power outlet
ELECTRICAL & POWER CONTROL
SECTION
PWO
POWER OUTLET
A
B
C
D
E
CONTENTS
POWER SOCKET
SYSTEM DESCRIPTION ............................. 12
PRECAUTION ............................................... 3
COMPONENT PARTS ...................................... 12
PRECAUTIONS ................................................... 3
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" ................................................................... 3
Precaution for Work .................................................. 3
PREPARATION ............................................ 4
PREPARATION ................................................... 4
Special Service Tool ................................................. 4
SYSTEM DESCRIPTION .............................. 5
COMPONENT PARTS ........................................ 5
Component Parts Location ......................................12
Component Description ...........................................12
Inverter Unit .............................................................12
AC 120V Outlet Main Switch ...................................12
AC 120V Outlet ........................................................12
I
ECU DIAGNOSIS INFORMATION .............. 14
J
INVERTER UNIT ............................................... 14
WIRING DIAGRAM ....................................... 6
WIRING DIAGRAM ...................................... 16
POWER SOCKET ............................................... 6
INVERTER UNIT ............................................... 16
BASIC INSPECTION ................................... 20
POWER SOCKET ............................................... 9
DIAGNOSIS AND REPAIR WORK FLOW ....... 20
PRECAUTION .............................................. 10
PRECAUTIONS ..................................................10
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" ................................................................. 10
Precaution for Work ................................................ 10
PREPARATION ........................................... 11
PREPARATION ..................................................11
Special Service Tool ............................................... 11
Revision: May 2013
K
L
Wiring Diagram ........................................................16
REMOVAL AND INSTALLATION ................ 9
AC 120 V OUTLET
H
System Diagram ......................................................13
System Description ..................................................13
Fail-safe ...................................................................13
Reference Value ......................................................14
Fail-safe ...................................................................15
Removal and Installation ........................................... 9
G
SYSTEM ............................................................ 13
Component Parts Location ........................................ 5
Wiring Diagram ......................................................... 6
F
Work Flow ................................................................20
PWO
N
DTC/CIRCUIT DIAGNOSIS ......................... 22
POWER SUPPLY AND GROUND CIRCUIT .... 22
O
Diagnosis Procedure ...............................................22
AC 120 V OUTLET MAIN SWITCH POWER
SUPPLY CIRCUIT ............................................. 23
Diagnosis Procedure ...............................................23
AC 120 V OUTLET MAIN SWITCH INPUT
SIGNAL CIRCUIT .............................................. 24
Diagnosis Procedure ...............................................24
PWO-1
2014 Pathfinder
P
Component Inspection (AC 120V Outlet Main
Switch) .................................................................... 24
AC 120 V POWER OUTPUT CIRCUIT .............. 26
Description .............................................................. 31
REMOVAL AND INSTALLATION .............. 32
Diagnosis Procedure .............................................. 26
INVERTER UNIT ................................................ 32
AC 120 V OUTLET MAIN SWITCH INDICATOR CIRCUIT .................................................... 28
AC 120V OUTLET MAIN SW ............................ 33
Removal and Installation ......................................... 32
Diagnosis Procedure .............................................. 28
Removal and Installation ......................................... 33
SYMPTOM DIAGNOSIS ............................. 29
AC 120 V OUTLET ............................................ 34
NO OUTPUT FROM AC 120 V OUTLET ........... 29
Diagnosis Procedure .............................................. 29
AC 120 V OUTLET MAIN SWITCH INDICATOR DOES NOT TURN ON ............................... 30
Diagnosis Procedure .............................................. 30
NORMAL OPERATING CONDITION ................ 31
Revision: May 2013
Removal and Installation ......................................... 34
SERVICE DATA AND SPECIFICATIONS
(SDS) .......................................................... 35
SERVICE DATA AND SPECIFICATIONS
(SDS) ................................................................. 35
AC 120V Power Outlet ............................................ 35
PWO-2
2014 Pathfinder
PRECAUTIONS
[POWER SOCKET]
< PRECAUTION >
PRECAUTION
A
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
B
INFOID:0000000009726161
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precaution for Work
INFOID:0000000009174828
C
D
E
F
G
H
I
J
• When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component K
with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a shop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
L
• If a part is specified as a non-reusable part, always replace it with a new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components:
PWO
- Water soluble dirt:
• Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
• Then rub with a soft, dry cloth.
N
- Oily dirt:
• Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty
area.
O
• Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
• Then rub with a soft, dry cloth.
- Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
- For genuine leather seats, use a genuine leather seat cleaner.
P
Revision: May 2013
PWO-3
2014 Pathfinder
PREPARATION
[POWER SOCKET]
< PREPARATION >
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000009174829
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
—
(J-42059)
Power socket removal tool
Removing power sockets
AWMIA1148GB
—
(J-46534)
Trim tool set
Removing trim components
AWJIA0483ZZ
Revision: May 2013
PWO-4
2014 Pathfinder
COMPONENT PARTS
[POWER SOCKET]
< SYSTEM DESCRIPTION >
SYSTEM DESCRIPTION
A
COMPONENT PARTS
Component Parts Location
INFOID:0000000009174830
B
C
D
E
F
G
H
I
AWMIA1326ZZ
1.
A/C and AV switch assembly
2.
Front power socket LH
3.
Front power socket RH (for cigarette
lighter)
4.
Center console
5.
Console power socket
6.
Luggage side finisher lower LH
7.
Rear cargo power socket
J
K
L
PWO
N
O
P
Revision: May 2013
PWO-5
2014 Pathfinder
POWER SOCKET
[POWER SOCKET]
< WIRING DIAGRAM >
WIRING DIAGRAM
POWER SOCKET
Wiring Diagram
INFOID:0000000009174831
ABMWA2109GB
Revision: May 2013
PWO-6
2014 Pathfinder
POWER SOCKET
[POWER SOCKET]
< WIRING DIAGRAM >
A
B
C
D
E
F
G
H
I
J
K
L
PWO
N
O
ABMIA4873GB
P
Revision: May 2013
PWO-7
2014 Pathfinder
POWER SOCKET
[POWER SOCKET]
< WIRING DIAGRAM >
ABMIA4874GB
Revision: May 2013
PWO-8
2014 Pathfinder
POWER SOCKET
[POWER SOCKET]
< REMOVAL AND INSTALLATION >
REMOVAL AND INSTALLATION
A
POWER SOCKET
Removal and Installation
INFOID:0000000009174832
FRONT CONSOLE POWER SOCKET, CONSOLE POWER SOCKET (IF EQUIPPED), REAR CONSOLE POWER SOCKET (IF EQUIPPED) or REAR CARGO POWER SOCKET
NOTE:
If unable to use the Tool because of power socket location or access to the harness connector, then further
removal of interior components may be required. Refer to IP-24, "Removal and Installation" (Front Console
Power Socket), IP-18, "Removal and Installation" (Console Power Socket), IP-29, "Disassembly and Assembly" (Rear Console Power Socket) or Rear Cargo Power Socket INT-31, "LUGGAGE SIDE LOWER FINISHER : Removal and Installation".
Remove the fuse for the power socket.
Insert one side of the Tool (A) into one of the square holes inside
the power socket.
Tool number
3.
4.
D
:
—
F
(J-42059)
G
Lift up the handle of the Tool until the other side snaps into the
other square hole in the power socket.
Pull the power socket straight out with the Tool.
H
AWMIA1182GB
5.
6.
C
E
Removal
1.
2.
B
Disconnect the harness connector from the power socket.
Remove the ring from the power socket finisher while pressing
the pawls.
I
J
K
L
WKIA1035E
Installation
Installation is in the reverse order of removal.
NOTE:
Make sure to align the tab with the square notched area during
installation.
PWO
N
O
P
AWMIA1183GB
Revision: May 2013
PWO-9
2014 Pathfinder
PRECAUTIONS
[AC 120 V OUTLET]
< PRECAUTION >
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009726162
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precaution for Work
INFOID:0000000009174834
• When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component
with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a shop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with a new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components:
- Water soluble dirt:
• Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
• Then rub with a soft, dry cloth.
- Oily dirt:
• Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty
area.
• Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
• Then rub with a soft, dry cloth.
- Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
- For genuine leather seats, use a genuine leather seat cleaner.
Revision: May 2013
PWO-10
2014 Pathfinder
PREPARATION
[AC 120 V OUTLET]
< PREPARATION >
PREPARATION
A
PREPARATION
Special Service Tool
INFOID:0000000009174835
B
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
—
(J-46534)
Trim tool set
Removing trim components
C
D
E
AWJIA0483ZZ
F
G
H
I
J
K
L
PWO
N
O
P
Revision: May 2013
PWO-11
2014 Pathfinder
COMPONENT PARTS
[AC 120 V OUTLET]
< SYSTEM DESCRIPTION >
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts Location
INFOID:0000000009174836
AWMIA1327ZZ
1.
Steering column
2.
AC 120V outlet main switch
3.
Rear air control
4.
AC 120V outlet
5.
Luggage side finisher lower LH
6.
Inverter unit (view with storage box
removed)
Component Description
INFOID:0000000009174837
Component
Reference
Inverter unit
PWO-12, "Inverter Unit"
AC 120V outlet main switch
PWO-12, "AC 120V Outlet Main Switch"
AC 120V outlet
PWO-12, "AC 120V Outlet"
Inverter Unit
INFOID:0000000009174838
The inverter unit converts 12V DC to 120V AC.
AC 120V Outlet Main Switch
INFOID:0000000009174839
The AC outlet main switch allows operation of the inverter unit in 150W AC 120V mode.
AC 120V Outlet
INFOID:0000000009174840
The AC 120V outlet allow use of AC components up to 150W.
Revision: May 2013
PWO-12
2014 Pathfinder
SYSTEM
[AC 120 V OUTLET]
< SYSTEM DESCRIPTION >
SYSTEM
A
System Diagram
INFOID:0000000009174841
B
C
D
E
JSMIA0295GB
System Description
INFOID:0000000009174842
• When turning ON the AC 120V outlet main switch with the ignition switch ON, the Indicator turns ON and the
inverter unit is activated allowing the use of devices up to 150W.
• The inverter unit converts 12V DC to 120V AC and outputs the converted voltage to the AC 120V outlet two
seconds after the AC 120V outlet main switch is turned ON.
Fail-safe
Malfunction item
Fail-safe condition
Fail-safe cancellation condition
Inverter unit power supply voltage is greater than
15V
When inverter unit input voltage rises above 15V, the
output will be suspended to protect the inverter unit.
After the inverter unit power supply voltage drops
below 15V, the AC 120V outlet main switch ON ⇒
OFF ⇒ ON operation allows normal return.
When inverter unit input voltage is lowered, the output will be suspended to protect the battery from running out.
After the inverter unit power supply voltage rises
above 11.5V, the AC 120V outlet main switch ON ⇒
OFF ⇒ ON operation allows normal return.
Inverter unit AC 120V
output voltage is greater
than 170V
When inverter unit AC 120V output voltage is greater
than 170V, the output will be suspended.
After the inverter unit AC 120V output voltage drops
below 170V, the AC 120V outlet main switch ON ⇒
OFF ⇒ ON operation allows normal return.
Inverter unit input current
is greater than 13.3A
When inverter unit input current rises above 13.3A,
the output will be suspended to prevent over current
(e.g., connecting an electric appliance exceeding
rated output).
After the inverter unit input current drops below
13.3A, the AC 120V outlet main switch ON ⇒ OFF
⇒ ON operation allows normal return.
Inverter unit is overheated
When the inverter unit is overheated [thermistor temperature above 100°C (212°F)], the output will be
suspended to protect the inverter unit.
After the inverter unit temperature is lowered, the
AC 120V outlet main switch ON ⇒ OFF ⇒ ON operation allows normal return.
When inverter unit output signal is shorted, the output will be suspended.
After recovering from inverter unit output signal
short, the AC 120V outlet main switch ON ⇒ OFF
⇒ ON operation allows normal return.
Inverter unit power supply voltage is less than 9V
Inverter unit output signal
(AC 120V output signal)
is shorted
Revision: May 2013
G
H
INFOID:0000000009174843
When a malfunction listed below occurs, the inverter unit turns OFF the AC 120V outlet main switch indicator
and stops the output.
Inverter unit power supply voltage is less than
11.5V for 2 seconds or
more
F
I
J
K
L
PWO
PWO-13
2014 Pathfinder
N
O
P
INVERTER UNIT
[AC 120 V OUTLET]
< ECU DIAGNOSIS INFORMATION >
ECU DIAGNOSIS INFORMATION
INVERTER UNIT
Reference Value
INFOID:0000000009174844
TERMINAL LAYOUT
JSMIA0395ZZ
PHYSICAL VALUES
Terminal No.
(Wire color)
+
1
(W)
Description
−
5
(B)
Signal name
AC output 2
Condition
Input/
Output
Output
Value
(Approx.)
AC 120V outlet main
switch OFF
0V
AC 120V outlet main
switch ON
(Using circuit tester)
AC 120V
Reference value
Ignition
switch ON
AC 120V outlet main
switch ON
(Using oscilloscope)
JSMIA0397GB
AC 120V
4
(W)
5
(B)
Ground
1
(W)
Battery power supply
AC output 1
Input
Output
Ignition switch OFF
Battery voltage
AC 120V outlet main
switch OFF
0V
AC 120V outlet main
switch ON
(Using circuit tester)
AC 120V
Reference value
Ignition
switch ON
AC 120V outlet main
switch ON
(Using oscilloscope)
JSMIA0397GB
AC 120V
Revision: May 2013
PWO-14
2014 Pathfinder
INVERTER UNIT
[AC 120 V OUTLET]
< ECU DIAGNOSIS INFORMATION >
Terminal No.
(Wire color)
−
+
6
(W)
7
(G)
Description
Signal name
AC 120 V outlet main
switch
Ground
8
(B)
AC 120 V outlet main
switch
Ground
Input/
Output
Input
Output
—
Value
(Approx.)
Condition
Ignition
switch ON
Ignition
switch ON
AC 120V outlet main
switch OFF
0V
AC 120V outlet main
switch ON
Battery voltage
AC 120V outlet main
switch OFF
0V
AC 120V outlet main
switch ON
5.2V
Ignition switch ON
0V
A
B
C
D
E
CAUTION:
• To measure AC 120V output signal, always use the circuit tester or oscilloscope AC range.
Never allow the probes to contact each other.
• Because of modified sine wave output of the AC 120V output signal, voltage cannot be measured
accurately without using a circuit tester that can measure true RMS (root mean square).
F
Fail-safe
G
INFOID:0000000009174845
When a malfunction listed below occurs, the inverter unit turns OFF the AC 120V outlet main switch indicator
and stops the output.
H
Malfunction item
Fail-safe condition
Fail-safe cancellation condition
Inverter unit power supply voltage is greater than
15V
When inverter unit input voltage rises above 15V, the
output will be suspended to protect the inverter unit.
After the inverter unit power supply voltage drops
below 15V, the AC 120V outlet main switch ON ⇒
OFF ⇒ ON operation allows normal return.
When inverter unit input voltage is lowered, the output will be suspended to protect the battery from running out.
After the inverter unit power supply voltage rises
above 11.5V, the AC 120V outlet main switch ON ⇒
OFF ⇒ ON operation allows normal return.
Inverter unit AC 120V
output voltage is greater
than 170V
When inverter unit AC 120V output voltage is greater
than 170V, the output will be suspended.
After the inverter unit AC 120V output voltage drops
below 170V, the AC 120V outlet main switch ON ⇒
OFF ⇒ ON operation allows normal return.
Inverter unit input current
is greater than 13.3A
When inverter unit input current rises above 13.3A,
the output will be suspended to prevent over current
(e.g., connecting an electric appliance exceeding
rated output).
After the inverter unit input current drops below
13.3A, the AC 120V outlet main switch ON ⇒ OFF
⇒ ON operation allows normal return.
Inverter unit is overheated
When the inverter unit is overheated [thermistor temperature above 100°C (212°F)], the output will be
suspended to protect the inverter unit.
After the inverter unit temperature is lowered, the
AC 120V outlet main switch ON ⇒ OFF ⇒ ON operation allows normal return.
N
Inverter unit output signal
(AC 120V output signal)
is shorted
When inverter unit output signal is shorted, the output will be suspended.
After recovering from inverter unit output signal
short, the AC 120V outlet main switch ON ⇒ OFF
⇒ ON operation allows normal return.
O
Inverter unit power supply voltage is less than
11.5V for 2 seconds or
more
Inverter unit power supply voltage is less than 9V
I
J
K
L
PWO
P
Revision: May 2013
PWO-15
2014 Pathfinder
INVERTER UNIT
[AC 120 V OUTLET]
< WIRING DIAGRAM >
WIRING DIAGRAM
INVERTER UNIT
Wiring Diagram
INFOID:0000000009174846
ABMWA2108GB
Revision: May 2013
PWO-16
2014 Pathfinder
INVERTER UNIT
[AC 120 V OUTLET]
< WIRING DIAGRAM >
A
B
C
D
E
F
G
H
I
J
K
L
PWO
N
O
ABMIA4870GB
P
Revision: May 2013
PWO-17
2014 Pathfinder
INVERTER UNIT
[AC 120 V OUTLET]
< WIRING DIAGRAM >
ABMIA4871GB
Revision: May 2013
PWO-18
2014 Pathfinder
INVERTER UNIT
[AC 120 V OUTLET]
< WIRING DIAGRAM >
A
B
C
D
E
F
G
H
I
J
K
L
PWO
N
O
ABMIA4872GB
P
Revision: May 2013
PWO-19
2014 Pathfinder
DIAGNOSIS AND REPAIR WORK FLOW
[AC 120 V OUTLET]
< BASIC INSPECTION >
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORK FLOW
Work Flow
INFOID:0000000009174847
OVERALL SEQUENCE
AWMIA1287GB
DETAILED FLOW
1.INTERVIEW FOR MALFUNCTION
Interview the customer about the symptom.
>> GO TO 2.
2.SYMPTOM CHECK
Check the symptom from the customer's information.
>> GO TO 3.
3.FAIL-SAFE ACTIVATION CHECK
Check that the symptom is a fail-safe condition.
Is fail-safe activated?
YES >> GO TO 4.
NO
>> GO TO 5.
4.SYSTEM DIAGNOSIS
Perform diagnosis for the fail-safe activated system. Specify the malfunctioning component.
Revision: May 2013
PWO-20
2014 Pathfinder
DIAGNOSIS AND REPAIR WORK FLOW
[AC 120 V OUTLET]
< BASIC INSPECTION >
>> GO TO 6.
5.SYMPTOM DIAGNOSIS
A
Perform symptom diagnosis. Specify the malfunctioning component.
B
>> GO TO 6.
6.MALFUNCTIONING COMPONENT REPAIR
C
Repair or replace the malfunctioning component.
>> GO TO 7.
D
7.REPAIR CHECK (OPERATION CHECK)
Check operation of AC 120V outlet.
Does the outlet operate normally?
YES >> Inspection End.
NO
>> GO TO 3.
E
F
G
H
I
J
K
L
PWO
N
O
P
Revision: May 2013
PWO-21
2014 Pathfinder
POWER SUPPLY AND GROUND CIRCUIT
[AC 120 V OUTLET]
< DTC/CIRCUIT DIAGNOSIS >
DTC/CIRCUIT DIAGNOSIS
POWER SUPPLY AND GROUND CIRCUIT
Diagnosis Procedure
INFOID:0000000009174848
Regarding Wiring Diagram information, refer to PWO-16, "Wiring Diagram".
1.CHECK FUSE AND FUSIBLE LINK
Check that the following fuse and fusible link are not blown.
Signal name
Fuse No.
Battery power supply
69 (30A)
Is the fuse blown?
YES >> Replace the blown fuse after repairing the affected circuit.
NO
>> GO TO 2.
2.CHECK INVERTER UNIT POWER SUPPLY CIRCUIT
1.
2.
Disconnect inverter unit connector B82.
Check voltage between inverter unit connector B82 terminal 4 and ground.
Inverter unit
Connector
Terminal
B82
4
Ground
Voltage
(Approx.)
—
Battery voltage
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Repair or replace the inverter unit power supply circuit.
3.CHECK INVERTER UNIT GROUND CIRCUIT
Check continuity between inverter unit connector B82 terminal 8 and ground.
Inverter unit
Connector
Terminal
B82
8
Ground
Continuity
—
Yes
Is the inspection result normal?
YES >> Inspection End.
NO
>> Repair or replace the inverter unit ground circuit.
Revision: May 2013
PWO-22
2014 Pathfinder
AC 120 V OUTLET MAIN SWITCH POWER SUPPLY CIRCUIT
[AC 120 V OUTLET]
< DTC/CIRCUIT DIAGNOSIS >
AC 120 V OUTLET MAIN SWITCH POWER SUPPLY CIRCUIT
A
Diagnosis Procedure
INFOID:0000000009174849
B
Regarding Wiring Diagram information, refer to PWO-16, "Wiring Diagram".
C
1.CHECK FUSE
Check that the following fuse is not blown.
D
Signal name
Fuse No.
Ignition switch ON or START
30 (10A)
E
Is the fuse blown?
YES >> Replace the blown fuse after repairing the affected circuit.
NO
>> GO TO 2.
F
2.CHECK POWER SUPPLY FOR AC 120V OUTLET MAIN SWITCH
1.
2.
Turn ignition switch ON.
Check voltage between AC 120V outlet main switch connector M88 terminal 1 and ground.
AC 120V outlet main switch
Connector
Terminal
M88
1
Condition
Voltage
(Approx.)
Ignition switch ON
Battery voltage
Ignition switch OFF
0V
Ground
—
G
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Repair or replace the AC 120V main switch power supply circuit.
Turn ignition switch OFF.
Check continuity between AC 120V outlet main switch connector M88 terminal 6 and ground.
AC 120V outlet main switch
Connector
Terminal
M88
6
I
J
3.CHECK AC 120V OUTLET MAIN SWITCH GROUND CIRCUIT
1.
2.
H
Ground
Continuity
—
Yes
K
L
PWO
Is the inspection result normal?
YES >> Inspection End.
NO
>> Repair or replace the AC 120V main switch ground circuit.
N
O
P
Revision: May 2013
PWO-23
2014 Pathfinder
AC 120 V OUTLET MAIN SWITCH INPUT SIGNAL CIRCUIT
[AC 120 V OUTLET]
< DTC/CIRCUIT DIAGNOSIS >
AC 120 V OUTLET MAIN SWITCH INPUT SIGNAL CIRCUIT
Diagnosis Procedure
INFOID:0000000009174850
Regarding Wiring Diagram information, refer to PWO-16, "Wiring Diagram".
1.CHECK AC 120V OUTLET MAIN SWITCH INPUT SIGNAL
1.
2.
3.
Turn ignition switch ON.
AC 120V outlet main switch ON.
Check for voltage between the inverter unit connector B82 terminal 6 and ground.
Inverter unit
Connector
Ground
Terminal
B82
6
—
Voltage
(Approx.)
Condition
AC 120V outlet main
switch OFF
0V
AC 120V outlet main
switch ON
Battery voltage
Is the inspection result normal?
YES >> Inspection End.
NO
>> GO TO 2.
2.CHECK AC 120V OUTLET MAIN SWITCH
Check AC 120V outlet main switch. Refer to PWO-24, "Component Inspection (AC 120V Outlet Main Switch)".
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Replace AC 120V outlet main switch.
3.CHECK HARNESS BETWEEN INVERTER UNIT AND AC 120V OUTLET MAIN SWITCH
1.
2.
Disconnect inverter unit connector.
Check for continuity between the inverter unit connector B82 terminal 6 and AC 120V outlet main switch
connector M88 terminal 3.
Inverter unit
3.
AC 120V outlet main switch
Connector
Terminal
Connector
Terminal
B82
6
M88
3
Continuity
Yes
Check for continuity between inverter unit connector B82 terminal 6 and ground.
Inverter unit
Connector
Terminal
B82
6
Ground
Continuity
—
No
Is the inspection result normal?
YES >> Inspection End.
NO
>> Repair or replace the AC 120V outlet main switch input signal circuit.
Component Inspection (AC 120V Outlet Main Switch)
INFOID:0000000009174851
1.CHECK AC 120V OUTLET MAIN SWITCH
1.
2.
3.
Turn ignition switch OFF.
Disconnect AC 120V outlet main switch connector.
Check continuity between terminals 1 and 3 of AC 120V outlet main switch.
Revision: May 2013
PWO-24
2014 Pathfinder
AC 120 V OUTLET MAIN SWITCH INPUT SIGNAL CIRCUIT
[AC 120 V OUTLET]
< DTC/CIRCUIT DIAGNOSIS >
AC 120V outlet main switch terminals
1–3
Condition
Continuity
AC 120V outlet main switch ON
Yes
AC 120V outlet main switch OFF
No
A
B
Is the inspection result normal?
YES >> Inspection End.
NO
>> Replace AC 120V outlet main switch.
C
D
E
F
G
H
I
J
K
L
PWO
N
O
P
Revision: May 2013
PWO-25
2014 Pathfinder
AC 120 V POWER OUTPUT CIRCUIT
[AC 120 V OUTLET]
< DTC/CIRCUIT DIAGNOSIS >
AC 120 V POWER OUTPUT CIRCUIT
Diagnosis Procedure
INFOID:0000000009174852
Regarding Wiring Diagram information, refer to PWO-16, "Wiring Diagram".
1.CHECK HARNESS BETWEEN INVERTER UNIT AND AC 120V OUTLET
1.
2.
3.
Turn ignition switch OFF.
Disconnect inverter unit and AC 120V outlet connectors.
Check continuity between inverter unit connector B82 terminals 5, 1 and AC 120V outlet connector M256
terminals 1, 4.
Inverter unit
Connector
AC 120V outlet
Terminal
5
B82
4.
Connector
1
M256
1
4
Continuity
Yes
Check continuity between inverter unit connector B82 terminals 5, 1 and ground.
Inverter unit
Connector
B82
5.
Terminal
Terminal
5
1
Ground
Continuity
—
No
Check continuity between inverter unit connector B82 terminals 5 and 1.
Inverter unit
Connector
B82
Continuity
Terminal
5
1
No
Is the inspection result normal?
YES >> GO TO 2.
NO
>> Repair or replace the harness or connectors.
2.CHECK INVERTER UNIT OUTPUT SIGNAL
1.
2.
3.
4.
Connect inverter unit and AC 120V outlet connectors.
Turn ignition switch ON.
AC 120V outlet main switch ON (AC 120V outlet main switch indicator ON).
Check voltage between inverter unit connector B82 terminals 5 and 1.
CAUTION:
• To measure AC 120V output signal, always use the circuit tester AC range.
• Never allow the probes to contact each other.
Inverter unit connector B82 terminals
(+)
(-)
5
1
Condition
AC 120V outlet main switch
Voltage
(Approx.)
OFF
0V
ON
AC 120V
Is the inspection result normal?
YES >> GO TO 3
NO
>> Replace inverter unit.
3.CHECK AC 120V OUTLET VOLTAGE
Check voltage between AC 120V outlet M256 terminals 1 and 4.
Revision: May 2013
PWO-26
2014 Pathfinder
AC 120 V POWER OUTPUT CIRCUIT
< DTC/CIRCUIT DIAGNOSIS >
CAUTION:
• To measure AC 120V output signal, always use the circuit tester AC range.
• Never allow the probes to contact each other.
AC 120V outlet connector M256 terminals
(+)
(-)
1
4
Condition
[AC 120 V OUTLET]
A
AC 120V outlet main switch
Voltage
(Approx.)
OFF
0V
ON
AC 120V
Is the inspection result normal?
YES >> GO TO 4
NO
>> Replace AC 120V outlet.
B
C
D
4.CHECK AC 120V OUTLET GROUND CIRCUIT
1.
2.
3.
4.
E
AC 120V outlet main switch OFF.
Turn ignition switch OFF.
Disconnect AC 120V outlet connector.
Check continuity between AC 120V outlet connector M256 terminal 3 and ground.
AC 120V outlet
Connector
Terminal
M256
3
F
Ground
Continuity
—
Yes
Is the inspection result normal?
YES >> Replace AC 120V outlet.
NO
>> Repair AC 120V outlet ground circuit.
G
H
I
J
K
L
PWO
N
O
P
Revision: May 2013
PWO-27
2014 Pathfinder
AC 120 V OUTLET MAIN SWITCH INDICATOR CIRCUIT
[AC 120 V OUTLET]
< DTC/CIRCUIT DIAGNOSIS >
AC 120 V OUTLET MAIN SWITCH INDICATOR CIRCUIT
Diagnosis Procedure
INFOID:0000000009174853
Regarding Wiring Diagram information, refer to PWO-16, "Wiring Diagram".
1.CHECK HARNESS BETWEEN INVERTER UNIT AND AC 120 V OUTLET MAIN SWITCH
1.
2.
3.
Turn ignition switch OFF.
Disconnect inverter unit and AC 120 V outlet main switch connectors.
Check continuity between inverter unit connector B82 terminal 7 and AC 120 V main switch connector
M88 terminal 5.
Inverter unit
4.
AC 120 V outlet main switch
Connector
Terminal
Connector
Terminal
B82
7
M88
5
Continuity
Yes
Check continuity between inverter unit connector B82 terminal 7 and ground.
Inverter unit
Connector
Terminal
B82
7
Continuity
Ground
No
Is the inspection result normal?
YES >> GO TO 2.
NO
>> Repair or replace the harness or connectors.
2.CHECK AC 120 V OUTLET MAIN SWITCH GROUND CIRCUIT
Check continuity between AC 120 V outlet main switch connector M88 terminal 6 and ground.
AC 120 V outlet main switch
Connector
Terminal
M88
6
Continuity
Ground
Yes
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Repair AC 120 V outlet main switch ground circuit.
3.CHECK AC 120 V OUTLET MAIN SWITCH INDICATOR OUTPUT SIGNAL
1.
2.
3.
4.
Connect AC 120 V outlet main switch and inverter unit connectors.
Turn ignition switch ON.
AC 120 V outlet main switch ON.
Check voltage between the inverter unit connector B82 terminal 7 and ground.
Inverter unit
Condition
Connector
Terminal
B82
7
Ground
—
AC 120V outlet main
switch
Voltage
(Approx.)
OFF
0V
ON
5.2V
Is the inspection result normal?
YES >> Replace AC 120 V outlet main switch.
NO
>> Replace inverter unit.
Revision: May 2013
PWO-28
2014 Pathfinder
NO OUTPUT FROM AC 120 V OUTLET
[AC 120 V OUTLET]
< SYMPTOM DIAGNOSIS >
SYMPTOM DIAGNOSIS
A
NO OUTPUT FROM AC 120 V OUTLET
Diagnosis Procedure
INFOID:0000000009174854
B
1.CHECK FAIL-SAFE ACTIVATION
Check if the symptom is caused by a fail-safe operation. Refer to PWO-15, "Fail-safe".
Is fail-safe operating?
YES >> Repair the part causing fail-safe operation.
NO
>> GO TO 2.
C
D
2.CHECK INVERTER UNIT POWER SUPPLY CIRCUIT
Check inverter unit power supply circuit. Refer to PWO-22, "Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
E
F
3.CHECK AC 120V OUTLET MAIN SWITCH POWER SUPPLY CIRCUIT
Check AC 120V outlet main switch power supply circuit. Refer to PWO-23, "Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 4.
NO
>> Repair or replace the malfunctioning parts.
4.CHECK AC 120V OUTLET MAIN SWITCH INPUT SIGNAL CIRCUIT
Check AC 120V outlet main switch input signal circuit. Refer to PWO-24, "Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Repair or replace the malfunctioning parts.
G
H
I
5.CHECK INVERTER UNIT POWER OUTPUT CIRCUIT
J
Check inverter unit power output circuit. Refer to PWO-26, "Diagnosis Procedure".
Is the inspection result normal?
YES >> Refer to GI-49, "Intermittent Incident".
NO
>> Repair or replace the malfunctioning parts.
K
L
PWO
N
O
P
Revision: May 2013
PWO-29
2014 Pathfinder
AC 120 V OUTLET MAIN SWITCH INDICATOR DOES NOT TURN ON
[AC 120 V OUTLET]
< SYMPTOM DIAGNOSIS >
AC 120 V OUTLET MAIN SWITCH INDICATOR DOES NOT TURN ON
Diagnosis Procedure
INFOID:0000000009174855
1.CHECK FAIL-SAFE ACTIVATION
Check if the symptom is caused by a fail-safe operation. Refer to PWO-15, "Fail-safe".
Is fail-safe operating?
YES >> Repair the part causing fail-safe operation.
NO
>> GO TO 2.
2.CHECK INVERTER UNIT POWER SUPPLY CIRCUIT
Check inverter unit power supply circuit. Refer to PWO-22, "Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.CHECK AC 120V OUTLET MAIN SWITCH POWER SUPPLY CIRCUIT
Check AC 120V outlet main switch power supply circuit. Refer to PWO-23, "Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 4.
NO
>> Repair or replace the malfunctioning parts.
4.CHECK AC 120V OUTLET MAIN SWITCH INPUT SIGNAL CIRCUIT
Check AC 120V outlet main switch input signal circuit. Refer to PWO-24, "Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Repair or replace the malfunctioning parts.
5.CHECK AC 120V OUTLET MAIN SWITCH INDICATOR CIRCUIT
Check AC 120V outlet main switch indicator circuit. Refer to PWO-28, "Diagnosis Procedure".
Is the inspection result normal?
YES >> Refer to GI-49, "Intermittent Incident".
NO
>> Repair or replace the malfunctioning parts.
Revision: May 2013
PWO-30
2014 Pathfinder
NORMAL OPERATING CONDITION
[AC 120 V OUTLET]
< SYMPTOM DIAGNOSIS >
NORMAL OPERATING CONDITION
Description
A
INFOID:0000000009174856
Because of modified sine wave output, the AC 120V outlet may not operate normally for electric appliance of
which electric power consumption is 150W or less.
• Electric appliances requiring a large amount of electric power consumption at startup (e.g., CRT-based TV,
power tool)
• Measuring instruments for data requiring accuracy (e.g., medical equipment, measuring instrument)
• Microprocessor-controlled appliances (e.g., microprocessor-controlled blanket)
Noise may be caused in radio or TV, depending on an electric appliance.
B
C
D
E
F
G
H
I
J
K
L
PWO
N
O
P
Revision: May 2013
PWO-31
2014 Pathfinder
INVERTER UNIT
[AC 120 V OUTLET]
< REMOVAL AND INSTALLATION >
REMOVAL AND INSTALLATION
INVERTER UNIT
Removal and Installation
INFOID:0000000009174857
REMOVAL
1.
2.
Remove inverter unit fuse.
Remove luggage side lower finisher LH. Refer to INT-31, "LUGGAGE SIDE LOWER FINISHER :
Removal and Installation".
NOTE:
The inverter unit is located under the storage box bracket (LH)
(1).
ALMIA0555ZZ
3.
4.
5.
Remove the inverter unit bolts.
Disconnect the harness connector from the inverter unit (1).
Remove the inverter unit (1).
ALMIA0557ZZ
INSTALLATION
Installation is in the reverse order of removal.
Revision: May 2013
PWO-32
2014 Pathfinder
AC 120V OUTLET MAIN SW
[AC 120 V OUTLET]
< REMOVAL AND INSTALLATION >
AC 120V OUTLET MAIN SW
A
Removal and Installation
INFOID:0000000009174858
REMOVAL
1.
2.
3.
B
Remove the inverter unit fuse.
Remove the instrument lower panel LH. Refer to IP-25, "Removal and Installation".
Remove three screws (A, B) that retain the lower switch assembly (2).
(1) Upper switch assembly
(C) Upper switch assembly screws
C
D
E
F
ALMIA0554ZZ
4.
Release upper tab (B) and lower tab (C) using a suitable tool
(A), then remove the AC 120V outlet main switch (3) from the
lower switch assembly.
(1) Blank
(2) Blank
(4) Tow mode switch (if equipped)
G
H
I
J
K
L
PWO
ALMIA0567ZZ
INSTALLATION
N
Installation is in the reverse order of removal.
O
P
Revision: May 2013
PWO-33
2014 Pathfinder
AC 120 V OUTLET
[AC 120 V OUTLET]
< REMOVAL AND INSTALLATION >
AC 120 V OUTLET
Removal and Installation
INFOID:0000000009174859
REMOVAL
1.
2.
Remove center console rear finisher. Refer to IP-27, "Exploded View".
Release the pawl from the back of the center console rear finisher to remove the AC 120 V outlet.
INSTALLATION
Installation is in the reverse order of removal.
Revision: May 2013
PWO-34
2014 Pathfinder
SERVICE DATA AND SPECIFICATIONS (SDS)
[AC 120 V OUTLET]
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
A
SERVICE DATA AND SPECIFICATIONS (SDS)
AC 120V Power Outlet
INFOID:0000000009174860
Rated voltage
AC 120 V
Maximum electric capacity
150 W or less (Total)
Maximum current
Up to 30 A (Total)
B
C
D
E
F
G
H
I
J
K
L
PWO
N
O
P
Revision: May 2013
PWO-35
2014 Pathfinder
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising