broadwave® led wall washer (hard-wire)

broadwave® led wall washer (hard-wire)
®
120V
AC
DMX
COMPATIBLE
COLOR-CHANGING
BROADWAVE® LED WALL WASHER (HARD-WIRE)
DRY/WET LOCATION
SPECIFICATION SHEET
• Extruded aluminum body &
tempered glass
• IP 65 wet/outdoor
• 150° rotary angle
• Wall and ceiling mountable
• DMX-512 controllable
Input ¹ : 100-240VAC, 50/60Hz
Power Connection: 1015 Wire, 16AWG, 600V,
105°C, VW-1
Operating Voltage: 24V DC
Power Consumption: 24.5W(18 in.), 48.5W(49 in.)
LED Chip Type: Edison
LED Chip Beam Angle: 45°
CRI: 70 (6000K)
Mounting² : (2x) integrated 150° surfacemount brackets. Each bracket has (2x) 5/16 in.
mounting holes. Wall & ceiling mountable
Maximum Run: 10 fixtures (expandable with
use of 8-Way DMX Splitter)
Connections: 1ea. male/female wet location
3-pin M14 cables (15 in. length). M14-to-XLR-3
Slide adjustable
brackets
L 17.32 or 48.82 in.
(440 or 1240mm)
SPECIFICATIONS
adapter cables also included
Dimmable ³ : May be dimmed/controlled using
on-board controls or with a compatible DMX512 controller
Ambient Temp ⁴ : -4° ~ 104° F (-20° ~ 40° C)
Operating Temp ⁵ : -4° ~ 131° F (-20° ~ 55° C)
Housing / Cooling: Extruded aluminum casing;
tempered glass / cooling by free air convection
Environment ⁶ : IP65 wet/outdoor
Dimensions: 17.32 x 3.07 x 4.73 in. (L x W x H)
48.82 x 3.07 x 4.73 in. (L x W x H)
Weight: 5.07 lbs.(18 in.), 13.01 lbs.(49 in.)
Certifications: ETL Listed Hard-Wire Luminaire.
Conforms to ANSI/UL Std. 1598. Certified to
CAN/CSA Standard CSA C22.2 No.250.0
Item #
CCT
(Kelvin)
Lumens ⁷
LED Chips
Efficacy
(lm/W)
DI-0454-ETL (49 in.)
6000K
2318
36
47.8
DI-0450-ETL (49 in.)
RGB
1203
R=12, B=12, G=12
24.8
Note ¹ Only ETL Listed for connection with a 120VAC, 15- or 20-ampere branch circuit.
Note ² When mounting to walls and ceilings, use applicable lag bolts and consider the strength of these surfaces versus the weight
of the fixture.
Note ³ Not compatible with standard High Voltage AC dimming controls.
Note ⁴ Do not install product in an environment outside the listed ambient temperature. Ensure adequate airflow and heatsinking is
considered when mounting/installing. Exceeding the maximum ambient temperature may damage LED chips by reducing the
total lamp life, lumen output, and/or adversely impact color consistency.
Note ⁵ Operating temperature is measured according to the minimum and maximum ambient temperature environment.
Note ⁶ When installing outdoors or in a damp location, ensure water-resistant end caps are connected to all wet location 3-pin M14
cables. If attaching XLR-3 DMX adapter cables seal all standard XLR-3 connections with 1.25” heat shrink and finish with
waterproof tape (not included). Do not use liquid sealants of any kind.
Note ⁷ Lumen value measured in accordance to IES LM-79-08. LED chips have a luminous flux range with a tolerance of +/- 5%.
H 4.73 in.
(120mm)
LED WALL WASHER
H 2.75 in.
(70mm)
W 3.07 in.
(78mm)
H 1.98 in.
(50mm)
150°
Rotary Angle
Item #:
BROADWAVE® SERIES
Project:
1 OF 5
SS012517-2.0
PHOTOMETRICS*
49 in. BROADWAVE 6000K
49 in. BROADWAVE RGB
DI-0454-ETL
DI-0450-ETL
POLAR CANDELA DISTRIBUTION GRAPH
180
120
150
ACROSS
45
ALONG
POLAR CANDELA DISTRIBUTION GRAPH
180
120
150
ACROSS
45
ALONG
90
1100
90
550
60
60
2200
1100
3300
1650
0
30
0
30
INTENSITY(CANDLEPOWER) SUMMARY
INTENSITY(CANDLEPOWER) SUMMARY
ANGLE ALONG
0
3825
5
3572
10
2992
15
2316
20
1691
25
1159
30
791
35
587
40
455
45
346
50
230
55
125
60
62
65
32
70
16
75
7
80
2
85
0
90
0
ANGLE ALONG
0
1892
5
1829
10
1618
15
1269
20
889
25
571
30
382
35
297
40
244
45
190
50
126
55
68
60
33
65
16
70
7
75
2
80
0
85
0
90
0
BEAM SIDE
22.5
45
3825 3825
3600 3598
3026 3042
2339 2357
1696 1706
1167 1174
796
805
588
595
452
460
342
351
225
232
122
126
61
62
31
32
16
16
7
7
2
2
0
0
0
0
67.5 ACROSS
3825 3825
3621 3547
3071 3007
2399 2359
1751 1733
1204 1196
816
810
596
586
458
450
351
342
233
226
128
124
64
62
32
31
16
16
7
7
2
2
0
0
0
0
ZONAL LUMENS AND PERCENTAGES
ZONE
0-30
0-40
0-60
0-90
40-90
60-90
90-180
0-180
LUMENS
1520
1895
2276
2318
423
42
0
2318
% LUMINAIRE
65.56
81.73
98.19
100.00
18.27
1.81
0.00
100.00
BEAM SIDE
22.5
45
1892 1892
1832 1827
1622 1620
1265 1262
884
876
573
574
385
389
297
296
242
242
187
189
123
125
66
68
32
33
15
15
7
7
2
2
0
0
0
0
0
0
67.5 ACROSS
1892 1892
1843 1805
1636 1600
1297 1278
915
916
597
603
399
402
297
301
241
244
189
190
126
125
69
68
34
33
16
15
7
7
2
2
0
0
0
0
0
0
ZONAL LUMENS AND PERCENTAGES
ZONE
0-30
0-40
0-60
0-90
40-90
60-90
90-180
0-180
Cone Of Light Tabulation
LUMENS
788
977
1184
1203
226
19
0
1203
% LUMINAIRE
65.50
81.21
98.40
100.00
18.79
1.60
0.00
100.00
Cone Of Light Tabulation
Mounting Height
(Feet)
Footcandles at
Nadir
Diameter (Feet)
Mounting Height
(Feet)
Footcandles at
Nadir
Diameter (Feet)
4.00
240
2.37
4.00
118
2.50
6.00
106
3.55
6.00
52.6
3.75
8.00
59.9
4.73
8.00
29.6
5.00
10.0
38.3
5.92
10.0
18.9
6.25
12.0
26.6
7.10
12.0
13.2
7.51
14.0
19.6
8.29
14.0
9.66
8.76
16.0
15.0
9.47
16.0
7.40
10.0
* Photometric data complies with LM-79-08, ANSI C82.77-02.
BROADWAVE® SERIES
2 OF 5
SS012517-2.0
DMX ACCESSORIES
The following DMX Accessories may be utilized with our DMX fixtures and controllers.
Item #
DI-1918
Type
Description
DMX 4-Channel
Decoder
Pair with a DMX controller to control solid color,
RGB, and RGBW LED fixtures. Features a
digital display for easy addressing.
DI-0820 (female)
DI-0821 (male)
Wireless DMX
Transmitter/Receiver
Wirelessly connects DMX devices: Fixture to
fixture, fixture to controller, and decoder to
decoder. Features XLR-3 connetions.
DI-1804
DMX 8-Way Splitter
Amplifies and splits a DMX signal up to 8 ways.
Features 1x male XLR-3 input connection, and
8x female XLR-3 output connections.
DI-1803
DMX XLR-3
Connector Pair
Utilize this XLR-3 connector pair to create
custom length DMX extensions. Sold by the
pair (male/female). Male: 2.8 x .71 in. (L x Dia.).
Female: 2.4 x .71 in. (L x Dia.)
DI-1806
XLR-3 to RJ45
Adapter Connector
Pair
Converts RJ45 data cables to XLR-3 DMX
connections. Sold by the pair (male/female)
Male & Female: 2.58 x .87 x .98 in. (L x W x H)
DI-1809
20 ft. DMX XLR-3
Extension Cable
Creates an extension between DMX fixtures
and accessories. Features XLR-3 connections.
Wire: 18/3 AWG. Male connection: 2.8 x .71 in.
(L x Dia.) Female: 2.4 x .71 in. (L x Dia.).
DI-1807
RJ45 Coupler
Female-to-female accessory quickly connects
two RJ45 accessories. Dimensions: 1.22 x .44
x .87 in. (L x W x H)
DI-1805
RJ45 Splice Cable
Lead wires connect to wall-mount DMX
controllers while RJ45 plug connects to DMX
accessories. Dimensions: 6.5 x .4 x .6 (L x W x H)
DI-1811
XLR-3 to RJ45
Adapter Cable Pair
Converts RJ45 port of 4-Channel DMX Decoder
to a standard XLR-3 connection. Sold by the pair
(male/female). Dimensions: 20 x .71 (L x Dia)
DI-1911
RJ45 Extension Cable
Creates a 10 ft. extension between DMX fixtures
and accessories utilizing RJ45 connections.
Image
Note: accessories sold separately
DMX CONTROLS
For a list of compatible controls see the product page at www.DiodeLED.com.
BROADWAVE® SERIES
3 OF 5
SS012517-2.0
MOUNTING
BROADWAVE® SERIES
4 OF 5
SS012517-2.0
ADDITIONAL RESOURCES
Visit the online product page at www.DiodeLED.com for additional resources including:
• WET LOCATION LED WALL WASHER Installation Guide
For system diagrams and full installation instructions.
• Voltage Drop Charts
Use to specify appropriate wire gauge for installation. Available at the ‘Tools & Resources’ page at www.DiodeLED.com.
SAFETY & DISCLOSURES
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Install in accordance with the National Electric Code and local regulations.
This product is intended to be installed and serviced by a qualified, licensed electrician.
Do not disassemble or modify this product. Doing so will void your warranty.
This fixture is not compatible with any traditional dimming controls. Wall washers can only be controlled/dimmed with the on-board interface or with
an external DMX controller. Please contact customer service for additional information.
Ensure all adjusting screws on mounting brackets and fixtures are properly secured prior to permanent installation.
When mounting to walls and ceilings, use applicable lag bolts and consider the strength of these surfaces versus the weight of the fixture.
It is recommended to power this fixture by a GFCI protected circuit.
This fixture is IP65 rated.
When installing outdoors or in a wet location, ensure water-resistant end caps are connected to all exposed wet location 3-pin M14 connections. If
attaching XLR-3 adapter cables seal all XLR-3 DMX connections with 1.25” wide heat shrink and finish with waterproof tape (not included). Do not
use liquid sealants of any kind.
This fixture is not to be used in or around chlorinated, treated or salt water due to the corrosive and degrading qualities of chlorine, saline, and other
chemicals on the fixture components. Keep at least 16 feet away from pools and spas.
Do not install product in an environment outside the listed ambient temperature. Ensure adequate airflow and heatsinking is considered when
mounting/installing.
Operating temperature is measured according to the minimum and maximum ambient temperature environment. Exceeding the maximum ambient
temperature may damage LED chips by reducing the total lamp life, lumen output, and/or adversely impact color consistency.
Ensure adequate airflow and heatsinking is considered when mounting/installing. Exceeding the maximum operating temperature may damage LED
chips by reducing the total lamp life, lumen output, and/or adversely impact color consistency.
Actual color may vary from what is pictured on this sheet and other print materials due to the limitations of photographic processes.
Lighting technology has some amount of gradual light degradation (output and/or color) over the lifespan of the products. Diode LED products are
designed to minimize degradation, but some light degradation and color shift is a normal part of the life span of any LED lighting system.
We reserve the right to modify and improve the design of our fixtures without prior notice. We cannot guarantee to match existing installed fixtures
for subsequent orders or replacements in regards to product appearance, CCT, or lumen output.
WARRANTY INFORMATION
Limited Warranty
This LED fixture has a two (2) year limited warranty from the date of shipment. This warranty does not include the additional accessories referenced
in this specification sheet. Complete warranty details for fixtures and additional accessories are available at www.DiodeLED.com under the ‘Tools &
Resources’ tab. For warranty related questions, please contact customer service.
Consumer’s Acknowledgment
Diode LED stands behind its products when they are used properly and according to our specifications. By purchasing our products, the purchaser
agrees and acknowledges that lighting design, configuration and installation is a complex process, wherein seemingly minor factors or changes in
layout and infield adjustments can have a significant impact on an entire system. Choosing the right components is essential. Diode LED is able to
work with the original purchaser to make an appropriate product selection to the extent of the limited information that the customer can provide, but
it is virtually impossible for Diode LED to design a system that foresees every unknown factor. For this reason, this Warranty does not cover problems
caused by improper design, configuration or installation issues. Any statement from a Diode LED employee or agent regarding a customer’s bill of
goods and/or purchase order is NOT an acknowledgement that the products purchased are designed and configured correctly. The purchaser agrees
and acknowledges that it is the customer’s responsibility to adhere strictly to all information contained in the Product Specification Sheets.
There is often more than one way to design, configure and layout an LED lighting application properly to achieve the same lighting effect. Diode LED
strongly recommends that licensed professionals be used in the design and installation of lighting systems that include Diode LED products. The
specifications include important information that a designer and installer should carefully review and strictly follow. Qualified designers and certified
and/or licensed installers, with access to the final installation environment, customer goals, and Diode LED product specifications can make the
requisite decisions appropriate for a successful finished lighting application.
® Toll Free: 877.817.6028 | Fax: 415.592.1596 | www.DiodeLED.com | info@DiodeLED.com
© 2017 Elemental LED, Inc. All rights reserved. Specifications are subject to change without notice.
BROADWAVE® SERIES
5 OF 5
SS012517-2.0
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising