ system controller such as the P3-100™, P3-200™,
P3-300™ or P3 PC™ to the P3 PowerPort 1500™ or P3 PowerPort 1000 IP™ (see the products’ user
manuals for details).
System installation
17
8. It is possible to connect P3 PowerPort devices in daisy-chains in a P3 network, but if you are using
multiple P3 PowerPorts in a fixed installation we recommend that you distribute the P3 signal by
connecting an unmanaged Gigabit Ethernet switch to the P3 System Controller and then connecting
each P3 PowerPort directly to the switch. This eliminates the risk of one P3 PowerPort signal failing and
causing loss of signal to the P3 PowerPorts daisy-chained behind it.
9. Connect the P3 PowerPort to AC mains power at 100 - 240 V, 50/60 Hz as described in its user manual.
10. connect the P3 system controller to AC mains power and power the controller on.
You can now configure the system at the P3 controller. See”System setup” on page 24.
AC mains power
P3 System Controller
P3 video data link (Ethernet cable)
Hybrid (DC power and data) link
AC mains
power
P3 PowerPort
Max. 4 chains per
P3 PowerPort
BBD-to-BBD extension
cables (if needed)
4pi
n
in XL
pu R
t c -to
ab -B
l e BD
P3 PowerPort
AC mains
power
Install blanking caps on all unused
female connectors at end of chains
See “Safety limits for connecting devices” on page 6 before creating a chain
Figure 7: P3 system layout
18
Exterior Dot-HP™ User Manual
Installing a DMX-controlled system
In a DMX-controlled system, an RDM-compliant DMX lighting controller sends a DMX control data signal
over a DMX link to the installation, and then over the hybrid link to the Exterior Dot-HP™ dots.
The DMX link requires DMX cable. It can be maximum 300 m (1000 ft.) in length and must run in one single
daisy-chain, but it can be extended or split into branches using an RDM-compliant amplifier/splitter such as
the Martin RDM 5.5 Splitter™ (P/N 90758150). Alternatively, you can run the DMX signal from the controller
over Ethernet cable using Art-Net protocol and convert it to a DMX-compliant signal with an Art-Net to DMX
converter.
If you would like assistance with creating a DMX link, your Martin™ supplier will be glad to advise.
The number of Exterior Dot-HP™ dots that you can control on one DMX link is limited by the number of
DMX channels the dots will use and the 512 DMX channels available in one DMX universe at the DMX
controller. Each time you have used 512 channels, you must create a new DMX link that is connected to a
new DMX universe on the controller. Note that this limit applies to the DMX link. The maximum safety limits
that apply to the chain of dots and cable (see “Safety limits for connecting devices” on page 6) take priority
and must be respected in all cases.
If you need to take the DMX signal from the end of a chain of Exterior Dot-HP™ dots, connect a DMX
Lead-out Cable (see “Cables” on page 36) to the output connector of the last dot on the chain. The
Lead-Out Cable has a 5-pin female XLR connector with standard DMX pinout (pin 1 = shield, pin 2 = data
cold/negative, pin 3 = data hot/positive, pins 4 and 5 are not used) that lets you draw off the DMX signal.
DC Power options in DMX installations
A DMX-controlled Exterior Dot-HP™ installation can be supplied with DC power from the Martin™ IP66
Power Supply Unit or from a generic external PSU (the Mean Well SP-480 48, for example).
The hardware and cables required are slightly different depending on which type of PSU you use to supply
the installation with DC power. The two different types of installation are covered in the next two sections:
• If you are using a Martin™ IP66 PSU, see ”Installing a DMX system using the Martin™ IP66 PSU” on
page 20.
• If you are using a generic 48 VDC PSU, see ”Installing a DMX system using a generic external 48
VDC PSU” on page 22.
System installation
19
Installing a DMX system using the Martin™ IP66 PSU
DMX/RDM Controller
48 VDC power
DMX link (DMX cable)
Hybrid (DC power and data) link
DMX/RDM Splitter (if used)
Martin™ IP66 PSU
Hybrid
lead-in cable,
Martin IP66 PSU
Martin™ IP66 PSU
Hybrid
lead-in cable,
Martin IP66 PSU
BBD-to-BBD
extension cable
(if needed)
BBD-to-BBD
extension cable
(if needed)
BBD-to-BBD
extension cable
(if needed)
BBD-to-BBD
extension cable
(if needed)
BBD-to-BBD
extension cable
(if needed)
BBD-to-BBD
extension cable
(if needed)
Install blanking caps on all unused
female connectors at end of chains
See “Safety limits for connecting devices” on page 6 before creating a chain
Figure 8: DMX-controlled system using the Martin™ IP66 Power Supply Unit
20
Exterior Dot-HP™ User Manual
To create a DMX-controlled installation that draws DC power from the Martin™ IP66 PSU:
1. See Figure 8 on page 20 for an overview of this type of installation
2. Make sure that no devices in the installation can be connected to AC mains power until all installation
work is complete.
