opticlink CL-Full+
opticlinkTM CL-Full+
Product Information
March 2009
rev. 0309-1.00
Fiber Optic CameraLinkTM video transmission
second
generation
© 2009 ARVOO Imaging Products BV, all mentioned trademarks and registered trademarks are acknowledged.
Specifications, models and options are subject to changes without any notice by ARVOO Imaging Products BV.
*compact model
*lower power
*lower costs
TYPICAL APPLICATIONS:
a
Long haul Imaging Applications
a
Harsh Environment Machine Vision
a
Intelligent Traffic Control Systems
a
Medical X-ray Imaging Equipment
a
Aircraft/ UAV Vision Systems
a
Naval/Submarine Vision Systems
a
Military Test Site Applications
a
Secure Video Links
a
Deep Sea Investigation
a
Remote Monitoring Space Observation
supports CameraLink Full-plus
10-taps = 80 data bit @ 85 MHz
over one duplex optical fiber
INTRODUCTION:
The opticlinkTM CL-Full+ set is the solution for long haul and for secure CameraLink
digital video transmission. The CL-Full+ model is part of the second generation of
opticlinkTM, including a 10 years experience with first generation sets used in all
kind of applications, all over the world. Please note that ARVOO Imaging Products
is the inventor of opticlinkTM.
For CameraLink digital video transmission, a copper cable can be used upto a few
meters distance between camera and frame grabber. This is too short for many
real world applications. The opticlinkTM set offers the solution by bridging a
distance of upto tens of meters, hundreds of meters or even kilometers based
on an optical fiber connection.
The opticlinkTM CL-Full+ is the only solution for reliable video links for security
systems and harsh environments, since fiber optic communication cannot be
monitored or distorted by electromagnetic noise or radiation.
The opticlinkTM CL-Full+ accepts CameraLink Base-Medium-Full-Full+
digital video and is fully transparent for the data transmission.
The CL-Full+ is housed in a strong metal enclosure and can be used
in industrial environments. For more rugged solutions, please contact
ARVOO Imaging Products BV.
ARVOO
an ARVOO imaging product
ARVOO Imaging Products BV, P.O. Box 439, 3440 AK Woerden, The Netherlands
Tel +31-348-413897 Fax +31-348-417242, Email: [email protected] Website: www.arvoo.com
Configurations
opticlinkTM CL-Full+ configurations:
any camera
any frame grabber
TM
opticlink configuration 1
fiber
RS-232
FC2F
FF2C
RS-232
TM
For opticlink configuration 1 there is a sender (FC2F) unit and a receiver
(FF2C) unit between the camera and the frame grabber. Any camera and
frame grabber that are CameraLink compatible can be used*.
any camera
TM
opticlink configuration 2
fiber
RS-232
opticlinkTM
frame grabber
with fiber input
FC2F
TM
For opticlink configuration 2 the receiver unit is replaced by an ARVOO
frame grabber with direct fiber input. Any camera that is CameraLink
compatible can be used*.
* CameraLink mode and pixelclock should match
a
multiple opticlinkTM sets can be used with one processing computer
a
opticlinkTM frame grabber boards from ARVOO Imaging Products BV are
available for PCI-X, PCI-Express and Compact PCI, for technical details
please refer to the opticlinkTM frame grabber product flyer of ARVOO
ARVOO
ARVOO Imaging Products BV, P.O. Box 439, 3440 AK Woerden, The Netherlands
Tel +31-348-413897 Fax +31-348-417242, Email: [email protected] Website: www.arvoo.com
opticlinkTM CL-Full+
Features
SYSTEM OVERVIEW of the opticlinkTM CL-Full+ Media Converter (FC2F unit)
TM
2* RS-232
connector
firmware
control unit
opticlink
parameter
detection
processor
realtime data
formatter
opticlink
transmission
protocol
engine
serial I/O
interface
TM
gigabit optical
transceiver
LC duplex fiber connector
TM
CameraLink
Full+ interface
Mini-CameraLinkTM
connectors
10 taps - 80 data bit
enhanced
error detection
processing unit
status LEDs
CameraLinkTM
interface
Base-Medium-Full-Full+
Tap A-B-C D-E-F G-H-I-J
2* SDR-26pin mini connector
area/line scan supported
Fiber Connector
Fiber Support
(order option)
One LC duplex fiber connector
Multimode, 850 nm
OM3 fiber cable recommended
Single mode*, 1310 nm
Pixel Clock
(STROBE)
20-85 MHz multimode fiber
(default temp. range)*
Electrical
6-24 V DC
6.5 Watt (mm unit) typical
Video Timing
Signals
FVAL
LVAL
DVAL
STROBE
Temperature
(default)
0 to 70 oC operating temperature
-40 to 85 oC storage temperature
Industrial temp.
(optional)
to be released, contact ARVOO
for latest availability information
Relative humidity
(non-condensing)
less then 90%
Mechanical
110*110*35 mm (unit) exclusive
connectors and screw mount
Certification
CE, RoHS
Camera Control
Signals
CC1-CC4
Serial Channel
in CameraLink
SerTFG/SerTC
115 kbps maximum
Serial Channel
via COM port
2 ports TX/RX
115 kbps maximum
external sub-D9 connector
* for single mode support, ask [email protected] for actual availability information
and current specifications
for more technical details, please refer to the User Manual
an ARVOO imaging product
ARVOO Imaging Products BV, P.O. Box 439, 3440 AK Woerden, The Netherlands
Tel +31-348-413897 Fax +31-348-417242, Email: [email protected] Website: www.arvoo.com
opticlinkTM CL-Full+
Ordering Information:
product:
order code:
Multi mode fiber model:
SET:
CL-Full+-mm
SINGLE UNITS:
FC2F-mm (camera side unit)
FF2C-mm (computer side unit)
Single mode fiber model:
SET:
CL-Full+-sm
SINGLE UNITS:
FC2F-sm (camera side unit)
FF2C-sm (computer side unit)
Your local distributor:
ARVOO
ARVOO Imaging Products BV, P.O. Box 439, 3440 AK Woerden, The Netherlands
Tel +31-348-413897 Fax +31-348-417242, Email: [email protected] Website: www.arvoo.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement