Dell PowerConnect W-7200 Series SPR-4RK-MNT
Installation Guide
The SPR-4RK-MNT four-point rack mounting kit provides the necessary hardware to securely mount a Dell
PowerConnect W-7200 Series Controller into a standard four-point 19 inches Telco rack. In this document, the
W-7200 Series controller is referred to as the “device.”
CAUTION: Each device should have its own mounting equipment. Do not place other networking equipment directly on top of a mounted device. Failure to do so can result in damage to the device.
Required Tools and Equipment
2x Rack Mount Brackets
2x Slide Rail Brackets
2x Rear Rack Mount Brackets
M4 x 8mm Phillips Head Screws (16x)
M6 x 15mm Phillips Head Screws (8x)
M3 x 6mm Phillips Head Screws (8x)
Suitable Screwdrivers for both screw types (not included)
NOTE: Some racks require screws that differ from those included with the device. Confirm that you have the correct screws before installing your device.
Installation Steps
To install a device into a four-point 19 inches (48.26 cm) rack system:
1. Place a front rack mount bracket over the mounting holes on one side of the device (see Figure 1
).
2. Secure the bracket to the device using four M4 x 8mm phillips head screws and a suitable screwdriver (see
Figure 1
).
3. Repeat these steps on the opposite side of the device.
0511263-01 | January 2013 1
Figure 1 Front Rack Mount Brackets
4. Place a slide rail bracket over the rear mounting holes on one side of the device (see
Figure 2 ).
5. Secure the bracket to the device using four M4 x 8mm phillips head screws and a suitable screwdriver.
6. Repeat these steps on the opposite side of the device.
Figure 2 Rear Rack Mount Brackets
2
7. Lift the device into place and align the front mounting brackets with the chosen mounting points in the rack
as shown in Figure 3 .
8. Secure the front mount brackets by inserting and tightening four (two per bracket) M6 x 15mm phillips head screws using a suitable Phillips Head screwdriver.
Dell PowerConnect W-7200 Series SPR-4RK-MNT | Installation Guide
Figure 3 Inserting the Rear Brackets
Figure 4 Securing the Mounting Brackets to the Rack
9. Slide the rear mounting brackets into place.
10. Secure the rear mount brackets by inserting and tightening four (two per bracket) M6 x 15mm phillips head screws using a suitable Phillips Head screwdriver (see
Figure 4
).
11. Secure the rear mount brackets to the slide rail bracket by inserting and tightening eight (four per side) M3 x
6mm phillips head screws using a suitable Phillips Head screwdriver (see
Figure 4
).
12. Ensure that the device is level by verifying that the screws on the front of the rack are aligned with those on the rear of the rack.
Dell PowerConnect W-7200 Series SPR-4RK-MNT | Installation Guide 3
13. Leave a minimum of four inches (10cm) of space on the left and right side of the unit for proper air flow and ventilation.
14. Leave additional space in front and back of the unit to access power cords, network cables, and LED status indicators.
Contacting Support
Website Support
ain Website
Main Site
Support Site
Documentation Site dell.com
dell.com/support dell.com/support/manuals
Copyright
© 2013 Aruba Networks, Inc. Aruba Networks trademarks include registered Aruba the Mobile Edge Company logo, and Aruba Mobility Management System trademarks of Dell Inc.
, Aruba Networks ® , Aruba Wireless Networks ®
®
, the
. Dell™, the DELL™ logo, and PowerConnect™ are
All rights reserved. Specifications in this manual are subject to change without notice.
Originated in the USA. All other trademarks are the property of their respective owners.
Open Source Code
Certain Aruba products include Open Source software code developed by third parties, including software code subject to the GNU General
Public License (GPL), GNU Lesser General Public License (LGPL), or other Open Source Licenses. The Open Source code used can be found at this site: http://www.arubanetworks.com/open_source
Legal Notice
The use of Aruba Networks, Inc. switching platforms and software, by all individuals or corporations, to terminate other vendors’ VPN client devices constitutes complete acceptance of liability by that individual or corporation for this action and indemnifies, in full, Aruba Networks, Inc. from any and all legal actions that might be taken against it with respect to infringement of copyright on behalf of those vendors.
4 Dell PowerConnect W-7200 Series SPR-4RK-MNT | Installation Guide