3. Read “Safety information” on page 5 and “Precautions to avoid damage” on page 11.
4. Connect Exterior Dot-HP™ dots together in chains either directly using the BBD connectors on the dots’
cable tails or by adding Martin™ hybrid BBD-to-BBD extension cables (see “Cables” on page 36).
Warning! Do not exceed the maximum number of dots per chain given in “Martin™ IP66 PSU 240W
safety limits” on page 8.
5. Install a blanking cap (see “Connectors” on page 37) on the output connector of the last dot on each
chain to protect from water, dirt etc. There is no need to install DMX termination plugs, as dots have
integral DMX termination.
6. See Figure 9. Connect a Martin™ 5-pin XLR and Martin™ IP66 PSU to BBD adapter cable (P/N
11840275) to the start of each chain.
• Connect the 5-pin male XLR connector on the adapter cable to a DMX link that carries a DMX signal
from an RDM-compliant DMX controller such as the Martin M-PC™.
• Connect the male Martin™ IP66 PSU connector on the adapter cable to the DC output of a Martin™
IP66 Power Supply Unit.
• Connect the female BBD connector on the adapter cable to the male BBD connector at the start of the
chain of Exterior Dot-HP™ dots.
XLR5+Martin™ IP66 PSU-to-BBD Input Cable, 0.25 m, P/N 11840275
DC power input from
Martin™ IP66 PSU
Martin™ IP66 PSU
male connector
DMX from DMX/RDM
controller
5-pin male XLR
connector
Female BBD
To Exterior Dot-HP
chain
Figure 9: Martin™ IP66 PSU and DMX connections to an Exterior Dot-HP™ chain
7. Install a mains power cable on the Martin™ IP66 Power Supply Unit and connect it to AC mains power.
8. Apply AC mains power to the DMX controller.
You can now configure the system. See ”System setup”on page 24.
System installation
21
Installing a DMX system using a generic external 48 VDC PSU
DMX/RDM Controller
48 VDC power
DMX link (DMX cable)
Hybrid (DC power and data) link
DMX/RDM Splitter (if used)
External PSU
Hybrid DC
lead-in cable
BBD-to-BBD
extension cable
(if needed)
External PSU
Hybrid DC
lead-in cable
Inline fuse
required if PSU
does not have
8 A overcurrent
protection
BBD-to-BBD
extension cable
(if needed)
BBD-to-BBD
extension cable
(if needed)
BBD-to-BBD
extension cable
(if needed)
BBD-to-BBD
extension cable
(if needed)
BBD-to-BBD
extension cable
(if needed)
Inline fuse
required if PSU
does not have
8 A overcurrent
protection
Install blanking caps on all unused
female connectors at end of chains
See “Safety limits for connecting devices” on page 6 before creating a chain. Do not exceed
PSU output rating.
Figure 10: DMX-controlled system using a generic PSU
22
Exterior Dot-HP™ User Manual
Warning! If you decide to use any other external PSU than the Martin™ devices listed earlier in this section,
you must verify that the combination of equipment used is compliant with all applicable safety and
electromagnetic compatibility regulations.
To create a DMX-controlled installation that draws DC power from a generic PSU:
1. See Figure 10 on page 22 for an overview of this type of installation.
2. Make sure that no devices in the installation can be connected to AC mains power until all installation
work is complete.
3. Read ”Safety information” starting on page 5 and “Precautions to avoid damage” on page 11.
4. Connect Exterior Dot-HP™ dots together in chains either directly using the BBD connectors on the dots’
cable tails or by adding Martin™ BBD-to-BBD hybrid extension cables (see “Cables” on page 36).
Warning! Check the PSU’s DC output power rating in watts and the power consumption figures in watts for
Exterior Dot-HP™ dots with reference to “Generic 48 VDC external PSU safety limits” on page 8. Do not
create a chain of Exterior Dot-HP™ dots that will exceed the power rating of the DC output on the PSU.
5. Install a blanking cap (see “Connectors” on page 37) on the output connector of the last dot on each
chain to protect from water, dirt etc.
6. See Figure 11:
• If the PSU does not have constant overcurrent protection that will limit current to 8 A on the DC output
used, install an inline fuseholder with a 7.5 A fuse on the white (+ve) power wire of a Martin™ Power
and data adapter cable, XLR5 + power - BBD, 0.25 m (P/N 11840276). You can use a 30 amp
automotive-type inline fuseholder with a 7.5 A blade fuse.
• Connect the 5-pin male XLR connector on the power and data adapter cable to a DMX link that carries
a DMX signal from an RDM-compliant DMX controller such as the Martin M1™ or M-PC™.
• Connect the power wires on the power and data adapter cable to a DC output on the PSU. Connect
the white wire to positive (+ve) and the black wire to negative (-ve).
• Connect the female BBD connector on the adapter cable to the male BBD connector at the start of the
chain of Exterior Dot-HP™ dots.
Power + Data Input Cable, XLR5 + Power to BBD, 0.25 m, P/N 11840276
DMX from DMX/RDM
controller
Female BBD
5-pin male XLR
DC power from
generic 48 VDC PSU
white to +ve, black to -ve
To Exterior Dot-HP
chain
Insert 7.5 A or 8 A inline fuse
here if PSU does not have 8 A
overcurrent protection
Figure 11: Generic PSU and DMX connections to an Exterior Dot-HP™ chain
7. Apply AC mains power to the external PSU.
8. Apply AC mains power to the DMX controller.
You can now configure the system. See ”System setup”on page 24.
System installation
23
System setup
Warning! Read “Safety information” on page 5 and “Precautions to avoid damage” on page 11
before applying power to an Exterior Dot-HP™ installation.
Setting up for P3 display
A Martin P3™ system allows video to be displayed on an installation that consists of or includes Exterior
Dot-HP™ dots. When a P3 controller is connected to the data link and the installation is powered on, you
can set up all the devices on the link from the P3 controller. See the P3 controller user manual for details.
Setting up for DMX control
A DMX system gives 0 - 100% variable intensity control. Varying the intensity of red, blue and green LEDs in
RGB products gives RGB color mixing.
You can set up and control an Exterior Dot-HP™ installation over the data link using an RDM-compatible
DMX controller such as the Martin M-PC™ Windows application (running on a PC connected to a
USB/DMX interface such as the Martin M-DMX Interface Box) the Martin M1™ DMX/RDM control console.
The interface on the Martin M1™ monitor screen is basically identical to the Martin M-PC™ interface.
DMX control channels
DMX controllers send control data to devices over DMX control channels in DMX universes. One DMX
universe has 512 channels available. Multiple dots can share the same DMX channels if you want grouped
control and identical dot behavior.
The Exterior Dot-HP™ can be controlled using two DMX modes (see under “DMX protocols” on page 33):
• In RGB mode, each dot uses three DMX channels.
• In Basic mode, each dot uses ten DMX channels.
Different modes can be mixed freely in an installation. For example, some Exterior Dot-HP™ dots can be
set to RGB mode and others to Basic mode. All you need to do is set up dots, DMX addresses and DMX
channel allocation correctly.
DMX addresses
To prepare an installation for DMX control, you set it up using an RDM-compliant DMX controller so that
dots or pixels receive instructions from the controller on their own DMX channels. The DMX address (also
known as the control address or start channel) is the first of these channels. An Exterior Dot-HP™ dot or
pixel uses more than one channel, so it uses the DMX address channel and the channels immediately
above it. For example, one Exterior Dot-HP™ dot set to RGB mode and set to DMX address 1 will use DMX
channels 1 - 3. Channel 4 will be available for use as a DMX address for the next device.
24
Exterior Dot-HP™ User Manual
RDM
Using an RDM-compliant DMX controller such as Martin M-PC™, you can communicate with the Exterior
Dot-HP™ dots on the DMX data link via RDM. You can:
• Retrieve data from dots
• Set the DMX addresses of the dots and set their DMX mode
• Reset dots
To use Martin M-PC, connect a PC running this application to the data link using the Martin M-DMX
USB/DMX interface box.
The Exterior Dot-HP™ responds to the RDM parameter IDs listed in Table 5.
GET
allowed
RDM parameter IDs
SET
allowed
Category – Network Management
DISC_UNIQUE_BRANCH
DISC_MUTE
DISC_UN_MUTE
Category - Product Information
DEVICE_INFO

DEVICE_MODEL_DESCRIPTION

MANUFACTURER_LABEL

DEVICE_LABEL

SOFTWARE_VERSION_LABEL


Category - DMX512 Setup
DMX_PERSONALITY

DMX_PERSONALITY_DESCRIPTION

DMX_START_ADDRESS

SLOT_DESCRIPTION



Category - Control

IDENTIFY_DEVICE


RESET_DEVICE
Table 5: RDM communication with the Exterior Dot-HP™
RDM
25
Using the Exterior Dot-HP™
Warning! Read “Safety information” on page 5 and “Precautions to avoid damage” on page 11 on
before applying power to the Exterior Dot-HP™.
Do not use the Exterior Dot-HP™ if the ambient temperature exceeds 55° C (131° F) or falls below -20° C
(-4° F).
Thermal regulation
The Exterior Dot-HP™ dot has a protective thermal shutdown feature that blacks out the dot if it exceeds its
permitted maximum operating temperature.
To avoid unexpected blackouts due to thermal shutdowns but also avoid overheating that may damage the
product, the Exterior Dot-HP™ offers various options for managing temperature:
• During P3 video operation, you can enable the thermal regulation feature available in the software of all
Martin P3 system controllers. When this feature is active, Exterior Dot-HP™ dots begin to reduce their
light output when the ambient temperature reaches 45° C in order to control dot temperature. Output is
reduced gradually as the ambient temperature rises above 45° C. Dots will still light at the maximum
ambient temperature of 55° C, but output will be considerably reduced. This option avoids blackouts due
to protective thermal shutdowns.
• During P3 video operation, you can disable the P3 controller thermal regulation feature. If you choose to
do this, Exterior Dot-HP™ dots will not reduce their light output when the ambient temperature reaches
45° C, but if you drive dots hard when the ambient temperature approaches or exceeds 55° C, dots may
black out completely due to protective thermal shutdown.
• During DMX operation, the Exterior Dot-HP™ dots begin to reduce their light output when the ambient
temperature reaches 45° C in order to control dot temperature. Output is reduced gradually as the
ambient temperature rises above 45° C. Dots will still light at the maximum ambient temperature of 55° C,
but output will be considerably reduced. This option avoids blackouts due to protective thermal
shutdowns.
P3 display
The Exterior Dot-HP™ can display video from all common video sources. The video signal must be sent to
a Martin P3™ controller and then distributed to dots. The P3™ controller lets you map, configure and
control an installation containing Exterior Dot-HP™ dots (and other Martin P3™ video display products if
you have them). See the P3 controller documentation for details.
DMX control
The Exterior Dot-HP™ can display effects controlled by DMX. Three DMX modes are available:
• RGB mode uses three DMX channels and gives RGB color mixing of all the pixels on a dot.
• Basic mode uses ten DMX channels and gives RGB color mixing, strobe effects and pre-programmed
dynamic effects.
See “DMX protocols” on page 33 for full details of DMX control.
An RDM-compatible DMX controller is required so that you can address and configure the dots. See the
DMX/RDM controller documentation for details.
26
Exterior Dot-HP™ User Manual
Magnetic ‘control button’
A magnetic sensor is embedded inside the Exterior
Dot-HP™ behind the label on the back of the dot (see C in
Figure 1 on page 12). The sensor acts as a control button.
To activate the sensor, swipe a magnet past the side of
the dot near where the input cable tail enters the dot.
You may find it convenient to use the Martin Test Tool (see
“Accessories” on page 36), which contains a magnet.
Figure 12: Test Tool with magnet
Activating the magnetic sensor lets you display the
product’s status, test the LEDs and reset the Exterior
Dot-HP™ as explained in the following table.
Status display
To display a Exterior Dot-HP™ dot’s status, swipe the magnet over the sensor once. The LEDs on the dot
will give one of the indications listed in the tables below for a few seconds.
Exterior Dot-HP™ RGB
Color
Output
Indication
Action required
Blue
Constant
Busy (e.g. booting up or writing to
flash memory).
Wait a moment for normal operation
to be resumed.
Red
Constant
Error. The Exterior Dot-HP™ has
encountered a fatal error and can
not run.
Perform a factory reboot, followed by
a firmware upload if necessary.
Red
Flashing
No control source detected.
Connect a P3 system controller or
DMX controller to the network.
Green
Flashing
Ready. Exterior Dot-HP™ connected
to P3 controller but not mapped onto
the canvas.
Set up the P3 controller to use the
Exterior Dot-HP™.
Green
Constant
Running normally in P3 mode.
None.
Cyan
Flashing
Ready. Exterior Dot-HP™ in DMX
mode but not receiving valid DMX
data signal.
Send DMX data (if flashing cyan
continues although you are sending
data, check that DMX controller is
connected and configured with dot’s
DMX address).
Cyan
Constant
Running normally in DMX mode.
None.
Table 6: Status information, Exterior Dot-HP™ RGB
Using the Exterior Dot-HP™
27
Exterior Dot-HP™ CW
No. of
LEDs
Output
Indication
Action required
1
Constant
Error. The Exterior Dot-HP™ has
encountered a fatal error and can
not run.
Perform a factory reboot, followed by
a firmware upload if necessary.
1
Flashing
No control source detected.
Connect a P3 system controller or
DMX controller to the network.
2
Constant
Running normally in P3 mode.
None.
2
Flashing
Ready. Exterior Dot-HP™ connected
to P3 controller but not mapped onto
the canvas.
Set up the P3 controller to use the
Exterior Dot-HP™.
3
Constant
Running normally in DMX mode.
None.
3
Flashing
Ready. Exterior Dot-HP™ in DMX
mode but not receiving valid DMX
data signal.
Send DMX data (if flashing
continues although you are sending
data, check that DMX controller is
connected and configured with dot’s
DMX address).
4
Constant
Busy (e.g. booting up or writing to
flash memory)
None.
Table 7: Status information, Exterior Dot-HP™ CW
Testing, rebooting and returning to defaults
The tables below list the functions of the magnetic ‘control button’ on each Exterior Dot-HP™ dot.
Test patterns are stored in onboard memory. This lets you test the LEDs without an external controller, but
test patterns can also be called up on P3 system controllers, the P3 PowerPort 1500™ and the P3
PowerPort 1000 IP™.
Exterior Dot-HP™ RGB
Action
Quick swipe
Function
The first swipe displays status as shown in Table 6 for a few seconds.
The next swipes display the following test patterns on the LEDs (each
swipe scrolls to the next pattern):
- Calibrated white
- Full red
- Full green
- Full blue
- Scrolling gradient
- Dimmed (20% uncalibrated white)
Hold magnet over
‘button’ until LEDs
light blue
Reboot the Exterior Dot-HP™.
Hold magnet over
‘button’ until LEDs
light white
Return the Exterior Dot-HP™ to its default factory firmware.
Table 8: Magnetic ‘control button’ functions, Exterior Dot-HP™ RGB
28
Exterior Dot-HP™ User Manual
Exterior Dot-HP™ CW
Action
Quick swipe
Function
The first swipe displays status as shown in Table 6 for a few seconds.
The next swipes display the following test patterns on the LEDs (each
swipe scrolls to the next pattern):
- Calibrated white
- Full red
- Full green
- Full blue
- Scrolling gradient
- Dimmed (20% uncalibrated white)
Hold magnet over
‘button’ until 4 LEDs
light
Reboot the Exterior Dot-HP™.
Hold magnet over
‘button’ until 3 LEDs
light
Return the Exterior Dot-HP™ to its default factory firmware.
Table 9: Magnetic ‘control button’ functions, Exterior Dot-HP™ CW
Using the Exterior Dot-HP™
29
Service and maintenance
Warning! Read “Safety information” on page 5 and “Precautions to avoid damage” on page 11
before carrying out service on the Exterior Dot-HP™.
Warning! Lock out AC mains power to the installation before servicing.
Warning! Refer any service operation not described in this manual to a qualified service technician.
Important! Excessive dirt buildup causes overheating and may damage the product. Damage
caused by inadequate cleaning is not covered by the product warranty.
The user will need to clean the Exterior Dot-HP™ periodically. All other service operations on the Exterior
Dot-HP™ must be carried out by Martin Professional™ or its approved service agents.
Installation, on-site service and maintenance can be provided worldwide by the Martin Professional Global
Service organization and its approved agents, giving owners access to Martin’s expertise and product
knowledge in a partnership that will ensure the highest level of performance throughout the product’s
lifetime. Please contact your Martin supplier for details.
Cleaning
Cleaning schedules vary depending on the operating environment. It is therefore impossible to specify
precise cleaning intervals for the Exterior Dot-HP™. Environmental factors that may result in a need for
frequent cleaning include airborne dust and pollution.
Inspect products frequently to see whether cleaning is necessary. If in doubt, consult your Martin™ dealer
about a suitable maintenance schedule.
To clean the product, use warm water and a soft brush or a low-pressure or medium-pressure water jet. Use
car shampoo to help remove dirt and grease. If possible, dry with a soft cloth to avoid streaking. Do not use
a stiff brush or scouring pad. Do not use solvents or abrasives.
Condensation and pressure relief valve
Under certain conditions, condensation may become visible under optical components. This is normal and
harmless. Any condensation will gradually be expelled by the dot's Gore-Tex pressure relief valve (see
Figure 2 on page 14) as the dot goes through power off/on cycles.
Make sure that the pressure relief valve is clean and unblocked. The valve must be able to breathe freely so
that it can equalize pressure and expel water vapor. If a valve becomes blocked, excessive pressure can
damage seals or cause air and water to be sucked along cables and into the dot.
Water on the valve membrane will block the membrane's micropores. Do not allow water to collect on or
near valves. If you suspect that a valve has become blocked with dirt, contact your Martin supplier.
LED performance
Martin™ use the best components available, but the characteristics of all LEDs change gradually over many
thousands of hours of use. Not all colors change at the same rate, and rates of change vary depending on
factors such as temperature and how intensively a particular color is used. Because of the changes, overall
light output and the exact hues obtained from specific color mixes in all LED-based products can be
expected to shift slightly over time.
To help you obtain consistent output despite these changes, Martin™ P3 software from version 4.1.0
contains the P3 Dot Adjuster tool. This feature lets you compensate for changes in LED characteristics and
restore initial output and color authenticity levels. Please contact Martin™ for more details.
30
Exterior Dot-HP™ User Manual
Installing new software
It may be necessary to upload new software (i.e. device firmware) to the Exterior Dot-HP™ if it appears to
have a software-related fault or if you want to update to a newer software version.
Software for Martin™ products is available from the Martin™ website. The Exterior Dot-HP™ software can
be installed from the P3 System Controller over the P3 data link. You will need a Martin P3 PowerPort
1500™ or a Martin P3 PowerPort 1000 IP™ for this. See the P3 System Controller user manual for software
installation instructions.
Service and maintenance
31
Troubleshooting
Problem
Control is lost and activating
magnetic ‘control button’ causes
Exterior Dot-HP™ to show
constant or flashing red status
indication.
Product seems completely
dead.
Exterior Dot-HP™ does not
display as intended.
Probable cause(s)
Remedy
Error has occurred.
Check that system is correctly connected, set up
and running.
Hold magnet over ‘control button’ until LEDs 1 - 4
turn blue, then move magnet away, to reboot
Exterior Dot-HP™.
Restart P3 or DMX controller.
Product has gone into thermal protection
shutdown.
Check product temperature readouts on P3 system
controller. Reduce ambient temperature by
providing ventilation or fan cooling, for example.
No DC power to product.
Check 48 VDC power supply and cables
Internal fault.
Disconnect from power. Do not attempt repairs
yourself. Contact Martin™ Service or an authorized
Martin™ service partner for assistance.
Fault in 48 VDC power transmission.
Inspect connections and cables. Correct poor
connections. Repair or replace damaged cables.
Fault in data transmission.
Inspect connections and cables. Correct poor
connections. Repair or replace damaged cables.
If using DMX, check that DMX console and DC
power supply unit are at same earth (ground)
potential.
Incorrect mapping or addressing of products.
Check product address and controller settings.
Product in installation is defective and is
disturbing data transmission.
Substitute known good products one at a time until
normal operation is regained. Have faulty product
serviced by Martin™ Service.
Table 10: Troubleshooting
32
Exterior Dot-HP™ User Manual
DMX protocols
RGB Mode
Channel
1
2
3
DMX Value
Function
0 - 255
Red
0 → 100%
0 - 255
Green
0 → 100%
0 - 255
Blue
0 → 100%
Table 11: DMX Protocol, RGB Mode
Basic Mode
Channel
DMX Value
1
0 - 65535
2
3
0 - 49
50 - 200
201 - 210
211 - 255
Function
Dimmer fade (MSB)
8-bit coarse control, closed 0% → open 100%
Dimmer fade (LSB)
16-bit fine adjustment, closed → open
Strobe
No strobe
Strobe, slow → fast
No strobe
Random strobe, slow → fast
0 - 255
Strobe duration
0 → 1 second
5
0-7
8 - 255
FX selection
No FX: output controlled on RGB channels
FX selection (see “Pre-programmed FX” on page 34)
6
0 - 126
127 - 128
129 - 255
FX speed / modifier (depending on effect)
Fast → slow
Stop
Slow → fast
0
1
2
3 - 34
35
36
37 - 100
101 - 120
121 - 140
141 - 255
FX synchronization
No sync
Dot offset 10°
Dot offset 10°
...
Dot offset 350°
Synchronized
No function (reserved for future use)
Random start
Random duration
No function (reserved for future use)
4
7
8
9
10
0 - 255
Red
0 → 100%
0 - 255
Green
0 → 100%
0 - 255
Blue
0 → 100%
Table 12: DMX Protocol, Basic Mode
DMX protocols
33
Pre-programmed FX
Select the FX in this table on channel 5 in Basic Mode.
Set FX execution speed on channel 6.
Synchronize and set offsets between dots on channel 7.
Channel
DMX Value
0
5
Function
No FX
1
2
3
4
5
6
7
8
9
10
11
12
13 - 19
20
21
22
23
24 - 50
Intensity FX
Wave
Step
Pulse
Blackout strobe
2x strobe
3x strobe
4x strobe
Up, down flash
Up, flash, down, flash
Random levels
Pixel killer
Noise overlay
No function (reserved for future use)
Movie flicker
Electric arc
Atomic lightning
Thunderstorm
No function (reserved for future use)
51
52
53
54
55
56
57
58
59
60
61
62
63 - 68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87-100
Color FX
Rainbow wave
Rainbow step
Rainbow pulse
RGB wave
RGB step
RGB pulse
CMY wave
CMY step
CMY pulse
Random mix wave
Random mix step
Random mix pulse
No function (reserved for future use)
Solid
Spectrum shifter
RGB to white wave
RGB to white step
RGB to white pulse
RGB to white strobe
Normal to white wave
Normal to white step
Normal to white pulse
Normal to white strobe
Video to RGB wave
Video to RGB step
Video to RGB pulse
Video to RGB strobe
Video to video + RGB wave
Video to video + RGB step
Video to video + RGB pulse
Video to video + RGB strobe
No function (reserved for future use)
Table 13: Pre-programmed FX
34
Exterior Dot-HP™ User Manual
Specifications
Physical
Diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72 mm (2.9 in.)
Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 mm (1.4 in.) not including front
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.3 kg per meter (0.7 lbs. per ft.)
Control and Programming
Control options. . . . . . . . . . . . . . . . . . .Martin P3™ System Controller (via Martin P3 PowerPort 1500™ or
P3 PowerPort 1000 IP™) and/or DMX/RDM
Protocol detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic
Control modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .RGB, basic
DMX channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3/10
Setting and addressing . . . . . . . . . . . . . . . . . . Martin P3™ System controller or RDM-compliant controller
Control resolution. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-bit (P3) or 8-bit (DMX) control of each color
Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Color and intensity for each Dot
DMX compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . USITT DMX512-A
RDM compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ANSI/ESTA E1.20
Firmware update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Via Martin P3™ System controller
Control/User Interface
Device status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Multi-color visual indication
Device test and reset . . . . . . . . . . . . . . . . . . . . . . . Magnetic pushbutton to call up dot status and reset dot
Optics
Options
Clear front
Dome front
Directional front (TIR lens)
Minimum LED lifetime . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 000 hours (to >70% luminous output)*
Color resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 bits per color (48 bits per pixel)
*Figure obtained under manufacturer's test conditions
Viewing angle
Clear front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103° x 103° (FWHM)
Dome front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125° x 125° (FWHM)
Directional front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBA
Photometric Data
Total output
Clear front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 lumens
Dome front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 lumens
Directional front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBA
For full photometric data, see the Martin website at www.martin.com
Video Processing
Brightness control
Gamma correction and control
Color temperature control
Color space control
Calibration processing
Synchronization
Signal Protocol
Martin P3™ system (via Martin P3™ PowerPort) or DMX/RDM
Specifications
35
Construction
Base. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cast aluminum
Color . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Clear anodized (custom colors available by special order)
Protection rating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IP66
Impact resistance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IK05
Corrosion resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . C5-M (very high corrosivity / marine, ISO 12944)
RoHS compliant
Installation
Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Any
Mounting options . . . . . . . . . . . Direct surface mount, optional mounting plate or optional mounting profile
Connections
Power and data input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-pin custom BBD-type IP66-rated
Power and data thru. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-pin custom BBD type IP66-rated
Hot-plugging compatible
Electrical
Nominal input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 VDC +/- 4%
Power supply options . . . . . . . . . . . . . . . . . . Martin P3™ PowerPort 1500, Martin P3™ PowerPort 1000 IP,
Martin™ IP66 Power Supply Unit or generic 48 VDC PSU
Power Consumption
Typical total power consumption, calibrated mode . . . . . . . . . . . . . . . . . . . . . 5 W at full intensity, full white
Typical total power consumption, uncalibrated mode . . . . . . . . . . . . . . . . . . . 7 W at full intensity, full white
Allow for +/-10% variation in power consumption figures
Thermal
Cooling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Convection
Maximum ambient temperature (Ta max.) for typical video content. . . . . . . . . . . . . . . . . . . . 55° C (131° F)
Minimum ambient temperature (Ta min.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -20° C (-4° F)
Max. total heat dissipation, calculated, +/- 10%. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 BTU/hr.
Approvals
EU safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .EN 60950-1, EN 60950-22
EU EMC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EN 55022, EN 55024
US safety (pending) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UL 60950-1, UL 60950-22
US EMC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .CFR Title 47 Part 15 Class A
Canadian safety (pending) . . . . . . . . . . . . . . . . .CSA C22.2 No. 60950-1, No. 60950-22
Canadian EMC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ICES-003 Class A
Australia/NZ (pending) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .RCM
Accessories
Magnetic Test Tool, set of 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 91610139
Mounting hardware
Surface Mounting Plate, aluminum, Exterior Dot-HP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 91606020
Mounting Profile, Exterior Dot-HP (including dot bracket, screws and lock) . . . . . . . . . . . . . P/N 91606021
Mounting Profile Locks, set of 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 91611725
Cables
Power + Data Input Cable, 4-pin male XLR (for P3 PowerPort 1500) to fem. BBD, 0.25 m. . P/N 11840257
Power + Data Input Cable, 5-pin male XLR + wire tails (for PSU) to female BBD, 0.25 m . . P/N 11840276
Power + Data Input Cable, 5-pin male XLR + male Martin™ IP66 PSU to fem. BBD, 0.25 m P/N 11840275
Power + Data Extension Cable, Installation type CMX, BBD-BBD 1 m . . . . . . . . . . . . . . . . . P/N 11840270
Power + Data Extension Cable, Installation type CMX, BBD-BBD, 2.5 m . . . . . . . . . . . . . . . P/N 11840271
Power + Data Extension Cable, Installation type CMX, BBD-BBD, 5 m . . . . . . . . . . . . . . . . P/N 11840272
Power + Data Extension Cable, Installation type CMX, BBD-BBD, 10 m . . . . . . . . . . . . . . . P/N 11840273
Power + Data Extension Cable, Installation type CMX, BBD-BBD, 25 m . . . . . . . . . . . . . . . P/N 11840274
Power + Data Extension Cable, Installation type CMX, without connectors, 100 m . . . . . . . P/N 11840278
DMX Leadout Adapter, male BBD to 5-pin female XLR, 0.25m. . . . . . . . . . . . . . . . . . . . . . . P/N 11840258
36
Exterior Dot-HP™ User Manual
Connectors
Power + Data Cable Connector, BBD, Male. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 91611750
Power + Data Cable Connector, BBD, Female . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 91611751
Blanking caps for sealing unused female BBD connectors, set of 10 . . . . . . . . . . . . . . . . . . P/N 62409876
Related Items
Martin P3™ PowerPort 1500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Martin P3™ PowerPort 1000 IP, Installation model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Martin™ IP66 PSU 240 W external power supply unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Martin P3-050™ System Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Martin P3-150™ System Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Martin P3-300™ System Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Martin P3-PC™ System Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
P/N 90721040
P/N 90721080
P/N 90760330
P/N 90721090
P/N 90721015
P/N 90721060
P/N 90721030
Ordering Information
Exterior Dot-HP™ RGB
Exterior Dot-HP™ RGB, Aluminum, Clear Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 90357683
Exterior Dot-HP™ RGB, Aluminum, Diffuser Dome Front . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 90357685
Exterior Dot-HP™ RGB, Aluminum, Directional Front (TIR Lens) . . . . . . . . . . . . . . . . . . . . . P/N 90357686
Exterior Dot-HP™ Cool White
Exterior Dot-HP™ Cool White, Aluminum, Clear Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 90357688
Exterior Dot-HP™ Cool White, Aluminum, Diffuser Dome Front . . . . . . . . . . . . . . . . . . . . . . P/N 90357687
Exterior Dot-HP™ Cool White, Aluminum, Directional Front (TIR Lens) . . . . . . . . . . . . . . . . P/N 90357689
Specifications subject to change without notice. For the latest product specifications, see www.martin.com
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Canadian Interference-Causing Equipment Regulations - Règlement sur le Matériel Brouilleur du Canada
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le Matériel Brouilleur du Canada.
EU EMC
Warning! Class A ITE product. Operation of this equipment in a residential environment could cause radio interference.
Not for use in a computer room as defined in the Standard for the Protection of Information Technology Equipment, ANSI/NFPA 75.
Ne peut être utilisé dans une salle d'ordinateurs telle que définie dans la norme ANSI/NFPA 75 Standard for the Protection of
Information Technology Equipment.
Disposing of this product
Martin™ products are supplied in compliance with Directive 2002/96/EC of the European Parliament and of the
Council of the European Union on WEEE (Waste Electrical and Electronic Equipment), as amended by Directive
2003/108/EC, where applicable.
Help preserve the environment! Ensure that this product is recycled at the end of its life. Your supplier can give
details of local arrangements for the disposal of Martin products.
Specifications
37
www.martin.com • Olof Palmes Allé 18 • 8200 Aarhus N • Denmark
Tel: +45 8740 0000 • Fax +45 8740 0010
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement