PRECAUTIONS SYSTEM CONNECTIONS PARTS IDENTIFICATION

PRECAUTIONS SYSTEM CONNECTIONS PARTS IDENTIFICATION
COMPACT DISC PLAYBACK
GENERAL OPERATION
PRECAUTIONS
Follow the advice below for safe and appropriate operations.
ON PLACEMENT
ON SAFETY
• Do not use the unit in places
which are extremely hot,
cold, dusty, or humid.
• Place the unit on a flat and
even surface.
• Do not restrict the air flow of
the unit by placing it in a
place with poor air flow, by
covering it with a cloth, or by
placing it on a carpet.
• When
connecting
or
disconnecting the AC cord,
grip the plug and not the
cord itself. Pulling the cord
may damage it and create
hazard.
• When you are not going to
use the unit for a long
period of time, disconnect
the AC power cord.
ON AC VOLTAGE
ON CONDENSATION
• Before use, check that the
rated voltage of your unit
matches your local voltage.
• When left in a heated room
where it is warm and damp,
water
droplets
or
condensation may form
inside the CD player.
• When there is condensation
inside the unit, the unit may
not function normally.
• Let it stand for 1 to 2 hours
before turning the power on,
or gradually heat the room
up and dry the unit before
use.
FCC INFORMATION (FOR USA
ONLY)
This device complies with Part
15 of FCC Rules.
Operations are subject to the
following two conditions:
(1) This device may not c a u s e
harmful interference, and (2)
This device must accept
a n y interference received,
including interference that may
cause undesirable operations.
Should any trouble occur,
disconnect the AC power
cord and refer servicing to
qualified personnel.
SYSTEM CONNECTIONS
SPEAKERS CONNECTING
• Connect the wires to the speaker terminals in correct position.
• Connect speakers other than the speakers supplied with the
unit may damage the unit.
AC POWER CONNECTING
• Before use, check that the rated voltage of your unit
matches your l o c a l v o l t a g e . M a k e s u r e s p e a k e r s a r e
connected correctly before plugging the AC power cord
into an AC outlet.
CAUTION :
• Be sure the AC power cord is disconnected and all functions
are off before making connections.
4. Press the OPEN/CLOSE button to close the disc tray. It takes a
short while for your player to check the discs.
COMPACT DISC (CD) DISPLAY
1. REPEAT mode indicator
2. DISC indicator
3. Playback indicator
4. Pause indicator
5. Track indicator
5. Press the DISC SKIP button to select the desired disc. Press
either one of the SKIP/SEARCH buttons to select the desired
track.
6. Press
PLAY/PAUSE button to start playback.
SOUND ADJUSTMENT
TO ADJUST THE VOLUME
To stop playing:
a) For a moment only, press
PLAY / PAUSE button and " " will
be displayed. Press this button again to resume playing.
b) Press CD STOP button.
Adjust the VOLUME control to obtain the
desired volume level.
FOR PERSONAL LISTENING
Connect headphones (Ø3.5mm stereo mini
plug) to the PHONES jack.
Adjust the VOLUME for the desired listening level.
When headphones are connected, the speakers are automatically disconnected.
WHEN RECORDING
The VOLUME controls switch on may be adjusted with no effect
on the recorded signal.
NOTE:
• To locate a track of currently selected disc, press
or
SKIP/SEARCH button repeatedly.
• To locate a track of another disc, press DISC SKIP button to
get to desired disc first and then press
or
SKIP/
SEARCH button repeatedly.
• To search a track, keep
or
SKIP/SEARCH button pressed
and release it at desired point.
RADIO OPERATION
1. Set the FUNCTION switch to
TUNER.
2. Select the desired band.
REVERSE
SKIP
FORWARD
SKIP
PRESS IT REPEATEDLY
3. Tune into a station.
4. Adjust the volume.
2
REVERSE
SEARCH
FORWARD
SEARCH
KEEP IT PRESSED
CD REPEAT PLAYBACK
REPEAT PLAYBACK - DURING PLAYBACK MODE
1
• TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF
PLUG TO WIDE SLOT, FULLY INSERT (FOR USA AND CANADA
ONLY).
FM ANTENNA
• Do not connect to an outside antenna.
PARTS IDENTIFICATION
To repeat the current track
• Press REPEAT ONE/DISC button until REPEAT ONE appears
on the CD display and the currently playing track will be played
repeatedly until the stop button is pressed.
• Press
or
SKIP buttons with repeat function on, repeat
can still skip through different track of the currently selected
disc.
RADIO OPERATION
FOR BETTER RECEPTION
Fully unwind the wire
antenna. Then extend the
wire antenna and place it in
the position that sound best.
Rotate the unit to get the
best receiving position.
NOTE:
DO NOT CONNECT FM
ANTENNA WIRE TO OUTSIDE
ANTENNA.
AM / MW
To repeat the whole disc
• Press REPEAT ONE/DISC button until REPEAT ONE DISC appears
on the CD display and the current disc will be played repeatedly
starting from the currently playing point.
• Press
or
SKIP buttons with REPEAT ONE/DISC function
on, one can still search through the whole disc, and the player
may start playing from the selected point.
FM
TO RECEIVE THE FM BROADCAST IN STEREO
Set the Mode selector to FM.ST.
When the FM STEREO broadcast is received, FM STEREO indicator
lights up.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
CD door
POWER STANDBY indicator
ON indicator
VOLUME control
FM STEREO indicator
FUNCTION switch (ST.BY/TAPE/TUNER/CD)
PHONES jack
CD OPEN/CLOSE button
CD REPEAT ALL DISC button
CD REPEAT ONE/DISC button
CD STOP button
Cassette holder
CD display
TUNING control
Remote sensor
Mode selector (BEAT CUT / FM MODE)
BAND selector (FM/AM)
DISC SKIP button
CD SKIP/SEARCH button
CD PLAY/PAUSE button
Cassette operation controls
REC button
PLAY button
REWIND button
F.FWD (fastforward) button
STOP / EJECT button
PAUSE button
IF THE FM BROADCAST SIGNAL IS WEAK
Set the Mode selector to FM MONO position to turn off the FM
STEREO indicator and background noises become monaural.
To repeat all disc
• Press REPEAT ALL DISC button until REPEAT ALL DISC
appears on the CD display.
• Press on
/
SKIP buttons can make the player start playing
from the newly selected point of the currently playing disc.
• Press on DISC SKIP button can make the player start playing
from the first track of the newly selected disc. The
/
SKIP buttons can be used to choose a particular track on this
selected disc, the player will then start playing from that point.
AFTER LISTENING
Set the FUNCTION switch to ST.BY (Standby).
COMPACT DISC PLAYBACK
1. Set the FUNCTION switch
to CD.
2. Press the OPEN/CLOSE button to
open the disc tray. Place the first
disc onto the disc holder, with
the label side up.
To cancel repeat play
• Press either one of the REPEAT buttons until the word 'REPEAT'
disappears from the CD display.
ATTENTION - If the CD player does not operate properly
3. Press the DISC SKIP button to revolve the tray clockwise.
Place other disc(s) on the disc holder(s).
WARNING: Take out all discs from the disc tray before
transportation.
1. Slide the FUNCTION switch
from CD to ST.BY (Standby).
2. Slide the FUNCTION switch
from ST.BY to CD.
1. Set the FUNCTION switch to
TAPE.
2. Press the STOP/EJECT
button.
TO CHANGE REMOTE BATTERY
1. Open the battery
door.
3. Insert a cassette tape into
the cassette compartment.
5CD CHANGER
HOME STEREO SYSTEM
REMOTE CONTROL (OPTIONAL)
TAPE PLAYBACK
OPERATING INSTRUCTIONS
2. Insert one
CR2025 (3V)
size battery.
ATTENTION
Ta k e o u t t h e P V C
sheet before operating the Remote
Control.
4. Press the PLAY button to
begin playback.
BATTERY REPLACEMENT
When battery become weak, the operating distance of the
Remote Control is greatly reduced and you will need to
replace the battery.
TO STOP PLAYBACK
WHEN THE TAPE REACHES
Press the STOP / EJECT button. ITS END
During fast wind or regular
TO INTERRUPT PLAYBACK
play, the tape will automatically
Press the PAUSE button.
be stopped when its end is
To resume play, press the
reached.
PAUSE button again.
NOTE:
If the Remote Control is not to be used for a long time,
remove the battery to avoid damage caused by battery
leakage corrosion.
WARNING
MAINTENANCE
TO REWIND AND FASTWIND
Press the REW or F.FWD
button. Press the STOP /
EJECT button to stop winding
at the desired position.
CLEANING CD
If the CD skips or will not play, the disc
may need to be cleaned.
Before playing, wipe the disc from the
centre out with a cleaning cloth. After playing, store the disc in its case.
RECORDING FROM BUILT-IN TUNER
CLEANING THE TAPE HEADS
To maintain optimum sound quality, clean
the playback/record heads (a), erasure
head (b), pinch roller (c), and capstans
(d) regularly (every 10 hours of use). Use
a cotton swab lightly moistened with
cleaning fluid or denatured alcohol.
USE ONLY NORMAL (TYPE I) TAPE FOR RECORDING
RECORDING FROM THE BUILT-IN TUNER
1. Set the FUNCTION switch to
TUNER and tune to your desired
station.
2. Insert a tape.
The side you
want to record.
EXPLANATION OF GRAPHICAL SYMBOLS:
WARNING
RISK OF ELECTRIC
SHOCK DONOT OPEN
"WARNING: TO REDUCE THE
RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO
QUALIFIED
SERVICE
PERSONNEL."
The lightning flash with an arrowhead
symbol, within the equilateral triangle,
is intended to alert the user to the
presence of uninsulated "dangerous
voltage" within the product's enclosure
that may be of sufficient magnitude to
constitute an electric shock to persons.
The exclamation point within the
equilateral triangle is intended to alert
the user to the presence of important
operating and maintenance (servicing)
instructions in the literature
accompanying the appliance.
WARNING: TO
PREVENT FIRE OR SHOCK HAZARD, DO
NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
CLEANING THE UNIT
Do not use volatile chemicals on this unit.
Clean by lightly wiping with a soft cloth.
CAUTION
IMPORTANT NOTE:
If an abnormal display indication or an
operating problem occurs, disconnect the
AC power cord. Wait at least 5 seconds,
then reconnect it. Before transporting the
unit, take out all the discs from CD tray.
3. Press the RECORD button
which also engages the PLAY
button.
INVISIBLE LASER RADIATION
WHEN OPEN AND INTERLOCK
DEFEATED.
AVOID EXPOSURE TO BEAM
This product contains
a low power laser device.
CLASS 1 LASER PRODUCT
CLASS 1 LASER
PRODUCT
• If whistle is heard (beat), it may be reduced by switching the
"Beat Cut" to the other position.
RECORDING FROM CD PLAYER
TROUBLE SHOOTING GUIDE
USE ONLY NORMAL (TYPE I) TAPE FOR RECORDING RECORDING
FROM THE CD PLAYER
The following checks will assist in the correction of most
problems which you may encounter with your system.
Before going through the check list below, first check the
following points.
1. Set the FUNCTION switch
to CD.
2. Insert a tape.
The side
you want to
record.
SYMPTOM
GENERAL
No sound.
3. Press the RECORD button
which also engages the
PLAY button.
TO STOP RECORDING
Press the STOP / EJECT button.
TO INTERRUPT RECORDING
Press the PAUSE button.
To resume, press the PAUSE
button again.
4. Press the
PLAY / PAUSE
button of the CD player.
PLAY/PAUSE
TO ERASE A RECORDED
TAPE
1. Press the FUNCTION button
to TAPE.
2. Insert a tape with the side
you want to erase facing
you.
3. Press the RECORD button to
start erasing.
CAUSE (AND REMEDY)
1.
OPEN Button
2.
- SKIP Button
3. REPEAT Button
4.
+SKIP Button
5. DISC SKIP Button
6.
PLAY/PAUSE Button
7. STOP Button
No sound from one channel or
unbalanced left and right volume.
• Check the speaker connections
of the inoperative channel.
Reversed left and right sound.
• Check the speaker cord
connection and speaker location.
Lack of bass sound or apparently
imprecise physical location of
musical instruments.
• Check the speaker connection
for proper phasing.
Severe hum or noise.
• The TV or VCR is too close to
the stereo system. Separate the
stereo system from the TV or
VCR.
Specifications and external apperance are subject to
change without advance notice due to continuous product
improvement.
IMPORTANT SAFETY INSTRUCTIONS
1)
2)
3)
4)
5)
6)
7)
RADIO RECEPTION
The FM STEREO indicator flashes.
• Wire the antenna.
Severe hum or noise.
• Wire the antenna.
8)
9)
Play does not start.
•
•
•
•
Distorted playback or sound loss
during CD playback.
• Moisture condensation.
• CD disc is dirty or scratched.
The disc is not placed correctly.
Dirty disc.
The disc is inserted upside down.
The player is in the pause mode.
10)
CASSETTE DECK OPERATION
Recording cannot be made.
USING THE REMOTE CONTROL CORRECTLY
• Point the Remote Control at the REMOTE SENSOR located
on the unit.
• When there is a strong ambient light source, the
performance of the infrared REMOTE SENSOR may be
degraded, causing unreliable operation.
• The recommended effective distance for remote operation
is about 4 meters (13 feet).
Power requirements AC ~ 120V 60Hz (USA/CANADA)
AC ~ 220V 50Hz (other countries)
AC ~ 230-240V 50Hz (Europe)
AC ~ 240V 50Hz (Australia)
AC ~ 110-120V/220-240V 50/60Hz
(other countries)
Power consumption 15 W
• Turn VOLUME clockwise.
• The headphones are connected.
Disconnect them.
CD PLAYER OPERATION
REMOTE CONTROL (OPTIONAL)
SPECIFICATIONS
• No cassette in the cassette
holder.
• The tab is removed from the
cassette.
• The tape is wound completely.
11)
12)
13)
Recording or playback cannot be
made or there is a decrease in
sound level.
• Dirty head.
• Magnetic build-up on the record/
playback head.
Excessive wow or flutter, or
sound dropout.
• Contamination of the capstans
or pinch rollers.
Insufficient erasure.
• Magnetic build-up on the erase
head.
Increase of noise or erase of high
frequencies.
• Magnetic build-up on the erase
head.
14)
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers)
that produce heat.
Do not defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider
than the other. A grounding type plug has two blades and a
third grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does not fit into
your outlet, consult an electrician for replacement of the
obsolete outlet.
Protect the power cord from being walked on or pinch
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
Only use attachments/accessories specified by the
manufacturer.
Unplug this apparatus during lightening storms or when unused
for long periods of time.
Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has
been exposed to rain or moisture, does not operate normally,
or has been dropped.
This appliance shall not be exposed to dripping or splashing
water and that no object filled with liquid such as vases shall
be placed on the apparatus.
Printed in China
811-167091-011
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement